One document matched: draft-zhang-ccamp-gmpls-evolving-g709-07.txt
Differences from draft-zhang-ccamp-gmpls-evolving-g709-06.txt
Network Working Group Fatai Zhang
Internet Draft Huawei
Category: Standards Track Guoying Zhang
CATR
Sergio Belotti
Alcatel-Lucent
D. Ceccarelli
Ericsson
Expires: September 11 2011 March 11, 2011
Generalized Multi-Protocol Label Switching (GMPLS) Signaling
Extensions for the evolving G.709 Optical Transport Networks Control
draft-zhang-ccamp-gmpls-evolving-g709-07.txt
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with
the provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on September 11, 2011.
Abstract
Recent progress in ITU-T Recommendation G.709 standardization has
introduced new ODU containers (ODU0, ODU4, ODU2e and ODUflex) and
enhanced Optical Transport Networking (OTN) flexibility. Several
Zhang Expires September 2011 [Page 1]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
recent documents have proposed ways to modify GMPLS signaling
protocols to support these new OTN features.
It is important that a single solution is developed for use in GMPLS
signaling and routing protocols. This solution must support ODUk
multiplexing capabilities, address all of the new features, be
acceptable to all equipment vendors, and be extensible considering
continued OTN evolution.
This document describes the extensions to the Generalized Multi-
Protocol Label Switching (GMPLS) signaling to control the evolving
Optical Transport Networks (OTN) addressing ODUk multiplexing and new
features including ODU0, ODU4, ODU2e and ODUflex.
Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
Table of Contents
1. Introduction .................................................. 3
2. Terminology ................................................... 3
3. GMPLS Extensions for the Evolving G.709 - Overview ............ 4
4. Extensions for Traffic Parameters for the Evolving G.709 ...... 5
4.1. Usage of ODUflex(CBR) Traffic Parameter .................. 6
4.2. Example of ODUflex(CBR) Traffic Parameter ................ 7
5. Generalized Label ............................................. 8
5.1. New definition of ODUk Label ............................. 8
5.2. Examples ................................................ 12
5.3. Label Distribution Procedure ............................ 13
5.3.1. Notification on Label Error ........................ 14
5.4. Supporting Virtual Concatenation and Multiplication ..... 15
5.5. Supporting Multiplexing Hierarchy ....................... 15
5.6. Control Plane Backward Compatibility Considerations ..... 16
6. Security Considerations ...................................... 18
7. IANA Considerations .......................................... 18
8. References ................................................... 18
8.1. Normative References .................................... 18
8.2. Informative References .................................. 20
9. Authors' Addresses ........................................... 20
Acknowledgment .................................................. 22
Zhang Expires September 2011 [Page 2]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
1. Introduction
Generalized Multi-Protocol Label Switching (GMPLS) [RFC3945] extends
MPLS to include Layer-2 Switching (L2SC), Time-Division Multiplex
(e.g., SONET/SDH, PDH, and ODU), Wavelength (OCh, Lambdas) Switching,
and Spatial Switching (e.g., incoming port or fiber to outgoing port
or fiber). [RFC3471] presents a functional description of the
extensions to Multi-Protocol Label Switching (MPLS) signaling
required to support Generalized MPLS. RSVP-TE-specific formats and
mechanisms and technology specific details are defined in [RFC3473].
With the evolution and deployment of G.709 technology, it is
necessary that appropriate enhanced control technology support be
provided for G.709. [RFC4328] describes the control technology
details that are specific to foundation G.709 Optical Transport
Networks (OTN), as specified in the ITU-T Recommendation G.709 [G709-
V1], for ODUk deployments without multiplexing.
In addition to increasing need to support ODUk multiplexing, the
evolution of OTN has introduced additional containers and new
flexibility. For example, ODU0, ODU2e, ODU4 containers and ODUflex
are developed in [G709-V3].
In addition, the following issues require consideration:
- Support for hitless adjustment of ODUflex, which is to be
specified in ITU-T G.hao.
- Support for Tributary Port Number. The Tributary Port Number
has to be negotiated on each link for flexible assignment of
tributary ports to tributary slots in case of LO-ODU over HO-
ODU (e.g., ODU2 into ODU3).
Therefore, it is clear that [RFC4328] has to be updated or superceded
in order to support ODUk multiplexing, as well as other ODU
enhancements introduced by evolution of OTN standards.
This document updates [RFC4328] extending the G.709 ODUk traffic
parameters and also presents a new OTN label format which is very
flexible and scalable.
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
Zhang Expires September 2011 [Page 3]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
3. GMPLS Extensions for the Evolving G.709 - Overview
New features for the evolving OTN, for example, new ODU0, ODU2e, ODU4
and ODUflex containers are specified in [G709-V3]. The corresponding
new signal types are summarized below:
- Optical Channel Transport Unit (OTUk):
. OTU4
- Optical Channel Data Unit (ODUk):
. ODU0
. ODU2e
. ODU4
. ODUflex
A new Tributary Slot (TS) granularity (i.e., 1.25 Gbps) is also
described in [G709-V3]. Thus, there are now two TS granularities for
the foundation OTN ODU1, ODU2 and ODU3 containers. The TS granularity
at 2.5 Gbps is used on legacy interfaces while the new 1.25 Gbps will
be used for the new interfaces.
In addition to the support of ODUk mapping into OTUk (k = 1, 2, 3, 4),
the evolving OTN [G.709-V3] encompasses the multiplexing of ODUj (j =
0, 1, 2, 2e, 3, flex) into an ODUk (k > j), as described in Section
3.1.2 of [OTN-frwk].
Virtual Concatenation (VCAT) of OPUk (OPUk-Xv, k = 1/2/3, X = 1...256)
are also supported by [OTN-V3]. Note that VCAT of OPU0 / OPU2e / OPU4
/ OPUflex are not supported per [OTN-V3].
[RFC4328] describes GMPLS signaling extensions to support the control
for G.709 Optical Transport Networks (OTN) [G709-V1]. However,
[RFC4328] needs to be updated because it does not provide the means
to signal all the new signal types and related mapping and
multiplexing functionalities. Moreover, it supports only the
deprecated auto-MSI mode which assumes that the Tributary Port Number
is automatically assigned in the transmit direction and not checked
in the receive direction.
This document extends the G.709 traffic parameters described in
[RFC4328] and presents a new OTN label format which is very flexible
and scalable. Additionally, procedures about Tributary Port Number
assignment through control plane are also provided in this document.
Zhang Expires September 2011 [Page 4]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
4. Extensions for Traffic Parameters for the Evolving G.709
The traffic parameters for G.709 are defined as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Signal Type | Tolerance | NMC |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NVC | Multiplier (MT) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Bit_Rate |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The Signal Type should be extended to cover the new Signal Type
introduced by the evolving OTN. The new Signal Type is extended as
follows:
Value Type
----- ----
0 Not significant
1 ODU1 (i.e., 2.5 Gbps)
2 ODU2 (i.e., 10 Gbps)
3 ODU3 (i.e., 40 Gbps)
4 ODU4 (i.e., 100 Gbps)
5 Reserved (for future use)
6 OCh at 2.5 Gbps
7 OCh at 10 Gbps
8 OCh at 40 Gbps
9 OCh at 100 Gbps
10~19 Reserved (for future use)
20 ODU0 (i.e., 1.25 Gbps)
21~30 Reserved (for future use)
31 ODU2e (i.e., 10Gbps for FC1200 and GE LAN)
32 ODUflex(GFP) (i.e., 1.25*N Gbps)
33 ODUflex(CBR) (i.e., 1.25*N Gbps)
34~255 Reserved (for future use)
In case of ODUflex(CBR), the Bit_Rate and Tolerance fields are used
together to represent the actual bandwidth of ODUflex, where:
Zhang Expires September 2011 [Page 5]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
- The Bit_Rate field indicates the nominal bit rate of ODUflex(CBR)
encoded as a 32-bit IEEE single-precision floating-point number
(referring to [RFC4506] and [IEEE]).
- The Tolerance field indicates the bit rate tolerance (part per
million, ppm) of the ODUflex(CBR) encoded as an unsigned integer,
which is bounded in 0~100ppm.
For example, for an ODUflex(CBR) service with Bit_Rate = 2.5Gbps and
Tolerance = 100ppm, the actual bandwidth of the ODUflex is:
2.5Gbps * (1 - 100ppm) ~ 2.5Gbps * (1 + 100ppm)
In case of other ODUk signal types, the Bit_Rate and Tolerance fields
are not necessary and MUST be filled with 0.
The usage of the NMC, NVC and Multiplier (MT) fields are the same as
[RFC4328].
4.1. Usage of ODUflex(CBR) Traffic Parameter
In case of ODUflex(CBR), the information of Bit_Rate and Tolerance in
the ODUflex traffic parameter is used to determine the total number
of tributary slots N in the HO ODUk link to be reserved. Here:
N = Ceiling of
ODUflex(CBR) nominal bit rate * (1 + ODUflex(CBR) bit rate tolerance)
---------------------------------------------------------------------
ODTUk.ts nominal bit rate * (1 - HO OPUk bit rate tolerance)
Therefore, a node receiving a Path message containing ODUflex(CBR)
traffic parameter can allocate precise number of tributary slots and
set up the cross-connection for the ODUflex service.
The table below shows the actual bandwidth of the tributary slot of
ODUk (in Gbps), referring to [G709-V3].
ODUk Minimum Nominal Maximum
-------------------------------------------------------
ODU2 1.249 384 632 1.249 409 620 1.249 434 608
ODU3 1.254 678 635 1.254 703 729 1.254 728 823
ODU4 1.301 683 217 1.301 709 251 1.301 735 285
Zhang Expires September 2011 [Page 6]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
Note that:
Minimum bandwidth of ODUTk.ts =
ODTUk.ts nominal bit rate * (1 - HO OPUk bit rate tolerance)
Maximum bandwidth of ODTUk.ts =
ODTUk.ts nominal bit rate * (1 + HO OPUk bit rate tolerance)
Where: HO OPUk bit rate tolerance = 20ppm
For different ODUk, the bandwidths of the tributary slot are
different, and so the total number of tributary slots to be reserved
for the ODUflex(CBR) may not be the same on different HO ODUk links.
This is why the traffic parameter should bring the actual bandwidth
information other than the NMC field.
4.2. Example of ODUflex(CBR) Traffic Parameter
This section gives an example to illustrate the usage of ODUflex(CBR)
traffic parameter.
As shown in Figure 1, assume there is an ODUflex(CBR) service
requesting a bandwidth of (2.5Gbps, +/-100ppm) from node A to node C.
In other words, the ODUflex traffic parameter indicates that Signal
Type is 33 (ODUflex(CBR)), Bit_Rate is 2.5Gbps and Tolerance is
100ppm.
+-----+ +---------+ +-----+
| +-------------+ +-----+ +-------------+ |
| +=============+\| ODU |/+=============+ |
| +=============+/| flex+-+=============+ |
| +-------------+ | |\+=============+ |
| +-------------+ +-----+ +-------------+ |
| | | | | |
| | ....... | | ....... | |
| A +-------------+ B +-------------+ C |
+-----+ HO ODU4 +---------+ HO ODU2 +-----+
=========: TS occupied by ODUflex
---------: free TS
Figure 1 - Example of ODUflex(CBR) Traffic Parameter
Zhang Expires September 2011 [Page 7]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
- On the HO ODU4 link between node A and B:
The maximum bandwidth of the ODUflex equals 2.5Gbps * (1 +
100ppm), and the minimum bandwidth of the tributary slot of ODU4
equals 1.301 683 217Gbps, so the total number of tributary slots
N1 to be reserved on this link is:
N1 = ceiling (2.5Gbps * (1 + 100ppm) / 1.301 683 217) = 2
- On the HO ODU2 link between node B and C:
The maximum bandwidth of the ODUflex equals 2.5Gbps * (1 +
100ppm), and the minimum bandwidth of the tributary slot of ODU2
equals 1.249 384 632Gbps, so the total number of tributary slots
N2 to be reserved on this link is:
N2 = ceiling (2.5Gbps * (1 + 100ppm) / 1.249 384 632) = 3
5. Generalized Label
[RFC3471] has defined the Generalized Label which extends the
traditional label by allowing the representation of not only labels
which travel in-band with associated data packets, but also labels
which identify time-slots, wavelengths, or space division multiplexed
positions. The format of the corresponding RSVP-TE Generalized Label
object is defined in the Section 2.3 of [RFC3473].
However, for different technologies, we usually need use specific
label rather than the Generalized Label. For example, the label
format described in [RFC4606] could be used for SDH/SONET, the label
format in [RFC4328] for G.709.
In this document, a new ODUk label format is defined, the information
model of which is described in Section 4.10 of [OTN-info].
5.1. New definition of ODUk Label
In order to be compatible with new types of ODU signal and new types
of tributary slot, the following new ODUk label format is defined:
Zhang Expires September 2011 [Page 8]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ODUj |OD(T)Uk| T | Reserved | TPN |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Bit Map ......... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
ODUj and OD(T)Uk (4 bits respectively): indicate that LO ODUj is
multiplexed into HO ODUk(k>j), or LO ODUj is mapped into OTUk (j=k).
ODUj field Signal type
---------- -----------
0 LO ODU0
1 LO ODU1
2 LO ODU2
3 LO ODU3
4 LO ODU4
5 LO ODU2e
6 LO ODUflex
7-15 Reserved (for future use)
OD(T)Uk field Signal type
------------- -----------
0 Reserved (for future use)
1 HO ODU1 / OTU1
2 HO ODU2 / OTU2
3 HO ODU3 / OTU3
4 HO ODU4 / OTU4
5-15 Reserved (for future use)
T (2 bits): indicates the type of tributary slot of HO ODUk when LO
ODUj is multiplexed into the HO ODUk (j<k). Currently, two types of
tributary slot are defined in [G709-V3], the 1.25Gbps tributary slot
and the 2.5Gbps tributary slot.
T field TS type
------- -------
0 1.25Gbps TS granularity
1 2.5Gbps TS granularity
2-3 Reserved (for future use)
Zhang Expires September 2011 [Page 9]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
In case of LO ODUj mapped into OTUk (j=k), this field is not
necessary and should be ignored.
TPN (16 bits): indicates the Tributary Port Number (TPN) for the
assigned Tributary Slot(s).
- In case of LO ODUj multiplexed into HO ODU1/ODU2/ODU3, only the
lower 6 bits of TPN field is significant and the other bits of
TPN MUST be set to 0.
- In case of LO ODUj multiplexed into HO ODU4, only the lower 7
bits of TPN field is significant and the other bits of TPN MUST
be set to 0.
- In case of ODUj mapped into OTUk (j=k), the TPN is not needed
and this field MUST be set to 0.
As per [G709-V3], The TPN is used to allow for correct demultiplexing
in the data plane. When an LO ODUj is multiplexed into HO ODUk
occupying one or more TSs, a new TPN value is configured at the two
end of the HO ODUk link and is put into the related MSI byte(s) in
the OPUk overhead at the (traffic) ingress end of the link, so that
the other end of the link can learn which TS(s) is/are used by the LO
ODUj in the data plane.
According to [G709-V3], the rules of TPN assignment should be as the
following tables:
Table 1 - TPN Assignment Rules (2.5Gbps TS granularity)
+-------+-------+----+----------------------------------------------+
|HO ODUk|LO ODUj|TPN | TPN Assignment Rules |
+-------+-------+----+----------------------------------------------+
| ODU2 | ODU1 |1~4 |Fixed, = TS# occupied by ODU1 |
+-------+-------+----+----------------------------------------------+
| | ODU1 |1~16|Fixed, = TS# occupied by ODU1 |
| ODU3 +-------+----+----------------------------------------------+
| | ODU2 |1~4 |Flexible, != other existing LO ODU2s' TPNs |
+-------+-------+----+----------------------------------------------+
Zhang Expires September 2011 [Page 10]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
Table 2 - TPN Assignment Rules (1.25Gbps TS granularity)
+-------+-------+----+----------------------------------------------+
|HO ODUk|LO ODUj|TPN | TPN Assignment Rules |
+-------+-------+----+----------------------------------------------+
| ODU1 | ODU0 |1~2 |Fixed, = TS# occupied by ODU0 |
+-------+-------+----+----------------------------------------------+
| | ODU1 |1~4 |Flexible, != other existing LO ODU1s' TPNs |
| ODU2 +-------+----+----------------------------------------------+
| |ODU0 & |1~8 |Flexible, != other existing LO ODU0s and |
| |ODUflex| |ODUflexes' TPNs |
+-------+-------+----+----------------------------------------------+
| | ODU1 |1~16|Flexible, != other existing LO ODU1s' TPNs |
| +-------+----+----------------------------------------------+
| | ODU2 |1~4 |Flexible, != other existing LO ODU2s' TPNs |
| ODU3 +-------+----+----------------------------------------------+
| |ODU0 & | |Flexible, != other existing LO ODU0s and |
| |ODU2e &|1~32|ODU2es and ODUflexes' TPNs |
| |ODUflex| | |
+-------+-------+----+----------------------------------------------+
| ODU4 |Any ODU|1~80|Flexible, != ANY other existing LO ODUs' TPNs |
+-------+-------+----+----------------------------------------------+
Note that in the case of "Flexible", the value of TPN is not relevant
to the TS number as per [G709-V3].
Bit Map (variable): indicates which tributary slots in HO ODUk that
the LO ODUj will be multiplexed into. The sequence of the Bit Map is
consistent with the sequence of the tributary slots in HO ODUk. Each
bit in the bit map represents the corresponding tributary slot in HO
ODUk with a value of 1 or 0 indicating whether the tributary slot
will be used by LO ODUj or not.
The size of the bit map equals to the total number of the tributary
slots of HO ODUk, which is deduced by the ODU(T)k and T fields.
In case of an ODUk mapped into OTUk, it's no need to indicate which
tributary slots will be used, so the size of Bit Map is 0.
Padded bits are added behind the Bit Map to make the whole label a
multiple of four bytes if necessary. Padded bit MUST be set to 0 and
MUST be ignored.
Zhang Expires September 2011 [Page 11]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
5.2. Examples
The following examples are given in order to illustrate the label
format described in the previous sections of this document.
(1) ODUk into OTUk mapping:
In such conditions, the downstream node along an LSP returns a label
indicating that the ODU1 (ODU2 or ODU3 or ODU4) is directly mapped
into the corresponding OTU1 (OTU2 or OTU3 or ODU4). The following
example label indicates an ODU1 mapped into OTU1.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0 0 0 1|0 0 0 1|0 0| Reserved | All 0s |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(2) ODUj into ODUk multiplexing:
In such conditions, this label indicates that an ODUj is multiplexed
into several tributary slots of OPUk and then mapped into OTUk. Some
instances are shown as follow:
- ODU0 into ODU2 Multiplexing:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0 0 0 0|0 0 1 0|0 0| Reserved | TPN = 2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0 1 0 0 0 0 0 0| Padded Bits (0) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
This above label indicates an ODU0 multiplexed into the second
tributary slot of ODU2, wherein the type of the tributary slot is
1.25Gbps, and the TPN value is 2.
- ODU1 into ODU2 Multiplexing with 1.25Gbps TS granularity:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0 0 0 1|0 0 1 0|0 0| Reserved | TPN = 1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0 1 0 1 0 0 0 0| Padded Bits (0) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Zhang Expires September 2011 [Page 12]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
This above label indicates an ODU1 multiplexed into the 2nd and the
4th tributary slot of ODU2, wherein the type of the tributary slot is
1.25Gbps, and the TPN value is 1.
- ODU2 into ODU3 Multiplexing with 2.5Gbps TS granularity:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0 0 1 0|0 0 1 1|0 1| Reserved | TPN = 1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0 1 1 0 1 0 1 0 0 0 0 0 0 0 0 0| Padded Bits (0) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
This above label indicates an ODU2 multiplexed into the 2nd, 3rd, 5th
and 7th tributary slot of ODU3, wherein the type of the tributary
slot is 2.5Gbps, and the TPN value is 1.
5.3. Label Distribution Procedure
This document does not change the existing label distribution
procedures [RFC4328] for GMPLS except that the new ODUk label should
be processed as follows.
When a node receives a generalized label request for setting up an
ODUj LSP from its upstream neighbor node, the node should generate an
ODU label according to the signal type of the requested LSP and the
free resources (i.e., free tributary slots of ODUk) that will be
reserved for the LSP, and send the label to its upstream neighbor
node.
In case of ODUj to ODUk multiplexing, the node should firstly
determine the size of the Bit Map field according to the signal type
and the tributary slot type of ODUk, and then set the bits to 1 in
the Bit Map field corresponding to the reserved tributary slots. The
node should also assign a valid TPN, which does not collided with
other TPN value used by existing LO ODU connections in the selected
HO ODU link, and configure the expected multiplex structure
identifier (ExMSI) using this TPN. Then, the assigned TPN is filled
into the label.
In case of ODUk to OTUk mapping, the node only needs to fill the ODUj
and the ODUk fields with corresponding values in the label. Other
bits are reserved and MUST be set to 0.
Zhang Expires September 2011 [Page 13]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
When receiving an ODU label from its downstream neighbor node, the
node should learn which ODU signal type is multiplexed or mapped into
which ODU signal type by analyzing the ODUj and the ODUk fields.
In case of ODUj to ODUk multiplexing, the node should firstly
determine the size of the Bit Map field according to the signal type
and the tributary slot type of ODUk, and then obtain which tributary
slots in ODUk are reserved by its downstream neighbor node according
to the position of the bits that are set to 1 in the Bit Map field,
so that the node can multiplex the ODUj into the reserved tributary
slots of ODUk after the LSP is established. The node should also get
the TPN value assigned by its downstream neighbor node from the label,
and fill the TPN into the related MSI byte(s) in the OPUk overhead in
the data plane, so that the downstream neighbor node can check
whether the TPN received from the data plane is consistent with the
ExMSI and determine whether there is any mismatch defect.
In case of ODUk to OTUk mapping, the size of Bit Map field is 0 and
no additional procedure is needed.
Note that the procedures of other label related objects (e.g.,
Upstream Label, Label Set) are similar as described above.
Note also that the TPN in the label_ERO may not be assigned (i.e.,
TPN field = 0) if the TPN is requested to be assigned locally.
5.3.1. Notification on Label Error
When receiving an ODUk label from the neighbor node, the node should
check the integrity of the label. An error message containing an
"Unacceptable label value" indication ([RFC3209]) should be sent if
one of the following cases occurs:
- The ODUj field does not match with the Traffic Parameters;
- The OD(T)Uk field does not match with the type of the selected
link;
- The selected link only supports 2.5Gbps TS granularity while the T
field in the label indicates the 1.25Gbps TS granularity;
- The label includes an invalid TPN value that breaks the TPN
assignment rules;
- Not enough bits of Bit Map, or Bit Map with non-zero padding bits;
Zhang Expires September 2011 [Page 14]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
- The reserved resources (i.e., the number of "1" in the Bit Map
field) do not match with the Traffic Parameters.
5.4. Supporting Virtual Concatenation and Multiplication
As per [VCAT], the VCGs can be created using Co-Signaled style or
Multiple LSPs style.
In case of Co-Signaled style, the explicit ordered list of all labels
reflects the order of VCG members, which is similar to [RFC4328]. In
case of multiplexed virtually concatenated signals (NVC > 1), the
first label indicates the components of the first virtually
concatenated signal; the second label indicates the components of the
second virtually concatenated signal; and so on. In case of
multiplication of multiplexed virtually concatenated signals (MT > 1),
the first label indicates the components of the first multiplexed
virtually concatenated signal; the second label indicates components
of the second multiplexed virtually concatenated signal; and so on.
In case of Multiple LSPs style, multiple control plane LSPs are
created with a single VCG and the VCAT Call can be used to associate
the control plane LSPs. The procedures are similar to section 6 of
[VCAT].
5.5. Supporting Multiplexing Hierarchy
As described in [OTN-FRWK], one ODUj connection can be nested into
another ODUk (j<k) connection, which forms the multiplexing hierarchy
in the ODU layer. This is useful if there are some intermediate nodes
in the network which only support ODUk but not ODUj switching.
For example, in Figure 2, assume that N3 is a legacy node which only
supports [G709-V1] and does not support ODU0 switching. If an ODU0
connection between N1 and N5 is required, then we can create an ODU2
connection between N2 and N4 (or ODU1 / ODU3 connection, depending on
policies and the capabilities of the two ends of the connection), and
nest the ODU0 into the ODU2 connection. In this way, N3 only needs to
perform ODU2 switching and does not need to be aware of the inner
ODU0.
Zhang Expires September 2011 [Page 15]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
| |
|<------------------- ODU0 Connection -------------------->|
| | | |
| |<---- ODU2 Connection ----->| |
| | | |
+----+ +----+ +----+ +----+ +----+
| N1 +---------+ N2 +=========+ N3 +=========+ N4 +---------+ N5 |
+----+ +----+ +----+ +----+ +----+
ODU3 link ODU3 link ODU3 link ODU3 link
Figure 2 - Example of multiplexing hierarchy
The control plane signaling should support the provisioning of
hierarchical multiplexing. Two methods are provided below (taking
Figure 2 as example):
- The outer ODU2 connection is created in advance based on network
planning, which is treated as a Forwarding Adjacency (FA). Then
the inner ODU0 can be created using the resource of the ODU2 FA.
In this case, the outer ODU2 and inner ODU0 connections are
created separately, and the normal ODU connection creation
procedure described in this document can be used.
- Using the multi-layer network signaling described in [RFC4206],
[RFC6107] and [RFC6001] (including related modifications, if
needed). That is, when the signaling message for ODUO connection
arrives at N2, a new RSVP session between N2 and N4 is triggered
to create the ODU2 connection. This ODU2 connection is treated as
an FA after it is created. And then the signaling procedure for
the ODU0 connection can be continued using the resource of the
ODU2 FA.
5.6. Control Plane Backward Compatibility Considerations
Since the [RFC4328] has been deployed in the network for the nodes
that support [G709-V1] (herein we call them "legacy nodes"), backward
compatibility SHOULD be taken into consideration when the new nodes
(i.e., nodes that support [G709-V3]) and the legacy nodes are
interworking.
For backward compatibility consideration, the new node SHOULD have
the ability to generate and parse legacy labels.
Zhang Expires September 2011 [Page 16]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
o For the legacy node, it always generates and sends legacy label to
its upstream node, no matter the upstream node is new or legacy,
as described in [RFC4328].
o For the new node, it will generate and send legacy label if its
upstream node is a legacy one, and generate and send new label if
its upstream node is a new one.
One backwards compatibility example is shown in Figure 3:
Path Path Path Path
+-----+ ----> +-----+ ----> +------+ ----> +------+ ----> +-----+
| | | | | | | | | |
| A +-------+ B +-------+ C +-------+ D +-------+ E |
| new | | new | |legacy| |legacy| | new |
+-----+ <---- +-----+ <---- +------+ <---- +------+ <---- +-----+
Resv Resv Resv Resv
(new label) (legacy label) (legacy label) (legacy label)
Figure 3 - Backwards compatibility example
As described above, for backward compatibility considerations, it is
necessary for a new node to know whether the neighbor node is new or
legacy.
One optional method is manual configuration. But it is recommended to
use LMP to discover the capability of the neighbor node automatically,
as described in [OTN-LMP].
When performing the HO ODU link capability negotiation:
o If the neighbor node only support the 2.5Gbps TS and only support
ODU1/ODU2/ODU3, the neighbor node should be treated as a legacy
node.
o If the neighbor node can support the 1.25Gbps TS, or can support
other LO ODU types defined in [G709-V3]), the neighbor node should
be treated as new node.
o If the neighbor node returns a LinkSummaryNack message including
an ERROR_CODE indicating nonsupport of HO ODU link capability
negotiation, the neighbor node should be treated as a legacy node.
Zhang Expires September 2011 [Page 17]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
6. Security Considerations
This document introduces no new security considerations to the
existing GMPLS signaling protocols. Referring to [RFC3473], further
details of the specific security measures are provided. Additionally,
[GMPLS-SEC] provides an overview of security vulnerabilities and
protection mechanisms for the GMPLS control plane.
7. IANA Considerations
- G.709 SENDER_TSPEC and FLOWSPEC objects:
The traffic parameters, which are carried in the G.709
SENDER_TSPEC and FLOWSPEC objects, do not require any new object
class and type based on [RFC4328]:
o G.709 SENDER_TSPEC Object: Class = 12, C-Type = 5 [RFC4328]
o G.709 FLOWSPEC Object: Class = 9, C-Type = 5 [RFC4328]
- Generalized Label Object:
The new defined ODU label (session 5) is a kind of generalized
label. Therefore, the Class-Num and C-Type of the ODU label is
the same as that of generalized label described in [RFC3473],
i.e., Class-Num = 16, C-Type = 2.
8. References
8.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC4328] D. Papadimitriou, Ed. "Generalized Multi-Protocol Label
Switching (GMPLS) Signaling Extensions for G.709 Optical
Transport Networks Control", RFC 4328, Jan 2006.
[RFC3209] D. Awduche et al, "RSVP-TE: Extensions to RSVP for LSP
Tunnels", RFC3209, December 2001.
Zhang Expires September 2011 [Page 18]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
[RFC3471] Berger, L., Editor, "Generalized Multi-Protocol Label
Switching (GMPLS) Signaling Functional Description", RFC
3471, January 2003.
[RFC3473] L. Berger, Ed., "Generalized Multi-Protocol Label Switching
(GMPLS) Signaling Resource ReserVation Protocol-Traffic
Engineering (RSVP-TE) Extensions", RFC 3473, January 2003.
[RFC3945] Mannie, E., "Generalized Multi-Protocol Label Switching
(GMPLS) Architecture", RFC 3945, October 2004.
[VCAT] G. Bernstein et al, "Operating Virtual Concatenation (VCAT)
and the Link Capacity Adjustment Scheme (LCAS) with
Generalized Multi-Protocol Label Switching (GMPLS)", draft-
ietf-ccamp-gmpls-vcat-lcas-11.txt, March 9, 2011.
[RFC4206] K. Kompella, Y. Rekhter, Ed., " Label Switched Paths (LSP)
Hierarchy with Generalized Multi-Protocol Label Switching
(GMPLS) Traffic Engineering (TE)", RFC 4206, October 2005.
[RFC6107] K. Shiomoto, A. Farrel, "Procedures for Dynamically
Signaled Hierarchical Label Switched Paths", RFC6107,
February 2011.
[RFC6001] Dimitri Papadimitriou et al, "Generalized Multi-Protocol
Label Switching (GMPLS) Protocol Extensions for Multi-Layer
and Multi-Region Networks (MLN/MRN)", RFC6001, February 21,
2010.
[OTN-frwk] Fatai Zhang et al, "Framework for GMPLS and PCE Control of
G.709 Optical Transport Networks", draft-ietf-ccamp-gmpls-
g709-framework-02.txt, July 12, 2010.
[OTN-info] S. Belotti et al, "Information model for G.709 Optical
Transport Networks (OTN)", draft-bccg-ccamp-otn-g709-info-
model-03.txt, Oct 18, 2010.
[OTN-LMP] Fatai Zhang, Ed., "Link Management Protocol (LMP)
extensions for G.709 Optical Transport Networks", draft-
zhang-ccamp-gmpls-g.709-lmp-discovery-03.txt, May 13, 2010.
[G709-V3] ITU-T, "Interfaces for the Optical Transport Network (OTN)
", G.709/Y.1331, December 2009.
Zhang Expires September 2011 [Page 19]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
8.2. Informative References
[G709-V1] ITU-T, "Interface for the Optical Transport Network (OTN),"
G.709 Recommendation (and Amendment 1), February 2001
(November 2001).
[G709-V2] ITU-T, "Interface for the Optical Transport Network (OTN),"
G.709 Recommendation, March 2003.
[G798-V2] ITU-T, "Characteristics of optical transport network
hierarchy equipment functional blocks", G.798, December
2006.
[G798-V3] ITU-T, "Characteristics of optical transport network
hierarchy equipment functional blocks", G.798v3, consented
June 2010.
[RFC4506] M. Eisler, Ed., "XDR: External Data Representation
Standard", RFC 4506, May 2006.
[IEEE] "IEEE Standard for Binary Floating-Point Arithmetic",
ANSI/IEEE Standard 754-1985, Institute of Electrical and
Electronics Engineers, August 1985.
[GMPLS-SEC] Fang, L., Ed., "Security Framework for MPLS and GMPLS
Networks", Work in Progress, October 2009.
9. Authors' Addresses
Fatai Zhang
Huawei Technologies
F3-5-B R&D Center, Huawei Base
Bantian, Longgang District
Shenzhen 518129 P.R.China
Phone: +86-755-28972912
Email: zhangfatai@huawei.com
Guoying Zhang
China Academy of Telecommunication Research of MII
11 Yue Tan Nan Jie Beijing, P.R.China
Phone: +86-10-68094272
Email: zhangguoying@mail.ritt.com.cn
Zhang Expires September 2011 [Page 20]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
Sergio Belotti
Alcatel-Lucent
Optics CTO
Via Trento 30 20059 Vimercate (Milano) Italy
+39 039 6863033
Email: sergio.belotti@alcatel-lucent.it
Daniele Ceccarelli
Ericsson
Via A. Negrone 1/A
Genova - Sestri Ponente
Italy
Email: daniele.ceccarelli@ericsson.com
Yi Lin
Huawei Technologies
F3-5-B R&D Center, Huawei Base
Bantian, Longgang District
Shenzhen 518129 P.R.China
Phone: +86-755-28972914
Email: yi.lin@huawei.com
Yunbin Xu
China Academy of Telecommunication Research of MII
11 Yue Tan Nan Jie Beijing, P.R.China
Phone: +86-10-68094134
Email: xuyunbin@mail.ritt.com.cn
Pietro Grandi
Alcatel-Lucent
Optics CTO
Via Trento 30 20059 Vimercate (Milano) Italy
+39 039 6864930
Email: pietro_vittorio.grandi@alcatel-lucent.it
Zhang Expires September 2011 [Page 21]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
Diego Caviglia
Ericsson
Via A. Negrone 1/A
Genova - Sestri Ponente
Italy
Email: diego.caviglia@ericsson.com
Acknowledgment
This document was prepared using 2-Word-v2.0.template.dot.
Intellectual Property
The IETF Trust takes no position regarding the validity or scope of
any Intellectual Property Rights or other rights that might be
claimed to pertain to the implementation or use of the technology
described in any IETF Document or the extent to which any license
under such rights might or might not be available; nor does it
represent that it has made any independent effort to identify any
such rights.
Copies of Intellectual Property disclosures made to the IETF
Secretariat and any assurances of licenses to be made available, or
the result of an attempt made to obtain a general license or
permission for the use of such proprietary rights by implementers or
users of this specification can be obtained from the IETF on-line IPR
repository at http://www.ietf.org/ipr
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
any standard or specification contained in an IETF Document. Please
address the information to the IETF at ietf-ipr@ietf.org.
The definitive version of an IETF Document is that published by, or
under the auspices of, the IETF. Versions of IETF Documents that are
published by third parties, including those that are translated into
other languages, should not be considered to be definitive versions
of IETF Documents. The definitive version of these Legal Provisions
is that published by, or under the auspices of, the IETF. Versions of
these Legal Provisions that are published by third parties, including
Zhang Expires September 2011 [Page 22]
draft-zhang-ccamp-gmpls-evolving-g709-07.txt March 2011
those that are translated into other languages, should not be
considered to be definitive versions of these Legal Provisions.
For the avoidance of doubt, each Contributor to the IETF Standards
Process licenses each Contribution that he or she makes as part of
the IETF Standards Process to the IETF Trust pursuant to the
provisions of RFC 5378. No language to the contrary, or terms,
conditions or rights that differ from or are inconsistent with the
rights and licenses granted under RFC 5378, shall have any effect and
shall be null and void, whether published or posted by such
Contributor, or included with or in such Contribution.
Disclaimer of Validity
All IETF Documents and the information contained therein are provided
on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE
REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE
IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY
WARRANTY THAT THE USE OF THE INFORMATION THEREIN WILL NOT INFRINGE
ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE.
Copyright Notice
Copyright (c) 2010 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Zhang Expires September 2011 [Page 23]
| PAFTECH AB 2003-2026 | 2026-04-24 04:17:28 |