One document matched: draft-wijnands-mpls-mldp-csc-01.txt
Differences from draft-wijnands-mpls-mldp-csc-00.txt
Network Working Group IJsbrand Wijnands
Internet Draft Eric C. Rosen
Intended Status: Proposed Standard Cisco Systems, Inc.
Expires: October 6, 2009
Maria Napierala
AT&T
April 6, 2009
Using mLDP through a Backbone where there is no Route to the Root
draft-wijnands-mpls-mldp-csc-01.txt
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Copyright and License Notice
Copyright (c) 2009 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents in effect on the date of
publication of this document (http://trustee.ietf.org/license-info).
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document.
Wijnands, et al. [Page 1]
Internet Draft draft-wijnands-mpls-mldp-csc-01.txt April 2009
Abstract
The control protocol used for constructing Point-to-Multipoint and
Multipoint-to-Multipoint Label Switched Paths ("MP LSPs") contains a
field that identifies the address of a "root node". Intermediate
nodes are expected to be able to look up that address in their
routing tables. However, if the route to the root node is a BGP
route, and the intermediate nodes are part of a BGP-free core, this
is not possible. This document specifies procedures which enable a
MP LSP to be constructed through a BGP-free core. In these
procedures, the root node address is temporarily replaced by an
address which is known to the intermediate nodes.
Table of Contents
1 Introduction .......................................... 3
2 The Recursive Opaque Value Type ....................... 5
2.1 Encoding .............................................. 5
2.2 Procedures ............................................ 5
3 The VPN-Recursive MP FEC Element ...................... 6
3.1 Encoding .............................................. 6
3.2 Procedures ............................................ 7
4 IANA Considerations ................................... 7
5 Security Considerations ............................... 8
6 Acknowledgments ....................................... 8
7 Authors' Addresses .................................... 8
8 Normative References .................................. 9
Wijnands, et al. [Page 2]
Internet Draft draft-wijnands-mpls-mldp-csc-01.txt April 2009
1. Introduction
[MLDP] defines several LDP FEC element encodings: P2MP, MP2MP
Upstream, and MP2MP Downstream.
The encoding for these three FEC elements is shown in Figure 1.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Address Family | Address Length|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ Root Node Address ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Opaque Length | . |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
~ ~
| Opaque Value |
| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
MLDP FEC Element Encoding
Figure 1
Note that a P2MP or MP2MP label switched path ("MP LSP") is
identified by the combination of a "root node" and a variable length
"opaque value". The root node also plays a special role in the MLDP
procedures - MLDP messages that are "about" a particular MP LSP are
forwarded to the LDP adjacency that is the next hop on the route to
the root node.
Sometimes it is desirable for a MP LSP to pass through a part of the
network in which there is no route to the root node. For instance,
consider the following topology:
CE1----PE1---P1---- ...----P2 ----PE2----CE2----R
Figure 2
where CE1 and CE2 are "customer edge routers", PE1 and PE2 are
"provider edge routers", but the provider's core is "BGP-free". That
is, PE1 has a BGP-learned route for R, in which PE2 is the BGP next
hop. However, the provider's interior routers (such as P1 and P2) do
not have any BGP-learned routes, and in particular do not have any
Wijnands, et al. [Page 3]
Internet Draft draft-wijnands-mpls-mldp-csc-01.txt April 2009
routes to R.
In such an environment, data packets from CE1 address to R would get
encapsulated by PE1, tunneled to PE2, decapsulated by PE2, and
forwarded to CE2.
Suppose now that CE1 is trying to set up a MP LSP whose root is R,
and the intention is that the provider's network will participate in
the construction of the LSP. Then the MLDP messages identifying the
LSP must be passed from CE1 to PE1, from PE1 to P1, ..., from P2 to
PE2, from PE2 to CE2, and from CE2 to R.
To begin the process, CE1 creates a MP FEC element with the address
of R as the root node address, and passes that FEC element via MLDP
to PE1. However, PE1 cannot use this same FEC element to identify
the LSP in the LDP messages it sends to P1, because P1 does not have
a route to R.
However, PE1 does know that PE2 is the "BGP next hop" on the path to
R. What is needed is a method whereby:
- PE1 can tell P1 to set up an LSP as if the root node were PE2,
and
- PE2 can determine that the LSP in question is really rooted at R,
not at PE2 itself,
- PE2 can determine the original FEC element that CE1 passed to
PE1, so that PE2 can pass it on to CE2.
This document defines the procedures that allow CE1 to create an LSP
rooted at R. These procedures require PE1 to modify the MP FEC
element before sending an MLDP message to P1, and they also require
PE2 to modify the MP FEC element before sending an MLDP message to
CE2.
A slight variation on these procedures, also specified in this
document, provides mLDP support for "Carrier's Carrier" MVPN service
[VPN, MVPN].
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
Wijnands, et al. [Page 4]
Internet Draft draft-wijnands-mpls-mldp-csc-01.txt April 2009
2. The Recursive Opaque Value Type
2.1. Encoding
We define a new Opaque Value Type, the Recursive Opaque Value Type.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 6 | Length | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
~ ~
| P2MP or MP2MP FEC Element |
| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Recursive Opaque Value Type
Figure 3
The "opaque value" itself is a P2MP or MP2MP FEC element, encoded
exactly as specified in [MLDP], with a type field, a length field,
and value field of is own. The length field of the Recursive Opaque
Value Type thus includes the type and length fields of the FEC
element that is the value field.
2.2. Procedures
In the topology of Figure 2, let us suppose that CE1 sends PE1 an MP
FEC element whose root node is R, and whose opaque value is Q. We
will refer to this FEC element as "CE1-FEC".
PE1 determines that the root node R matches a BGP route, with a BGP
next hop of PE2. PE1 also knows by its configuration that the
interior routers on the path to PE2 are "BGP-free", and thus have no
route to R.
PE1 therefore MUST create a new MP FEC element, whose root node
address is the address of PE2, and whose opaque value is a type 6 FEC
element whose value field contains CE1-FEC. We refer to this FEC
element as PE2-FEC. PE1 then MUST send this FEC element to P1.
As far as the interior routers are concerned, they are being
requested to build a MP LSP whose root node is PE2. They MUST NOT
interpret the opaque value at all.
Wijnands, et al. [Page 5]
Internet Draft draft-wijnands-mpls-mldp-csc-01.txt April 2009
When PE2-FEC arrives at PE2, PE2 notes that it is the identified root
node, and that the opaque value is a type 6 opaque value. Therefore
it MUST replace PE2-FEC with the contents of the type 6 opaque value
(i.e., with CE1-FEC) before doing any further processing. This will
result in CE1-FEC being sent on to CE2, and presumably further from
CE2 to R.
3. The VPN-Recursive MP FEC Element
3.1. Encoding
We define a new Opaque Value Type, the VPN-Recursive Opaque Value
Type.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 7 | Length | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
| |
| Route Distinguisher (8 octets) +-+-+-+-+-+-+-+-+
| | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
~ ~
| P2MP or MP2MP FEC Element |
| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
VPN-Recursive Opaque Value Type
Figure 4
The "opaque value" consists of an eight-octet Route Distinguisher
(RD), followed by a P2MP or MP2MP FEC element, encoded exactly as
specified in [MLDP], with a type field, a length field, and value
field of is own. The length field of the Recursive Opaque Value Type
thus includes the 8 octets of RD plus the type and length fields of
the FEC element that is the value field.
Wijnands, et al. [Page 6]
Internet Draft draft-wijnands-mpls-mldp-csc-01.txt April 2009
3.2. Procedures
Referring again to the topology of Figure 2, suppose that PE1/PE2 are
offering "Carrier's Carrier VPN Service" [VPN] to CE1/CE2. CE1 sends
PE1 an MP FEC element whose root node is R, and whose opaque value is
Q. We will refer to this FEC element as "CE1-FEC". However, PE1's
route to R will be in a VRF ("Virtual Routing and Forwarding Table").
Therefore the FEC-element created by PE1 must contain some identifier
that PE2 can use to find the proper VRF in which to look up the
address of R.
When PE1 looks up the address of R in a VRF, it will find a route in
the VPN-IP address family. The next hop will be PE2, but there will
also be a Route Distinguisher (RD) as part of that NLRI of the
matching route. In this case, the new FEC element created by PE1
MUST have the address of PE2 as the root node address, and MUST have
a type 7 opaque value.
The value field of the type 7 opaque value MUST consist of the
8-octet RD followed by CE1-FEC.
As far as the interior routers are concerned, they are being
requested to build a MP LSP whose root node is PE2. They MUST NOT
interpret the opaque value at all.
When PE2-FEC arrives at PE2, PE2 notes that it is the identified root
node, and that the opaque value is a type 7 opaque value. Therefore
it MUST replace PE2-FEC with the contents of the type 7 opaque value
(i.e., with CE1-FEC) before doing any further processing. It also
finds the VRF associated with the identified RD, and MUST use that
VRF to lookup up the path to R. This will result in CE1-FEC being
sent on to CE2, and presumably further from CE2 to R.
4. IANA Considerations
[MLDP] defines a registry for "The LDP MP Opaque Value Element Type".
This document requires the assignment of two new code points in this
registry:
- Type 6.
An opaque value of this type is itself a TLV that encodes an mLDP
FEC type, as defined in [MLDP].
Wijnands, et al. [Page 7]
Internet Draft draft-wijnands-mpls-mldp-csc-01.txt April 2009
- Type 7
An opaque value of this type consists of an eight-octet Route
Distinguisher as defined in [VPN], followed by a TLV that encodes
an mLDP FEC type, as defined in [MLDP].
5. Security Considerations
TBD
6. Acknowledgments
The authors wish to thank Toerless Eckert for his contribution to
this work.
7. Authors' Addresses
IJsbrand Wijnands
Cisco Systems, Inc.
De kleetlaan 6a Diegem 1831
Belgium
E-mail: ice@cisco.com
Eric C. Rosen
Cisco Systems, Inc.
1414 Massachusetts Avenue
Boxborough, MA, 01719
E-mail: erosen@cisco.com
Maria Napierala
AT&T Labs
200 Laurel Avenue, Middletown, NJ 07748
E-mail: mnapierala@att.com
Wijnands, et al. [Page 8]
Internet Draft draft-wijnands-mpls-mldp-csc-01.txt April 2009
8. Normative References
[MLDP] "Label Distribution Protocol Extensions for Point-to-
Multipoint and Multipoint-to-Multipoint Label Switched Paths", Minei,
Kompella, Wijnands, Thomas, draft-ietf-mpls-ldp-p2mp-05.txt, May 2008
[MVPN] "Multicast in MPLS/BGP IP VPNs", Rosen, Aggarwal, et. al.,
draft-ietf-l3vpn-2547bis-mcast-08.txt, March 2009
[RFC2119] "Key words for use in RFCs to Indicate Requirement
Levels.", Bradner, March 1997
[VPN] "BGP/MPLS IP Virtual Private Networks (VPNs)", Rosen, Rekhter,
RFC 4364, February 2006
Wijnands, et al. [Page 9]
| PAFTECH AB 2003-2026 | 2026-04-21 23:01:52 |