One document matched: draft-stewart-behave-sctpnat-03.txt
Differences from draft-stewart-behave-sctpnat-02.txt
Network Working Group R. Stewart
Internet-Draft Cisco Systems, Inc.
Intended status: Standards Track M. Tuexen
Expires: May 20, 2008 Muenster Univ. of Applied Sciences
November 17, 2007
Stream Control Transmission Protocol (SCTP) Network Address Translation
draft-stewart-behave-sctpnat-03.txt
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on May 20, 2008.
Copyright Notice
Copyright (C) The IETF Trust (2007).
Abstract
Stream Control Transmission Protocol [RFC4960] provides a reliable
communications channel between two end-hosts in many ways similar to
TCP [RFC0793]. With the widespread deployment of Network Address
Translators (NAT), specialized code has been added to NAT for TCP
that allows multiple hosts to reside behind a NAT and yet use only a
single globally unique IPv4 address, even when two hosts (behind the
NAT) choose the same port numbers for their connection. This
Stewart & Tuexen Expires May 20, 2008 [Page 1]
Internet-Draft SCTP Network Address Translation November 2007
additional code is sometimes classified as Network Address and Port
Translation or NAPT. To date, specialized code for SCTP has NOT yet
been added to most NAT's so that only pure NAT is available. The end
result of this is that only one SCTP capable host can be behind a
NAT.
This document describes an SCTP specific variant of NAT which
provides similar features of NAPT in the single point traversal
scenario described in [I-D.xie-behave-sctp-nat-cons]. Furthermore
both algorithms are compared.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. The SCTP specific variant of NAT . . . . . . . . . . . . . . . 4
4. Handling of local port number collisions . . . . . . . . . . . 7
5. Handling of local port number and verification tag
collisions and lost state . . . . . . . . . . . . . . . . . . 7
6. Discussion of the SCTP specific variant of NAT . . . . . . . . 8
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 8
8. Security considerations . . . . . . . . . . . . . . . . . . . 8
9. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 9
10. References . . . . . . . . . . . . . . . . . . . . . . . . . . 9
10.1. Normative References . . . . . . . . . . . . . . . . . . 9
10.2. Informative References . . . . . . . . . . . . . . . . . 9
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 9
Intellectual Property and Copyright Statements . . . . . . . . . . 11
Stewart & Tuexen Expires May 20, 2008 [Page 2]
Internet-Draft SCTP Network Address Translation November 2007
1. Introduction
Stream Control Transmission Protocol [RFC4960] provides a reliable
communications channel between two end-hosts in many ways similar to
TCP [RFC0793]. With the widespread deployment of Network Address
Translators (NAT), specialized code has been added to NAT for TCP
that allows multiple hosts to reside behind a NAT and yet use only a
single globally unique IPv4 address, even when both hosts (behind the
NAT) choose the same port numbers for their connection. This
additional code is sometimes classified as Network Address and Port
Translation or NAPT. To date, specialized code for SCTP has NOT yet
been added to most NAT's so that only true NAT is available. The end
result of this is that only one SCTP capable host can be behind a
NAT.
This document proposes an SCTP specific variant NAT that provides the
NAPT functionality without changing SCTP port numbers. The authors
feel it is possible and desirable to make these changes for a number
of reasons.
o It is desirable for SCTP end-hosts on multiple platforms to be
able to share a global IP address behind a NAT, much as TCP does
today.
o If a NAT does not need to change any data within an SCTP packet it
will reduce the processing burden of NAT'ing SCTP by NOT needing
to execute the CRC32c checksum required by SCTP.
o Not having to touch the IP payload makes the processing of ICMP
messages in NATs easier.
2. Terminology
For this discussion we will use several terms. For clarity we will
first define these terms.
o Global-Address - That address that a host behind a NAT is
attempting to contact.
o Global-Port - The port number of the peer process at the Global-
Address.
o Local-Address - The local address that is known to the host behind
the NAT, aka a private address [RFC1918].
o Local-Port - The port number that is in use by the host holding
the Local-Address. Normally this is the port that will be
Stewart & Tuexen Expires May 20, 2008 [Page 3]
Internet-Draft SCTP Network Address Translation November 2007
translated by the NAPT to a different port number.
o Nat-Global-Address - The global address assigned to the NAT box
which it uses as a source address when sending packets towards the
Global-Address.
o Natted-Port - The port number that the NAT is using to represent
the Local-Port when send data packets toward the Global-Address
and Global-Port.
o Local-Vtag - The Verification Tag that the host inside the natted
address space has chosen for its communication. The V-Tag is a
unique 32 bit tag that must accompany any incoming SCTP packet for
this association to the Local-Address.
o Remote-Vtag - The Verification Tag that the host holding the
Global-Address has chosen for its communication. The V-Tag is a
unique 32 bit tag that must accompany any incoming SCTP packet for
this association to the Global-Address.
3. The SCTP specific variant of NAT
In this section we assume that we have multiple SCTP capable hosts
behind a NAT which has one Nat-Global address. Furthermore we are
considering only the single point traversal scenario described in
[I-D.xie-behave-sctp-nat-cons].
The modification of SCTP packets sent to the public Internet is easy.
The source address of the packet has to be replaced with the Nat-
Global-Address. It may also be necessary to establish some state in
the NAT box to handle incoming packets, which is discussed later.
For SCTP packets coming from the public Internet the destination
address of the packets has to be replaced with the Local-Address of
the host the packet has to be delivered to. The lookup of the Local-
Address is based on the Global-VTag, Global-Port, Global-Address,
Local-Vtag and the Local-Port.
For the SCTP NAT processing the NAT box has to maintain a table of
Global-VTag, Global-Port, Global-Address, Local-VTag, Local-Port and
Local-Address. An entry in that table is called a NAT state control
block.
The processing of outgoing SCTP packets containing an INIT-chunk is
described in the following figure.
Stewart & Tuexen Expires May 20, 2008 [Page 4]
Internet-Draft SCTP Network Address Translation November 2007
Local-Network Global-Internet
[From(Local-Address,Local-Port),
To(Global-Address:Global-Port)
INIT(Initiate-Tag)]------->
Create(Global-Port,Global-Address,Initiate-Tag,Local-Port,Local-Address)
Returns(NAT-State control block)
Translate To:
[From(Nat-Global-Address:Local-Port),
To(Global-Address:Global-Port)
INIT(Initiate-Tag)]------->
It should be noted that normally no NAT control block will be
created. However it is possible that that there is already a NAT
control block with the same Global-Port, Global-Address, Initiate-
Tag, Local-VTag but different Local-Address. In this case the INIT
SHOULD be dropped and an ABORT MAY be sent back.
The processing of outgoing SCTP packets containing no INIT-chunk is
described in the following figure.
Local-Network Global-Internet
[From(Local-Address,Local-Port),
To(Global-Address:Global-Port)]------->
Translate To:
[From(Nat-Global-Address:Local-Port),
To(Global-Address:Global-Port)]------->
The processing of incoming SCTP packets containing INIT-ACK chunks is
described in the following figure.
Stewart & Tuexen Expires May 20, 2008 [Page 5]
Internet-Draft SCTP Network Address Translation November 2007
Local-Network Global-Internet
<-----[From(Global-Address,Global-Port),
To(Nat-Global-Address,Local-Port),
SCTP(Local-VTag),
INIT-ACK(Initiate-Tag)]
Lookup(0,Global-Port,Global-Address,Local-VTag,Local-Port)
Update(Initiate-Tag,Global-Port,Global-Address,Local-VTag,Local-Port)
Returns(NAT-State control block containing Local-Address)
<-----[From(Global-Address:Global-Port),
To(Local-Address,Local-Port)
SCTP(Local-VTag)]
In the case Lookup fails, the SCTP packet is dropped. The Update
routine inserts the Global-VTag in the NAT state control block.
The processing of incoming SCTP packets containing and ABORT or
SHUTDOWN-COMLETE chunk with the T-Bit set is described in the
following figure.
Local-Network Global-Internet
<-----[From(Global-Address,Global-Port),
To(Nat-Global-Address,Local-Port),
SCTP(Global-VTag)]
Lookup(Global-VTag,Global-Port,Global-Address,0,Local-Port)
Returns(NAT-State control block containing Local-Address)
<-----[From(Global-Address:Global-Port),
To(Local-Address,Local-Port)
SCTP(Global-VTag)]
The processing of other incoming SCTP packets is described in the
following figure.
Stewart & Tuexen Expires May 20, 2008 [Page 6]
Internet-Draft SCTP Network Address Translation November 2007
Local-Network Global-Internet
<-----[From(Global-Address,Global-Port),
To(Nat-Global-Address,Local-Port),
SCTP(Local-VTag)]
Lookup(0,Global-Port,Global-Address,Local-VTag,Local-Port)
Returns(NAT-State control block contaning Local-Address)
<-----[From(Global-Address:Global-Port),
To(Local-Address,Local-Port)
SCTP(Local-VTag)]
4. Handling of local port number collisions
There is one drawback of the SCTP specific variant of NAT compared to
a NAPT solution like the ones available for TCP. Consider the case
where two hosts in the Local-Address space want to setup an SCTP
association with the same server running on the same host in the
Internet. This means that the Global-Port and the Global-Address are
the same. If they both chose the same Local-Port the server can not
distinguish both associations based on the address and port numbers.
For the server it looks like the association is being restarted. To
overcome this limitation the client sends a NAT_SUPPORTED parameter
in the INIT-chunk which is defined as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0xC007 | Length=4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
When the server receives this parameter it will also use the
verification tag to look up the association. However, this will make
it impossible to restart such associations.
5. Handling of local port number and verification tag collisions and
lost state
Consider the case where two hosts in the Local-Address space want to
setup an SCTP association with the same server running on the same
host in the Internet. This means that the Global-Port and the
Global-Address are the same. If they both chose the same Local-Port
and Local-VTag, the NAT box can not distinguish incoming packets
Stewart & Tuexen Expires May 20, 2008 [Page 7]
Internet-Draft SCTP Network Address Translation November 2007
anymore. But this is very unlikely. The Local-Vtags are chosen by
random and if the Local-Ports are also chosen ephemeral an random
this gives a 46 bit random number which has to match. In the TCP
like NAPT case the NAT box can control the 16 bit Natted Port.
However, if this unlikely happens the NAT box SHOULD respond to the
INIT chunk by sending an ABORT chunk with the M-bit set. The source
address of the ABORT chunk MUST be the destination address of the
SCTP packet containing the INIT chunk.
The ABORT chunk defined in [RFC4960] is therefore extended by using
the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 6 | Reserved |M|T| Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
\ \
/ zero or more Error Causes /
\ \
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
In case the NAT box has to handle an SCTP packet for which it does
not have the necessary state, it SHOULD send an SCTP packet with an
ABORT chunk as descibed above.
6. Discussion of the SCTP specific variant of NAT
The advantages of using the SCTP specific variant of NAT is that the
NAT engines do not have to modify the SCTP packet at all. This is
important because modifying the packets requires a recalculation of
the checksum over the complete packet. There is no way of just
computing the different like it is possible for the IP, UDP and TCP
checksum. It should also be noted that the processing of ICMP
packets is easier.
7. IANA Considerations
TBD
8. Security considerations
State maintenance within a NAT is always a subject of possible Denial
Of Service attack. This document recommends that at a minimum a NAT
Stewart & Tuexen Expires May 20, 2008 [Page 8]
Internet-Draft SCTP Network Address Translation November 2007
run a timer on any SCTP state so that old association state can be
cleaned up.
9. Acknowledgments
The authors wish to thank Henning Peters, Irene Ruengeler for their
invaluable comments.
10. References
10.1. Normative References
[RFC0793] Postel, J., "Transmission Control Protocol", STD 7,
RFC 793, September 1981.
[RFC2026] Bradner, S., "The Internet Standards Process -- Revision
3", BCP 9, RFC 2026, October 1996.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC4960] Stewart, R., "Stream Control Transmission Protocol",
RFC 4960, September 2007.
10.2. Informative References
[RFC1918] Rekhter, Y., Moskowitz, R., Karrenberg, D., Groot, G., and
E. Lear, "Address Allocation for Private Internets",
BCP 5, RFC 1918, February 1996.
[I-D.xie-behave-sctp-nat-cons]
Xie, Q., Stewart, R., Holdrege, M., and M. Tuexen, "SCTP
NAT Traversal Considerations",
draft-xie-behave-sctp-nat-cons-03 (work in progress),
November 2007.
Stewart & Tuexen Expires May 20, 2008 [Page 9]
Internet-Draft SCTP Network Address Translation November 2007
Authors' Addresses
Randall R. Stewart
Cisco Systems, Inc.
4875 Forest Drive
Suite 200
Columbia, SC 29206
USA
Phone:
Email: rrs@cisco.com
Michael Tuexen
Muenster Univ. of Applied Sciences
Stegerwaldstr. 39
48565 Steinfurt
Germany
Email: tuexen@fh-muenster.de
Stewart & Tuexen Expires May 20, 2008 [Page 10]
Internet-Draft SCTP Network Address Translation November 2007
Full Copyright Statement
Copyright (C) The IETF Trust (2007).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgment
Funding for the RFC Editor function is provided by the IETF
Administrative Support Activity (IASA).
Stewart & Tuexen Expires May 20, 2008 [Page 11]
| PAFTECH AB 2003-2026 | 2026-04-23 00:33:08 |