One document matched: draft-shah-l2vpn-arp-mediation-01.txt
Differences from draft-shah-l2vpn-arp-mediation-00.txt
L2VPN Working Group H. Shah Ciena Networks
Internet Draft E. Rosen Cisco Systems
W. Augustyn consultant
July 2004 G. Heron Tellabs
Expires: January 2005 T. Smith Laurel Networks
A. Moranganti Axiowave Networks
S. Khandekar Alcatel
V. Kompella Alcatel
A. Malis Tellabs
S. Wright Bell South
V. Radoaca Nortel Networks
A. Vishwanathan Force10 Networks
ARP Mediation for IP Interworking of Layer 2 VPN
draft-shah-l2vpn-arp-mediation-01.txt
Status of this memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other
documents at any time. It is inappropriate to use Internet-Drafts
as reference material or to cite them other than as "work in
progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Abstract
The VPWS service [L2VPN Framework] provides point-to-point
connections between pairs of Customer Edge (CE) devices. It does
so by binding two Attachment Circuits (each connecting a CE device
with a Provider Edge, PE, device) to a Pseudowire (connecting the
two PEs). In general, the Attachment Circuits must be of the same
technology (e.g., both ethernet, both ATM), and the Pseudowire must
carry the frames of that technology. However, if it is known that
the frames' payload consists solely of IP datagrams, it is possible
to provide a point-to-point connection in which the Pseudowire
connects Attachment Circuits of different technologies. This
requires the PEs to perform a function known as "ARP Mediation".
draft-shah-l2vpn-arp-mediation-04.txt
This document specifies the ARP Mediation function, and specifies
the encapsulation used to carry the IP datagrams on the Pseudowires
when ARP mediation is used.
Table of Contents
1 .0 Introduction..................................................2
2 .0 ARP Mediation (AM) function...................................3
3 .0 IP Layer 2 Interworking Circuits..............................4
4 .0 Discovery of IP Addresses of Locally Attached CE Device.......4
4.1 Monitoring Local Traffic.......................................4
4.2 CE Devices Using ARP...........................................4
4.3 CE Devices Using Inverse ARP...................................6
4.4 CE Devices Using PPP...........................................6
4.5 Proactive method...............................................6
5 .0 IP Address Distribution Between PE............................7
5.1 When To Distribute IP Address..................................7
5.2 LDP Based Distribution.........................................7
5.3 Out-of-band Distribution, Manual Configuration.................8
5.4 Single sided ARP mediation.....................................8
6 .0 How CE Learns The Remote CE's IP address......................9
6.1 CE Devices Using ARP...........................................9
6.2 CE Devices Using Inverse ARP..................................10
6.3 CE Devices Using PPP..........................................10
7 .0 Use of IGPs with IP L2 Interworking L2VPNs...................10
7.1 OSPF..........................................................10
7.2 IS-IS.........................................................11
7.3 RIP...........................................................11
8 .0 Security Considerations......................................12
9 .0 Acknowledgements.............................................12
10 .0 References..................................................12
10.1 Normative References.........................................12
10.2 Informative References.......................................12
11 .0 Authors' Addresses..........................................13
1.0 Introduction
Layer 2 Virtual Private Networks (L2VPN) are constructed with the
use of a Service Provider IP backbone but are presented to the
Customer Edge (CE) devices as Layer 2 networks. In theory, L2VPNs
can carry any Layer 3 protocol, but in many cases, the only Layer 3
protocol is IP. Thus it makes sense to consider procedures that
are either optimized for IP or are outright dedicated to IP traffic
only.
In a typical implementation, illustrated in the diagram below, the
CE devices are connected to the Provider Edge (PE) devices via
Attachment Circuits (AC). The ACs are Layer 2 links. In a pure
L2VPN, if traffic sent from CE1 via AC1 reaches CE2 via AC2, both
ACs would have to be of the same type (i.e., both Ethernet, both
FR, etc.). However, if it is known that only IP traffic will be
Shah, et. al. Expires January 2005 2
draft-shah-l2vpn-arp-mediation-04.txt
carried, the ACs can be of different technologies, provided that
the PEs provide the appropriate procedures to allow the proper
transfer of IP packets.
+-----+
+--------------------| CE3 |
| +-----+
+-----+
........| PE3 |.........
. +-----+ .
. | .
. | .
+-----+ AC1 +-----+ Service +-----+ AC2 +-----+
| CE1 |-----| PE1 |--- Provider ---| PE2 |-----| CE2 |
+-----+ +-----+ Backbone +-----+ +-----+
. .
........................
A CE, which is connected via a given type of AC, may use an IP
Address Resolution procedure that is specific to that type of AC.
For example, an Ethernet-attached CE would use ARP, a FR-attached
CE might use Inverse ARP. If we are to allow the two CEs to have a
layer 2 connection between them, even though each AC uses a
different layer 2 technology, the PEs must intercept and "mediate"
the technology-specific address resolution procedures.
In this draft, we specify the procedures which the PEs must
implement in order to mediate the IP address resolution mechanism.
We call these procedures "ARP Mediation".
Consider a Virtual Private Wire Service (VPWS) constructed between
CE1 and CE2 in the diagram above. If AC1 and AC2 are of different
technologies, e.g. AC1 is Ethernet and AC2 is Frame Relay (FR),
then ARP requests coming from CE1 cannot be passed transparently to
CE2. PE1 must interpret the meaning of the ARP requests and
mediate the necessary information with PE2 before responding.
2.0 ARP Mediation (AM) function
The ARP Mediation (AM) function is an element of a PE node
operation that deals with the IP address resolution for CE devices
connected via a L2VPN. By placing this function in the PE node, ARP
Mediation can be made completely transparent to the CE devices.
For a given point-to-point connection between a pair of CEs, a PE
must perform three logical steps as part of the ARP Mediation
procedure:
1. Discover the IP addresses of the locally attached CE device
2. Distribute those IP Addresses to the remote PE
3. Notify the locally attached CE of the remote CE's IP address.
Shah, et. al. Expires January 2005 3
draft-shah-l2vpn-arp-mediation-04.txt
This information is gathered using the mechanisms described in the
following sections.
3.0 IP Layer 2 Interworking Circuits
The IP Layer 2 Interworking Circuits refer to Pseudowires that
carry IP datagram as the payload. At ingress, data link header of
an IP frame is removed and dispatched over the Pseudowire with or
without the optional control word. At the egress, PE encapsulates
the IP packet with the data link header used on the local
Attachment Circuit.
The use of this encapsulation is determined by the exchange of
value 0x000B as the PW type during Pseudowire establishment as
described in [PWE3-Control].
4.0 Discovery of IP Addresses of Locally Attached CE Device
An IP Layer 2 Interworking Circuit enters monitoring state right
after the configuration. During this state it performs two
functions.
. Discovery of locally attached CE IP device
. Establishment of the PW
The establishment of PW occurs independently from local CE IP
address discovery. During the period when (bi-directional) PW has
been established but local CE IP device has not been detected, only
datagrams inside of broadcast/multicast frames are propagated; IP
datagrams inside unicast frames are dropped. The IP datagrams from
unicast frames flow only when IP end systems on both Attachment
Circuits have been discovered, notified and proxy functions have
completed.
4.1 Monitoring Local Traffic
The PE devices may learn the IP addresses of the locally attached
CEs from any IP traffic, such as local multicast (e.g. 224.x.x.x)
packets, that CE may generate irrespective of reacting to specific
address resolution queries described below.
4.2 CE Devices Using ARP
If a CE device uses ARP to determine the MAC address to IP address
binding of its neighbor, the PE processes the ARP requests to learn
the IP address of local CE for the stated locally attached circuit.
If we observe the strict topology restriction whereby only one IP
router CE can exist for a given attachment circuit then PE can
Shah, et. al. Expires January 2005 4
draft-shah-l2vpn-arp-mediation-04.txt
assume that ARP request received is from the candidate IP CE and
can learn the IP to MAC address binding of the local CE.
However, if this topology restriction is relaxed, the PE can learn
the MAC address to IP address binding of the local CE but can not
assume that this CE (possibly amongst many) is the candidate IP
device that is to be interworked with the remote attachment
circuit. In these circumstances, PE may select the local CE device
using following criteria.
. Wait to learn the IP address of the remote CE (through PW
signaling) and then select the local CE that is sending the
ARP request for the remote CEÆs IP address.
. Augment cross checking with the local IP address learned
through listening of link local multicast packets (as per
section 4.1 above)
. Augment cross checking with the local IP address learned
through Router Discovery protocol (as described below in
section 4.5).
. There is still a possibility that PE may not receive IP
address advertisement from the remote and there may exist
multiple local IP routers that attempt to 'connect' to
remote CEs. In this situation, PE may use some arbitrary
criteria to select one IP device from many (such as first ARP
received), or have operator configure the IP address of
local CE. Note that operator does not have to configure the
MAC address of the local CE as that would be learned through
ARP mechanisms described above nor the IP address of the
remote CE as that would be learned through Pseudowire
signaling described later in this document.
Once the local CE has been discovered for the given attachment
circuit, PE responds to the subsequent ARP requests from that
device with the MAC address of his own. The PE signals the IP
address to the remote PE and may initiate the unsolicited ARP
response as a means to notify local CE, the IP address to MAC
address binding of the remote, in order to facilitate unicast
traffic between two CEs.
The PE may periodically generate ARP request messages to the CE's
IP address as a means to verify the continued existence of the
address and its binding to the stated MAC address. The absence of a
response from the CE device for a given number of retries could be
used as a cause for a withdrawal of the IP address advertisement to
the remote PE and entering into the address resolution phase to
rediscover the attached CE's IP address. Note that such "heartbeat"
scheme is needed only for broadcast links, as a loss of CE may
otherwise be undetectable.
Shah, et. al. Expires January 2005 5
draft-shah-l2vpn-arp-mediation-04.txt
4.3 CE Devices Using Inverse ARP
If a CE device uses Inverse ARP to determine the IP address of its
neighbor, the attached PE processes the Inverse ARP request for
stated circuit and responds with an Inverse ARP reply containing
the remote CE's IP address, if the address is known. If the PE does
not yet have the remote CE's IP address, it does not respond, but
notes the IP address of the local CE and the circuit information.
Subsequently, when the IP address of the remote CE becomes
available, the PE may initiate the Inverse ARP request as a means
to notify the local CE about the IP address of the remote CE.
This is a typical operation for Frame Relay and ATM attachment
circuits. In the cases where the CE does not use Inverse ARP, PE
could still discover the CE as described in section 4.1 and 4.5.
4.4 CE Devices Using PPP
When PPP link becomes operational after the LCP negotiations, PE
performs following action
. If PE does not know the IP address of the local CE, it
generates configure-request without configure IP address TLV.
The response from CE is accepted as IP address of the local
CE.
. If PE knows the IP address of the remote CE, it sends IPCP
configure-request with IP address of the remote CE in the
configure IP address TLV
. If PE receives IPCP configure-request without configure IP
address TLV, and if it knows the IP address of the remote CE,
it responds with configure NAK with configure IP address TLV
set with remote CEÆs IP address. However, if PE does not know
the remote CEÆs IP address yet, it responds with configure
NAK.
. If PE does not know the IP address of the remote CE, it sends
IPCP configure-request with IP address as zero. The response
from CE is recorded and used to validate the incoming remote
CEÆs IP address via PW signaling.
The PE must deny configurations such as header compression and
encryptions in the NCP packets with such options.
4.5 Proactive method
In order to learn the IP address of the CE device for a given
Attachment Circuit, the PE device may execute Router Discovery
Protocol [RFC 1256] whereby a Router Discovery Request (ICMP û
router solicitation) message is sent using a source IP address of
zero. The IP address of the CE device is extracted from the Router
Discovery Response (ICMP û router advertisement) message from the
CE.
Shah, et. al. Expires January 2005 6
draft-shah-l2vpn-arp-mediation-04.txt
The use of the router discovery mechanism by the PE is optional.
5.0 IP Address Distribution Between PE
5.1 When To Distribute IP Address
A PE device advertises the IP address of the attached CE only when
the encapsulation type of the Pseudowire is IP L2 interworking
(0x0B). It is quite possible that the IP address of a CE device is
not available at the time the PW labels are advertised. For
example, in Frame Relay the CE device dispatches inverse ARP
request only when the DLCI is active; if the PE signals the DLCI to
be active only when it has received the IP address along with the
PW-FEC from the remote PE, a chicken and egg situation arises. In
order to avoid such problems, the PE must be prepared to advertise
the PW-FEC before the CE's IP address is known. When the IP address
of the CE device does become available, the PE re-advertises the
PW-FEC along with the IP.
Similarly, if the PE detects invalidation of the CE's IP address
(by methods described above) the PE must re-advertise the PW-FEC
with null IP address to denote the withdrawal of the CE's IP
address. The receiving PE then waits for the notification of remote
IP address. During this period, propagation of unicast IP traffic
is suspended while continuing to let multicast IP traffic flow.
If two CE devices are locally attached to the PE where, one CE is
connected to an Ethernet data link and the other to a Frame Relay
interface, for example, the IP addresses are learned in the same
manner described above. However, since the CE devices are local,
the distribution of IP addresses for these CE devices is a local
step.
5.2 LDP Based Distribution
The [PWE3-CONTROL] uses Label Distribution Protocol (LDP) transport
to exchange PW-FEC in the Label Mapping message in a downstream
unsolicited mode. The PW-FEC comes in two flavors; Pwid and
Generalized ID FEC elements and shares some fields that are common
between them. The discussions below refer to these common fields
for IP L2 Interworking Circuits.
The IP L2 Interworking uses IP datagram as payload over the
Pseduowire. The use of such encapsulation is identified by PW type
field of the PW-FEC as the value 0x000B [PWE3-Control].
In addition, this document defines an IP address TLV that must be
included in the optional TLV field of the Label Mapping message
Shah, et. al. Expires January 2005 7
draft-shah-l2vpn-arp-mediation-04.txt
when advertising PW-FEC for the IP L2 Interworking Circuit. Such
use of optional TLV in the Label Mapping message to extend the
attributes of the PW-FEC has also been specified in the [PWE3-
Control].
When processing a received PW-FEC, the PE matches the PW-Id and PW-
type with the locally configured PW-Id to determine if the PW-FEC
is of type IP L2 Interworking. If matched, it further checks the
presence of IP address TLV. If an IP address TLV is absent, a Label
Release message is issued to reject the PW establishment.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1|0| IP address TLV (TBD) | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IP Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The Length field is defined as the length of the IP address and is
set to value 4.
The IP address field is set to value null to denote that
advertising PE has not learned the IP address of his local CE
device. The non-zero value of the IP address field denotes IP
address of advertising PEÆs attached CE device.
The IP address TLV is also used in the LDP notification message
along with the PW-FEC. The IP address TLV in Notification message
is used as an update mechanism to notify the changes in the IP
address of the local CE device as described in [SHAH-CONTROL].
5.3 Out-of-band Distribution, Manual Configuration
In some cases, it may not be possible to deduce the IP addresses
from the VPN traffic nor induce remote PEs to supply the necessary
information on demand. For those cases, out-of-band methods, such
as manual configuration, could be used. The use of these types of
methods is useful only to handle corner cases.
5.4 Single sided ARP mediation
In this configuration, one PE device treats the Pseudowire as a
homogeneous circuit, while the other PE device treats it as a
heterogenous circuit. For example, if PE1 is connected to an
Ethernet Attachment Circuit and PE2 is connected to an ATM
Attachment Circuit, PE1 and PE2 would both treat the Pseudowire as
Shah, et. al. Expires January 2005 8
draft-shah-l2vpn-arp-mediation-04.txt
of type Ethernet. From PE1's point of view, the circuit is
homogeneous, since the Attachment Circuit and the Pseudowire are
both Ethernet. Hence PE1 does no ARP mediation. From PE2's point of
view, the circuit is heterogeneous, so PE2 performs ARP mediation.
That is,
o PE2 signals to PE1 that the PW Type is Ethernet,
o PE2 learns the IP address of remote CE from Ethernet
frames received over the PW,
o PE2 learns the IP address of locally attached ATM CE,
o PE2 proxies the IP address of each CE to the other,
o PE2 decapsulates the ATM data link header and
reencapsulates with an Ethernet header before forwarding
the IP data frames from its local CE over the PW. The
information used to build the Ethernet data link header
is obtained through ARP mediation functions. Similar
header manipulation is performed when Ethernet IP frames
are forwarded to ATM Attachment Circuit,
o Drop all non IP Ethernet frames received over Ethernet
PW.
The above example show how single sided ARP mediation would work
when Pseudowire is Ethernet. However, the choice of Pseudowire type
and which side performs the ARP mediation functions is largely
dictated by the existing network topology and how this service is
rolled out. The single sided architecture is not restricted to a
specific Pseudowire type.
In summary, single sided configuration handles ARP mediation as PE
would typically when managing two locally attached heterogenous
Attachment Circuits.
6.0 How CE Learns The Remote CE's IP address
Once the PE has received the remote CE's IP address information
from the remote PE, it will either initiate an address resolution
request or respond to an outstanding request from the attached CE
device.
6.1 CE Devices Using ARP
When the PE learns the remote CE's IP address as described in
section 5.1 and 5.2, it may or may not know the local CE's IP
address. If the local CE's IP address is not known, the PE must
wait until it is acquired through one of the methods described in
sections 4.1, 4.3 and 4.5. If the IP address of the local CE is
known, the PE may choose to generate an unsolicited ARP message to
notify the local CE about the binding of the remote CE's IP address
with the PE's own MAC address.
Shah, et. al. Expires January 2005 9
draft-shah-l2vpn-arp-mediation-04.txt
When the local CE generates an ARP request, the PE must proxy the
ARP response using its own MAC address as the source hardware
address and remote CE's IP address as the source protocol address.
The PE must respond only to those ARP requests whose destination
protocol address matches the remote CE's IP address.
6.2 CE Devices Using Inverse ARP
When the PE learns the remote CE's IP address, it should generate
an Inverse ARP request. In case, the local circuit requires
activation e.g. Frame Relay, PE should activate it first before
sending Inverse ARP request. It should be noted, that PE might
never receive the response to its own request, nor see any CE's
Inverse ARP request in cases where CE is pre-configured with remote
CE IP address or the use of Inverse ARP is not enabled. In either
case CE has used other means to learn the IP address of his
neighbor.
6.3 CE Devices Using PPP
When the PE learns the remote CE's IP address, it should initiate
the Configure-Request using the remote CE's IP address or respond
to pending Configure-Request from the local CE. As noted earlier,
all other configuration options related to compression,
encryptions, etc., should be rejected.
7.0 Use of IGPs with IP L2 Interworking L2VPNs
In an IP L2 interworking L2VPN, when an IGP on a CE connected to a
broadcast link is cross-connected with an IGP on a CE connected to
a point-to-point link, there are routing protocol related issues
that must be addressed. The link state routing protocols are
cognizant of the underlying link characteristics and behave
accordingly when establishing neighbor adjacencies, representing
the network topology, and passing protocol packets.
7.1 OSPF
The OSPF protocol treats broadcast link type with a special
procedure that engages in neighbor discovery to elect a designated
and a backup designated router (DR and BDR respectively) with which
it forms adjacencies. However, these procedures are neither
applicable nor understood by OSPF running on a point-to-point link.
By cross-connecting two neighbors with disparate link types, an IP
L2 interworking L2VPN has the potential to experience connectivity
issues.
Shah, et. al. Expires January 2005 10
draft-shah-l2vpn-arp-mediation-04.txt
Additionally, the link type specified in the router LSA will not
match for two routers that are supposedly sharing the same link
type. Finally, each OSPF router generates network LSAs when
connected to a broadcast link such as Ethernet, receipt of which by
an OSPF router on the point-to-point link further adds to the
confusion.
Fortunately, the OSPF protocol provides a configuration option
(ospfIfType), whereby OSPF will treat the underlying physical
broadcast link as a point-to-point link.
It is strongly recommended that all OSPF protocols on CE devices
connected to Ethernet interfaces use this configuration option when
attached to a PE that is participating in an IP L2 Interworking
VPN.
7.2 IS-IS
The IS-IS protocol sends a LAN Hello PDU (IIH packet) with the MAC
address and the IP address of the intermediate system (i.e., CE
device) when attached to Ethernet links. The CE device expects its
neighbor to insert its own MAC and IP address in the response. If
the neighbor is connected via a point-to-point link type, the LAN
Hello PDU will be silently discarded. Similarly, Hello PDUs on the
point-to-point link do not contain any MAC address, which will
confuse a neighbor on an Ethernet link, if these two neighbors were
cross-connected via above described mechanisms.
Thus, use of the IS-IS protocol on CE devices presents problems
when interconnected by disparate data link types in an IP L2
Interworking VPN environment. There are some mechanisms defined in
draft-ietf-isis-igp-p2p-over-lan-00.txt to accommodate point-to-
point behavior over broadcast networks. The feasibility of such
techniques to solve this problem is under review.
It is important to note that the use of the IS-IS protocol in
enterprise networks (i.e., CE routers) is less common. The IS-IS
related difficulties for IP L2 Interworking VPNs, hence are
minimized.
7.3 RIP
RIP protocol broadcasts RIP advertisements every 30 seconds. If the
group/broadcast address snooping mechanism is used as described
above, the attached PE can learn the advertising (CE) router's IP
address from the IP header of the advertisement. No special
configuration is required for RIP in this type of Layer 2 IP
Interworking L2VPN.
Shah, et. al. Expires January 2005 11
draft-shah-l2vpn-arp-mediation-04.txt
8.0 Security Considerations
The security aspects of this solution will be discussed at a later
time.
9.0 Acknowledgements
The authors would like to thank Yetik Serbest, Prabhu Kavi, Bruce
Lasley and other folks who participated in the discussions related
to this draft.
10.0 References
10.1 Normative References
[ARP] RFC 826, STD 37, D. Plummer, "An Ethernet Address Resolution
Protocol: Or Converting Network Protocol Addresses to 48.bit
Ethernet Addresses for Transmission on Ethernet Hardware".
[INVARP] RFC 2390, T. Bradley et al., "Inverse Address Resolution
Protocol".
10.2 Informative References
[L2VPN-REQ] W. Augustyn et al., "Service Requirements for Layer 2
Provider Provisioned Virtual Private Networks", February 2003, work
in progress.
[L2VPN-FRM] L. Andersson et al., "L2VPN Framework", January 2003,
work in progress.
[PPP-IPCP] RFC 1332, G. McGregor, "The PPP Internet Protocol
Control Protocol (IPCP)".
[L2VPN-Kompella] K. Kompella et al., "Layer 2 VPNs Over Tunnels",
June 2002, work in progress.
[PWE3-CONTROL] L. Martini et al., "Transport of Layer 2 Frames Over
MPLS", November 2002, work in progress.
[L2VPN-Signaling] E. Rosen et al., "LDP-based Signaling for
L2VPNs", September 2002, work in progress.
[PROXY-ARP] RFC 925, J. Postel, "Multi-LAN Address Resolution".
[SHAH-CONTROL] H. Shah et al., ôDynamic Parameters Signaling for
MPLS-based Pseudowiresö, June 2003, work in progress
Shah, et. al. Expires January 2005 12
draft-shah-l2vpn-arp-mediation-04.txt
11.0 Authors' Addresses
Himanshu Shah
35 Nagog Park,
Acton, MA 01720
Email: hshah@ciena.com
Eric Rosen
Cisco Systems
1414 Massachusetts Avenue,
Boxborough, MA 01719
Email: erosen@cisco.com
Waldemar Augustyn
Email: waldemar@nxp.com
Giles Heron
PacketExchange Ltd.
The Truman Brewery
91 Brick Lane
LONDON E1 6QL
United Kingdom
Email: giles@packetexchange.net
Sunil Khandekar and Vach Kompella
Alcatel
274 Ferguson Dr.
Mountain View, CA 94043
Email: sunil@timetra.com
Email: vkompella@timetra.com
Toby Smith
Laurel Networks
Omega Corporate Center
1300 Omega drive
Pittsburgh, PA 15205
Email: jsmith@laurelnetworks.com
Arun Vishwanathan
Force10 Networks
1440 McCarthy Blvd.,
Milpitas, CA 95035
Email: arun@force10networks.com
Ashwin Moranganti
Axiowave Network
Marlboro, MA 01720
Andrew G. Malis
Tellabs
2730 Orchard Parkway
San Jose, CA 95134
Email: Andy.Malis@vivacenetworks.com
Shah, et. al. Expires January 2005 13
draft-shah-l2vpn-arp-mediation-04.txt
Steven Wright
Bell South Corp
Email: steven.wright@bellsouth.com
Vasile Radoaca
Nortel Networks
Email: vasile@nortelnetworks.com
IPR Notice
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the
IETFÆs procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11. Copies of
claims of rights made available for publication and any assurances
of licenses to be made available, or the result of an attempt made
to obtain a general license or permission of such proprietary
rights by implementers or users of this specification can be
obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights which may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive
Director.
Full Copyright Statement
"Copyright (C) The Internet Society (2001). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain
it or assist in its implementation may be prepared, copied,
published and distributed, in whole or in part, without restriction
of any kind, provided that the above copyright notice and this
paragraph are included on all such copies and derivative works.
However, this document itself may not be modified in any way, such
as by removing the copyright notice or references to the Internet
Society or other Internet organizations, except as needed for the
purpose of developing Internet standards in which case the
procedures for copyrights defined in the Internet Standards process
must be followed, or as required to translate it into languages
other than English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on
an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET
Shah, et. al. Expires January 2005 14
draft-shah-l2vpn-arp-mediation-04.txt
ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE."
Shah, et. al. Expires January 2005 15
| PAFTECH AB 2003-2026 | 2026-04-19 09:31:49 |