One document matched: draft-schoenw-netmod-yang-types-01.txt
Differences from draft-schoenw-netmod-yang-types-00.txt
Network Working Group J. Schoenwaelder, Ed.
Internet-Draft Jacobs University
Intended status: Standards Track July 14, 2008
Expires: January 15, 2009
Common YANG Data Types
draft-schoenw-netmod-yang-types-01
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on January 15, 2009.
Copyright Notice
Copyright (C) The IETF Trust (2008).
Schoenwaelder Expires January 15, 2009 [Page 1]
Internet-Draft YANG-TYPES July 2008
Abstract
This document introduces a collection of common data types to be used
with the YANG data modeling language.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Key Words . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Core YANG Derived Types . . . . . . . . . . . . . . . . . . . 5
4. Internet Specific Derived Types . . . . . . . . . . . . . . . 11
5. IEEE 802 Specific Derived Types . . . . . . . . . . . . . . . 18
6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 20
7. Security Considerations . . . . . . . . . . . . . . . . . . . 21
8. Contributors . . . . . . . . . . . . . . . . . . . . . . . . . 22
9. Open Issues . . . . . . . . . . . . . . . . . . . . . . . . . 23
10. References . . . . . . . . . . . . . . . . . . . . . . . . . . 24
10.1. Normative References . . . . . . . . . . . . . . . . . . 24
10.2. Informative References . . . . . . . . . . . . . . . . . 24
Author's Address . . . . . . . . . . . . . . . . . . . . . . . . . 25
Intellectual Property and Copyright Statements . . . . . . . . . . 26
Schoenwaelder Expires January 15, 2009 [Page 2]
Internet-Draft YANG-TYPES July 2008
1. Introduction
YANG [YANG] is a data modeling language used to model configuration
and state data manipulated by the NETCONF [RFC4741] protocol. The
YANG language supports a small set of built-in data types and
provides mechanisms to derive other types from the built-in types.
This document introduces a collection of common data types derived
from the built-in YANG data types. The definitions are organized in
several YANG modules. The "yang-types" module contains generally
useful data types. The "inet-types" module contains definitions that
are relevant for the Internet protocol suite while the "ieee-types"
module contains definitions that are relevant for IEEE 802 protocols.
Their derived types are generally designed to be applicable for
modeling all areas of management information.
Schoenwaelder Expires January 15, 2009 [Page 3]
Internet-Draft YANG-TYPES July 2008
2. Key Words
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in BCP
14, [RFC2119].
Schoenwaelder Expires January 15, 2009 [Page 4]
Internet-Draft YANG-TYPES July 2008
3. Core YANG Derived Types
module yang-types {
// XXX namespace to be allocated by IANA
namespace "urn:ietf:params:xml:ns:yang:yang-types";
prefix "yang";
organization
"YANG Language Design Team";
contact
"Juergen Schoenwaelder (Editor)
<j.schoenwaelder@jacobs-university.de>";
description
"This module contains standard derived YANG types.";
revision 2009-05-22 {
description "Initial revision.";
}
/*
* collection of counter and gauge types
*/
typedef counter32 {
type uint32;
description
"The counter32 type represents a non-negative integer
which monotonically increases until it reaches a
maximum value of 2^32-1 (4294967295 decimal), when it
wraps around and starts increasing again from zero.
Counters have no defined `initial' value, and thus, a
single value of a counter has (in general) no information
content. Discontinuities in the monotonically increasing
value normally occur at re-initialization of the
management system, and at other times as specified in the
description of an object instance using this type. If
such other times can occur, for example, the creation of
an object instance of type counter32 at times other than
re-initialization, then a corresponding object should be
defined, with an appropriate type, to indicate the last
discontinuity.
The counter32 type should not be used for configuration
Schoenwaelder Expires January 15, 2009 [Page 5]
Internet-Draft YANG-TYPES July 2008
objects. A default statement should not be used for
attributes with a type value of counter32.";
reference
"RFC 2578 (STD 58)";
}
typedef zero-based-counter32 {
type yang:counter32;
default "0";
description
"The zero-based-counter32 type represents a counter32
which has the defined `initial' value zero.";
reference
"RFC 2021";
}
typedef counter64 {
type uint64;
description
"The counter64 type represents a non-negative integer
which monotonically increases until it reaches a
maximum value of 2^64-1 (18446744073709551615), when
it wraps around and starts increasing again from zero.
Counters have no defined `initial' value, and thus, a
single value of a counter has (in general) no information
content. Discontinuities in the monotonically increasing
value normally occur at re-initialization of the
management system, and at other times as specified in the
description of an object instance using this type. If
such other times can occur, for example, the creation of
an object instance of type counter64 at times other than
re-initialization, then a corresponding object should be
defined, with an appropriate type, to indicate the last
discontinuity.
The counter64 type should not be used for configuration
objects. A default statement should not be used for
attributes with a type value of counter64.";
reference
"RFC 2578 (STD 58)";
}
typedef zero-based-counter64 {
type yang:counter64;
default "0";
description
"The zero-based-counter64 type represents a counter64
Schoenwaelder Expires January 15, 2009 [Page 6]
Internet-Draft YANG-TYPES July 2008
which has the defined `initial' value zero.";
reference
"RFC 2856";
}
typedef gauge32 {
type uint32;
description
"The gauge32 type represents a non-negative integer,
which may increase or decrease, but shall never
exceed a maximum value, nor fall below a minimum
value. The maximum value can not be greater than
2^32-1 (4294967295 decimal), and the minimum value
can not be smaller than 0. The value of a gauge32
has its maximum value whenever the information
being modeled is greater than or equal to its
maximum value, and has its minimum value whenever
the information being modeled is smaller than or
equal to its minimum value. If the information
being modeled subsequently decreases below
(increases above) the maximum (minimum) value, the
gauge32 also decreases (increases).";
reference
"RFC 2578 (STD 58)";
}
typedef gauge64 {
type uint64;
description
"The gauge64 type represents a non-negative integer,
which may increase or decrease, but shall never
exceed a maximum value, nor fall below a minimum
value. The maximum value can not be greater than
2^64-1 (18446744073709551615), and the minimum value
can not be smaller than 0. The value of a gauge64
has its maximum value whenever the information
being modeled is greater than or equal to its
maximum value, and has its minimum value whenever
the information being modeled is smaller than or
equal to its minimum value. If the information
being modeled subsequently decreases below
(increases above) the maximum (minimum) value, the
gauge64 also decreases (increases).";
reference
"RFC 2856";
}
/*
Schoenwaelder Expires January 15, 2009 [Page 7]
Internet-Draft YANG-TYPES July 2008
* collection of identifier related types
*/
typedef uri {
type string;
description
"A uri type represents Uniform Resource Identifier (URI)
as defined by STD 66.
Objects using this type MUST be in US-ASCII encoding, and
MUST be normalized as described by RFC 3986 Sections
6.2.1, 6.2.2.1, and 6.2.2.2. All unnecessary
percent-encoding is removed, and all case-insensitive
characters are set to lowercase except for hexadecimal
digits, which are normalized to uppercase as described in
Section 6.2.2.1.
The purpose of this normalization is to help provide unique
URIs. Note that this normalization is not sufficient to
provide uniqueness. Two URIs that are textually distinct
after this normalization may still be equivalent.
Objects using this type MAY restrict the schemes that they
permit. For example, 'data:' and 'urn:' schemes might not
be appropriate.
A zero-length URI is not a valid URI. This can be used to
express 'URI absent' where required, for example when used
as an index field.";
reference
"RFC 3986 (STD 66), RFC 3305, and RFC 5017";
}
typedef object-identifier {
type string {
pattern '([0-1](\.[1-3]?[0-9]))|(2.(0|([1-9]\d*)))'
+ '(\.(0|([1-9]\d*)))*';
}
description
"The object-identifier type represents administratively
assigned names in a registration-hierarchical-name tree.
Values of this type are denoted as a sequence of numerical
non-negative sub-identifier values. Each sub-identifier
value MUST NOT exceed 2^32-1 (4294967295). Sub-identifiers
are separated by single dots and without any intermediate
white space.
Schoenwaelder Expires January 15, 2009 [Page 8]
Internet-Draft YANG-TYPES July 2008
Although the number of sub-identifiers is not limited,
module designers should realize that there may be
implementations that stick with the SMIv1/v2 limit of 128
sub-identifiers.";
reference
"ITU-T Recommendation X.660 / ISO/IEC 9834-1";
}
/*
* collection of date and time related types
*/
typedef date-and-time {
type string {
pattern '\d{4}-\d{2}-\d{2}T\d{2}:\d{2}:\d{2}(\.d*)?'
+ '(Z|(\+|-)\d{2}:\d{2})';
}
description
'The date-and-time type is a profile of the ISO 8601
standard for representation of dates and times using the
Gregorian calendar. The format is most easily described
using the following ABFN (see RFC 3339):
date-fullyear = 4DIGIT
date-month = 2DIGIT ; 01-12
date-mday = 2DIGIT ; 01-28, 01-29, 01-30, 01-31
time-hour = 2DIGIT ; 00-23
time-minute = 2DIGIT ; 00-59
time-second = 2DIGIT ; 00-58, 00-59, 00-60
time-secfrac = "." 1*DIGIT
time-numoffset = ("+" / "-") time-hour ":" time-minute
time-offset = "Z" / time-numoffset
partial-time = time-hour ":" time-minute ":" time-second
[time-secfrac]
full-date = date-fullyear "-" date-month "-" date-mday
full-time = partial-time time-offset
date-time = full-date "T" full-time';
reference "RFC 3339";
}
typedef timeticks {
type uint32;
description
"The timeticks type represents a non-negative integer
which represents the time, modulo 2^32 (4294967296
decimal), in hundredths of a second between two epochs.
Schoenwaelder Expires January 15, 2009 [Page 9]
Internet-Draft YANG-TYPES July 2008
When objects are defined which use this type, the
description of the object identifies both of the reference
epochs.";
reference
"RFC 2578 (STD 58)";
}
typedef timestamp {
type yang:timeticks;
description
"The timestamp type represents the value of an associated
timeticks object at which a specific occurrence
happened. The specific occurrence must be defined in the
description of any object defined using this type. When
the specific occurrence occurred prior to the last time
the associated timeticks attribute was zero, then the
timestamp value is zero. Note that this requires all
timestamp values to be reset to zero when the value of
the associated timeticks attribute reaches 497+ days and
wraps around to zero.
The associated timeticks object must be specified
in the description of any object using this type.";
reference
"RFC 2579 (STD 58)";
}
/*
* collection of generic address types
*/
typedef phys-address {
type string;
description
"Represents media- or physical-level addresses.";
reference
"RFC 2579 (STD 58)";
}
}
Schoenwaelder Expires January 15, 2009 [Page 10]
Internet-Draft YANG-TYPES July 2008
4. Internet Specific Derived Types
module inet-types {
// XXX namespace to be allocated by IANA
namespace "urn:ietf:params:xml:ns:yang:inet-types";
prefix "inet";
organization
"YANG Language Design Team";
contact
"Juergen Schoenwaelder (Editor)
<j.schoenwaelder@jacobs-university.de>";
description
"This module contains standard derived YANG types
for Internet addresses and related things.";
revision 2008-06-07 {
description "Initial revision.";
}
/*
* collection of protocol field related types
*/
typedef ip-version {
type enumeration {
enum unknown {
value 0;
description
"An unknown or unspecified version of the
Internet protocol.";
}
enum ipv4 {
value 1;
description
"The IPv4 protocol as defined in RFC 791.";
}
enum ipv6 {
value 2;
description
"The IPv6 protocol as defined in RFC 2460.";
}
}
description
Schoenwaelder Expires January 15, 2009 [Page 11]
Internet-Draft YANG-TYPES July 2008
"This value represents the version of the IP protocol.";
reference
"RFC 791 (STD 5), RFC 2460";
}
typedef dscp {
type uint8 {
range "0..63";
}
description
"The dscp type represents a Differentiated Services
Code-Point that may be used for marking a traffic
stream.";
reference
"RFC 3289, RFC 2474, RFC 2780";
}
typedef flow-label {
type uint32 {
range "0..1048575";
}
description
"The flow-label type represents flow identifier or
Flow Label in an IPv6 packet header that may be
used to discriminate traffic flows.";
reference
"RFC 2460";
}
typedef port-number {
type uint16 {
range "1..65535";
}
description
"The port-number type represents a 16-bit port
number of an Internet transport layer protocol
such as UDP, TCP, DCCP or SCTP. Port numbers are
assigned by IANA. A current list of all
assignments is available from
<http://www.iana.org/>.
Note that the value zero is not a valid port
number. A union type might be used in situations
where the value zero is meaningful.";
reference
"RFC 4001";
}
Schoenwaelder Expires January 15, 2009 [Page 12]
Internet-Draft YANG-TYPES July 2008
/*
* collection of autonomous system related types
*/
typedef as-number {
type uint32;
description
"The as-number type represents autonomous system numbers
which identify an Autonomous System (AS). An AS is a set
of routers under a single technical administration, using
an interior gateway protocol and common metrics to route
packets within the AS, and using an exterior gateway
protocol to route packets to other ASs'. IANA maintains
the AS number space and has delegated large parts to the
regional registries.
Autonomous system numbers are currently limited to 16 bits
(0..65535). There is however work in progress to enlarge
the autonomous system number space to 32 bits. This
textual convention therefore uses an uint32 base type
without a range restriction in order to support a larger
autonomous system number space.";
reference
"RFC 1771, RFC 1930, RFC 4001";
}
/*
* collection of IP address and hostname related types
*/
typedef ip-address {
type union {
type inet:ipv4-address;
type inet:ipv6-address;
}
description
"The ip-address type represents an IP address and
is IP version neutral. The format of the textual
representations implies the IP version.";
}
typedef ipv4-address {
type string {
pattern
'(([0-1]?[0-9]?[0-9]|2[0-4][0-9]|25[0-5])\.){3}'
+ '([0-1]?[0-9]?[0-9]|2[0-4][0-9]|25[0-5])'
+ '(%[\p{N}\p{L}]+)?';
}
Schoenwaelder Expires January 15, 2009 [Page 13]
Internet-Draft YANG-TYPES July 2008
description
"The ipv4-address type represents an IPv4 address in
dotted-quad notation. The IPv4 address may include
a zone index, separated by a % sign.
The zone index is used to disambiguate identical address
values. For link-local addresses, the zone index will
typically be the interface index number or the name of an
interface. If the zone index is not present, the default
zone of the device will be used.";
}
typedef ipv6-address {
type string {
pattern
/* full */
'((([0-9a-fA-F]{1,4}:){7})([0-9a-fA-F]{1,4})'
+ '(%[\p{N}\p{L}]+)?)'
/* mixed */
+ '|((([0-9a-fA-F]{1,4}:){6})(([0-9]{1,3}\.'
+ '[0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}))'
+ '(%[\p{N}\p{L}]+)?)'
/* shortened */
+ '|((([0-9a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*(::)'
+ '(([0-9a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*'
+ '(%[\p{N}\p{L}]+)?)'
/* shortened mixed */
+ '((([0-9a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*(::)'
+ '(([0-9a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*'
+ '(([0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}))'
+ '(%[\p{N}\p{L}]+)?)';
}
description
"The ipv6-address type represents an IPv6 address in
full, mixed, shortened and shortened mixed notation.
The IPv6 address may include a zone index, separated
by a % sign.
The zone index is used to disambiguate identical address
values. For link-local addresses, the zone index will
typically be the interface index number or the name of an
interface. If the zone index is not present, the default
zone of the device will be used.";
reference
"RFC 4007: IPv6 Scoped Address Architecture";
}
typedef ip-prefix {
Schoenwaelder Expires January 15, 2009 [Page 14]
Internet-Draft YANG-TYPES July 2008
type union {
type inet:ipv4-prefix;
type inet:ipv6-prefix;
}
description
"The ip-prefix type represents an IP prefix and
is IP version neutral. The format of the textual
representations implies the IP version.";
}
typedef ipv4-prefix {
type string {
pattern
'(([0-1]?[0-9]?[0-9]|2[0-4][0-9]|25[0-5])\.){3}'
+ '([0-1]?[0-9]?[0-9]|2[0-4][0-9]|25[0-5])'
+ '/\p{N}+';
}
description
"The ipv4-prefix type represents an IPv4 address prefix.
The prefix length is given by the number following the
slash character and must be less than or equal 32.
A prefix length value of n corresponds to an IP address
mask which has n contiguous 1-bits from the most
significant bit (MSB) and all other bits set to 0.
The IPv4 address represented in dotted quad notation
should have all bits that do not belong to the prefix
set to zero.";
}
typedef ipv6-prefix {
type string {
pattern
/* full */
'((([0-9a-fA-F]{1,4}:){7})([0-9a-fA-F]{1,4})'
+ '/\p{N}+)'
/* mixed */
+ '|((([0-9a-fA-F]{1,4}:){6})(([0-9]{1,3}\.'
+ '[0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}))'
+ '/\p{N}+)'
/* shortened */
+ '|((([0-9a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*(::)'
+ '(([0-9a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*'
+ '/\p{N}+)'
/* shortened mixed */
+ '((([0-9a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*(::)'
+ '(([0-9a-fA-F]{1,4}:)*([0-9a-fA-F]{1,4}))*'
Schoenwaelder Expires January 15, 2009 [Page 15]
Internet-Draft YANG-TYPES July 2008
+ '(([0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}))'
+ '/\p{N}+)';
}
description
"The ipv6-prefix type represents an IPv6 address prefix.
The prefix length is given by the number following the
slash character and must be less than or equal 128.
A prefix length value of n corresponds to an IP address
mask which has n contiguous 1-bits from the most
significant bit (MSB) and all other bits set to 0.
The IPv6 address should have all bits that do not belong
to the prefix set to zero.";
}
/*
* Domain name and URI types.
*/
typedef domain-name {
type string {
pattern '([a-zA-Z0-9\-]+\.)*[a-zA-Z0-9\-]+';
}
description
"The domain-name type represents a DNS domain
name. The name SHOULD be fully qualified
whenever possible.
The description clause of objects using the
domain-name type MUST describe how (and when)
these names are resolved to IP addresses.
Note that the resolution of a domain-name value
may require to query multiple DNS records (e.g.,
A for IPv4 and AAAA for IPv6). The order of the
resolution process and which DNS record takes
precedence depends on the configuration of the
resolver.";
reference
"RFC 1034";
}
typedef host {
type union {
type inet:ip-address;
type inet:domain-name;
}
Schoenwaelder Expires January 15, 2009 [Page 16]
Internet-Draft YANG-TYPES July 2008
description
"The host type represents either an IP address
or a DNS domain name.";
}
typedef uri {
type string; // TBD: add the regex from RFC 3986 here?
description
"The uri type represents a Uniform Resource Identifier
(URI) as defined by STD 66.
Objects using the uri type must be in US-ASCII encoding,
and MUST be normalized as described by RFC 3986 Sections
6.2.1, 6.2.2.1, and 6.2.2.2. All unnecessary
percent-encoding is removed, and all case-insensitive
characters are set to lowercase except for hexadecimal
digits, which are normalized to uppercase as described in
Section 6.2.2.1.
The purpose of this normalization is to help provide
unique URIs. Note that this normalization is not
sufficient to provide uniqueness. Two URIs that are
textually distinct after this normalization may still be
equivalent.
Objects using the uri type may restrict the schemes that
they permit. For example, 'data:' and 'urn:' schemes
might not be appropriate.
A zero-length URI is not a valid URI. This can be used to
express 'URI absent' where required."
reference "RFC 3986 STD 66 and RFC 3305"
}
}
Schoenwaelder Expires January 15, 2009 [Page 17]
Internet-Draft YANG-TYPES July 2008
5. IEEE 802 Specific Derived Types
module ieee-types {
// XXX namespace to be allocated by IANA
namespace "urn:ietf:params:xml:ns:yang:ieee-types";
prefix "ieee";
import yang-types {
prefix yang;
}
organization
"YANG Language Design Team";
contact
"Juergen Schoenwaelder (Editor)
<j.schoenwaelder@jacobs-university.de>";
description
"This module contains standard derived YANG types
for IEEE 802 addresses and related things.";
revision 2008-05-22 {
description "Initial revision.";
}
/*
* collection of IEEE address type definitions
*/
typedef mac-address {
type yang:phys-address {
pattern '([0-9a-fA-F]{2}:){5}[0-9a-fA-F]{2}';
}
description
"The mac-address type represents an 802 MAC address
represented in the `canonical' order defined by
IEEE 802.1a, i.e., as if it were transmitted least
significant bit first, even though 802.5 (in contrast
to other 802.x protocols) requires MAC addresses to
be transmitted most significant bit first.";
reference
"RFC 2579 STD 58";
}
/*
Schoenwaelder Expires January 15, 2009 [Page 18]
Internet-Draft YANG-TYPES July 2008
* collection of IEEE 802 related identifier types
*/
typedef bridgeid {
type string {
pattern '[0-9a-fA-F]{4}:'
+ '([0-9a-fA-F]{2}:){5}[0-9a-fA-F]{2}';
}
description
"The bridgeid type represents identifers that uniquely
identify a bridge. Its first four hexadecimal digits
contain a priority value followed by a colon. The
remaining characters contain the MAC address used to
refer to a bridge in a unique fashion (typically, the
numerically smallest MAC address of all ports on the
bridge).";
reference
"RFC 4188";
}
typedef vlanid {
type uint16 {
range "1..4094";
}
description
"The vlanid type uniquely identifies a VLAN. This is
the 12-bit VLAN-ID used in the VLAN Tag header. The
range is defined by the referenced specification.";
reference
"IEEE Std 802.1Q 2003 Edition, Virtual Bridged Local
Area Networks.";
}
}
Schoenwaelder Expires January 15, 2009 [Page 19]
Internet-Draft YANG-TYPES July 2008
6. IANA Considerations
A registry for standard YANG modules shall be set up. Each entry
shall contain the unique module name, the unique XML namespace from
the YANG URI Scheme and some reference to the module's documentation.
This document registers three URIs for the YANG XML namespace in the
IETF XML registry [RFC3688].
URI: urn:ietf:params:xml:ns:yang:ieee-types
URI: urn:ietf:params:xml:ns:yang:inet-types
URI: urn:ietf:params:xml:ns:yang:yang-types
Schoenwaelder Expires January 15, 2009 [Page 20]
Internet-Draft YANG-TYPES July 2008
7. Security Considerations
This document defines common data types using the YANG data modeling
language. The definitions themselves have no security impact on the
Internet but the usage of these definitions in concrete YANG modules
might have. The security considerations spelled out in the YANG
specification [YANG] apply for this document as well.
Schoenwaelder Expires January 15, 2009 [Page 21]
Internet-Draft YANG-TYPES July 2008
8. Contributors
The following people all contributed significantly to the initial
version of this draft:
- Andy Bierman (andybierman.com)
- Martin Bjorklund (Tail-f Systems)
- Balazs Lengyel (Ericsson)
- David Partain (Ericsson)
- Phil Shafer (Juniper Networks)
Schoenwaelder Expires January 15, 2009 [Page 22]
Internet-Draft YANG-TYPES July 2008
9. Open Issues
- Should YANG allow multiple pattern that get ANDed? This would for
example allow to tighten the IPv6 pattern.
Message-Id: <1215432618.23783.59.camel@missotis>
- Add some common reusable groupings, e.g. a combination of
ip-address and port-number? Or should such groupings be a separate
document?
Schoenwaelder Expires January 15, 2009 [Page 23]
Internet-Draft YANG-TYPES July 2008
10. References
10.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
January 2004.
[YANG] Bjorklund, M., Ed., "YANG - A data modeling language for
NETCONF", draft-ietf-netmod-yang-00 (work in progress).
10.2. Informative References
[RFC4741] Enns, R., "NETCONF Configuration Protocol", RFC 4741,
December 2006.
Schoenwaelder Expires January 15, 2009 [Page 24]
Internet-Draft YANG-TYPES July 2008
Author's Address
Juergen Schoenwaelder (editor)
Jacobs University
Email: j.schoenwaelder@jacobs-university.de
Schoenwaelder Expires January 15, 2009 [Page 25]
Internet-Draft YANG-TYPES July 2008
Full Copyright Statement
Copyright (C) The IETF Trust (2008).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgment
Funding for the RFC Editor function is provided by the IETF
Administrative Support Activity (IASA).
Schoenwaelder Expires January 15, 2009 [Page 26]
| PAFTECH AB 2003-2026 | 2026-04-24 07:27:13 |