One document matched: draft-pan-shared-mesh-protection-02.txt
Differences from draft-pan-shared-mesh-protection-01.txt
IETF Ping Pan
Internet Draft Rajan Rao
Biao Lu
(Infinera)
Luyuan Fang
(Cisco)
Andy Malis
(Verizon)
Sam Aldrin
(Huawei)
Mohana Singamsetty
(Tellabs)
Expires: January 11, 2012 July 11, 2011
Supporting Shared Mesh Protection in MPLS-TP Networks
draft-pan-shared-mesh-protection-02.txt
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79. This document may not be modified,
and derivative works of it may not be created, and it may not be
published except as an Internet-Draft.
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79. This document may not be modified,
and derivative works of it may not be created, except to publish it
as an RFC and to translate it into languages other than English.
This document may contain material from IETF Documents or IETF
Contributions published or made publicly available before November
10, 2008. The person(s) controlling the copyright in some of this
material may not have granted the IETF Trust the right to allow
modifications of such material outside the IETF Standards Process.
Without obtaining an adequate license from the person(s) controlling
the copyright in such materials, this document may not be modified
outside the IETF Standards Process, and derivative works of it may
Pan et.al Expires January 11, 2012 [Page 1]
Internet-Draft Shared Mesh Protection in MPLS-TP July 2011
not be created outside the IETF Standards Process, except to format
it for publication as an RFC or to translate it into languages other
than English.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other documents
at any time. It is inappropriate to use Internet-Drafts as
reference material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
This Internet-Draft will expire on January 11, 2012.
Copyright Notice
Copyright (c) 2011 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with
respect to this document.
Abstract
Shared mesh protection is a common protection and recovery mechanism
in transport networks, where multiple paths can share the same set
of network resources for protection purposes.
In the context of MPLS-TP, it has been explicitly requested as a
part of the overall solution (Req. 67, 68 and 69 in RFC5654 [1]).
It's important to note that each MPLS-TP LSP may be associated with
transport network resources. In event of network failure, it may
require explicit activation on the protecting paths before switching
user traffic over.
Pan et.al Expires January 11, 2012 [Page 2]
Internet-Draft Shared Mesh Protection in MPLS-TP July 2011
In this memo, we define a lightweight signaling mechanism for
protecting path activation in shared mesh protection-enabled MPLS-TP
networks.
Table of Contents
1. Introduction...................................................3
2. Background.....................................................4
3. Problem Definition.............................................5
4. Protection Switching...........................................6
5. Activation Operation Overview..................................8
6. Protocol Definition............................................9
6.1. Activation Messages.......................................9
6.2. Message Encapsulation....................................10
6.3. Reliable Messaging.......................................11
6.4. Message Scoping..........................................12
7. Processing Rules..............................................12
7.1. Enable a protecting path.................................12
7.2. Disable a protecting path................................13
7.3. Get protecting path status...............................14
7.4. Acknowledgement with STATUS..............................14
7.5. Preemption...............................................14
8. Security Consideration........................................14
9. IANA Considerations...........................................15
10. Normative References.........................................15
11. Acknowledgments..............................................15
1. Introduction
Shared mesh protection is a common traffic protection mechanism in
transport networks, where multiple paths can share the same set of
network resources for protection purposes.
In the context of MPLS-TP, it has been explicitly requested as a
part of the overall solution (Req. 67, 68 and 69 in RFC5654 [1]).Its
operation has been further outlined in Section 4.7.6 of MPLS-TP
Survivability Framework [2].
It's important to note that each MPLS-TP LSP may be associated with
transport network resources. In event of network failure, it may
require explicit activation on the protecting paths before switching
user traffic over.
Pan et.al Expires January 11, 2012 [Page 3]
Internet-Draft Shared Mesh Protection in MPLS-TP July 2011
In this memo, we define a lightweight signaling mechanism for
protecting path activation in shared mesh protection-enabled MPLS-TP
networks. The framework version of the document has been presented
in ITU-T SG15 Interim Meeting in May 2011, and is in-sync with the
on-going G.SMP work in ITU-T.
Here are the key design goals:
1. Fast: The protocol is to activate the previously configured
protecting paths in a timely fashion, with minimal transport and
processing overhead. The goal is to support 50msec end-to-end
traffic switch-over in large transport networks.
2. Reliable message delivery: Activation and deactivation operation
have serious impact on user traffic. This requires the protocol to
adapt a low-overhead reliable messaging mechanism. The activation
messages may either traverse through a "trusted" transport
channel, or require some level of built-in reliability mechanism.
3. Modular: Depending on deployment scenarios, the signaling may need
to support functions such as preemption, resource re-allocation
and bi-directional activation in a modular fashion.
Here are some of the conventions used in this document. The key
words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC-2119 [RFC2119].
2. Background
Transport network protection can be typically categorized into three
types:
Cold Standby: In this type of protection, the nodes will only
negotiate and establish backup path after the detection of network
failure.
Hot Standby: The protecting paths are established prior to network
failure. This is also known as "make-before-break". Upon the
detection of network failure, the edge nodes will switch data
traffic into pre-established backup path immediately.
Warm Standby: The nodes will negotiate and reserve protecting path
prior to network failure. However, data forwarding path will not be
programmed. Upon the detection of network failure, the nodes will
Pan et.al Expires January 11, 2012 [Page 4]
Internet-Draft Shared Mesh Protection in MPLS-TP July 2011
send explicit messages to relevant nodes to "wake up" the protecting
path.
The activation signaling defined in this memo is to support warm
standby in the context of MPLS-TP.
Further, the activation procedure may be triggered using the failure
notification methods defined in MPLS-TP OAM specifications.
3. Problem Definition
In this section, we describe the operation of shared mesh protection
in the context of MPLS-TP networks, and outline some of the relevant
definitions.
We refer to the figure below for illustration:
----- B ------- C ----
/ \
/ \
A D
\ /
\ /
==== E === F === G ===
/ \
/ \
H K
\ /
\ /
----- I ------- J ----
Working paths: X = {A, B, C, D}, Y = {H, I, J, K}
Protecting paths: X' = {A, E, F, G, D}, Y' = {H, E, F, G, K}
The links between E, F and G are shared by both protecting paths.
All paths are established via MPLS-TP control plane prior to network
failure.
All paths are assumed to be bi-directional. An edge node is denoted
as a headend or tailend for a particular path in accordance to the
path setup direction.
Pan et.al Expires January 11, 2012 [Page 5]
Internet-Draft Shared Mesh Protection in MPLS-TP July 2011
Initially, the operators setup both working and protecting paths.
During setup, the operators specify the network resources for each
path.
The working path X and Y will configure the appropriate resources on
the intermediate nodes, however, the protecting paths, X' and Y'
will reserve the resources on the nodes, but won't occupy them.
Depending on network planning requirements (such as SRLG), X' and Y'
may share the same set of resources on node E, F and G. The resource
assignment is a part of the control-plane CAC operation taking place
on each node.
At some time, link B-C is cut. Node A will detect the outage, and
initiate activation messages to bring up the protecting path X' The
intermediate nodes, E, F and G will program the switch fabric and
configure the appropriate resources. Upon the completion of the
activation, A will switch the user traffic to X'
The operation may have extra caveat:
1. Preemption: Protecting paths X' and Y' may share the same
resources on node E, F or G due to resource constraints. Y' has
higher priority than that of X' In the previous example, X' is
up and running. When there is a link outage on I-J, H can
activate its protecting path Y' On E, F or G, Y' can take over
the resources from X' for its own traffic. The behavior is
acceptable with the condition that A should be notified about
the preemption action.
2. Over-subscription (1:N): A unit of network resource may be
reserved by one or multiple protecting paths. In the example,
the network resources on E-F and F-G are shared by two
protecting paths, X' and Y' In deployment, the over-
subscription ratio is an important factor on network resource
utilization.
4. Protection Switching
The entire activation and switch-over operation need to be within
the range of milliseconds to meet customer's expectation [1]. This
section illustrates how this may be achieved on MPLS-TP-enabled
transport switches. Note that this is for illustration of protection
switching operation, not mandating the implementation itself.
Pan et.al Expires January 11, 2012 [Page 6]
Internet-Draft Shared Mesh Protection in MPLS-TP July 2011
The diagram below illustrates the operation.
+---------------+
Control | MPLS-TP | Control
<=== Signaling ====| Control Plane |=== Signaling ===>
+---------------+
/ \
/ \ (MPLS label assignment)
/ \
/ \
+-------+ +------+ +-------+
Activation |Line | |Switch| |Line | Activation
<=== Messages ===|Module |===|Fabric|===|Module |=== Messages ===>
+-------+ +------+ +-------+
Typical MPLS-TP user flows (or, LSP's) are bi-directional, and setup
as co-routed or associated tunnels, with a MPLS label for each of
the upstream and downstream traffic. On this particular type of
transport switch, the control-plane can download the labels to the
line modules. Subsequently, the line module will maintain a label
lookup table on all working and protecting paths.
Upon the detection of network failure, the headend nodes will
transmit activation messages along the MPLS LSP's. When receiving
the messages, the line modules can locate the associated protecting
path from the label lookup table, and perform activation procedure
by programming the switching fabric directly. Upon its success, the
line module will swap the label, and forward the activation messages
to the next hop.
In summary, the activation procedure involves efficient path lookup
and switch fabric re-programming.
To achieve the tight end-to-end switch-over budget, it's possible to
implement the entire activation procedure with hardware-assistance
(such as in FPGA or ASIC).
The activation messages are encapsulated with a MPLS-TP Generic
Associated Channel Header (GACH) [3]. Detailed message encoding is
explained in Section 6.
Pan et.al Expires January 11, 2012 [Page 7]
Internet-Draft Shared Mesh Protection in MPLS-TP July 2011
5. Activation Operation Overview
To achieve high performance, the activation procedure is designed to
be simple and straightforward on the network nodes.
In this section, we describe the activation procedure using the same
figure shown before:
----- B ------- C ----
/ \
/ \
A D
\ /
\ /
==== E === F === G ===
/ \
/ \
H K
\ /
\ /
----- I ------- J ----
Working paths: X = {A, B, C, D}, Y = {H, I, J, K}
Protecting paths: X' = {A, E, F, G, D}, Y' = {H, E, F, G, K}
Upon the detection of working path failure, the edge nodes, A, D, H
and K may trigger the activation messages to activate the protecting
paths, and redirect user traffic immediately after.
We assume that there is a consistent definition of priority levels
among the paths throughout the network. At activation time, each
node may rely on the priority levels to potentially preempt other
paths.
When the nodes detect path preemption on a particular node, they
should inform all relevant nodes to free the resources.
To optimize traffic protection and resource management, each headend
may periodically poll the protecting paths about resource
availability. The intermediate nodes have the option to inform the
current resource utilization. This procedure may be conducted by
other OAM mechanisms.
Note that, upon the detection of a working path failure, both
headend and tailend may initiate the activation simultaneously
Pan et.al Expires January 11, 2012 [Page 8]
Internet-Draft Shared Mesh Protection in MPLS-TP July 2011
(known as bi-directional activation). This may expedite the
activation time. However, both headend and tailend nodes need to
coordinate the order of protecting paths for activation, since there
may be multiple protecting paths for each working path (i.e., 1:N
protection). For clarity, we will describe the operation from
headend in the memo. The tailend operation will be available in the
subsequent revisions.
6. Protocol Definition
6.1. Activation Messages
The activation requires the following messages:
o ENABLE: this is initiated by the headend nodes to activate a
protecting path
o DISABLE: this is initiated by the headend nodes to disable a
protecting path and free the associated network resources
o GET: this is initiated by the headend to gather resource
availability information on a particular protecting path
o NOTIFY: this is initiated by the intermediate nodes and terminate
on the headend nodes to report preemption or protection failure
conditions
o STATUS: this is the acknowledgement message for ENABLE, DISABLE,
GET, and NOTIFY messages, and contains the relevant status
information
Each activation message has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Version| Type | Reserved | Seq |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Additional Info |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
o Version: 1
o Type:
Pan et.al Expires January 11, 2012 [Page 9]
Internet-Draft Shared Mesh Protection in MPLS-TP July 2011
o ENABLE 1
o DISABLE 2
o GET 3
o STATUS 4
o NOTIFY 5
o Reserved: This field is reserved for future use
o Seq: This uniquely identifies a particular message. This field is
defined to support reliable message delivery
o Additional Info: the message-specific data
6.2. Message Encapsulation
Activation messages use MPLS labels to identify the paths. Further,
the messages are encapsulated in GAL/GACH:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MPLS Label stack |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| GAL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0 0 0 1|Version| Reserved | Activation Channel Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Activation Message Payload |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
o GAL is described in [3]
o Activation Channel Type is the GACH channel number assigned to
the protocol. This uniquely identifies the activation messages.
Specifically, the messages have the following message format:
Pan et.al Expires January 11, 2012 [Page 10]
Internet-Draft Shared Mesh Protection in MPLS-TP July 2011
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Label | Exp |S| TTL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Label (13) | Exp |S| TTL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0 0 0 1|Version| Reserved | Activation Channel Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Ver(1)| Type | Status Code | Seq |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
For STATUS and NOTIFY messages, the Status Code has the following
encoding value and definition:
o 0-19: OK
. 1: end-to-end ack
o 20-39: message processing errors
. 20: no such path
o 40-59: processing issues:
. 40: no more resource for the path
. 41: preempted by another path
. 42: system failure
o 60-79: informative data:
. 60: shared resource has been taken by other paths
Further, for preemption notification, we may consider of using the
existing MPLS-TP OAM messaging. More details will be available in
the future revisions.
6.3. Reliable Messaging
The activation procedure adapts a simple two-way handshake reliable
messaging.
Pan et.al Expires January 11, 2012 [Page 11]
Internet-Draft Shared Mesh Protection in MPLS-TP July 2011
Each node maintains a sequence number generator. Each new sending
message will have a new sequence number. After sending a message,
the node will wait for a response with the same sequence number.
Specifically, upon the generation of ENABLE, DISABLE, GET and NOTIFY
messages, the message sender expects to receive a STATUS in reply
with same sequence number.
If a sender is not getting the reply (STATUS) within a time
interval, it will retransmit the same message with a new sequence
number, and starts to wait again. After multiple retries (by
default, 3), the sender will declare activation failure, and alarm
the operators for further service.
6.4. Message Scoping
Activation signaling uses MPLS label TTL to control how far the
message would traverse. Here are the processing rules on each
intermediate node:
o On receive, if the message has label TTL = 0, the node must drop
the packet without further processing
o The receiving node must always decrement the label TTL value by
one. If TTL = 0 after the decrement, the node must process the
message. Otherwise, the node must forward the message without
further processing (unless, of course, the node is headend or
tailend)
o On transmission, the node will adjust the TTL value. For hop-by-
hop messages, TTL = 1. Otherwise, TTL = 0xFF, by default.
7. Processing Rules
7.1. Enable a protecting path
Upon the detection of network failure on a working path, the headend
node identifies the corresponding MPLS-TP label and initiates the
protection switching by sending an ENABLE message.
ENABLE messages always use MPLS label TTL = 1 to force hop-by-hop
process. Upon reception, a next-hop node will locate the
corresponding path and activate the path.
Pan et.al Expires January 11, 2012 [Page 12]
Internet-Draft Shared Mesh Protection in MPLS-TP July 2011
If the Enable message is received on an intermediate node, due to
label TTL expiry, the message is processed and then propagated to
the next hop of the MPLS TP LSP, by setting the MPLS TP label TTL =
1. The intermediate node may NOT respond back to the headend node
with STATUS message.
The headend node will declare the success of the activation only
when it gets a positive reply from the tailend node. This requires
that the tailend nodes must reply STATUS messages to the headend
nodes in all cases.
If the headend node is not receiving the acknowledgement within a
time internal, it will retransmit another ENABLE message with a
different Seq number.
If the headend node is not receiving a positive reply within a
longer time interval, it will declare activation failure.
If an intermediate node cannot activate a protecting path, it will
reply an NOTIFY message to report failure. When the headend node
receives a NOTIFY message for failure, it must initiate DISABLE
messages to clean up networks resources on all the relevant nodes on
the path.
7.2. Disable a protecting path
The headend removes the network resources on a path by sending
DISABLE messages.
In the message, the MPLS label represents the path to be de-
activated. The MPLS TTL is one to force hop-by-hop processing.
Upon reception, a node will de-activate the path, by freeing the
resources from the data-plane.
As a part of the clean-up procedure, each DISABLE message must
traverse through and be processed on all the nodes of the
corresponding path. When the DISABLE message reaches to the tailend
node, the tailend is required to reply with a STATUS message to the
headend.
The de-activation process is complete when the headend receives the
corresponding STATUS message from the tailend.
Pan et.al Expires January 11, 2012 [Page 13]
Internet-Draft Shared Mesh Protection in MPLS-TP July 2011
7.3. Get protecting path status
The operators have the option to trigger GET messages from the
headend to check on the protecting path periodically or on-demand.
The process procedure on each node is very similar to that of ENABLE
messages on the intermediate nodes, except the GET messages should
not trigger any network resource re-programming.
Upon reception, the node will check the availability of resources.
If the resource is no longer available, the node will reply a NOTIFY
with error conditions.
7.4. Acknowledgement with STATUS
The STATUS message is the acknowledgement packet to all messages,
and may be generated by any node in the network.
Each STATUS message must use the same sequence number as the
corresponding message (ENABLE, DISABLE, GET and NOTIFY).
When replying to headend, the tailend nodes must originate STATUS
messages with a large MPLS TTL value (0xff, by default).
7.5. Preemption
The preemption operation typically takes place when processing an
ENABLE message.
If the activating network resources have been used by another path
and carrying user traffic, the node needs to compare the priority
levels.
If the existing path has higher priority, the node needs to reject
the ENABLE message by sending a STATUS message to the corresponding
headend to inform the unavailability of network resources.
If the new path has higher priority, the node will reallocate the
resource to the new path, and send an NOTIFY message to old path's
headend node to inform about the preemption.
8. Security Consideration
The protection activation takes place in a controlled networking
environment. Nevertheless, it is expected that the edge nodes will
encapsulate and transport external traffic into separated tunnels,
and the intermediate nodes will never have to process them.
Pan et.al Expires January 11, 2012 [Page 14]
Internet-Draft Shared Mesh Protection in MPLS-TP July 2011
9. IANA Considerations
Activation messages are encapsulated in MPLS-TP with a specific GACH
channel type that needs to be assigned by IANA.
10. Normative References
[1] RFC 5654: Requirements of an MPLS Transport Profile, B. Niven-
Jenkins, D. Brungard, M. Betts, N. Sprecher, S. Ueno,
September 2009
[2] IETF draft, Multiprotocol Label Switching Transport Profile
Survivability Framework (draft-ietf-mpls-tp-survive-fwk-
06.txt), N. Sprecher, A. Farrel, June 2010
[3] RFC5586 - Vigoureux,, M., Bocci, M., Swallow, G., Aggarwal,
R., and D. Ward, "MPLS Generic Associated Channel", May 2009.
[4] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[5] Crocker, D. and Overell, P.(Editors), "Augmented BNF for
Syntax Specifications: ABNF", RFC 2234, Internet Mail
Consortium and Demon Internet Ltd., November 1997.
11. Acknowledgments
Authors like to thank Eric Osborne, Lou Berger, Nabil Bitar and
Deborah Brungard for detailed feedback on the earlier work, and the
guidance and recommendation for this proposal.
We also thank Maneesh Jain, Mohit Misra, Yalin Wang, Ted Sprague,
Ann Gui and Tony Jorgenson for discussion on network operation,
feasibility and implementation methodology.
During ITU-T SG15 Interim meeting in May 2011, we have had long
discussion with the G.SMP contributors, in particular Fatai Zhang,
Bin Lu, Maarten Vissers and Jeong-dong Ryoo. We thank their feedback
and corrections.
Pan et.al Expires January 11, 2012 [Page 15]
Internet-Draft Shared Mesh Protection in MPLS-TP July 2011
Authors' Addresses
Ping Pan
Email: ppan@infinera.com
Rajan Rao
Email: rrao@infinera.com
Biao Lu
Email: blu@infinera.com
Luyuan Fang
Email: lufang@cisco.com
Andy Malis
Email: andrew.g.malis@verizon.com
Sam Aldrin
Email: sam.aldrin@huawei.com
Sri Mohana Satya Srinivas Singamsetty
Email: SriMohanS@Tellabs.com
Pan et.al Expires January 11, 2012 [Page 16]
| PAFTECH AB 2003-2026 | 2026-04-24 00:59:29 |