One document matched: draft-mrw-trill-over-ip-02.txt
Differences from draft-mrw-trill-over-ip-01.txt
Network Working Group M. Wasserman
Internet-Draft Painless Security
Intended status: Standards Track D. Eastlake
Expires: March 10, 2013 Huawei R&D USA
D. Zhang
Huawei Technologies
September 6, 2012
Transparent Interconnection of Lots of Links (TRILL) over IP
draft-mrw-trill-over-ip-02.txt
Abstract
The Transparent Interconnection of Lots of Links (TRILL) protocol is
implemented by devices called Routing Bridges (RBridges). TRILL
supports both point-to-point and multi-access links and is designed
so that a variety of link protocols can be used between RBridge
ports. This document standardizes methods for encapsulating TRILL in
UDP/IP(v4 or v6) to provide a unified TRILL campus.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on March 10, 2013.
Copyright Notice
Copyright (c) 2012 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
Wasserman, et al. Expires March 10, 2013 [Page 1]
Internet-Draft TRILL over IP September 2012
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Requirements Terminology . . . . . . . . . . . . . . . . . . . 3
2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Use Cases for TRILL over IP . . . . . . . . . . . . . . . . . 3
3.1. Remote Office Scenario . . . . . . . . . . . . . . . . . . 4
3.2. IP Backbone Scenario . . . . . . . . . . . . . . . . . . . 4
3.3. Important Properties of the Scenarios . . . . . . . . . . 4
3.3.1. Security Requirements . . . . . . . . . . . . . . . . 4
3.3.2. Multicast Handling . . . . . . . . . . . . . . . . . . 5
3.3.3. RBridge Discovery . . . . . . . . . . . . . . . . . . 5
4. TRILL Frame Formats . . . . . . . . . . . . . . . . . . . . . 5
4.1. TRILL Data Frame . . . . . . . . . . . . . . . . . . . . . 6
4.2. TRILL IS-IS Frame . . . . . . . . . . . . . . . . . . . . 6
5. Link Protocol Specifics . . . . . . . . . . . . . . . . . . . 6
6. Port Configuration . . . . . . . . . . . . . . . . . . . . . . 7
7. TRILL over UDP/IP Format . . . . . . . . . . . . . . . . . . . 7
8. Handling Multicast . . . . . . . . . . . . . . . . . . . . . . 7
8.1. Multicast of TRILL IS-IS Packets . . . . . . . . . . . . . 8
8.2. Multicast Data Frames . . . . . . . . . . . . . . . . . . 8
9. Use of DTLS . . . . . . . . . . . . . . . . . . . . . . . . . 8
10. Transport Considerations . . . . . . . . . . . . . . . . . . . 8
10.1. Recursive Encapsulation . . . . . . . . . . . . . . . . . 8
11. MTU Considerations . . . . . . . . . . . . . . . . . . . . . . 9
12. Middlebox Considerations . . . . . . . . . . . . . . . . . . . 9
13. Security Considerations . . . . . . . . . . . . . . . . . . . 10
14. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 10
15. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 11
16. References . . . . . . . . . . . . . . . . . . . . . . . . . . 11
16.1. Normative References . . . . . . . . . . . . . . . . . . . 11
16.2. Informative References . . . . . . . . . . . . . . . . . . 12
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 12
Wasserman, et al. Expires March 10, 2013 [Page 2]
Internet-Draft TRILL over IP September 2012
1. Requirements Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
2. Introduction
RBridges are devices that implement the IETF TRILL protocol [RFC6325]
[RFC6326] [RFC6327].
RBridges provide transparent forwarding of frames within an arbitrary
network topology, using least cost paths for unicast traffic. They
support VLANs and multipathing of unicast and multi-destination
traffic. They use IS-IS link state routing and encapsulation with a
hop count. The are compatible with IEEE 802.1 customer bridges, and
can incrementally replace them.
Two or more RBridges can communicate over a variety of different link
types, such as Ethernet [RFC6325] or PPP [RFC6361].
This document defines a method for RBridges to communicate over UPD/
IP(v4 or v6). TRILL over IP will allow remote, Internet-connected
RBridges to form a single RBridge campus, or multiple TRILL over IP
networks within a campus to be connected as a single TRILL campus via
a TRILL over IP backbone.
TRILL over IP connects RBridge ports using IPv4 or IPv6 as a
transport in such a way that the ports appear to TRILL to be
connected by a single link. The link will be a multi-access link if
more than two RBridge ports are connected via a single TRILL over IP
link, so that any pair of ports can communicate.
To support cases where RBridges are connected via links (such as the
public Internet) that are not under the same administrative control
as the TRILL campus, this document specifies the use of Datagram
Transport Layer Security (DTLS) [RFC4327] to secure communication
between RBridges running TRILL over IP.
3. Use Cases for TRILL over IP
In this document, we consider two use cases that are typical of
situations where network administrators may choose to use TRILL over
an IP network: a remote office scenario, and an IP backbone scenario.
Wasserman, et al. Expires March 10, 2013 [Page 3]
Internet-Draft TRILL over IP September 2012
3.1. Remote Office Scenario
In the Remote Office Scenario, a remote TRILL network is connected to
a TRILL campus across a multihop non-TRILL IP network, such as the
public Internet. The TRILL network in the remote office becomes a
logical part of TRILL campus, and nodes in the remote office can be
attached to the same VLANs as local campus nodes. In many cases, a
remote office may be attached to the TRILL campus by a single pair of
RBridges, one on the campus end, and the other in the remote office.
In this use case, the TRILL over IP link will often cross logical and
physical IP networks that do not support TRILL, and are not under the
same administrative control as the TRILL campus.
3.2. IP Backbone Scenario
In the IP Backbone Scenario, TRILL over IP is used to connect a
number of TRILL networks to form a single TRILL campus. For example,
a TRILL over IP backbone could be used to connect multiple TRILL
networks on different floors of a large building, or to connect TRILL
networks in separate buildings of a multi-building site. In this use
case, there may often be several TRILL RBridges on a single TRILL
over IP link, and the IP link(s) used by TRILL over IP are typically
under the same administrative control as the rest of the TRILL
campus.
3.3. Important Properties of the Scenarios
There are a number of differences between the two scenarios listed
above, some of which drive features of this specification. These
differences are especially pertinent to the security requirements of
the solution, how multicast data frames are handled, and how the
RBridges discover each other.
3.3.1. Security Requirements
In the IP Backbone Scenario, TRILL over IP is used between a number
of RBridges, on a network link that is in the same administrative
control as the remainder of the TRILL campus. While it is desirable
in this scenario to prevent the association of rogue RBridges, this
can be accomplished using existing IS-IS security mechanisms. There
may be no need to protect the data traffic, beyond any protections
that are already in place on the local network.
In the Remote Office Scenario, TRILL over IP may run over a network
that is not under the same administrative control as the TRILL
network. Nodes on the network may think that they are sending
traffic locally, while that traffic is actually being sent, in a
UDP/IP tunnel, over the public Internet. It is necessary in this
Wasserman, et al. Expires March 10, 2013 [Page 4]
Internet-Draft TRILL over IP September 2012
scenario to protect user privacy, as well as ensuring that no
unauthorized RBridges can gain access to the RBridge campus. The
data privacy requirement is addressed by the use of DTLS for both
IS-IS frames and data frames between RBridges in this scenario.
3.3.2. Multicast Handling
In the IP Backbone scenario, native mutlicast may be supported on the
TRILL over IP link. If so, it will be used to send TRILL IS-IS and
multicast data frames, as discussed later in this document.
In the Remote Office Scenario, there will often be only one pair of
RBridges connecting a given site, and even when multiple RBridges are
used to connect a Remote Office to the TRILL campus, the intervening
network may not provide reliable (or any) multicast connectivity.
Also, it is difficult to provide strong data privacy for multicast
traffic. For all of these reasons, the connections between local and
remote RBridges will be treated like point-to-point links, and all
TRILL IS-IS control messages and multicast data frames that are
transmitted between the Remote Office and the TRILL campus will be
serialized, as discussed later in this document.
3.3.3. RBridge Discovery
In the IP Backbone Scenario, RBridges that use TRILL over IP will use
the normal TRILL IS-IS Hello mechanisms to discover the existence of
other RBridges on the link [RFC6327], and to establish authenticated
communication with those RBridges.
In the Remote Office Scenario, a DTLS session will need to be
established between RBridges before TRILL IS-IS traffic can be
exchanged, as discussed below. In this case, one of the RBRidges
will need to be configured to establish a DTLS session with the other
RBridge. This will typically be accomplished by configuring the
RBridge at a Remote Office to initiate a DTLS session, and subsequent
TRILL exchanges, with a TRILL over IP-enabled RBridge attached to the
TRILL campus.
4. TRILL Frame Formats
To support the TRILL base protocol standard [RFC6325]. , two types of
frames will be transmitted between RBridges: TRILL Data frames and
TRILL IS-IS frames.
Wasserman, et al. Expires March 10, 2013 [Page 5]
Internet-Draft TRILL over IP September 2012
4.1. TRILL Data Frame
The on-the-wire form of a TRILL Data frame in transit between two
neighboring RBridges is as shown below:
+--------------+----------+----------------+-----------+
| TRILL Data | TRILL | Encapsulated | Link |
| Link Header | Header | Native Frame | Trailer |
+--------------+----------+----------------+-----------+
Where the Encapsulated Native Frame is in Ethernet frame format with
a VLAN tag but with no trailing Frame Check Sequence (FCS).
4.2. TRILL IS-IS Frame
TRILL IS-IS frames are formatted on-the-wire as follows:
+--------------+---------------+-----------+
| TRILL IS-IS | TRILL IS-IS | Link |
| Link Header | Payload | Trailer |
+--------------+---------------+-----------+
The Link Header and Link Trailer in these formats depend on the
specific link technology. The Link Header usually contains one or
more fields that distinguish TRILL Data from TRILL IS-IS. For
example, over Ethernet, the TRILL Data Link Header ends with the
TRILL Ethertype while the TRILL IS-IS Link Header ends with the L2-
IS-IS Ethertype; on the other hand, over PPP, there are no Ethertypes
but PPP protocol code points are included that distinguish TRILL Data
from TRILL IS-IS.
In TRILL over IP, we will use UDP/IP (v4 or v6) as the link header,
and the TRILL frame type will be determined based on the UDP port
number. In TRILL over IP, no Link Trailer is specified, although one
may be added when the resulting IP packets are encapsulated for
transmission on a network (e.g. Ethernet).
5. Link Protocol Specifics
TRILL Data packets can be unicast to a specific RBridge or multicast
to all RBridges on the link. TRILL IS-IS packets are always
multicast to all other RBridge on the link (except for TRILL IS-IS
MTU PDUs, which may be unicast). On Ethernet links, the Ethernet
Wasserman, et al. Expires March 10, 2013 [Page 6]
Internet-Draft TRILL over IP September 2012
multicast address All-RBridges is used for TRILL Data and All-IS-IS-
RBridges for TRILL IS-IS.
To properly handle TRILL base protocol frames on a TRILL over IP
link, either native multicast mode must be enabled on that link, or
multicast must be simulated using serial unicast, as discussed below.
In TRILL Hello PDUs used on TRILL IP links, the IP addresses of the
connected IP ports are their SNPA addresses. Thus, all TRILL
Neighbor TLVs in such Hellos MUST specify that the size of the SNPA
is 4-bytes for an IPv4 link or 16-bytes for an IPv6 link
[rfc6326bis]. Note that SNPA addresses and their size are
independent of TRILL System IDs which are 6-bytes.
6. Port Configuration
Each RBridge port used for a TRILL over IP link MUST have at least
one IP (v4 or v6) address. Implementations MAY allow a single
physical port to operate as multiple IPv4 and/or IPv6 logical ports.
TBD: MUST be able to configure list of IP addresses for serial
unicast. MUST be able to configure non-standard IP multi-cast
addresses.
7. TRILL over UDP/IP Format
The general format of a TRILL over UDP/IP packet is shown below.
+----------+--------+-----------------------+
| IP | UDP | TRILL |
| Header | Header | Payload |
+----------+--------+-----------------------+
Where the UDP Header is as follows:
TBD
8. Handling Multicast
Wasserman, et al. Expires March 10, 2013 [Page 7]
Internet-Draft TRILL over IP September 2012
8.1. Multicast of TRILL IS-IS Packets
By default, TRILL IS-IS packets are sent to an IPv4 multicast
address.
8.2. Multicast Data Frames
TBD
9. Use of DTLS
All RBridges that support TRILL over IP MUST implement DTLS and
support the use of DTLS to secure both TRILL IS-IS and data traffic.
When DTLS is used to secure a TRILL over IP link, the DTLS session
MUST be fully established before any TRILL IS-IS or data frames are
exchanged.
RBridges that implement TRILL over IP MUST support the use of
certificates for DTLS, and MUST support the following algorithm:
o TLS_RSA_WITH_AES_128_CBC_SHA [RFC5246]
RBridges that support TRILL over IP MAY support the use of pre-shared
keys for DTLS. If the communicating RBridges have IS-IS
authentication enabled with a pre-shared key, then that key may be
used for DTLS unless some other pre-shared key is configured. If
pre-shared keys are supported, the following cryptographic algorithms
MUST be supported for use with pre-shared keys:
o TLS_PSK_WITH_AES_128_CBC_SHA [RFC5246]
10. Transport Considerations
10.1. Recursive Encapsulation
TRILL is designed to transport end station Ethernet traffic and IP is
frequently transported over Ethernet. Thus, an end station Ethernet
frame EF might get TRILL encapsulated to TRILL(EF) which was then
send on a TRILL over IP over Ethernet link resulting in an Ethernet
frame of the form Ethernet(IP(TRILL(EF))). There is a risk of such
an Ethernet frame being re-ingressed by the same TRILL campus, due to
physical or logical misconfiguration, looping round, being further
encapsulated and re-ingressed, etc. The frame might get discarded if
it got too large but if fragmentation is enabled, it would just keep
getting split into fragment that would continue to loop and grow and
re-fragment until the path was saturated with junk and frames were
Wasserman, et al. Expires March 10, 2013 [Page 8]
Internet-Draft TRILL over IP September 2012
being discarded due to queue overflow. TTL would provide no
protection because each TRILL encapsulation adds a new TTL.
To protect against this scenario, TRILL over IP output ports MUST be
able to test whether a TRILL frame they are above to send is, in fact
a TRILL encapsulation of a TRILL over IP over Ethernet frame. That
is, is it of the form TRILL(Ethernet(IP(TRILL(...))). If so, the
default action of the TRILL over IP output port is to discard the
frame. However, there are cases where some level of multiple
encapsulations is desired so it MUST be possible to configure the
port to allow such frames.
11. MTU Considerations
In TRILL each RBridge advertises the largest LSP frame it can accept
(but not less than 1,470 bytes) on any of its interfaces (at least
those interfaces with adjacencies to other RBridges in the campus) in
its LSP number zero through the originatingLSPBufferSize TLV
[RFC6325] [rfc6326bis]. The campus minimum MTU, denoted Sz, is then
established by taking the minimum of this advertised MTU for all
RBridges in the campus. Links that do not meet the Sz MTU are not
included in the routing topology. This protects the operation of
IS-IS from links that would be unable to accommodate some LSPs.
Exact methods of determining originatingLSPBufferSize for an RBridge
with one or more TRILL over IP ports are beyond the scope of this
document. However, if an IP link either can accommodate jumbo frames
or is a link on which IP fragmentation is enabled and acceptable,
then it is unlikely that the IP link will be a constraint on the
RBridge's originatingLSPBufferSize. On the other hand, if the IP
link can only handle smaller frames and fragmentation is to be
avoided when possible, a TRILL over IP port might constrain the
RBridge's originatingLSPBufferSize. Because TRILL sets the minimum
values of Sz at 1,470 bytes, there may be links that meet the minimum
MTU for the IP protocol (1,280 bytes for IPv6, theoretically 68 bytes
for IPv4) on which it would be necessary to enable fragmentation for
TRILL use.
The optional use of TRILL IS-IS MTU PDUs, as specified in [RFC6325]
and [RFC6327] can provide added assurance of the actual MTU of a
link.
12. Middlebox Considerations
TBD
Wasserman, et al. Expires March 10, 2013 [Page 9]
Internet-Draft TRILL over IP September 2012
13. Security Considerations
TRILL over IP is subject to all of the security considerations for
the base TRILL protocol. In addition, there are specific security
requirements for different TRILL deployment scenarios, as discussed
in the "Use Cases for TRILL over IP" section above.
This document specifies that all RBridges that support TRILL over IP
MUST implement DTLS, and makes it clear that it is both wise and good
to use DTLS in all cases where a TRILL over IP link will traverse a
network that is not under the same administrative control as the rest
of the TRILL campus. DTLS is necessary, in these cases to protect
the privacy and integrity of data traffic.
TRILL over IP is completely compatible with the use of IS-IS
security, which can be used to authenticte RBridges before allowing
them to join a TRILL campus. This is sufficient to protect against
rogue RBridges, but is not sufficient to protect data frames that may
be sent, in UDP/IP tunnels, outside of the local network, or even
across the public Internet. To protect the privacy and integrity of
that traffic, use DTLS.
In cases were DTLS is used, the use of IS-IS security may not be
necessary, but there is nothing about this specification that would
prevent using both DTLS and IS-IS security together. In cases where
both types of security are enabled, implementations MAY allow users
to configure a single shared key that will be used for both
mechanisms.
14. IANA Considerations
IANA has allocated the following UDP Ports for the TRILL IS-IS and
Data channels:
UDP Port Protocol
(TBD) TRILL IS-IS Channel
(TBD) TRILL Data Channel
IANA has allocated one IPv4 and one IPv6 multicast address, as shown
below, which correspond to the All-RBridges and All-IS-IS-RBridges
multicast MAC addresses that the IEEE Registration Authority has
assigned for TRILL. Because the low level hardware MAC address
dispatch considerations for TRILL over Ethernet do not apply to TRILL
over IP, one IP multicast address for each version of IP is
Wasserman, et al. Expires March 10, 2013 [Page 10]
Internet-Draft TRILL over IP September 2012
sufficient.
[Values recommended to IANA:]
Name IPv4 IPv6
All-RBridges 233.252.14.0 FF0X:0:0:0:0:0:0:205
Note: when these IPv4 and IPv6 multicast addresses are used and the
resulting IP frame is sent over Ethernet, the usual IP derived MAC
address is used.
[Need to discuss scopes for IPv6 multicast (the "X" in the addresses)
somewhere. Default to "site" scope but MUST be configurable?]
15. Acknowledgements
This document was written using the xml2rfc tool described in RFC
2629 [RFC2629].
The following people have provided useful feedback on the contents of
this document: Sam Hartman.
16. References
16.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC4327] Dubuc, M., Nadeau, T., Lang, J., and E. McGinnis, "Link
Management Protocol (LMP) Management Information Base
(MIB)", RFC 4327, January 2006.
[RFC5246] Dierks, T. and E. Rescorla, "The Transport Layer Security
(TLS) Protocol Version 1.2", RFC 5246, August 2008.
[RFC6325] Perlman, R., Eastlake, D., Dutt, D., Gai, S., and A.
Ghanwani, "Routing Bridges (RBridges): Base Protocol
Specification", RFC 6325, July 2011.
[RFC6326] Eastlake, D., Banerjee, A., Dutt, D., Perlman, R., and A.
Ghanwani, "Transparent Interconnection of Lots of Links
(TRILL) Use of IS-IS", RFC 6326, July 2011.
Wasserman, et al. Expires March 10, 2013 [Page 11]
Internet-Draft TRILL over IP September 2012
[RFC6327] Eastlake, D., Perlman, R., Ghanwani, A., Dutt, D., and V.
Manral, "Routing Bridges (RBridges): Adjacency", RFC 6327,
July 2011.
16.2. Informative References
[RFC2629] Rose, M., "Writing I-Ds and RFCs using XML", RFC 2629,
June 1999.
[RFC6361] Carlson, J. and D. Eastlake, "PPP Transparent
Interconnection of Lots of Links (TRILL) Protocol Control
Protocol", RFC 6361, August 2011.
Authors' Addresses
Margaret Wasserman
Painless Security
356 Abbott Street
North Andover, MA 01845
USA
Phone: +1 781 405-7464
Email: mrw@painless-security.com
URI: http://www.painless-security.com
Donald Eastlake
Huawei R&D USA
155 Beaver Street
Milford, MA 01757
USA
Phone: +1 508 333-2270
Email: d3e3e3@gmail.com
Dacheng Zhang
Huawei Technologies
Q14, Huawei Campus
No.156 Beiqing Rd.
Beijing, Hai-Dian District 100095
P.R. China
Phone:
Email: zhangdacheng@huawei.com
URI:
Wasserman, et al. Expires March 10, 2013 [Page 12]
| PAFTECH AB 2003-2026 | 2026-04-24 01:58:40 |