One document matched: draft-ietf-tewg-diff-te-russian-02.txt
Differences from draft-ietf-tewg-diff-te-russian-01.txt
Francois Le Faucheur, Editor
Cisco Systems, Inc.
IETF Internet Draft
Expires: September, 2003
Document: draft-ietf-tewg-diff-te-russian-02.txt March, 2003
Russian Dolls Bandwidth Constraints Model for
Diff-Serv-aware MPLS Traffic Engineering
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026. Internet-Drafts are
Working documents of the Internet Engineering Task Force (IETF), its
areas, and its working groups. Note that other groups may also
distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Abstract
This document provides specification for one Bandwidth Constraints
model for Diff-Serv-aware MPLS Traffic Engineering, which is referred
to as the Russian Dolls Model.
Summary for Sub-IP related Internet Drafts
RELATED DOCUMENTS:
draft-ietf-tewg-diff-te-reqts-06.txt
draft-ietf-tewg-diff-te-proto-02.txt
WHERE DOES IT FIT IN THE PICTURE OF THE SUB-IP WORK
This ID is a Working Group document of the TE Working Group.
WHY IS IT TARGETED AT THIS WG(s)
TEWG is responsible for specifying protocol extensions for support of
Diff-Serv-aware MPLS Traffic Engineering.
Le Faucheur, et. al 1
Russian Dolls model for DS-TE March 2003
JUSTIFICATION
The TEWG charter states that "This will entail verification and
review of the Diffserv requirements in the WG Framework document and
initial specification of how these requirements can be met through
use and potentially expansion of existing protocols."
In line with this, the TEWG is specifying bandwidth constraints model
for Diff-Serv-aware MPLS Traffic Engineering. This document describes
one particular bandwidth constraints model.
Specification of Requirements
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
1. Introduction
[DSTE-REQ] presents the Service Providers requirements for support of
Diff-Serv-aware MPLS Traffic Engineering (DS-TE). This includes the
fundamental requirement to be able to enforce different bandwidth
constraints for different classes of traffic.
[DSTE-REQ] also defines the concept of Bandwidth Constraint Models
for DS-TE and states that "The DS-TE technical solution MUST specify
at least one bandwidth constraint model and MAY specify multiple
bandwidth constraint."
This document provides a detailed description of one particular
Bandwidth Constraint model for DS-TE which is introduced in [DSTE-
REQ] and called the Russian Dolls Model (RDM).
[DSTE-PROTO] specifies the IGP and RSVP-TE signaling extensions for
support of DS-TE. These extensions support RDM.
2. Contributing Authors
This document was the collective work of several. The text and
content of this document was contributed by the editor and the co-
authors listed below. (The contact information for the editor appears
in Section 11, and is not repeated below.)
Jim Boyle Kireeti Kompella
Protocol Driven Networks, Inc. Juniper Networks, Inc.
1381 Kildaire Farm Road #288 1194 N. Mathilda Ave.
Cary, NC 27511, USA Sunnyvale, CA 94099
Phone: (919) 852-5160 Email: kireeti@juniper.net
Email: jboyle@pdnets.com
Le Faucheur et. al 2
Russian Dolls model for DS-TE March 2003
William Townsend Thomas D. Nadeau
Tenor Networks Cisco Systems, Inc.
100 Nagog Park 250 Apollo Drive
Acton, MA 01720 Chelmsford, MA 01824
Phone: +1-978-264-4900 Phone: +1-978-244-3051
Email: Email: tnadeau@cisco.com
btownsend@tenornetworks.com
Darek Skalecki
Nortel Networks
3500 Carling Ave,
Nepean K2H 8E9
Phone: +1-613-765-2252
Email: dareks@nortelnetworks.com
3. Definitions
For readability a number of definitions from [DSTE-REQ] are repeated
here:
Class-Type (CT): the set of Traffic Trunks crossing a link that is
governed by a specific set of Bandwidth Constraints. CT is used for
the purposes of link bandwidth allocation, constraint based routing
and admission control. A given Traffic Trunk belongs to the same CT
on all links.
TE-Class: A pair of:
i. a Class-Type
ii. a preemption priority allowed for that Class-Type. This
means that an LSP transporting a Traffic Trunk from
that Class-Type can use that preemption priority as the
set-up priority, as the holding priority or both.
Reserved (CTc) : For a given Class-Type CTc ( 0 <= c <= MaxCT ) ,let
us define "Reserved(CTc)" as the sum of the bandwidth reserved by all
established LSPs which belong to CTc.
The following definition from [DSTE-PROTO] is also repeated here:
Normalised(CTc) : let us define "Normalised(CTc)" as
"Reserved(CTc)/LOM(c)", where LOM (c) is the Local Overbooking
Multiplier for CTc defined in [DSTE-PROTO].
We also introduce the following definitions:
Reserved(CTb,q) : let us define "Reserved(CTb,q)" as the sum of the
bandwidth reserved by all established LSPs which belong to CTb and
have a holding priority of q. Note that if q and CTb do not form one
of the 8 possible configured TE-Classes, then there can not be any
Le Faucheur et. al 3
Russian Dolls model for DS-TE March 2003
established LSP which belong to CTb and have a holding priority of q,
so in that case Reserved(CTb,q)=0.
Normalised(CTc,q) : let us define "Normalised(CTc,q)" as
"Reserved(CTc/q) / LOM(c)", where LOM (c) is the Local Overbooking
Multiplier for CTc defined in [DSTE-PROTO].
4. Russian Dolls Model Definition
RDM is defined in the following manner (assuming for now that the
optional per-CT Local Overbooking Multipliers defined in [DSTE-PROTO]
are not used - i.e. LOM[c]=1 , 0<=c<=7 ):
o Maximum Number of Bandwidth Constraints (MaxBC)= Maximum
Number of Class-Types (MaxCT) = 8
o for each value of b in the range 0 <= b <= (MaxCT - 1):
SUM (Reserved (CTc)) <= BCb,
for all "c" in the range b <= c <= (MaxCT - 1)
A DS-TE LSR implementing RDM MUST support enforcement of bandwidth
constraints in compliance with this definition.
Where 8 Class-Types are active, the RDM bandwidth constraints can
also be expressed in the following way:
- All LSPs from CT7 use no more than BC7
- All LSPs from CT6 and CT7 use no more than BC6
- All LSPs from CT5, CT6 and CT7 use no more than BC5
- etc.
- All LSPs from CT0, CT1,... CT7 use no more than BC0
Le Faucheur et. al 4
Russian Dolls model for DS-TE March 2003
Purely for illustration purposes, the diagram below represents the
Russian Doll Bandwidth Constraints model in a pictorial manner when 3
Class-Types are active:
I------------------------------------------------------I
I-------------------------------I I
I--------------I I I
I CT2 I CT2+CT1 I CT2+CT1+CT0 I
I--------------I I I
I-------------------------------I I
I------------------------------------------------------I
I-----BC2------>
I----------------------BC1------>
I---------------------------------------------BC0------>
While simpler Bandwidth Constraints models (see [MAM]) or,
conversely, more flexible/sophisticated Bandwidth Constraints models
can be defined, the Russian Dolls Model is attractive in some DS-TE
environments for the following reasons:
- Although less intuitive than MAM, RDM is still a simple model
to conceptualize.
- RDM can be used to simultaneously ensure bandwidth efficiency
and protection against QoS degradation of all Class-Types,
whether preemption is used or not.
- RDM can be used in conjunction with preemption to
simultaneously achieve isolation across Class-Types (so that
each Class-Type is guaranteed its share of bandwidth no
matter the level of contention by other classes), bandwidth
efficiency and protection against QoS degradation of all
Class-Types.
- RDM only requires limited protocol extensions such as the
ones defined in [DSTE-PROTO].
RDM may not be attractive in some DS-TE environments for the
following reasons:
- if the usage of preemption is precluded for some
administrative reason, while RDM can still ensure bandwidth
efficiency and protection against QoS degradation of all CTs,
RDM cannot guarantee isolation across Class-Types.
Additional considerations on the properties of RDM can be found in
[BC-CONS] and [BC-MODEL].
As a simple example usage of the "Russian Doll" Bandwidth Constraints
Model, a network administrator using one CT for Voice (CT1) and one
CT for data (CT0) might configure on a given link:
- BC0 = 2.5 Gb/s (i.e. Voice + Data is limited to 2.5 Gb/s)
- BC1= 1.5 Gb/s (i.e. Voice is limited to 1.5 Gb/s).
Le Faucheur et. al 5
Russian Dolls model for DS-TE March 2003
5. Example Formulas for Computing "Unreserved TE-Class [i]" with
Russian Dolls Model
As specified in [DSTE-PROTO], formulas for computing "Unreserved TE-
Class [i]" MUST reflect all of the Bandwidth Constraints relevant to
the CT associated with TE-Class[i], and thus, depend on the Bandwidth
Constraints Model. Thus, a DS-TE LSR implementing RDM MUST reflect
the RDM bandwidth constraints defined in section 4 above when
computing "Unreserved TE-Class [i]".
Keeping in mind, as explained in [DSTE-PROTO], that details of
admission control algorithms as well as formulas for computing
"Unreserved TE-Class [i]" are outside the scope of the IETF work, we
provide in this section, for illustration purposes, an example of how
values for the unreserved bandwidth for TE-Class[i] might be computed
with RDM, assuming:
- the basic admission control algorithm which simply deducts
the exact bandwidth of any established LSP from all of the
Bandwidth Constraints relevant to the CT associated with that
LSP.
- the optional per-CT Local Overbooking Multipliers are not
used (.i.e. LOM[c]=1, 0<= c <=7).
We assume that:
TE-Class [i] <--> < CTc , preemption p>
in the configured TE-Class mapping.
For readability, formulas are first shown assuming only 4 CTs are
active. The formulas are then extended to cover the cases where more
CTs are used.
If CTc = CT0, then "Unreserved TE-Class [i]" =
[ BC0 - SUM ( Reserved(CTb,q) ) ] for q <= p and 0 <= b <= 3
If CTc = CT1, then "Unreserved TE-Class [i]" =
MIN [
[ BC1 - SUM ( Reserved(CTb,q) ) ] for q <= p and 1 <= b <= 3,
[ BC0 - SUM ( Reserved(CTb,q) ) ] for q <= p and 0 <= b <= 3
]
If CTc = CT2, then "Unreserved TE-Class [i]" =
MIN [
[ BC2 - SUM ( Reserved(CTb,q) ) ] for q <= p and 2 <= b <= 3,
[ BC1 - SUM ( Reserved(CTb,q) ) ] for q <= p and 1 <= b <= 3,
[ BC0 - SUM ( Reserved(CTb,q) ) ] for q <= p and 0 <= b <= 3
]
If CTc = CT3, then "Unreserved TE-Class [i]" =
Le Faucheur et. al 6
Russian Dolls model for DS-TE March 2003
MIN [
[ BC3 - SUM ( Reserved(CTb,q) ) ] for q <= p and 3 <= b <= 3,
[ BC2 - SUM ( Reserved(CTb,q) ) ] for q <= p and 2 <= b <= 3,
[ BC1 - SUM ( Reserved(CTb,q) ) ] for q <= p and 1 <= b <= 3,
[ BC0 - SUM ( Reserved(CTb,q) ) ] for q <= p and 0 <= b <= 3
]
The formula can be generalized to 8 active CTs and expressed in a
more compact way in the following:
"Unreserved TE-Class [i]" =
MIN [
[ BCc - SUM ( Reserved(CTb,q) ) ] for q <= p and c <= b <= 7,
. . .
[ BC0 - SUM ( Reserved(CTb,q) ) ] for q <= p and 0 <= b <= 7,
]
where:
TE-Class [i] <--> < CTc , preemption p>
in the configured TE-Class mapping.
6. Support of Optional Local Overbooking Method
We remind the reader that, as discussed in [DSTE-PROTO], the
"LSP/link size overbooking" method (which does not use the Local
Overbooking Multipliers - LOMs-) is expected to be sufficient in many
DS-TE environments. It is expected that the optional Local
Overbooking method (and LOMs) would only be used in specific
environments, in particular where different overbooking ratios need
to be enforced on different links of the DS-TE domain and cross-
effect of overbooking across CTs needs to be accounted for very
accurately.
This section discusses the impact of the optional local overbooking
method on RDM and associated rules and formula. This is only
applicable in the cases where the optional local overbooking method
is indeed supported by the DS-TE LSRs and actually deployed.
6.1. Russian Dolls Model Definition With Local Overbooking
As specified in [DSTE-PROTO], when the optional Local Overbooking
method is supported, the bandwidth constraints MUST be applied to
"Normalised(CTc)" rather than to "Reserved(CTc)". Thus, when the
optional Local Overbooking method is supported, the Russian Doll
Model definition is extended in the following manner:
o Maximum Number of Bandwidth Constraints (MaxBC)=
Maximum Number of Class-Types (MaxCT) = 8
o for each value of b in the range 0 <= b <= (MaxCT - 1):
SUM (Normalised (CTc)) <= BCb,
for all "c" in the range b <= c <= (MaxCT - 1)
Le Faucheur et. al 7
Russian Dolls model for DS-TE March 2003
A DS-TE LSR implementing RDM and implementing the optional Local
Overbooking method MUST support enforcement of bandwidth constraints
in compliance with this extended definition.
Purely for illustration purposes, the diagram below represents the
Russian Doll Bandwidth Constraints model in a pictorial manner when 3
Class-Types are active and the local overbooking method is used:
I--------------------------------------------------------------I
I-----------------------------------------I Normalised(CT2) I
I--------------------I Normalised(CT2) I + I
I Normalised(CT2) I + I Normalised(CT1) I
I--------------------I Normalised(CT1) I + I
I-----------------------------------------I Normalised(CT0) I
I--------------------------------------------------------------I
I--------BC2--------->
I-------------------------BC1------------->
I-----------------------------------------------BC0------------>
6.2. Example Formulas for Computing "Unreserved TE-Class [i]" With
Local Overbooking
A DS-TE LSR implementing RDM and implementing the optional Local
Overbooking method MUST reflect the RDM bandwidth constraints defined
in section 6.1 above when computing "Unreserved TE-Class [i]".
Again, keeping in mind that details of admission control algorithms
as well as formulas for computing "Unreserved TE-Class [i]" are
outside the scope of the IETF work, we provide in this section, for
illustration purposes, an example of how values for the unreserved
bandwidth for TE-Class[i] might be computed with the Russian Dolls
Model, assuming:
- the basic admission control algorithm which simply deducts
the exact bandwidth of any established LSP from all of the
Bandwidth Constraints relevant to the CT associated with that
LSP.
- the optional per-CT Local Overbooking Multipliers are used.
When the optional local overbooking method is supported, the example
generalized formula of section 5 becomes:
"Unreserved TE-Class [i]" =
LOM(c) x MIN [
[ BCc - SUM ( Normalised(CTb,q) ) ] for q <= p and c <= b <= 7,
. . .
[ BC0 - SUM ( Normalised(CTb,q) ) ] for q <= p and 0 <= b <= 7,
]
Le Faucheur et. al 8
Russian Dolls model for DS-TE March 2003
where:
- TE-Class [i] <--> < CTc , preemption p>
in the configured TE-Class mapping.
6.3. Example Usage of LOM
To illustrate usage of the local overbooking method with the Russian
Dolls model, let's consider a DS-TE deployment where two CTs (CT0 for
data and CT1 for voice) and a single preemption priority are used.
The TE-Class mapping is the following:
TE-Class <--> CT, preemption
==============================
0 CT0, 0
1 CT1, 0
rest unused
Let's assume that on a given link, BCs and LOMs are configured in the
following way:
BC0 = 200
BC1 = 100
LOM(0) = 4 (i.e. = 400%)
LOM(1) = 2 (i.e. = 200%)
Let's further assume that the DS-TE LSR uses the example formulas
presented above for computing unreserved bandwidth values.
If there is no established LSP on the considered link, the LSR will
advertise for that link in IGP :
Unreserved TE-Class [0] = 4 x (200 - 0/4 - 0/2 )= 800
Unreserved TE-Class [1] = 2 x (100- 0/2) = 200
Note again that these values advertised for Unreserved Bandwidth are
larger than BC1 and BC0.
If there is only a single established LSP, with CT=CT0 and BW=100,
the LSR will advertise:
Unreserved TE-Class [0] = 4 x (200 - 100/4 - 0/2 )=700
Unreserved TE-Class [1] = 2 x (100- 0/2) = 200
If there is only a single established LSP, with CT=CT1 and BW=100,
the LSR will advertise:
Unreserved TE-Class [0] = 4 x (200 - 0/4 - 100/2 )= 600
Unreserved TE-Class [1] = 2 x (100- 100/2) = 100
Note that the impact of an LSP on the unreserved bandwidth of a CT
does not depend only on the LOM for that CT: it also depends on the
LOM for the CT of the LSP. This can be seen in our example. A BW=100
tunnel affects Unreserved
CT0 twice as much if it is a CT1 tunnel, than if it is a CT0 tunnel.
It reduces Unreserved CTO by 200 (800->600) rather than by 100
(800->700). This is because LOM(1) is half as big as LOM(0). This
Le Faucheur et. al 9
Russian Dolls model for DS-TE March 2003
illustrates why the local overbooking method allows very fine
accounting of cross-effect of overbooking across CTs, as compared
with the LSP/link size overbooking method.
If there are two established LSPs, one with CT=CT1 and BW=100 and one
with CT=CT0 and BW=100, the LSR will advertise:
Unreserved TE-Class [0] = 4 x (200 - 100/4 - 100/2) = 500
Unreserved TE-Class [1] = 2 x (100 - 100/2) = 100
If there are two LSPs established, one with CT=CT1 and BW=100, and
one with CT=CT0 and BW=480, the LSR will advertise:
Unreserved TE-Class [0] = 4 x (200 - 480/4 - 100/2) = 120
Unreserved TE-Class [1] = 2 x MIN [ (200 - 480/4 - 100/2),
(100 - 100/2) ]
= 2 x MIN [ 30, 50 ]
= 60
7. Security Considerations
Security considerations related to the use of DS-TE are discussed in
[DSTE-PROTO]. Those apply independently of the Bandwidth Constraints
model, including RDM specified in this document.
8. Acknowledgments
We thank Martin Tatham for his earlier contribution in this work.
9. Normative References
[DSTE-REQ] Le Faucheur et al, Requirements for support of Diff-Serv-
aware MPLS Traffic Engineering, draft-ietf-tewg-diff-te-reqts-07.txt,
February 2003.
[DSTE-PROTO] Le Faucheur et al, Protocol extensions for support of
Diff-Serv-aware MPLS Traffic Engineering, draft-ietf-tewg-diff-te-
proto-03.txt, February 2003.
[RFC2119] S. Bradner, Key words for use in RFCs to Indicate
Requirement Levels, RFC2119, March 1997.
10. Informative References
[BC-CONS] Le Faucheur, "Considerations on Bandwidth Constraints Model
for DS-TE", draft-lefaucheur-tewg-russian-dolls-00.txt, June 2002.
[BC-MODEL] Lai, "Bandwidth Constraints Models for DS-TE",
draft-wlai-tewg-bcmodel-00.txt, June 2002.
Le Faucheur et. al 10
Russian Dolls model for DS-TE March 2003
[MAM] Le Faucheur, "Maximum Allocation Bandwidth Constraints Model
for Diff-Serv-aware MPLS Traffic Engineering", draft-lefaucheur-diff-
tet-mam-00.txt, February 2003.
[OSPF-TE] Katz et al., "Traffic Engineering Extensions to OSPF",
draft-katz-yeung-ospf-traffic-09.txt, October 2002.
[ISIS-TE] Smit et al., "IS-IS extensions for Traffic Engineering",
draft-ietf-isis-traffic-04.txt, December 2002.
[RSVP-TE] Awduche et al, "RSVP-TE: Extensions to RSVP for LSP
Tunnels", RFC 3209, December 2001.
[DIFF-MPLS] Le Faucheur et al, "MPLS Support of Diff-Serv", RFC3270,
May 2002.
11. Intellectual Property Considerations
Cisco Systems, Inc. may seek patent or other intellectual property
protection for some of all of the technologies disclosed in this
document. If any standards arising from this document are or become
protected by one or more patents assigned to Cisco Systems, Cisco
Systems intends to disclose those patents and license them on
reasonable and non-discriminatory terms.
12. Editor's Address:
Francois Le Faucheur
Cisco Systems, Inc.
Village d'Entreprise Green Side - Batiment T3
400, Avenue de Roumanille
06410 Biot-Sophia Antipolis
France
Phone: +33 4 97 23 26 19
Email: flefauch@cisco.com
Appendix A - Addressing [DSTE-REQ] Scenarios
This Appendix provides examples of how the Russian Dolls Bandwidth
Constraints model can be used to support each of the scenarios
described in [DSTE-REQ].
1. Scenario 1: Limiting Amount of Voice
By configuring on every link:
- Bandwidth Constraint 1 (for CT1=Voice) = "certain percentage"
of link capacity
- BC0 (for CT1=Voice + CT0= Data) = link capacity
Le Faucheur et. al 11
Russian Dolls model for DS-TE March 2003
By configuring:
- every CT1/Voice TE-LSP with preemption =0
- every CT0/Data TE-LSP with preemption =1
DS-TE with the Russian Dolls Model will address all the requirements:
- amount of Voice traffic limited to desired percentage on
every link
- data traffic capable of using all remaining link capacity
- voice traffic capable of preempting other traffic
2. Scenario 2: Maintain Relative Proportion of Traffic Classes
By configuring on every link:
- BC2 (for CT2) = e.g. 45%
- BC1 (for CT1+CT2) = e.g. 80%
- BC0 (for CT0+CT1+CT2) = e.g.100%
DS-TE with the Russian Dolls Model will ensure that the amount of
traffic of each Class Type established on a link is within acceptable
levels as compared to the resources allocated to the corresponding
Diff-Serv PHBs regardless of which order the LSPs are routed in,
regardless of which preemption priorities are used by which LSPs and
regardless of failure situations. Optional automatic adjustment of
Diff-Serv scheduling configuration could be used for maintaining very
strict relationship between amount of established traffic of each
Class Type and corresponding Diff-Serv resources.
3. Scenario 3: Guaranteed Bandwidth Services
By configuring on every link:
- BC1 (for CT1) = "given" percentage of link bandwidth
(appropriate to achieve the Guaranteed Bandwidth service's
QoS objectives)
- BC0 (for CT0+CT1) = 100% of link bandwidth
DS-TE with the Russian Dolls Model will ensure that the amount of
Guaranteed Bandwidth Traffic established on every link remains below
the given percentage so that it will always meet its QoS objectives.
At the same time it will allow traffic engineering of the rest of the
traffic such that links can be filled up.
Le Faucheur et. al 12
| PAFTECH AB 2003-2026 | 2026-04-22 23:11:42 |