One document matched: draft-ietf-snmpconf-diffpolicy-02.txt
Differences from draft-ietf-snmpconf-diffpolicy-01.txt
Internet Draft DiffServ Policy MIB June 2000
The DiffServ Policy MIB
draft-ietf-snmpconf-diffpolicy-02.txt
Document Revision: 1.4
June 2000
Harrie Hazewinkel
TBD
harrie.hazewinkel@bigfoot.com
David Partain
Ericsson
David.Partain@ericsson.com
Status of this Memo
This document is an Internet-Draft and is in full conformance
with all provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet
Engineering Task Force (IETF), its areas, and its working
groups. Note that other groups may also distribute working
documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other
documents at any time. It is inappropriate to use Internet-
Drafts as reference material or to cite them other than as
"work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed
at http://www.ietf.org/shadow.html.
Copyright Notice
SNMPCONF WG Expires December 2000 [Page 1]
Internet Draft DiffServ Policy MIB June 2000
Copyright (C) The Internet Society (2000). All Rights Reserved.
"Open Issues"
* administrivia: various template things need to be put in
(the internet standard management framework, appropriate
references, security boilerplate, verify intellectual
property clause, the MUST, MAY, SHOULD stuff, etc.) There
are unresolved references.
* Matt White comments: "I think the "What does this MIB do?"
aspect needs to be expanded upon and clarified. Is it an
abstraction of the DiffServ MIB? Is it a DiffServ macro
storage facility? Is it a little of both? DLP: I've put in
a place-holder, but the text is not written.
* We need to include at least one example of usage. This will
be put in after Pittsburgh based upon the presentation that
we do there. After we're sure that our example reflects what
is needed, we'll put it into this MIB.
* to what degree do implementation-specific modules convey
information about state or utilization and how do we get
that information, and how is it shown in the policy system.
* for each domain, we may need to understand capacity and
utilization. If so, we need to have appropriate MIB
objects that allow you to get this.
1. Abstract
The MIB Module described in this document provides a
conceptual layer between high-level "network-wide" policy
definitions that affect configuration of the differentiated
services (DiffServ) subsystem and the instance-specific
information that would include such details as the parameters
for all the queues associated with each interface in a system.
This essentially provides an interface for configuring
DiffServ at a conceptually higher layer than that of the
DiffServ Architecture MIB [DIFFSERVMIB].
This version of this memo is aligned with the DIFF-SERV-MIB
[DIFFSERVMIB] found in draft-ietf-diffserv-mib-03.txt. This
MIB module will be aligned with that work as updates are made.
SNMPCONF WG Expires December 2000 [Page 2]
Internet Draft DiffServ Policy MIB June 2000
2. The SNMP Management Framework
The SNMP Management Framework presently consists of five major
components:
o An overall architecture, described in RFC 2571 [1].
o Mechanisms for describing and naming objects and events
for the purpose of management. The first version of this
Structure of Management Information (SMI) is called SMIv1
and described in RFC 1155 [2], RFC 1212 [3] and RFC 1215
[4]. The second version, called SMIv2, is described in
RFC 2578 [5], RFC 2579 [6] and RFC 2580 [7].
o Message protocols for transferring management
information. The first version of the SNMP message
protocol is called SNMPv1 and described in RFC 1157
[8]. A second version of the SNMP message protocol,
which is not an Internet standards track protocol, is
called SNMPv2c and described in RFC 1901 [9] and RFC
1906 [10]. The third version of the message protocol is
called SNMPv3 and described in RFC 1906 [10], RFC 2572
[11] and RFC 2574 [12].
o Protocol operations for accessing management
information. The first set of protocol operations and
associated PDU formats is described in RFC 1157 [8]. A
second set of protocol operations and associated PDU
formats is described in RFC 1905 [13].
o A set of fundamental applications described in RFC 2573 [14]
and the view-based access control mechanism described
in RFC 2575 [15].
A more detailed introduction to the current SNMP Management
Framework can be found in RFC 2570 [16].
Managed objects are accessed via a virtual information store,
termed the Management Information Base or MIB. Objects in the
MIB are defined using the mechanisms defined in the SMI.
This memo specifies a MIB module that is compliant to the
SMIv2. A MIB conforming to the SMIv1 can be produced through
the appropriate translations. The resulting translated MIB
must be semantically equivalent, except where objects or
SNMPCONF WG Expires December 2000 [Page 3]
Internet Draft DiffServ Policy MIB June 2000
events are omitted because no translation is possible (use of
Counter64). Some machine-readable information in SMIv2 will be
converted into textual descriptions in SMIv1 during the
translation process. However, this loss of machine readable
information is not considered to change the semantics of the
MIB.
3. Introduction
This memo defines a MIB module which can be used to convey
information about desired network-wide DiffServ-based policy
behavior. This module is designed to integrate with the
Policy-based Management MIB module [POLICYMIB] as well as the
DiffServ Architecture MIB module [DIFFSERVMIB] published by
the DiffServ working group. Together these three documents
represent an instance of an integrated architecture for both
device-specific and network-wide policy management which is
fully integrated with the Internet Standard Management
Framework.
This is the first of what is expected to be a wide number of
other network-wide policy modules to be developed in the
future in a wide range of areas.
Within the DiffServ architecture a MIB module is already
defined [DIFFSERVMIB] that operates on a device level. The
MIB module in this memo (the DIFFSERV-POLICY-MIB) creates a
coherent policy configuration management view (domain-
specific) as an umbrella over this mechanism-specific MIB.
That is, DIFFSERV-POLICY-MIB provides a conceptual API for
configuration of DiffServ parameters in a device at a higher
level than the DiffServ Architecture MIB [DIFFSERVMIB].
4. Definitions
Terminology used in discussing policy-based configuration
management have been the source of much discussion and
confusion. [PBCM] provides a discussion of the terms used in
discussing this topic.
Note that this is simply a template which needs to be altered
to fit into the documents better.
SNMPCONF WG Expires December 2000 [Page 4]
Internet Draft DiffServ Policy MIB June 2000
"Much of the information in this section is an adaptation and
expansion of a presentations given at the 47th IETF in during
the Policy Framework Working Group session. By adopting terms
used by the Policy Framework Working Group wherever feasible;
the SNMP Configuration Working Group hopes to reduce the
terminology confusion that has existed in this area. Work is
ongoing in the SNMP Configuration and Policy Framework groups
as well as others; so some change is inevitable. Here are
terms that are used to describe policy information at
different levels of abstraction moving from the most general
to the most specific.
1. Domain Specific.
A domain is a general area of technology such as service
quality or security. Services, or service level agreements,
may span several domains, each of them potentially
including many policies. As a general rule, people will
not discuss these domains in the abstract. They will most
often be discussed with technology or application-specific
examples. Examples of technical domains include IPSec
and Differentiated Services. When expressed in terms
specific to a particular domain, a policy is said to be
at the Domain Specific level of detail.
There is little in common between how one would configure
differentiated services with how one would configure IPsec
[IPSEC]. They may both be required for a particular service
agreement however. For example, people who want to use
a voice over IP application might also want to ensure a
certain level of security for these communications.
2. Mechanism Specific
Mechanisms are technologies used within a particular
domain. For example, in the differentiated services domain,
RED or WRED (Weighted Random Early Detection) might be
used as one of the mechanisms that devices employ to
support differentiated services and the applications
on which they rely. Policy descriptions that include
the details associated with a particular mechanism,
are said to be mechanism specific.
3. Implementation Specific
SNMPCONF WG Expires December 2000 [Page 5]
Internet Draft DiffServ Policy MIB June 2000
Implementation specific details are those parameters
that a particular vendor might use in an implementation
that augment a standard set of mechanism-specific
parameters. Vendors often add special capabilities to
basic mechanisms as a way of meeting special customer
requirements or differentiating themselves from their
competitors. These special capabilities are often a result
of the implementation approach that a vendor has used for
the product, thus the term, Implementation Specific. For
example, if a router vendor implemented a particular
routing protocol, they would have the mechanism specific
parameters that control the behavior of that software. The
vendor might have chosen to run several instances of
that routing protocol, perhaps on different processors,
for performance reasons. The parameters that are used
to control the distribution of work on the different
processors for that protocol would be implementation
specific.
4. Instance Specific
Network operators are most familiar and comfortable with
information of this type. Instance specific information
is information refers to parameter values that have
been associated with a specific instance in a managed
element. For example, The Border Gateway Protocol is a
routing protocol that has a number of parameters that
describe information about a particular router's view
of other routers that it is sharing information with,
peer routers. One such parameter defined in the BGP
MIB Module [BGP MIB] is the desired connection retry
interval for a peer, bgpPeerConnectRetryInterval. An
example value would be 120 (seconds). When expressed
with this level of specificity, one would say that this
is mechanism specific data. If we were to see a value of
bgpPeerConnectRetryInterval. 10.0.0.1 = 120 we would be
looking at the retry interval of the peer router found
at IP address 10.0.0.1. The value for this instance is
120 seconds, instance specific data.
One of the goals of policy-based (configuration)
management is to improve the efficiency of configuration
operations. This is accomplished in part by eliminating the
necessity of sending to the managed device a configuration
object for every instance of that object in a system. For
SNMPCONF WG Expires December 2000 [Page 6]
Internet Draft DiffServ Policy MIB June 2000
example, if we wanted to change one of the BGP parameters
referenced above on a large system for each interface
that is supporting the BGP, there may be many individual
commands needed to accomplish this task. If a command
line interface were used as the primary configuration
tool in this example, many configuration commands would
be needed as well.
When we say that a a policy is at the instance independent
level of abstraction, we mean that the value for a
particular parameter is independent of the instances to
which it will be applied."
5. What this MIB Module Provides
To be written: to provide a high-level description of what
this MIB does.
6. Relationship to other MIBs
In this section we describe the relationship of this MIB
module to other MIB modules. The overall architecture used
for policy configuration management is described in
[POLICYMIB].
6.1. The Policy-based Management MIB module
[POLICYMIB] defines a MIB module that enables policy-based
configuration management of infrastructure using the Internet
Standard Management Framework. The document includes a table
for configuring policies to be implemented, tables for storing
the roles of elements on a particular device, a table for
representing the capabilities of a device with respect to
policy management, a table for referencing elements affected
by a policy, and a table which points to into the mechanism-
specific MIB (this memo). This last table of pointers enables
management applications to determine the mechanism-specific
configuration to which a particular policy applies. The
primary purpose of this is to enable the manager to correct
errors in installed policies.
The pmPolicyMechanismTable (as the table in [POLICYMIB] is
SNMPCONF WG Expires December 2000 [Page 7]
Internet Draft DiffServ Policy MIB June 2000
tentatively called), points into mechanism-specific MIBs and
includes a RowPointer object pointing into a row in the
diffPolicyPHBTable defined below.
See [POLICYMIB] for a full description of the policy-based
configuration framework it provides.
6.2. The DiffServ MIB module
The DiffServ Architecture MIB module [DIFFSERVMIB] provides a
common set of managed objects useful for configuring DiffServ
parameters on a particular device. This is what is refered to
as instance-level configuration. It is the alteration of the
instance-level information in that MIB module which MAY be
done via the objects provided by the DiffServ Policy MIB
module defined in this memo.
It is recognized that vendors may include additional managed
objects in their devices (via vendor-specific MIB modules) for
configuring DiffServ parameters. If a vendor chooses to use
the objects defined in this memo for configuration, the vendor
should also provide additional managed objects in a similar
approach as defined for the DiffServ Architecture MIB module
and the DiffServ Policy MIB module.
The remainder of this subsection describes the relationship of
each table in the DiffServ Architecture MIB module to this MIB
module.
- diffServClassifierTable: instantiates the traffic
classification data path. Whenever a configuration in the
DiffServ Policy MIB module is made active, a new entry in
the diffServClassifierTable will be created
with data path configuration as defined in the
diffPolicyPerHopBehaviorTable.
- diffServSixTupleClfrTable: traffic identification table
and does not have a direct influence on the per-hop-behavior.
Entries identifying traffic can be used directly by the
subsystem implementing the DiffServ Policy MIB module.
SNMPCONF WG Expires December 2000 [Page 8]
Internet Draft DiffServ Policy MIB June 2000
- diffServMeterTable is a possible target table for the
diffPolicyMeterTable.
- diffServTBMeterTable is also a target table for the
diffPolicyMeterTable. When per-hop-behavior configurations
are made active, the meter configuration used will be
instantiated in the diffServTBMeterTable
- diffServActionTable instantiates actions that can be
performed on a stream of traffic. This table is the target
for the diffPolicyActionTable whenever a configuration is
made active.
- diffServDscpMarkActTable is a configuration table for traffic
marking. It is possible to have mark actions defined in this
table that are not used for the traffic. For this reason
the manager can use this table directly in conjunction with
the DiffServ Policy MIB module.
- diffServAlgDropTable is a configuration table for dropping
traffic. It is possible to have mark actions defined in this
table that are not used for the traffic. For this reason
the manager can use this table directly in conjunction with
the DiffServ Policy MIB module.
The following tables are not used for configuration and are
not referenced in any way:
- diffServCountActTable
- diffServCountActXTable
- diffServDropActXTable
- diffServQMeasureTable
The Differentiated Services Policy MIB module was designed to
have configuration templates for the Differentiated Services
MIB module. Therefore, it may appear that the Differentiated
Services Policy MIB is largely a copy of the DIFF-SERV-MIB.
However, there is a significant difference in the semantics of
the managed objects.
In the DIFF-SERV-MIB [DIFFSERVMIB], meters, actions, queues
and schedulers are directly related to interfaces and their
interface direction. The objects directly influence traffic
SNMPCONF WG Expires December 2000 [Page 9]
Internet Draft DiffServ Policy MIB June 2000
behavior. This is in contrast to the objects in the
Differentiated Services Policy MIB module, where only
configuration templates are defined. The values of a template
are only to be applied when a per-hop-behavior is activated
via a policy. Only in that case are the values connected to an
interface and its direction, which could be seen as being
7. MIB Module Design
In this section the overall design of the DiffServ Policy MIB
module is described. The first part will describe how this
module is positioned within the overall architecture.
The DiffServ Policy MIB module of the SNMP-based configuration
management framework is positioned between the Policy-based
Management MIB module and the instance-specific MIB module
(the DiffServ Architecture MIB module) as described above.
The following scheme of actions MAY be used for the subsystem:
1) The instance-specific MIB module (for this document the
DiffServ Architecture MIB module) is assumed to be
implemented on the device already.
2) The Policy-based Management MIB module includes the filters
and actions and is implemented on the device.
3) The mechanism-specific policy MIB module (in this case
the DiffServ Policy MIB module) registers its capability
in the capability table of the Policy-based Management MIB
module.
4) If a device has knowledge of default configurations, it can
create the required managed objects for the default
configurations in the tables of the mechanism-specific
policy MIB module.
5) The manager can then read the capability table after which
it knows about the capabilities and can start configuring
the mechanism-specific policy MIB module and the various
roles that may exist (this defines the configurations and
associations as necessary)
SNMPCONF WG Expires December 2000 [Page 10]
Internet Draft DiffServ Policy MIB June 2000
6) The manager can then map/instantiate policies as required
via the policy table.
The MIB module is designed with the following tables:
- A per-hop-behavior table (diffPolicyPHBTable)
- A meter table (diffPolicyMeterTable)
- An action table (diffPolicyActionTable)
- A queue table (diffPolicyQTable)
- A scheduler table (diffPolicySchedulerTable)
Unlike most MIB modules, changes on the managed objects in
this MIB module do not cause a change in the device. This MIB
module is used to set up per-hop-behavior configurations. As
soon as configurations are made active via the POLICY-
MANAGEMENT-MIB, the configurations defined within this MIB
module will be instantiated on the instance specific MIB, the
DIFF-SERV-MIB.
Note that this is a conceptual process. That is, the
configuration may not actually go through an API available in
the subsystem which implements the DIFF-SERV-MIB module.
However, configuration via the DiffServ Policy MIB module will
alter the same instrumentation as the DIFF-SERV-MIB module
whether it does it via the DIFF-SERV-MIB module or not.
The tables in the MIB module are:
- The diffPolicyPHBTable provides managed objects for
per-hop-behavior configuration. This table contains
RowPointers into subsequent tables in such a way that the
Traffic Control Block (TCB) can be created as soon as a
configuration is made active.
- The diffPolicyMeterTable provides the managed objects for the
meters used in the per-hop-behavior configuration.
This table also contains RowPointers into next data-path
elements if the traffic conforms to the meter or not.
- The diffPolicyActionTable provides managed objects for
configuring actions that are connected with meters.
Via this table, and using 'diffPolicyMeterFailNext' and/or
'diffPolicyMeterSucceedNext', the specific action can
be configured.
SNMPCONF WG Expires December 2000 [Page 11]
Internet Draft DiffServ Policy MIB June 2000
- The diffPolicyQTable provides managed objects for setting up
individual queue configurations. The individual queues can
be configured with the sample interval and the weight of
the queue.
- The diffPolicySchedulerTable enumerates policy configuration
templates for packet schedulers.
8. Managed objects definitions (MIB module)
-- This version of the MIB is aligned with the DIFF-SERV-MIB
-- found in draft-ietf-diffserv-mib-03.txt. This MIB module will
-- be aligned with that work as updates are made.
DIFFSERV-POLICY-MIB DEFINITIONS ::= BEGIN
IMPORTS
Unsigned32, Integer32, OBJECT-TYPE, MODULE-IDENTITY, zeroDotZero, mib-2
FROM SNMPv2-SMI
RowStatus, RowPointer, TestAndIncr, DateAndTime
FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB;
diffPolicyMib MODULE-IDENTITY
LAST-UPDATED "200006301100Z" -- June 30, 2000, 13:00 Italy
ORGANIZATION "SNMPCONF WG"
CONTACT-INFO
"SNMPCONF Working Group
http://www.ietf.org/html.charters/snmpconf-charter.html
Editors:
Harrie Hazewinkel
Postal: Titanstraat 2
9933 CE Delfzijl
The Netherlands
Tel: +31 596 615843 or +39 331974135
FAX: +39 0331974135
SNMPCONF WG Expires December 2000 [Page 12]
Internet Draft DiffServ Policy MIB June 2000
E-mail: harrie.hazewinkel@bigfoot.com
David Partain
Postal: Ericsson Radio Systems
P.O. Box 1248
SE-581 12 Linkoping
Sweden
Tel: +46 13 28 41 44
E-mail: David.Partain@ericsson.com"
DESCRIPTION
"This MIB module contains differentiated services
specific managed objects to perform policy-based
configuration management. This MIB defines
'templates' to be used to instantiate
per-hop-behaviors to be assigned when a policy is
created and activated."
::= { mib-2 22222222 } -- Needs to be assigned by IANA
diffPolicyMIBObjects OBJECT IDENTIFIER ::= { diffPolicyMib 1 }
diffPolicyMIBConformance OBJECT IDENTIFIER ::= { diffPolicyMib 3 }
--
-- The per-hop-behavior
--
-- Issues:
-- Do we want a spin-lock on this whole table or on each row
-- of the table, or not at all?
diffPolicyPHBUnique OBJECT-TYPE
SYNTAX TestAndIncr
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The diffPolicyPHBUnique object yields a unique new
value for diffPolicyPHBId when read and subsequently
set. This value must be tested for uniqueness."
::= { diffPolicyMIBObjects 1 }
diffPolicyPHBTable OBJECT-TYPE
SYNTAX SEQUENCE OF DiffPolicyPHBEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
SNMPCONF WG Expires December 2000 [Page 13]
Internet Draft DiffServ Policy MIB June 2000
"A table which defines the various per-hop-behaviors
for which the system has default 'templates'."
::= { diffPolicyMIBObjects 2 }
diffPolicyPHBEntry OBJECT-TYPE
SYNTAX DiffPolicyPHBEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry defining a per-hop-behavior.
Each entry in this table combines the various
parameters (entries) into a specific per-hop-behavior.
Entries in this table can as well being defined by
a vendor (preconfigured) or as well being defined
by a management application."
INDEX { diffPolicyPHBId }
::= { diffPolicyPHBTable 1 }
DiffPolicyPHBEntry ::= SEQUENCE {
diffPolicyPHBId Integer32,
diffPolicyPHBDescr SnmpAdminString,
diffPolicyPHBOwner SnmpAdminString,
diffPolicyPHBLastChange DateAndTime,
diffPolicyPHBTrafficID RowPointer,
diffPolicyPHBClassPrecedence Unsigned32,
diffPolicyPHBMeter RowPointer,
diffPolicyPHBAction RowPointer,
diffPolicyPHBQueue RowPointer,
diffPolicyPHBScheduler RowPointer,
diffPolicyPHBStatus RowStatus
}
diffPolicyPHBId OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique id for the per-hop-behavior policy."
::= { diffPolicyPHBEntry 1 }
diffPolicyPHBDescr OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
SNMPCONF WG Expires December 2000 [Page 14]
Internet Draft DiffServ Policy MIB June 2000
"A human-readable description to identify this
defined per-hop-behavior.
Note that this is an SnmpAdminString, which
permits UTF-8 strings."
::= { diffPolicyPHBEntry 2 }
diffPolicyPHBOwner OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The owner who creates this entry."
::= { diffPolicyPHBEntry 3 }
diffPolicyPHBLastChange OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The date and time when this entry was changed for
the last time."
::= { diffPolicyPHBEntry 4 }
diffPolicyPHBTrafficID OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The pointer to traffic identification used for this
per-hop-behavior definition.
This value points to a traffic classifying entry in
the 'diffServClassifierTable' or
the 'diffServSixTupleClfrTable'.
NOTE: The traffic classifying tables of the DIFF-SERV-MIB
can be used for policy configuration in this MIB module
because the entries in the tables 'diffServClassifierTable' or
the 'diffServSixTupleClfrTable' configure traffic filter
templates."
::= { diffPolicyPHBEntry 5 }
diffPolicyPHBClassPrecedence OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
SNMPCONF WG Expires December 2000 [Page 15]
Internet Draft DiffServ Policy MIB June 2000
DESCRIPTION
"The precedence of the classifier for this
per-hop-behavior definition."
::= { diffPolicyPHBEntry 6 }
diffPolicyPHBMeter OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The meter which is next in the data path for the
defined classifier applicable to this per-hop-behavior
configuration.
The value points to an entry in the 'diffPolicyMeterTable'."
DEFVAL { zeroDotZero }
::= { diffPolicyPHBEntry 7 }
diffPolicyPHBAction OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The action which is next in the data path for the
defined classifier applicable to this per-hop-behavior
definition.
The value points to an entry in the 'diffPolicyActionTable'.
The value 'zeroDotZero' is used when there is no
action associated with the per-hop-behavior."
DEFVAL { zeroDotZero }
::= { diffPolicyPHBEntry 8 }
diffPolicyPHBQueue OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The queue defined that is used for the
configuration of this per-hop-behavior.
The value points to an entry in the 'diffPolicyQTable'.
The value 'zeroDotZero' is used when there is no
SNMPCONF WG Expires December 2000 [Page 16]
Internet Draft DiffServ Policy MIB June 2000
queue associated with the per-hop-behavior."
DEFVAL { zeroDotZero }
::= { diffPolicyPHBEntry 9 }
diffPolicyPHBScheduler OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Scheduler defined that is used for the
configuration of this per-hop-behavior.
The value points to an entry in the 'diffPolicySchedulerTable'.
The value 'zeroDotZero' is used when there is no
scheduler associated with the per-hop-behavior"
DEFVAL { zeroDotZero }
::= { diffPolicyPHBEntry 10 }
diffPolicyPHBStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"RowStatus object used for creation and deletion of
rows in this table."
::= { diffPolicyPHBEntry 11 }
--
-- Meters Configuration
--
diffPolicyMeterUnique OBJECT-TYPE
SYNTAX TestAndIncr
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The diffPolicyMeterUnique object yields a unique new
value for diffPolicyMeterId when read and subsequently
set. This value must be tested for uniqueness."
::= { diffPolicyMIBObjects 3 }
diffPolicyMeterTable OBJECT-TYPE
SYNTAX SEQUENCE OF DiffPolicyMeterEntry
SNMPCONF WG Expires December 2000 [Page 17]
Internet Draft DiffServ Policy MIB June 2000
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table enumerates templates for configuration of
specific token bucket meters that can be used for
per-hop-behavior definitions.
This tables provides policy configuration templates
for the 'diffServMeterTable' and the 'diffServTBMeterTable'.
When changes are made in this table the behavior of the
DiffServ router is not changed. The behavior only changes
when the policy of which this meter is part is applied."
::= { diffPolicyMIBObjects 4 }
diffPolicyMeterEntry OBJECT-TYPE
SYNTAX DiffPolicyMeterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the meter table."
INDEX { diffPolicyMeterId }
::= { diffPolicyMeterTable 1 }
DiffPolicyMeterEntry ::= SEQUENCE {
diffPolicyMeterId Integer32,
diffPolicyMeterRate Unsigned32,
diffPolicyMeterBurstSize Unsigned32,
diffPolicyMeterFailNext RowPointer,
diffPolicyMeterSucceedNext RowPointer,
diffPolicyMeterStatus RowStatus
}
diffPolicyMeterId OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index to make MeterId for each entry."
::= { diffPolicyMeterEntry 1 }
diffPolicyMeterRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "KBPS" -- kilobits
SNMPCONF WG Expires December 2000 [Page 18]
Internet Draft DiffServ Policy MIB June 2000
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The token bucket rate, in kilo-bits per second (KBPS)
applicable for this Meter definition."
::= { diffPolicyMeterEntry 2 }
diffPolicyMeterBurstSize OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bytes"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The configuration value of the number of bytes
in a single transmission burst when this policy
configuration is applied to a Meter."
::= { diffPolicyMeterEntry 3 }
diffPolicyMeterFailNext OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The next Meter or Action configured that will handle the traffic
when the meter does not conform the meter.
This value points can point towards an entry in the
diffPolicyMeterTable, diffPolicyActionTable.
The value 'zeroDotZero' is used when there is no
next component in the data path."
DEFVAL { zeroDotZero }
::= { diffPolicyMeterEntry 4 }
diffPolicyMeterSucceedNext OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The next Meter or Action configured that will handle the traffic
when the meter does conform the meter.
This value points can point towards an entry in the
diffPolicyMeterTable, diffPolicyActionTable.
The value 'zeroDotZero' is used when there is no
SNMPCONF WG Expires December 2000 [Page 19]
Internet Draft DiffServ Policy MIB June 2000
next component in the data path."
DEFVAL { zeroDotZero }
::= { diffPolicyMeterEntry 5 }
diffPolicyMeterStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The RowStatus variable controls the creation
or deletion of a meter configuration."
::= { diffPolicyMeterEntry 6 }
--
-- Actions
--
diffPolicyActionUnique OBJECT-TYPE
SYNTAX TestAndIncr
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The diffPolicyActionUnique object yields a unique new
value for diffPolicyActionId when read and subsequently
set. This value must be tested for uniqueness."
::= { diffPolicyMIBObjects 5 }
diffPolicyActionTable OBJECT-TYPE
SYNTAX SEQUENCE OF DiffPolicyActionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This Table enumerates templates for actions that can be
performed on a stream of traffic. Various templates
can be concatenated.
This table can be used for configuration of the
'diffServActionTable' and 'diffServDscpMarkActTable'.
For policy configuration for these 2 tables they
are combined in 1 table."
::= { diffPolicyMIBObjects 6 }
diffPolicyActionEntry OBJECT-TYPE
SYNTAX DiffPolicyActionEntry
MAX-ACCESS not-accessible
SNMPCONF WG Expires December 2000 [Page 20]
Internet Draft DiffServ Policy MIB June 2000
STATUS current
DESCRIPTION
"An entry in the action table describes the actions
applied to traffic exiting a given meter."
INDEX { diffPolicyActionId }
::= { diffPolicyActionTable 1 }
DiffPolicyActionEntry ::= SEQUENCE {
diffPolicyActionId Unsigned32,
diffPolicyActionNext RowPointer,
diffPolicyActionType INTEGER,
diffPolicyActionStatus RowStatus
}
diffPolicyActionId OBJECT-TYPE
SYNTAX Unsigned32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Action Id enumerates the Action entry for
a per-hop-behavior definition."
::= { diffPolicyActionEntry 1 }
diffPolicyActionNext OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Next pointer indicates the next data path element
to handle the traffic that is applicable to this
per-hop-behavior definition.
The value 'zeroDotZero' is used when there is no
next component in the data path."
DEFVAL { zeroDotZero }
::= { diffPolicyActionEntry 2 }
diffPolicyActionType OBJECT-TYPE
SYNTAX INTEGER {
other(1), -- types not specified here.
mark(2), -- mark or remark
count(3), -- count
alwaysDrop(4), -- disallow traffic
tailDrop(5), -- fix queue size Drop
randomDrop(6), -- Random Drop
SNMPCONF WG Expires December 2000 [Page 21]
Internet Draft DiffServ Policy MIB June 2000
deterDrop(7) -- Deterministic Drop
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates the type of action for this configuration."
::= { diffPolicyActionEntry 3 }
diffPolicyActionStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The RowStatus variable controls the creation,
or deletion of a action configuration."
::= { diffPolicyActionEntry 4 }
--
-- Queues
--
diffPolicyQUnique OBJECT-TYPE
SYNTAX TestAndIncr
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The diffPolicyQUnique object yields a unique new value
for diffPolicyQId when read and subsequently set. This
value must be tested for uniqueness."
::= { diffPolicyMIBObjects 7 }
diffPolicyQTable OBJECT-TYPE
SYNTAX SEQUENCE OF DiffPolicyQEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Queue Table enumerates the queues that
can be assigned when a per-hop-behavior is assigned.
This table includes the measure values which
are defined in the DIFF-SERV-MIB in a separate table."
::= { diffPolicyMIBObjects 8 }
diffPolicyQEntry OBJECT-TYPE
SYNTAX DiffPolicyQEntry
MAX-ACCESS not-accessible
SNMPCONF WG Expires December 2000 [Page 22]
Internet Draft DiffServ Policy MIB June 2000
STATUS current
DESCRIPTION
"An entry in the Queue Table describes a single FIFO
queue."
INDEX { diffPolicyQId, diffPolicyQId }
::= { diffPolicyQTable 1 }
DiffPolicyQEntry ::= SEQUENCE {
diffPolicyQId Integer32,
diffPolicyQPriority Unsigned32,
diffPolicyQMinRateAbs Unsigned32,
diffPolicyQMinRateRel Unsigned32,
diffPolicyQMaxRateAbs Unsigned32,
diffPolicyQMaxRateRel Unsigned32,
diffPolicyQStatus RowStatus
}
diffPolicyQId OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Queue Id enumerates the Queue entry."
::= { diffPolicyQEntry 1 }
diffPolicyQPriority OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The priority of the queue."
::= { diffPolicyQEntry 2 }
diffPolicyQMinRateAbs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kilobits per second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The minimum absolute rate, in kilobits/sec, with which
a downstream scheduler element should configured."
REFERENCE
"diffServQMinRateAbs from [DIFFSERVMIB]"
::= { diffPolicyQEntry 3 }
SNMPCONF WG Expires December 2000 [Page 23]
Internet Draft DiffServ Policy MIB June 2000
diffPolicyQMinRateRel OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The minimum rate with which a downstream scheduler element
should be configured."
REFERENCE
"diffServQMinRateRel from [DIFFSERVMIB]"
::= { diffPolicyQEntry 4 }
diffPolicyQMaxRateAbs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kilobits per second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum absolute rate, in kilobits/sec, with which
a downstream scheduler element should configured."
REFERENCE
"diffServQMaxRateAbs from [DIFFSERVMIB]"
::= { diffPolicyQEntry 5 }
diffPolicyQMaxRateRel OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum rate with which a downstream scheduler element
should be configured."
REFERENCE
"diffServQMaxRateRel from [DIFFSERVMIB]"
::= { diffPolicyQEntry 6 }
diffPolicyQStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The RowStatus variable controls the creation,
or deletion of a queue configuration."
::= { diffPolicyQEntry 7 }
--
-- Scheduler
SNMPCONF WG Expires December 2000 [Page 24]
Internet Draft DiffServ Policy MIB June 2000
--
diffPolicySchedulerUnique OBJECT-TYPE
SYNTAX TestAndIncr
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The diffPolicySchedulerUnique object yields a unique new value for
diffPolicySchedulerId when read and subsequently set. This value
must be tested for uniqueness and can be used by a configuring
system to obtain a unique value for diffPolicySchedulerId for
purposes of row creation in the diffPolicySchedulerTable."
::= { diffPolicyMIBObjects 9 }
diffPolicySchedulerTable OBJECT-TYPE
SYNTAX SEQUENCE OF DiffPolicySchedulerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Scheduler Table enumerates policy configuration
templates for packet schedulers."
::= { diffPolicyMIBObjects 10 }
diffPolicySchedulerEntry OBJECT-TYPE
SYNTAX DiffPolicySchedulerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the Policy Scheduler Table describing a
single configuration template for a scheduling algorithm."
INDEX { diffPolicySchedulerId }
::= { diffPolicySchedulerTable 1 }
DiffPolicySchedulerEntry ::= SEQUENCE {
diffPolicySchedulerId Integer32,
diffPolicySchedulerMethod INTEGER,
diffPolicySchedulerNext RowPointer,
diffPolicySchedulerStatus RowStatus
}
diffPolicySchedulerId OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS not-accessible
STATUS current
SNMPCONF WG Expires December 2000 [Page 25]
Internet Draft DiffServ Policy MIB June 2000
DESCRIPTION
"The Policy Scheduler Id enumerates the Policy Scheduler entry."
::= { diffPolicySchedulerEntry 1 }
diffPolicySchedulerMethod OBJECT-TYPE
SYNTAX INTEGER {
other(1), -- not listed here
priorityq(2), -- Priority Queueing
wrr(3) -- Weighed Round Robin
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The scheduling algorithm used when this policy is applied
to a Scheduler."
REFERENCE
"diffServSchedulerMethod [DIFFSERV-MIB]"
::= { diffPolicySchedulerEntry 2 }
diffPolicySchedulerNext OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The next data path component that is applicable for
this scheduler configuration.
The value can point to an entry in the 'diffPolicyMeterTable',
'diffPolicyActionTable', 'diffPolicyQTable' or the
'diffPolicySchedulerTable'.
The value 'zeroDotZero' is used when there is no
next component in the data path."
DEFVAL { zeroDotZero }
::= { diffPolicySchedulerEntry 3 }
diffPolicySchedulerStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The RowStatus variable via which this configuration
template can be created, deleted or modified."
::= { diffPolicySchedulerEntry 4 }
SNMPCONF WG Expires December 2000 [Page 26]
Internet Draft DiffServ Policy MIB June 2000
--
-- MIB Compliance statements.
--
diffPolicyMIBCompliances OBJECT IDENTIFIER ::= { diffPolicyMIBConformance 1 }
diffPolicyMIBGroups OBJECT IDENTIFIER ::= { diffPolicyMIBConformance 2 }
diffPolicyMIBFullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The full compliance for this MIB module."
MODULE -- This module
MANDATORY-GROUPS { diffPolicyMIBPerHopBehaviorGroup,
diffPolicyMIBMeterGroup,
diffPolicyMIBActionGroup,
diffPolicyMIBQueueGroup,
diffPolicyMIBSchedulerGroup }
::= { diffPolicyMIBCompliances 1 }
diffPolicyMIBPerHopBehaviorGroup OBJECT-GROUP
OBJECTS { diffPolicyPHBDescr,
diffPolicyPHBOwner,
diffPolicyPHBLastChange,
diffPolicyPHBTrafficID,
diffPolicyPHBClassPrecedence,
diffPolicyPHBMeter,
diffPolicyPHBAction,
diffPolicyPHBQueue,
diffPolicyPHBScheduler,
diffPolicyPHBStatus
}
STATUS current
DESCRIPTION
"The per-hop-behavior Group defines the MIB Objects that
describe the configuration template for the per-hop-behavior."
::= { diffPolicyMIBGroups 1 }
diffPolicyMIBMeterGroup OBJECT-GROUP
OBJECTS { diffPolicyMeterRate,
diffPolicyMeterBurstSize,
diffPolicyMeterFailNext,
diffPolicyMeterSucceedNext,
diffPolicyMeterStatus
}
STATUS current
SNMPCONF WG Expires December 2000 [Page 27]
Internet Draft DiffServ Policy MIB June 2000
DESCRIPTION
"The Meter Group defines the objects used for configuring a generic
meter and token bucket elements."
::= { diffPolicyMIBGroups 2 }
diffPolicyMIBActionGroup OBJECT-GROUP
OBJECTS { diffPolicyActionNext,
diffPolicyActionType,
diffPolicyActionStatus
}
STATUS current
DESCRIPTION
"The Action Group defines the objects used for configuration of
actions."
::= { diffPolicyMIBGroups 3 }
diffPolicyMIBQueueGroup OBJECT-GROUP
OBJECTS { diffPolicyQPriority,
diffPolicyQMinRateAbs,
diffPolicyQMinRateRel,
diffPolicyQMaxRateAbs,
diffPolicyQMaxRateRel,
diffPolicyQStatus
}
STATUS current
DESCRIPTION
"The Queue Group contains the objects which can
be used for configuration of Queues."
::= { diffPolicyMIBGroups 4 }
diffPolicyMIBSchedulerGroup OBJECT-GROUP
OBJECTS { diffPolicySchedulerMethod,
diffPolicySchedulerNext,
diffPolicySchedulerStatus
}
STATUS current
DESCRIPTION
"The Scheduler Group contains the objects that are used
for configuration of packet schedulers on interfaces."
::= { diffPolicyMIBGroups 5 }
END
SNMPCONF WG Expires December 2000 [Page 28]
Internet Draft DiffServ Policy MIB June 2000
9. Security Considerations
Security information here
10. Editors' Addresses
Harrie Hazewinkel
Titanstraat 2
9933 CE Delfzijl
The Netherlands
Phone: +31 596 615843 or +39 331974135
EMail: harrie.hazewinkel@bigfoot.com
David Partain
Ericsson Radio Systems
Research and Innovation
P.O. Box 1248
SE-581 12 Linkoping
Sweden
Phone: +46 13 28 41 44
EMail: David.Partain@ericsson.com
11. Full Copyright Statement
Copyright (C) The Internet Society (2000). All Rights
Reserved.
This document and translations of it may be copied and
furnished to others, and derivative works that comment on or
otherwise explain it or assist in its implementation may be
prepared, copied, published and distributed, in whole or in
part, without restriction of any kind, provided that the above
copyright notice and this paragraph are included on all such
copies and derivative works. However, this document itself
may not be modified in any way, such as by removing the
copyright notice or references to the Internet Society or
other Internet organizations, except as needed for the purpose
of developing Internet standards in which case the procedures
for copyrights defined in the Internet Standards process must
be followed, or as required to translate it into languages
other than English.
The limited permissions granted above are perpetual and will
SNMPCONF WG Expires December 2000 [Page 29]
Internet Draft DiffServ Policy MIB June 2000
not be revoked by the Internet Society or its successors or
assigns.
This document and the information contained herein is provided
on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE
USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR
ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE."
12. References
Others to be added as time goes by!
[1] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for
Describing SNMP Management Frameworks", RFC 2571, Cabletron
Systems, Inc., BMC Software, Inc., IBM T. J. Watson Research, April
1999
[2] Rose, M., and K. McCloghrie, "Structure and Identification of
Management Information for TCP/IP-based Internets", RFC 1155, STD
16, Performance Systems International, Hughes LAN Systems, May 1990
[3] Rose, M., and K. McCloghrie, "Concise MIB Definitions", RFC 1212,
STD 16, Performance Systems International, Hughes LAN Systems,
March 1991
[4] M. Rose, "A Convention for Defining Traps for use with the SNMP",
RFC 1215, Performance Systems International, March 1991
[5] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M.,
and S. Waldbusser, "Structure of Management Information Version 2
(SMIv2)", RFC 2578, STD 58, Cisco Systems, SNMPinfo, TU
Braunschweig, SNMP Research, First Virtual Holdings, International
Network Services, April 1999
[6] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M.,
and S. Waldbusser, "Textual Conventions for SMIv2", RFC 2579, STD
58, Cisco Systems, SNMPinfo, TU Braunschweig, SNMP Research, First
Virtual Holdings, International Network Services, April 1999
[7] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M.,
and S. Waldbusser, "Conformance Statements for SMIv2", RFC 2580,
SNMPCONF WG Expires December 2000 [Page 30]
Internet Draft DiffServ Policy MIB June 2000
STD 58, Cisco Systems, SNMPinfo, TU Braunschweig, SNMP Research,
First Virtual Holdings, International Network Services, April 1999
[8] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple Network
Management Protocol", RFC 1157, STD 15, SNMP Research, Performance
Systems International, Performance Systems International, MIT
Laboratory for Computer Science, May 1990.
[9] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Introduction to Community-based SNMPv2", RFC 1901, SNMP Research,
Inc., Cisco Systems, Inc., Dover Beach Consulting, Inc.,
International Network Services, January 1996.
[10] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Transport
Mappings for Version 2 of the Simple Network Management Protocol
(SNMPv2)", RFC 1906, SNMP Research, Inc., Cisco Systems, Inc.,
Dover Beach Consulting, Inc., International Network Services,
January 1996.
[11] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message
Processing and Dispatching for the Simple Network Management
Protocol (SNMP)", RFC 2572, SNMP Research, Inc., Cabletron Systems,
Inc., BMC Software, Inc., IBM T. J. Watson Research, April 1999
[12] Blumenthal, U., and B. Wijnen, "User-based Security Model (USM) for
version 3 of the Simple Network Management Protocol (SNMPv3)", RFC
2574, IBM T. J. Watson Research, April 1999
[13] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol
Operations for Version 2 of the Simple Network Management Protocol
(SNMPv2)", RFC 1905, SNMP Research, Inc., Cisco Systems, Inc.,
Dover Beach Consulting, Inc., International Network Services,
January 1996.
[14] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications", RFC
2573, SNMP Research, Inc., Secure Computing Corporation, Cisco
Systems, April 1999
[15] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based Access
Control Model (VACM) for the Simple Network Management Protocol
(SNMP)", RFC 2575, IBM T. J. Watson Research, BMC Software, Inc.,
Cisco Systems, Inc., April 1999
[16] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction to
Version 3 of the Internet-standard Network Management Framework",
SNMPCONF WG Expires December 2000 [Page 31]
Internet Draft DiffServ Policy MIB June 2000
RFC 2570, SNMP Research, Inc., TIS Labs at Network Associates,
Inc., Ericsson, Cisco Systems, April 1999
[PBCM] J. Saperia, "Policy-based Configuration Management", Work
in Progress, June 2000.
[DIFFSERVMIB] Baker, F., K. Chan, and A. Smith, Management
Information Base for the Differentiated Services
Architecture, Work in Progress, May 2000.
[POLICYMIB] Waldbusser, S., J. Saperia, T. Hongal, Policy Based
Management MIB, Work in Progress, May 2000.
[SNMPBCP] MacFaden M., J. Saperia, CONFIGURING NETWORKS AND DEVICES
WITH SNMP, Work in Progress, May 2000.
[COPS-PR] Chan, K.H.., D. Durham, S. Gai, S. Herzog, K. McCloghrie, F.
Reichmeyer, J. Seligson, A. Smith, R. Yavatkar, COPS Usage
for Policy Provisioning, Work in Progress, March 2000.
[IPSEC] To be added
[BGP MIB] to be added if necessary.
SNMPCONF WG Expires December 2000 [Page 32]
Internet Draft DiffServ Policy MIB June 2000
Table of Contents
1 Abstract .............................................. 2
2 The SNMP Management Framework ......................... 3
3 Introduction .......................................... 4
4 Definitions ........................................... 4
5 What this MIB Module Provides ......................... 7
6 Relationship to other MIBs ............................ 7
6.1 The Policy-based Management MIB module .............. 7
6.2 The DiffServ MIB module ............................. 8
7 MIB Module Design ..................................... 10
8 Managed objects definitions (MIB module) .............. 12
9 Security Considerations ............................... 29
10 Editors' Addresses ................................... 29
11 Full Copyright Statement ............................. 29
12 References ........................................... 30
SNMPCONF WG Expires December 2000 [Page 33]
| PAFTECH AB 2003-2026 | 2026-04-24 04:39:01 |