One document matched: draft-ietf-rmonmib-dsmon-mib-03.txt
Differences from draft-ietf-rmonmib-dsmon-mib-02.txt
Internet Draft Andy Bierman
Cisco Systems, Inc.
20 November 2000
Remote Monitoring MIB Extensions for
Differentiated Services
<draft-ietf-rmonmib-dsmon-mib-03.txt>
Status of this Memo
This document is an Internet-Draft and is in full conformance with all
provisions of Section 10 of RFC2026 [RFC2026].
Internet-Drafts are working documents of the Internet Engineering Task
Force (IETF), its areas, and its working groups. Note that other groups
may also distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet- Drafts as reference material
or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Distribution of this document is unlimited. Please send comments to the
RMONMIB WG mailing list <rmonmib@ietf.org>.
1. Copyright Notice
Copyright (C) The Internet Society (2000). All Rights Reserved.
Internet Draft DSMON MIB November 2000
2. Abstract
This memo defines an experimental portion of the Management Information
Base (MIB) for use with network management protocols in the Internet
community. In particular, it describes managed objects used for
monitoring Differentiated Services Codepoint usage in IP packets,
utilizing the monitoring framework defined in the RMON-2 MIB [RFC2021].
3. Table of Contents
1 Copyright Notice ................................................ 1
2 Abstract ........................................................ 2
3 Table of Contents ............................................... 2
4 The SNMP Network Management Framework ........................... 2
5 Overview ........................................................ 4
5.1 Terms ......................................................... 4
5.2 Relationship to Differentiated Services ....................... 5
5.3 Relationship to the Remote Monitoring MIBs .................... 5
6 MIB Structure ................................................... 8
6.1 MIB Group Overview ............................................ 9
6.1.1 DSCP Aggregation Control Group .............................. 10
6.1.2 DS Statistics Group ......................................... 11
6.1.3 DS Protocol Distribution Group .............................. 12
6.1.4 DS Host Distribution Group .................................. 12
7 Definitions ..................................................... 14
8 Aggregation Configuration Usage Examples ........................ 78
8.1 Step 1: Unlock the Aggregation Configuration .................. 78
8.2 Step 2: Check the Maximum number of Aggregation Groups ........ 78
8.3 Step 3: Check if the aggregation profiles already exist ....... 78
8.4 Step 4: Create the Aggregation Control Entries ................ 79
8.5 Step 5: Create the Aggregation Group Descriptions ............. 79
8.6 Step 6: Create the Aggregation Profile Mappings ............... 82
8.7 Step 7: Lock the Aggregation Configuration .................... 85
9 Intellectual Property ........................................... 85
10 Acknowledgements ............................................... 86
11 References ..................................................... 86
12 Security Considerations ........................................ 89
13 Author's Address ............................................... 90
14 Full Copyright Statement ....................................... 91
4. The SNMP Network Management Framework
The SNMP Management Framework presently consists of five major
components:
Expires May 20, 2001 [Page 2]
Internet Draft DSMON MIB November 2000
o An overall architecture, described in RFC 2571 [RFC2571].
o Mechanisms for describing and naming objects and events for the
purpose of management. The first version of this Structure of
Management Information (SMI) is called SMIv1 and described in
RFC 1155 [RFC1155], RFC 1212 [RFC1212] and RFC 1215 [RFC1215].
The second version, called SMIv2, is described in RFC 2578
[RFC2578], RFC 2579 [RFC2579] and RFC 2580 [RFC2580].
o Message protocols for transferring management information. The
first version of the SNMP message protocol is called SNMPv1 and
described in RFC 1157 [RFC1157]. A second version of the SNMP
message protocol, which is not an Internet standards track
protocol, is called SNMPv2c and described in RFC 1901 [RFC1901]
and RFC 1906 [RFC1906]. The third version of the message
protocol is called SNMPv3 and described in RFC 1906 [RFC1906],
RFC 2572 [RFC2572] and RFC 2574 [RFC2574].
o Protocol operations for accessing management information. The
first set of protocol operations and associated PDU formats is
described in RFC 1157 [RFC1157]. A second set of protocol
operations and associated PDU formats is described in RFC 1905
[RFC1905].
o A set of fundamental applications described in RFC 2573
[RFC2573] and the view-based access control mechanism described
in RFC 2575 [RFC2575].
A more detailed introduction to the current SNMP Management Framework
can be found in RFC 2570 [RFC2570].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Objects in the MIB are
defined using the mechanisms defined in the SMI.
This memo specifies a MIB module that is compliant to the SMIv2. A
MIB conforming to the SMIv1 can be produced through the appropriate
translations. The resulting translated MIB must be semantically
equivalent, except where objects or events are omitted because no
translation is possible (use of Counter64). Some machine readable
information in SMIv2 will be converted into textual descriptions in
SMIv1 during the translation process. However, this loss of machine
readable information is not considered to change the semantics of the
MIB.
Expires May 20, 2001 [Page 3]
Internet Draft DSMON MIB November 2000
5. Overview
There is a need for a standardized way of monitoring the network traffic
usage of Differentiated Services (DS) [RFC2474] codepoint values. Each
DS codepoint (DSCP) value may be given a different preference by a
forwarding device, and this affects which packets get dropped or delayed
during periods of network congestion.
The IETF DIFFSERV working group has redefined the semantics of the Type
of Service (TOS) octet in the IP header, which is now called the 'DS
field'. The 6-bit Codepoint (DSCP) portion is contained in the DS field,
which provides for 64 different packet treatments for the implementation
of differentiated network services. The actual packet treatment, or per-
hop behavior (PHB), applied by a forwarding device, is independent of a
particular DSCP value.
By polling DSCP usage counters, an NMS can determine the network
throughput for traffic associated with different DSCPs. This data can
then be analyzed in order to 'tune' DSCP 'allocations' within a network,
based on the Quality of Service (QoS) policies for that network.
5.1. Terms
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119. [RFC2119]
This document uses some terms that need introduction:
DataSource
A source of data for monitoring purposes. This term is used exactly
as defined in the RMON-2 MIB [RFC2021].
protocol
A specific protocol encapsulation, as identified for monitoring
purposes. This term is used exactly as defined in the RMON
Protocol Identifiers document [RFC2074].
Aggregation Group
An arbitrary set of DSCP values, grouped together for counting
purposes. For the purposes of this MIB, a aggregation group is
simply a group of codepoints that are being counted in the same
manner (i.e., same buckets), for the purpose of (potentially)
reducing the number of MIB objects that a management station must
retrieve. An aggregation group may be used to model a particular
Expires May 20, 2001 [Page 4]
Internet Draft DSMON MIB November 2000
per-hop behavior (PHB), but such definitions are not specified in
this document.
Aggregation Profile
A set of aggregation group mappings for all 64 DSCP values, which
are applied to all monitored packets on a particular data source.
An agent MUST support at least one aggregation profile
configuration will yields at least two distinct aggregation groups.
An agent MAY choose to restrict configurations such that all DSMON
data collections for the same data source must use the same
aggregation profile.
5.2. Relationship to Differentiated Services
The DSMON MIB is a product of the RMONMIB WG, not the DIFFSERV WG, and
it focuses on monitoring the DSCP values used in IP packets on a
particular dataSource, not the forwarding device configuration or the
per-hop behavior (PHB) semantics associated with each DSCP.
This document assumes the reader is somewhat familiar with the DS
Architecture [RFC2475], It is expected that complex management
applications will use the counters in this MIB to help analyze DS-
related throughput. It is expected that other metrics, such as delay and
jitter, will also be analyzed, but support for other metrics is outside
the scope of this document.
5.3. Relationship to the Remote Monitoring MIBs
This MIB is intended to be implemented in Remote Monitoring (RMON)
probes, which implement the RMON-2 MIB [RFC2021]. Such probes may be
stand-alone devices, or may not be co-located with other networking
devices (e.g., ethernet switches and repeaters).
The DSMON probe MUST be capable of parsing the DS field in IPv4 packets
and correlating the embedded DSCP value with other statistics, as
defined in the DSMON MIB. The DSMON probe SHOULD be capable of
providing the same functions on behalf of IPv6 packets as well.
The DSMON functions are intended to be implemented in conjunction with
the associated RMON functions, but the MIB is independent of all other
RMON data tables. For example, an agent might wish to implement the
RMON-2 protocol distribution group and the DSMON protocol distribution
group, in order to provide the fine granularity, 'per DSCP' statistics
with the DSMON MIB, and the 'grand total' statistics with the RMON-2
MIB.
Expires May 20, 2001 [Page 5]
Internet Draft DSMON MIB November 2000
Several concepts and even MIB objects from the RMON MIBs are used in the
DSMON MIB:
DataSource
This textual convention is used to describe the identification of
an RMON monitoring source (defined in the RMON-2 MIB [RFC2021]).
The DataSource textual convention is used throughout the DSMON MIB
to identify the monitoring source for each configured collection.
A DataSource MIB object is an OBJECT IDENTIFIER, which contains the
particular instance of the ifIndex object associated with the
monitored dataSource.
Protocol Directory
The RMON-2 MIB [RFC2021] defines the protocolDirTable, which is a
directory of all the protocols that the RMON-2 agent is capable of
decoding and counting. The DSMON MIB utilizes this directory to
identify the protocols detected in monitored packets. The
protocolDirLocalIndex MIB object is used to identify protocol
encapsulations in all DSMON data tables which classify and
aggregate by protocol type in some manner.
TimeFilter
The RMON-2 TimeFilter textual convention provides a mechanism to
retrieve only rows which have been created or modified since the
last polling interval (for a particular NMS). The DSMON MIB uses
this textual convention in the large data tables, in order to
minimize polling impact.
Zero-Based Counters
Since counters are instantiated by management action, as in the
RMON MIBs, the DSMON MIB uses zero-based counters in all data
collection tables. Specifically, the ZeroBasedCounter32 textual
convention from the RMON-2 MIB [RFC2021] and the ZeroBasedCounter64
textual convention (defined in the HCNUM-TC MIB [HCNUM]) are used
to define counter objects in this MIB.
High Capacity Counters
The DSMON MIB uses the 'SNMPv1 coexistence' strategy adopted by the
RMONMIB WG. That is, where a 64-bit counter is provided, a 32-bit
version of the counter, and a 32-bit overflow counter are also
provided.
TopN Reports
The DSMON MIB uses the same TopN reporting MIB structure as the
RMON-2 MIB [RFC2021]. TopN reporting can greatly reduce the polling
Expires May 20, 2001 [Page 6]
Internet Draft DSMON MIB November 2000
overhead required to analyze DSCP usage patterns.
Expires May 20, 2001 [Page 7]
Internet Draft DSMON MIB November 2000
6. MIB Structure
Figure 1: DSMON MIB Functional Structure
+---------------+
| |
| Aggregation |
+------------>| Control |<-----------+
| | | |
| +---------------+ |
| ^ |
| | |
| | |
+---------------+ +---------------+ +---------------+
| | | | | |
| Data Source | | Application | | Net. Host |
| Statistics | | Statistics | | Statistics |
| | | | | |
+---------------+ +---------------+ +---------------+
| |
| |
V V
+---------------+ +---------------+
| | | |
| Application | | Net. Host |
| TopN Reports | | TopN Reports |
| | | |
+---------------+ +---------------+
The DSMON MIB can divided into two functional components:
- DSCP Aggregation Control
This set of MIB objects controls how individual DIFFSERV codepoints
are aggregated (for counting purposes) in DSMON data collections.
- DSMON Data Collection
This set of MIB objects controls how individual statistical
collections are maintained by the agent and reported to management
applications.
Expires May 20, 2001 [Page 8]
Internet Draft DSMON MIB November 2000
Figure 2: DSMON Aggregation Configuration
+---------------+
| |
| Aggregation |
| Control | +---------------+
| | | |
+---------------+ +-+-------------+ |
| | | |
| +-+-------------+ | | +---------------+
| | | +-+ | |
+--------->| Aggregation | | +-+-------------+ |
| | Profile +-+ | | |
| | | +-+-------------+ | |
| +---------------+ | | | |
| | | Aggregation | +-+
| +-------------->| Groups for | |
| dsmonAggGroupIndex | one profile +-+
+--------------------------------->| |
dsmonAggControlIndex +---------------+
The DSMON MIB supports the configuration of an arbitrary number of
aggregation profiles. There is a top-level aggregation control
table, which contains one entry for each aggregation profile. A
subordinate aggregation profile table provides information about
each codepoint value in the profile.
Each aggregation profile contains:
- a set of aggregation groups
An aggregation group is only meaningful within the scope of an
individual aggregation profile.
- a set of DSCP mappings
Each DSCP value MUST be mapped into exactly one aggregation group.
Each DSMON data collection MUST select an aggregation profile, and
will convert observed DSCP values into aggregation group index
values, using this set of mappings.
6.1. MIB Group Overview
The DSMON MIB contains four groups of MIB objects:
Expires May 20, 2001 [Page 9]
Internet Draft DSMON MIB November 2000
- dsmonAggregateControl group
Controls the configuration of aggregation groups, for the purpose
of reducing the total number of counters maintained by the agent.
- dsmonStatsObjects group
Report per aggregation group distribution statistics for a
particular RMON dataSource.
- dsmonPdistObjects group
Report per aggregation group distribution statistics for each
protocol detected on a particular RMON dataSource.
- dsmonHostObjects group
Report IP host address distribution statistics for each aggregation
group, detected on a particular RMON dataSource.
6.1.1. DSCP Aggregation Control Group
This group contains 4 scalar objects and three tables, and is used by a
management station to configure aggregation profiles.
The dsmonMaxAggGroups scalar is a read-only integer which indicates the
maximum number of aggregation groups that the agent will allow to be
configured into a single aggregation profile. This value SHOULD be
equal to 64 (the number of codepoints), but an agent MAY limit the
number of aggregation groups because of resource limitations (e.g.,
small number of HW-based counters). At least one aggregation profile
containing at least two aggregation groups MUST be supported by the
agent.
The dsmonAggControlLocked scalar is used as a top level switch,
controlling all write access to the dsmonAggControlTable,
dsmonAggProfileTable, and dsmonAggGroupTable. All 'running counter'
type of DSMON collection data is deleted, and collection suspended,
while this object is equal to 'false', since the meaning of one or more
aggregation control tables may change when it is set back to 'true'.
The dsmonAggControlChanges counter and dsmonAggControlLastChangeTime
timestamp can be used by a management station to detect that the
codepoint to aggregation group mappings may have changed between polls.
The dsmonAggControlTable is a read-create table which contains one entry
for each aggregation profile configured on the agent. Each entry is
identified by a dsmonAggControlIndex value, which is also used as the
Expires May 20, 2001 [Page 10]
Internet Draft DSMON MIB November 2000
major index into the dsmonAggProfileTable and dsmonAggGroupTable. The
DSMON control tables with DataSource objects select an aggregation
profile by referencing this index value. The agent SHOULD save the
active entries in this table in non-volatile storage and recreate them
upon the each restart of the system.
The dsmonAggProfileTable is a read-write table which contains 64 rows
for each associated entry in the dsmonAggControlTable, which MUST be
indexed from 0 to 63. The agent creates this set of 64 instances when
the associated dsmonAggControlEntry is activated, and deletes them when
that dsmonAggControlEntry is deactivated. Each of the 64 rows
represents a DSCP identified by the same dsmonAggProfileDSCP value, and
contains the DSCP to aggregation group mapping for that DSCP, in the
indicated aggregation profile. The agent SHOULD use the value zero as
the initial aggregation group assignment for each entry in this table.
The agent SHOULD save the active entries in this table in non-volatile
storage and recreate them upon the each restart of the system.
The dsmonAggGroupTable contains an administratively assigned descriptive
label for each configured aggregation group. This table is not required
to be properly configured in order for data collection to occur. It is
provided to allow the agent to store a descriptive string for each
configured aggregation group. There is no attempt made to convey any
real semantics for each aggregation group. A management station MAY
choose not to configure entries in this table. The agent SHOULD save
the active entries in this table in non-volatile storage and recreate
them upon the each restart of the system.
6.1.2. DS Statistics Group
This group contains two tables, the dsmonStatsControlTable and the
dsmonStatsTable, and supports aggregation group distribution statistics
for half and full-duplex, low and high speed interfaces. Packet and
octets distributions are maintained in the dsmonStatsTable for each
active control row in the dsmonStatsControlTable.
This group provides the lowest statistics granularity in the DSMON MIB.
It is expected that a management application will analyze certain DS
deployment or performance problems by first examining the aggregation
group distribution for an entire interface with this group.
Expires May 20, 2001 [Page 11]
Internet Draft DSMON MIB November 2000
6.1.3. DS Protocol Distribution Group
This group contains two tables for statistics collection,
(dsmonPdistControlTable and dsmonPdistStatsTable), and two tables for a
'Top N' reporting function for the collected statistics
(dsmonPdistTopNControlTable and dsmonPdistTopNTable).
The dsmonPdistControlTable and dsmonPdistStatsTable tables provide
aggregation group distribution statistics for each selected protocol
encapsulation in packets monitored on a particular dataSource. Packet
and octets distributions (per protocol per aggregation group) are
maintained in the dsmonPdistStatsTable for each active control row in
the dsmonPdistControlTable.
Due the potentially large number of entries, the DS Protocol
Distribution is different from the RMON-2 protocol distribution group in
several ways:
- maximum desired entries parameter added to the control table
- inserts and deletes counters added to the control table
- support for LRU garbage collection in the dsmonPdistStatsTable
- TimeFilter index added to the dsmonPdistStatsTable
- the selection of protocols is not configurable. Rather than select
individual protocols to monitor, (e.g., via a 'supportedOn/Off'
extension to the protocolDirTable [RFC 2021]), a simplified
configuration mechanism is provided. Since DSCP usage statistics
are most interesting at the application layer, the
dsmonPdistStatsTable is 'hardwired' to select only application
layer (i.e., 'terminal') protocols for statistical analysis.
The TopN feature requires two additional tables: the
dsmonPdistTopNControlTable and the dsmonPdistTopNTable, and supports
periodic usage reporting for the statistics maintained in the
dsmonPdistStatsTable. This feature allows for simple periodic retrieval
of the most used application/aggregation group combinations.
6.1.4. DS Host Distribution Group
This group contains two tables for statistics collection,
(dsmonHostControlTable and dsmonHostTable), and two tables for a 'Top N'
Expires May 20, 2001 [Page 12]
Internet Draft DSMON MIB November 2000
reporting function for the collected statistics
(dsmonHostTopNControlTable and dsmonHostTopNTable).
The dsmonHostControlTable and dsmonHostTables provide IP host
distribution statistics for each aggregation group detected in packets
monitored on a particular dataSource.
It is expected that a management application will analyze certain DS
deployment or performance problems by first determining the high
priority DSCP values to examine (beyond the scope of this document) and
then examining the dsmonHostTable statistics to determine which IP hosts
are using the selected aggregation groups.
Packet and octets distributions (in and out, per aggregation group per
IP host) are maintained in the dsmonHostTable for each active control
row in the dsmonHostControlTable.
The DS Host Distribution is different from the RMON-2 network layer host
group in two ways:
- the protocolDirLocalIndex in the INDEX clause MUST identify a
network protocol encapsulation which contains a DS field (e.g.,
IPv4 or IPv6). If a protocol encapsulation with multiple network
layers is specified, then associated entries in this table refer to
the innermost network protocol layer.
- the dsmonHostControlTable supports limited IPv4 and IPv6 prefix
aggregation by allowing the number of 'monitored address bits' in
each address to be configured for each collection. The agent will
zero out the selected number of rightmost address bits for counting
purposes. This configuration parameter can dramatically reduce the
number of entries which must be maintained by the agent, which
should reduce CPU and memory resource requirements on the agent,
and reduce polling overhead on the network and the management
station. However, only one mask can be configured for each address
type, rather than multiple different length masks for each address
type, based on prefix value.
The TopN feature requires two additional tables: the
dsmonHostTopNControlTable and the dsmonHostTopNTable. and supports
periodic usage reporting for the statistics maintained in the
dsmonHostTable. This feature allows for simple periodic retrieval of
the most used IP-host/DSCP combinations.
Expires May 20, 2001 [Page 13]
Internet Draft DSMON MIB November 2000
7. Definitions
-- RMON-2 Extensions for the Monitoring of
-- Differentiated Services Enabled Networks
--
-- IP DIFFSERV DSCP statistics
-- * Per Aggregation Group
-- * Per Protocol Per Aggregation Group
-- * Per Aggregation Group Per IP Host Address
--
--
-- In order to maintain the RMON 'look-and-feel', some of
-- the text from the RMON-2 and HC-RMON MIBs by
-- Steve Waldbusser has been used in this MIB.
--
DSMON-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Integer32,
Counter32, Gauge32, Counter64
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
RowStatus, TimeStamp, TEXTUAL-CONVENTION, TruthValue
FROM SNMPv2-TC
OwnerString, rmon
FROM RMON-MIB
protocolDirLocalIndex, LastCreateTime,
DataSource, ZeroBasedCounter32, TimeFilter
FROM RMON2-MIB
CounterBasedGauge64, ZeroBasedCounter64
FROM HCNUM-TC
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB;
dsmonMIB MODULE-IDENTITY
LAST-UPDATED "200011190000Z"
ORGANIZATION "IETF RMONMIB Working Group"
CONTACT-INFO
" Andy Bierman
Cisco Systems, Inc.
RMONMIB WG Chair and DSMON MIB Editor
Postal: 170 West Tasman Drive
Expires May 20, 2001 [Page 14]
Internet Draft DSMON MIB November 2000
San Jose, CA USA 95134
Tel: +1 408 527-3711
E-mail: abierman@cisco.com
Send comments to <rmonmib@ietf.org>
Mailing list subscription info:
http://www.ietf.org/mailman/listinfo/rmonmib "
DESCRIPTION
"This module defines Remote Monitoring MIB extensions for
Differentiated Services enabled networks."
REVISION "200011190000Z"
DESCRIPTION
"Initial version of the DSMON MIB module. This version
published as RFC xxxx (to be assigned by the RFC Editor)."
::= { rmon 26 }
dsmonObjects OBJECT IDENTIFIER ::= { dsmonMIB 1 }
dsmonNotifications OBJECT IDENTIFIER ::= { dsmonMIB 2 }
dsmonConformance OBJECT IDENTIFIER ::= { dsmonMIB 3 }
dsmonAggObjects OBJECT IDENTIFIER ::= { dsmonObjects 1 }
dsmonStatsObjects OBJECT IDENTIFIER ::= { dsmonObjects 2 }
dsmonPdistObjects OBJECT IDENTIFIER ::= { dsmonObjects 3 }
dsmonHostObjects OBJECT IDENTIFIER ::= { dsmonObjects 4 }
--
-- Textual Convention to define a DSCP for
-- DSMON monitoring purposes
--
DsmonDSCodePoint ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This TC describes an object which identifies the
Differentiated Services Codepoint (DSCP) value found within
the DS field in a network layer packet header (e.g., IPv4
and IPv6)."
REFERENCE
"Definition of the Differentiated Services Field (DS Field)
in the IPv4 and IPv6 Headers [RFC2474]."
SYNTAX Integer32 (0..63)
--
Expires May 20, 2001 [Page 15]
Internet Draft DSMON MIB November 2000
-- Textual Convention to define a
-- DSMON Aggregation Group Index
--
AggGroupIndex ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This TC describes an object which identifies a DSMON
aggregation group, which is an arbitrary grouping of DSCP
values, for monitoring purposes only."
SYNTAX Integer32 (0..2147483647)
--
-- Textual Convention to define a
-- DSMON Aggregation Profile Index
--
AggProfileIndex ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This TC describes an object which identifies a DSMON
aggregation profile, which is a set of aggregation group
assignments for each of the 64 DSCP values, for a particular
statistical collection."
SYNTAX Integer32 (1..2147483647)
-- ***********************************************************
-- * *
-- * A G G R E G A T I O N C O N T R O L G R O U P S *
-- * *
-- ***********************************************************
dsmonMaxAggGroups OBJECT-TYPE
SYNTAX Integer32 (2..64)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of aggregation groups that this agent
can support. The agent will allow this number of distinct
groups to be configured in the dsmonAggProfileTable,
numbered from '0' to 'dsmonMaxAggGroups - 1', for each
aggregation profile entry supported by the agent.
Expires May 20, 2001 [Page 16]
Internet Draft DSMON MIB November 2000
The agent MUST NOT lower this value during system operation,
and SHOULD set this object to an appropriate value during
system initialization."
::= { dsmonAggObjects 1 }
dsmonAggControlLocked OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Controls the setup of aggregation groups for this agent.
If this object contains the value 'true', then write access
to the objects in the dsmonAggControlTable,
dsmonAggProfileTable, and dsmonAggGroupTable is not
permitted, and data collection is possible. This object
only controls write access to these MIB objects. The DSMON
data collection control tables (e.g., dsmonHostControlTable)
can be configured at any time, even if data collection
itself is disabled by this object.
If this object contains the value 'false', write access to
the objects in the dsmonAggControlTable,
dsmonAggProfileTable, and dsmonAggGroupTable is permitted,
and data collection is not possible. In addition, all
objects in all DSMON data tables (e.g., dsmonStatsTable)
shall be deleted.
An agent is not required to process SNMP Set Requests for
this object in conjunction with other objects from this MIB.
This is intended to simplify the processing of Set Requests
for tables such as the dsmonAggProfileTable, by eliminating
the possibility that a single Set PDU will contain multiple
varbinds which are in conflict, such as a PDU which both
modifies the dsmonAggProfileTable and locks the
dsmonAggProfileTable at the same time.
Note that the agent is not required to validate the entire
aggregation configuration when an attempt is made to
transition an instance of this object from 'true' to
'false'. That validation is done if and when a DSMON data
collection is activated.
An agent is required to reactivate any suspended data
collections when this object transitions to 'true', Each
Expires May 20, 2001 [Page 17]
Internet Draft DSMON MIB November 2000
active data control entry (e.g., dsmonStatsControlEntry),
will be validated with respect to the new aggregation
configuration. If the aggregation profile referenced in the
data collection is valid, then that collection will be
restarted. Otherwise, the RowStatus object (e.g.,
dsmonStatsControlStatus) will be set to 'notReady' for that
collection control entry."
::= { dsmonAggObjects 2 }
dsmonAggControlChanges OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of times the value of the
dsmonAggControlLocked object has changed. A management
station can use this object to detect if counters in the
DSMON data tables (e.g., dsmonStatsEntry) have been deleted
and recreated between polls.
This object shall be incremented by one each time the
dsmonAggControlLocked object changes from 'false' to 'true',
or from 'true' to 'false'."
::= { dsmonAggObjects 3 }
dsmonAggControlLastChangeTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies the value of sysUpTime at the moment
the dsmonAggControlLocked object was last modified. A
management station can use this object to detect if counters
in the DSMON data tables (e.g., dsmonStatsEntry) have been
deleted and recreated between polls.
This object shall be updated with the current value of
sysUpTime, if the dsmonAggControlLocked object changes from
'false' to 'true', or from 'true' to 'false'.
Upon system initialization, this object shall contain the
value zero."
::= { dsmonAggObjects 4 }
Expires May 20, 2001 [Page 18]
Internet Draft DSMON MIB November 2000
--
-- Aggregation Control Table
--
dsmonAggControlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonAggControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides an overall description and control
point for all dsmonAggProfileEntries with the same
dsmonAggControlIndex value.
A management application SHOULD create an aggregation
profile by first creating and activating an entry in this
table. This will cause the agent to create a set of 64
dsmonAggProfileEntries on behalf of this control entry. An
application can then set the individual aggregation group
assignments for each of the 64 DSCP values,
This table MUST NOT be modified if the dsmonAggControlLocked
object is equal to 'true'.
Note that an agent MAY choose to limit the actual number of
entries which may be created in this table, and
(independently) the number of aggregation profiles which may
be applied to a particular data source.
If the agent supports non-volatile configuration of this
table, then upon system initialization, the table SHOULD be
initialized with the saved values. Otherwise, each
potential aggregation group description string SHOULD
contain the empty string."
::= { dsmonAggObjects 5 }
dsmonAggControlEntry OBJECT-TYPE
SYNTAX DsmonAggControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonAggControlTable. The
dsmonAggControlIndex value in the INDEX identifies the
aggregation profile associated with each entry."
INDEX { dsmonAggControlIndex }
::= { dsmonAggControlTable 1 }
Expires May 20, 2001 [Page 19]
Internet Draft DSMON MIB November 2000
DsmonAggControlEntry ::= SEQUENCE {
dsmonAggControlIndex AggProfileIndex,
dsmonAggControlDescr SnmpAdminString,
dsmonAggControlOwner OwnerString,
dsmonAggControlStatus RowStatus
}
dsmonAggControlIndex OBJECT-TYPE
SYNTAX AggProfileIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary integer index value used to identify the
aggregation profile specified by this control entry."
::= { dsmonAggControlEntry 1 }
dsmonAggControlDescr OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..64))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An administratively assigned description of the aggregation
profile identified by this entry.
Upon first instantiation of this object, the agent SHOULD
set this object to the empty string. If the agent supports
non-volatile storage, then this object SHOULD be re-
initialized with its stored value after a system reboot.
This object MUST NOT be modified if the associated
dsmonAggControlStatus object is equal to 'active', or the
dsmonAggControlLocked object is equal to 'true'."
::= { dsmonAggControlEntry 2 }
dsmonAggControlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonAggControlEntry 3 }
dsmonAggControlStatus OBJECT-TYPE
SYNTAX RowStatus
Expires May 20, 2001 [Page 20]
Internet Draft DSMON MIB November 2000
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
Upon setting this object to active(1), the agent will create
a complete set of 64 associated entries in the
dsmonAggProfileTable.
If this object is not equal to active(1), all associated
entries in the dsmonAggProfileTable shall be deleted.
This object MUST NOT be modified if the
dsmonAggControlLocked object is equal to 'true'."
::= { dsmonAggControlEntry 4 }
--
-- Aggregation Profile Table
--
dsmonAggProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonAggProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Controls the setup of aggregation profiles for this agent.
For each such profile, every DSCP value MUST be configured
into exactly one aggregation group.
This table MUST NOT be modified if the dsmonAggControlLocked
object is equal to 'true'.
The agent will create a set of 64 entries in this table
(with the same dsmonAggControlIndex value) when the
associated dsmonAggControlEntry is activated.
If the agent supports non-volatile configuration of this
table, then upon system initialization, this table SHOULD be
initialized with the saved values. Otherwise, an agent
SHOULD initially configuring each DSCP value in the same
aggregation group."
Expires May 20, 2001 [Page 21]
Internet Draft DSMON MIB November 2000
::= { dsmonAggObjects 6 }
dsmonAggProfileEntry OBJECT-TYPE
SYNTAX DsmonAggProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonAggProfileTable. The
dsmonAggControlIndex value in the index identifies the
dsmonAggControlEntry associated with each entry in this
table."
INDEX { dsmonAggControlIndex, dsmonAggProfileDSCP }
::= { dsmonAggProfileTable 1 }
DsmonAggProfileEntry ::= SEQUENCE {
dsmonAggProfileDSCP DsmonDSCodePoint,
dsmonAggGroupIndex AggGroupIndex
}
dsmonAggProfileDSCP OBJECT-TYPE
SYNTAX DsmonDSCodePoint
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The specific DSCP value which is configured in an
aggregation group by this entry."
::= { dsmonAggProfileEntry 1 }
dsmonAggGroupIndex OBJECT-TYPE
SYNTAX AggGroupIndex
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The aggregation group which contains this DSCP value.
This object MUST NOT be modified if the
dsmonAggControlLocked object is equal to 'true'."
::= { dsmonAggProfileEntry 2 }
--
-- Aggregation Group Table
--
Expires May 20, 2001 [Page 22]
Internet Draft DSMON MIB November 2000
dsmonAggGroupTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonAggGroupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides a description of each aggregation group
configured on this system. Note that the semantics of a
particular aggregation group are only relevant within the
scope of a particular aggregation profile.
This table MUST NOT be modified if the dsmonAggControlLocked
object is equal to 'true'.
Note that an agent MAY choose to limit the actual number of
entries which may be created in this table, and
(independently) the number of aggregation profiles which may
be applied to a particular data source.
If the agent supports non-volatile configuration of this
table, then upon system initialization, this table SHOULD be
initialized with the saved values. Otherwise, each
potential aggregation group description string SHOULD
contain the empty string.
An agent SHOULD allow entries to be created or modified in
this table, even if the specified dsmonAggControlIndex value
does not identify a valid dsmonAggControlEntry or a complete
set of valid dsmonAggProfileEntries, to reduce row creation
order dependencies."
::= { dsmonAggObjects 7 }
dsmonAggGroupEntry OBJECT-TYPE
SYNTAX DsmonAggGroupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonAggGroupTable. The
dsmonAggGroupIndex value in the INDEX identifies the
aggregation group associated with each entry.
The dsmonAggControlIndex in the index identifies the
aggregation profile associated with each entry, identified
by the dsmonAggControlEntry and dsmonAggProfileEntries with
the same index value.
Expires May 20, 2001 [Page 23]
Internet Draft DSMON MIB November 2000
The dsmonAggGroupIndex in the index identifies the
aggregation group associated with each entry. This object
SHOULD be indexed from zero to 'N', where 'N' is less than
the value of the dsmonMaxAggGroups for this agent."
INDEX { dsmonAggControlIndex, dsmonAggGroupIndex }
::= { dsmonAggGroupTable 1 }
DsmonAggGroupEntry ::= SEQUENCE {
dsmonAggGroupDescr SnmpAdminString,
dsmonAggGroupStatus RowStatus
}
dsmonAggGroupDescr OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..64))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An administratively assigned description of the aggregation
group identified by this entry.
Upon first instantiation of this object, the agent SHOULD
set this object to the empty string.
This object MUST NOT be modified if the associated
dsmonAggGroupStatus object is equal to 'active', or the
dsmonAggControlLocked object is equal to 'true'."
::= { dsmonAggGroupEntry 1 }
dsmonAggGroupStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
This object MUST NOT be modified if the
dsmonAggControlLocked object is equal to 'true'."
::= { dsmonAggGroupEntry 2 }
Expires May 20, 2001 [Page 24]
Internet Draft DSMON MIB November 2000
-- ***********************************************************
-- * *
-- * P E R - D A T A S O U C E C O L L E C T I O N S *
-- * *
-- ***********************************************************
--
-- Per-DataSource Statistics Control Table
--
dsmonStatsControlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonStatsControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Controls the setup of per data source per aggregation group
distribution statistics."
::= { dsmonStatsObjects 1 }
dsmonStatsControlEntry OBJECT-TYPE
SYNTAX DsmonStatsControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonStatsControlTable.
Entries are created and deleted from this table by
management action only, using the dsmonStatsControlStatus
RowStatus object.
Activation of a control row in this table will cause an
associated dsmonStatsTable to be created and maintained by
the agent."
INDEX { dsmonStatsControlIndex }
::= { dsmonStatsControlTable 1 }
DsmonStatsControlEntry ::= SEQUENCE {
dsmonStatsControlIndex Integer32,
dsmonStatsControlDataSource DataSource,
dsmonStatsControlAggProfile AggProfileIndex,
dsmonStatsControlDroppedFrames Counter32,
dsmonStatsControlCreateTime LastCreateTime,
dsmonStatsControlOwner OwnerString,
dsmonStatsControlStatus RowStatus
}
Expires May 20, 2001 [Page 25]
Internet Draft DSMON MIB November 2000
dsmonStatsControlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary and unique index for this
dsmonStatsControlEntry."
::= { dsmonStatsControlEntry 1 }
dsmonStatsControlDataSource OBJECT-TYPE
SYNTAX DataSource
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The source of data for the this per protocol per
aggregation group distribution.
Note that only packets that contain a network protocol
encapsulation which contains a DS field [RFC2474] will be
counted in this table.
This object MUST NOT be modified if the associated
dsmonStatsControlStatus object is equal to active(1)."
::= { dsmonStatsControlEntry 2 }
dsmonStatsControlAggProfile OBJECT-TYPE
SYNTAX AggProfileIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The dsmonAggControlIndex value identifying the aggregation
profile which should be used on behalf of this
dsmonStatsControlEntry.
The associated dsmonAggControlEntry and
dsmonAggProfileEntries, identified by the same
dsmonAggControlIndex index value, MUST be active in order
for this entry to remain active. It is possible for the
aggregation configuration to change from a valid to invalid
state for this dsmonStats collection. In this case, the
associated dsmonStatsControlStatus object will be changed to
the 'notReady' state, and data collection will not occur on
behalf of this control entry.
Note that an agent MAY choose to limit the actual number of
Expires May 20, 2001 [Page 26]
Internet Draft DSMON MIB November 2000
aggregation profiles which may be applied to a particular
data source.
This object MUST NOT be modified if the associated
dsmonStatsControlStatus object is equal to active(1)."
::= { dsmonStatsControlEntry 3 }
dsmonStatsControlDroppedFrames OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames which were received by the probe
and therefore not accounted for in the *StatsDropEvents, but
for which the probe chose not to count for this entry for
whatever reason. Most often, this event occurs when the
probe is out of some resources and decides to shed load from
this collection.
This count does not include packets that were not counted
because they had MAC-layer errors.
Note that, unlike the dropEvents counter, this number is the
exact number of frames dropped."
::= { dsmonStatsControlEntry 4 }
dsmonStatsControlCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this control entry was last
activated. This can be used by the management station to
detect if the table has been deleted and recreated between
polls."
::= { dsmonStatsControlEntry 5 }
dsmonStatsControlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
Expires May 20, 2001 [Page 27]
Internet Draft DSMON MIB November 2000
::= { dsmonStatsControlEntry 6 }
dsmonStatsControlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonStatsTable shall be deleted."
::= { dsmonStatsControlEntry 7 }
--
-- Per-DataSource Statistics Table
--
dsmonStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information on Per Protocol per aggregation group
usage.
The following table defines per aggregation group statistics
for full and/or half-duplex links as well as high capacity
links.
For half-duplex links, or full-duplex-capable links
operating in half-duplex mode, the dsmonStatsIn* objects
shall be used and the dsmonStatsOut* objects will not
increment.
For full-duplex links, the dsmonStatsOut* objects will be
present. Whenever possible, the probe SHOULD count packets
moving away from the closest terminating equipment as output
packets. Failing that, the probe SHOULD count packets moving
away from the DTE as output packets.
If the dsmonAggControlLocked object is equal to 'false',
then all entries in this table will be deleted and the agent
Expires May 20, 2001 [Page 28]
Internet Draft DSMON MIB November 2000
will not process packets on behalf of any
dsmonStatsControlEntry."
::= { dsmonStatsObjects 2 }
dsmonStatsEntry OBJECT-TYPE
SYNTAX DsmonStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information on Differentiated Services DSCP
usage, containing inbound and outbound packet and octet
counters for each aggregation group configured for
collection.
The dsmonStatsControlIndex value in the index identifies the
dsmonStatsControlEntry on whose behalf this entry was
created.
The dsmonAggGroupIndex value in the index is determined by
examining the DSCP value in each monitored packet, and the
dsmonAggProfileTable entry for that DSCP value.
Note that only packets that contain a network protocol
encapsulation which contains a DS field [RFC2474] will be
counted in this table.
An example of the indexing of this entry is
dsmonStatsOutPkts.1.16"
INDEX { dsmonStatsControlIndex, dsmonAggGroupIndex }
::= { dsmonStatsTable 1 }
DsmonStatsEntry ::= SEQUENCE {
dsmonStatsInPkts ZeroBasedCounter32,
dsmonStatsInOctets ZeroBasedCounter32,
dsmonStatsInOvflPkts ZeroBasedCounter32,
dsmonStatsInOvflOctets ZeroBasedCounter32,
dsmonStatsInHCPkts ZeroBasedCounter64,
dsmonStatsInHCOctets ZeroBasedCounter64,
dsmonStatsOutPkts ZeroBasedCounter32,
dsmonStatsOutOctets ZeroBasedCounter32,
dsmonStatsOutOvflPkts ZeroBasedCounter32,
dsmonStatsOutOvflOctets ZeroBasedCounter32,
dsmonStatsOutHCPkts ZeroBasedCounter64,
dsmonStatsOutHCOctets ZeroBasedCounter64
}
Expires May 20, 2001 [Page 29]
Internet Draft DSMON MIB November 2000
dsmonStatsInPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets using one of the DSCP values in the
indicated aggregation group, received on a half-duplex link
or on the inbound connection of a full-duplex link."
::= { dsmonStatsEntry 1 }
dsmonStatsInOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets in packets, using one of the DSCP
values in the indicated aggregation group, received on a
half-duplex link or on the inbound connection of a full-
duplex link."
::= { dsmonStatsEntry 2 }
dsmonStatsInOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonStatsInPkts counter
has overflowed. Note that this object will only be
instantiated if the associated dsmonStatsInHCPkts object is
also instantiated for a particular dataSource."
::= { dsmonStatsEntry 3 }
dsmonStatsInOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonStatsInOctets
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonStatsInHCOctets object
is also instantiated for a particular dataSource."
Expires May 20, 2001 [Page 30]
Internet Draft DSMON MIB November 2000
::= { dsmonStatsEntry 4 }
dsmonStatsInHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonStatsInPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity RMON for a particular
dataSource."
::= { dsmonStatsEntry 5 }
dsmonStatsInHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonStatsInOctets object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity RMON for a particular
dataSource."
::= { dsmonStatsEntry 6 }
dsmonStatsOutPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets using one of the DSCP values in the
indicated aggregation group, received on a full-duplex link
in the direction of the network."
::= { dsmonStatsEntry 7 }
dsmonStatsOutOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Expires May 20, 2001 [Page 31]
Internet Draft DSMON MIB November 2000
"The number of octets in packets, using one of the DSCP
values in the indicated aggregation group, received on a
full-duplex link in the direction of the network."
::= { dsmonStatsEntry 8 }
dsmonStatsOutOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonStatsOutPkts
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonStatsOutHCPkts object is
also instantiated for a particular dataSource."
::= { dsmonStatsEntry 9 }
dsmonStatsOutOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonStatsOutOctets
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonStatsOutHCOctets object
is also instantiated for a particular dataSource."
::= { dsmonStatsEntry 10 }
dsmonStatsOutHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonStatsOutPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity RMON for a particular
dataSource."
::= { dsmonStatsEntry 11 }
dsmonStatsOutHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
Expires May 20, 2001 [Page 32]
Internet Draft DSMON MIB November 2000
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonStatsOutOctets object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity RMON for a particular
dataSource."
::= { dsmonStatsEntry 12 }
-- ***********************************************************
-- * *
-- * P E R - P R O T O C O L C O L L E C T I O N S *
-- * *
-- ***********************************************************
--
-- DSCP Per-Protocol Statistics Control Table
--
dsmonPdistControlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonPdistControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Controls the setup of per application per aggregation group
distribution statistics."
::= { dsmonPdistObjects 1 }
dsmonPdistControlEntry OBJECT-TYPE
SYNTAX DsmonPdistControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonPdistControlTable.
Entries are created and deleted from this table by
management action only, using the dsmonPdistControlStatus
RowStatus object.
Activation of a control row in this table will cause an
associated dsmonPdistStatsTable to be created and maintained
by the agent."
INDEX { dsmonPdistControlIndex }
Expires May 20, 2001 [Page 33]
Internet Draft DSMON MIB November 2000
::= { dsmonPdistControlTable 1 }
DsmonPdistControlEntry ::= SEQUENCE {
dsmonPdistControlIndex Integer32,
dsmonPdistControlDataSource DataSource,
dsmonPdistControlAggProfile AggProfileIndex,
dsmonPdistControlMaxDesiredEntries Integer32,
dsmonPdistControlDroppedFrames Counter32,
dsmonPdistControlInserts Counter32,
dsmonPdistControlDeletes Counter32,
dsmonPdistControlCreateTime LastCreateTime,
dsmonPdistControlOwner OwnerString,
dsmonPdistControlStatus RowStatus
}
dsmonPdistControlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary and unique index for this
dsmonPdistControlEntry."
::= { dsmonPdistControlEntry 1 }
dsmonPdistControlDataSource OBJECT-TYPE
SYNTAX DataSource
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The source of data for the this per protocol aggregation
group distribution.
This object MUST NOT be modified if the associated
dsmonPdistControlStatus object is equal to active(1)."
::= { dsmonPdistControlEntry 2 }
dsmonPdistControlAggProfile OBJECT-TYPE
SYNTAX AggProfileIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The dsmonAggControlIndex value identifying the aggregation
profile which should be used on behalf of this
dsmonPdistControlEntry.
Expires May 20, 2001 [Page 34]
Internet Draft DSMON MIB November 2000
The associated dsmonAggControlEntry and
dsmonAggProfileEntries, identified by the same
dsmonAggControlIndex index value, MUST be active in order
for this entry to remain active. It is possible for the
aggregation configuration to change from a valid to invalid
state for this dsmonPdist collection. In this case, the
associated dsmonPdistControlStatus object will be changed to
the 'notReady' state, and data collection will not occur on
behalf of this control entry.
Note that an agent MAY choose to limit the actual number of
aggregation profiles which may be applied to a particular
data source.
This object MUST NOT be modified if the associated
dsmonPdistControlStatus object is equal to active(1)."
::= { dsmonPdistControlEntry 3 }
dsmonPdistControlMaxDesiredEntries OBJECT-TYPE
SYNTAX Integer32 (-1 | 1..2147483647)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of entries that are desired in the
dsmonPdistStatsTable on behalf of this control entry. The
probe will not create more than this number of associated
entries in the table, but MAY choose to create fewer entries
in this table for any reason including the lack of
resources.
If this value is set to -1, the probe MAY create any number
of entries in this table.
This object MUST NOT be modified if the associated
dsmonPdistControlStatus object is equal to active(1)."
::= { dsmonPdistControlEntry 4 }
dsmonPdistControlDroppedFrames OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames which were received by the probe
and therefore not accounted for in the *StatsDropEvents, but
Expires May 20, 2001 [Page 35]
Internet Draft DSMON MIB November 2000
for which the probe chose not to count for this entry for
whatever reason. Most often, this event occurs when the
probe is out of some resources and decides to shed load from
this collection.
This count does not include packets that were not counted
because they had MAC-layer errors.
Note that, unlike the dropEvents counter, this number is the
exact number of frames dropped."
::= { dsmonPdistControlEntry 5 }
dsmonPdistControlInserts OBJECT-TYPE
SYNTAX Counter32
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a dsmonPdist entry has been inserted
into the dsmonPdistTable. If an entry is inserted, then
deleted, and then inserted, this counter will be incremented
by 2.
To allow for efficient implementation strategies, agents MAY
delay updating this object for short periods of time. For
example, an implementation strategy may allow internal data
structures to differ from those visible via SNMP for short
periods of time. This counter may reflect the internal data
structures for those short periods of time.
Note that the table size can be determined by subtracting
dsmonPdistControlDeletes from dsmonPdistControlInserts."
::= { dsmonPdistControlEntry 6 }
dsmonPdistControlDeletes OBJECT-TYPE
SYNTAX Counter32
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a dsmonPdist entry has been deleted
from the dsmonPdist table (for any reason). If an entry is
deleted, then inserted, and then deleted, this counter will
be incremented by 2.
Expires May 20, 2001 [Page 36]
Internet Draft DSMON MIB November 2000
To allow for efficient implementation strategies, agents MAY
delay updating this object for short periods of time. For
example, an implementation strategy may allow internal data
structures to differ from those visible via SNMP for short
periods of time. This counter may reflect the internal data
structures for those short periods of time.
Note that the table size can be determined by subtracting
dsmonPdistControlDeletes from dsmonPdistControlInserts."
::= { dsmonPdistControlEntry 7 }
dsmonPdistControlCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this control entry was last
activated. This can be used by the management station to
detect if the table has been deleted and recreated between
polls."
::= { dsmonPdistControlEntry 8 }
dsmonPdistControlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonPdistControlEntry 9 }
dsmonPdistControlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonPdistStatsTable shall be deleted."
::= { dsmonPdistControlEntry 10 }
Expires May 20, 2001 [Page 37]
Internet Draft DSMON MIB November 2000
--
-- Per-Protocol Statistics Table
--
dsmonPdistStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonPdistStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information on a per protocol per aggregation
group usage.
If the dsmonAggControlLocked object is equal to 'false',
then all entries in this table will be deleted and the agent
will not process packets on behalf of any
dsmonPdistControlEntry."
::= { dsmonPdistObjects 2 }
dsmonPdistStatsEntry OBJECT-TYPE
SYNTAX DsmonPdistStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information on Differentiated Services DSCP
usage, containing packet and octet counters for each
aggregation group configured for collection, and each
protocol (as identified by the protocolDirLocalIndex for the
protocol) identified in each monitored packet.
The dsmonPdistControlIndex value in the index identifies the
dsmonPdistControlEntry on whose behalf this entry was
created.
Note that only packets that contain a network protocol
encapsulation which contains a DS field [RFC2474] will be
counted in this table.
The agent will include only application layer protocols in
the associated dsmonPdistStatsTable. Any 'terminal' protocol
is considered to be an application protocol.
The dsmonAggGroupIndex value in the index is determined by
examining the DSCP value in each monitored packet, and the
dsmonAggProfileTable entry for that value.
Expires May 20, 2001 [Page 38]
Internet Draft DSMON MIB November 2000
An example of the indexing of this entry is
dsmonPdistStatsPkts.9.29943.42.0."
INDEX { dsmonPdistControlIndex,
dsmonPdistTimeMark,
protocolDirLocalIndex,
dsmonAggGroupIndex }
::= { dsmonPdistStatsTable 1 }
DsmonPdistStatsEntry ::= SEQUENCE {
dsmonPdistTimeMark TimeFilter,
dsmonPdistStatsPkts ZeroBasedCounter32,
dsmonPdistStatsOctets ZeroBasedCounter32,
dsmonPdistStatsOvflPkts ZeroBasedCounter32,
dsmonPdistStatsOvflOctets ZeroBasedCounter32,
dsmonPdistStatsHCPkts ZeroBasedCounter64,
dsmonPdistStatsHCOctets ZeroBasedCounter64,
dsmonPdistStatsCreateTime LastCreateTime
}
dsmonPdistTimeMark OBJECT-TYPE
SYNTAX TimeFilter
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Time Filter index for this table. This object may be
used by a management station to retrieve only rows which
have been created or modified since a particular time. Note
that the current value for a row are always returned and the
TimeFilter is not a historical data archiving mechanism.
Refer to RFC 2021 [RFC2021] for a detailed description of
TimeFilter operation."
::= { dsmonPdistStatsEntry 1 }
dsmonPdistStatsPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets, using one of the DSCP values in the
indicated aggregation group, for the protocol identified by
the associated protocolDirLocalIndex value."
::= { dsmonPdistStatsEntry 2 }
dsmonPdistStatsOctets OBJECT-TYPE
Expires May 20, 2001 [Page 39]
Internet Draft DSMON MIB November 2000
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets in packets, using one of the DSCP
values in the indicated aggregation group, for the protocol
identified by the associated protocolDirLocalIndex value.
Note that this object doesn't count just those octets in the
particular protocol frames, but includes the entire packet
that contained the protocol."
::= { dsmonPdistStatsEntry 3 }
dsmonPdistStatsOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonPdistStatsPkts
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonPdistStatsHCPkts object
is also instantiated for a particular dataSource."
::= { dsmonPdistStatsEntry 4 }
dsmonPdistStatsOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonPdistStatsOctets
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonPdistStatsHCOctets
object is also instantiated for a particular dataSource."
::= { dsmonPdistStatsEntry 5 }
dsmonPdistStatsHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonPdistStatsPkts object.
Expires May 20, 2001 [Page 40]
Internet Draft DSMON MIB November 2000
Note that this object will only be instantiated if the RMON
agent supports High Capacity RMON for a particular
dataSource."
::= { dsmonPdistStatsEntry 6 }
dsmonPdistStatsHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonPdistStatsOctets object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity RMON for a particular
dataSource."
::= { dsmonPdistStatsEntry 7 }
dsmonPdistStatsCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this dsmonPdistStats entry was
last instantiated by the agent. This can be used by the
management station to detect if the entry has been deleted
and recreated between polls."
::= { dsmonPdistStatsEntry 8 }
--
-- Per-Protocol Statistics TopN Control Table
--
dsmonPdistTopNControlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonPdistTopNControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of parameters that control the creation of a report
of the top N dsmonPdist entries according to a selected
metric."
::= { dsmonPdistObjects 3 }
dsmonPdistTopNControlEntry OBJECT-TYPE
Expires May 20, 2001 [Page 41]
Internet Draft DSMON MIB November 2000
SYNTAX DsmonPdistTopNControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonPdistTopNControlTable.
Entries are created and deleted from this table by
management action only, using the
dsmonPdistTopNControlStatus RowStatus object.
Activation of a control row in this table will cause an
associated dsmonPdistTopNTable to be created and maintained
by the agent."
INDEX { dsmonPdistTopNControlIndex }
::= { dsmonPdistTopNControlTable 1 }
DsmonPdistTopNControlEntry ::= SEQUENCE {
dsmonPdistTopNControlIndex Integer32,
dsmonPdistTopNControlPdistIndex Integer32,
dsmonPdistTopNControlRateBase INTEGER,
dsmonPdistTopNControlTimeRemaining Integer32,
dsmonPdistTopNControlGeneratedReports Counter32,
dsmonPdistTopNControlDuration Integer32,
dsmonPdistTopNControlRequestedSize Integer32,
dsmonPdistTopNControlGrantedSize Integer32,
dsmonPdistTopNControlStartTime TimeStamp,
dsmonPdistTopNControlOwner OwnerString,
dsmonPdistTopNControlStatus RowStatus
}
dsmonPdistTopNControlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
dsmonPdistTopNControlTable. Each such entry defines one Top
N report prepared for one RMON dataSource."
::= { dsmonPdistTopNControlEntry 1 }
dsmonPdistTopNControlPdistIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
Expires May 20, 2001 [Page 42]
Internet Draft DSMON MIB November 2000
"The dsmonPdistTable for which a top N report will be
prepared on behalf of this entry. The dsmonPdistTable is
identified by the value of the dsmonPdistControlIndex for
that table - that value is used here to identify the
particular table.
This object MUST NOT be modified if the associated
dsmonPdistTopNControlStatus object is equal to active(1)."
::= { dsmonPdistTopNControlEntry 2 }
dsmonPdistTopNControlRateBase OBJECT-TYPE
SYNTAX INTEGER {
dsmonPdistTopNPkts(1),
dsmonPdistTopNOctets(2),
dsmonPdistTopNHCPkts(3),
dsmonPdistTopNHCOctets(4),
dsmonPdistTopNObsolete(5)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The variable for each dsmonPdist that the
dsmonPdistTopNRate and dsmonPdistTopNHCRate variables are
based upon. Each dsmonPdistTopN report generated on behalf
of this control entry will be ranked in descending order,
based on the associated dsmonPdistStatsTable counter,
identified by this object.
The following table identifies the dsmonPdistTable counter
associated with each enumeration:
Enumeration RateBase MIB Object
----------- -------------------
dsmonPdistTopNPkts dsmonPdistStatsPkts
dsmonPdistTopNOctets dsmonPdistStatsOctets
dsmonPdistTopNHCPkts dsmonPdistStatsHCPkts
dsmonPdistTopNHCOctets dsmonPdistStatsHCOctets
dsmonPdistTopNObsolete <not specified here>
This object SHOULD be set to the value
'dsmonPdistTopNObsolete(5)', if an updated version of this
object has been created in another MIB module, and this rate
base MIB object is no longer used.
Note that the dsmonPdistTopNHCPkts and
dsmonPdistTopNHCOctets enumerations are only available if
Expires May 20, 2001 [Page 43]
Internet Draft DSMON MIB November 2000
the agent supports High Capacity RMON collection.
This object MUST NOT be modified if the associated
dsmonPdistTopNControlStatus object is equal to active(1)."
::= { dsmonPdistTopNControlEntry 3 }
dsmonPdistTopNControlTimeRemaining OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds left in the report currently being
collected. When this object is modified by the management
station, a new collection is started, possibly aborting a
currently running report. The new value is used as the
requested duration of this report, and is immediately loaded
into the associated dsmonPdistTopNControlDuration object.
When the report finishes, the probe will automatically start
another collection with the same initial value of
dsmonPdistTopNControlTimeRemaining. Thus the management
station may simply read the resulting reports repeatedly,
checking the startTime and duration each time to ensure that
a report was not missed or that the report parameters were
not changed.
While the value of this object is non-zero, it decrements by
one per second until it reaches zero. At the time that this
object decrements to zero, the report is made accessible in
the dsmonPdistTopNTable, overwriting any report that may be
there.
When this object is modified by the management station, any
associated entries in the dsmonPdistTopNTable shall be
deleted."
DEFVAL { 1800 }
::= { dsmonPdistTopNControlEntry 4 }
dsmonPdistTopNControlGeneratedReports OBJECT-TYPE
SYNTAX Counter32
UNITS "reports"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Expires May 20, 2001 [Page 44]
Internet Draft DSMON MIB November 2000
"The number of reports that have been generated by this
entry."
::= { dsmonPdistTopNControlEntry 5 }
dsmonPdistTopNControlDuration OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of seconds that this report has collected during
the last sampling interval.
When the associated dsmonPdistTopNControlTimeRemaining
object is set, this object shall be set by the probe to the
same value and shall not be modified until the next time the
dsmonPdistTopNControlTimeRemaining is set.
This value shall be zero if no reports have been requested
for this dsmonPdistTopNControlEntry."
::= { dsmonPdistTopNControlEntry 6 }
dsmonPdistTopNControlRequestedSize OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "table entries"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of dsmonPdist entries requested for this
report.
When this object is created or modified, the probe SHOULD
set dsmonPdistTopNControlGrantedSize as closely to this
object as is possible for the particular probe
implementation and available resources."
DEFVAL { 150 }
::= { dsmonPdistTopNControlEntry 7 }
dsmonPdistTopNControlGrantedSize OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of dsmonPdist entries in this report.
Expires May 20, 2001 [Page 45]
Internet Draft DSMON MIB November 2000
When the associated dsmonPdistTopNControlRequestedSize
object is created or modified, the probe SHOULD set this
object as closely to the requested value as is possible for
the particular implementation and available resources. The
probe MUST NOST lower this value except as a result of a set
to the associated dsmonPdistTopNControlRequestedSize object.
When the associated dsmonPdistTopNControlRequestedSize
object is created or modified, the probe SHOULD set this
object as closely to the requested value as is possible for
the particular implementation and available resources. The
probe MUST NOT lower this value except as a result of a set
to the associated dsmonPdistTopNControlRequestedSize object.
Protocol entries with the highest value of
dsmonPdistTopNRate or dsmonPdistTopNHCRate (depending on the
value of the associated dsmonPdistTopNControlRateBase
object) shall be placed in this table in decreasing order of
this rate until there is no more room or until there are no
more dsmonPdist entries."
::= { dsmonPdistTopNControlEntry 8 }
dsmonPdistTopNControlStartTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this top N report was last
started. In other words, this is the time that the
associated dsmonPdistTopNControlTimeRemaining object was
modified to start the requested report or the time the
report was last automatically (re)started.
This object may be used by the management station to
determine if a report was missed or not."
::= { dsmonPdistTopNControlEntry 9 }
dsmonPdistTopNControlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonPdistTopNControlEntry 10 }
Expires May 20, 2001 [Page 46]
Internet Draft DSMON MIB November 2000
dsmonPdistTopNControlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this dsmonPdistTopNControlEntry.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonPdistTopNTable shall be deleted by the
agent."
::= { dsmonPdistTopNControlEntry 11 }
--
-- dsmonPdist TopN Table
--
dsmonPdistTopNTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonPdistTopNEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of statistics for those protocol distribution entries
that have counted the highest number of octets or packets.
If the dsmonAggControlLocked object is equal to 'false',
then all entries in this table SHALL be deleted, and the
agent will not process TopN reports on behalf of any
dsmonPdistTopNControlEntry.
When the dsmonAggControlLocked object is set to 'true', then
particular reports SHOULD be restarted from the beginning,
on behalf of all active rows in the
dsmonPdistTopNControlTable.
Note that dsmonPdist entries which did not increment at all
during the report interval SHOULD NOT be included in
dsmonPdistTopN reports."
::= { dsmonPdistObjects 4 }
dsmonPdistTopNEntry OBJECT-TYPE
SYNTAX DsmonPdistTopNEntry
MAX-ACCESS not-accessible
Expires May 20, 2001 [Page 47]
Internet Draft DSMON MIB November 2000
STATUS current
DESCRIPTION
"A conceptual row in the dsmonPdistTopNTable.
The dsmonPdistTopNControlIndex value in the index identifies
the dsmonPdistTopNControlEntry on whose behalf this entry
was created."
INDEX { dsmonPdistTopNControlIndex, dsmonPdistTopNIndex }
::= { dsmonPdistTopNTable 1 }
DsmonPdistTopNEntry ::= SEQUENCE {
dsmonPdistTopNIndex Integer32,
dsmonPdistTopNPDLocalIndex Integer32,
dsmonPdistTopNAggGroup AggGroupIndex,
dsmonPdistTopNRate Gauge32,
dsmonPdistTopNRateOvfl Gauge32,
dsmonPdistTopNHCRate CounterBasedGauge64
}
dsmonPdistTopNIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
dsmonPdistTopNTable among those in the same report. This
index is between 1 and N, where N is the number of entries
in this report."
::= { dsmonPdistTopNEntry 1 }
dsmonPdistTopNPDLocalIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The protocolDirLocalIndex value which identifies the
protocol associated with this entry.
If the protocolDirEntry associated with the
protocolDirLocalIndex with the same value as this object is
de-activated or deleted, then the agent MUST delete this
dsmonPdistTopN entry."
::= { dsmonPdistTopNEntry 2 }
dsmonPdistTopNAggGroup OBJECT-TYPE
Expires May 20, 2001 [Page 48]
Internet Draft DSMON MIB November 2000
SYNTAX AggGroupIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The DSCP aggregation group index value associated with
protocol identified in this entry."
::= { dsmonPdistTopNEntry 3 }
dsmonPdistTopNRate OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of change in the selected variable during this
sampling interval. The selected variable is this protocol's
instance of the object selected by
dsmonPdistTopNControlRateBase.
If the associated dsmonPdistTopNControlRateBase is equal to
'dsmonPdistTopNHCPkts' or 'dsmonPdistTopNHCOctets', then
this object will contain the the least significant 32 bits
of the associated dsmonPdistTopNHCRate object."
::= { dsmonPdistTopNEntry 4 }
dsmonPdistTopNRateOvfl OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The most significant 32 bits of the associated
dsmonPdistTopNHCRate object.
If the associated dsmonPdistTopNControlRateBase is equal to
'dsmonPdistTopNHCPkts' or 'dsmonPdistTopNHCOctets', then
this object will contain the upper 32 bits of the associated
dsmonPdistTopNHCRate object.
If the associated dsmonPdistTopNControlRateBase is equal to
'dsmonPdistTopNPkts' or 'dsmonPdistTopNOctets', then this
object will contain the value zero.
The agent MAY choose not to instantiate this object if High
Capacity RMON collection is not supported."
::= { dsmonPdistTopNEntry 5 }
Expires May 20, 2001 [Page 49]
Internet Draft DSMON MIB November 2000
dsmonPdistTopNHCRate OBJECT-TYPE
SYNTAX CounterBasedGauge64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of change in the selected variable during this
sampling interval. The selected variable is this protocol's
instance of the object selected by
dsmonPdistTopNControlRateBase.
If the associated dsmonPdistTopNControlRateBase is equal to
'dsmonPdistTopNPkts' or 'dsmonPdistTopNOctets', then this
object will contain the value zero, and the associated
dsmonPdistTopNRate object will contain the change in the
selected variable during the sampling interval.
The agent MAY choose not to instantiate this object if High
Capacity RMON collection is not supported."
::= { dsmonPdistTopNEntry 6 }
-- ***********************************************************
-- * *
-- * P E R - H O S T C O L L E C T I O N S *
-- * *
-- ***********************************************************
--
-- IP Host Statistics Control Table
--
dsmonHostControlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonHostControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Controls setup of per aggregation group, per IP host
distribution statistics."
::= { dsmonHostObjects 1 }
dsmonHostControlEntry OBJECT-TYPE
SYNTAX DsmonHostControlEntry
MAX-ACCESS not-accessible
STATUS current
Expires May 20, 2001 [Page 50]
Internet Draft DSMON MIB November 2000
DESCRIPTION
"A conceptual row in the dsmonHostControlTable.
Entries are created and deleted from this table by
management action only, using the dsmonHostControlStatus
RowStatus object.
Activation of a control row in this table will cause an
associated dsmonHostTable to be created and maintained by
the agent."
INDEX { dsmonHostControlIndex }
::= { dsmonHostControlTable 1 }
DsmonHostControlEntry ::= SEQUENCE {
dsmonHostControlIndex Integer32,
dsmonHostControlDataSource DataSource,
dsmonHostControlAggProfile AggProfileIndex,
dsmonHostControlMaxDesiredEntries Integer32,
dsmonHostControlIPv4PrefixLen Integer32,
dsmonHostControlIPv6PrefixLen Integer32,
dsmonHostControlDroppedFrames Counter32,
dsmonHostControlInserts Counter32,
dsmonHostControlDeletes Counter32,
dsmonHostControlCreateTime LastCreateTime,
dsmonHostControlOwner OwnerString,
dsmonHostControlStatus RowStatus
}
dsmonHostControlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary and unique index for this
dsmonHostControlEntry."
::= { dsmonHostControlEntry 1 }
dsmonHostControlDataSource OBJECT-TYPE
SYNTAX DataSource
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The source of data for the associated dsmonHostTable.
Note that only packets that contain a network protocol
Expires May 20, 2001 [Page 51]
Internet Draft DSMON MIB November 2000
encapsulation which contains a DS field [RFC2474] will be
counted in this table.
This object MUST NOT be modified if the associated
dsmonHostControlStatus object is equal to active(1)."
::= { dsmonHostControlEntry 2 }
dsmonHostControlAggProfile OBJECT-TYPE
SYNTAX AggProfileIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The dsmonAggControlIndex value identifying the aggregation
profile which should be used on behalf of this
dsmonHostControlEntry.
The associated dsmonAggControlEntry and
dsmonAggProfileEntries, identified by the same
dsmonAggControlIndex index value, MUST be active in order
for this entry to remain active. It is possible for the
aggregation configuration to change from a valid to invalid
state for this dsmonHost collection. In this case, the
associated dsmonHostControlStatus object will be changed to
the 'notReady' state, and data collection will not occur on
behalf of this control entry.
Note that an agent MAY choose to limit the actual number of
aggregation profiles which may be applied to a particular
data source.
This object MUST NOT be modified if the associated
dsmonHostControlStatus object is equal to active(1)."
::= { dsmonHostControlEntry 3 }
dsmonHostControlMaxDesiredEntries OBJECT-TYPE
SYNTAX Integer32 (-1 | 1..2147483647)
UNITS "table entries"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of entries that are desired in the
dsmonHostTable on behalf of this control entry. The probe
will not create more than this number of associated entries
in the table, but MAY choose to create fewer entries in this
table for any reason including the lack of resources.
Expires May 20, 2001 [Page 52]
Internet Draft DSMON MIB November 2000
If this value is set to -1, the probe MAY create any number
of entries in this table.
This object MUST NOT be modified if the associated
dsmonHostControlStatus object is equal to active(1)."
::= { dsmonHostControlEntry 4 }
dsmonHostControlIPv4PrefixLen OBJECT-TYPE
SYNTAX Integer32 (8..32)
UNITS "bits"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of 'leftmost' contiguous bits in the host
address field for encapsulations of IPv4, that should be
maintained in this collection. This object controls how the
dsmonHostAddress object is derived for packets which contain
an encapsulation of IPv4.
If this object has a value less than 32, then 'm' rightmost
bits, where 'm' is equal to '32 -
dsmonHostControlIPv4PrefixLen', will be cleared to zero for
counting purposes only. The 'leftmost' bit is the most
significant bit of the first network-byte-order octet of the
address.
If this object is equal to 32, then no bits are cleared in
each dsmonHostAddress field.
This object MUST NOT be modified if the associated
dsmonHostControlStatus object is equal to active(1)."
DEFVAL { 32 }
::= { dsmonHostControlEntry 5 }
dsmonHostControlIPv6PrefixLen OBJECT-TYPE
SYNTAX Integer32 (8..128)
UNITS "bits"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of 'leftmost' contiguous bits in the host
address field for encapsulations of IPv6, that should be
maintained in this collection. This object controls how the
dsmonHostAddress object is derived for packets which contain
an encapsulation of IPv6.
Expires May 20, 2001 [Page 53]
Internet Draft DSMON MIB November 2000
If this object has a value less than 128, then 'm' rightmost
bits, where 'm' is equal to '128 -
dsmonHostControlIPv6PrefixLen', will be cleared to zero for
counting purposes only. The 'leftmost' bit is the most
significant bit of the first network-byte-order octet of the
address.
If this object is equal to 128, then no bits are cleared in
each dsmonHostAddress field.
This object MUST NOT be modified if the associated
dsmonHostControlStatus object is equal to active(1)."
DEFVAL { 128 }
::= { dsmonHostControlEntry 6 }
dsmonHostControlDroppedFrames OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames which were received by the probe
and therefore not accounted for in the *StatsDropEvents, but
for which the probe chose not to count for the associated
dsmonHost entries for whatever reason. Most often, this
event occurs when the probe is out of some resources and
decides to shed load from this collection.
This count does not include packets that were not counted
because they had MAC-layer errors.
Note that if the dsmonHostTable is inactive because no
appropriate protocols are enabled in the protocol directory,
this value SHOULD be 0.
Note that, unlike the dropEvents counter, this number is the
exact number of frames dropped."
::= { dsmonHostControlEntry 7 }
dsmonHostControlInserts OBJECT-TYPE
SYNTAX Counter32
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Expires May 20, 2001 [Page 54]
Internet Draft DSMON MIB November 2000
"The number of times a dsmonHost entry has been inserted
into the dsmonHost table. If an entry is inserted, then
deleted, and then inserted, this counter will be incremented
by 2.
To allow for efficient implementation strategies, agents MAY
delay updating this object for short periods of time. For
example, an implementation strategy may allow internal data
structures to differ from those visible via SNMP for short
periods of time. This counter may reflect the internal data
structures for those short periods of time.
Note that the table size can be determined by subtracting
dsmonHostControlDeletes from dsmonHostControlInserts."
::= { dsmonHostControlEntry 8 }
dsmonHostControlDeletes OBJECT-TYPE
SYNTAX Counter32
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a dsmonHost entry has been deleted from
the dsmonHost table (for any reason). If an entry is
deleted, then inserted, and then deleted, this counter will
be incremented by 2.
To allow for efficient implementation strategies, agents MAY
delay updating this object for short periods of time. For
example, an implementation strategy may allow internal data
structures to differ from those visible via SNMP for short
periods of time. This counter may reflect the internal data
structures for those short periods of time.
Note that the table size can be determined by subtracting
dsmonHostControlDeletes from dsmonHostControlInserts."
::= { dsmonHostControlEntry 9 }
dsmonHostControlCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this control entry was last
activated. This can be used by the management station to
Expires May 20, 2001 [Page 55]
Internet Draft DSMON MIB November 2000
detect if the table has been deleted and recreated between
polls."
::= { dsmonHostControlEntry 10 }
dsmonHostControlOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonHostControlEntry 11 }
dsmonHostControlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this dsmonHostControlEntry.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonHostTable shall be deleted."
::= { dsmonHostControlEntry 12 }
--
-- IP Host Statistics Table
--
dsmonHostTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonHostEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A collection of statistics for particular network
addresses, which contain a DS field, and that has been
discovered on a particular dataSource.
The probe will add to this table all network addresses seen
as the source or destination address in all packets with no
MAC errors, and will increment octet and packet counts in
the table for all packets with no MAC errors.
Expires May 20, 2001 [Page 56]
Internet Draft DSMON MIB November 2000
If the dsmonAggControlLocked object is equal to 'false',
then all entries in this table will be deleted, and the
agent will not process packets on behalf of any
dsmonHostControlEntry."
::= { dsmonHostObjects 2 }
dsmonHostEntry OBJECT-TYPE
SYNTAX DsmonHostEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of information on Differentiated Services DSCP
usage, containing packet and octet counters for each
aggregation group index configured for collection per host
address, as identified in the dsmonAggProfileTable.
The dsmonHostControlIndex value in the index identifies the
dsmonHostControlEntry on whose behalf this entry was
created.
The protocolDirLocalIndex value in the index identifies the
specific network layer protocol encapsulation associated
with each entry, and the network protocol type of the
dsmonHostAddress object. It MUST identify a
protocolDirEntry which contains a DS field (e.g., IPv4 or
IPv6). If a protocol encapsulation with multiple network
layers is specified, then associated entries in this table
refer to the innermost network protocol layer.
The dsmonAggGroupIndex value in the index is determined by
examining the DSCP value in each monitored packet, and the
dsmonAggProfileTable entry configured for that value.
An example of the indexing of this entry is
dsmonHostOutPkts.1.27273.3.200.4.171.69.120.0"
INDEX { dsmonHostControlIndex,
dsmonHostTimeMark,
dsmonAggGroupIndex,
protocolDirLocalIndex,
dsmonHostAddress }
::= { dsmonHostTable 1 }
DsmonHostEntry ::= SEQUENCE {
dsmonHostTimeMark TimeFilter,
dsmonHostAddress OCTET STRING,
Expires May 20, 2001 [Page 57]
Internet Draft DSMON MIB November 2000
dsmonHostInPkts ZeroBasedCounter32,
dsmonHostInOctets ZeroBasedCounter32,
dsmonHostInOvflPkts ZeroBasedCounter32,
dsmonHostInOvflOctets ZeroBasedCounter32,
dsmonHostInHCPkts ZeroBasedCounter64,
dsmonHostInHCOctets ZeroBasedCounter64,
dsmonHostOutPkts ZeroBasedCounter32,
dsmonHostOutOctets ZeroBasedCounter32,
dsmonHostOutOvflPkts ZeroBasedCounter32,
dsmonHostOutOvflOctets ZeroBasedCounter32,
dsmonHostOutHCPkts ZeroBasedCounter64,
dsmonHostOutHCOctets ZeroBasedCounter64,
dsmonHostCreateTime LastCreateTime
}
dsmonHostTimeMark OBJECT-TYPE
SYNTAX TimeFilter
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Time Filter index for this table. This object may be
used by a management station to retrieve only rows which
have been created or modified since a particular time. Note
that the current value for a row are always returned and the
TimeFilter is not a historical data archiving mechanism.
Refer to RFC 2021 [RFC2021] for a detailed description of
TimeFilter operation."
::= { dsmonHostEntry 1 }
dsmonHostAddress OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The network address for this dsmonHostEntry.
This object is encoded according to the protocol type
indicated by the protocolDirLocalIndex value in the index.
In addition, this object may have some 'rightmost' bits
cleared to zero for counting purposes, as indicated by the
associated dsmonHostControlIPv4PrefixLen or
dsmonHostControlIPv6PrefixLen objects."
::= { dsmonHostEntry 2 }
Expires May 20, 2001 [Page 58]
Internet Draft DSMON MIB November 2000
dsmonHostInPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets without errors, using one of the DSCP
values in the indicated aggregation group, and transmitted
to this address, since this entry was added to the
dsmonHostTable. Note that this is the number of link-layer
packets, so if a single network-layer packet is fragmented
into several link-layer frames, this counter is incremented
several times."
::= { dsmonHostEntry 3 }
dsmonHostInOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets in all packets, transmitted to this
address and using one of the DSCP values in the indicated
aggregation group, since this entry was added to the
dsmonHostTable (excluding framing bits but including FCS
octets), excluding those octets in packets that contained
errors.
Note this doesn't count just those octets in the particular
protocol frames, but includes the entire packet that
contained the protocol."
::= { dsmonHostEntry 4 }
dsmonHostInOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonHostInPkts counter
has overflowed. Note that this object will only be
instantiated if the associated dsmonHostInHCPkts object is
also instantiated for a particular dataSource."
::= { dsmonHostEntry 5 }
Expires May 20, 2001 [Page 59]
Internet Draft DSMON MIB November 2000
dsmonHostInOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonHostInOctets
counter has overflowed. Note that this object will only be
instantiated if the associated dsmonHostInHCOctets object is
also instantiated for a particular dataSource."
::= { dsmonHostEntry 6 }
dsmonHostInHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonHostInPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity RMON for a particular
dataSource."
::= { dsmonHostEntry 7 }
dsmonHostInHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonHostInOctets object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity RMON for a particular
dataSource."
::= { dsmonHostEntry 8 }
dsmonHostOutPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets without errors, using one of the DSCP
Expires May 20, 2001 [Page 60]
Internet Draft DSMON MIB November 2000
values in the indicated aggregation group, and transmitted
by this address, since this entry was added to the
dsmonHostTable. Note that this is the number of link-layer
packets, so if a single network-layer packet is fragmented
into several link-layer frames, this counter is incremented
several times."
::= { dsmonHostEntry 9 }
dsmonHostOutOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets, transmitted by this address and using
one of the DSCP values in the identified aggregation group,
since this entry was added to the dsmonHostTable (excluding
framing bits but including FCS octets), excluding those
octets in packets that contained errors.
Note this doesn't count just those octets in the particular
protocol frames, but includes the entire packet that
contained the protocol."
::= { dsmonHostEntry 10 }
dsmonHostOutOvflPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "packets"
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonHostOutPkts counter
has overflowed. Note that this object will only be
instantiated if the associated dsmonHostOutHCPkts object is
also instantiated for a particular dataSource."
::= { dsmonHostEntry 11 }
dsmonHostOutOvflOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "octets"
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times the associated dsmonHostOutOctets
counter has overflowed. Note that this object will only be
Expires May 20, 2001 [Page 61]
Internet Draft DSMON MIB November 2000
instantiated if the associated dsmonHostOutHCOctets object
is also instantiated for a particular dataSource."
::= { dsmonHostEntry 12 }
dsmonHostOutHCPkts OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonHostOutPkts object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity RMON for a particular
dataSource."
::= { dsmonHostEntry 13 }
dsmonHostOutHCOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 64-bit version of the dsmonHostOutOctets object.
Note that this object will only be instantiated if the RMON
agent supports High Capacity RMON for a particular
dataSource."
::= { dsmonHostEntry 14 }
dsmonHostCreateTime OBJECT-TYPE
SYNTAX LastCreateTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this dsmonHost entry was last
instantiated by the agent. This can be used by the
management station to ensure that the entry has not been
deleted and recreated between polls."
::= { dsmonHostEntry 15 }
--
-- Per-Protocol Per-Host Statistics TopN Control Table
--
Expires May 20, 2001 [Page 62]
Internet Draft DSMON MIB November 2000
dsmonHostTopNControlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonHostTopNControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of parameters that control the creation of a report
of the top N dsmonHost entries according to a selected
metric."
::= { dsmonHostObjects 3 }
dsmonHostTopNControlEntry OBJECT-TYPE
SYNTAX DsmonHostTopNControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonHostTopNControlTable.
Entries are created and deleted from this table by
management action only, using the dsmonHostTopNControlStatus
RowStatus object.
Activation of a control row in this table will cause an
associated dsmonHostTopNTable to be created and maintained
by the agent."
INDEX { dsmonHostTopNControlIndex }
::= { dsmonHostTopNControlTable 1 }
DsmonHostTopNControlEntry ::= SEQUENCE {
dsmonHostTopNControlIndex Integer32,
dsmonHostTopNControlHostIndex Integer32,
dsmonHostTopNControlRateBase INTEGER,
dsmonHostTopNControlTimeRemaining Integer32,
dsmonHostTopNControlGeneratedReports Counter32,
dsmonHostTopNControlDuration Integer32,
dsmonHostTopNControlRequestedSize Integer32,
dsmonHostTopNControlGrantedSize Integer32,
dsmonHostTopNControlStartTime TimeStamp,
dsmonHostTopNControlOwner OwnerString,
dsmonHostTopNControlStatus RowStatus
}
dsmonHostTopNControlIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
Expires May 20, 2001 [Page 63]
Internet Draft DSMON MIB November 2000
DESCRIPTION
"An index that uniquely identifies an entry in the
dsmonHostTopNControlTable. Each such entry defines one Top
N report prepared for one RMON dataSource."
::= { dsmonHostTopNControlEntry 1 }
dsmonHostTopNControlHostIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The dsmonHostTable for which a top N report will be
prepared on behalf of this entry. The dsmonHostTable is
identified by the value of the dsmonHostControlIndex for
that table - that value is used here to identify the
particular table.
This object MUST NOT be modified if the associated
dsmonHostTopNControlStatus object is equal to active(1)."
::= { dsmonHostTopNControlEntry 2 }
dsmonHostTopNControlRateBase OBJECT-TYPE
SYNTAX INTEGER {
dsmonHostTopNInPkts(1),
dsmonHostTopNInOctets(2),
dsmonHostTopNOutPkts(3),
dsmonHostTopNOutOctets(4),
dsmonHostTopNTotalPkts(5),
dsmonHostTopNTotalOctets(6),
dsmonHostTopNInHCPkts(7),
dsmonHostTopNInHCOctets(8),
dsmonHostTopNOutHCPkts(9),
dsmonHostTopNOutHCOctets(10),
dsmonHostTopNTotalHCPkts(11),
dsmonHostTopNTotalHCOctets(12),
dsmonHostTopNObsolete(13)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The variable(s) for each dsmonHost that the
dsmonHostTopNRate and dsmonHostTopNHCRate variables are
based upon. Each dsmonHostTopN report generated on behalf
of this control entry will be ranked in descending order,
based on the associated dsmonHostTable counter(s),
Expires May 20, 2001 [Page 64]
Internet Draft DSMON MIB November 2000
identified by this object.
The following table identifies the dsmonHostTable counters
associated with each enumeration:
Enumeration RateBase MIB Objects
----------- --------------------
dsmonHostTopNInPkts dsmonHostInPkts
dsmonHostTopNInOctets dsmonHostInOctets
dsmonHostTopNOutPkts dsmonHostOutPkts
dsmonHostTopNOutOctets dsmonHostOutOctets
dsmonHostTopNTotalPkts dsmonHostInPkts +
dsmonHostOutPkts
dsmonHostTopNTotalOctets dsmonHostInOctets +
dsmonHostOutOctets
dsmonHostTopNInHCPkts dsmonHostInHCPkts
dsmonHostTopNInHCOctets dsmonHostInHCOctets
dsmonHostTopNOutHCPkts dsmonHostOutHCPkts
dsmonHostTopNOutHCOctets dsmonHostOutHCPkts
dsmonHostTopNTotalHCPkts dsmonHostInHCPkts +
dsmonHostOutHCPkts
dsmonHostTopNTotalHCOctets dsmonHostInHCOctets +
dsmonHostOutHCOctets
dsmonHostTopNObsolete <not specified here>
The following enumerations are only available if the agent
supports High Capacity RMON collection:
dsmonHostTopNInHCPkts
dsmonHostTopNInHCOctets
dsmonHostTopNOutHCPkts
dsmonHostTopNOutHCOctets
dsmonHostTopNTotalHCPkts
dsmonHostTopNTotalHCOctets
It is an implementation-specific matter whether an agent can
detect an overflow condition resulting from the addition of
two counter delta values for the following enumerations:
dsmonHostTopNTotalPkts
dsmonHostTopNTotalOctets
dsmonHostTopNTotalHCPkts
dsmonHostTopNTotalHCOctets
In the event such an overflow condition can be detected by
Expires May 20, 2001 [Page 65]
Internet Draft DSMON MIB November 2000
the agent, the associated dsmonHostTopNRate,
dsmonHostTopNRateOvfl, and/or dsmonHostTopNHCRate objects
should be set to their maximum value.
This object SHOULD be set to the value
'dsmonHostTopNObsolete(13)', if an updated version of this
object has been created in another MIB module, and this rate
base MIB object is no longer used.
This object MUST NOT be modified if the associated
dsmonHostTopNControlStatus object is equal to active(1)."
::= { dsmonHostTopNControlEntry 3 }
dsmonHostTopNControlTimeRemaining OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds left in the report currently being
collected. When this object is modified by the management
station, a new collection is started, possibly aborting a
currently running report. The new value is used as the
requested duration of this report, and is immediately loaded
into the associated dsmonHostTopNControlDuration object.
When the report finishes, the probe will automatically start
another collection with the same initial value of
dsmonHostTopNControlTimeRemaining. Thus the management
station may simply read the resulting reports repeatedly,
checking the startTime and duration each time to ensure that
a report was not missed or that the report parameters were
not changed.
While the value of this object is non-zero, it decrements by
one per second until it reaches zero. At the time that this
object decrements to zero, the report is made accessible in
the dsmonHostTopNTable, overwriting any report that may be
there.
When this object is modified by the management station, any
associated entries in the dsmonHostTopNTable shall be
deleted."
DEFVAL { 1800 }
::= { dsmonHostTopNControlEntry 4 }
Expires May 20, 2001 [Page 66]
Internet Draft DSMON MIB November 2000
dsmonHostTopNControlGeneratedReports OBJECT-TYPE
SYNTAX Counter32
UNITS "reports"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of reports that have been generated by this
entry."
::= { dsmonHostTopNControlEntry 5 }
dsmonHostTopNControlDuration OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of seconds that this report has collected during
the last sampling interval.
When the associated dsmonHostTopNControlTimeRemaining object
is set, this object shall be set by the probe to the same
value and shall not be modified until the next time the
dsmonHostTopNControlTimeRemaining is set.
This value shall be zero if no reports have been requested
for this dsmonHostTopNControlEntry."
::= { dsmonHostTopNControlEntry 6 }
dsmonHostTopNControlRequestedSize OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
UNITS "table entries"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of dsmonHost entries requested for this
report.
When this object is created or modified, the probe SHOULD
set dsmonHostTopNControlGrantedSize as closely to this
object as is possible for the particular probe
implementation and available resources."
DEFVAL { 150 }
::= { dsmonHostTopNControlEntry 7 }
dsmonHostTopNControlGrantedSize OBJECT-TYPE
Expires May 20, 2001 [Page 67]
Internet Draft DSMON MIB November 2000
SYNTAX Integer32 (0..2147483647)
UNITS "table entries"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of dsmonHost entries in this report.
When the associated dsmonHostTopNControlRequestedSize object
is created or modified, the probe SHOULD set this object as
closely to the requested value as is possible for the
particular implementation and available resources. The probe
MUST NOT lower this value except as a result of a set to the
associated dsmonHostTopNControlRequestedSize object.
When the associated dsmonHostTopNControlRequestedSize object
is created or modified, the probe SHOULD set this object as
closely to the requested value as is possible for the
particular implementation and available resources. The probe
MUST NOT lower this value except as a result of a set to the
associated dsmonHostTopNControlRequestedSize object.
Protocol entries with the highest value of dsmonHostTopNRate
or dsmonHostTopNHCRate (depending on the value of the
associated dsmonHostTopNControlRateBase object) shall be
placed in this table in decreasing order of this rate until
there is no more room or until there are no more dsmonHost
entries."
::= { dsmonHostTopNControlEntry 8 }
dsmonHostTopNControlStartTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when this top N report was last
started. In other words, this is the time that the
associated dsmonHostTopNControlTimeRemaining object was
modified to start the requested report or the time the
report was last automatically (re)started.
This object may be used by the management station to
determine if a report was missed or not."
::= { dsmonHostTopNControlEntry 9 }
dsmonHostTopNControlOwner OBJECT-TYPE
Expires May 20, 2001 [Page 68]
Internet Draft DSMON MIB November 2000
SYNTAX OwnerString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entity that configured this entry and is therefore
using the resources assigned to it."
::= { dsmonHostTopNControlEntry 10 }
dsmonHostTopNControlStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this dsmonHostTopNControlEntry.
An entry MUST NOT exist in the active state unless all
objects in the entry have an appropriate value.
If this object is not equal to active(1), all associated
entries in the dsmonHostTopNTable shall be deleted by the
agent."
::= { dsmonHostTopNControlEntry 11 }
--
-- dsmonHost TopN Table
--
dsmonHostTopNTable OBJECT-TYPE
SYNTAX SEQUENCE OF DsmonHostTopNEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A set of statistics for those dsmonHost entries that have
counted the highest number of octets or packets.
If the dsmonAggControlLocked object is equal to 'false',
then all entries in this table SHALL be deleted, and the
agent will not process TopN reports on behalf of any
dsmonHostTopNControlEntry.
When the dsmonAggControlLocked object is set to 'true', then
particular reports SHOULD be restarted from the beginning,
on behalf of all active rows in the
dsmonHostTopNControlTable.
Expires May 20, 2001 [Page 69]
Internet Draft DSMON MIB November 2000
Note that dsmonHost entries which did not increment at all
during the report interval SHOULD NOT be included in
dsmonHostTopN reports."
::= { dsmonHostObjects 4 }
dsmonHostTopNEntry OBJECT-TYPE
SYNTAX DsmonHostTopNEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in the dsmonHostTopNTable.
The dsmonHostTopNControlIndex value in the index identifies
the dsmonHostTopNControlEntry on whose behalf this entry was
created."
INDEX { dsmonHostTopNControlIndex, dsmonHostTopNIndex }
::= { dsmonHostTopNTable 1 }
DsmonHostTopNEntry ::= SEQUENCE {
dsmonHostTopNIndex Integer32,
dsmonHostTopNPDLocalIndex Integer32,
dsmonHostTopNAddress OCTET STRING,
dsmonHostTopNAggGroup AggGroupIndex,
dsmonHostTopNRate Gauge32,
dsmonHostTopNRateOvfl Gauge32,
dsmonHostTopNHCRate CounterBasedGauge64
}
dsmonHostTopNIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
dsmonHostTopNTable among those in the same report. This
index is between 1 and N, where N is the number of entries
in this report."
::= { dsmonHostTopNEntry 1 }
dsmonHostTopNPDLocalIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The protocolDirLocalIndex value which identifies the
Expires May 20, 2001 [Page 70]
Internet Draft DSMON MIB November 2000
protocol associated with the dsmonHostTopNAddress object in
this entry.
If the protocolDirEntry associated with the
protocolDirLocalIndex with the same value as this object is
de-activated or deleted, then the agent MUST delete this
dsmonHostTopN entry."
::= { dsmonHostTopNEntry 2 }
dsmonHostTopNAddress OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The dsmonHostAddress value for the network host identified
in this entry. The associated dsmonHostTopNPDLocalIndex
object identifies the network protocol type and the encoding
rules for this object."
::= { dsmonHostTopNEntry 3 }
dsmonHostTopNAggGroup OBJECT-TYPE
SYNTAX AggGroupIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The aggregation group index value associated with host
identified in this entry."
::= { dsmonHostTopNEntry 4 }
dsmonHostTopNRate OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of change in the selected variable during this
sampling interval. The selected variable is this host's
instance of the object selected by
dsmonHostTopNControlRateBase.
If the associated dsmonHostTopNControlRateBase indicates a
High Capacity RMON enumeration, (e.g.
'dsmonHostTopNInHCPkts'), then this object will contain the
the least significant 32 bits of the associated
dsmonHostTopNHCRate object."
::= { dsmonHostTopNEntry 5 }
Expires May 20, 2001 [Page 71]
Internet Draft DSMON MIB November 2000
dsmonHostTopNRateOvfl OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The most significant 32 bits of the associated
dsmonHostTopNHCRate object.
If the associated dsmonHostTopNControlRateBase is equal to
any of the High Capacity RMON enumerations (e.g.
'dsmonHostTopNInHCPkts'), then this object will contain the
upper 32 bits of the associated dsmonHostTopNHCRate object.
If the associated dsmonHostTopNControlRateBase is not equal
to any of High Capacity RMON enumerations, then this object
will contain the value zero.
The agent MAY choose not to instantiate this object if High
Capacity RMON collection is not supported."
::= { dsmonHostTopNEntry 6 }
dsmonHostTopNHCRate OBJECT-TYPE
SYNTAX CounterBasedGauge64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of change in the selected variable during this
sampling interval. The selected variable is this host's
instance of the object selected by
dsmonHostTopNControlRateBase.
If the associated dsmonHostTopNControlRateBase is not equal
to any of the High Capacity RMON enumerations (e.g.,
'dsmonHostTopNInPkts'), then this object will contain the
value zero, and the associated dsmonHostTopNRate object will
contain the change in the selected variable during the
sampling interval.
The agent MAY choose not to instantiate this object if High
Capacity RMON collection is not supported."
::= { dsmonHostTopNEntry 7 }
--
-- Notifications Section
Expires May 20, 2001 [Page 72]
Internet Draft DSMON MIB November 2000
-- (none defined)
--
--
-- Conformance Section
--
dsmonCompliances OBJECT IDENTIFIER ::= { dsmonConformance 1 }
dsmonGroups OBJECT IDENTIFIER ::= { dsmonConformance 2 }
dsmonCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Describes the requirements for conformance to the
Differentiated Services Monitoring MIB."
MODULE -- this module
MANDATORY-GROUPS { dsmonAggControlGroup, dsmonStatsGroup }
GROUP dsmonStatsHCGroup
DESCRIPTION
"The dsmonStatsHCGroup is mandatory for systems which
implement High Capacity RMON monitoring."
::= { dsmonCompliances 1 }
dsmonAggControlGroup OBJECT-GROUP
OBJECTS {
dsmonMaxAggGroups,
dsmonAggControlLocked,
dsmonAggControlChanges,
dsmonAggControlLastChangeTime,
dsmonAggControlDescr,
dsmonAggControlOwner,
dsmonAggControlStatus,
dsmonAggGroupIndex,
dsmonAggGroupDescr,
dsmonAggGroupStatus
}
STATUS current
DESCRIPTION
"A collection of objects used to configure and manage
aggregation groups for DSMON collection purposes."
::= { dsmonGroups 1 }
dsmonStatsGroup OBJECT-GROUP
OBJECTS {
dsmonStatsControlDataSource,
Expires May 20, 2001 [Page 73]
Internet Draft DSMON MIB November 2000
dsmonStatsControlAggProfile,
dsmonStatsControlDroppedFrames,
dsmonStatsControlCreateTime,
dsmonStatsControlOwner,
dsmonStatsControlStatus,
dsmonStatsInPkts,
dsmonStatsInOctets,
dsmonStatsOutPkts,
dsmonStatsOutOctets
}
STATUS current
DESCRIPTION
"A collection of objects providing per DSCP statistics."
::= { dsmonGroups 2 }
dsmonStatsOvflGroup OBJECT-GROUP
OBJECTS {
dsmonStatsInOvflPkts,
dsmonStatsInOvflOctets,
dsmonStatsOutOvflPkts,
dsmonStatsOutOvflOctets
}
STATUS deprecated
DESCRIPTION
"A collection of objects providing per-DSCP overflow
counters for systems with high capacity data sources, but
without support for the Counter64 data type."
::= { dsmonGroups 3 }
dsmonStatsHCGroup OBJECT-GROUP
OBJECTS {
dsmonStatsInHCPkts,
dsmonStatsInHCOctets,
dsmonStatsOutHCPkts,
dsmonStatsOutHCOctets
}
STATUS current
DESCRIPTION
"A collection of objects providing per DSCP statistics for
high capacity data sources."
::= { dsmonGroups 4 }
dsmonPdistGroup OBJECT-GROUP
OBJECTS {
dsmonPdistControlDataSource,
Expires May 20, 2001 [Page 74]
Internet Draft DSMON MIB November 2000
dsmonPdistControlAggProfile,
dsmonPdistControlMaxDesiredEntries,
dsmonPdistControlDroppedFrames,
dsmonPdistControlInserts,
dsmonPdistControlDeletes,
dsmonPdistControlCreateTime,
dsmonPdistControlOwner,
dsmonPdistControlStatus,
dsmonPdistStatsPkts,
dsmonPdistStatsOctets,
dsmonPdistStatsCreateTime,
dsmonPdistTopNControlPdistIndex,
dsmonPdistTopNControlRateBase,
dsmonPdistTopNControlTimeRemaining,
dsmonPdistTopNControlGeneratedReports,
dsmonPdistTopNControlDuration,
dsmonPdistTopNControlRequestedSize,
dsmonPdistTopNControlGrantedSize,
dsmonPdistTopNControlStartTime,
dsmonPdistTopNControlOwner,
dsmonPdistTopNControlStatus,
dsmonPdistTopNPDLocalIndex,
dsmonPdistTopNAggGroup,
dsmonPdistTopNRate
}
STATUS current
DESCRIPTION
"A collection of objects providing per protocol DSCP
monitoring extensions to the RMON-2 MIB."
::= { dsmonGroups 5 }
dsmonPdistOvflGroup OBJECT-GROUP
OBJECTS {
dsmonPdistStatsOvflPkts,
dsmonPdistStatsOvflOctets,
dsmonPdistTopNRateOvfl
}
STATUS deprecated
DESCRIPTION
"A collection of objects providing per-protocol DSCP
overflow counters for systems with high capacity data
sources, but without support for the Counter64 data type."
::= { dsmonGroups 6 }
dsmonPdistHCGroup OBJECT-GROUP
Expires May 20, 2001 [Page 75]
Internet Draft DSMON MIB November 2000
OBJECTS {
dsmonPdistStatsHCPkts,
dsmonPdistStatsHCOctets,
dsmonPdistTopNHCRate
}
STATUS current
DESCRIPTION
"A collection of objects providing per protocol DSCP
monitoring extensions to the RMON-2 MIB for High Capacicy
networks."
::= { dsmonGroups 7 }
dsmonHostGroup OBJECT-GROUP
OBJECTS {
dsmonHostControlDataSource,
dsmonHostControlAggProfile,
dsmonHostControlMaxDesiredEntries,
dsmonHostControlIPv4PrefixLen,
dsmonHostControlIPv6PrefixLen,
dsmonHostControlDroppedFrames,
dsmonHostControlInserts,
dsmonHostControlDeletes,
dsmonHostControlCreateTime,
dsmonHostControlOwner,
dsmonHostControlStatus,
dsmonHostInPkts,
dsmonHostInOctets,
dsmonHostOutPkts,
dsmonHostOutOctets,
dsmonHostCreateTime,
dsmonHostTopNControlHostIndex,
dsmonHostTopNControlRateBase,
dsmonHostTopNControlTimeRemaining,
dsmonHostTopNControlGeneratedReports,
dsmonHostTopNControlDuration,
dsmonHostTopNControlRequestedSize,
dsmonHostTopNControlGrantedSize,
dsmonHostTopNControlStartTime,
dsmonHostTopNControlOwner,
dsmonHostTopNControlStatus,
dsmonHostTopNPDLocalIndex,
dsmonHostTopNAddress,
dsmonHostTopNAggGroup,
dsmonHostTopNRate
}
Expires May 20, 2001 [Page 76]
Internet Draft DSMON MIB November 2000
STATUS current
DESCRIPTION
"A collection of objects providing per IP Host monitoring
functions."
::= { dsmonGroups 8 }
dsmonHostOvflGroup OBJECT-GROUP
OBJECTS {
dsmonHostInOvflPkts,
dsmonHostInOvflOctets,
dsmonHostOutOvflPkts,
dsmonHostOutOvflOctets,
dsmonHostTopNRateOvfl
}
STATUS deprecated
DESCRIPTION
"A collection of objects providing per IP host DSCP overflow
counters for systems with high capacity data sources, but
without support for the Counter64 data type."
::= { dsmonGroups 9 }
dsmonHostHCGroup OBJECT-GROUP
OBJECTS {
dsmonHostInHCPkts,
dsmonHostInHCOctets,
dsmonHostOutHCPkts,
dsmonHostOutHCOctets,
dsmonHostTopNHCRate
}
STATUS current
DESCRIPTION
"A collection of objects providing per IP Host monitoring
functions for High Capacity networks."
::= { dsmonGroups 10 }
END
Expires May 20, 2001 [Page 77]
Internet Draft DSMON MIB November 2000
8. Aggregation Configuration Usage Examples
This section contains an example of the steps that may be followed by a
management station to configure the objects in the dsmonAggControlGroup.
A note about these examples:
- they do not define a standard
- an agent is not obligated to support them
- a management application is not constrained by them
- the SET(object = value [, ...]) notation is
only conceptual, and is not meant to represent an actual SNMP Set
PDU.
8.1. Step 1: Unlock the Aggregation Configuration
Before any write operations to the tabular objects in this group can be
made, the aggregation configuration must be unlocked, by setting the
dsmonAggControlLocked scalar to false:
SET(dsmonAggControlLocked.0 = false(2));
8.2. Step 2: Check the Maximum number of Aggregation Groups
Make sure the desired aggregation groups have a chance of being
configured on the agent.
maxGroups = GET(dsmonAggMaxAggGroups.0);
For this example, maxGroups is greater or equal to 64.
8.3. Step 3: Check if the aggregation profiles already exist
Make sure the desired aggregation profiles have not already been
configured, or perhaps recreated after an agent restart. The following
example is oversimplified, in that the entire aggregation configuration
should actually be verified.
profile1Descr = GET(dsmonAggControlDescr.1);
profile1Owner = GET(dsmonAggControlOwner.1);
profile1Status = GET(dsmonAggControlStatus.1);
Expires May 20, 2001 [Page 78]
Internet Draft DSMON MIB November 2000
For this example, none of the aggregation profiles already exist.
8.4. Step 4: Create the Aggregation Control Entries
The management station should create one entry in the
dsmonAggControlTable for each aggregation profile to be configured on
the agent.
Steps 4, 5, and 6 are repeated for each aggregation profile to be
configured on the agent. There are 4 example aggregation profiles shown
in each of these steps.
Example 1: no aggregation at all.
SET(dsmonAggControlStatus.1 = createAndGo(4),
dsmonAggControlOwner.1 = "Example App 1",
dsmonAggControlDescr.1 = "No Aggregation");
Example 2: a collection of DIFFSERV PHBs.
SET(dsmonAggControlStatus.2 = createAndGo(4),
dsmonAggControlOwner.2 = "Example App 2",
dsmonAggControlDescr.2 = "June 2000 DIFFSERV PHBs");
Example 3: an aggregated collection of DIFFSERV PHBs.
SET(dsmonAggControlStatus.3 = createAndGo(4),
dsmonAggControlOwner.3 = "Example App 3",
dsmonAggControlDescr.3 = "Limited June 2000 PHBs");
Example 4: an initial configuration
SET(dsmonAggControlStatus.4 = createAndGo(4),
dsmonAggControlOwner.4 = "monitor",
dsmonAggControlDescr.4 = "Initial Configuration");
8.5. Step 5: Create the Aggregation Group Descriptions
The dsmonAggGroupEntries can be created at any time. The management
station should create one entry for each aggregation group, for each
aggregation profile,
Example 1: no aggregation at all. One group is created for each
codepoint, for a total of 64 rows.
Expires May 20, 2001 [Page 79]
Internet Draft DSMON MIB November 2000
SET(dsmonAggGroupStatus.1.0 = createAndGo(4),
dsmonAggGroupDescr.1.0 = "DSCP 0");
SET(dsmonAggGroupStatus.1.1 = createAndGo(4),
dsmonAggGroupDescr.1.1 = "DSCP 1");
SET(dsmonAggGroupStatus.1.2 = createAndGo(4),
dsmonAggGroupDescr.1.2 = "DSCP 2");
SET(dsmonAggGroupStatus.1.3 = createAndGo(4),
dsmonAggGroupDescr.1.3 = "DSCP 3");
...
SET(dsmonAggGroupStatus.1.63 = createAndGo(4),
dsmonAggGroupDescr.1.63 = "DSCP 63");
Example 2: a collection of current DIFFSERV PHBs. One group is created
for each PHB to be monitored
SET(dsmonAggGroupStatus.2.0 = createAndGo(4),
dsmonAggGroupDescr.2.0 = "CS0");
SET(dsmonAggGroupStatus.2.1 = createAndGo(4),
dsmonAggGroupDescr.2.1 = "CS1");
SET(dsmonAggGroupStatus.2.2 = createAndGo(4),
dsmonAggGroupDescr.2.2 = "CS2");
SET(dsmonAggGroupStatus.2.3 = createAndGo(4),
dsmonAggGroupDescr.2.3 = "CS3");
SET(dsmonAggGroupStatus.2.4 = createAndGo(4),
dsmonAggGroupDescr.2.4 = "CS4");
SET(dsmonAggGroupStatus.2.5 = createAndGo(4),
dsmonAggGroupDescr.2.5 = "CS5");
SET(dsmonAggGroupStatus.2.6 = createAndGo(4),
dsmonAggGroupDescr.2.6 = "CS6");
SET(dsmonAggGroupStatus.2.7 = createAndGo(4),
dsmonAggGroupDescr.2.7 = "CS7");
SET(dsmonAggGroupStatus.2.8 = createAndGo(4),
dsmonAggGroupDescr.2.8 = "EF");
SET(dsmonAggGroupStatus.2.9 = createAndGo(4),
dsmonAggGroupDescr.2.9 = "AF11");
SET(dsmonAggGroupStatus.2.10 = createAndGo(4),
dsmonAggGroupDescr.2.10 = "AF12");
SET(dsmonAggGroupStatus.2.11 = createAndGo(4),
dsmonAggGroupDescr.2.11 = "AF13");
SET(dsmonAggGroupStatus.2.12 = createAndGo(4),
dsmonAggGroupDescr.2.12 = "AF21");
SET(dsmonAggGroupStatus.2.13 = createAndGo(4),
dsmonAggGroupDescr.2.13 = "AF22");
Expires May 20, 2001 [Page 80]
Internet Draft DSMON MIB November 2000
SET(dsmonAggGroupStatus.2.14 = createAndGo(4),
dsmonAggGroupDescr.2.14 = "AF23");
SET(dsmonAggGroupStatus.2.15 = createAndGo(4),
dsmonAggGroupDescr.2.15 = "AF31");
SET(dsmonAggGroupStatus.2.16 = createAndGo(4),
dsmonAggGroupDescr.2.16 = "AF32");
SET(dsmonAggGroupStatus.2.17 = createAndGo(4),
dsmonAggGroupDescr.2.17 = "AF33");
SET(dsmonAggGroupStatus.2.18 = createAndGo(4),
dsmonAggGroupDescr.2.18 = "AF41");
SET(dsmonAggGroupStatus.2.19 = createAndGo(4),
dsmonAggGroupDescr.2.19 = "AF42");
SET(dsmonAggGroupStatus.2.20 = createAndGo(4),
dsmonAggGroupDescr.2.20 = "AF43");
SET(dsmonAggGroupStatus.2.21 = createAndGo(4),
dsmonAggGroupDescr.2.21 = "Nonzero Default");
Example 3: an aggregated representation of current DIFFSERV PHBs. One
group is created for each aggregation to be monitored (8 rows in this
example).
SET(dsmonAggGroupStatus.3.0 = createAndGo(4),
dsmonAggGroupDescr.3.0 = "Zero CS");
SET(dsmonAggGroupStatus.3.1 = createAndGo(4),
dsmonAggGroupDescr.3.1 = "Nonzero CS");
SET(dsmonAggGroupStatus.3.2 = createAndGo(4),
dsmonAggGroupDescr.3.2 = "EF");
SET(dsmonAggGroupStatus.3.3 = createAndGo(4),
dsmonAggGroupDescr.3.3 = "AF1");
SET(dsmonAggGroupStatus.3.4 = createAndGo(4),
dsmonAggGroupDescr.3.4 = "AF2");
SET(dsmonAggGroupStatus.3.5 = createAndGo(4),
dsmonAggGroupDescr.3.5 = "AF3");
SET(dsmonAggGroupStatus.3.6 = createAndGo(4),
dsmonAggGroupDescr.3.6 = "AF4");
SET(dsmonAggGroupStatus.3.7 = createAndGo(4),
dsmonAggGroupDescr.3.7 = "Nonzero Default");
Example 4: an example initial configuration. Note that no
dsmonAggGroupEntries actually need to be created. In this example, an
entry will be created anyway.
SET(dsmonAggGroupStatus.4.0 = createAndGo(4),
dsmonAggGroupDescr.4.0 = "Initial Configuration");
Expires May 20, 2001 [Page 81]
Internet Draft DSMON MIB November 2000
8.6. Step 6: Create the Aggregation Profile Mappings
After the dsmonAggControlEntries are activated, the associated read-
write dsmonAggProfileEntries will be created. The management station
must create 64 entries in the dsmonAggProfileTable for each aggregation
profile configured in the dsmonAggControlTable.
Example 1: no aggregation at all.
SET(dsmonAggGroupIndex.1.0 = 0,
dsmonAggGroupIndex.1.1 = 1,
dsmonAggGroupIndex.1.2 = 2,
dsmonAggGroupIndex.1.3 = 3,
...
dsmonAggGroupIndex.1.63 = 63);
Example 2: a collection of current DIFFSERV PHBs.
SET(dsmonAggGroupIndex.2.0 = 0, -- CS0
dsmonAggGroupIndex.2.1 = 21, -- Nonzero Default
dsmonAggGroupIndex.2.2 = 21,
dsmonAggGroupIndex.2.3 = 21,
dsmonAggGroupIndex.2.4 = 21,
dsmonAggGroupIndex.2.5 = 21,
dsmonAggGroupIndex.2.6 = 21,
dsmonAggGroupIndex.2.7 = 21,
dsmonAggGroupIndex.2.8 = 1, -- CS1
dsmonAggGroupIndex.2.9 = 21,
dsmonAggGroupIndex.2.10 = 9, -- AF11
dsmonAggGroupIndex.2.11 = 21,
dsmonAggGroupIndex.2.12 = 10, -- AF12
dsmonAggGroupIndex.2.13 = 21,
dsmonAggGroupIndex.2.14 = 11, -- AF13
dsmonAggGroupIndex.2.15 = 21,
dsmonAggGroupIndex.2.16 = 2, -- CS2
dsmonAggGroupIndex.2.17 = 21,
dsmonAggGroupIndex.2.18 = 12, -- AF21
dsmonAggGroupIndex.2.19 = 21,
dsmonAggGroupIndex.2.20 = 13, -- AF22
dsmonAggGroupIndex.2.21 = 21,
dsmonAggGroupIndex.2.22 = 14, -- AF23
dsmonAggGroupIndex.2.23 = 21,
dsmonAggGroupIndex.2.24 = 3, -- CS3
dsmonAggGroupIndex.2.25 = 21,
dsmonAggGroupIndex.2.26 = 15, -- AF31
Expires May 20, 2001 [Page 82]
Internet Draft DSMON MIB November 2000
dsmonAggGroupIndex.2.27 = 21,
dsmonAggGroupIndex.2.28 = 16, -- AF32
dsmonAggGroupIndex.2.29 = 8, -- EF
dsmonAggGroupIndex.2.30 = 17, -- AF33
dsmonAggGroupIndex.2.31 = 21,
dsmonAggGroupIndex.2.32 = 4, -- CS4
dsmonAggGroupIndex.2.33 = 21,
dsmonAggGroupIndex.2.34 = 18, -- AF41
dsmonAggGroupIndex.2.35 = 21,
dsmonAggGroupIndex.2.36 = 19, -- AF42
dsmonAggGroupIndex.2.37 = 21,
dsmonAggGroupIndex.2.38 = 20, -- AF43
dsmonAggGroupIndex.2.39 = 21,
dsmonAggGroupIndex.2.40 = 5, -- CS5
dsmonAggGroupIndex.2.41 = 21,
dsmonAggGroupIndex.2.42 = 21,
dsmonAggGroupIndex.2.43 = 21,
dsmonAggGroupIndex.2.44 = 21,
dsmonAggGroupIndex.2.45 = 21,
dsmonAggGroupIndex.2.46 = 21,
dsmonAggGroupIndex.2.47 = 21,
dsmonAggGroupIndex.2.48 = 6, -- CS6
dsmonAggGroupIndex.2.49 = 21,
dsmonAggGroupIndex.2.50 = 21,
dsmonAggGroupIndex.2.51 = 21,
dsmonAggGroupIndex.2.52 = 21,
dsmonAggGroupIndex.2.53 = 21,
dsmonAggGroupIndex.2.54 = 21,
dsmonAggGroupIndex.2.55 = 21,
dsmonAggGroupIndex.2.56 = 7, -- CS7
dsmonAggGroupIndex.2.57 = 21,
dsmonAggGroupIndex.2.58 = 21,
dsmonAggGroupIndex.2.59 = 21,
dsmonAggGroupIndex.2.60 = 21,
dsmonAggGroupIndex.2.61 = 21,
dsmonAggGroupIndex.2.62 = 21,
dsmonAggGroupIndex.2.63 = 21);
Example 3: an aggregated collection of current DIFFSERV PHBs.
SET(dsmonAggGroupIndex.3.0 = 0, -- Zero CS
dsmonAggGroupIndex.3.1 = 7, -- Nonzero Default
dsmonAggGroupIndex.3.2 = 7,
dsmonAggGroupIndex.3.3 = 7,
dsmonAggGroupIndex.3.4 = 7,
Expires May 20, 2001 [Page 83]
Internet Draft DSMON MIB November 2000
dsmonAggGroupIndex.3.5 = 7,
dsmonAggGroupIndex.3.6 = 7,
dsmonAggGroupIndex.3.7 = 7,
dsmonAggGroupIndex.3.8 = 1, -- Nonzero CS
dsmonAggGroupIndex.3.9 = 7,
dsmonAggGroupIndex.3.10 = 3, -- AF1
dsmonAggGroupIndex.3.11 = 7,
dsmonAggGroupIndex.3.12 = 3,
dsmonAggGroupIndex.3.13 = 7,
dsmonAggGroupIndex.3.14 = 3,
dsmonAggGroupIndex.3.15 = 7,
dsmonAggGroupIndex.3.16 = 1,
dsmonAggGroupIndex.3.17 = 7,
dsmonAggGroupIndex.3.18 = 4, -- AF2
dsmonAggGroupIndex.3.19 = 7,
dsmonAggGroupIndex.3.20 = 4,
dsmonAggGroupIndex.3.21 = 7,
dsmonAggGroupIndex.3.22 = 4,
dsmonAggGroupIndex.3.23 = 7,
dsmonAggGroupIndex.3.24 = 1,
dsmonAggGroupIndex.3.25 = 7,
dsmonAggGroupIndex.3.26 = 5, -- AF3
dsmonAggGroupIndex.3.27 = 7,
dsmonAggGroupIndex.3.28 = 5,
dsmonAggGroupIndex.3.29 = 2, -- EF
dsmonAggGroupIndex.3.30 = 5,
dsmonAggGroupIndex.3.31 = 7,
dsmonAggGroupIndex.3.32 = 1,
dsmonAggGroupIndex.3.33 = 7,
dsmonAggGroupIndex.3.34 = 6, -- AF4
dsmonAggGroupIndex.3.35 = 7,
dsmonAggGroupIndex.3.36 = 6,
dsmonAggGroupIndex.3.37 = 7,
dsmonAggGroupIndex.3.38 = 6,
dsmonAggGroupIndex.3.39 = 7,
dsmonAggGroupIndex.3.40 = 1,
dsmonAggGroupIndex.3.41 = 7,
dsmonAggGroupIndex.3.42 = 7,
dsmonAggGroupIndex.3.43 = 7,
dsmonAggGroupIndex.3.44 = 7,
dsmonAggGroupIndex.3.45 = 7,
dsmonAggGroupIndex.3.46 = 7,
dsmonAggGroupIndex.3.47 = 7,
dsmonAggGroupIndex.3.48 = 1,
dsmonAggGroupIndex.3.49 = 7,
Expires May 20, 2001 [Page 84]
Internet Draft DSMON MIB November 2000
dsmonAggGroupIndex.3.50 = 7,
dsmonAggGroupIndex.3.51 = 7,
dsmonAggGroupIndex.3.52 = 7,
dsmonAggGroupIndex.3.53 = 7,
dsmonAggGroupIndex.3.54 = 7,
dsmonAggGroupIndex.3.55 = 7,
dsmonAggGroupIndex.3.56 = 1,
dsmonAggGroupIndex.3.57 = 7,
dsmonAggGroupIndex.3.58 = 7,
dsmonAggGroupIndex.3.59 = 7,
dsmonAggGroupIndex.3.60 = 7,
dsmonAggGroupIndex.3.61 = 7,
dsmonAggGroupIndex.3.62 = 7,
dsmonAggGroupIndex.3.63 = 7);
Example 4: initial configuration; All DSCP mappings are set to zero.
SET(dsmonAggGroupIndex.4.0 = 0, -- Initial Configuration
dsmonAggGroupIndex.4.1 = 0,
dsmonAggGroupIndex.4.2 = 0,
...
dsmonAggGroupIndex.4.63 = 0);
8.7. Step 7: Lock the Aggregation Configuration
Before any existing collections can be activated by the agent, the
aggregation configuration must be locked, by setting the
dsmonAggControlLocked scalar to 'true'.
SET(dsmonAggControlLocked.0 = true(1));
9. Intellectual Property
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to pertain
to the implementation or use of the technology described in this
document or the extent to which any license under such rights might or
might not be available; neither does it represent that it has made any
effort to identify any such rights. Information on the IETF's
procedures with respect to rights in standards-track and standards-
related documentation can be found in BCP-11. Copies of claims of
Expires May 20, 2001 [Page 85]
Internet Draft DSMON MIB November 2000
rights made available for publication and any assurances of licenses to
be made available, or the result of an attempt made to obtain a general
license or permission for the use of such proprietary rights by
implementors or users of this specification can be obtained from the
IETF Secretariat."
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary rights
which may cover technology that may be required to practice this
standard. Please address the information to the IETF Executive
Director.
10. Acknowledgements
This memo is a product of the RMONMIB WG. It is based on an Internet
Draft that was produced with a great deal of assistance from Keith
McCloghrie and Bijendra Jain.
11. References
[HCNUM]
Bierman, A., McCloghrie, K., and R. Presuhn, "Textual Conventions
for Additional High Capacity Data Types", Work in Progress,
February, 2000.
[RFC1155]
Rose, M., and K. McCloghrie, "Structure and Identification of
Management Information for TCP/IP-based Internets", RFC 1155,
Performance Systems International, Hughes LAN Systems, May 1990.
[RFC1157]
Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple Network
Management Protocol", RFC 1157, SNMP Research, Performance Systems
International, Performance Systems International, MIT Laboratory
for Computer Science, May 1990.
[RFC1212]
Rose, M., and K. McCloghrie, "Concise MIB Definitions", RFC 1212,
Performance Systems International, Hughes LAN Systems, March 1991.
[RFC1215]
M. Rose, "A Convention for Defining Traps for use with the SNMP",
RFC 1215, Performance Systems International, March 1991.
Expires May 20, 2001 [Page 86]
Internet Draft DSMON MIB November 2000
[RFC1901]
SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Introduction to Community-based SNMPv2", RFC 1901,
SNMP Research, Inc., Cisco Systems, Inc., Dover Beach Consulting,
Inc., International Network Services, January 1996.
[RFC1905]
SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Protocol Operations for Version 2 of the Simple
Network Management Protocol (SNMPv2)", RFC 1905, SNMP Research,
Inc., Cisco Systems, Inc., Dover Beach Consulting, Inc.,
International Network Services, January 1996.
[RFC1906]
SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Transport Mappings for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1906, SNMP Research, Inc., Cisco
Systems, Inc., Dover Beach Consulting, Inc., International Network
Services, January 1996.
[RFC2021]
S. Waldbusser, "Remote Network Monitoring MIB (RMON-2)", RFC 2021,
International Network Services, January 1997.
[RFC2026]
Bradner, S., "The Internet Standards Process -- Revision 3", RFC
2026, Harvard University, October, 1996.
[RFC2074]
Bierman, A., and R. Iddon, "Remote Network Monitoring MIB Protocol
Identifiers", RFC 2074, Cisco Systems, AXON Networks, Inc., January
1997.
[RFC2119]
S. Bradner, "Key words for use in RFCs to Indicate Requirement
Levels" RFC 2119, Harvard University, March 1997.
[RFC2474]
Nichols, K., Blake, S., Baker, F., and D. L. Black, "Definition of
the Differentiated Services Field (DS Field) in the IPv4 and IPv6
Headers", RFC 2474, Cisco Systems, Torrent Networking Technologies,
EMC Corporation, December, 1998.
[RFC2475]
Blake, S., Black, D., Carlson, M., Davies, E., Wang, Z., and W.
Expires May 20, 2001 [Page 87]
Internet Draft DSMON MIB November 2000
Weiss, "An Architecture for Differentiated Services", RFC 2475,
Torrent Networking Technologies, EMC Corporation, Sun Microsystems,
Nortel UK, Bell Labs Lucent Technologies, Lucent Technologies,
December, 1998.
[RFC2570]
Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction to
Version 3 of the Internet-standard Network Management Framework",
RFC 2570, SNMP Research, Inc., TIS Labs at Network Associates,
Inc., Ericsson, Cisco Systems, April 1999.
[RFC2571]
Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for
Describing SNMP Management Frameworks", RFC 2571, Cabletron
Systems, Inc., BMC Software, Inc., IBM T. J. Watson Research, April
1999.
[RFC2572]
Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message
Processing and Dispatching for the Simple Network Management
Protocol (SNMP)", RFC 2572, SNMP Research, Inc., Cabletron Systems,
Inc., BMC Software, Inc., IBM T. J. Watson Research, April 1999.
[RFC2573]
Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications", RFC
2573, SNMP Research, Inc., Secure Computing Corporation, Cisco
Systems, April 1999.
[RFC2574]
Blumenthal, U., and B. Wijnen, "User-based Security Model (USM) for
version 3 of the Simple Network Management Protocol (SNMPv3)", RFC
2574, IBM T. J. Watson Research, April 1999.
[RFC2575]
Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based Access
Control Model (VACM) for the Simple Network Management Protocol
(SNMP)", RFC 2575, IBM T. J. Watson Research, BMC Software, Inc.,
Cisco Systems, Inc., April 1999.
[RFC2578]
McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M.,
and S. Waldbusser, "Structure of Management Information Version 2
(SMIv2)", RFC 2578, STD 58, Cisco Systems, SNMPinfo, TU
Braunschweig, SNMP Research, First Virtual Holdings, International
Network Services, April 1999.
Expires May 20, 2001 [Page 88]
Internet Draft DSMON MIB November 2000
[RFC2579]
McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M.,
and S. Waldbusser, "Textual Conventions for SMIv2", RFC 2579, STD
58, Cisco Systems, SNMPinfo, TU Braunschweig, SNMP Research, First
Virtual Holdings, International Network Services, April 1999.
[RFC2580]
McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M.,
and S. Waldbusser, "Conformance Statements for SMIv2", RFC 2580,
STD 58, Cisco Systems, SNMPinfo, TU Braunschweig, SNMP Research,
First Virtual Holdings, International Network Services, April 1999.
12. Security Considerations
There are a number of management objects defined in this MIB that have a
MAX-ACCESS clause of read-write and/or read-create. Such objects may be
considered sensitive or vulnerable in some network environments. The
support for SET operations in a non-secure environment without proper
protection can have a negative effect on network operations.
There are a number of managed objects in this MIB that may contain
sensitive information. These are:
dsmonAggGroupIndex
This object may expose some basic information about the DIFFSERV
forwarding behavior for a particular segment of the network.
dsmonPdistStatsPkts
dsmonPdistStatsOctets
dsmonPdistStatsHCPkts
dsmonPdistStatsHCOctets
dsmonPdistTopNRate
dsmonPdistTopNHCRate
These objects expose some basic statistics about the DCSP distribution
for each protocol detected on a particular network interface.
dsmonHostInPkts
dsmonHostInOctets
dsmonHostInHCPkts
dsmonHostInHCOctets
Expires May 20, 2001 [Page 89]
Internet Draft DSMON MIB November 2000
dsmonHostOutPkts
dsmonHostOutOctets
dsmonHostOutHCPkts
dsmonHostOutHCOctets
dsmonHostTopNRate
dsmonHostTopNHCRate
These objects expose some basic statistics about the DCSP distribution
for each IP host detected on a particular network interface.
dsmonHostTopNAddress
This object exposes IP addresses in use on the monitored network
interfaces.
It is thus important to control even GET access to these objects and
possibly to even encrypt the values of these object when sending them
over the network via SNMP. Not all versions of SNMP provide features
for such a secure environment.
SNMPv1 by itself is not a secure environment. Even if the network
itself is secure (for example by using IPSec), even then, there is no
control as to who on the secure network is allowed to access and GET/SET
(read/change/create/delete) the objects in this MIB.
It is recommended that the implementers consider the security features
as provided by the SNMPv3 framework. Specifically, the use of the User-
based Security Model RFC 2574 [RFC2574] and the View-based Access
Control Model RFC 2575 [RFC2575] is recommended.
It is then a customer/user responsibility to ensure that the SNMP entity
giving access to an instance of this MIB, is properly configured to give
access to the objects only to those principals (users) that have
legitimate rights to indeed GET or SET (change/create/delete) them.
13. Author's Address
Andy Bierman
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA USA 95134
Phone: +1 408-527-3711
Email: abierman@cisco.com
Expires May 20, 2001 [Page 90]
Internet Draft DSMON MIB November 2000
14. Full Copyright Statement
Copyright (C) The Internet Society (2000). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it or
assist in its implementation may be prepared, copied, published and
distributed, in whole or in part, without restriction of any kind,
provided that the above copyright notice and this paragraph are included
on all such copies and derivative works. However, this document itself
may not be modified in any way, such as by removing the copyright notice
or references to the Internet Society or other Internet organizations,
except as needed for the purpose of developing Internet standards in
which case the procedures for copyrights defined in the Internet
Standards process must be followed, or as required to translate it into
languages other than English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an "AS
IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK
FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT
INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE."
Expires May 20, 2001 [Page 91]
| PAFTECH AB 2003-2026 | 2026-04-24 04:48:40 |