One document matched: draft-ietf-pppext-mschap-v2-00.txt
Network Working Group G. Zorn
Internet-Draft Microsoft Corporation
Category: Informational September 1998
<draft-ietf-pppext-mschap-v2-00.txt>
Microsoft PPP CHAP Extensions, Version 2
1. Status of this Memo
This document is an Internet-Draft. Internet-Drafts are working docu-
ments of the Internet Engineering Task Force (IETF), its areas, and its
working groups. Note that other groups may also distribute working doc-
uments as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference material
or to cite them other than as ``work in progress''.
To learn the current status of any Internet-Draft, please check the
``1id-abstracts.txt'' listing contained in the Internet-Drafts Shadow
Directories on ftp.ietf.org (US East Coast), nic.nordu.net (Europe),
ftp.isi.edu (US West Coast), or munnari.oz.au (Pacific Rim).
This memo provides information for the Internet community. This memo
does not specify an Internet standard of any kind. The distribution of
this memo is unlimited. It is filed as <draft-ietf-pppext-mschap-
v2-00.txt> and expires March 23, 1999. Please send comments to the PPP
Extensions Working Group mailing list (ietf-ppp@merit.edu) or to the
author (glennz@microsoft.com).
2. Abstract
The Point-to-Point Protocol (PPP) [1] provides a standard method for
transporting multi-protocol datagrams over point-to-point links. PPP
defines an extensible Link Control Protocol and a family of Network Con-
trol Protocols (NCPs) for establishing and configuring different net-
work-layer protocols.
This document describes version two of Microsoft's PPP CHAP dialect (MS-
CHAP-V2). MS-CHAP-V2 is similar to, but incompatible with, MS-CHAP ver-
sion one (MS-CHAP-V1, described in [9]). In particular, certain proto-
col fields have been deleted or reused but with different semantics. In
addition, MS-CHAP-V2 features mutual authentication.
The algorithms used in the generation of various MS-CHAP-V2 protocol
Zorn [Page 1]
INTERNET-DRAFT MS-CHAP-V2 July 1998
fields are described in an appendix.
3. Introduction
Where possible, MS-CHAP-V2 is consistent with both MS-CHAP-V1 and stan-
dard CHAP. Briefly, the differences between MS-CHAP-V2 and MS-CHAP-V1
are:
* MS-CHAP-V2 is enabled by negotiating CHAP Algorithm 0x81 in LCP
option 3, Authentication Protocol.
* MS-CHAP-V2 provides mutual authentication between peers by
piggybacking a peer challenge on the Response packet and an
authenticator reponse on the Success packet.
* The calculation of the "Windows NT compatible challenge
response" sub-field in the Response packet has been changed
to include the peer challenge and the user name.
* In MS-CHAP-V1, the "LAN Manager compatible challenge response"
sub-field was always sent in the Response packet. This field
has been replaced in MS-CHAP-V2 by the Peer-Challenge field.
* The format of the Message field in the Failure packet has
been changed.
* The Change Password (version 1) and Change Password (version 2)
packets are no longer supported. They have been replaced with a
single Change-Password packet.
4. Specification of Requirements
In this document, the key words "MAY", "MUST, "MUST NOT", "optional",
"recommended", "SHOULD", and "SHOULD NOT" are to be interpreted as
described in [2].
5. LCP Configuration
The LCP configuration for MS-CHAP-V2 is identical to that for standard
CHAP, except that the Algorithm field has value 0x81, rather than the
MD5 value 0x05. PPP implementations which do not support MS-CHAP-V2,
but correctly implement LCP Config-Rej, should have no problem dealing
with this non-standard option.
Zorn [Page 2]
INTERNET-DRAFT MS-CHAP-V2 July 1998
6. Challenge Packet
The MS-CHAP-V2 Challenge packet is identical in format to the standard
CHAP Challenge packet.
MS-CHAP-V2 authenticators send an 16-octet challenge Value field. Peers
need not duplicate Microsoft's algorithm for selecting the 16-octet
value, but the standard guidelines on randomness [1,2,7] SHOULD be
observed.
Microsoft authenticators do not currently provide information in the
Name field. This may change in the future.
7. Response Packet
The MS-CHAP-V2 Response packet is identical in format to the standard
CHAP Response packet. However, the Value field is sub-formatted differ-
ently as follows:
24 octets: Peer-Challenge
24 octets: NT-Response
1 octet : Flags
The Peer-Challenge field is a 16-octet random number. As the name
implies, it is generated by the peer and is used in the calculation of
the NT-Response field, below. Peers need not duplicate Microsoft's
algorithm for selecting the 16-octet value, but the standard guidelines
on randomness [1,2,7] SHOULD be observed.
The NT-Response field is an encoded function of the password, the user
name, the contents of the Peer-Challenge field and the received chal-
lenge as output by the routine GenerateNTResponse() (see section A.1,
below). The Windows NT password is a string of 0 to (theoretically) 256
case-sensitive Unicode [8] characters. Current versions of Windows NT
limit passwords to 14 characters, mainly for compatibility reasons; this
may change in the future. When computing the NT-Response field con-
tents, only the user name is used, without any associated Windows NT
domain name. This is true regardless of whether a Windows NT domain
name is present in the Name field (see below).
The Flag field is reserved for future use and MUST be zero.
The Name field is a string of 0 to (theoretically) 256 case-sensitive
ASCII characters which identifies the peer's user account name. The
Windows NT domain name may prefix the user's account name (e.g.
"BIGCO\johndoe" where "BIGCO" is a Windows NT domain containing the user
account "johndoe"). If a domain is not provided, the backslash should
Zorn [Page 3]
INTERNET-DRAFT MS-CHAP-V2 July 1998
also be omitted, (e.g. "johndoe").
8. Success Packet
The Success packet is identical in format to the standard CHAP Success
packet. However, the Message field contains a 42-octet authenticator
response string of the form
"S=<auth_string>"
where <auth_string> is a 20 octet number encoded in ASCII as 40 hexadec-
imal digits. The hexadecimal digits A-F (if present) MUST be uppercase.
This number is derived from the challenge from the Challenge packet, the
Peer-Challenge and NT-Response fields from the Response packet, and the
peer password as output by the routine GenerateAuthenticatorResponse()
(see section A.6, below). The authenticating peer MUST verify the
authenticator response when a Success packet is received. The method
for verifying the authenticator is described in section A.7, below. If
the authenticator response is either missing or incorrect, the peer MUST
end the session.
9. Failure Packet
The Failure packet is identical in format to the standard CHAP Failure
packet. There is, however, formatted text stored in the Message field
which, contrary to the standard CHAP rules, does affect the operation of
the protocol. The Message field format is:
"E=eeeeeeeeee R=r C=cccccccccccccccccccccccccccccccc V=vvvvvvvvvv"
where
The "eeeeeeeeee" is the ASCII representation of a decimal error
code (need not be 10 digits) corresponding to one of those listed
below, though implementations should deal with codes not on this
list gracefully.
646 ERROR_RESTRICTED_LOGON_HOURS
647 ERROR_ACCT_DISABLED
648 ERROR_PASSWD_EXPIRED
649 ERROR_NO_DIALIN_PERMISSION
691 ERROR_AUTHENTICATION_FAILURE
709 ERROR_CHANGING_PASSWORD
The "r" is an ASCII flag set to '1' if a retry is allowed, and '0'
if not. When the authenticator sets this flag to '1' it disables
Zorn [Page 4]
INTERNET-DRAFT MS-CHAP-V2 July 1998
short timeouts, expecting the peer to prompt the user for new cre-
dentials and resubmit the response.
The "cccccccccccccccccccccccccccccccc" is the ASCII representation
of a hexadecimal challenge value. This field MUST be exactly 32
octets long and MUST be present.
The "vvvvvvvvvv" is the ASCII representation of a decimal version
code (need not be 10 digits) indicating the password changing pro-
tocol version supported on the server. For MS-CHAP-V2, this value
SHOULD always be 3.
Implementations should accept but ignore additional text they do not
recognize.
10. Change-Password Packet
The Change-Password packet does not appear in either standard CHAP or
MS-CHAP-V1. It allows the peer to change the password on the account
specified in the preceding Response packet. The Change-Password packet
should be sent only if the authenticator reports ERROR_PASSWD_EXPIRED
(E=648) in the Message field of the Failure packet.
This packet type is supported by recent versions of Windows NT 4.0, Win-
dows 95 and Windows 98. It is not supported by Windows NT 3.5, Windows
NT 3.51, or early versions of Windows NT 4.0, Windows 95 and Windows 98.
The format of this packet is as follows:
1 octet : Code
1 octet : Identifier
2 octets : Length
516 octets : Encrypted-Password
16 octets : Encrypted-Hash
24 octets : Peer-Challenge
24 octets : NT-Response
2-octet : Flags
Code
7
Identifier
The Identifier field is one octet and aids in matching requests
and replies. The value is the Identifier of the received Failure
packet to which this packet responds plus 1.
Length
Zorn [Page 5]
INTERNET-DRAFT MS-CHAP-V2 July 1998
586
Encrypted-Password
This field contains the PWBLOCK form of the new Windows NT pass-
word encrypted with the old Windows NT password hash, as output by
the NewPasswordEncryptedWithOldNtPasswordHash() routine (see sec-
tion A.8, below).
Encrypted-Hash
This field contains the old Windows NT password hash encrypted
with the new Windows NT password hash, as output by the OldNtPass-
wordHashEncryptedWithNewNtPasswordHash() routine (see section
A.11, below).
Peer-Challenge
A 16-octet random quantity, as described in the Response packet
description.
NT-Response
The NT-Response field (as described in the Response packet
description), but calculated on the new password and the challenge
received in the Failure packet.
Flags
This field is two octets in length. It is a bit field of option
flags where 0 is the least significant bit of the 16-bit quantity.
The format of this field is illustrated in the following diagram:
1
5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Bits 0-15
Reserved, always clear (0).
11. Security Considerations
As an implementation detail, the authenticator SHOULD limit the number
of password retries allowed to make brute-force password guessing
attacks more difficult.
Zorn [Page 6]
INTERNET-DRAFT MS-CHAP-V2 July 1998
12. References
[1] Simpson, W., "The Point-to-Point Protocol (PPP)", STD 51, RFC 1661,
July 1994
[2] Simpson, W., "PPP Challenge Handshake Authentication Protocol
(CHAP)", RFC 1994, August 1996
[3] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, March 1997
[4] "Data Encryption Standard (DES)", Federal Information Processing
Standard Publication 46-2, National Institute of Standards and
Technology, December 1993
[5] Rivest, R., "MD4 Message Digest Algorithm", RFC 1320, April 1992.
[6] RC4 is a proprietary encryption algorithm available under license
from RSA Data Security Inc. For licensing information, contact:
RSA Data Security, Inc.
100 Marine Parkway
Redwood City, CA 94065-1031
[7] Eastlake, D., et. al., "Randomness Recomnendations for Security",
RFC 1750, December 1994
[8] "The Unicode Standard, Version 2.0", The Unicode Consortium, Addi-
son-Wesley, 1996. ISBN 0-201-48345-9.
[9] Zorn, G. and Cobb, S., "Microsoft PPP CHAP Extensions", draft-ietf-
pppext-mschap-00.txt (work in progress), March 1998
[10] "DES Modes of Operation", Federal Information Processing Standards
Publication 81, National Institute of Standards and Technology,
December 1980
[11] "Secure Hash Standard", Federal Information Processing Standards
Publication 180-1, National Institute of Standards and Technology,
April 1995
13. Acknowledgements
Thanks (in no particular order) to Bruce Johnson (bjohn-
son@microsoft.com), Tony Bell (tonybe@microsoft.com), Paul Leach
(paulle@microsoft.com, Terence Spies (terences@microsoft.com), Dan Simon
(dansimon@microsoft.com), Narendra Gidwani (nareng@microsoft.com), Gur-
deep Singh Pall (gurdeep@microsoft.com), Jody Terrill
Zorn [Page 7]
INTERNET-DRAFT MS-CHAP-V2 July 1998
(jodyt@extendsys.com) and Joe Davies (josephd@microsoft.com) for useful
suggestions and feedback.
14. Chair's Address
The PPP Extensions Working Group can be contacted via the current chair:
Karl Fox
Ascend Communications
3518 Riverside Drive
Suite 101
Columbus, OH 43221
Phone: +1 614 326 6841
Email: karl@ascend.com
15. Author's Address
Questions about this memo can also be directed to:
Glen Zorn
Microsoft Corporation
One Microsoft Way
Redmond, Washington 98052
Phone: +1 425 703 1559
FAX: +1 425 936 7329
EMail: glennz@microsoft.com
16. Expiration Date
This memo is filed as <draft-ietf-pppext-mschap-v2-00.txt> and expires
on March 23, 1999.
Appendix A - Pseudocode
The routines mentioned in the text are described in pseudocode below.
A.1 GenerateNTResponse()
GenerateNTResponse(
IN 16-octet AuthenticatorChallenge,
IN 16-octet PeerChallenge,
Zorn [Page 8]
INTERNET-DRAFT MS-CHAP-V2 July 1998
IN 0-to-256-char UserName,
IN 0-to-256-unicode-char Password,
OUT 24-octet Response )
{
8-octet Challenge
16-octet PasswordHash
ChallengeHash( PeerChallenge, AuthenticatorChallenge, UserName,
giving Challenge)
NtPasswordHash( Password, giving PasswordHash )
ChallengeResponse( Challenge, PasswordHash, giving Response )
}
A.2 ChallengeHash()
ChallengeHash(
IN 16-octet PeerChallenge,
IN 16-octet AuthenticatorChallenge,
IN 0-to-256-char UserName,
OUT 8-octet Challenge
{
/*
* SHAInit(), SHAUpdate() and SHAFinal() functions are an
* implementation of Secure Hash Algorithm (SHA-1) [11]. These are
* available in public domain or can be licensed from
* RSA Data Security, Inc.
*/
SHAInit(Context)
SHAUpdate(Context, PeerChallenge, 16)
SHAUpdate(Context, AuthenticatorChallenge, 16)
/*
* Only the user name (as presented by the peer and
* excluding any prepended domain name)
* is used as input to SHAUpdate().
*/
SHAUpdate(Context, UserName, strlen(Username))
SHAFinal(Context, Digest)
memcpy(Challenge, Digest, 8)
}
A.3 NtPasswordHash()
Zorn [Page 9]
INTERNET-DRAFT MS-CHAP-V2 July 1998
NtPasswordHash(
IN 0-to-256-unicode-char Password,
OUT 16-octet PasswordHash )
{
/*
* Use the MD4 algorithm [5] to irreversibly hash Password
* into PasswordHash. Only the password is hashed without
* including any terminating 0.
*/
}
A.4 ChallengeResponse()
ChallengeResponse(
IN 8-octet Challenge,
IN 16-octet PasswordHash,
OUT 24-octet Response )
{
Set ZPasswordHash to PasswordHash zero-padded to 21 octets
DesEncrypt( Challenge,
1st 7-octets of ZPasswordHash,
giving 1st 8-octets of Response )
DesEncrypt( Challenge,
2nd 7-octets of ZPasswordHash,
giving 2nd 8-octets of Response )
DesEncrypt( Challenge,
3rd 7-octets of ZPasswordHash,
giving 3rd 8-octets of Response )
}
A.5 DesEncrypt()
DesEncrypt(
IN 8-octet Clear,
IN 7-octet Key,
OUT 8-octet Cypher )
{
/*
* Use the DES encryption algorithm [4] in ECB mode [10]
* to encrypt Clear into Cypher such that Cypher can
* only be decrypted back to Clear by providing Key.
* Note that the DES algorithm takes as input a 64-bit
* stream where the 8th, 16th, 24th, etc. bits are
Zorn [Page 10]
INTERNET-DRAFT MS-CHAP-V2 July 1998
* parity bits ignored by the encrypting algorithm.
* Unless you write your own DES to accept 56-bit input
* without parity, you will need to insert the parity bits
* yourself.
*/
}
A.6 GenerateAuthenticatorResponse()
GenerateAuthenticatorResponse(
IN 0-to-256-unicode-char Password,
IN 24-octet NT-Response,
IN 16-octet PeerChallenge,
IN 16-octet AuthenticatorChallenge,
IN 0-to-256-unicode-char UserName,
OUT 42-octet AuthenticatorResponse )
{
16-octet PasswordHash
16-octet PasswordHashHash
8-octet Challenge
/*
* "Magic" constants used in response generation
*/
Magic1[39] =
{0x4D, 0x61, 0x67, 0x69, 0x63, 0x20, 0x73, 0x65, 0x72, 0x76,
0x65, 0x72, 0x20, 0x74, 0x6F, 0x20, 0x63, 0x6C, 0x69, 0x65,
0x6E, 0x74, 0x20, 0x73, 0x69, 0x67, 0x6E, 0x69, 0x6E, 0x67,
0x20, 0x63, 0x6F, 0x6E, 0x73, 0x74, 0x61, 0x6E, 0x74};
Magic2[41] =
{0x50, 0x61, 0x64, 0x20, 0x74, 0x6F, 0x20, 0x6D, 0x61, 0x6B,
0x65, 0x20, 0x69, 0x74, 0x20, 0x64, 0x6F, 0x20, 0x6D, 0x6F,
0x72, 0x65, 0x20, 0x74, 0x68, 0x61, 0x6E, 0x20, 0x6F, 0x6E,
0x65, 0x20, 0x69, 0x74, 0x65, 0x72, 0x61, 0x74, 0x69, 0x6F,
0x6E};
/*
* Hash the password with MD4
*/
NtPasswordHash( Password, giving PasswordHash )
/*
* Now hash the hash
*/
Zorn [Page 11]
INTERNET-DRAFT MS-CHAP-V2 July 1998
HashNtPasswordHash( PasswordHash, giving PasswordHashHash)
SHAInit(Context)
SHAUpdate(Context, PasswordHashHash, 16)
SHAUpdate(Context, NTResponse, 24)
SHAUpdate(Context, Magic1, 45)
SHAFinal(Context, Digest)
ChallengeHash( PeerChallenge, AuthenticatorChallenge, UserName,
giving Challenge)
SHAInit(Context)
SHAUpdate(Context, Digest, 20)
SHAUpdate(Context, Challenge, 8)
SHAUpdate(Context, Magic2, 48)
SHAFinal(Context, Digest)
/*
* Encode the value of 'Digest' as "S=" followed by
* 40 ASCII hexadecimal digits and return it in
* AuthenticatorResponse.
* For example,
* "S=0123456789ABCDEF0123456789ABCDEF01234567"
*/
}
A.7 CheckAuthenticatorResponse()
CheckAuthenticatorResponse(
IN 0-to-256-unicode-char Password,
IN 24-octet NtResponse,
IN 16-octet PeerChallenge,
IN 16-octet AuthenticatorChallenge,
IN 0-to-256-unicode-char UserName,
IN 42-octet ReceivedResponse
OUT Boolean ResponseOK )
{
20-octet MyResponse
set ResponseOK = FALSE
GenerateAuthenticatorResponse( Password, NtResponse, PeerChallenge,
AuthenticatorChallenge, UserName,
giving MyResponse)
if (MyResponse = ReceivedResponse) then set ResponseOK = TRUE
Zorn [Page 12]
INTERNET-DRAFT MS-CHAP-V2 July 1998
return ResponseOK
}
A.8 NewPasswordEncryptedWithOldNtPasswordHash()
datatype-PWBLOCK
{
256-unicode-char Password
4-octets PasswordLength
}
NewPasswordEncryptedWithOldNtPasswordHash(
IN 0-to-256-unicode-char NewPassword,
IN 0-to-256-unicode-char OldPassword,
OUT datatype-PWBLOCK EncryptedPwBlock )
{
NtPasswordHash( OldPassword, giving PasswordHash )
EncryptPwBlockWithPasswordHash( NewPassword,
PasswordHash,
giving EncryptedPwBlock )
}
A.9 EncryptPwBlockWithPasswordHash()
EncryptPwBlockWithPasswordHash(
IN 0-to-256-unicode-char Password,
IN 16-octet PasswordHash,
OUT datatype-PWBLOCK PwBlock )
{
Fill ClearPwBlock with random octet values
PwSize = lstrlenW( Password ) * sizeof( unicode-char )
PwOffset = sizeof( ClearPwBlock.Password ) - PwSize
Move PwSize octets to (ClearPwBlock.Password + PwOffset ) from Password
ClearPwBlock.PasswordLength = PwSize
Rc4Encrypt( ClearPwBlock,
sizeof( ClearPwBlock ),
PasswordHash,
sizeof( PasswordHash ),
giving PwBlock )
}
A.10 Rc4Encrypt()
Zorn [Page 13]
INTERNET-DRAFT MS-CHAP-V2 July 1998
Rc4Encrypt(
IN x-octet Clear,
IN integer ClearLength,
IN y-octet Key,
IN integer KeyLength,
OUT x-octet Cypher )
{
/*
* Use the RC4 encryption algorithm [6] to encrypt Clear of
* length ClearLength octets into a Cypher of the same length
* such that the Cypher can only be decrypted back to Clear
* by providing a Key of length KeyLength octets.
*/
}
A.11 OldNtPasswordHashEncryptedWithNewNtPasswordHash()
OldNtPasswordHashEncryptedWithNewNtPasswordHash(
IN 0-to-256-unicode-char NewPassword,
IN 0-to-256-unicode-char OldPassword,
OUT 16-octet EncryptedPasswordHash )
{
NtPasswordHash( OldPassword, giving OldPasswordHash )
NtPasswordHash( NewPassword, giving NewPasswordHash )
NtPasswordHashEncryptedWithBlock( OldPasswordHash,
NewPasswordHash,
giving EncryptedPasswordHash )
}
A.12 NtPasswordHashEncryptedWithBlock()
NtPasswordHashEncryptedWithBlock(
IN 16-octet PasswordHash,
IN 16-octet Block,
OUT 16-octet Cypher )
{
DesEncrypt( 1st 8-octets PasswordHash,
1st 7-octets Block,
giving 1st 8-octets Cypher )
DesEncrypt( 2nd 8-octets PasswordHash,
2nd 7-octets Block,
giving 2nd 8-octets Cypher )
}
Appendix B - Examples
Zorn [Page 14]
INTERNET-DRAFT MS-CHAP-V2 July 1998
B.1 Negotiation Examples
Here are some examples of typical negotiations. The peer is on the left
and the authenticator is on the right.
The packet sequence ID is incremented on each authentication retry
Response and on the change password response. All cases where the
packet sequence ID is updated are noted below.
Response retry is never allowed after Change Password. Change Password
may occur after Response retry.
B.1.1 Successful authentication
<- Challenge
Response ->
<- Success
B.1.2 Failed authentication with no retry allowed
<- Challenge
Response ->
<- Failure (E=691 R=0)
B.1.3 Successful authentication after retry
<- Challenge
Response ->
<- Failure (E=691 R=1), disable short timeout
Response (++ID) to challenge in failure message ->
<- Success
B.1.4 Failed hack attack with 3 attempts allowed
<- Challenge
Response ->
<- Failure (E=691 R=1), disable short timeout
Response (++ID) to challenge in Failure message ->
<- Failure (E=691 R=1), disable short timeout
Response (++ID) to challenge in Failure message ->
<- Failure (E=691 R=0)
B.1.5 Successful authentication with password change
Zorn [Page 15]
INTERNET-DRAFT MS-CHAP-V2 July 1998
<- Challenge
Response ->
<- Failure (E=648 R=0 V=3), disable short timeout
ChangePassword (++ID) to challenge in Failure message ->
<- Success
B.1.6 Successful authentication with retry and password change
<- Challenge
Response ->
<- Failure (E=691 R=1), disable short timeout
Response (++ID) to first challenge+23 ->
<- Failure (E=648 R=0 V=2), disable short timeout
ChangePassword (++ID) to first challenge+23 ->
<- Success
B.2 Hash Example
Intermediate values for user name "User" and password "clientPass". All
numeric values are hexadecimal.
0-to-256-char UserName:
55 73 65 72
0-to-256-unicode-char Password:
63 00 6C 00 69 00 65 00 6E 00 74 00 50 00 61 00 73 00 73 00
16-octet AuthenticatorChallenge:
5B 5D 7C 7D 7B 3F 2F 3E 3C 2C 60 21 32 26 26 28
16-octet PeerChallenge:
21 40 23 24 25 5E 26 2A 28 29 5F 2B 3A 33 7C 7E
8-octet Challenge:
D0 2E 43 86 BC E9 12 26
16-octet PasswordHash:
44 EB BA 8D 53 12 B8 D6 11 47 44 11 F5 69 89 AE
24 octet NT-Response:
82 30 9E CD 8D 70 8B 5E A0 8F AA 39 81 CD 83 54 42 33 11 4A 3D 85 D6 DF
16-octet PasswordHashHash:
41 C0 0C 58 4B D2 D9 1C 40 17 A2 A1 2F A5 9F 3F
42-octet AuthenticatorResponse:
Zorn [Page 16]
INTERNET-DRAFT MS-CHAP-V2 July 1998
"S=407A5589115FD0D6209F510FE9C04566932CDA56"
B.3 Example of DES Key Generation
DES uses 56-bit keys, expanded to 64 bits by the insertion of parity
bits. After the parity of the key has been fixed, every eighth bit is a
parity bit and the number of bits that are set (1) in each octet is odd;
i.e., odd parity. Note that many DES engines do not check parity, how-
ever, simply stripping the parity bits. The following example illus-
trates the values resulting from the use of the password "MyPw" to gen-
erate a pair of DES keys (e.g., for use in the NtPasswordHashEncrypted-
WithBlock() described in Appendix A.12).
0-to-256-unicode-char Password:
4D 79 50 77
16-octet PasswordHash:
FC 15 6A F7 ED CD 6C 0E DD E3 33 7D 42 7F 4E AC
First "raw" DES key (initial 7 octets of password hash):
FC 15 6A F7 ED CD 6C
First parity-corrected DES key (eight octets):
FD 0B 5B 5E 7F 6E 34 D9
Second "raw" DES key (second 7 octets of password hash)
0E DD E3 33 7D 42 7F
Second parity-corrected DES key (eight octets):
0E 6E 79 67 37 EA 08 FE
Zorn [Page 17]
| PAFTECH AB 2003-2026 | 2026-04-22 23:21:21 |