One document matched: draft-ietf-mpls-tp-li-lb-00.txt
Network Working Group Sami Boutros (Ed.)
Internet Draft Siva Sivabalan (Ed.)
Intended status: Standards Track Cisco Systems, Inc.
Expires: March 29, 2011
Rahul Aggarwal (Ed.)
Juniper Networks, Inc.
Martin Vigoureux (Ed.)
Alcatel-Lucent
Xuehui Dai (Ed.)
ZTE Corporation
September 29, 2010
MPLS Transport Profile Lock Instruct and Loopback Functions
draft-ietf-mpls-tp-li-lb-00.txt
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
This Internet-Draft will expire on March 29, 2007.
Abstract
Boutros Expires March 29, 2011 [Page 1]
Internet-Draft draft-ietf-mpls-tp-li-lb-00.txt September 2010
This document specifies an extension to MPLS Operation,
administration, and Maintenance (OAM) to operate an MPLS Transport
Profile (MPLS-TP) Label Switched Path (LSP), bi-directional RSVP-TE
tunnels, pseudowires (PW), or Multi-segment PWs in loopback mode for
management purpose. This extension includes mechanism to lock and
unlock MPLS-TP Tunnels (i.e. data and control traffic) and can be
used to loop all traffic (i.e, data and control traffic) at a
specified LSR on the path of the MPLS-TP LSP back to the source.
Table of Contents
1. Introduction...................................................3
2. Terminology....................................................4
3. MPLS-TP Loopback/Lock Mechanism................................5
3.1. In-band Message Identification............................5
3.2. MPLS LI-LB Message Format.................................5
3.3. LSP Ping Extensions.......................................8
3.3.1. Lock Request TLV.....................................8
3.3.2. Unlock Request TLV...................................8
3.3.3. Loopback Request TLV.................................8
3.3.4. Loopback Removal TLV.................................9
3.3.5. Response TLV.........................................9
3.3.6. Authentication TLV..................................10
4. Loopback/Lock Operations......................................10
4.1. Lock Request.............................................10
4.2. Unlock Request...........................................10
4.3. Loopback Request.........................................11
4.4. Loopback Removal.........................................11
5. Data packets..................................................11
6. Operation.....................................................12
6.1. General Procedures.......................................12
6.2. Example Topology.........................................12
6.3. Locking an LSP...........................................13
6.4. Unlocking an LSP.........................................13
6.5. Setting an LSP into Loopback mode........................14
6.6. Removing an LSP from Loopback mode.......................15
7. Security Considerations.......................................16
8. IANA Considerations...........................................16
TBD..............................................................16
9. References....................................................16
9.1. Normative References.....................................16
9.2. Informative References...................................17
Author's Addresses...............................................17
Full Copyright Statement.........................................19
Intellectual Property Statement..................................19
Boutros Expires March 29, 2011 [Page 2]
Internet-Draft draft-ietf-mpls-tp-li-lb-00.txt September 2010
1. Introduction
In traditional transport networks, circuits are provisioned across
multiple nodes and service providers have the ability to operate the
transport circuit such as T1 line in loopback mode for management
purposes, e.g., to test or verify connectivity of the circuit up to a
specific node on the path of the circuit, to test the circuit
performance with respect to delay/jitter, etc. MPLS-TP bidirectional
LSP emulating traditional transport circuits need to provide the same
loopback capability. The mechanisms in this document apply to
associated bidirectional paths as defined in [7], which include MPLS-
TP LSPs, bi-directional RSVP-TE tunnels, pseudowires (PW), and Multi-
segment PWs.
To describe the loopback functionality, let us assume a bi-
directional MPLS-TP LSP A <---> B <---> C <---> D where A, B, C, and
D are MPLS capable nodes. Also, let us assume that the network
operator requires C to loop, back to A, the packets sent from A. In
this example, A and D acts as Maintenance End Points (MEPs) and C
acts as a Maintenance Intermediate Point (MIP). The operator can
setup the MPLS-TP LSP into loopback mode such that C loops all the
packets (regardless of whether they are data or control packets)
generated by node A back to A. The packets are not also forwarded
towards D. Similarly, any traffic received by C from the reverse
direction will be dropped.
The operator must take the MPLS-TP LSP out of service before setting
up the MPLS-TP LSP in loopback mode. This is accomplished by the MEP
establishing the loopback first sending a Lock command to the remote
MEP(s). In the case above, A sends a Lock request message along the
MPLS-TP LSP and destined to D to lock the MPLS-TP LSP. The message
will be intercepted by D since it is at the end of the LSP. D
responds to the lock request with a reply message specifying whether
it can take the LSP out of service or not.
In order to set the MPLS-TP LSP in loopback mode, A sends a Loopback
request message to the MIP or MEP where the loopback is to be
enabled. In the above example, the MPLS TTL value is set so that the
message will be intercepted by C.
This message contains a request to instruct C to operate the
corresponding MPLS-TP LSP in Loopback mode. C responds to the
Loopback request with a reply message back to A to indicate whether
or not it has successfully set the MPLS-TP LSP into the loopback
mode. If the loopback cannot be set, the reply message would contain
an error code. Upon receiving such a reply to the loopback request, A
logs the event and takes further reporting actions as necessary. If
the MPLS-TP LSP was previously locked, A sends another request
message to D to unlock it.
Boutros Expires March 29, 2011 [Page 3]
Internet-Draft draft-ietf-mpls-tp-li-lb-00.txt September 2010
If the loopback request can be performed, the input LSP from the
direction of A is directly cross-connected to the output LSP towards
A. All the packets generated by node A (data and control) are looped
back at C, excepting the case of TTL expiration.
When the loopback operation is no longer required, A sends a request
message to remove the loopback and thus restore the LSP to its
original forwarding state. In this example the MPLS TTL is set such
that this message is intercepted by C. It is expected that C sends a
reply back to A to with a return code either ACKing or NAK the
loopback removal request. Upon getting an ACK response to loopback
mode removal request, A sends another request message to unlock the
MPLS-TP LSP. The packet is intercepted by D as it is at the end of
the MPLS-TP LSP.
The proposed mechanism is based on a new set of messages and TLVs
which can be transported using one of the following methods:
(1) An in-band MPLS message transported using a new ACH code point,
the message will have different types to perform the loopback
request/remove and Lock/unlock functions, and may carry new set of
TLVs.
(2) A new set of TLVs which can be transported using LSP-Ping
extensions defined in [4], and in compliance to specifications [5].
Method (1) and (2) are referred to as "in-band option" and "LSP-Ping
option" respectively in the rest of the document.
Conventions used in this document
In examples, "C:" and "S:" indicate lines sent by the client and
server respectively.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC-2119 [3].
2. Terminology
ACH: Associated Channel Header
LSR: Label Switching Router
MEP: Maintenance Entity Group End Point
MIP: Maintenance Entity Group Intermediate Point.
MPLS-TP: MPLS Transport Profile
Boutros Expires March 29, 2011 [Page 4]
Internet-Draft draft-ietf-mpls-tp-li-lb-00.txt September 2010
MPLS-OAM: MPLS Operations, Administration and Maintenance
MPLS-TP LSP: Bidirectional Label Switch Path representing a circuit
NMS: Network Management System
TLV: Type Length Value
TTL: Time To Live
LI-LB: Lock instruct-Loopback
3. MPLS-TP Loopback/Lock Mechanism
For the in-band option, the proposed mechanism uses a new code point
in the Associated Channel Header (ACH) described in [6].
3.1. In-band Message Identification
In the in-band option, the MPLS-TP LI-LB channel is identified by the
ACH as defined in RFC 5586 [6] with the Channel Type set to the MPLS-
TP LI-LB code point = 0xHH. [HH to be assigned by IANA from the PW
Associated Channel Type registry] The LI-LB Channel does not use ACH
TLVs and MUST not include the ACH TLV header. The LI-LB ACH
Channel is shown below.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0 0 0 1|Version|Reserved | 0xHH (MPLS-TP LI-LB) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 1: ACH Indication of MPLS-TP LI-LB
The LI-LB Channel is 0xHH (to be assigned by IANA)
3.2. MPLS LI-LB Message Format
The format of an MPLS-TP LI-LB Message is shown below.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Version | Message Type | Operation | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Return Code | Cause Code | Message Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Sender's Handle |
Boutros Expires March 29, 2011 [Page 5]
Internet-Draft draft-ietf-mpls-tp-li-lb-00.txt September 2010
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Message ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TLV's |
~ ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2: MPLS LI-LB Message Format
Version: The Version Number is currently 1. (Note: the version
number is to be incremented whenever a change is made that affects
the ability of an implementation to correctly parse or process the
request/response message. These changes include any syntactic or
semantic changes made to any of the fixed fields, or to any Type-
Length-Value (TLV) or sub-TLV assignment or format that is defined at
a certain version number. The version number may not need to be
changed if an optional TLV or sub-TLV is added.)
Message Type
Two message types are defined as shown below.
Message Type Description
------------ -------------
0x0 LI-LB request
0x1 LI-LB response
Operation
Four operations are defined as shown below. The operations can appear
in a Request or Response message.
Operation Description
--------- -------------
0x1 Lock
0x2 Unlock
0x3 Set_Loopback
0x4 Unset_Loopback
Message Length
The total length of any included TLVs.
Sender's Handle
The Sender's Handle is filled in by the sender, and returned
unchanged by the receiver in the MPLS response message (if any).
Boutros Expires March 29, 2011 [Page 6]
Internet-Draft draft-ietf-mpls-tp-li-lb-00.txt September 2010
There are no semantics associated with this handle, although a sender
may find this useful for matching up requests with replies.
Message ID
The Message ID is set by the sender of an MPLS request message. It
MUST be copied unchanged by the receiver in the MPLS response message
(if any). A sender SHOULD increment this value on each new message.
A retransmitted message SHOULD leave the value unchanged.
Return code
Value Meaning
----- -------
0 Informational
1 Success
2 Failure
Cause code
Value Meaning
----- -------
0 No cause code
1 Fail to match target MIP/MEP ID
2 Malformed request received
3 One or more of the TLVs is/are unknown
4 Authentication failed
5 MPLS-TP LSP/PW already locked
6 MPLS-TP LSP/PW already unlocked
7 Fail to lock MPLS-TP LSP/PW
8 Fail to unlock MPLS-TP LSP/PW
9 MPLS-TP LSP/PW already in loopback mode
10 MPLS-TP LSP/PW is not in loopback mode
11 Fail to set MPLS-TP LSP/PW in loopback mode
12 Fail to remove MPLS-TP/PW from loopback mode
13 No label binding for received message
The Return code and Cause code only have meaning in a Response
message. In a request message the Return code and Cause code must be
set to zero and ignored on receipt.
Boutros Expires March 29, 2011 [Page 7]
Internet-Draft draft-ietf-mpls-tp-li-lb-00.txt September 2010
3.3. LSP Ping Extensions
3.3.1. Lock Request TLV
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| type = TBD | length = 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
A MEP includes a Lock Request TLV in the MPLS LSP Ping echo request
message to request the MEP on the other side of the MPLS-TP LSP to
take the LSP out of service.
3.3.2. Unlock Request TLV
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| type = TBD | length = 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The Unlock Request TLV is sent from the MEP which has previously sent
lock request. Upon receiving the LSP Ping Echo request message with
the unlock request TLV, the receiver MEP brings the MPLS-TP LSP back
in service.
3.3.3. Loopback Request TLV
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| type = TBD | length = 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
When a MEP wants to put an MPLS-TP LSP in loopback mode, it sends a
MPLS LSP Ping echo request message with Loopback Request TLV. The
message can be intercepted by either a MIP or a MEP depending on the
MPLS TTL value. The receiver puts in corresponding MPLS-TP LSP in
loopback mode.
Boutros Expires March 29, 2011 [Page 8]
Internet-Draft draft-ietf-mpls-tp-li-lb-00.txt September 2010
3.3.4. Loopback Removal TLV
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| type = TBD | length = 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
When loopback mode operation of an MPLS-TP LSP is no longer required,
the MEP that previously sent the MPLS LSP Ping echo request message
with a loopback TLV, sends another MPLS LSP Ping echo request message
with a Loopback Removal TLV. The receiver MEP changes the MPLS-TP LSP
from loopback mode to normal mode of operation.
3.3.5. Response TLV
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| type = TBD | Length = 0x1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|ReturnCode |
+-+-+-+-+-+-+-+
Return code
Value Meaning
----- -------
0 Success
1 Fail to match target MIP/MEP ID
2 Malformed loopback request received
3 One or more of the TLVs is/are unknown
4 Authentication failed
5 MPLS-TP LSP/PW already locked
6 MPLS-TP LSP/PW already unlocked
7 Fail to lock MPLS-TP LSP/PW
8 Fail to unlock MPLS-TP LSP/PW
9 MPLS-TP LSP/PW already in loopback mode
10 MPLS-TP LSP/PW is not in loopback mode
11 Fail to set MPLS-TP LSP/PW in loopback mode
12 Fail to remove MPLS-TP LSP/PW from loopback mode
13 No label binding for received message
Note that in the case of error code 3, the unknown TLV can also be
optionally included in the response TLV.
Boutros Expires March 29, 2011 [Page 9]
Internet-Draft draft-ietf-mpls-tp-li-lb-00.txt September 2010
3.3.6. Authentication TLV
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| type = TBD | Length = 0xx |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Variable Length Value |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Mechanisms similar to PPP Chap can be used to authenticate the
Loopback request. A variable length key can be carried in an optional
authentication TLV which can be included in the MPLS OAM LSP Ping
echo request message containing a loopback request TLV or the LI-LB
Message. The use of authentication key is outside the scope of the
document.
4. Loopback/Lock Operations
4.1. Lock Request
Lock Request is used to request a MEP to take an MPLS-TP LSP out of
service so that some form of maintenance can be done.
The receiver MEP MUST send either an ACK or a NAK response to the
sender MEP. Until the sender MEP receives an ACK, it MUST NOT assume
that the receiver MEP has taken the MPLS-TP LSP out of service. A
receiver MEP sends an ACK only if it can successfully lock the MPLS-
TP LSP. Otherwise, it sends a NAK.
4.2. Unlock Request
The Unlock Request is sent from the MEP which has previously sent
lock request. Upon receiving the unlock request message, the receiver
MEP brings the MPLS-TP LSP back in service.
The receiver MEP MUST send either an ACK or a NAK response to the
sender MEP. Until the sender MEP receives an ACK, it MUST NOT assume
that the MPLS-TP LSP has been put back in service. A receiver MEP
sends an ACK only if the MPLS-TP LSP has been unlocked, and unlock
operation is successful. Otherwise, it sends a NAK.
Boutros Expires March 29, 2011 [Page 10]
Internet-Draft draft-ietf-mpls-tp-li-lb-00.txt September 2010
4.3. Loopback Request
When a MEP wants to put an MPLS-TP LSP in loopback mode, it sends a
Loopback request message. The message can be intercepted by either a
MIP or a MEP depending on the MPLS TTL value. The receiver puts in
corresponding MPLS-TP LSP in loopback mode.
The receiver MEP or MIP MUST send either an ACK or NAK response to
the sender MEP. An ACK response is sent if the MPLS-TP LSP is
successfully put in loopback mode. Otherwise, a NAK response is sent.
Until an ACK response is received, the sender MEP MUST NOT assume
that the MPLS-TP LSP can operate in loopback mode.
4.4. Loopback Removal
When loopback mode operation of an MPLS-TP LSP is no longer required,
the MEP that previously sent the Loopback request message sends
another Loopback Removal message. The receiver MEP changes the MPLS-
TP LSP from loopback mode to normal mode of operation.
The receiver MEP or MIP MUST send either an ACK or NAK response to
the sender MEP. An ACK response is sent if the MPLS-TP LSP is already
in loopback mode, and if the MPLS-TP LSP is successfully put back in
normal operation mode. Otherwise, a NAK response is sent. Until an
ACK response is received, the sender MEP MUST NOT assume that the
MPLS-TP LSP is put back in normal operation mode.
5. Data packets
Data packets sent from the sender MEP will be looped back to that
sender MEP. In order for the sender MEP node to make sure that no
data packets are dropped, each data MPLS packets may contain a
sequence-id right after the label stack. A time-stamp fields in the
data packets can help calculate the Round trip delay of datapackets.
The Local Time-Stamp is set by the sender, and can be used to
calculate the round trip delay after the message is looped back.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Label with EOS bit set |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Length | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Sequence-Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Time-Stamp |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Boutros Expires March 29, 2011 [Page 11]
Internet-Draft draft-ietf-mpls-tp-li-lb-00.txt September 2010
| Time-Stamp |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Arbitrary Padding |
: :
| Arbitrary Padding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
6. Operation
6.1. General Procedures
When placing an LSP into Loopback mode, the operation MUST first be
preceded by a Lock operation.
Sending LSP Ping Echo Request message with Loopback Request/Removal
or in-Band Loopback Request/Removal Message
The TTL of the topmost label is set as follows:-
If the target node is a MIP, the TTL MUST be set to the exact number
of hops required to reach that MIP.
If the target node is a MEP, the value MUST be set to at least the
number of hops required to reach that MEP. For most operations where
the target is a MEP, the TTL MAY be set to 255.
However, to remove a MEP from Loopback mode, the sending MEP MUST set
the TTL to the exact number of hops required to reach the MEP (if the
TTL were set higher, the Loopback removal message would be looped
back toward the sender). It is RECOMMENDED that the TTL be set to the
exact number of hops required to reach the MEP.
6.2. Example Topology
The next four sections discuss the procedures for Locking, Unlocking,
setting an LSP into loopback, and removing the loopback. The
description is worded using an example. Assume an MPLS-TP LSP
traverses nodes A <--> B <--> C <--> D. We will refer to the
Maintenance Entities involved as MEP-A, MIP-B, MIP-C, and MEP-D
respectively. Suppose a maintenance operation invoked at node A
requires a loopback be set at node C. To invoke Loopack mode at node
C, A would first need to lock the LSP. Then it may proceed to set the
loopback at C. Following the loopback operation, A would need to
remove the loopback at C and finally unlock the LSP.
The following sections describe MEP-A setting and unsetting a lock at
MEP-D and then setting and removing a loopback at MIP-C.
Boutros Expires March 29, 2011 [Page 12]
Internet-Draft draft-ietf-mpls-tp-li-lb-00.txt September 2010
6.3. Locking an LSP
1. MEP-A sends an MPLS LSP Ping Echo request message with the Lock
TLV or an in-Band Lock request Message. Optionally, an authentication
TLV MAY be included.
2. Upon receiving the request message, D uses the received label
stack and the Target FEC/source MEP-ID to identify the LSP. If no
label binding exists or there is no associated LSP back to the
originator, the event is logged. Processing ceases. Otherwise the
message is delivered to the target MEP.
a. if the source MEP-ID does not match, the event is logged and
processing ceases.
b. if the target MEP-ID does not match, MEP-D sends a response with
error code 1.
MEP-D then examines the message, and:
c. if the message is malformed, it sends a response with error code 2
back to MEP-A.
d. if message authentication fails, it MAY send a response with error
code 4 back to MEP-A.
e. if any of the TLVs is not known, it sends a response with error
code 3 back to MEP-A. It may also include the unknown TLVs.
f. if the MPLS-TP LSP is already locked, it sends a response with
error code 5 back to MEP-A.
g. if the MPLS-TP LSP is not already locked and cannot be locked, it
sends a response with error code 7 back to A.
h. if the MPLS-TP LSP is successfully locked, it sends a response
with error code 0 (Success) back to MEP-A.
The response is sent using an MPLS LSP Ping echo reply with a
response TLV or an in-Band Lock response message. An authentication
TLV MAY be included.
6.4. Unlocking an LSP
1. MEP-A sends an MPLS Echo request message with the unLock TLV or an
in-Band unLock request Message. Optionally, an authentication TLV MAY
be included.
2. Upon receiving the unLock request message, D uses the received
label stack and target FEC/source MEP-ID to identify the LSP. If no
Boutros Expires March 29, 2011 [Page 13]
Internet-Draft draft-ietf-mpls-tp-li-lb-00.txt September 2010
label binding exists or there is no associated LSP back to the
originator, the event is logged. Processing ceases. Otherwise the
message is delivered to the target MEP.
a. if the source MEP-ID does not match, the event is logged and
processing ceases.
b. if the target MEP-ID does not match, MEP-D sends a response with
error code 1.
MEP-D then examines the message, and:
c. if the message is malformed, it sends a response with error code 2
back to MEP-A.
d. if message authentication fails, it MAY send a response with error
code 4 back to MEP-A.
e. if any of the TLVs is not known, it sends a response with error
code 3 back to MEP-A. It may also include the unknown TLVs.
f. if the MPLS-TP LSP is already unlocked, it sends a response with
error code 6 back to MEP-A.
g. if the LSP is locked and cannot be unlocked, it sends a response
with error code 8 back to MEP-A.
h. if the LSP is successfully unlocked, it sends a response with
error code 0 (Success) back to MEP-A.
The response is sent using an MPLS LSP Ping echo reply with a
response TLV or an in-Band unlock response message. An authentication
TLV MAY be included.
6.5. Setting an LSP into Loopback mode
1. MEP-A sends an MPLS LSP Ping Echo request message with the
loopback TLV or an in-Band Loopback request message. Optionally, an
authentication TLV MAY be included.
2. Upon intercepting the MPLS Loopback message via TTL expiration, C
uses the received label stack and target FEC/source MEP-ID to
identify the LSP.
If no label binding exists or there is no associated LSP back to the
originator, the event is logged. Processing ceases.
Otherwise the message is delivered to the target MIP/MEP - in this
case MIP-C.
Boutros Expires March 29, 2011 [Page 14]
Internet-Draft draft-ietf-mpls-tp-li-lb-00.txt September 2010
a. if the source MEP-ID does not match, the event is logged and
processing ceases.
b. if the target MIP-ID does not match, MIP-C sends a response with
error code 1.
MIP-C then examines the message, and:
c. if the message is malformed, it sends a response with error code 2
back to MEP-A.
d. if the message authentication fails, it sends a response with
error code 4 back to MEP-A.
e. if any of the TLV is not known, C sends a response with error code
3 back to MEP-A. It may also include the unknown TLVs.
f. if the MPLS-TP LSP is already in the requested loopback mode, it
sends a response with error code 9 back to MEP-A.
g. if the MPLS-TP LSP is not already in the requested loopback mode
and that loopback mode cannot be set, it sends a response with error
code 11 back to MEP-A.
h. if the MPLS-TP LSP is successfully programmed into the requested
loopback mode, it sends a response with error code 0 (Success) back
to MEP-A.
The response is sent using an MPLS LSP Ping echo reply with a
response TLV or an in-Band Loopback response message. An
authentication TLV MAY be included.
6.6. Removing an LSP from Loopback mode
1. MEP-A sends a MPLS LSP Ping Echo request message with the Loopback
removal TLV or an in-Band Loopback removal request message.
Optionally, an authentication TLV MAY be included.
2. Upon intercepting the MPLS Loopback removal message via TTL
expiration, C uses the received label stack and the target FEC/source
MEP-ID to identify the LSP.
If no label binding exists or there is no associated LSP back to
the originator, the event is logged. Processing ceases.
Otherwise the message is delivered to the target MIP/MEP - in this
case MIP-C.
a. if the source MEP-ID does not match, the event is logged and
processing ceases.
Boutros Expires March 29, 2011 [Page 15]
Internet-Draft draft-ietf-mpls-tp-li-lb-00.txt September 2010
b. if the target MIP-ID does not match, MIP-C sends a response with
error code 1 back to MEP-A.
MIP-C then examines the message, and:
c. if the message is malformed, it sends a response with error code 2
back to MEP-A.
d. if the message authentication fails, it sends a response with
error code 4 back to MEP-A.
e. if any of the TLV is not known, C sends a response with error code
3 back to MEP-A. It may also include the unknown TLVs.
f. if the MPLS-TP is not in loopback mode, it sends a response with
error code 10 back to MEP-A.
g. if the MPLS-TP LSP loopback cannot be removed, it sends a response
with error code 12 back to MEP-A.
h. if the MPLS-TP is successfully changed from loopback mode to
normal mode of operation, it sends a reply with error code 0 (Success
) back to MEP-A.
The response is sent using an MPLS LSP Ping echo reply with a
response TLV or an in-Band Loopback removal response message. An
authentication TLV MAY be included.
7. Security Considerations
The security considerations for the authentication TLV need further
study.
8. IANA Considerations
TBD
9. References
9.1. Normative References
[1] Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and
S. Ueno, "Requirements of an MPLS Transport Profile", RFC 5654,
September 2009.
[2] Vigoureux, M., Ward, D., and M. Betts, "Requirements for
Operations, Administration, and Maintenance (OAM) in MPLS
Transport Networks", RFC 5860, May 2010.
Boutros Expires March 29, 2011 [Page 16]
Internet-Draft draft-ietf-mpls-tp-li-lb-00.txt September 2010
[3] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, March 1997.
[4] K. Kompella, G. Swallow, "Detecting Multi-Protocol Label
Switched (MPLS) Data Plane Failures", RFC 4379, February 2006.
[5] N. Bahadur, et. al., "MPLS on-demand Connectivity Verification,
Route Tracing and Adjacency Verification", draft-nitinb-mpls-
tp-on-demand-cv-00, work in progress, June 2010
[6] Bocci, M., Vigoureux, M., and S. Bryant, "MPLS Generic
Associated Channel", RFC 5586, June 2009.
[7] Bocci, M. and G. Swallow, "MPLS-TP Identifiers", draft-ietf-
mpls-tp-identifiers-01 (work in progress), June 2010.
[8] Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and
S.Ueno, "Requirements of an MPLS Transport Profile", RFC 5654,
September 2009.
9.2. Informative References
[9] Nabil Bitar, et. al, "Requirements for Multi-Segment Pseudowire
Emulation Edge-to-Edge (PWE3) ", RFC5254, October 2008.
Author's Addresses
Sami Boutros
Cisco Systems, Inc.
Email: sboutros@cisco.com
Siva Sivabalan
Cisco Systems, Inc.
Email: msiva@cisco.com
Rahul Aggarwal
Juniper Networks.
EMail: rahul@juniper.net
Martin Vigoureux
Alcatel-Lucent.
Email: martin.vigoureux@alcatel-lucent.com
Xuehui Dai
ZTE Corporation.
Email: dai.xuehui@zte.com.cn
Boutros Expires March 29, 2011 [Page 17]
Internet-Draft draft-ietf-mpls-tp-li-lb-00.txt September 2010
George Swallow
Cisco Systems, Inc.
Email: swallow@cisco.com
David Ward
Juniper Networks.
Email: dward@juniper.net
Stewart Bryant
Cisco Systems, Inc.
Email: stbryant@cisco.com
Carlos Pignataro
Cisco Systems, Inc.
Email: cpignata@cisco.com
Nabil Bitar
Verizon.
Email: nabil.bitar@verizon.com
Italo Busi
Alcatel-Lucent.
Email: italo.busi@alcatel-lucent.it
Lieven Levrau
Alcatel-Lucent.
Email: llevrau@alcatel-lucent.com
Laurent Ciavaglia
Alcatel-Lucent.
Email: laurent.ciavaglia@alcatel-lucent.com
Bo Wu
ZTE Corporation.
Email: wu.bo@zte.com.cn
Jian Yang
ZTE Corporation.
Email: yang_jian@zte.com.cn
Boutros Expires March 29, 2011 [Page 18]
Internet-Draft draft-ietf-mpls-tp-li-lb-00.txt September 2010
Full Copyright Statement
Copyright (c) 2008 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
All IETF Documents and the information contained therein are provided
on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE
REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE
IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY
WARRANTY THAT THE USE OF THE INFORMATION THEREIN WILL NOT INFRINGE
ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE.
Intellectual Property Statement
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights.
Copies of Intellectual Property disclosures made to the IETF
Secretariat and any assurances of licenses to be made available, or
the result of an attempt made to obtain a general license or
permission for the use of such proprietary rights by implementers or
users of this specification can be obtained from the IETF on-line IPR
repository at http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
any standard or specification contained in an IETF Document. Please
address the information to the IETF at ietf-ipr@ietf.org.
The definitive version of an IETF Document is that published by, or
under the auspices of, the IETF. Versions of IETF Documents that are
published by third parties, including those that are translated into
other languages, should not be considered to be definitive versions
Boutros Expires March 29, 2011 [Page 19]
Internet-Draft draft-ietf-mpls-tp-li-lb-00.txt September 2010
of IETF Documents. The definitive version of these Legal Provisions
is that published by, or under the auspices of, the IETF. Versions of
these Legal Provisions that are published by third parties, including
those that are translated into other languages, should not be
considered to be definitive versions of these Legal Provions.
For the avoindance od doubt, each Contributor to the UETF Standards
Process licenses each Contribution that he or she makes as part of
the IETF Standards Process to the IETF Trust pursuant to the
provisions of RFC 5378. No language to the contrary, or terms,
conditions or rights that differ from or are inconsistent with the
rights and licenses granted under RFC 5378, shall have any effect and
shall be null and void, whether published or posted by such
Contributor, or included with or in such Contribution.
Acknowledgment
Funding for the RFC Editor function is currently provided by the
Internet Society.
Boutros Expires March 29, 2011 [Page 20]
| PAFTECH AB 2003-2026 | 2026-04-23 06:56:03 |