One document matched: draft-ietf-mip6-bootstrapping-split-00.txt
MIP6 WG G. Giaretta, Editor
Internet Draft Tilab
Expires: December 22, 2005 J. Kempf
DoCoMo Labs USA
V. Devarapalli
Nokia
June 22, 2005
Mobile IPv6 bootstrapping in split scenario
draft-ietf-mip6-bootstrapping-split-00.txt
Status of this Memo
By submitting this Internet-Draft, each author represents that
any applicable patent or other IPR claims of which he or she is
aware have been or will be disclosed, and any of which he or she
becomes aware will be disclosed, in accordance with Section 6 of
BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
This Internet-Draft will expire on December 22, 2005.
Copyright Notice
Copyright (C) The Internet Society (2005). All Rights Reserved.
Abstract
A Mobile IPv6 node requires a Home Agent address, a home address, and
IPsec security associations with its Home Agent before it can start
G. Giaretta, Ed. Expires December 22, 2005 [Page 1]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
utilizing Mobile IPv6 service. RFC 3775 requires that some or all of
these are statically configured. This document defines how a Mobile
IPv6 node can bootstrap this information from non-topological
information and security credentials preconfigured on the Mobile
Node. The solution defined in this document solves the boostrapping
problem from draft-ietf-mip6-bootstrapping-ps-02 when the Mobile
Node's mobility service is authorized by a different service provider
than basic network access, and is therefore generically applicable to
any bootstrapping case.
Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC-2119 [1].
G. Giaretta, Ed. Expires December 22, 2005 [Page 2]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
Table of Contents
1. Introduction...................................................4
2. Terminology....................................................5
3. Split scenario.................................................6
4. Components of the solution.....................................8
5. Protocol Operations...........................................10
5.1. Home Agent Address Discovery.............................10
5.1.1. DNS lookup by Home Agent Name.......................10
5.1.2. DNS lookup by service name..........................11
5.2. IPsec Security Associations setup........................12
5.3. Home Address assignment..................................12
5.3.1. Home Address assignment by the Home Agent...........12
5.3.2. Home Address auto-configuration by the Mobile Node..12
5.4. Authorization and Authentication with MSA................14
6. Home Address registration in the DNS..........................16
7. Summary of Bootstrapping Protocol Flow........................18
8. Option and Attribute Format...................................20
8.1. DNS Update mobility option...............................20
8.2. MIP6_HOME_PREFIX attribute...............................21
9. Security Considerations.......................................23
9.1. HA Address Discovery.....................................23
9.2. Home Address Assignment through IKEv2....................24
9.3. SA Establishment Using EAP Through IKEv2.................25
9.4. Back End Security Between the HA and AAA Server..........25
9.5. Dynamic DNS Update.......................................25
10. IANA Considerations..........................................27
11. Contributors.................................................28
12. References...................................................29
12.1. Normative References....................................29
12.2. Informative References..................................29
Authors' Addresses...............................................31
Intellectual Property Statement..................................32
Disclaimer of Validity...........................................32
Copyright Statement..............................................32
Acknowledgment...................................................32
G. Giaretta, Ed. Expires December 22, 2005 [Page 3]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
1. Introduction
Mobile IPv6 [2] requires the Mobile Node to know its Home Agent
Address, its own Home Address and the cryptographic materials (e.g.
shared keys or certificates) needed to set-up IPsec security
associations with the Home Agent in order to protect MIPv6 signaling.
This is generally referred to as the Mobile IPv6 bootstrapping
problem [4].
Mobile IPv6 base protocol does not specify any method to
automatically acquire this information, which means that network
administrators are normally required to manually set configuration
data on MNs and HAs. However, in real deployments, manual
configuration does not scale as the Mobile Nodes increase in number.
As discussed in [4], several bootstrapping scenarios can be
identified depending on the relationship between the network operator
that authenticates a mobile host for granting network access service
(Access Service Authorizer, ASA) and the service provider that
authorizes Mobile IPv6 service (Mobility Service Authorizer, MSA).
This document describes a solution to the bootstrapping problem that
is applicable in a scenario where the MSA and the ASA are different
entities (i.e. split scenario).
G. Giaretta, Ed. Expires December 22, 2005 [Page 4]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
2. Terminology
General mobility terminology can be found in [8]. The following
additional terms are used here:
ASA
Access Service Authorizer. A network operator that authenticates
a mobile host and establishes the mobile host's authorization to
receive Internet service.
ASP
Access Service Provider. A network operator that provides direct
IP packet forwarding to and from the end host.
MSA
Mobility Service Authorizer. A service provider that authorizes
Mobile IPv6 service.
MSP
Mobility Service Provider. A service provider that provides
Mobile IPv6 service. In order to obtain such service, the mobile
host must be authenticated and prove authorization to obtain the
service.
Split scenario
A scenario where mobility service and network access service are
authorized by different entities. This implies that MSA is
different from ASA.
G. Giaretta, Ed. Expires December 22, 2005 [Page 5]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
3. Split scenario
In the problem statement draft [4] there is a clear assumption that
mobility service and network access service can be separate. This
assumption implies that mobility service and network access service
may be authorized by different entities. As an example, the service
model defined in [4] allows an enterprise network to deploy a Home
Agent and offer Mobile IPv6 service to a user, even if the user is
accessing the Internet independent of its enterprise account (e.g.,
by using his personal WiFi hotspot account at a coffee shop).
Therefore, in this document it is assumed that network access and
mobility service are authorized by different entities, which means
that authentication and authorization for mobility service and
network access will be considered separately. This scenario is called
split scenario.
Moreover, the model defined in [4] separates the entity providing the
service from the entity that authenticates and authorizes the user.
This is similar to the roaming model for network access. Therefore,
in the split scenario, two different cases can be identified
depending on the relationship between the entity that provides the
mobility service (i.e. Mobility Service Provider, MSP) and the entity
that authenticates and authorizes the user (i.e. Mobility Service
Authorizer, MSA).
Figure 1 depicts the split scenario when the MSP and the MSA are the
same entity. This means that the network operator that provides the
Home Agent authenticates and authorizes the user for mobility
service.
Mobility Service
Provider and Authorizer
+-------------------------------------------+
| |
| +-------------+ +--+ |
| | MSA/MSP AAA | <-------------> |HA| |
| | server | AAA protocol +--+ |
| +-------------+ |
| |
+-------------------------------------------+
+--+
|MN|
+--+
Figure 1 - Split Scenario (MSA == MSP)
G. Giaretta, Ed. Expires December 22, 2005 [Page 6]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
Figure 2 shows the split scenario in case the MSA and the MSP are two
different entities. This might happen if the Mobile Node is far from
its MSA network and is assigned a closer HA to optimize performance
or if the MSA cannot provide any Home Agent and relies on a third
party (i.e. the MSP) to grant mobility service to its users. Notice
that the MSP might be or might not be also the network operator that
is providing network access (i.e. ASP, Access Service Provider).
Mobility Service
Authorizer
+-------------+
| MSA AAA |
| server |
+-------------+
^
|
AAA protocol |
| Mobility Service
| Provider
+--------|----------------------------------+
| V |
| +-------------+ +--+ |
| | MSP AAA | <-------------> |HA| |
| | server | AAA protocol +--+ |
| +-------------+ |
| |
+-------------------------------------------+
+--+
|MN|
+--+
Figure 2 - Split Scenario (MSA != MSP)
The split scenario is the simplest model that can be identified,
since no assumptions about the access network are made. This implies
that the mobility service is bootstrapped independently from the
authentication protocol for network access used (e.g. PANA, EAP). For
this reason, the solution described in this document and developed
for this scenario could also be applied to the integrated access
network deployment model [4], even if it might not be optimized .
G. Giaretta, Ed. Expires December 22, 2005 [Page 7]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
4. Components of the solution
The bootstrapping problem is composed of different sub-problems that
can be solved independently in a modular way. The components
identified and a brief overview of their solution follow.
o HA address discovery. The Mobile Node needs to discover the
address of its Home Agent. The main objective of a bootstrapping
solution is to minimize the data pre-configured on the Mobile
Node. For this reason, the DHAAD defined in [2] may not be
applicable in real deployments since it is required that the
Mobile Node is pre-configured with the home network prefix and it
does not allow an operator to load balance by having Mobile Nodes
dynamically assigned to Home Agents located in different subnets.
This document defines a solution for Home Agent address discovery
that is based on Domain Name Service (DNS), introducing a new DNS
SRV record [5]. The unique information that needs to be pre-
configured on the Mobile Node is the domain name of the MSP.
o IPsec Security Associations setup. MIPv6 requires that a Mobile
Node and its Home Agent share an IPsec SA in order to protect
binding updates and other MIPv6 signaling. This document provides
a solution that is based on IKEv2 and follows what is specified in
[6]. The IKEv2 peer authentication can be performed both using
certificates and using EAP, depending on the network operator's
deployment model.
o HoA assignment. The Mobile Node needs to know its Home Address in
order to bootstrap Mobile IPv6 operation. The Home Address is
assigned by the Home Agent during the IKEv2 exchange (as described
in [6]). The solution defined in this draft also allows the Mobile
Node to auto-configure its Home Address based on stateless auto-
configuration ([20]), Cryptographically Generated Addresses ([9])
or privacy addresses ([10]).
o Authentication and Authorization with MSA. The user must be
authenticated in order for the MSA to grant the service. Moreover,
the mobility service must be explicitly authorized by the MSA
based on the user's profile. These operations are performed in
different ways depending on the credentials used by the Mobile
Node during the IKEv2 peer authentication and on the backend
infrastructure (PKI or AAA).
An optional part of bootstrapping involves providing a way for the
Mobile Node to have its FQDN updated in the DNS with a dynamically
assigned home address. While not all applications will require this
service, many networking applications use the FQDN to obtain an
G. Giaretta, Ed. Expires December 22, 2005 [Page 8]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
address for a node prior to starting IP traffic with it. The solution
defined in this document specifies that the dynamic DNS update is
performed by the Home Agent or through the AAA infrastructure,
depending on the trust relationship in place.
G. Giaretta, Ed. Expires December 22, 2005 [Page 9]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
5. Protocol Operations
This section describes in detail the procedures needed to perform
Mobile IPv6 bootstrapping based on the components identified in the
previous section.
5.1. Home Agent Address Discovery
Once a Mobile Node has obtained network access, it can perform Mobile
IPv6 bootstrapping. For this purpose, the Mobile Node queries the DNS
server to request information on Home Agent service. As mentioned
before in the document, the only information that needs to be auto-
configured on the Mobile Node is the domain name of the Mobility
Service Provider.
The Mobile Node needs to obtain the IP address of the DNS server
before it can send a DNS request. This can be pre-configured on the
Mobile Node or obtained through DHCPv6 from the visited link [11]. In
any case, it is assumed that there is some kind of mechanism by which
the Mobile Node is configured with a DNS server since a DNS server is
needed for many other reasons.
Two options for DNS lookup for a Home Agent address are identified in
this document: DNS lookup by Home Agent Name and DNS lookup by
service name.
While this document specifies a Home Agent Address Discovery solution
based on DNS, when the ASP and the MSP are the same entity DHCP may
be used. See [15] for details.
5.1.1. DNS lookup by Home Agent Name
In this case, the Mobile Node is configured with the Fully Qualified
Domain Name of the Home Agent. As an example, the Mobile Node could
be configured with the name "ha1.example.com", where "example.com" is
the domain name of the MSP granting the mobility service.
The Mobile Node constructs a DNS request, by setting the QNAME to the
name of the Home Agent. The request has QTYPE set to 'AAAA', so that
the DNS server sends the IPv6 address of the Home Agent. Once the DNS
server replies to this query, the Mobile Node knows its Home Agent
address and can run IKEv2 in order to set up an IPsec SA and get a
Home Address.
G. Giaretta, Ed. Expires December 22, 2005 [Page 10]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
Additionally, it could be useful to provide an ability for the Mobile
Node to discover a Home Agent placed in a particular location (e.g.
on the visited link). In order to achieve this, the Mobile Node must
be able to construct a DNS request such that the DNS server will be
able to reply with a Home Agent from the requested location. This can
be accomplished by using a specific naming convention for the FQDNs
of the Home Agents. As an example, an operator might assign the FQDN
"ha.locationA.operator.com" to the Home Agent located in "location A"
and the FQDN "ha.locationB.operator.com" to the Home Agent located in
"location B". If the Mobile Node wants to use a Home Agent located in
"location A", it will set the QNAME to "ha.locationA.operator.com" in
the DNS request.
5.1.2. DNS lookup by service name
RFC 2782 [5] defines the service resource record (SRV RR), that
allows an operator to use several servers for a single domain, to
move services from host to host, and to designate some hosts as
primary servers for a service and others as backups. Clients ask for
a specific service/protocol for a specific domain and get back the
names of any available servers.
RFC 2782 [5] describes also the policies to choose a service agent
based on the preference and weight values. The DNS SRV record may
contain the preference and weight values for multiple Home Agents
available to the Mobile Node in addition to the Home Agent FQDNs. If
multiple Home Agents are available in the DNS SRV record then Mobile
Node is responsible for processing the information as per policy and
for picking one Home Agent. If the Home Agent of choice does not
respond for some reason or the IKEv2 authentication fails, the Mobile
Node SHOULD try other Home Agents on the list.
The service name for Mobile IPv6 Home Agent service as required by
RFC 2782 is "mip6" and the protocol name is "ipv6". Note that a
transport name cannot be used here because Mobile IPv6 does not run
over a transport protocol.
The SRV RR has a DNS type code of 33. As an example, the Mobile
constructs a request with QNAME set to "mip6.example.com" and QTYPE
to SRV. The reply contains the FQDNs of one or more servers, that can
then be resolved in a separate DNS transaction to the IP addresses.
However, it is RECOMMENDED that the DNS server also return the IP
addresses of the Home Agents in AAAA records as part of the
additional data section in order to avoid requiring an additional DNS
round trip to resolve the FQDNs, if there is room in the SRV reply.
G. Giaretta, Ed. Expires December 22, 2005 [Page 11]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
5.2. IPsec Security Associations setup
As soon as the Mobile Node has discovered the Home Agent Address, it
establishes an IPsec Security Association with the Home Agent itself
through IKEv2. The detailed description of this procedure is provided
in [6].
The IKEv2 Mobile Node to Home Agent authentication can be performed
using either IKEv2 public key signatures or the Extensible
Authentication Protocol (EAP). The details about how IKEv2
authentication is done are described in [6] and [7]. Choice of an
IKEv2 peer authentication method depends on the deployment. However,
IKEv2 restricts the Home Agent to Mobile Node authentication to use
public key signature based authentication.
5.3. Home Address assignment
Home Address assignment is performed during the IKEv2 exchange. The
Home Address can be assigned directly by the Home Agent or can be
auto-configured by the Mobile Node.
5.3.1. Home Address assignment by the Home Agent
When the Mobile Node runs IKEv2 with its Home Agent, it can request a
HoA through the Configuration Payload in the IKE_AUTH exchange by
including an INTERNAL_IP6_ADDRESS attribute. When the Home Agent
processes the message, it allocates a HoA and sends it a CFG_REPLY
message. The Home Agent could consult a DHCP server on the home link
for the actual home address allocation. This is explained in detail
in [6].
5.3.2. Home Address auto-configuration by the Mobile Node
With the type of assignment described in the previous section, the
Home Address cannot be generated based on Cryptographically Generated
Addresses (CGAs) [9] or based on the privacy extensions for stateless
autoconfiguration [10]. However, the Mobile Node might want to have
an auto-configured HoA based on these mechanisms. It is worthwhile to
mention that the auto-configuration procedure described in this
section cannot be used in some possible deployment, since the Home
Agents might be provisioned with pools of allowed Home Addresses.
In the simplest case, the Mobile Node is provided with a pre-
configured home prefix and home prefix length. In this case the
Mobile Node creates a Home Address based on the pre-configured prefix
G. Giaretta, Ed. Expires December 22, 2005 [Page 12]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
and sends it to the Home Agent including an INTERNAL_IP6_ADDRESS
attribute in a Configuration Payload of type CFG_REQUEST. If the Home
Address is valid, the Home Agent replies with a CFG_REPLY, including
an INTERNAL_IP6_ADDRESS with the same address. If the Home Address
provided by the Mobile Node is not valid, the Home Agent assigns a
different Home Address including an INTERNAL_IP6_ADDRESS attribute
with a new value. According to [7] the Mobile Node MUST use the
address sent by the Home Agent. Later, if the Mobile Node wants to
use an auto-configured Home Address (e.g. based on CGA), it can run
Mobile Prefix Discovery, obtain a prefix, auto-configure a new Home
Address and then perform a new CREATE_CHILD_SA exchange.
If the Mobile Node is not provided with a pre-configured Home Prefix,
the Mobile cannot simply propose an auto-configured HoA in the
Configuration Payload since the Mobile Node does not know the home
prefix before the start of the IKEv2 exchange. The Mobile Node must
obtain the home prefix and the home prefix length before it can
configure a home address.
One simple solution would be for the Mobile Node to just assume that
the prefix length on the home link is 64 bits and extract the home
prefix from the Home Agent's address. The disadvantage with this
solution is that the home prefix cannot be anything other than /64.
Moreover, this ties the prefix on the home link and the Home Agent's
address, but, in general, a Home Agent with a particular address
should be able to serve a number of prefixes on the home link, not
just the prefix from which its address is configured.
Another solution would be for the Mobile Node to assume that the
prefix length on the home link is 64 bits and send its interface
identifier to the Home Agent in the IP6_INTERNAL_ADDRESS attribute
within the CFG_REQ payload. Even though this approach does not tie
the prefix on the home link and the Home Agent's address, it still
requires that the home prefix length is 64 bits.
For this reason the Mobile Node needs to obtain the home link
prefixes through the IKEv2 exchange. In the Configuration Payload
during the IKE_AUTH exchange, the Mobile Node includes the
MIP6_HOME_PREFIX attribute in the CFG_REQUEST message. The Home
Agent, when it processes this message, should include in the
CFG_REPLY payload prefix information for one prefix on the home link.
This prefix information includes the prefix length (see section 8.2).
The Mobile Node auto-configures a Home Address from the prefix
returned in the CFG_REPLY message and runs a CREATE_CHILD_SA exchange
to create security associations for the new Home Address.
G. Giaretta, Ed. Expires December 22, 2005 [Page 13]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
As mentioned before in this document, there are deployments where
auto-configuration of the Home Address cannot be used. In this case,
when the Home Agent receives a CFG_REQUEST including a
MIP6_HOME_PREFIX attribute, in the subsequent IKE response it
includes a Notify Payload type "USE_ASSIGNED_HoA" and the related
Home Address in a INTERNAL_IP6_ADDRESS attribute. If the Mobile Node
gets a "USE_ASSIGNED_HoA" Notify Payload in response to the
Configuration Payload containing the MIP6_HOME_PREFIX attribute, it
looks for an INTERNAL_IP6_ADDRESS attribute and MUST use the address
contained in it in the subsequent CREATE_CHILD_SA exchange.
When the Home Agent receives a Binding Update for the Mobile Node, it
performs proxy DAD for the auto-configured Home Address. If DAD
fails, the Home Agent rejects the Binding Update. If the Mobile Node
receives a Binding Acknowledgement with status 134 (DAD failed), it
MUST stop using the current Home Address, configure a new HoA, and
then run IKEv2 CREATE_CHILD_SA exchange to create security
associations based on the new HoA. The Mobile Node does not need to
run IKE_INIT and IKE_AUTH exchanges again. Once the necessary
security associations are created, the Mobile Node sends a Binding
Update for the new Home Address.
It is worth noting that with this mechanism, the prefix information
carried in MIP6_HOME_PREFIX attribute includes only one prefix and
does not carry all the information that is typically present when
received through a IPv6 router advertisement. Mobile Prefix
Discovery, specified in RFC 3775 [2], is the mechanism through which
the Mobile Node can get all prefixes on the home link and all related
information. That means that MIP6_HOME_PREFIX attribute is only used
for Home Address auto-configuration and does not replace the usage of
Mobile Prefix Discovery for the purposes detailed in RFC 3775.
5.4. Authorization and Authentication with MSA
In a scenario where the Home Agent is discovered dynamically by the
Mobile Node, it is very likely that the Home Agent is not able to
verify by its own the credentials provided by the Mobile Node during
the IKEv2 exchange. Moreover, the mobility service needs to be
explicitly authorized based on the user's profile. As an example, the
Home Agent might not be aware if the mobility service can be granted
at a particular time of the day or if the credit of the Mobile Node
is going to expire.
Due to all these reasons, the Home Agent may need to contact the MSA
in order to authenticate the Mobile Node and authorize mobility
G. Giaretta, Ed. Expires December 22, 2005 [Page 14]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
service. This can be accomplished based on a Public Key
Infrastructure if certificates are used and a PKI is deployed by the
MSP and MSA. On the other hand, if the Mobile Node is provided with
other types of credentials, the AAA infrastructure must be used.
The definition of this backend communication is out of the scope of
this document. In [12] a list of goals for such a communication is
provided.
G. Giaretta, Ed. Expires December 22, 2005 [Page 15]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
6. Home Address registration in the DNS
In order that the Mobile Node is reachable through its dynamically
assigned Home Address, the DNS needs to be updated with the new Home
Address. Since applications make use of DNS lookups on FQDN to find a
node, the DNS update is essential for providing IP reachability to
the Mobile Node, which is the main purpose of the Mobile IPv6
protocol. The need of DNS update is not discussed in RFC 3775 since
it assumes that the Mobile Node is provisioned with a static home
address. However, when a dynamic Home Address is assigned to the
Mobile Node, any existing DNS entry becomes invalid and the Mobile
Node becomes unreachable unless a DNS update is performed.
Since the DNS update must be performed securely in order to prevent
attacks or modifications from malicious nodes, the node performing
this update must share a security association with the DNS server.
Having all possible Mobile Nodes sharing a security association with
the DNS servers of the MSP might be cumbersome from an administrative
perspective. Moreover, even if a Mobile Node has a security
association with a DNS server of its MSP, an address authorization
issue comes into the picture. A detailed analysis of possible threats
against DNS update is provided in section 9.5.
Therefore, due to security and administrative reasons, it is
RECOMMENDED that the Home Agent perform DNS entry update for the
Mobile Node. For this purpose the Mobile Node MAY include a new
mobility option, the DNS Update option, with the flag R not set in
the Binding Update. This option is defined in section 8 and includes
the FQDN that needs to be updated. After receiving the Binding
Update, the Home Agent MUST update the DNS entry with the identifier
provided by the Mobile Node and the Home Address included in the Home
Address Option. The procedure for sending a dynamic DNS update
message is specified in [14]. The dynamic DNS update SHOULD be
performed in a secure way; for this reason, the usage of TKEY and
TSEC or DNSSEC is recommended (see section 9.5 for details). As
soon as the Home Agent has updated the DNS, it MUST send a Binding
Acknowledgement message to the Mobile Node including the DNS Update
mobility option with the correct value in the Status field (see
section 8.1).
This procedure can be performed directly by the Home Agent if the
Home Agent has a security association with the domain specified in
the Mobile Node's FQDN.
On the other hand, if the Mobile Node wants to be reachable through a
FQDN that belongs to the MSA, the Home Agent and the DNS server that
must be updated belong to different administrative domain. In this
G. Giaretta, Ed. Expires December 22, 2005 [Page 16]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
case the Home Agent may not share a security association with the DNS
server and the DNS entry update can be performed by the AAA server of
the MSA. In order to accomplish this, the Home Agent sends to the AAA
server the FQDN-HoA pair through the AAA protocol. This message is
proxied by the AAA infrastructure of the MSP and is received by the
AAA server of the MSA. The AAA server of the MSA perform the DNS
update based on [14]. The detailed description of the communication
between Home Agent and AAA is out of the scope of this draft. More
details are provided in [12].
A mechanism to remove stale DNS entries is needed. A DNS entry
becomes stale when the related Home Address is no more used by the
Mobile Node. To remove a DNS entry, the MN includes the DNS Update
mobility option, with the flag R set in the Binding Update. After
receiving the Binding Update, the Home Agent MUST remove the DNS
entry identified by the FQDN provided by the Mobile Node and the Home
Address included in the Home Address Option. The procedure for
sending a dynamic DNS update message is specified in [14]. As
mentioned above, the dynamic DNS update SHOULD be performed in a
secure way; for this reason, the usage of TKEY and TSEC or DNSSEC is
recommended (see section 9.5 for details).
This approach does not work if the Mobile Node stops using the Home
Address without sending a Binding Update message (e.g. in case of
crash). In this case, an additional mechanism to trigger the DNS
entry removal is needed. For this purpose, the Home Agent has a timer
related to the DNS entry of the Mobile Node. This timer is
initialized when the Mobile Node sends a Binding Update with R==0
(i.e. when the MN asks the Home Agent to bind the FQDN to the Home
Address). The initial value of this timer is configurable by the
network operator.
If the Home Agent receives a Binding Update with R==1, it removes the
DNS entry as described in the previous paragraph and removes the
timer associated to that entry. If the timer expires without
receiving a Binding Update with R==1, the HA checks the Binding
Cache. If there is an existing Binding Cache entry for the HoA, the
HA does not remove the DNS entry and re-initialize the timer. If
there is not a Binding Cache entry, it sends a Neighbor Soliciation
message to check if the MN is at home and is using the HoA. If the HA
gets a Neighbor Advertisement message, it does not remove the DNS
entry and re-initialize the timer. If it does not receive a NA, it
removes the DNS entry and the timer associated to it.
G. Giaretta, Ed. Expires December 22, 2005 [Page 17]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
7. Summary of Bootstrapping Protocol Flow
The message flow of the whole bootstrapping procedure when the
dynamic DNS update is performed by the Home Agent is depicted in
Figure 3.
+----+ +----+ +-----+
| MN | | HA | | DNS |
+----+ +----+ +-----+
IKEv2 exchange
(HoA configuration)
<======================>
BU (DNS update option)
----------------------->
DNS update
<------------------->
BU (DNS update option)
<-----------------------
Figure 3 - Dynamic DNS update by the HA
Figure 4 shows the message flow of the whole bootstrapping procedure
when the dynamic DNS update is performed by the AAA server of the
MSA.
G. Giaretta, Ed. Expires December 22, 2005 [Page 18]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
+----+ +----+ +---+ +---+
| MN | | HA | |AAA| |DNS|
+----+ +----+ +---+ +---+
IKEv2 exchange
(HoA configuration)
<======================>
BU (DNS update option)
----------------------->
AAA request
(FQDN, HoA)
<-------------->
DNS update
<----------->
AAA answer
(FQDN, HoA)
<-------------->
BU (DNS update option)
<-----------------------
Figure 4 - Dynamic DNS update by the AAA
Notice that, even in this last case, the Home Agent is always
required to perform a DNS update for the reverse entry, since this is
always performed in the DNS server of the MSP. This is not depicted
in Figure 4.
G. Giaretta, Ed. Expires December 22, 2005 [Page 19]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
8. Option and Attribute Format
8.1. DNS Update mobility option
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Option Type | Option Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Status |R| Reserved | MN identity (FQDN) ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
o Option Type - DNS-UPDATE-TYPE to be defined by IANA
o Option Length - 8 bit unsigned integer indicating the length of
the option excluding the type and length fields
o Status - 8 bit unsigned integer indicating the result of the
dynamic DNS update procedure. This field MUST be set to 0 and
ignored by the receiver when the DNS Update mobility option is
included in a Binding Update message. When the DNS Update mobility
option is included in the Binding Acknowledgement message, values
of the Status field less than 128 indicate that the dynamic DNS
update was performed successfully by the Home Agent. Values
greater than or equal to 128 indicate that the dynamic DNS update
was not completed by the HA. The following Status values are
currently defined:
0 DNS update performed
128 Reason unspecified
129 Administratively prohibited
130 DNS Update Failed
o R flag - if set the MN is requesting the HA to remove the DNS
entry identified by the FQDN specified in this option and the HoA
of the MN. If not set, the MN is requesting the HA to create or
update a DNS entry with its HoA and the FQDN specified in the
option.
o Reserved - these bits are reserved for future purposes and MUST be
set to 0.
G. Giaretta, Ed. Expires December 22, 2005 [Page 20]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
o MN identity - the identity of the Mobile Node to be used by the
Home Agent to send a Dynamic DNS update. It is a variable length
field.
8.2. MIP6_HOME_PREFIX attribute
The MIP6_HOME_PREFIX attribute is included in the IKEv2 CFG_REQUEST
by the Mobile Node to ask the Home Agent for the home prefix and is
included in the CFG_REPLY by the Home Agent to provide the Mobile
Node with home prefix and home prefix length. The format of this
attribute is equal to the format of the Configuration Attributes
defined in [7] and is depicted below.
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
!R| Attribute Type ! Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| home prefix |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Prefix Length |
+-+-+-+-+-+-+-+-+
o Reserved (1 bit) - This bit MUST be set to zero and MUST be
ignored on receipt.
o Attribute Type (7 bits) - A unique identifier for the
MIP6_HOME_PREFIX attribute. To be assigned by IANA.
o Length (2 octets) - Length in octets of Value field (home prefix
and Prefix Length). This is multi-valued and can be 0 or 17.
o Home Prefix (16 octets) - The prefix of the home link through
which the Mobile Node must auto-configure its Home Address.
o Prefix Length (1 octet) - The length of the home prefix specified
in the field Home Prefix.
When the MIP6_HOME_PREFIX attribute is included by the Mobile Node in
the CFG_REQUEST payload, the value of the Length field is 0. On the
other hand, when the MIP6_HOME_PREFIX attribute is included in the
G. Giaretta, Ed. Expires December 22, 2005 [Page 21]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
CFG_REPLY payload by the Home Agent, the value of the Length field is
17 and the attribute contains also the Home Prefix and the Prefix
Length fields.
G. Giaretta, Ed. Expires December 22, 2005 [Page 22]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
9. Security Considerations
9.1. HA Address Discovery
Use of DNS for address discovery carries certain security risks. DNS
transactions in the Internet are typically done without any
authentication of the DNS server by the client or of the client by
the server. There are two risks involved:
1) A legitimate client obtains a bogus Home Agent address from a
bogus DNS server. This is sometimes called a "pharming" attack,
2) An attacking client obtains a legitimate Home Agent address from a
legitimate server.
The risk in Case 1 is mitigated because the Mobile Node is required
to conduct an IKE transaction with the Home Agent prior to performing
a Binding Update to establish Mobile IPv6 service. According to the
IKEv2 specification [7], the responder must present the initiator
with a valid certificate containing the responder's public key, and
the responder to initiator IKE_AUTH message must be protected with an
authenticator calculated using the public key in the certificate.
Thus, an attacker would have to set up both a bogus DNS server and a
bogus Home Agent, and provision the Home Agent with a certificate
that a victim Mobile Node could verify. If the Mobile Node can detect
that the certificate is not trustworthy, the attack will be foiled
when the Mobile Node attempts to set up the IKE SA.
The risk in Case 2 is limited for a single Mobile Node to Home Agent
transaction if the attacker does not possess proper credentials to
authenticate with the Home Agent. The IKE SA establishment will fail
when the attacking Mobile Node attempts to authenticate itself with
the Home Agent. Regardless of whether the Home Agent utilizes EAP or
host-side certificates to authenticate the Mobile Node, the
authentication will fail unless the Mobile Node has valid
credentials.
Another risk exists in Case 2 because the attacker may be attempting
to propagate a DoS attack on the Home Agent. In that case, the
attacker obtains the Home Agent address from the DNS, then propagates
the address to a network of attacking hosts that bombard the Home
Agent with traffic. This attack is not unique to the bootstrapping
solution, however, it is actually a risk that any Mobile IPv6 Home
Agent installation faces. In fact, the risk is faced by any service
in the Internet that distributes a unicast globally routable address
to clients. Since Mobile IPv6 requires that the Mobile Node
communicate through a globally routable unicast address of a Home
G. Giaretta, Ed. Expires December 22, 2005 [Page 23]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
Agent, it is possible that the Home Agent address could be propagated
to an attacker by various means (theft of the Mobile Node, malware
installed on the Mobile Node, evil intent of the Mobile Node owner
him/herself, etc.) even if the home address is manually configured on
the Mobile Node. Consequently, every Mobile IPv6 Home Agent
installation will likely be required to mount anti-DoS measures. Such
measures include overprovisioning of links to and from Home Agents
and of Home Agent processing capacity, vigilant monitoring of traffic
on the Home Agent networks to detect when traffic volume increases
abnormally indicating a possible DoS attack, and hot spares that can
quickly be switched on in the event an attack is mounted on an
operating collection of Home Agents. DoS attacks of moderate
intensity should be foiled during the IKEv2 transaction. IKEv2
implementations are expected to generate their cookies without any
saved state, and to time out cookie generation parameters frequently,
with the timeout value increasing if a DoS attack is suspected. This
should prevent state depletion attacks, and should assure continued
service to legitimate clients until the practical limits on the
network bandwith and processing capacity of the Home Agent network
are reached.
Explicit security measures between the DNS server and host, such
DNSSEC [16] or TSIG/TKEY [17] [18] can mitigate the risk of 1) and
2), but these security measures are not widely deployed on end nodes.
These security measures are not sufficient to protect the Home Agent
address against DoS attack, however, because a node having a
legitimate security association with the DNS server could
nevertheless intentionally or inadvertently cause the Home Agent
address to become the target of DoS.
Security considerations for discovering HA using DHCP are covered in
draft-jang-dhc-haopt-01 [15].
9.2. Home Address Assignment through IKEv2
Mobile IPv6 bootstrapping assigns the home address through the IKEv2
transaction. The Mobile Node can either choose to request an address,
similar to DHCP, or the Mobile Node can request a prefix on the home
link then autoconfigure an address.
RFC 3775 [2] and 3776 [3] require that a Home Agent check
authorization on a home address received during a Binding Update. The
Home Agent MUST set up authorization by linking the home address to
the identity of the IPsec SAs used to authenticate the Binding Update
message. The linking MUST be done either during the IKE_AUTH phase or
CREATE_CHILD_SA phase when the IPsec SAs are constructed.
G. Giaretta, Ed. Expires December 22, 2005 [Page 24]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
If the address is autoconfigured, RFC 3775 requires the Home Agent to
proxy-defend the address on the home link after the Mobile Node
performs the initial Binding Update. Since it is not currently
possible to securely proxy CGAs using SEND, attacks on address
resolution for Neighbor Discovery listed in RFC 3756 are possible on
dynamically assigned home addresses that are proxied by the Home
Agent.
9.3. SA Establishment Using EAP Through IKEv2
Security considerations for authentication of the IKE transaction
using EAP are covered in draft-ietf-mip6-ikev2-ipsec [6].
9.4. Back End Security Between the HA and AAA Server
Some deployments of Mobile IPv6 bootstrapping may use an AAA server
to handle authorization for mobility service. This process has its
own security requirements, but the back end protocol for Home Agent
to AAA server interface is not covered in this draft. Please see
draft-ietf-mip6-aaa-ha-goals [12] for a discussion of this interface.
9.5. Dynamic DNS Update
Mobile IPv6 bootstrapping recommends the Home Agent to update the
Mobile Node's FQDN with a dynamically assigned home address rather
than have the Mobile Node itself do it (see Section 6 above). This
choice was motivated by a concern for preventing redirection-based
flooding attacks (see draft-ietf-mip6-ro-sec [19] for more
information about redirection-based flooding attacks and the role
preventing them played in the design of Mobile IPv6 route
optimization security). Exactly as for route optimization, it is
possible for a node that is the legitimate owner of a DNS FQDN - in
the sense that it has a security association with the DNS server
allowing it to perform dynamic DNS update of its FQDN - to bind its
FQDN to the address of a victim, then redirect large volumes of
traffic at the victim. The attack may be propagated without the
owner's knowledge, for example, if the node is compromised by
malware, or it may be intentional if the node itself is the attacker.
While it is possible to prevent redirection attacks through ingress
filtering on access routers, ISPs have little or no incentive to
deploy ingress filtering. In some cases, if an attack could result in
substantial financial gain, it is even possible that a corrupt ISP
may have an incentive not to deploy ingress filters such as has been
the case for spam. Consequently, the security for dynamic Mobile Node
FQDN update has been assigned to the Home Agent, where active network
administration and vigilant defense measures are more likely to (but
G. Giaretta, Ed. Expires December 22, 2005 [Page 25]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
are not assured of) mitigating problems, and the owner of the Mobile
Node is more likely to detect a problem if it occurs.
If a Home Agent performs dynamic DNS update on behalf of the Mobile
Node directly with the DNS server, the Home Agent MUST have a
security association of some type with the DNS server. The security
association MAY be established either using DNSSEC [16] or TSIG/TKEY
[17][18]. A security association is required even if the DNS server
is in the same administrative domain as the Home Agent. The security
association SHOULD be separate from the security associations used
for other purposes, such as AAA.
In the case where the Mobility Service Provider is different from the
Mobility Service Authorizer, the network administrators may want to
limit the number of cross-administrative domain security
associations. If the Mobile Node's FQDN is in the Mobility Service
Authorizer's domain, since a security association for AAA signaling
involved in mobility service authorization is required in any case,
the Home Agent can send the Mobile Node's FQDN to the AAA server
under the HA-AAA server security association, and the AAA server can
perform the update. In that case, a security association is required
between the AAA server and DNS server for the dynamic DNS update. See
draft-ietf-mip6-aaa-ha-goals [12] for a deeper discussion of the Home
Agent to AAA server interface.
Regardless of whether the AAA server or Home Agent performs DNS
update, the authorization of the Mobile Node to update a FQDN MUST be
checked prior to the performance of the update. It is an
implementation issue as to how authorization is determined.
G. Giaretta, Ed. Expires December 22, 2005 [Page 26]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
10. IANA Considerations
This document defines a new Mobility Option and a new IKEv2
Configuration Attribute Type.
The following values should be assigned:
o from "Mobility Option" namespace ([2]): DNS-UPDATE-TYPE (section
8.1)
o from "IKEv2 Configuration Payload Attribute Types" namespace
([7]): MIP6_HOME_PREFIX attribute (section 8.2)
o from "IKEv2 Notify Payload Error Types" namespace ([7]):
USE_ASSIGNED_HoA error type (section 5.3.2)
G. Giaretta, Ed. Expires December 22, 2005 [Page 27]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
11. Contributors
This contribution is a joint effort of the bootstrapping solution
design team of the MIP6 WG. The contributors include Basavaraj
Patil, Alpesh Patel, Jari Arkko, James Kempf, Yoshihiro Ohba, Gopal
Dommety, Alper Yegin, Junghoon Jee, Vijay Devarapalli, Kuntal
Chowdury, Julien Bournelle.
The design team members can be reached at:
Gerardo Giaretta gerardo.giaretta@tilab.com
Basavaraj Patil basavaraj.patil@nokia.com
Alpesh Patel alpesh@cisco.com
Jari Arkko jari.arkko@kolumbus.fi
James Kempf kempf@docomolabs-usa.com
Yoshihiro Ohba yohba@tari.toshiba.com
Gopal Dommety gdommety@cisco.com
Alper Yegin alper.yegin@samsung.com
Vijay Devarapalli vijayd@iprg.nokia.com
Kuntal Chowdury kchowdury@starentnetworks.com
Junghoon Jee jhjee@etri.re.kr
Julien Bournelle julien.bournelle@int-evry.fr
G. Giaretta, Ed. Expires December 22, 2005 [Page 28]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
12. References
12.1. Normative References
[1] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, March 1997.
[2] Johnson, D., Perkins, C. and J. Arkko, "Mobility Support
in IPv6", RFC 3775, June 2004.
[3] Arkko, J., Devarapalli, V., Dupont, F., "Using IPsec to
Protect Mobile IPv6 Signaling between Mobile Nodes and
Home Agents", RFC 3776, June 2004
[4] Patel, A., "Problem Statement for bootstrapping Mobile IPv6",
Internet-Draft draft-ietf-mip6-bootstrap-ps-02, March 2005.
[5] Gulbrandsen, A., Vixie, P. and L. Esibov, "A DNS RR for
specifying the location of services (DNS SRV)", RFC 2782,
February 2000.
[6] Devarapalli, V., " Mobile IPv6 Operation with IKEv2 and the
revised IPsec Architecture", Internet-Draft draft-ietf-mip6-
ikev2-ipsec-01, February 2005.
[7] Kaufman, C., "Internet Key Exchange (IKEv2) Protocol",
Internet-Draft draft-ietf-ipsec-ikev2-17, October 2004
12.2. Informative References
[8] Manner, J., Kojo, M. "Mobility Related Terminology", RFC 3753,
June 2004.
[9] Aura, T., "Cryptographically Generated Addresses (CGA)", RFC
3972, March 2005.
[10] Narten, T., Draves, R., Krishnan, S., "Privacy Extensions for
Stateless Address Autoconfiguration in IPv6", Internet-Draft
draft-ietf-ipv6-privacy-addrs-v2-03, April 2005.
[11] Droms, R., Ed., "DNS Configuration options for Dynamic Host
Configuration Protocol for IPv6 (DHCPv6)", RFC 3646, December
2003.
[12] Giaretta, G., Ed. "Goals for AAA-HA interface", Internet-Draft
draft-ietf-mip6-aaa-ha-goals-00, April 2005.
G. Giaretta, Ed. Expires December 22, 2005 [Page 29]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
[13] Koodli, R., Devarapalli, V., Perkins, C., Flinck, H.,
"Solutions for IP Address Location Privacy in the presence of
IP Mobility", Internet-Draft, draft-koodli-mip6-location-
privacy-solutions-00, February 2005.
[14] P. Vixie, Ed., S. Thomson, Y. Rekhter, and J. Bound. "Dynamic
Updates in the Domain Name System (DNS UPDATE)", RFC 2136,
April 1997.
[15] Jang, H.J., Yegin, A., Choi, J., "DHCP Option for Home Agent
Discovery in MIPv6", Internet-Draft, draft-jang-dhc-haopt-01,
April 2005.
[16] Arends, R., Austein, R., Larson, M., Massey, D., Rose, S., "DNS
Security Introduction and Requirements", RFC 4033, March 2005.
[17] Vixie, P., Gudmundsson, O., Eastlake 3rd, D., Wellington, B.,
"Secret Key Transaction Authentication for DNS (TSIG)", RFC
2845, May 2000.
[18] Eastlake 3rd, D., " Secret Key Establishment for DNS (TKEY
RR)", RFC 2930, September 2000.
[19] Nikander, P., Arkko, J., Aura, T., Montenegro, G., Nordmark,
E., "Mobile IP version 6 Route Optimization Security Design
Background", Internet-Draft, draft-ietf-mip6-ro-sec-02, October
2004.
[20] Narten, T., Nordmark, E., Simpson, W., Soliman, H., "Neighbor
Discovery for IP version 6 (IPv6)"`, Internet-Draft, draft-
ietf-ipv6-2461bis-03, May 2005.
G. Giaretta, Ed. Expires December 22, 2005 [Page 30]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
Authors' Addresses
Gerardo Giaretta
Telecom Italia Lab
via Reiss Romoli 274
10148 Torino
Italy
Phone: +39 011 228 6904
Email: gerardo.giaretta@tilab.com
James Kempf
DoCoMo Labs USA
181 Metro Drive
Suite 300
San Jose, CA, 95110
USA
Phone: +1 408 451 4711
Email: kempf@docomolabs-usa.com
Vijay Devarapalli
Nokia Research Center
313 Fairchild Drive
Mountain View, CA 94043
USA
Email: vijay.devarapalli@nokia.com
G. Giaretta, Ed. Expires December 22, 2005 [Page 31]
Internet-Draft MIPv6 bootstrapping in split scenario June 2005
Intellectual Property Statement
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org
Disclaimer of Validity
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Copyright Statement
Copyright (C) The Internet Society (2005).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
Acknowledgment
Funding for the RFC Editor function is currently provided by the
Internet Society.
G. Giaretta, Ed. Expires December 22, 2005 [Page 32]
| PAFTECH AB 2003-2026 | 2026-04-22 22:40:31 |