One document matched: draft-ietf-l2vpn-vpls-mib-04.txt
Differences from draft-ietf-l2vpn-vpls-mib-03.txt
Internet Draft Thomas D. Nadeau (Ed.)
Intended status: Standards Track BT
Expires: Dec 2010
A S Kiran Koushik (Ed.)
Cisco Systems, Inc.
Rohit Mediratta (Ed.)
Alcatel-Lucent
Virtual Private Lan Services (VPLS) Management Information Base
draft-ietf-l2vpn-vpls-mib-04.txt
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on December 07, 2010.
Abstract
This memo defines an experimental portion of the Management
Information Base for use with network management protocols in the
Internet community. In particular, it describes managed objects
for modeling of Virtual Private LAN services. It needs to be used
in conjunction with Pseudo Wire (PW) Management Information Base
[RFC5601].
Table of Contents
Abstract........................................................1
1 Introduction................................................2
L2 VPN Working Group Expires Dec 2010 [Page 1]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
2 Terminology..................................................4
3 The Internet-Standard Management Framework...................4
4 VPLS MIB Module Architecture.................................4
4.1 VPLS-GENERIC-DRAFT-01-MIB Module Usage......................4
4.2 VPLS-LDP-DRAFT-01-MIB Module Usage..........................5
4.3 VPLS-BGP-DRAFT-01-MIB Module Usage..........................5
4.4 Relations to other MIB modules..............................5
5 Example of the VPLS MIB modules usage........................6
6 Object definitions...........................................6
6.1 VPLS-GENERIC-DRAFT-01-MIB...................................7
6.2 VPLS-LDP-DRAFT-01-MIB Object definitions..................27
6.3 VPLS-BGP-DRAFT-01-MIB Object definitions...................33
7. Security Considerations.....................................41
8. IANA Considerations.........................................41
9. References..................................................42
9.1 Normative References.......................................42
9.2 Informative References.....................................42
10 Acknowledgement.............................................43
11 Authors' Addresses..........................................43
12 Full Copyright Statement....................................45
1 Introduction
This memo defines a portion of the Management Information Base
(MIB) for use with network management protocols in the Internet
community. In particular, it defines a MIB module that can be
used to manage VPLS(Virtual Private LAN Services for transmission
over a packet Switched Network (PSN) using LDP [RFC4762] or
BGP[RFC4761] signalling. This MIB module provides generic
management of VPLS services as defined by the IETF L2VPN Working
Group.
Comments should be made directly to the L2VPN mailing list at
l2vpn@ietf.org.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL
NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
[RFC2119].
Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL
L2 VPN Working Group Expires Dec 2010 [Page 2]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
RFC-2119 [RFC2119].
L2 VPN Working Group Expires Dec 2010 [Page 3]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
2 Terminology
This document adopts the definitions, acronyms and mechanisms
described in [RFC3985]. Unless otherwise stated, the mechanisms of
[RFC3985] apply and will not be re-described here.
3 The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7
of RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store,
termed the Management Information Base or MIB. MIB objects are
generally accessed through the Simple Network Management Protocol
(SNMP). Objects in the MIB are defined using the mechanisms
defined in the Structure of Management Information (SMI). This
memo specifies a MIB module that is compliant to the SMIv2, which
is described in STD 58,[RFC2578], STD 58, [RFC2579] and STD 58,
[RFC2580].
4 VPLS MIB Module Architecture
The MIB structure for defining a VPLS service is composed from four
types of MIB modules.
L2 VPN Working Group Expires Dec 2010 [Page 4]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
The first type is the VPLS-GENERIC-DRAFT-01-MIB module, which
configures general parameters of the VPLS service that are common
to all types of emulated services.
The second type is the VPLS-LDP-DRAFT-01-MIB module, which
configures VPLS-LDP[RFC4762] specific parameters of the
VPLS service.
The third type is the VPLS-BGP-DRAFT-01-MIB module, which configures
VPLS-BGP[RFC4761] specific parameters of the
VPLS service.
The fourth type of modules are service-specific modules, which are
defined in other documents.
-------- -----------------
PW Mapping | | | |
-----> | PW-MIB |-->|PW-ENET/MPLS-MIB |
__________ / | | | |
| | / -------- -----------------
| VPLS MIB | / ------------
| |----------------------> | |
----------- MAC addr. mapping using | BRIDGE-MIB |
[SNMP-CONTEXT-MAP-MIB] | |
------------
4.1 VPLS-GENERIC-DRAFT-01-MIB Module Usage
An entry in the vplsConfigTable MUST exist for a VPLS service.
This table holds generic parameters which apply to a VPLS service
which can be signalled via LDP or BGP.
A conceptual row can be created in the vplsConfigTable in one of
the following ways:
1) The operator creates a row in the vplsConfigTable when
configuring the node for a new service. This mode MUST be
supported by the agent, and MUST be used when creating a
manually assigned VPLS service.
2) The agent MAY create a row in the vplsConfigTable automatically
due to some auto discovery application, or based on
configuration that is done through non-SNMP applications.
This mode is OPTIONAL.
An entry in the vplsPwBindTable MUST exist for a VPLS service.
This binding table links one VPLS service with one or many
L2 VPN Working Group Expires Dec 2010 [Page 5]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
pseudo wires (defined in [RFC5601]). The pseudo wire may
be used as a spoke or a mesh based on the parameters defined
in this table.
An entry in the vplsBgpAdConfigTable MUST exist if
Auto-discovery has been enabled on this service. This table
stores the information required for auto-discovery.
An entry in the vplsBgpRteTargetTable MUST exist if auto-discovery
has been configured on this service. One service can import
and export multiple Route targets.
The agent than creates the rows in the (locally supported)
performance tables and reverse mapping tables in
VPLS-GENERIC-DRAFT-01-MIB module.
4.2 VPLS-LDP-DRAFT-01-MIB Module Usage
An entry in the vplsLdpConfigTable MUST be created by the agent
for a VPLS service signalled using LDP.
4.3 VPLS-BGP-DRAFT-01-MIB Module Usage
An entry in the vplsBgpConfigTable MUST be created by the agent
for a VPLS service signalled using BGP.
4.4 Relations to other MIB modules
- The vplsPwBindTable links the VPLS entry to various entries in
the [RFC5601]
- The association of MAC addresses to VPLS entries is possible
by adding a turnstile function to interpret the entries in
[SNMP-CONTEXT-MAP-MIB]. In [SNMP-CONTEXT-MAP-MIB] there is
a mapping between the vacmContextName[RFC3415] to
dot1dBasePort[RFC4188] and vplsConfigIndex. This mapping can
be used to map the vplsConfigIndex to a dot1dBasePort
in the BRIDGE-MIB. This resulting value of dot1dBasePort
can be used to access corresponding MAC addresses that belong
to a particular vplsConfigIndex.
- Unless all the necessary entries in the applicable tables have
been created and all the parameters have been consistently
configured in those tables, signaling cannot be performed
from the local node, and the ??? should report 'notPresent'.
- Statistics can be gathered from the [RFC5601] - TBD
L2 VPN Working Group Expires Dec 2010 [Page 6]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
5 Example of the VPLS MIB modules usage
In this section we provide an example of using the MIB objects
described in section 7 to set up a VPLS service over MPLS. While
this example is not meant to illustrate every permutation of the
MIB, it is intended as an aid to understanding some of the key
concepts. It is meant to be read after going through the MIB
itself.
In the VPLS-GENERIC-DRAFT-01-MIB module:
In vplsConfigTable:
{
vplsConfigIndex 10,
vplsConfigName "VPLS-A"
vplsConfigAdminStatus 1(up),
vplsConfigMacLearning 1(true),
vplsConfigDiscardUnknownDest 2(false),
vplsConfigMacAging 1(true),
vplsConfigVpnId "100:10"
vplsConfigRowStatus 1(active)
}
In vplsStatusTable:
{
vplsStatusOperStatus 1(up),
}
In the VPLS-LDP-DRAFT-01-MIB module:
In vplsLdpConfigTable:
{
vplsLdpConfigMacAddrWithdraw 1(true),
}
In vplsLdpPwBindTable:
{
vplsLdpPwBindType 1(mesh),
vplsLdpPwBindMacAddressLimit 100
}
6 Object definitions
6.1 VPLS-GENERIC-DRAFT-01-MIB
This MIB module makes references to the following documents.
L2 VPN Working Group Expires Dec 2010 [Page 7]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
[RFC2578], [RFC2579], [RFC2580], [RFC3411],
[RFC2863], [RFC4001], [RFC4265] and [RFC3813].
VPLS-GENERIC-DRAFT-01-MIB DEFINITIONS ::= BEGIN
IMPORTS
NOTIFICATION-TYPE, MODULE-IDENTITY, OBJECT-TYPE,
Unsigned32, Counter32, transmission
FROM SNMPv2-SMI -- RFC2578
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF -- RFC2580
TruthValue, RowStatus, StorageType
FROM SNMPv2-TC -- RFC2579
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB -- RFC3411
PwIndexType
FROM PW-TC-STD-MIB
VPNIdOrZero
FROM VPN-TC-STD-MIB -- RFC4265
-- Vpls BGP Autodiscovery specific Textual Convention
VplsBgpRouteDistinguisher ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Syntax for a route distinguisher. For a complete
definition of a route distinguisher, see [RFC4364].
For more details on use of a route distinguisher
for a VPLS service, see [RFC4761]"
REFERENCE
"[RFC4364]"
SYNTAX OCTET STRING(SIZE (0..256))
VplsBgpRouteTarget ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Syntax for a route target. For a complete
definition of a route target, see [RFC4364]."
REFERENCE
"[RFC4364]"
SYNTAX OCTET STRING(SIZE (0..256))
VplsBgpRouteTargetType ::= TEXTUAL-CONVENTION
STATUS current
L2 VPN Working Group Expires Dec 2010 [Page 8]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
DESCRIPTION
"Used to define the type of a route target usage.
Route targets can be specified to be imported,
exported, or both. For a complete definition of a
route target, see [RFC4364]."
REFERENCE
"[RFC4364]"
SYNTAX INTEGER { import(1), export(2), both(3) }
;
vplsGenericDraft01MIB MODULE-IDENTITY
LAST-UPDATED "200608301200Z" -- 30 Aug 2006 12:00:00 GMT
ORGANIZATION "Layer 2 Virtual Private Networks (L2VPN)
Working Group"
CONTACT-INFO
"
Thomas D. Nadeau
Email: tnadeau@cisco.com
The L2VPN Working Group (email distribution l2vpn@ietf.org,
http://www.ietf.org/html.charters/l2vpn-charter.html)
"
DESCRIPTION
"Copyright (C) The IETF Trust (2010). The initial
version of this MIB module was published in RFC XXXX.
-- RFC Editor: Please replace XXXX with RFC number & remove
-- this note.
For full legal notices see the RFC itself or see:
http://www.ietf.org/copyrights/ianamib.html
This MIB module contains generic managed object definitions
for Virtual Private LAN Services as in [RFC4762] and
[RFC4761]
This MIB module enables the use of any underlying PseudoWire
network."
-- Revision history.
REVISION
"200608301200Z" -- 30 August 2006 12:00:00 GMT
DESCRIPTION
"Changes from previous version:
1) Moved LDP Specific information to VPLS-LDP-DRAFT-01-MIB
2) Created the vplsStatusTable to store status information.
3)
L2 VPN Working Group Expires Dec 2010 [Page 9]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
"
REVISION
"200606041200Z" -- 4 June 2006 12:00:00 GMT
DESCRIPTION "Initial version published as part of RFC YYYY."
-- RFC Editor: please replace YYYY with IANA assigned value, and
-- delete this note.
::= { transmission XXXX }
-- RFC Editor: please replace XXXX with IANA assigne value, and
-- delete this note.
-- Top-level components of this MIB.
-- Notifications
vplsNotifications OBJECT IDENTIFIER
::= { vplsGenericDraft01MIB 0 }
-- Tables, Scalars
vplsObjects OBJECT IDENTIFIER
::= { vplsGenericDraft01MIB 1 }
-- Conformance
vplsConformance OBJECT IDENTIFIER
::= { vplsGenericDraft01MIB 2 }
-- PW Virtual Connection Table
vplsConfigIndexNext OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains an appropriate value to be used
for vplsConfigIndex when creating entries in the
vplsConfigTable. The value 0 indicates that no
unassigned entries are available. To obtain the
value of vplsConfigIndex for a new entry in the
vplsConfigTable, the manager issues a management
protocol retrieval operation to obtain the current
value of vplsConfigIndex. After each retrieval
operation, the agent should modify the value to
reflect the next unassigned index. After a manager
retrieves a value the agent will determine through
its local policy when this index value will be made
available for reuse."
::= { vplsObjects 1 }
L2 VPN Working Group Expires Dec 2010 [Page 10]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
vplsConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF VplsConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies information for configuring
and monitoring Virtual Private Lan Services(VPLS).
"
::= { vplsObjects 2 }
vplsConfigEntry OBJECT-TYPE
SYNTAX VplsConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in this table represents a Virtual Private Lan
Service(VPLS) in a packet network. It is indexed by
vplsConfigIndex, which uniquely identifies a single VPLS.
A row is created by the operator or by the agent if a
VPLS service is created by non-SNMP application or
due to autodiscovery process.
None of the read-create objects values can be
changed when vplsConfigRowStatus is in the active(1)
state. Changes are allowed when the vplsConfigRowStatus
is in notInService(2) or notReady(3) states only.
If the operator need to change one of the values
for an active row the vplsConfigRowStatus should be
first changed to notInService(2), the objects may
be changed now, and later to active(1) in order to
re-initiate the signaling process with the new
values in effect.
"
INDEX { vplsConfigIndex }
::= { vplsConfigTable 1 }
VplsConfigEntry ::=
SEQUENCE {
vplsConfigIndex Unsigned32,
vplsConfigName SnmpAdminString,
vplsConfigDescr SnmpAdminString,
vplsConfigAdminStatus INTEGER,
vplsConfigMacLearning TruthValue,
vplsConfigDiscardUnknownDest TruthValue,
vplsConfigMacAging TruthValue,
vplsConfigFwdFullHighWatermark Unsigned32,
vplsConfigFwdFullLowWatermark Unsigned32,
L2 VPN Working Group Expires Dec 2010 [Page 11]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
vplsConfigRowStatus RowStatus,
vplsConfigMtu Unsigned32,
vplsConfigVpnId VPNIdOrZero,
vplsConfigServiceType INTEGER,
vplsConfigStorageType StorageType
}
vplsConfigIndex OBJECT-TYPE
SYNTAX Unsigned32 (1.. 2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Unique index for the conceptual row identifying
a VPLS service."
::= { vplsConfigEntry 1 }
vplsConfigName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A textual name of the VPLS.
If there is no local name, or this object is
otherwise not applicable, then this object MUST
contain a zero-length octet string."
DEFVAL { "" }
::= { vplsConfigEntry 2 }
vplsConfigDescr OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A textual string containing information about the
VPLS service. If there is no information for this VPLS
service, then this object MUST contain a zero-length
octet string."
DEFVAL { "" }
::= { vplsConfigEntry 3 }
vplsConfigAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2),
testing(3) -- in some test mode
}
MAX-ACCESS read-create
L2 VPN Working Group Expires Dec 2010 [Page 12]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
STATUS current
DESCRIPTION
"The desired administrative state of the VPLS
service. If the administrative status of the
Vpls service is changed to enable then this
service is able to utilize the pseudo wire to
perform the tasks of a VPLS service.
The testing(3) state indicates that no operational
packets can be passed. "
DEFVAL { down }
::= { vplsConfigEntry 4 }
vplsConfigMacLearning OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies if MAC Learning is enabled
in this service. If this object is true then Mac
Learning is enabled. If false, then Mac Learning is
disabled."
DEFVAL { true }
::= { vplsConfigEntry 6 }
vplsConfigDiscardUnknownDest OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the value of this object is 'true', then frames
received with an unknown destination MAC are discarded
in this VPLS. If 'false', then the packets are
processed."
DEFVAL { false }
::= { vplsConfigEntry 7 }
vplsConfigMacAging OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the value of this object is 'true'
then the MAC ageing process is enabled in
this VPLS. If 'false', then the MAC ageing process
is disabled"
DEFVAL { true }
::= { vplsConfigEntry 8 }
L2 VPN Working Group Expires Dec 2010 [Page 13]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
vplsConfigFwdFullHighWatermark OBJECT-TYPE
SYNTAX Unsigned32 (0..100)
UNITS "percentage"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the utilization of the
forwarding database for this VPLS instance at
which the vplsFwdFullAlarmRaised notification
will be sent."
DEFVAL { 95 }
::= { vplsConfigEntry 10 }
vplsConfigFwdFullLowWatermark OBJECT-TYPE
SYNTAX Unsigned32 (0..100)
UNITS "percentage"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the utilization of the
forwarding database for this VPLS instance
at which the vplsFwdFullAlarmCleared
notification will be sent."
DEFVAL { 90 }
::= { vplsConfigEntry 11 }
vplsConfigRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"For creating, modifying, and deleting this row.
None of the read-create objects in the
conceptual rows may be changed when this
object is in the active(1) state."
::= { vplsConfigEntry 12 }
vplsConfigMtu OBJECT-TYPE
SYNTAX Unsigned32 (64..1518)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object specifies the MTU of this
vpls instance."
DEFVAL { 1518 }
::= { vplsConfigEntry 13 }
vplsConfigVpnId OBJECT-TYPE
L2 VPN Working Group Expires Dec 2010 [Page 14]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
SYNTAX VPNIdOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This objects indicates the IEEE 802-1990
VPN ID of the associated VPLS service."
-- Ed note: Should we import the VPNIdOrZero TC or
-- define a new TC?
::= { vplsConfigEntry 14 }
vplsConfigServiceType OBJECT-TYPE
SYNTAX INTEGER {
vlan (1),
ethernet (2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object specifies the type of
service emulated by this vpls instance."
DEFVAL { vlan }
::= { vplsConfigEntry 15 }
vplsConfigStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable indicates the storage type for this row."
DEFVAL { volatile }
::= { vplsConfigEntry 16 }
-- VPLS Status table
vplsStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF VplsStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides information for monitoring
Virtual Private Lan Services(VPLS).
"
::= { vplsObjects 3 }
vplsStatusEntry OBJECT-TYPE
SYNTAX VplsStatusEntry
MAX-ACCESS not-accessible
STATUS current
L2 VPN Working Group Expires Dec 2010 [Page 15]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
DESCRIPTION
"A row in this table represents a Virtual Private Lan
Service(VPLS) in a packet network. It is indexed by
vplsConfigIndex, which uniquely identifies a single VPLS.
A row in this table is automatically created by the agent
when a VPLS service is configured.
"
INDEX { vplsConfigIndex }
::= { vplsStatusTable 1 }
VplsStatusEntry ::=
SEQUENCE {
vplsStatusOperStatus INTEGER,
vplsStatusPeerCount Counter32
}
vplsStatusOperStatus OBJECT-TYPE
SYNTAX INTEGER {
other(0),
up(1),
down(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current operational state of this VPLS Service."
::= { vplsStatusEntry 1 }
vplsStatusPeerCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This objects specifies the number of peers
present in this vpls instance."
::= { vplsStatusEntry 2 }
-- VPLS PW Binding Table
vplsPwBindTable OBJECT-TYPE
SYNTAX SEQUENCE OF VplsPwBindEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides an association between a
VPLS service and the corresponding Pseudo
L2 VPN Working Group Expires Dec 2010 [Page 16]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
Wires. A service can have more than one Pseudo
Wire association. Pseudo Wires are defined in
the pwTable"
::= { vplsObjects 4 }
vplsPwBindEntry OBJECT-TYPE
SYNTAX VplsPwBindEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each row represents an association between a
VPLS instance and one or more Pseudo Wires
defined in the pwTable. Each index is unique
in describing an entry in this table. However
both indexes are required to define the one
to many association of service to
pseudowire."
INDEX { vplsConfigIndex, vplsPwBindIndex }
::= { vplsPwBindTable 1 }
VplsPwBindEntry ::=
SEQUENCE {
vplsPwBindConfigType INTEGER,
vplsPwBindType INTEGER,
vplsPwBindRowStatus RowStatus,
vplsPwBindStorageType StorageType
}
vplsPwBindConfigType OBJECT-TYPE
SYNTAX INTEGER {
manual (1),
autodiscovery (2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object indicates
whether the Pseudo Wire binding was created
manually or via autodiscovery.
The value of this object must be
specifed when the row is created and cannot
be changed while the row status is active(1)"
::= { vplsPwBindEntry 1 }
vplsPwBindType OBJECT-TYPE
SYNTAX INTEGER {
mesh (1),
L2 VPN Working Group Expires Dec 2010 [Page 17]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
spoke (2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object indicates
whether the Pseudo Wire binding is of
type mesh or spoke.
The value of this object must be
specifed when the row is created and cannot
be changed while the row status is active(1)"
::= { vplsPwBindEntry 2 }
vplsPwBindRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"For creating, modifying, and deleting this row.
None of the read-create objects in the
conceptual rows may be changed when this
object is in the active(1) state"
::= { vplsPwBindEntry 3 }
vplsPwBindStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable indicates the storage type for this row."
DEFVAL { volatile }
::= { vplsPwBindEntry 4 }
-- vplsBgpADConfigTable
vplsBgpADConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF VplsBgpADEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies information for configuring
BGP Auto-discovery parameters for a given Vpls service.
"
::= { vplsObjects 5 }
vplsBgpADConfigEntry OBJECT-TYPE
SYNTAX VplsBgpADConfigEntry
L2 VPN Working Group Expires Dec 2010 [Page 18]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in this table represents BGP based autodiscovery
is in use for this instance of Vpls.
A row in this table is indexed by vplsConfigIndex, which
uniquely identifies a single VPLS.
None of the read-create objects can be changed when
vplsBGPADConfigRowStatus is in active(1) state. Changes
are allowed when the vplsBGPADConfigRowStatus is in
notInService(2) or notReady(3) states only.
If the operator need to change one of the values
for an active row the vplsConfigRowStatus should be
first changed to notInService(2), the objects may
be changed now, and later to active(1) in order to
re-initiate the signaling process with the new
values in effect.
"
INDEX { vplsConfigIndex }
::= { vplsBgpADConfigTable 1 }
VplsBgpADConfigEntry ::=
SEQUENCE {
vplsBgpADConfigRouteDistinguisher VplsBgpRouteDistinguisher,
vplsBgpADConfigPrefix Unsigned32,
vplsBgpADConfigVplsId VplsBgpRouteDistinguisher,
vplsBgpADConfigRowStatus RowStatus
}
vplsBgpADConfigRouteDistinguisher OBJECT-TYPE
SYNTAX VplsBgpRouteDistinguisher
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" The route distinguisher for this VPLS. See [RFC4364]
for a complete definition of a route distinguisher.
for more details on use of a route distinguisher
for a VPLS service, see [RFC4761]
"
::= { vplsBgpADConfigEntry 1 }
vplsBgpADConfigPrefix OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" In case of auto-discovery the default prefix advertised
is the ip address of the loopback. In case the user wants
L2 VPN Working Group Expires Dec 2010 [Page 19]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
to override the loopback address, vplsBgpADConfigPrefix
should be set. When this value if non-zero it is used
as the advertised IP address in the NLRI.
"
DEFVAL { 0 }
::= { vplsBgpADConfigEntry 2 }
vplsBgpADConfigVplsId OBJECT-TYPE
SYNTAX VplsBgpRouteDistinguisher
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" VplsId is a unique identifier for all VSIs belonging to
the same VPLS. It is advertised as an extended community
"
::= { vplsBgpADConfigEntry 3 }
vplsBgpADConfigRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" For creating, modifying, and deleting this row.
None of the read-create objects in the
conceptual rows may be changed when this
object is in the active(1) state.
"
::= { vplsBgpADConfigEntry 4 }
-- vplsBgpRteTargetTable
vplsBgpRteTargetTable OBJECT-TYPE
SYNTAX SEQUENCE Of VplsBgpRteTargetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
" This table specifies the list of Route Targets
imported or exported by BGP during auto-discovery of VPLS.
"
::= { vplsObjects 5 }
vplsBgpRteTargetEntry OBJECT-TYPE
SYNTAX VplsBgpRteTargetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table specifies the value of the
L2 VPN Working Group Expires Dec 2010 [Page 20]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
Route Target being used by BGP. Depending on the value
of vplsBgpRteTargetType an RT might be exported or
imported or both. Every VPLS which
uses auto-discovery for finding peer nodes can import and
export multiple Route Targets. This representation allows
support for hierarchical VPLS.
"
INDEX { vplsConfigIndex, vplsBgpRteTargetIndex }
::= { vpsBgpRteTargetTable 1 }
VplsBgpRteTargetEntry ::=
SEQUENCE {
vplsBgpRteTargetIndex Unsigned32,
vplsBgpRteTargetRTType VplsBgpRouteTargetType,
vplsBgpRteTargetRT VplsBgpRouteTarget,
vplsBgpRteTargetRTRowStatus RowStatus
}
vplsBgpRteTargetIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This index along with vplsConfigIndex,identifies one entry
in the vplsBgpRteTargetTable. By keeping vplsConfigIndex
constant and using new value of vplsBgpRteTargetIndex user
can configure multiple Route Targets for the same Vpls.
"
::= { vplsBgpADConfigEntry 1 }
vplsBgpRteTargetRTType OBJECT-TYPE
SYNTAX VplsBgpRouteTargetType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" Used to define the type of a route target usage.
Route targets can be specified to be imported,
exported, or both. For a complete definition of a
route target, see [RFC4364]."
"
::= { vplsBgpADConfigEntry 2 }
vplsBgpRteTargetRT OBJECT-TYPE
SYNTAX VplsBgpRouteTarget
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" The route target associated with the VPLS service.
L2 VPN Working Group Expires Dec 2010 [Page 21]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
For more details on use of route targets
for a VPLS service, see [RFC4761]
"
::= { vplsBgpADConfigEntry 3 }
vplsBgpRteTargetRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable is used to create, modify, and/or
delete a row in this table. When a row in this
table is in active(1) state, no objects in that row
can be modified
"
::= { vplsBgpADConfigEntry 4 }
vplsStatusNotifEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If this object is set to true(1), then it enables
the emission of vplsStatusChanged
notification; otherwise this notification is not
emitted."
REFERENCE
"See also [RFC3413] for explanation that
notifications are under the ultimate control of the
MIB module in this document."
DEFVAL { false }
::= { vplsObjects 7 }
vplsNotificationMaxRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object indicates the maximum number of
notifications issued per second. If events occur
more rapidly, the implementation may simply fail to
emit these notifications during that period, or may
queue them until an appropriate time. A value of 0
means no throttling is applied and events may be
notified at the rate at which they occur."
DEFVAL { 0 }
::= { vplsObjects 8 }
L2 VPN Working Group Expires Dec 2010 [Page 22]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
-- VPLS Service Notifications
vplsStatusChanged NOTIFICATION-TYPE
OBJECTS {
vplsConfigVpnId,
vplsConfigAdminStatus,
vplsStatusOperStatus
}
STATUS current
DESCRIPTION
"The vplsStatusChanged notification is generated
when there is a change in the administrative or
operating status of a VPLS service."
::= { vplsNotifications 1 }
vplsFwdFullAlarmRaised NOTIFICATION-TYPE
OBJECTS {
vplsConfigVpnId,
vplsConfigFwdFullHighWatermark,
vplsConfigFwdFullLowWatermark
}
STATUS current
DESCRIPTION
"The vplsFwdFullAlarmRaised notification is
generated when the utilization of the Forwarding
database is above the value specified by
vplsConfigFwdFullHighWatermark."
::= { vplsNotifications 2 }
vplsFwdFullAlarmCleared NOTIFICATION-TYPE
OBJECTS {
vplsConfigVpnId,
vplsConfigFwdFullHighWatermark,
vplsConfigFwdFullLowWatermark
}
STATUS current
DESCRIPTION
"The vplsFwdFullAlarmCleared notification is
generated when the utilization of the Forwarding
database is below the value specified by
vplsConfigFwdFullLowWatermark."
::= { vplsNotifications 3 }
-- Compliance requirement for read-only implementations.
vplsCompliances
OBJECT IDENTIFIER ::= { vplsConformance 1 }
L2 VPN Working Group Expires Dec 2010 [Page 23]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
vplsModuleFullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance requirement for implementations that
provide full support for VPLS-GENERIC-DRAFT-01-MIB.
Such devices can then be monitored and configured using
this MIB module."
MODULE -- this module
MANDATORY-GROUPS {
vplsGroup,
vplsPwBindGroup,
vplsNotificationGroup
}
::= { vplsCompliances 1 }
vplsModuleReadOnlyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance requirement for implementations that only
provide read-only support for VPLS-GENERIC-DRAFT-01-MIB.
Such devices can then be monitored but cannot be
configured using this MIB modules."
MODULE -- this module
MANDATORY-GROUPS {
vplsGroup,
vplsPwBindGroup,
vplsNotificationGroup
}
OBJECT vplsConfigName
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT vplsConfigDescr
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT vplsConfigAdminStatus
MIN-ACCESS read-only
DESCRIPTION
L2 VPN Working Group Expires Dec 2010 [Page 24]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
"Write access is not required."
OBJECT vplsConfigMacLearning
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT vplsConfigDiscardUnknownDest
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT vplsConfigMacAging
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT vplsConfigFwdFullHighWatermark
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT vplsConfigFwdFullLowWatermark
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT vplsConfigRowStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT vplsConfigMtu
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT vplsConfigServiceType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT vplsPwBindConfigType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
L2 VPN Working Group Expires Dec 2010 [Page 25]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
OBJECT vplsPwBindType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT vplsPwBindRowStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { vplsCompliances 2 }
-- Units of conformance.
vplsGroups
OBJECT IDENTIFIER ::= { vplsConformance 2 }
vplsGroup OBJECT-GROUP
OBJECTS {
vplsConfigName,
vplsConfigDescr,
vplsConfigAdminStatus,
vplsConfigMacLearning,
vplsConfigDiscardUnknownDest,
vplsConfigMacAging,
vplsConfigVpnId,
vplsConfigFwdFullHighWatermark,
vplsConfigFwdFullLowWatermark,
vplsConfigRowStatus,
vplsConfigIndexNext,
vplsConfigMtu,
vplsConfigServiceType,
vplsConfigStorageType,
vplsStatusOperStatus,
vplsStatusPeerCount,
vplsStatusNotifEnable,
vplsNotificationMaxRate
}
STATUS current
DESCRIPTION
"The group of objects supporting
management of L2VPN VPLS services"
::= { vplsGroups 1 }
vplsPwBindGroup OBJECT-GROUP
L2 VPN Working Group Expires Dec 2010 [Page 26]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
OBJECTS {
vplsPwBindConfigType,
vplsPwBindType,
vplsPwBindRowStatus,
vplsPwBindStorageType
}
STATUS current
DESCRIPTION
"The group of objects supporting
management of
Pseudo Wire (PW) Binding to VPLS."
::= { vplsGroups 2 }
vplsNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
vplsStatusChanged,
vplsFwdFullAlarmRaised,
vplsFwdFullAlarmCleared
}
STATUS current
DESCRIPTION
"The group of notifications supporting
the Notifications generated for
VPLS Services"
::= { vplsGroups 3 }
END
6.2 VPLS-LDP-DRAFT-01-MIB Object definitions
This MIB module makes references to the following documents.
[RFC2578], [RFC2579], [RFC2580], [RFC3411],
[RFC2863], [RFC4001], [RFC4265] and [RFC3813].
VPLS-LDP-DRAFT-01-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE,
Unsigned32, transmission
FROM SNMPv2-SMI -- RFC2578
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF -- RFC2580
TruthValue
FROM SNMPv2-TC -- RFC2579
L2 VPN Working Group Expires Dec 2010 [Page 27]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
vplsConfigIndex, vplsPwBindIndex
FROM VPLS-GENERIC-DRAFT-01-MIB;
vplsLdpDraft01MIB MODULE-IDENTITY
LAST-UPDATED "200608301200Z" -- 20 August 2006 12:00:00 GMT
ORGANIZATION "Layer 2 Virtual Private Networks (L2VPN)
Working Group"
CONTACT-INFO
"
Thomas D. Nadeau
Email: tnadeau@cisco.com
The L2VPN Working Group (email distribution l2vpn@ietf.org,
http://www.ietf.org/html.charters/l2vpn-charter.html)
"
DESCRIPTION
"Copyright (C) The IETF Trust (2010). The initial
version of this MIB module was published in RFC XXXX.
-- RFC Editor: Please replace XXXX with RFC number & remove
-- this note.
For full legal notices see the RFC itself or see:
http://www.ietf.org/copyrights/ianamib.html
This MIB module contains managed object definitions for
LDP signalled Virtual Private LAN Services as in
[RFC4762]
This MIB module enables the use of any underlying PseudoWire
network. "
-- Revision history.
REVISION
"200608301200Z" -- 30 Aug 2006 12:00:00 GMT
DESCRIPTION "Initial version published as part of RFC YYYY."
-- RFC Editor: please replace YYYY with IANA assigned value, and
-- delete this note.
::= { transmission XXXX }
-- RFC Editor: please replace XXXX with IANA assigne value, and
-- delete this note.
-- Top-level components of this MIB.
L2 VPN Working Group Expires Dec 2010 [Page 28]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
-- Notifications
vplsLdpNotifications OBJECT IDENTIFIER
::= { vplsLdpDraft01MIB 0 }
-- Tables, Scalars
vplsLdpObjects OBJECT IDENTIFIER
::= { vplsLdpDraft01MIB 1 }
-- Conformance
vplsLdpConformance OBJECT IDENTIFIER
::= { vplsLdpDraft01MIB 2 }
vplsLdpConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF VplsLdpConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies information for configuring
and monitoring LDP specific parameters for
Virtual Private Lan Services(VPLS)."
::= { vplsLdpObjects 1 }
vplsLdpConfigEntry OBJECT-TYPE
SYNTAX VplsLdpConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in this table represents LDP specific information
for Virtual Private Lan Service(VPLS) in a packet network.
It is indexed by vplsConfigIndex, which uniquely
identifies a single VPLS.
A row is automatically created when a VPLS service is
configured using LDP signalling.
None of the read-create objects values can be
changed when vplsRowStatus is in the active(1)
state. Changes are allowed when the vplsRowStatus
is in notInService(2) or notReady(3) states only.
If the operator need to change one of the values
for an active row the vplsConfigRowStatus should be
first changed to notInService(2), the objects may
be changed now, and later to active(1) in order to
re-initiate the signaling process with the new
values in effect.
"
INDEX { vplsConfigIndex }
::= { vplsLdpConfigTable 1 }
L2 VPN Working Group Expires Dec 2010 [Page 29]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
VplsLdpConfigEntry ::=
SEQUENCE {
vplsLdpConfigMacAddrWithdraw TruthValue
}
vplsLdpConfigMacAddrWithdraw OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies if MAC address withdrawal
is enabled in this service. If this object is true then
Mac address withdrawl Learning is enabled. If false,
then Mac Learning is disabled."
DEFVAL { true }
::= { vplsLdpConfigEntry 1 }
-- VPLS LDP PW Binding Table
vplsLdpPwBindTable OBJECT-TYPE
SYNTAX SEQUENCE OF VplsLdpPwBindEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides LDP specific information for
an association between a VPLS service and the
corresponding Pseudo Wires. A service can have more
than one Pseudo Wire association. Pseudo Wires are
defined in the pwTable."
::= { vplsLdpObjects 2 }
vplsLdpPwBindEntry OBJECT-TYPE
SYNTAX VplsLdpPwBindEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each row represents an association between a
VPLS instance and one or more Pseudo Wires
defined in the pwTable. Each index is unique
in describing an entry in this table. However
both indexes are required to define the one
to many association of service to pseudowire.
An entry in this table in instantiated only when
LDP signalling is used to configure VPLS service.
Each entry in this table provides LDP specific
information for the VPlS represented by
L2 VPN Working Group Expires Dec 2010 [Page 30]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
vplsConfigIndex."
INDEX { vplsConfigIndex, vplsPwBindIndex }
::= { vplsLdpPwBindTable 1 }
VplsLdpPwBindEntry ::=
SEQUENCE {
vplsLdpPwBindMacAddressLimit Unsigned32
}
vplsLdpPwBindMacAddressLimit OBJECT-TYPE
SYNTAX Unsigned32 (0.. 4294967295)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object specifies the maximum number
of learned and static entries allowed in the
Forwarding database for this PW Binding. The value 0
means there is no limit for this PW Binding."
DEFVAL { 0 }
::= { vplsLdpPwBindEntry 1 }
-- VPLS Ldp Service Notifications
vplsLdpPwBindMacTableFull NOTIFICATION-TYPE
OBJECTS {
vplsConfigIndex,
vplsPwBindIndex
}
STATUS current
DESCRIPTION
"The vplsLdpPwBindMacTableFull notification is generated
when the number of learned MAC-Addresses increases to
the value specified in vplsLdpPwBindMacAddressLimit."
::= { vplsLdpNotifications 1 }
-- Compliance requirement for read-only implementations.
vplsLdpCompliances
OBJECT IDENTIFIER ::= { vplsLdpConformance 1 }
vplsLdpModuleFullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance requirement for implementations that
provide full support for VPLS-LDP-DRAFT-01-MIB.
Such devices can then be monitored and configured using
L2 VPN Working Group Expires Dec 2010 [Page 31]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
this MIB module."
MODULE -- this module
MANDATORY-GROUPS {
vplsLdpGroup,
vplsLdpNotificationGroup
}
::= { vplsLdpCompliances 1 }
vplsLdpModuleReadOnlyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance requirement for implementations that only
provide read-only support for VPLS-LDP-DRAFT-01-MIB.
Such devices can then be monitored but cannot be
configured using this MIB modules."
MODULE -- this module
MANDATORY-GROUPS {
vplsLdpGroup,
vplsLdpNotificationGroup
}
OBJECT vplsLdpConfigMacAddrWithdraw
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT vplsLdpPwBindMacAddressLimit
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { vplsLdpCompliances 2 }
-- Units of conformance.
vplsLdpGroups
OBJECT IDENTIFIER ::= { vplsLdpConformance 2 }
vplsLdpGroup OBJECT-GROUP
OBJECTS {
vplsLdpConfigMacAddrWithdraw,
vplsLdpPwBindMacAddressLimit
L2 VPN Working Group Expires Dec 2010 [Page 32]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
}
STATUS current
DESCRIPTION
"The group of objects supporting
management of L2VPN VPLS services using LDP."
::= { vplsLdpGroups 1 }
vplsLdpNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
vplsLdpPwBindMacTableFull
}
STATUS current
DESCRIPTION
"The group of notifications supporting
the Notifications generated for
VPLS Ldp Service"
::= { vplsLdpGroups 2 }
END
6.3 VPLS-BGP-DRAFT-01-MIB Object definitions
VPLS-BGP-DRAFT-01-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE,
Unsigned32, transmission
FROM SNMPv2-SMI -- RFC2578
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF -- RFC2580
RowStatus, StorageType, TEXTUAL-CONVENTION
FROM SNMPv2-TC -- RFC2579
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB -- RFC3411
vplsConfigIndex, vplsPwBindIndex
FROM VPLS-GENERIC-DRAFT-01-MIB
;
vplsBgpDraft01MIB MODULE-IDENTITY
LAST-UPDATED "200612061200Z" -- 06 Dec 2006 12:00:00 GMT
ORGANIZATION "Layer 2 Virtual Private Networks (L2VPN)
Working Group"
CONTACT-INFO
L2 VPN Working Group Expires Dec 2010 [Page 33]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
"
V. J. Shah
Email: vshah@juniper.net
The L2VPN Working Group (email distribution l2vpn@ietf.org,
http://www.ietf.org/html.charters/l2vpn-charter.html)
"
DESCRIPTION
"Copyright (C) The IETF Trust (2010). The initial
version of this MIB module was published in RFC XXXX.
-- RFC Editor: Please replace XXXX with RFC number & remove
-- this note.
For full legal notices see the RFC itself or see:
http://www.ietf.org/copyrights/ianamib.html
This MIB module contains managed object definitions for
BGP signalled Virtual Private LAN Services as in
[RFC4761]
This MIB module enables the use of any underlying PseudoWire
network. "
-- Revision history.
REVISION
"200612061200Z" -- 06 Dec 2006 12:00:00 GMT
DESCRIPTION "Initial version published as part of RFC YYYY."
-- RFC Editor: please replace YYYY with IANA assigned value, and
-- delete this note.
::= { transmission XXXX }
-- RFC Editor: please replace XXXX with IANA assigne value, and
-- delete this note.
-- VPLS BGP specific Textual Conventions.
VplsBgpRouteDistinguisher ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Syntax for a route distinguisher. For a complete
definition of a route distinguisher, see [RFC4364].
For more details on use of a route distinguisher
for a VPLS service, see [RFC4761]"
REFERENCE
"[RFC4364]"
SYNTAX OCTET STRING(SIZE (0..256))
VplsBgpRouteTarget ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
L2 VPN Working Group Expires Dec 2010 [Page 34]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
"Syntax for a route target. For a complete
definition of a route target, see [RFC4364]."
REFERENCE
"[RFC4364]"
SYNTAX OCTET STRING(SIZE (0..256))
-- Top-level components of this MIB.
-- Tables, Scalars
vplsBgpObjects OBJECT IDENTIFIER
::= { vplsBgpDraft01MIB 1 }
-- Conformance
vplsBgpConformance OBJECT IDENTIFIER
::= { vplsBgpDraft01MIB 2 }
-- Vpls Bgp Config Table
vplsBgpConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF VplsBgpConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies information for configuring
and monitoring BGP specific parameters for
Virtual Private Lan Services(VPLS)."
::= { vplsBgpObjects 1 }
vplsBgpConfigEntry OBJECT-TYPE
SYNTAX VplsBgpConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in this table represents BGP specific information
for Virtual Private Lan Service(VPLS) in a packet network.
It is indexed by vplsConfigIndex, which uniquely
identifies a single instance of a VPLS service.
A row is automatically created when a VPLS service is
configured using BGP signalling.
None of the read-create objects values can be
changed when vplsRowStatus is in the active(1)
state. Changes are allowed when the vplsRowStatus
is in notInService(2) or notReady(3) states only.
If the operator need to change one of the values
for an active row the vplsConfigRowStatus should be
first changed to notInService(2), the objects may
be changed now, and later to active(1) in order to
L2 VPN Working Group Expires Dec 2010 [Page 35]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
re-initiate the signaling process with the new
values in effect.
"
INDEX { vplsConfigIndex }
::= { vplsBgpConfigTable 1 }
VplsBgpConfigEntry ::=
SEQUENCE {
vplsBgpConfigVERangeSize Unsigned32
}
vplsBgpConfigVERangeSize OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the size of the range of VE ids in this
VPLS service. This number controls the size of the
label block advertised for this VE by the PE.
A value of 0 indicates that the range is not
configured and the PE derives the range value
from received advertisements from other PEs."
DEFVAL { 0 }
::= { vplsBgpConfigEntry 1 }
-- Vpls Edge Device (VE) Identifier Table
vplsBgpVETable OBJECT-TYPE
SYNTAX SEQUENCE OF VplsBgpVEEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table associates VPLS Edge devices to a VPLS service"
::= { vplsBgpObjects 2 }
vplsBgpVEEntry OBJECT-TYPE
SYNTAX VplsBgpVEEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created for each VE Id
configured on a PE for a particular VPLS service
instance."
INDEX { vplsConfigIndex, vplsBgpVEId }
::= { vplsBgpVETable 1 }
VplsBgpVEEntry ::= SEQUENCE {
vplsBgpVEId Unsigned32,
L2 VPN Working Group Expires Dec 2010 [Page 36]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
vplsBgpVEName SnmpAdminString,
vplsBgpVEPreference Unsigned32,
vplsBgpVERowStatus RowStatus,
vplsBgpVEStorageType StorageType
}
vplsBgpVEId OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A secondary index identifying a VE within an
instance of a VPLS service."
::= { vplsBgpVEEntry 1 }
vplsBgpVEName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Descriptive name for the site or u-PE assciated with
this VE Id."
DEFVAL { "" }
::= { vplsBgpVEEntry 2 }
vplsBgpVEPreference OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the preference of the VE Id on this PE
if the site is multi-homed and VE Id is re-used."
DEFVAL { 0 }
::= { vplsBgpVEEntry 3 }
vplsBgpVERowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable is used to create, modify, and/or
delete a row in this table. When a row in this
table is in active(1) state, no objects in that row
can be modified except vplsBgpSiteRowStatus."
::= { vplsBgpVEEntry 5 }
vplsBgpVEStorageType OBJECT-TYPE
SYNTAX StorageType
L2 VPN Working Group Expires Dec 2010 [Page 37]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable indicates the storage type for this row."
DEFVAL { volatile }
::= { vplsBgpVEEntry 6 }
-- VPLS BGP PW Binding Table
vplsBgpPwBindTable OBJECT-TYPE
SYNTAX SEQUENCE OF VplsBgpPwBindEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides BGP specific information for
an association between a VPLS service and the
corresponding Pseudo Wires. A service can have more
than one Pseudo Wire association. Pseudo Wires are
defined in the pwTable."
::= { vplsBgpObjects 3 }
vplsBgpPwBindEntry OBJECT-TYPE
SYNTAX VplsBgpPwBindEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each row represents an association between a
VPLS instance and one or more Pseudo Wires
defined in the pwTable. Each index is unique
in describing an entry in this table. However
both indexes are required to define the one
to many association of service to pseudowire.
An entry in this table in instantiated only when
BGP signalling is used to configure VPLS service.
Each entry in this table provides BGP specific
information for the VPlS represented by
vplsConfigIndex."
INDEX { vplsConfigIndex, vplsPwBindIndex }
::= { vplsBgpPwBindTable 1 }
VplsBgpPwBindEntry ::=
SEQUENCE {
vplsBgpPwBindLocalVEId Unsigned32,
vplsBgpPwBindRemoteVEId Unsigned32
}
L2 VPN Working Group Expires Dec 2010 [Page 38]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
vplsBgpPwBindLocalVEId OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Identifies the local VE that this Pseudo Wire
is associated with."
::= { vplsBgpPwBindEntry 1 }
vplsBgpPwBindRemoteVEId OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Identifies the remote VE that this Pseudo Wire
is associated with."
::= { vplsBgpPwBindEntry 2 }
-- Compliance requirement for read-only implementations.
vplsBgpCompliances
OBJECT IDENTIFIER ::= { vplsBgpConformance 1 }
vplsBgpModuleFullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance requirement for implementations that
provide full support for VPLS-BGP-DRAFT-01-MIB.
Such devices can then be monitored and configured using
this MIB module."
MODULE -- this module
MANDATORY-GROUPS {
vplsBgpConfigGroup,
vplsBgpVEGroup,
vplsBgpPwBindGroup
}
::= { vplsBgpCompliances 1 }
vplsBgpModuleReadOnlyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance requirement for implementations that only
provide read-only support for VPLS-BGP-DRAFT-01-MIB.
Such devices can then be monitored but cannot be
configured using this MIB modules."
L2 VPN Working Group Expires Dec 2010 [Page 39]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
MODULE -- this module
MANDATORY-GROUPS {
vplsBgpConfigGroup,
vplsBgpVEGroup,
vplsBgpPwBindGroup
}
OBJECT vplsBgpConfigRouteDistinguisher
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT vplsBgpConfigRouteTarget
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT vplsBgpConfigVERangeSize
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT vplsBgpVEName
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT vplsBgpVEPreference
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT vplsBgpVERowStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { vplsBgpCompliances 2 }
-- Units of conformance.
vplsBgpGroups
OBJECT IDENTIFIER ::= { vplsBgpConformance 2 }
vplsBgpConfigGroup OBJECT-GROUP
OBJECTS {
L2 VPN Working Group Expires Dec 2010 [Page 40]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
vplsBgpConfigVERangeSize
}
STATUS current
DESCRIPTION
"The group of objects supporting configuration
of L2VPN VPLS services using BGP"
::= { vplsBgpGroups 1 }
vplsBgpVEGroup OBJECT-GROUP
OBJECTS {
vplsBgpVEName,
vplsBgpVEPreference,
vplsBgpVERowStatus,
vplsBgpVEStorageType
}
STATUS current
DESCRIPTION
"The group of objects supporting management of VPLS
Edge devices for L2VPN VPLS services using BGP"
::= { vplsBgpGroups 2 }
vplsBgpPwBindGroup OBJECT-GROUP
OBJECTS {
vplsBgpPwBindLocalVEId,
vplsBgpPwBindRemoteVEId
}
STATUS current
DESCRIPTION
"The group of objects supporting management of
Pseudo Wires for L2VPN VPLS services using BGP"
::= { vplsBgpGroups 3 }
END
7. Security Considerations
It is clear that the MIB modules described in this document in
association with the PW-STD-MIB [RFC5601] are potentially
useful for monitoring of GMPLS LSRs. These MIB modules can also be
used for configuration of certain objects, and anything that can be
configured can be incorrectly configured, with potentially disastrous
results.
There are a number of management objects defined in these MIB modules
with a MAX-ACCESS clause of read-write and/or read-create. Such
objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
L2 VPN Working Group Expires Dec 2010 [Page 41]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
network operations. These are the tables and objects and their
sensitivity/vulnerability:
8. IANA Considerations
-- (Note to RFC-Editor:)
-- We request that you assign contiguous RFC numbers to the
-- IANA is requested to root MIB objects in the MIB module
-- contained in this document under the transmission subtree.
--
9. References
9.1 Normative References
[RFC2119] S. Bradner, "Key Words for use in RFCs to Indicate
Requirement Levels", RFC 2119, BCP 14, March 1997.
[RFC2863] McCloghrie, K. and F. Kastenholtz, "The Interfaces Group
MIB", RFC 2863, June 2000.
[RFC3413] Levi, D., Meyer, P., and B. Stewart, "Simple Network
Management Protocol (SNMP) Applications", STD 62, RFC
3413, December 2002.
[RFC3415] Wijnen, B., Presuhn, R. and K. McCloghrie, "View-
based Access Control Model (VACM) for the Simple
Network Management Protocol (SNMP)", STD 62, RFC
3415, December 2002.
[RFC3813] Srinivasan, C., Viswanathan, A. and Nadeau, T.,
"Multiprotocol Label Switching (MPLS) Label Switching
Router (LSR) Management Information Base",
RFC 3813, June 2004
[RFC3985] Bryant, S. and P. Pate, "Pseudo Wire Emulation Edge-to-
Edge (PWE3) Architecture", RFC 3985, March 2005.
[RFC4001] Daniele, M., Haberman, B., Routhier, S., and J.
Schoenwaelder, "Textual Conventions for Internet Network
Addresses", RFC 4001, Feb 2005.
[RFC4188] Norseth, K., and Bell, E., "Definitions of Managed
Objects for Bridges", RFC 4188, Sept 2006.
[RFC4265] Schliesser, B. and T. Nadeau, "Definition of Textual
Conventions for Virtual Private Network (VPN) Management",
RFC 4265, November 2005.
L2 VPN Working Group Expires Dec 2010 [Page 42]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
[RFC4364] Rosen, E. and Y. Rekhter, "BGP/MPLS IP Virtual Private
Networks (VPNs)", RFC 4364, February 2006.
[RFC4761] Kompella, K. and Y. Rekhter, "Virtual Private LAN Service
(VPLS) Using BGP for Auto-Discovery and Signaling",RFC
4761, January 2007.
[RFC4762] Lasserre, M. and Kompella, V. (Editors), "Virtual Private
LAN Service (VPLS) Using Label Distribution Protocol (LDP)
Signaling", RFC 4762, January 2007.
[RFC5601] T. Nadeau, Ed., D. Zelig, Ed., "Pseudowire (PW)
Management Information Base (MIB)", RFC 5601, July 2009.
9.2 Informative References
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case,
J., Rose, M., and S. Waldbusser, "Structure of
Management Information Version 2 (SMIv2)", STD 58, RFC
2578, April 1999.
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case,
J., Rose, M., and S. Waldbusser, "Textual Conventions
for SMIv2", STD 58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case,
J., Rose, M., and S. Waldbusser, "Conformance
Statements for SMIv2", STD 58, RFC 2580, April 1999.
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction and Applicability Statements for
Internet-Standard Management Framework", RFC 3410,
December 2002.
[RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An
Architecture for Describing Simple Network Management
Protocol (SNMP) Management Frameworks", STD 62, RFC 3411,
December 2002.
[SNMP-CONTEXT-MAP-MIB] SNMP Context Mapping MIB, AS, Kiran Koushik,
Nadeau, T, draft-kkoushik-snmp-context-map-mib.
L2 VPN Working Group Expires Dec 2010 [Page 43]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
10 Acknowledgement
We wish to thank Marcelo Mourier and Reva Bailey for their
valuable feedback. Some portion of the work has been referenced
from their original Timetra Enterprise MIB work.
11 Authors' Addresses
Thomas D. Nadeau
Cisco Systems, Inc.
1414 Massachusetts Ave.
Boxborough, MA 01719
Email: tnadeau@cisco.com
A S Kiran Koushik
Cisco Systems Inc.
12515 Research Blvd, Bldg 4,
Austin, TX 78759
Email: kkoushik@cisco.com
Rohit Mediratta
Alcatel-Lucent,
701 E Middlefield Rd.
Mountain View, CA 94040
Email: rohit.mediratta@alcatel-lucent.com
Praveen Muley
Alcatel-Lucent
Email: praveen.muley@alcatel-lucent.com
Reva Bailey
Alcatel-Lucent
Email: reva.bailey@alcatel-lucent.com
VJ Shah
Juniper Networks
Email: vshah@juniper.net
L2 VPN Working Group Expires Dec 2010 [Page 44]
draft-ietf-l2vpn-vpls-mib-04 L2-VPN-MIB Apr 07, 2010
Li Wentao
ZTE Inc.
CHINA
Email: li.wentao@zte.com.cn
Kong Yong
ZTE Inc.
CHINA
Email: kong.yong@zte.com.cn
Luo Jian
ZTE Inc.
CHINA
Email: luo.jian@zte.com.cn
Feng Jun
ZTE Inc.
CHINA
Email: Feng.jun99@zte.com.cn
Takeshi Usui
KDDI Corpration
Japan
Email:ta-usui@kddi.com
12 Full Copyright Statement
Copyright (c) 2010 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
This document may contain material from IETF Documents or IETF
Contributions published or made publicly available before November
10, 2008. The person(s) controlling the copyright in some of this
material may not have granted the IETF Trust the right to allow
modifications of such material outside the IETF Standards Process.
Without obtaining an adequate license from the person(s)
controlling the copyright in such materials, this document may not
be modified outside the IETF Standards Process, and derivative
works of it may not be created outside the IETF Standards Process,
except to format it for publication as an RFC or to translate it
into languages other than English.
L2 VPN Working Group Expires Dec 2010 [Page 45]
| PAFTECH AB 2003-2026 | 2026-04-21 21:08:42 |