One document matched: draft-ietf-ippm-ipdv-03.txt
Differences from draft-ietf-ippm-ipdv-02.txt
Network Working Group C. Demichelis
INTERNET-DRAFT CSELT
Expiration Date: December 1999 P. Chimento
CTIT
June 1999
Instantaneous Packet Delay Variation Metric for IPPM
<draft-ietf-ippm-ipdv-03.txt>
1. Status of this Memo
This document is an Internet-Draft and is in full conformance with |
all provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at |
http://www.ietf.org/ietf/1id-abstracts.txt |
The list of Internet-Draft shadow directories can be accessed at |
http://www.ietf.org/shadow.html
This memo provides information for the Internet community. This memo
does not specify an Internet standard of any kind. Distribution of
this memo is unlimited.
2. Abstract
This memo refers to a metric for variation in delay of packets across
Internet paths. The metric is based on statistics of the difference
in One-Way-Delay of consecutive packets. This particular definition
of variation is called "Instantaneous Packet Delay Variation (ipdv)".
The metric is valid for measurements between two hosts both in the
case that they have synchronized clocks and in the case that they are
not synchronized. In the second case it allows an evaluation of the
Demichelis and Chimento [Page 1]
INTERNET-DRAFT Packet Delay Variation June 1999
reciprocal skew. Measurements performed on both directions (Two-way
measurements) allow a better estimation of clock differences. The
precision that can be obtained is evaluated.
3. Introduction
This memo takes as a reference the Draft-ietf "One-Way-Delay metric |
for IPPM" [1]. Part of the text in this memo is directly taken from
that Draft.
This memo defines a metric for variation in delay of packets that
flow from one host to another one through an IP path. Since the
metric is related to a variation, different definitions are possible
according to what the variation is measured against.
"Jitter" commonly has two meanings: The first meaning is the |
variation of a signal with respect to some clock signal, where the |
arrival time of the signal is expected to coincide with the arrival |
of the clock signal. The second meaning has to do with the variation |
of a metric (e.g. delay) with respect to some reference metric (e.g. |
average delay or minimum delay). The form of "jitter" that we talk |
about here has to do almost exclusively with the second meaning, |
rather than the first. See the section on the relationship with other |
standards.
3.1. Definition
A definition of the Instantaneous Packet Delay Variation (ipdv) can
be given for a pair of packets or for a packet inside a stream of
packets.
For a pair of packets:
+ The ipdv of a pair of IP packets, that are transmitted from the
measurement point MP1 to the measurement point MP2, is the
difference between the One-Way-Delay measured for the second
packet and the One-Way-Delay measured for the first packet of the
pair.
For a stream of packets:
+ The Instantaneous Packet Delay Variation of an IP packet, inside a
stream of packets, going from the measurement point MP1 to the
measurement point MP2, is the difference of the One-Way-Delay of
that packet and the One-Way-Delay of the preceding packet in the
Demichelis and Chimento [Page 2]
INTERNET-DRAFT Packet Delay Variation June 1999
stream.
3.2. Motivation
A number of services that can be supported by IP are sensitive to the
regular delivery of packets and can be disturbed by instantaneous
variations in delay, while they are not disturbed by slow variations,
that can last a relatively long time. A specific metric for quick
variations is therefore desirable. Metrics that can be derived from
the analysis of statistics of ipdv can also be used, for example, for |
buffer dimensioning. The scope of this metric is to provide a way
for measurement of the quality delivered by a path.
In addition, this type of metric is particularly robust with respect
differences and variations of the clocks of the two hosts. This
allows the use of the metric even if the two hosts that support the
measurement points are not synchronized. In the latter case
indications of reciprocal skew of the clocks can be derived from the
measurement and corrections are possible. The related precision is
often comparable with the one that can be achieved with synchronized
clocks, being of the same order of magnitude of synchronization
errors. This will be discussed below.
3.3. General Issues Regarding Time
Everything contained in the Section 2.2. of [2] applies also in this |
case.
In addition, we assume here that the reciprocal skew of the two
clocks can be decomposed into two parts:
+ A fixed one, called in this context "skew", given, for example, by
tolerances in physical dimensions of crystals.
+ A variable one, called in this context "drift", given, for
example, by changes in temperature or other conditions of
operation. Both of these components are part of the term "skew" as
defined in the referenced Draft and in the Framework document.
NOTE: The drift of a clock, as it is above defined over a long period
must have an average value that tends to zero while the period
becomes large since the frequency of the clock has a finite (and
small) range. In order to underline the order of magnitude of this
effect,it is considered that the maximum range of drift for
commercial crystals is about 50 part per million (ppm). Since it is
Demichelis and Chimento [Page 3]
INTERNET-DRAFT Packet Delay Variation June 1999
mainly connected with variations in operating temperature (from 0 to
70 degrees Celsius), it is expected that a host will have a nearly
constant temperature during its operation period, and variations in
temperature, even if quick, could be less than one Celsius per
second, and range in the order of few degrees. The total range of the
drift is usually related to variations from 0 to 70 Celsius. These
are important points for evaluation of precision of ipdv
measurements, as will be seen below.
4. Structure of this memo
The metric will be defined as applicable to a stream of packets that
flow from a source host to a destination host (one-way ipdv). The
initial assumption is that source and destination hosts have
synchronized clocks. The definition of a singleton of one-way ipdv
metric is first considered, and then a definition of samples for ipdv
will be given.
Then the case of application to non-synchronized hosts will be
discussed, and the precision will be compared with the one of
synchronized clocks.
A bidirectional ipdv metric will be defined, as well as the
methodology for error corrections. This will not be a two-way metric,
but a "paired" one-way in opposite directions. Some statistics
describing the IP path's behavior will be proposed.
5. A singleton definition of a One-way ipdv metric |
This definition makes use of the corresponding definition of type-P-
One-Way-Delay metric [2]. This section makes use of those parts of
the One-Way-Delay Draft that directly apply to the One-Way-ipdv
metric, or makes direct references to that Draft.
5.1. Metric name
Type-P-One-way-ipdv
Demichelis and Chimento [Page 4]
INTERNET-DRAFT Packet Delay Variation June 1999
5.2. Metric parameters
+ Src, the IP address of a host
+ Dst, the IP address of a host
+ T1, a time
+ T2, a time. It is explicitly noted that also the difference T2-T1
is a parameter of the measurement though this is already implicit,
since the times T1 and T2 exactly define the time conditions in
which the measurement takes place.
Note that the packet length is an implicit parameter of both the |
Type-P-One-way-delay metric and the Type-P-One-way-ipdv metric, since |
this contributes to the overall one-way delay. We assume that the |
packets sent for ipdv measurements are all of the same length.
5.3. Metric unit
The value of a Type-P-One-way-ipdv is either a real number of seconds
(positive, zero or negative) or an undefined number of seconds.
5.4. Definition
Type-P-One-way-ipdv is defined for two (consecutive) packets from Src
to Dst, as the difference between the value of the type-P-One-way-
delay from Src to Dst at T2 [via path] and the value of the type-P-
One-Way-Delay from Src to Dst at T1 [via path]. T1 is the wire-time
at which Scr sent the first bit of the first packet, and T2 is the
wire-time at which Src sent the first bit of the second packet. This
metric is therefore ideally derived from the One-Way-Delay metric.
NOTE: The requirement of "consecutive" packets is not essential. The
measured value is anyway the difference in One-Way-Delay at the times
T1 and T2, which is meaningful by itself, as long as the times T1 and |
T2 denote the wire times of the packets sent from Src to Dst.
Therefore, for a real number ddT "The type-P-one-way-ipdv from Src to
Dst at T1, T2 [via path] is ddT" means that Src sent two consecutive
packets, the first at wire-time T1 (first bit), and the second at
wire-time T2 (first bit) and the packets were received by Dst at
wire-time dT1+T1 (last bit of the first packet), and at wire-time
Demichelis and Chimento [Page 5]
INTERNET-DRAFT Packet Delay Variation June 1999
dT2+T2 (last bit of the second packet), and that dT2-dT1=ddT.
"The type-P-one-way-ipdv from Src to Dst at T1,T2 [via path] is
undefined" means that Src sent the first bit of a packet at T1 and
the first bit of a second packet at T2 and that Dst did not receive
one or both packets.
5.5. Discussion
Type-P-One-way-ipdv is a metric that makes use of the same
measurement methods provided for delay metrics.
The following practical issues have to be considered:
+ Being a differential measurement, this metric is less sensitive to
clock synchronization problems. This issue will be more carefully
examined in section 7 of this memo. It is pointed out that, if the
reciprocal clock conditions change in time, the accuracy of the
measurement will depend on the time interval T2-T1 and the
magnitude of possible errors will be discussed below.
+ A given methodology will have to include a way to determine
whether a delay value is infinite or whether it is merely very
large (and the packet is yet to arrive at Dst). As noted by
Mahdavi and Paxson, simple upper bounds (such as the 255 seconds
theoretical upper bound on the lifetimes of IP packets [Postel:
RFC 791]) could be used, but good engineering, including an
understanding of packet lifetimes, will be needed in practice.
{Comment: Note that, for many applications of these metrics, the
harm in treating a large delay as infinite might be zero or very
small. A TCP data packet, for example, that arrives only after
several multiples of the RTT may as well have been lost.}
+ As with other 'type-P' metrics, the value of the metric may depend
on such properties of the packet as protocol,(UDP or TCP) port
number, size, and arrangement for special treatment (as with IP
precedence or with RSVP).
+ If the packet is duplicated along the path (or paths!) so that
multiple non-corrupt copies arrive at the destination, then the
packet is counted as received, and the first copy to arrive
determines the packet's One-Way-Delay.
+ If the packet is fragmented and if, for whatever reason,
reassembly does not occur, then the packet will be deemed lost.
Demichelis and Chimento [Page 6]
INTERNET-DRAFT Packet Delay Variation June 1999
5.6. Methodologies
As with other Type-P-* metrics, the detailed methodology will depend
on the Type-P (e.g., protocol number, UDP/TCP port number, size,
precedence). Generally, for a given Type-P, the methodology would
proceed as follows:
+ The need of synchronized clocks for Src and Dst will be discussed
later. Here a methodology is supposed that is based on
synchronized clocks.
+ At the Src host, select Src and Dst IP addresses, and form two
test packets of Type-P with these addresses. Any 'padding' portion
of the packet needed only to make the test packet a given size
should be filled with randomized bits to avoid a situation in
which the measured delay is lower than it would otherwise be due
to compression techniques along the path.
+ At the Dst host, arrange to receive the packets.
+ At the Src host, place a timestamp in the first Type-P packet,
and send it towards Dst [via path].
+ If the packet arrives within a reasonable period of time, take a
timestamp as soon as possible upon the receipt of the packet. By
subtracting the two timestamps, an estimate of One-Way-Delay can
be computed.
+ Record this first delay value.
+ At the Src host, place a timestamp in the second Type-P packet,
and send it towards Dst [via path].
+ If the packet arrives within a reasonable period of time, take a
timestamp as soon as possible upon the receipt of the packet. By
subtracting the two timestamps, an estimate of One-Way-Delay can
be computed.
+ By subtracting the second value of One-Way-Delay from the first
value the ipdv value of the pair of packets is obtained.
+ If one or both packets fail to arrive within a reasonable period
of time, the ipdv is taken to be undefined.
Demichelis and Chimento [Page 7]
INTERNET-DRAFT Packet Delay Variation June 1999
5.7. Errors and Uncertainties
In the singleton metric of ipdv, factors that affect the measurement
are the same that can affect the One-Way-Delay measurement, even if,
in this case, the influence is different.
The Framework document [1] provides general guidance on this point,
but we note here the following specifics related to delay metrics:
+ Errors/uncertainties due to uncertainties in the clocks of the Src
and Dst hosts.
+ Errors/uncertainties due to the difference between 'wire time' and
'host time'.
Each of these errors is discussed in more detail in the next
paragraphs.
5.7.1. Errors/Uncertainties related to Clocks
If, as a first approximation, the error that affects the first
measurement of One-Way-Delay were the same of the one affecting the
second measurement, they will cancel each other when calculating
ipdv. The residual error related to clocks is the difference of the
errors that are supposed to change from the time T1, at which the
first measurement is performed, to the time T2 at which the second
measure ment is performed. Synchronization, skew, accuracy and
resolution are here considered with the following notes:
+ Errors in synchronization between source and destination clocks
contribute to errors in both of the delay measurements required
for calculating ipdv.
+ If the synchronization error affecting the One-Way-Delay
measurement is Tsync, and it is a linear function of time, through
the skew value "sk", at time T1 the error will be Tsync1 and at
time T2 the error will be Tsync2. The ipdv measurement will be
affected by the error: Tsync2-Tsync1 = sk x (T2 - T1) depending on
skew and T2-T1. To minimize this error it is possible to reduce
the time interval T2-T1, but this could limit the generality of
the metric. Methods for evaluating the synchronization error will
be discussed below, since they come from a statistic over a
significant sample. If the measurement conditions do not allow
neglecting the drift, assumed linear in the interval T2-T1, and
having a value of "dr" expressed in ppm / sec., the ipdv error
will become: Tsync2-Tsync1 = sk x (T2 - T1) + [dr x (T2-T1) x
(T2-T1)] / 2 Drift varies the skew value in the time. The limits
in which the skew can vary are anyway limited and small, so that a
Demichelis and Chimento [Page 8]
INTERNET-DRAFT Packet Delay Variation June 1999
given drift cannot act indefinitely. Section 7 and Appendix A
provide more information on this point.
+ As far as accuracy and resolution are concerned, what is noted in
the Draft on One-Way-Delay [2] in section 3.7.1, applies also in
this case, with the further consideration, about resolution, that
in this case the uncertainty introduced is two times the one of a
single delay measurement. Errors introduced by these effects are
often larger than the ones introduced by the drift.
5.7.2. Errors/uncertainties related to Wire-time vs Host-time
The content of sec. 3.7.2 of [2] applies also in this case, with the
following further consideration: The difference between Host-time and
Wire-time can be in general decomposed into two components, of which
one is constant and the other is variable. Only the variable
components will produce measurement errors, while the constant one
will be canceled while calculating ipdv.
6. Definitions for Samples of One-way ipdv
Starting from the definition of the singleton metric of one-way ipdv, |
we define a sample of such singletons. In the following, the two |
packets needed for a singleton measurement will be called a "pair". |
A stream of test packets is generated where the second packet of a |
pair is, at the same time, the first packet of the next pair. |
+ Given particular binding of the parameters Src, Dst and Type-P, a |
sample of values of parameter T1 is defined. To define the values |
of T1, select a beginning time T0, a final time Tf, and an average |
rate lambda, then define a pseudo-random Poisson arrival process |
of rate lambda, whose values fall between T0 and Tf. The time |
interval between successive values of T1 will then average |
1/lambda. From the second value on, T1 value of the pair n |
coincides with T2 of the pair n-1, and the first packet of pair n |
coincides with the second packet of the pair n-1. |
6.1. Metric name
Type-P-One-way-ipdv-stream
Demichelis and Chimento [Page 9]
INTERNET-DRAFT Packet Delay Variation June 1999
6.2. Parameters
+ Src, the IP address of a host
+ Dst, the IP address of a host
+ T0, a time
+ Tf, a time
+ lambda, a rate in reciprocal seconds
6.3. Metric Units:
A sequence of triads whose elements are:
+ T, a time
+ Ti, a time interval.
+ dT a real number or an undefined number of seconds
6.4. Definition
A pseudo-random Poisson process is defined such that it begins at or
before T0, with average arrival rate lambda, and ends at or after Tf.
Those time values T(i) greater than or equal to T0 and less than or
equal to Tf are then selected. Starting from time T0, at each pair of
times T(i), T(i+1) of this process a value of Type-P-One-way-ipdv is
obtained. The value of the sample is the sequence made up of the
resulting <time, time interval, ipdv> triple, where the time interval
is given by T(i+1)-T(i). Each time T(i), excluding the first and the
last, is therefore at the same time the the second time of pair i and
the first time of pair i+1. The result is shown in figure 3
|T(i-2) |T(i-1) |T(i) |T(i+1)
_____|__________|___________________|__________|________
pair i-1 pair i pair i+1
Figure 3
Demichelis and Chimento [Page 10]
INTERNET-DRAFT Packet Delay Variation June 1999
6.5. Discussion
Note first that, since a pseudo-random number sequence is employed,
the sequence of times, and hence the value of the sample, is not
fully specified. Pseudo-random number generators of good quality will
be needed to achieve the desired qualities.
The sample is defined in terms of a Poisson process both to avoid the
effects of self-synchronization and also capture a sample that is
statistically as unbiased as possible. {Comment: there is, of course,
no claim that real Internet traffic arrives according to a Poisson
arrival process.}
6.6. Methodology
Since packets can be lost or duplicated or can arrive in a different
order than the order sent, in order to recognize the pairs of test
packets, they should be marked with a sequence number. For duplicated
packets only the first received copy should be considered. If a
packet is lost, two values of ipdv will be undefined, since each
packet is common to two pairs.
Steps for measurement can be the following:
+ Starting from a given time T, Src generates a test packet as for a
singleton metrics, inserts in the packet a sequence number and the
transmission time stamp Tx, then sorts the time Ti at which the
next packet has to be sent.
+ At time Ti, Src repeats the previous step, unless T(i) > Tf.
+ On reception of the first packet, or the first packet after a
sequence number error, Dst records sequence number and
transmission timestamp that are contained in the packet and the
reception time Rx as "old values".
+ On reception of the other packets Dst verifies the seuqence number
and if it is correct, by using the "old values" and the newly
received ones, a value of ipdv is computed. Then Dst records the
new sequence number, transmit and receive timestamps as "old
values".
Demichelis and Chimento [Page 11]
INTERNET-DRAFT Packet Delay Variation June 1999
6.7. Errors and uncertainties
The same considerations apply that have been made about the singleton
metric. An additional error can be introduced by the pseudo-random
Poisson process as focused in [2]. Further considerations will be
made in section 7, and in Appendix A.
6.8. Distribution of One-way-ipdv values |
The one-way-ipdv values are limited by virtue of the fact that there |
are upper and lower bounds on the one-way-delay values. Specifically, |
one-way-delay is upper bounded by the value chosen as the maximum |
beyond which a packet is counted as lost. It is lower bounded by |
propagation, transmission and nodal transit delays assuming that |
there are no queues or variable nodal delays in the path. Denote the |
upper bound of one-way-delay by U and the lower bound by L and we see |
that one-way-ipdv can only take on values in the (open) interval (L- |
U, U-L). |
In any finite interval, the one-way-delay can vary monotonically |
(non-increasing or non-decreasing) or of course it can vary in both |
directions in the interval, within the limits of the half-open |
interval [L,U). Accordingly, within that interval, the one-way-ipdv |
values can be positive, negative, or a mixture (including 0). |
Since the range of values is limited, the one-way-ipdv cannot |
increase or decrease indefinitely. Suppose, for example, that the |
ipdv has a positive 'run' (i.e. a long sequence of positive values). |
At some point in this 'run', the positive values must approach 0 (or |
become negative) if the one-way-delay remains finite. Otherwise, the |
one-way-delay bounds would be violated. If such a run were to |
continue infinitely long, the sample mean (assuming no packets are |
lost) would approach 0 (because the one-way-ipdv values must approach |
0). Note, however, that this says nothing about the shape of the |
distribution, or whether it is symmetric. Note further that over |
significant intervals, depending on the width of the interval [L,U), |
that the sample mean one-way-ipdv could be positive, negative or 0.
6.9. Some statistics for One-way-ipdv
Some statistics are suggested which can provide useful information in |
analyzing the behavior of the packets flowing from Src to Dst. The |
focus is on the instantaneous behavior of the connection. Other |
statistics can be defined if needed.
Demichelis and Chimento [Page 12]
INTERNET-DRAFT Packet Delay Variation June 1999
6.9.1. Type-P-One-way-ipdv-inverse-percentile
Given a Type-P-One-way-ipdv-Stream and a time threshold, that can be
either positive or negative, the fraction of all the ipdv values in
the Stream less than or equal to the threshold, if the threshold is
positive, or greater or equal to the threshold if the threshold is
negative.
For many real-time services that require a regular delivery of the
packets, this statistics can give the amount of packets received
beyond acceptable limits.
6.9.2. Type-P-One-way-ipdv-jitter |
This metric was defined in [7] and is simply the absolute value of |
the Type-P-One-way-ipdv. This can be used to derive a number of |
metrics. |
7. Discussion on clock synchronization
This section gives some considerations about the need of having
synchronized clocks at Src and Dst. These considerations are given as
a basis for discussion, they require further investigation. We start
from the analysis of the mean value of the ipdv distribution related
to a "continuous" sample. Some more detailed calculations are
presented in Appendix A.
7.1. Effects of synchronization errors
We refer here to the two components that can generate this type of
errors that are the reciprocal "skew" and "drift" of the Src and Dst
clocks. It is first of all noted that the variable component "drift"
is physically limited and its effects can be interpreted by saying
that the total reciprocal skew of the two clocks can vary, ranging
from a min to a max. value in the time. This type of variation takes
place very slowly being mostly connected to variations in
temperature.
We suppose to perform a measurement between a Src and a Dst that have
a reciprocal, initial skew of "ts1" and a reciprocal drift such that,
after the time T the total skew is "ts2". It is not here a limitation
to consider that at the beginning of time T the two clocks indicate
the same time T0.
Demichelis and Chimento [Page 13]
INTERNET-DRAFT Packet Delay Variation June 1999
In order to analyze the effects produced by this situation we suppose
that packets are transferred, from Src to Dst, with a constant delay
D In this conditions the measured ipdv should always be zero, and
what is actually measured is the error.
An ipdv value is measured at the beginning of time T with two packets
having an interval of Ti(1).Another ipdv value is measured at the end
of T with two packets having a time interval Ti(2).
On our purposes other errors (like wire-time vs host-time) are not
considered since they are not relevant in this analysis, being common
to all the measurement methods.
It is then possible to calculate the values of the Tx and Rx
timestamps as they are seen by the two clocks, and the related two
ipdv values.
The first ipdv value will be: ipdv1 = ts1*Ti(1) + ((ts2-ts1)/T)*Ti(1)
The second ipdv value will be: ipdv2 = ts2*Ti(2) +((ts2-ts1)/T)*Ti(2)
The error is given by the effect of the skew during the time interval
Ti(i) between the two packets of the pair, and a second order term
due to the variation of that skew in the same interval.
If, as in the most of practical cases, the drift can be considered
close to zero, then ts1 = ts2, and the error is not depending on the
time at which the measurement is done. In addition, this type of
error can be corrected as it is indicated in the next paragraph and
discussed in Appendix A.
In any case the maximum error on an ipdv value will correspond to the
effect of the maximum reciprocal skew on the maximum interval between
packets.
7.2. Related precision
This means that:
+ If the skew is constant and is = ts all the ipdv(i) values are
increased by the quantity Ti(i)*ts with respect the actual value.
The mean ipdv value will therefore increased of the quantity
E[Ti(i)]*ts, which is measured. Also E[Ti(i)] can be measured, and
should be related to lambda. That means that the skew ts can be
calculated. If together with ipdv(i), also the corresponding Ti(i)
are collected, for each ipdv(i) value a correcting term is
available, and a sample of "corrected" c-ipdv(i) values is
obtained, where c-ipdv(i) = ipdv(i) - Ti(i)*st.
Demichelis and Chimento [Page 14]
INTERNET-DRAFT Packet Delay Variation June 1999
+ Considering the total skew as subdivided into a fixed part and a
variable part (skew and drift),respectively, ts and + or - td,
from the mean ipdv value and the mean emission interval the
average skew can be derived in the period of interest (Appendix
A). The preceding correction can then be applied. The maximum
residual error on an ipdv value is given by the difference between
the actual skew at the time in which the value has been measured
and the average skew, multiplied by the time interval between the
packets that have generated that ipdv value. Considerations on the
number of values in the sample affected by errors are reported in
Appendix A.
+ If the duration of the measurement is such that it is possible to |
consider that the ipdv (without skew) is close to zero, the mean
value of the ipdv distribution will have the value of the average
skew multiplied by the mean value of the emission interval, as
supposed above.
+ We observe that the displacement due to the skew does not change
the shape of the distribution, and, for example the Standard
Deviation remains the same. What introduces a distortion is the
effect of the drift, also when the mean value of this effect is
zero at the end of the measurement. The value of this distortion
is limited to the effect of the total skew variation on the
emission interval.
+ In what has been said, skew and drift have been considered as
"reciprocal". In Appendix A it will be considered that each of the
two clocks have a skew and a drift with respect a "true time", and
it will be observed that the difference is negligible with respect
the situation in which one of the two clocks is taken as the "true
time".
8. Definition for a bidirectional ipdv metric
We now consider that the action of the skew on one direction is the
same, with opposite sign, of the action on the other direction. The
idea of performing at the same time two independent measurements in
the two directions is suggested by this fact.
If, after a long measurement, the variable conditions of the system
under test have reached the situation of a contribution close to zero
to the mean value of the ipdv distribution, it is expected that only
the action of the average skew has modified the measured mean value.
It is therefore expected that on one direction that value is equal
and opposite to the one measured in the other direction.
Demichelis and Chimento [Page 15]
INTERNET-DRAFT Packet Delay Variation June 1999
This fact offers the possibility of defining a theoretical reference
measurement duration in the following way:
The reference duration of a bidirectional ipdv measurement between an
host E and an host W is reached at time Tf such that for each time T
> Tf the expression ABS(E(ipdv E-W) - E(ipdv W-E))< epsilon, where
epsilon is what we can consider as zero, is always verified. This is
one, but not the only method for verifying that the mean ipdv value
has reached the value of the average reciprocal skew.
At this point it is possible to evaluate the reciprocal skew. This
will require the knowledge of the mean value of the intervals between
consecutive packets, that can be calculated over the transmitted
stream, by using the collected time stamps.
A bidirectional measurement can be defined not only as twin one-way
independent metrics that take place (nearly) at the same time, but
also as a two-way metric making use of packets looped back at one
end. This metric, that can be object of further study/Draft, would be
able to measure also the Round Trip Delay and its variations.
Problems will anyway arise on the characterization of emission
intervals in the backward direction. They would be produced by the
combination of the original Poisson arrival process and the effect of
ipdv on the forward direction. It has to be studied if this sequence
of intervals is still suitable for the measurement. also other
possibilities can be envisaged for obtaining a proper backward
sequence and still maintain the loopback concept.
9. Relationship to other standards |
The ITU definitions are based on delay variation as defined for ATM |
cells [5]. We will discuss these briefly first and then discuss the |
ITU's definition for IP packets [3]. |
9.1. 1-Point Cell Delay Variation |
The ITU looks at cell delay variation from two different points of |
view. The first, called 1-point cell delay variation, is essentially |
a measure of how a cell stream varies from a stated cell rate (e.g. |
the peak cell rate). The basic idea behind the measurement is as |
follows: The observer at the measurement point notes cell arrival |
times and clock ticks. The clock ticks at a constant rate, based on |
the peak cell rate for the cell stream. The difference between the |
cell arrival times and the clock ticks is the 1-point cell delay |
variation. If a cell arrives later than the clock tick, the clock |
"restarts" at the actual cell arrival time, and continues to tick at |
Demichelis and Chimento [Page 16]
INTERNET-DRAFT Packet Delay Variation June 1999
a constant rate from that point. |
The purpose of this measure is to identify what is called "cell |
clumping" and non-conforming cells. That is, to idenify cells that |
violate the leaky bucket parameters defined for that cell stream. |
That is why the clock skips when a cell is later than the normal |
inter-cell time defined by the peak cell rate. It is of much less |
interest when cells are late than when they arrive too close |
together. |
9.2. 2-Point Delay Variation, Cells and Packets |
2-Point cell delay variation, as defined in [5] is closer to what is |
defined here. The basic idea behind this metric is that two |
measurement points, whose clocks are synchronized, observe a cell |
stream and timestamp when each cell passes. The difference in the |
timestamps for a cell is essentially the one-way delay. There is also |
assumed to be a one-way cell delay for a reference cell which we will |
denote d0. The cell delay variation for the ith cell is then di-d0. |
Note that this is not an absolute value, but that the cell delay |
variation can be either positive or negative. [5] does not specify |
how to choose the reference cell delay. |
In [3] there is an informative appendix describing packet delay |
variation, which means that the material is not binding as a |
standard. The definitions are very similar to [5] with "packet" |
subsituting for "cell" in most places. One difference is that [3] |
offers two ways to define the reference packet (with the default |
being the first): |
+ Take the delay of the first packet of the sequence as the |
reference time. |
+ Take the average one-way packet delay as the reference time. |
9.3. Discussion |
9.3.1. Differences |
Demichelis [4] points out a number of problems with the 2-point PDV |
definition in [3]. First of all is the issue of choosing the |
reference delay time. If this is chosen arbitrarily, it becomes |
uncertain how to compare the measurements taken from two non- |
overlapping periods. If it is chosen as an average, that can also be |
Demichelis and Chimento [Page 17]
INTERNET-DRAFT Packet Delay Variation June 1999
a problem, because over long periods of time in a network, the |
average one-way delay can vary widely. A twenty-four hour average as |
the reference time can seriously overestimate the actual delay |
variation at a given time of day because the night-time hours, when |
the delay can be expected to approach the propagation and node time, |
is included in the average. On the other hand, there is no clear way |
to partition the time in order to find averages for certain periods |
of time and compute the delay variation with reference to these |
averages. |
Another problem pointed out in [4] is the fact that 2-point PDV |
requires synchronized clocks, whereas in this document Demichelis |
shows that synchronized clocks are not absolutely necessary for ipdv. |
9.3.2. Relationship between the metrics |
The ipdv metric described here and the 1-point cell delay variation |
metric described in [5] do not really have much in common (see also |
[4]). 1-point delay variation is really intended to talk about the |
relationship of cell arrival times to a given periodic event, and |
consequently is more closely related to the first definition of |
"jitter" given in Section 3 above. |
2-point delay variation (actually, the packet variant described in |
[3]) is related to ipdv, and this relationship can be made precise as |
follows: Suppose that an arbitrarily chosen packet is designated as |
the reference packet for the 2-point measurement and also as the |
start packet of the ipdv measurement. Denote this packet by p(0). |
Then given ipdv measurements for a series of packets, the 2-point |
delay variation for packet i is p(0) + the sum from k=1 to i of |
ipdv(k). |
Similarly, given a sequence of 2-point delay variation measurements |
we can derive the ipdv measurement as follows: Denote the 2-point |
delay variation measurement for packet i as v(i). Then the ipdv value |
for the pair of packets p(k-1), p(k) is simply v(k)-v(k-1) [6]. |
9.3.3. Summary |
As described above, there are a number of disadvantages of the |
2-point packet delay variation approach. Further, the ipdv approach |
described here is general enough to provide the same information as |
the 2-point packet delay variation measurements. Because of this, and |
because of the (possibly) looser clock synchronization requirements |
of ipdv, we recommend the one-way-ipdv approach for the delay |
variation measurement. |
Demichelis and Chimento [Page 18]
INTERNET-DRAFT Packet Delay Variation June 1999
10. Security Considerations |
The one-way-ipdv metric has the same security properties as the one- |
way-delay metric [2]. The packets contain no user information, and so |
privacy of user data is not a concern. It is still possible that |
there could be an attempt at a denial of service attack by sending |
many measurement packets into the network; there could also be |
attempts to disrupt measurements by diverting packets or corrupting |
them. |
In general, legitimate measurements must have their parameters |
selected carefully in order to avoid interfering with normal traffic |
in the network. Such measurements should also be authorized and |
authenticated in some way so that attacks can be identified and |
intercepted. |
11. Acknowledgements |
Thanks to Matt Zekauskas from Advanced and Ruediger Geib from |
Deutsche Telekom for discussions relating to the contents of this |
revised draft. |
12. References |
[1] V.Paxon, G.Almes, J.Mahdavi, M.Mathis - "Framework for IP |
Performance Metrics", RFC 2330 Feb. 1998 |
[2] G.Almes, S.Kalidindi - "A One-Way-Delay Metric for IPPM", |
Internet Draft <draft-ietf-ippm-delay-07.txt> May 1999 |
[3] Draft New ITU-T Recommendation I.380 "Internet Protocol Data |
Communication Service - IP Packet Transfer and Availability |
Performance Parameters" |
[4] Demichelis, Carlo - "Packet Delay Variation Comparison between |
ITU-T and IETF Draft Definitions" March 1999 |
[5] ITU-T Recommendation I.356 "B-ISDN ATM Layer Cell Transfer |
Performance" |
[6] e-mail exchanges with Ruediger Geib |
[7] V. Jacobson, K. Nichols, K. Poduri - "An expedited forwarding |
PHB", Internet Draft, November 1998 <draft-ietf-diffserv-phb- |
ef-01.txt> |
Demichelis and Chimento [Page 19]
INTERNET-DRAFT Packet Delay Variation June 1999
13. Authors' Addresses |
Carlo Demichelis <carlo.demichelis@cselt.it>
CSELT - Centro Studi E Laboratori Telecomunicazioni S.p.A
Via G. Reiss Romoli 274
10148 - TORINO
Italy
Phone +39 11 228 5057
Fax. +39 11 228 5069
Philip Chimento <chimento@ctit.utwente.nl>
CTIT - Centre for Telematics and Information Technology
University of Twente
Postbox 217
7500 AE Enschede
The Netherlands
Phone +31 53 489 4331
FAX +31 53 489 4524
APPENDIX A
This Appendix considers the scenario in which two hosts have clocks
that are both not synchronized. Between the two hosts, in an
independent way and at the same time in both direction an ipdv
measurement is performed according the methodology that is described
in the main body of this Draft. This hypothetical scenario is only
supposed for discussing the theory and the characteristics of the
ipdv metric and its results, without considering implementation
issues.
14. Initial positions
The two hosts will be called West (W) and East (E). The two
measurements start at the same time, while the end of the measurement
it is supposed to be decided by the results of the measurement
itself.
At the beginning of the measurement the time declared by the West
clock is T0w, the time declared by the East clock is T0e, while the
true time is T0t.
The W-clock is affected by an absolute skew of skw ppm and the E-
clock by an absolute skew of skw ppm.
Demichelis and Chimento [Page 20]
INTERNET-DRAFT Packet Delay Variation June 1999
The W-clock is affected by an absolute drift ranging from -drw ppm to
+drw ppm, the E-clock by an absolute drift ranging from -dre ppm to
+dre ppm.
14.1. Evaluation of skew and drift effects
In order to evaluate the effect of the drift on this type of metric,
it is necessary to consider the time in which the variation of the
skew takes place. We consider the two extreme cases in which the
variation takes place uniformly from the beginning to the end of the
measurement and the variation takes place suddenly at a generic time
along the measurement. Let TM be the measurement time.
14.1.1. Mean ipdv value
Since the mean ipdv value, as it has been seen, is the difference of
the last delay minus the first, divided by the number of considered
values, we consider what, in the two cases, is measured for first and
last delay.
We call trueDf the true first Delay and trueDl the true last Delay.
For the evaluation that we want to do, it is not a limitation to
consider that they are equal and have a value of trueD. We also
consider as time 0 the true time at which the transmission of the
first packet starts from West toward East.
In case of continuous drift we define a "drift per second" as: drpsW
= 2*drw / TM and drpsE = 2*dre / TM along the measurement this
will bring the skew from a value of: skWmin = skw - drw ;
skEmin = ske - dre to a value of skWmax = skw + drw ; skEmax =
ske + dre
What is measured as first Delay is:
measured first Rx time - measured first Tx time OffsetEast + trueD*[1
+ skEmin + (1/2)*drpsE] - OffsetWest
What is measured as last Delay is:
measured last Rx time - measured last Tx time OffsetEast + (TM +
trueD)*[1 + skEmin + (1/2)*2*dre] -
- OffsetWest - TM*[1 + skWmin + (1/2)*2*drw]
The difference between the last and first Delay is therefore:
TM*(skEmin - skWmin + dre - drw) - trueD*drpsE/(2*TM)
Demichelis and Chimento [Page 21]
INTERNET-DRAFT Packet Delay Variation June 1999
if TM = 10 hours drpsE is in the order of 50*10E-6 / 36000 that is
about 10E-9 and the second term of the expression is in the order of
10E-14 for true delays in the order of 1 sec (negligible term). We
consider that, with very good approximation:
Mean emission interval (mti) = TM / number of ipdv values (N)
Therefore:
mean ipdv = (measured last Delay - measured first Delay) / N =
= mti*(skEmin - skWmin + dre - drw)
but we considered skEmin = ske - dre and skWmin = skw - drw and
therefore:
mean ipdv = (meas.lastD - meas.firstD) / mti*(reciprocal mean skew)
The previous procedure is now applied to the case in which the total
drift takes place in a very short time. Some cases are possible, and
we consider the one in which at the beginning the West clock has
skWmax and the East clock has skEmin, at time txW the West clock
assumes skWmin and at time txE the East clock assumes skEmax. What
is measured as first Delay is now:
measured first Rx time - measured first Tx time OffsetEast + trueD*(1
+ skEmin) - OffsetWest
What is measured as last Delay is:
measured last Rx time - measured last Tx time + OffsetEast + txE*(1 +
skEmin) + (TM - txE)*(1 + skEmax) + + trueD*(1 + skEmax) - -
OffsetWest - txW*(1 + skWmax) - (TM - txW)*(1 + skWmin)
but the mean skew values will be:
mskw = [skWmax*txW + skWmin*(TM - txW)] / TM mske = [skEmin*txE +
skEmax*(TM - txE)] / TM
the difference between the two delays therefore is:
TM*(mske - mskw) + 2*trueD*dre
and the mean ipdv value will be:
mean ipdv = mti*(mske - mskw) + 2*mti*trueD*dre/TM
the second term of the second member in the previous hypotheses is in
the order of the nanosecond, and we neglect it. Also in this case,
from the mean ipdv value, and knowing the mean emission interval, the
Demichelis and Chimento [Page 22]
INTERNET-DRAFT Packet Delay Variation June 1999
relative skew of the clocks can be obtained.
More in general, independently on how the drift acts inside its
limits, we assert that always the mean ipdv value divided by the mean
emission interval produces the value of the mean reciprocal skew of
the two clocks, provided that the collected number of ipdv values is
significant for the statistics.
14.1.2. Errors and corrections
If the drift is always close to zero, it is possible to obtain the
true value of the reciprocal skew and correct all the ipdv values.
Each of them is associated to an emission interval ti between the two
packets that have produced the value itself. Then a better ipdv value
will be: corr.ipdv(i) = meas.ipdv(i) - ti * skew This is a better
value but not exactly the true one, since we supposed that both
clocks are not synchronized to the true time. Two errors are
affecting the corrective terms which are:
+ The reciprocal skew is measured as referred to the Src clock
+ The interval ti is measured by the Src clock.
These are second order errors since the measured skew will be
affected by a "relative" error in the order of the Src skew, an the
same is for the error affecting the ti value.
If the drift is significant and it can range from the lower to the
upper limit of its field, the measured average of the skew will
depend on the type of variation. Some cases are considered that
demonstrate that actually the proposed correction is not so much
effective in this case. Only the fixed part of the total clock
variation can be properly corrected.
14.1.3. Constant drift
The first case is the first one considered in the preceding
paragraph, where the drift is uniform. We suppose that a reciprocal
skew is measured and used for correction.
At the beginning of the measurement the actual reciprocal skew is:
init.skew = mean.skew - rel.max.drift
and at the end the actual reciprocal skew is:
Demichelis and Chimento [Page 23]
INTERNET-DRAFT Packet Delay Variation June 1999
final.skew = mean.skew + rel max.drift
The correction is effective only in the central part of the
measurement. At the beginning and at the end a residual error will
affect the ipdv values whose value will be:
ipdv(i).err = ti * rel.max.drift
We underline here that the error is larger for large intervals ti and
lower for short intervals ti. For intervals derived from a poissonian
arrival process, there are many short intervals and few large
intervals. We also note that a constant drift cannot last
indefinitely, since there is a minimum and a maximum for the skew.
14.1.4. Step of drift
In this case the error profile depends on the time at which the drift
changes. If the change is near the beginning or near the end of the
measurement, the calculated mean skew will be very close to the
actual skew of the largest part of the measurement. On that part the
correction will be effective, while over the remaining few values the
error will be twice with respect the preceding case. The worse
condition is produced by a change in drift in the middle of the
measurement. In this case the correction would be useful only if the
drift was significantly less than the skew.
14.2. Comparison with a synchronized case
In this section we consider a case in which the two hosts have
synchronized clocks, and the synchronization is obtained by setting
the real time each second in each of the clocks. We optimistically
suppose that this is done exactly (without any imprecision). On the
clocks, anyway skew and drift continue to act. We refer to reciprocal
skew and drift, having already seen that this is significant. We
suppose to perform an ipdv measurement and we evaluate what is
measured by the mean ipdv value and what is the error on the measured
ipdv values.
We notice, first of all, that nothing changes for ipdv values
measured over intervals falling completely between two
synchronization instants. In this case, the effect of
synchronization is only to put to zero the offset, that does not
appear in the calculation of ipdv values.
Something different happens if the synchronization instant (or more
Demichelis and Chimento [Page 24]
INTERNET-DRAFT Packet Delay Variation June 1999
synchronization instants) falls inside the interval. In this case the
error can range from + to - the error related to one second interval,
or, more in general, from + to - the error related to an interval
equal to the synchronization period. The (few) large intervals will
produce a limited error while the (many) short intervals will
continue to produce errors of the same order of magnitude of the not
synchronized case.
Besides, even if the drift is negligible, the mean ipdv value is no
more suitable to calculate the skew, and it will be much more close
to zero. Therefore it is no more possible to correct the distortion
of the distribution.
Finally, it is necessary to add to these errors the unavoidable
imprecision of the synchronization process. We have to consider that
the magnitude of errors introduced by skew and drift is in the order
of tenth of microseconds. Not always the complete synchronization
process has a better precision.
14.3. Bidirectional measurement and components of ipdv
Three terms have been described that can displace the mean ipdv value
from zero. They are:
+ The total skew, already discussed above, that always acts in an
equal way and opposite direction over the two directions between
West and East hosts.
+ The effect of varying traffic that can increase or decrease along
limited periods, the average value of the One-Way-Delay. The
metric above presented supposes that the measurement period is
large enough for considering this effect as tending to zero. It
is explicitly noted that the effect will produce a zero effect
only on the mean ipdv value, while the effect on values ipdv(i) is
always present. This is not a distortion of the distribution,
since is part of the variation that is measured. This effect is
different, and usually concordant, on the two directions.
+ The difference between first and last instantaneous values of the
delay variation, that tends to zero when the number of collected
ipdv values becomes large.
In order to isolate the last two effects, we consider here a
measurement over a long period (e.g. 24 hours)where the drift is
negligible, and the effect of the skew has been corrected.
Demichelis and Chimento [Page 25]
INTERNET-DRAFT Packet Delay Variation June 1999
14.4. Slow variation in a given period
The packets of the stream can be represented on a system of cartesian
orthogonal axes with transmission time on x-axis and reception time
on y-axis, by points localized by transmission and reception time of
each packet. Considering an arbitrary period of time Tper, which will
be a parameter of this procedure, it can be taken as a sliding window
over the sample and for each position of this window, established by
successive packets, the segment of straight line is calculated that
best approximate the points, by means of a linear regression method.
The slope of this segment will be one if along the period the delay
has not changed, and different from one if that delay has increased
(>1) or decreased (<1). For each position of the window it is
therefore possible to find a value of "slow delay variation" with
Tper as a parameter. This will give an indication on variations
produced by different traffic conditions along the measurement
period. This item can be subject for further study.
At the same time this procedure offers a criterion for reducing the
error introduced in the calculation of the mean ipdv by the
instantaneous component of the difference between last and first
delay. Supposing that the timestamps, on which the metric is based,
are collected and then processed, if the method of the sliding window
is applied at the beginning and at the end of the collected sample,
it is possible to avoid starting and ending the measurement on values
possibly too different from the average (points too far away from the
calculated straight line). |
Expiration date: December, 1999
Demichelis and Chimento [Page 26]
| PAFTECH AB 2003-2026 | 2026-04-24 07:36:25 |