One document matched: draft-ietf-ipngwg-scoped-routing-02.txt
Differences from draft-ietf-ipngwg-scoped-routing-01.txt
IPNGWG Working Group B. Haberman
Internet Draft Nortel Networks
draft-ietf-ipngwg-scoped-routing-02.txt
November 1999
Expires May 2000
Routing of Scoped Addresses
in the Internet Protocol Version 6 (IPv6)
Status of this Memo
This document is an Internet-Draft and is in full conformance with all
provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet Engineering Task
Force (IETF), its areas, and its working groups. Note that other groups
may also distribute working documents as Internet-Drafts. Internet-
Drafts are draft documents valid for a maximum of six months and may be
updated, replaced, or obsoleted by other documents at any time. It is
inappropriate to use Internet- Drafts as reference material or to cite
them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Abstract
This document outlines a mechanism for generating forwarding tables
that include scoped IPv6 addresses. It defines a set of rules for
routers to implement in order to forward packets addressed to scoped
unicast or multicast addresses regardless of the routing protocol.
These rules apply to all scoped addresses.
1.
Introduction
This document defines a set of rules for the generation of forwarding
table entries for scoped addresses. These rules will describe the
handling of scoped addresses for both single site and site boundary
routers. These rules apply to all routing protocols that support IPv6
addresses.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC 2119].
2.
Assumptions and Definitions
This document makes several assumptions concerning sites:
- Links belong to at most one site
- Interfaces belong to the site of the attached link, if any
Haberman 1
Internet Draft Routing of Scoped IPv6 Addresses November 1999
- Nodes are a part of all sites which their interfaces belong to,
and no other sites
- Site boundaries are identical for unicast and multicast traffic
- A single interface can be in at most one site
- Each interface participating in a site has a site identifier
- In the absence of explicit configuration, all site identifiers on
a node default to the same value
A single site router is defined as a router configured with the same
site identifier on all interfaces. A site boundary router is defined
as a router that has at least 2 distinct site identifiers.
* *
* *
* Site ID = X *
* *
+-*---|-------|---*-+
| * i/f 1 i/f 2 * |
| *************** |
| |
| |
| Router |
******************* *******************
| * * |
Site ID = Y -i/f 3 * * i/f 4- Site ID = Default
| * * |
******************* *******************
+-------------------+
Figure 1: Multi-Sited Router
3.
Single Site Routing
In a single site router, a routing protocol can advertise and route all
addresses and prefixes, except the link-local prefixes, on all
interfaces. This configuration does not require any special handling
for site local addresses. The reception and transmission of site local
addresses is handled in the same manner as globally scoped addresses.
This applies to both unicast and multicast routing protocols.
4.
Site Boundary Unicast Routing
With respect to site boundaries, routers must consider which interfaces
a packet can be transmitted on as well as control the propagation of
routing information specific to the site. This includes controlling
which prefixes can be advertised on an interface.
4.1 Routing Protocols
When a routing protocol determines that it is a site boundary router,
it must perform additional work in order to protect inter site
integrity and still maintain intra site connectivity.
Haberman 2
Internet Draft Routing of Scoped IPv6 Addresses November 1999
In order to maintain connectivity, the routing protocol must be able to
create forwarding information for the global prefixes as well as for
all of the site prefixes for each of its attached sites. The most
straightforward way of doing this is to create up to (n+1) forwarding
tables; one for the global prefixes, if any, and one for each of the
(n) sites.
To protect inter site integrity; routers must be selective in the
forwarding information that is shared with neighboring routers.
Routing protocols routinely transmit their routing information to its
neighboring routers. When a router is transmitting this routing
information, it must not include any information about sites other than
the site defined on the interface used to reach a neighbor.
As an example, the router in Figure 1 must advertise routing
information on four interfaces. The information advertised is as
follows:
- Interface 1
- All global prefixes
- All site prefixes learned from Interfaces 1 and 2
- Interface 2
- All global prefixes
- All site prefixes learned from Interfaces 1 and 2
- Interface 3
- All global prefixes
- All site prefixes learned from Interface 3
- Interface 4
- All global prefixes
- No site prefixes
By imposing advertisement rules, site integrity is maintained by
keeping all site routing information contained within the site.
4.2 Packet Forwarding
In addition to the extra cost of generating additional forwarding
information for each site, site boundary routers must also do some
additional checking when forwarding packets that contain site local
addresses.
If a packet being forwarded contains a site local destination address,
regardless of the scope of the source address, the router must perform
the following:
- Lookup incoming interface's site identifier
- Perform route lookup for destination address in arrival
interface's site scoped routing table
If a packet being forwarded contains a site local source address and a
global scoped destination address, the following must be performed:
- Lookup outgoing interface's site identifier
- Compare inbound and outbound interfaces' site identifiers
If the site identifiers match, the packet can be forwarded. If they do
not match, an ICMPv6 destination unreachable message must be sent to
Haberman 3
Internet Draft Routing of Scoped IPv6 Addresses November 1999
the sender with a code value, code = 2 (beyond scope of source
address).
5.
Scoped Multicast Routing
With IPv6 multicast, there are multiple scopes supported. Multicast
routers must be able to control the propagation of scoped packets based
on administratively configured boundaries.
5.1 Routing Protocols
Multicast routing protocols must follow the same rules as the unicast
protocols. They will be required to maintain information about global
prefixes as well as information about all scope boundaries that exist
on the router.
Multicast protocols that rely on underlying unicast protocols for route
exchange (i.e. PIM, MOSPF) will not suffer as much of a performance
impact since the unicast protocol will handle the forwarding table
generation. They must be able to handle the additional scope
boundaries used in multicast addresses.
Multicast protocols that generate and maintain their own routing tables
will have to perform the additional route calculations for scope
boundaries. All multicast protocols will be forced to handle fourteen
additional scooping identifiers above the site identifiers supported in
IPv6 unicast addresses.
5.2 Packet Forwarding
The following combinations describe the forwarding rules for multicast:
- Global multicast destination / Global unicast source
- Global multicast destination / Site local unicast source
- Scoped multicast destination / Global unicast source
- Scoped multicast destination / Site local unicast source
The first combination requires no special processing over what is
currently in place for global IPv6 multicast. The remaining
combinations should result in the router performing the same
identifiers check as outlined for the site local unicast addresses.
Since IPv6 multicast supports fifteen unique multicast scopes, it is
assumed that scopes 0x1 through 0x4 are strictly less than the unicast
site scope, scope 0x5 (site) is equal to the unicast site scope, scopes
0x6 through 0xd are strictly greater than the unicast site scope and
strictly less than the unicast global scope, and scope 0xe is equal to
the unicast global scope.
6.
Protocol Impact
The performance impact on routing protocols is obvious. Routers
implementing scoped address support will be forced to perform an
additional check in the main forwarding path to determine if the source
address is a site-local address. This will add overhead to the
processing of every packet flowing through the router. In addition,
Haberman 4
Internet Draft Routing of Scoped IPv6 Addresses November 1999
there will be some storage overhead for the scope identifiers. If
scoped addresses are going to be realized, this performance impact may
be acceptable.
7.
Security Considerations
This document specifies a set of guidelines that allow routers to
prevent site-specific information from leaking out of each site. If
site boundary routers allow site routing information to be forwarded
outside of the site, the integrity of the site could be compromised.
8.
References
[RFC 2119] S. Bradner, "Key words for use in RFCs to Indicate
Requirement Levels", RFC 2119, BCP14, March 1999.
Acknowledgements
The author would like to thank Thomas Narten, Steve Deering, Erik
Nordmark, and Matt Crawford for their comments and reviews of this
document.
Haberman 5
Author's Address
Brian Haberman
Nortel Networks
4309 Emperor Blvd.
Suite 200
Durham, NC 27703
1-919-992-4439
Email : haberman@nortelnetworks.com
Haberman 6
| PAFTECH AB 2003-2026 | 2026-04-23 06:20:24 |