One document matched: draft-ietf-ipfix-anon-06.txt
Differences from draft-ietf-ipfix-anon-05.txt
IPFIX Working Group E. Boschi
Internet-Draft B. Trammell
Intended status: Experimental ETH Zurich
Expires: July 23, 2011 January 19, 2011
IP Flow Anonymization Support
draft-ietf-ipfix-anon-06.txt
Abstract
This document describes anonymization techniques for IP flow data and
the export of anonymized data using the IPFIX protocol. It
categorizes common anonymization schemes and defines the parameters
needed to describe them. It provides guidelines for the
implementation of anonymized data export and storage over IPFIX, and
describes an information model and Options-based method for
anonymization metadata export within the IPFIX protocol or storage in
IPFIX Files.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on July 23, 2011.
Copyright Notice
Copyright (c) 2011 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
Boschi & Trammell Expires July 23, 2011 [Page 1]
Internet-Draft IP Flow Anonymization Support January 2011
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1. IPFIX Protocol Overview . . . . . . . . . . . . . . . . . 4
1.2. IPFIX Documents Overview . . . . . . . . . . . . . . . . . 5
1.3. Anonymization within the IPFIX Architecture . . . . . . . 5
1.4. Supporting Experimentation with Anonymization . . . . . . 6
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 6
3. Categorization of Anonymization Techniques . . . . . . . . . . 7
4. Anonymization of IP Flow Data . . . . . . . . . . . . . . . . 8
4.1. IP Address Anonymization . . . . . . . . . . . . . . . . . 10
4.1.1. Truncation . . . . . . . . . . . . . . . . . . . . . . 11
4.1.2. Reverse Truncation . . . . . . . . . . . . . . . . . . 11
4.1.3. Permutation . . . . . . . . . . . . . . . . . . . . . 11
4.1.4. Prefix-preserving Pseudonymization . . . . . . . . . . 12
4.2. MAC Address Anonymization . . . . . . . . . . . . . . . . 12
4.2.1. Truncation . . . . . . . . . . . . . . . . . . . . . . 13
4.2.2. Reverse Truncation . . . . . . . . . . . . . . . . . . 13
4.2.3. Permutation . . . . . . . . . . . . . . . . . . . . . 14
4.2.4. Structured Pseudonymization . . . . . . . . . . . . . 14
4.3. Timestamp Anonymization . . . . . . . . . . . . . . . . . 15
4.3.1. Precision Degradation . . . . . . . . . . . . . . . . 15
4.3.2. Enumeration . . . . . . . . . . . . . . . . . . . . . 16
4.3.3. Random Shifts . . . . . . . . . . . . . . . . . . . . 16
4.4. Counter Anonymization . . . . . . . . . . . . . . . . . . 16
4.4.1. Precision Degradation . . . . . . . . . . . . . . . . 17
4.4.2. Binning . . . . . . . . . . . . . . . . . . . . . . . 17
4.4.3. Random Noise Addition . . . . . . . . . . . . . . . . 17
4.5. Anonymization of Other Flow Fields . . . . . . . . . . . . 17
4.5.1. Binning . . . . . . . . . . . . . . . . . . . . . . . 18
4.5.2. Permutation . . . . . . . . . . . . . . . . . . . . . 18
5. Parameters for the Description of Anonymization Techniques . . 18
5.1. Stability . . . . . . . . . . . . . . . . . . . . . . . . 19
5.2. Truncation Length . . . . . . . . . . . . . . . . . . . . 19
5.3. Bin Map . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.4. Permutation . . . . . . . . . . . . . . . . . . . . . . . 20
5.5. Shift Amount . . . . . . . . . . . . . . . . . . . . . . . 20
6. Anonymization Export Support in IPFIX . . . . . . . . . . . . 20
6.1. Anonymization Records and the Anonymization Options
Template . . . . . . . . . . . . . . . . . . . . . . . . . 21
6.2. Recommended Information Elements for Anonymization
Metadata . . . . . . . . . . . . . . . . . . . . . . . . . 23
6.2.1. informationElementIndex . . . . . . . . . . . . . . . 23
Boschi & Trammell Expires July 23, 2011 [Page 2]
Internet-Draft IP Flow Anonymization Support January 2011
6.2.2. anonymizationTechnique . . . . . . . . . . . . . . . . 23
6.2.3. anonymizationFlags . . . . . . . . . . . . . . . . . . 25
7. Applying Anonymization Techniques to IPFIX Export and
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
7.1. Arrangement of Processes in IPFIX Anonymization . . . . . 28
7.2. IPFIX-Specific Anonymization Guidelines . . . . . . . . . 30
7.2.1. Appropriate Use of Information Elements for
Anonymized Data . . . . . . . . . . . . . . . . . . . 30
7.2.2. Export of Perimeter-Based Anonymization Policies . . . 31
7.2.3. Anonymization of Header Data . . . . . . . . . . . . . 32
7.2.4. Anonymization of Options Data . . . . . . . . . . . . 32
7.2.5. Special-Use Address Space Considerations . . . . . . . 34
7.2.6. Protecting Out-of-Band Configuration and
Management Data . . . . . . . . . . . . . . . . . . . 34
8. Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
9. Security Considerations . . . . . . . . . . . . . . . . . . . 39
10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 41
11. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 41
12. References . . . . . . . . . . . . . . . . . . . . . . . . . . 41
12.1. Normative References . . . . . . . . . . . . . . . . . . . 41
12.2. Informative References . . . . . . . . . . . . . . . . . . 42
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 43
Boschi & Trammell Expires July 23, 2011 [Page 3]
Internet-Draft IP Flow Anonymization Support January 2011
1. Introduction
The standardization of an IP flow information export protocol
[RFC5101] and associated representations removes a technical barrier
to the sharing of IP flow data across organizational boundaries and
with network operations, security, and research communities for a
wide variety of purposes. However, with wider dissemination comes
greater risks to the privacy of the users of networks under
measurement, and to the security of those networks. While it is not
a complete solution to the issues posed by distribution of IP flow
information, anonymization (i.e., the deletion or transformation of
information that is considered sensitive and could be used to reveal
the identity of subjects involved in a communication) is an important
tool for the protection of privacy within network measurement
infrastructures.
This document presents a mechanism for representing anonymized data
within IPFIX and guidelines for using it. It is not intended as a
general statement on the applicability of specific flow data
anonymization techniques to specific situations, or as a
recommendation of any particular application of anonymization to flow
data export. Exporters or publishers of anonymized data must take
care that the applied anonymization technique is appropriate for the
data source, the purpose, and the risk of deanonymization of a given
application.
It begins with a categorization of anonymization techniques. It then
describes applicability of each technique to commonly anonymizable
fields of IP flow data, organized by information element data type
and semantics as in [RFC5102]; enumerates the parameters required by
each of the applicable anonymization techniques; and provides
guidelines for the use of each of these techniques in accordance with
current best practices in data protection. Finally, it specifies a
mechanism for exporting anonymized data and binding anonymization
metadata to Templates and Options Templates using IPFIX Options.
1.1. IPFIX Protocol Overview
In the IPFIX protocol, { type, length, value } tuples are expressed
in Templates containing { type, length } pairs, specifying which {
value } fields are present in data records conforming to the
Template, giving great flexibility as to what data is transmitted.
Since Templates are sent very infrequently compared with Data
Records, this results in significant bandwidth savings. Various
different data formats may be transmitted simply by sending new
Templates specifying the { type, length } pairs for the new data
format. See [RFC5101] for more information.
Boschi & Trammell Expires July 23, 2011 [Page 4]
Internet-Draft IP Flow Anonymization Support January 2011
The IPFIX information model [RFC5102] defines a large number of
standard Information Elements which provide the necessary { type }
information for Templates. The use of standard elements enables
interoperability among different vendors' implementations.
Additionally, non-standard enterprise-specific elements may be
defined for private use.
1.2. IPFIX Documents Overview
"Specification of the IPFIX Protocol for the Exchange of IP Traffic
Flow Information" [RFC5101] and its associated documents define the
IPFIX Protocol, which provides network engineers and administrators
with access to IP traffic flow information.
"Architecture for IP Flow Information Export" [RFC5470] defines the
architecture for the export of measured IP flow information out of an
IPFIX Exporting Process to an IPFIX Collecting Process, and the basic
terminology used to describe the elements of this architecture, per
the requirements defined in "Requirements for IP Flow Information
Export" [RFC3917]. The IPFIX Protocol document [RFC5101] then covers
the details of the method for transporting IPFIX Data Records and
Templates via a congestion-aware transport protocol from an IPFIX
Exporting Process to an IPFIX Collecting Process.
"Information Model for IP Flow Information Export" [RFC5102]
describes the Information Elements used by IPFIX, including details
on Information Element naming, numbering, and data type encoding.
Finally, "IPFIX Applicability" [RFC5472] describes the various
applications of the IPFIX protocol and their use of information
exported via IPFIX, and relates the IPFIX architecture to other
measurement architectures and frameworks.
Additionally, "Specification of the IPFIX File Format" [RFC5655]
describes a file format based upon the IPFIX Protocol for the storage
of flow data.
This document references the Protocol and Architecture documents for
terminology, and extends the IPFIX Information Model to provide new
Information Elements for anonymization metadata. The anonymization
techniques described herein are equally applicable to the IPFIX
Protocol and data stored in IPFIX Files.
1.3. Anonymization within the IPFIX Architecture
According to [RFC5470], IPFIX Message anonymization is optionally
performed as the final operation before handing the Message to the
transport protocol for export. While no provision is made in the
architecture for anonymization metadata as in Section 6, this
Boschi & Trammell Expires July 23, 2011 [Page 5]
Internet-Draft IP Flow Anonymization Support January 2011
arrangement does allow for the rewriting necessary for comprehensive
anonymization of IPFIX export as in Section 7. The development of
the IPFIX Mediation [I-D.ietf-ipfix-mediators-framework] framework
and the IPFIX File Format [RFC5655] expand upon this initial
architectural allowance for anonymization by adding to the list of
places that anonymization may be applied. The former specifies IPFIX
Mediators, which rewrite existing IPFIX Messages, and the latter
specifies a method for storage of IPFIX data in files.
More detail on the applicable architectural arrangements for
anonymization can be found in Section 7.1
1.4. Supporting Experimentation with Anonymization
The intended status of this document is Experimental, reflecting the
experimental nature of anonymization export support. Research on
network trace anonymization techniques and attacks against them is
ongoing. Indeed, there is increasing evidence that anonymization
applied to network trace or flow data its own is insufficient for
many data protection applications as in [Bur10]. Therefore, this
document explicitly does not recommend any particular technique or
implementation thereof.
The intention of this document is to provide a common basis for
interoperable exchange of anonymized data, furthering research in
this area, both on anonymization techniques themselves as well as to
the application of anonymized data to network measurement. To that
end, the classification in Section 3 and anonymization export support
in Section 6 can be used to describe and export information even
about data anonymized using techniques that are unacceptably weak for
general application to production data sets on their own.
While the specification herein is designed to be implementation- and
technique-independent, open research in this area may necessitate
future updates to the specification. Assuming the future successful
application of this specification to anonymized data publication and
exchange, it may be brought back to the IPFIX working group for
further development and publication on the standards track.
2. Terminology
Terms used in this document that are defined in the Terminology
section of the IPFIX Protocol [RFC5101] document are to be
interpreted as defined there. In addition, this document defines the
following terms:
Boschi & Trammell Expires July 23, 2011 [Page 6]
Internet-Draft IP Flow Anonymization Support January 2011
Anonymization Record: A record, defined by the Anonymization
Options Template in section Section 6.1, that defines the
properties of the anonymization applied to a single Information
Element within a single Template or Options Template.
Anonymized Data Record: A Data Record within a Data Set containing
at least one Information Element with anonymized values. The
Information Element(s) within the Template or Options Template
describing this Data Record SHOULD have a corresponding
Anonymization Record.
Intermediate Anonymization Process: An intermediate process which
takes Data Records and and transforms them into Anonymized Data
Records.
Note that there is an explicit difference in this document between a
"Data Set" (which is defined as in [RFC5101]) and a "data set". When
in lower case, this term refers to any collection of data (usually,
within the context of this document, flow or packet data) which may
contain identifying information and is therefore subject to
anonymization.
Note also that when the term Template is used in this document,
unless otherwise noted, it applies both to Templates and Options
Templates as defined in [RFC5101]. Specifically, Anonymization
Records may apply to both Templates and Options Templates.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
3. Categorization of Anonymization Techniques
Anonymization, as described by this document, is the modification of
a data set in order to protect the identity of the people or entities
described by the data set from disclosure. With respect to network
traffic data, anonymization generally attempts to preserve some set
of properties of the network traffic useful for a given application
or applications, while ensuring the data cannot be traced back to the
specific networks, hosts, or users generating the traffic.
Anonymization may be broadly classified according to two properties:
recoverability and countability. All anonymization techniques map
the real space of identifiers or values into a separate, anonymized
space, according to some function. A technique is said to be
recoverable when the function used is invertible or can otherwise be
reversed and a real identifier can be recovered from a given
Boschi & Trammell Expires July 23, 2011 [Page 7]
Internet-Draft IP Flow Anonymization Support January 2011
replacement identifier. Techniques wherein the function used can
only be reversed using additional information, such as an encryption
key, or knowledge of injected traffic within the data set;
"recoverability" as used within this categorization does not refer to
recoverability under attack.
Countability compares the dimension of the anonymized space (N) to
the dimension of the real space (M), and denotes how the count of
unique values is preserved by the anonymization function. If the
anonymized space is smaller than the real space, then the function is
said to generalize the input, mapping more than one input point to
each anonymous value (e.g., as with aggregation). By definition,
generalization is not recoverable.
If the dimensions of the anonymized and real spaces are the same,
such that the count of unique values is preserved, then the function
is said to be a direct substitution function. If the dimension of
the anonymized space is larger, such that each real value maps to a
set of anonymized values, then the function is said to be a set
substitution function. Note that with set substitution functions,
the sets of anonymized values are not necessarily disjoint. Either
direct or set substitution functions are said to be one-way if there
exists no non-brute force method for recovering the real data point
from an anonymized one in isolation (i.e., if the only way to recover
the data point is to attack the anonymized data set as a whole, e.g.
through fingerprinting or data injection).
This classification is summarized in the table below.
+------------------------+-----------------+------------------------+
| Recoverability / | Recoverable | Non-recoverable |
| Countability | | |
+------------------------+-----------------+------------------------+
| N < M | N.A. | Generalization |
| N = M | Direct | One-way Direct |
| | Substitution | Substitution |
| N > M | Set | One-way Set |
| | Substitution | Substitution |
+------------------------+-----------------+------------------------+
4. Anonymization of IP Flow Data
In anonymizing IP flow data as treated by this document, the goal is
generally two-way address untraceability: to remove the ability to
assert that endpoint X contacted endpoint Y at time T. Address
untraceability is important as IP addresses are the most suitable
field in IP flow records to identify real-world entities. Each IP
Boschi & Trammell Expires July 23, 2011 [Page 8]
Internet-Draft IP Flow Anonymization Support January 2011
address is associated with an interface on a network host, and can
potentially be identified with a single user. Additionally, IP
addresses are structured identifiers; that is, partial IP address
prefixes may be used to identify networks just as full IP addresses
identify hosts. This leads IP flow data anonymization to be
concerned first and foremost with IP address anonymization.
Any form of aggregation which combines flows from multiple endpoints
into a single record (e.g., aggregation by subnetwork, aggregation
removing addressing completely) may also provide address
untraceability; however, anonymization by aggregation is out of scope
for this document. Additionally of potential interest in this
problem space but out of scope are anonymization techniques which are
applied over multiple fields or multiple records in a way which
introduces dependencies among anonymized fields or records. This
document is concerned solely with anonymization techniques applied at
the resolution of single fields within a flow record.
Even so, attacks against these anonymization techniques use entire
flows and relationships between hosts and flows within a given data
set. Therefore, fields which may not necessarily be identifying by
themselves may be anonymized in order to increase the anonymity of
the data set as a whole.
Due to the restricted semantics of IP flow data, there is a
relatively limited set of specific anonymization techniques available
on flow data, though each falls into the broad categories discussed
in the previous section. Each type of field that may commonly appear
in a flow record may have its own applicable specific techniques.
As with IP addresses, MAC addresses uniquely identify devices on the
network; while they are not often available in traffic data collected
at Layer 3, and cannot be used to locate devices within the network,
some traces may contain sub-IP data including MAC address data.
Hardware addresses may be mappable to device serial numbers, and to
the entities or individuals who purchased the devices, when combined
with external databases. MAC addresses are also often used in
constructing IPv6 addresses (see section 2.5.1 of [RFC4291]), and as
such may be used to reconstruct the low-order bits of anonymized IPv6
addresses in certain circumstances. Therefore, MAC address
anonymization is also important.
Port numbers identify abstract entities (applications) as opposed to
real-world entities, but they can be used to classify hosts and user
behavior. Passive port fingerprinting, both of well-known and
ephemeral ports, can be used to determine the operating system
running on a host. Relative data volumes by port can also be used to
determine the host's function (workstation, web server, etc.); this
Boschi & Trammell Expires July 23, 2011 [Page 9]
Internet-Draft IP Flow Anonymization Support January 2011
information can be used to identify hosts and users.
While not identifiers in and of themselves, timestamps and counters
can reveal the behavior of the hosts and users on a network. Any
given network activity is recognizable by a pattern of relative time
differences and data volumes in the associated sequence of flows,
even without host address information. They can therefore be used to
identify hosts and users. Timestamps and counters are also
vulnerable to traffic injection attacks, where traffic with a known
pattern is injected into a network under measurement, and this
pattern is later identified in the anonymized data set.
The simplest and most extreme form of anonymization, which can be
applied to any field of a flow record, is black-marker anonymization,
or complete deletion of a given field. Note that black-marker
anonymization is equivalent to simply not exporting the field(s) in
question.
While black-marker anonymization completely protects the data in the
deleted fields from the risk of disclosure, it also reduces the
utility of the anonymized data set as a whole. Techniques that
retain some information while reducing (though not eliminating) the
disclosure risk will be extensively discussed in the following
sections; note that the techniques specifically applicable to IP
addresses, timestamps, ports, and counters will be discussed in
separate sections.
4.1. IP Address Anonymization
Since IP addresses are the most common identifiers within flow data
that can be used to directly identify a person, organization, or
host, most of the work on flow and trace data anonymization has gone
into IP address anonymization techniques. Indeed, the aim of most
attacks against anonymization is to recover the map from anonymized
IP addresses to original IP addresses thereby identifying the
identified hosts. There is therefore a wide range of IP address
anonymization schemes that fit into the following categories.
+------------------------------------+---------------------+
| Scheme | Action |
+------------------------------------+---------------------+
| Truncation | Generalization |
| Reverse Truncation | Generalization |
| Permutation | Direct Substitution |
| Prefix-preserving Pseudonymization | Direct Substitution |
+------------------------------------+---------------------+
Boschi & Trammell Expires July 23, 2011 [Page 10]
Internet-Draft IP Flow Anonymization Support January 2011
4.1.1. Truncation
Truncation removes "n" of the least significant bits from an IP
address, replacing them with zeroes. In effect, it replaces a host
address with a network address for some fixed netblock; for IPv4
addresses, 8-bit truncation corresponds to replacement with a /24
network address. Truncation is a non-reversible generalization
scheme. Note that while truncation is effective for making hosts
non-identifiable, it preserves information which can be used to
identify an organization, a geographic region, a country, or a
continent.
Truncation to an address length of 0 is equivalent to black-marker
anonymization. Complete removal of IP address information is only
recommended for analysis tasks which have no need to separate flow
data by host or network; e.g. as a first stage to per-application
(port) or time-series total volume analyses.
4.1.2. Reverse Truncation
Reverse truncation removes "n" of the most significant bits from an
IP address, replacing them with zeroes. Reverse truncation is a non-
reversible generalization scheme. Reverse truncation is effective
for making networks unidentifiable, partially or completely removing
information which can be used to identify an organization, a
geographic region, a country, or a continent (or RIR region of
responsibility). However, it may cause ambiguity when applied to
data collected from more than one network, since it treats all the
hosts with the same address on different networks as if they are the
same host. It is not particularly useful when publishing data where
the network of origin is known or can be easily guessed by virtue of
the identity of the publisher.
Like truncation, reverse truncation to an address length of 0 is
equivalent to black-marker anonymization.
4.1.3. Permutation
Permutation is a direct substitution technique, replacing each IP
address with an address selected from the set of possible IP
addresses, such that each anonymized address represents a unique
original address. The selection function is often random, though it
is not necessarily so. Permutation does not preserve any structural
information about a network, but it does preserve the unique count of
IP addresses. Any application that requires more structure than
host-uniqueness will not be able to use permuted IP addresses.
There are many variations of permutation functions, each of which has
Boschi & Trammell Expires July 23, 2011 [Page 11]
Internet-Draft IP Flow Anonymization Support January 2011
tradeoffs in performance, security, and guarantees of non-collision;
evaluating these tradeoffs is implementation independent. However,
in general permutation functions applied to anonymization SHOULD be
difficult to reverse without knowing the parameters (e.g., a secret
key for HMAC). Given the relatively small space of IPv4 addresses in
particular, hash functions applied without additional parameters
could be reversed through brute force if the hash function is known,
and SHOULD NOT be used as permutation functions. Permutation
functions may guarantee noncollision (i.e., that each anonymized
address represents a unique original address), but need not; however,
the probability of collision SHOULD be low. We treat even
permutations with low but nonzero collision probability as direct
substitution nevertheless. Beyond these guidelines, recommendations
for specific permutation functions are out of scope for this
document.
4.1.4. Prefix-preserving Pseudonymization
Prefix-preserving pseudonymization is a direct substitution
technique, like permutation but further restricted such that the
structure of subnets is preserved at each level while anonymising IP
addresses. If two real IP addresses match on a prefix of "n" bits,
the two anonymized IP addresses will match on a prefix of "n" bits as
well. This is useful when relationships among networks must be
preserved for a given analysis task, but introduces structure into
the anonymized data which can be exploited in attacks against the
anonymization technique.
Scanning in Internet background traffic can cause particular problems
with this technique: if a scanner uses a predictable and known
sequence of addresses, this information can be used to reverse the
substitution. The low order portion of the address can be left
unanonymized as a partial defense against this attack.
4.2. MAC Address Anonymization
Flow data containing sub-IP information can also contain identifying
information in the form of the hardware (MAC) address. While MAC
address information cannot be used to locate a node within a network,
it can be used to directly uniquely identify a specific device.
Vendors or organizations within the supply chain may then have the
information necessary to identify the entity or individual that
purchased the device.
MAC address information is not as structured as IP address
information. EUI-48 and EUI-64 MAC addresses contain an
Organizational Unique Identifier (OUI) in the three most significant
bytes of the address; this OUI additionally contains bits noting
Boschi & Trammell Expires July 23, 2011 [Page 12]
Internet-Draft IP Flow Anonymization Support January 2011
whether the address is locally or globally administered. Beyond
this, there is no standard relationship among the OUIs assigned to a
given vendor.
Note that MAC address information also appear within IPv6 addresses,
as the EAP-64 address, or EAP-48 address encoded as an EAP-64
address, is used as the least significant 64 bits of the IPv6 address
in the case of link local addressing or stateless autoconfiguration;
the considerations and techniques in this section may then apply to
such IPv6 addresses as well.
+-----------------------------+---------------------+
| Scheme | Action |
+-----------------------------+---------------------+
| Truncation | Generalization |
| Reverse Truncation | Generalization |
| Permutation | Direct Substitution |
| Structured Pseudonymization | Direct Substitution |
+-----------------------------+---------------------+
4.2.1. Truncation
Truncation removes "n" of the least significant bits from a MAC
address, replacing them with zeroes. In effect, it retains bits of
OUI, which identifies the manufacturer, while removing the least
significant bits identifying the particular device. Truncation of 24
bits of an EAP-48 or 40 bits of an EAP-64 address zeroes out the
device identifier while retaining the OUI.
Truncation is effective for making device manufacturers partially or
completely identifiable within a dataset while deleting unique host
identifiers; this can be used to retain and aggregate MAC layer
behavior by vendor.
Truncation to an address length of 0 is equivalent to black-marker
anonymization.
4.2.2. Reverse Truncation
Reverse truncation removes "n" of the most significant bits from a
MAC address, replacing them with zeroes. Reverse truncation is a
non-reversible generalization scheme. This has the effect of
removing bits of the OUI, which identify manufacturers, before
removing the least significant bits. Reverse truncation of 24 bits
zeroes out the OUI.
Reverse truncation is effective for making device manufacturers
partially or completely unidentifiable within a dataset. However, it
Boschi & Trammell Expires July 23, 2011 [Page 13]
Internet-Draft IP Flow Anonymization Support January 2011
may cause ambiguity by introducing the possibility of truncated MAC
address collision. Also note that the utility of removing
manufacturer information is not particularly well-covered by the
literature.
Reverse truncation to an address length of 0 is equivalent to black-
marker anonymization.
4.2.3. Permutation
Permutation is a direct substitution technique, replacing each MAC
address with an address selected from the set of possible MAC
addresses, such that each anonymized address represents a unique
original address. The selection function is often random, though it
is not necessarily so. Permutation does not preserve any structural
information about a network, but it does preserve the unique count of
devices on the network. Any application that requires more structure
than host-uniqueness will not be able to use permuted MAC addresses.
There are many variations of permutation functions, each of which has
tradeoffs in performance, security, and guarantees of non-collision;
evaluating these tradeoffs is implementation independent. However,
in general permutation functions applied to anonymization SHOULD be
difficult to reverse without knowing the parameters (e.g., a secret
key for HMAC). While the EAP-48 space is larger than the IPv4
address space, hash functions applied without additional parameters
could be reversed through brute force if the hash function is known,
and SHOULD NOT be used as permutation functions. Permutation
functions may guarantee noncollision (i.e., that each anonymized
address represents a unique original address), but need not; however,
the probability of collision SHOULD be low. We treat even
permutations with low but nonzero collision probability as direct
substitution nevertheless. Beyond these guidelines, recommendations
for specific permutation functions are out of scope for this
document.
4.2.4. Structured Pseudonymization
Structured pseudonymization for MAC addresses is a direct
substitution technique, like permutation, but restricted such that
the OUI (the most significant three bytes) is permuted separately
from the node identifier, the remainder. This is useful when the
uniqueness of OUIs must be preserved for a given analysis task, but
introduces structure into the anonymized data which can be exploited
in attacks against the anonymization technique.
Boschi & Trammell Expires July 23, 2011 [Page 14]
Internet-Draft IP Flow Anonymization Support January 2011
4.3. Timestamp Anonymization
The particular time at which a flow began or ended is not
particularly identifiable information, but it can be used as part of
attacks against other anonymization techniques or for user profiling,
e.g. as in [Mur07]. Timestamps can be used in traffic injection
attacks, which use known information about a set of traffic generated
or otherwise known by an attacker to recover mappings of other
anonymized fields, as well as to identify certain activity by
response delay and size fingerprinting, which compares response sizes
and inter-flow times in anonymized data to known values. Note that
these attacks have been shown to be relatively robust against
timestamp anonymization techniques (see [Bur10]), so the techniques
presented in this section are relatively weak and should be used with
care.
+-----------------------+----------------------------+
| Scheme | Action |
+-----------------------+----------------------------+
| Precision Degradation | Generalization |
| Enumeration | Direct or Set Substitution |
| Random Shifts | Direct Substitution |
+-----------------------+----------------------------+
4.3.1. Precision Degradation
Precision Degradation is a generalization technique that removes the
most precise components of a timestamp, accounting all events
occurring in each given interval (e.g. one millisecond for
millisecond level degradation) as simultaneous. This has the effect
of potentially collapsing many timestamps into one. With this
technique time precision is reduced, and sequencing may be lost, but
the information at which time the event occurred is preserved. The
anonymized data may not be generally useful for applications which
require strict sequencing of flows.
Note that flow meters with low time precision (e.g. second precision,
or millisecond precision on high-capacity networks) perform the
equivalent of precision degradation anonymization by their design.
Note also that degradation to a very low precision (e.g. on the order
of minutes, hours, or days) is commonly used in analyses operating on
time-series aggregated data, and may also be described as binning;
though the time scales are longer and applicability more restricted,
this is in principle the same operation.
Precision degradation to infinitely low precision is equivalent to
black-marker anonymization. Removal of timestamp information is only
Boschi & Trammell Expires July 23, 2011 [Page 15]
Internet-Draft IP Flow Anonymization Support January 2011
recommended for analysis tasks which have no need to separate flows
in time, for example for counting total volumes or unique occurrences
of other flow keys in an entire dataset.
4.3.2. Enumeration
Enumeration is a substitution function that retains the chronological
order in which events occurred while eliminating time information.
Timestamps are substituted by equidistant timestamps (or numbers)
starting from a randomly chosen start value. The resulting data is
useful for applications requiring strict sequencing, but not for
those requiring good timing information (e.g. delay- or jitter-
measurement for quality-of-service (QoS) applications or service-
level agreement (SLA) validation).
Note that enumeration is functionally equivalent to precision
degradation in any environment into which traffic can be regularly
injected to serve as a clock at the precision of the frequency of the
injected flows.
4.3.3. Random Shifts
Random time shifts add a random offset to every timestamp within a
dataset. This reversible substitution technique therefore retains
duration and inter-event interval information as well as
chronological order of flows. Random time shifts are quite weak, and
relatively easy to reverse in the presence of external knowledge
about traffic on the measured network.
4.4. Counter Anonymization
Counters (such as packet and octet volumes per flow) are subject to
fingerprinting and injection attacks against anonymization, or for
user profiling as timestamps are. Data sets with anonymized counters
are useful only for analysis tasks for which relative or imprecise
magnitudes of activity are useful. Counter information can also be
completely removed, but this is only recommended for analysis tasks
which have no need to evaluate the removed counter, for example for
counting only unique occurrences of other flow keys.
+-----------------------+----------------------------+
| Scheme | Action |
+-----------------------+----------------------------+
| Precision Degradation | Generalization |
| Binning | Generalization |
| Random noise addition | Direct or Set Substitution |
+-----------------------+----------------------------+
Boschi & Trammell Expires July 23, 2011 [Page 16]
Internet-Draft IP Flow Anonymization Support January 2011
4.4.1. Precision Degradation
As with precision degradation in timestamps, precision degradation of
counters removes lower-order bits of the counters, treating all the
counters in a given range as having the same value. Depending on the
precision reduction, this loses information about the relationships
between sizes of similarly-sized flows, but keeps relative magnitude
information. Precision degradation to an infinitely low precision is
equivalent to black-marker anonymization.
4.4.2. Binning
Binning can be seen as a special case of precision degradation; the
operation is identical, except for in precision degradation the
counter ranges are uniform, and in binning they need not be. For
example, consider separating unopened TCP connections from
potentially opened TCP connections. Here, packet counters per flow
would be binned into two bins, one for 1-2 packet flows, and one for
flows with 3 or more packets. Binning schemes are generally chosen
to keep precisely the amount of information required in a counter for
a given analysis task. Note that, also unlike precision degradation,
the bin label need not be within the bin's range. Binning counters
to a single bin is equivalent to black-marker anonymization.
4.4.3. Random Noise Addition
Random noise addition adds a random amount to a counter in each flow;
this is used to keep relative magnitude information and minimize the
disruption to size relationship information while avoiding
fingerprinting attacks against anonymization. Note that there is no
guarantee that random noise addition will maintain ranking order by a
counter among members of a set. Random noise addition is
particularly useful when the derived analysis data will not be
presented in such a way as to require the lower-order bits of the
counters.
4.5. Anonymization of Other Flow Fields
Other fields, particularly port numbers and protocol numbers, can be
used to partially identify the applications that generated the
traffic in a a given flow trace. This information can be used in
fingerprinting attacks, and may be of interest on its own (e.g., to
reveal that a certain application with suspected vulnerabilities is
running on a given network). These fields are generally anonymized
using one of two techniques.
Boschi & Trammell Expires July 23, 2011 [Page 17]
Internet-Draft IP Flow Anonymization Support January 2011
+-------------+---------------------+
| Scheme | Action |
+-------------+---------------------+
| Binning | Generalization |
| Permutation | Direct Substitution |
+-------------+---------------------+
4.5.1. Binning
Binning is a generalization technique mapping a set of potentially
non-uniform ranges into a set of arbitrarily labeled bins. Common
bin arrangements depend on the field type and the analysis
application. For example, an IP protocol bin arrangement may
preserve 1, 6, and 17 for ICMP, UDP, and TCP traffic, and bin all
other protocols into a single bin, to mitigate the use of uncommon
protocols in fingerprinting attacks. Another example arrangement may
bin source and destination ports into low (0-1023) and high (1024-
65535) bins in order to tell service from ephemeral ports without
identifying individual applications.
Binning other flow key fields to a single bin is equivalent to black-
marker anonymization. Removal of other flow key information is only
recommended for analysis tasks which have no need to differentiate
flows on the removed keys, for example for total traffic counts or
unique counts of other flow keys.
4.5.2. Permutation
Permutation is a direct substitution technique, replacing each value
with an value selected from the set of possible range, such that each
anonymized value represents a unique original value. This is used to
preserve the count of unique values without preserving information
about, or the ordering of, the values themselves.
While permutation ideally guarantees that each anonymized value
represents a unique original value, such may require significant
state in the Intermediate Anonymization Process. Therefore,
permutation may be implemented by hashing for performance reasons,
with hash functions that may have relatively small collision
probabilities. Such techniques are still essentially direct
substitution techniques, despite the nonzero error probability.
5. Parameters for the Description of Anonymization Techniques
This section details the abstract parameters used to describe the
anonymization techniques examined in the previous section, on a per-
parameter basis. These parameters and their export safety inform the
Boschi & Trammell Expires July 23, 2011 [Page 18]
Internet-Draft IP Flow Anonymization Support January 2011
design of the IPFIX anonymization metadata export specified in the
following section.
5.1. Stability
A stable anonymization will always map a given value in the real
space to a given value in the anonymized space, while an unstable
anonymization will change this mapping over time; a completely
unstable anonymization is essentially indistinguishable from black-
marker anonymization. Any given anonymization technique may be
applied with a varying range of stability. Stability is important
for assessing the comparability of anonymized information in
different data sets, or in the same data set over different time
periods. In practice, an anonymization may also be stable for every
data set published by an a particular producer to a particular
consumer, stable for a stated time period within a dataset or across
datasets, or stable only for a single data set.
If no information about stability is available, users of anonymized
data MAY assume that the techniques used are stable across the entire
dataset, but unstable across datasets. Note that stability presents
a risk-utility tradeoff, as completely stable anonymization can be
used for longer-term trend analysis tasks but also presents more risk
of attack given the stable mapping. Information about the stability
of a mapping SHOULD be exported along with the anonymized data.
5.2. Truncation Length
Truncation and precision degradation are described by the truncation
length, or the amount of data still remaining in the anonymized field
after anonymization.
Truncation length can generally be inferred from a given data set,
and need not be specially exported or protected. For bit-level
truncation, the truncated bits are generally inferable by the least
significant bit set for an instance of an Information Element
described by a given Template (or the most significant bit set, in
the case of reverse truncation). For precision degradation, the
truncation is inferable from the maximum precision given. Note that
while this inference method is generally applicable, it is data-
dependent: there is no guarantee that it will recover the exact
truncation length used to prepare the data.
In the special case of IP address export with variable (per-record)
truncation, the truncation MAY be expressed by exporting the prefix
length alongside the address.
Boschi & Trammell Expires July 23, 2011 [Page 19]
Internet-Draft IP Flow Anonymization Support January 2011
5.3. Bin Map
Binning is described by the specification of a bin mapping function.
This function can be generally expressed in terms of an associative
array that maps each point in the original space to a bin, although
from an implementation standpoint most bin functions are much simpler
and more efficient.
Since the bin map for a bin mapping function is in essence the bin
mapping key, and can be used to partially deanonymize binned data,
depending on the degree of generalization, information about the bin
mapping function SHOULD NOT be exported.
5.4. Permutation
Like binning, permutation is described by the specification of a
permutation function. In the general case, this can be expressed in
terms of an associative array that maps each point in the original
space to a point in the anonymized space. Unlike binning, each point
in the anonymized space corresponds to a single, unique point in the
original space.
Since the parameters of the permutation function are in essence key-
like (indeed, for cryptographic permutation functions, they are the
keys themselves), information about the permutation function or its
parameters SHOULD NOT be exported.
5.5. Shift Amount
Shifting requires an amount to shift each value by. Since the shift
amount is the only key to a shift function, and can be used to
trivially deanonymize data protected by shifting, information about
the shift amount SHOULD NOT be exported.
6. Anonymization Export Support in IPFIX
Anonymized data exported via IPFIX SHOULD be annotated with
anonymization metadata, which details which fields described by which
Templates are anonymized, and provides appropriate information on the
anonymization techniques used. This metadata SHOULD be exported in
Data Records described by the recommended Options Templates described
in this section; these Options Templates use the additional
Information Elements described in the following subsection.
Note that fields anonymized using the black-marker (removal)
technique do not require any special metadata support: black-marker
anonymized fields SHOULD NOT be exported at all, by omitting the
Boschi & Trammell Expires July 23, 2011 [Page 20]
Internet-Draft IP Flow Anonymization Support January 2011
corresponding Information Elements from Template describing the Data
Set. In the case where application requirements dictate that a black-
marker anonymized field must remain in a Template, then an Exporting
Process MAY export black-marker anonymized fields with their native
length as all-zeros, but only in cases where enough contextual
information exists within the record to differentiate a black-marker
anonymized field exported in this way from a real zero value.
6.1. Anonymization Records and the Anonymization Options Template
The Anonymization Options Template describes Anonymization Records,
which allow anonymization metadata to be exported inline over IPFIX
or stored in an IPFIX File, by binding information about
anonymization techniques to Information Elements within defined
Templates or Options Templates. IPFIX Exporting Processes SHOULD
export anonymization records for any Template describing exported
anonymized Data Records; IPFIX Collecting Processes and processes
downstream from them MAY use anonymization records to treat
anonymized data differently depending on the applied technique.
Anonymization Records contain ancillary information bound to a
Template, so many of the considerations for Templates apply to
Anonymization Records as well. First, reliability is important: an
Exporting Process SHOULD export Anonymization Records after the
Templates they describe have been exported, and SHOULD export
anonymization records reliably if supported by the underlying
transport (i.e., without partial reliability when using SCTP)
Anonymization Records MUST be handled by Collecting Processes as
scoped to the Template to which they apply within the Transport
Session in which they are sent. When a Template is withdrawn via a
Template Withdrawal Message or expires during a UDP transport
session, the accompanying Anonymization Records are withdrawn or
expire as well, and do not apply to subsequent Templates with the
same Template ID within the Session unless re-exported.
The Stability Class within the anonymizationFlags IE can be used to
declare that a given anonymization technique's mapping will remain
stable across multiple sessions, but this does not mean that
anonymization technique information given in the Anonymization
Records themselves persist across Sessions. Each new Transport
Session MUST contain new Anonymization Records for each Template
describing anonymized Data Sets.
SCTP per-stream export [I-D.ietf-ipfix-export-per-sctp-stream] may be
used to ease management of Anonymization Records if appropriate for
the application.
Boschi & Trammell Expires July 23, 2011 [Page 21]
Internet-Draft IP Flow Anonymization Support January 2011
The fields of the Anonymization Options template are as follows:
+-------------------------+-----------------------------------------+
| IE | Description |
+-------------------------+-----------------------------------------+
| templateId [scope] | The Template ID of the Template or |
| | Options Template containing the |
| | Information Element described by this |
| | anonymization record. This Information |
| | Element MUST be defined as a Scope |
| | Field. |
| informationElementId | The Information Element identifier of |
| [scope] | the Information Element described by |
| | this anonymization record. This |
| | Information Element MUST be defined as |
| | a Scope Field. Exporting Processes |
| | MUST clear then Enterprise bit of the |
| | informationElementId and Collecting |
| | Processes SHOULD ignore it; information |
| | about enterprise-specific Information |
| | Elements is exported via the |
| | privateEnterpriseNumber Information |
| | Element. |
| privateEnterpriseNumber | The Private Enterprise Number of the |
| [scope] [optional] | enterprise-specific Information Element |
| | described by this anonymization record. |
| | This Information Element MUST be |
| | defined as a Scope Field if present. A |
| | privateEnterpriseNumber of 0 signifies |
| | that the Information Element is |
| | IANA-registered. |
| informationElementIndex | The Information Element index of the |
| [scope] [optional] | instance of the Information Element |
| | described by this anonymization record |
| | identified by the informationElementId |
| | within the Template. Optional; need |
| | only be present when describing |
| | Templates that have multiple instances |
| | of the same Information Element. This |
| | Information Element MUST be defined as |
| | a Scope Field if present. This |
| | Information Element is defined in |
| | Section 6.2, below. |
| anonymizationFlags | Flags describing the mapping stability |
| | and specialized modifications to the |
| | Anonymization Technique in use. SHOULD |
| | be present. This Information Element |
| | is defined in Section 6.2.3, below. |
Boschi & Trammell Expires July 23, 2011 [Page 22]
Internet-Draft IP Flow Anonymization Support January 2011
| anonymizationTechnique | The technique used to anonymize the |
| | data. MUST be present. This |
| | Information Element is defined in |
| | Section 6.2.2, below. |
+-------------------------+-----------------------------------------+
6.2. Recommended Information Elements for Anonymization Metadata
6.2.1. informationElementIndex
Description: A zero-based index of an Information Element
referenced by informationElementId within a Template referenced by
templateId; used to disambiguate scope for templates containing
multiple identical Information Elements.
Abstract Data Type: unsigned16
Data Type Semantics: identifier
ElementId: TBD3
Status: Current
6.2.2. anonymizationTechnique
Description: A description of the anonymization technique applied
to a referenced Information Element within a referenced Template.
Each technique may be applicable only to certain Information
Elements and recommended only for certain Infomation Elements;
these restrictions are noted in the table below.
+-------+---------------------------+-----------------+-------------+
| Value | Description | Applicable to | Recommended |
| | | | for |
+-------+---------------------------+-----------------+-------------+
| 0 | Undefined: the Exporting | all | all |
| | Process makes no | | |
| | representation as to | | |
| | whether the defined field | | |
| | is anonymized or not. | | |
| | While the Collecting | | |
| | Process MAY assume that | | |
| | the field is not | | |
| | anonymized, it is not | | |
| | guaranteed not to be. | | |
| | This is the default | | |
| | anonymization technique. | | |
Boschi & Trammell Expires July 23, 2011 [Page 23]
Internet-Draft IP Flow Anonymization Support January 2011
| 1 | None: the values exported | all | all |
| | are real. | | |
| 2 | Precision | all | all |
| | Degradation/Truncation: | | |
| | the values exported are | | |
| | anonymized using simple | | |
| | precision degradation or | | |
| | truncation. The new | | |
| | precision or number of | | |
| | truncated bits is | | |
| | implicit in the exported | | |
| | data, and can be deduced | | |
| | by the Collecting | | |
| | Process. | | |
| 3 | Binning: the values | all | all |
| | exported are anonymized | | |
| | into bins. | | |
| 4 | Enumeration: the values | all | timestamps |
| | exported are anonymized | | |
| | by enumeration. | | |
| 5 | Permutation: the values | all | identifiers |
| | exported are anonymized | | |
| | by permutation. | | |
| 6 | Structured Permutation: | addresses | |
| | the values exported are | | |
| | anonymized by | | |
| | permutation, preserving | | |
| | bit-level structure as | | |
| | appropriate; this | | |
| | represents | | |
| | prefix-preserving IP | | |
| | address anonymization or | | |
| | structured MAC address | | |
| | anonymization. | | |
| 7 | Reverse Truncation: the | addresses | |
| | values exported are | | |
| | anonymized using reverse | | |
| | truncation. The number | | |
| | of truncated bits is | | |
| | implicit in the exported | | |
| | data, and can be deduced | | |
| | by the Collecting | | |
| | Process. | | |
| 8 | Noise: the values | non-identifiers | counters |
| | exported are anonymized | | |
| | by adding random noise to | | |
| | each value. | | |
Boschi & Trammell Expires July 23, 2011 [Page 24]
Internet-Draft IP Flow Anonymization Support January 2011
| 9 | Offset: the values | all | timestamps |
| | exported are anonymized | | |
| | by adding a single offset | | |
| | to all values. | | |
+-------+---------------------------+-----------------+-------------+
Abstract Data Type: unsigned16
Data Type Semantics: identifier
ElementId: TBD2
Status: Current
6.2.3. anonymizationFlags
Description: A flag word describing specialized modifications to
the anonymization policy in effect for the anonymization technique
applied to a referenced Information Element within a referenced
Template. When flags are clear (0), the normal policy (as
described by anonymizationTechnique) applies without modification.
MSB 14 13 12 11 10 9 8 7 6 5 4 3 2 1 LSB
+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+
| Reserved |LOR|PmA| SC |
+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+
anonymizationFlags IE
+--------+----------+-----------------------------------------------+
| bit(s) | name | description |
| (LSB = | | |
| 0) | | |
+--------+----------+-----------------------------------------------+
| 0-1 | SC | Stability Class: see the Stability Class |
| | | table below, and section Section 5.1. |
Boschi & Trammell Expires July 23, 2011 [Page 25]
Internet-Draft IP Flow Anonymization Support January 2011
| 2 | PmA | Perimeter Anonymization: when set (1), |
| | | source- Information Elements as described in |
| | | [RFC5103] are interpreted as external |
| | | addresses, and destination- Information |
| | | Elements as described in [RFC5103] are |
| | | interpreted as internal addresses, for the |
| | | purposes of associating |
| | | anonymizationTechnique to Information |
| | | Elements only; see Section 7.2.2 for details. |
| | | This bit MUST NOT be set when associated with |
| | | a non-endpoint (i.e., source- or |
| | | destination-) Information Element. SHOULD be |
| | | consistent within a record (i.e., if a |
| | | source- Information Element has this flag |
| | | set, the corresponding destination- element |
| | | SHOULD have this flag set, and vice-versa.) |
| 3 | LOR | Low-Order Unchanged: when set (1), the |
| | | low-order bits of the anonymized Information |
| | | Element contain real data. This modification |
| | | is intended for the anonymization of |
| | | network-level addresses while leaving |
| | | host-level addresses intact in order to |
| | | preserve host level-structure, which could |
| | | otherwise be used to reverse anonymization. |
| | | MUST NOT be set when associated with a |
| | | truncation-based anonymizationTechnique. |
| 4-15 | Reserved | Reserved for future use: SHOULD be cleared |
| | | (0) by the Exporting Process and MUST be |
| | | ignored by the Collecting Process. |
+--------+----------+-----------------------------------------------+
The Stability Class portion of this flags word describes the
stability class of the anonymization technique applied to a
referenced Information Element within a referenced Template.
Stability classes refer to the stability of the parameters of the
anonymization technique, and therefore the comparability of the
mapping between the real and anonymized values over time. This
determines which anonymized datasets may be compared with each
other. Values are as follows:
Boschi & Trammell Expires July 23, 2011 [Page 26]
Internet-Draft IP Flow Anonymization Support January 2011
+-----+-----+-------------------------------------------------------+
| Bit | Bit | Description |
| 1 | 0 | |
+-----+-----+-------------------------------------------------------+
| 0 | 0 | Undefined: the Exporting Process makes no |
| | | representation as to how stable the mapping is, or |
| | | over what time period values of this field will |
| | | remain comparable; while the Collecting Process MAY |
| | | assume Session level stability, Session level |
| | | stability is not guaranteed. Processes SHOULD assume |
| | | this is the case in the absence of stability class |
| | | information; this is the default stability class. |
| 0 | 1 | Session: the Exporting Process will ensure that the |
| | | parameters of the anonymization technique are stable |
| | | during the Transport Session. All the values of the |
| | | described Information Element for each Record |
| | | described by the referenced Template within the |
| | | Transport Session are comparable. The Exporting |
| | | Process SHOULD endeavour to ensure at least this |
| | | stability class. |
| 1 | 0 | Exporter-Collector Pair: the Exporting Process will |
| | | ensure that the parameters of the anonymization |
| | | technique are stable across Transport Sessions over |
| | | time with the given Collecting Process, but may use |
| | | different parameters for different Collecting |
| | | Processes. Data exported to different Collecting |
| | | Processes are not comparable. |
| 1 | 1 | Stable: the Exporting Process will ensure that the |
| | | parameters of the anonymization technique are stable |
| | | across Transport Sessions over time, regardless of |
| | | the Collecting Process to which it is sent. |
+-----+-----+-------------------------------------------------------+
Abstract Data Type: unsigned16
Data Type Semantics: flags
ElementId: TBD1
Status: Current
7. Applying Anonymization Techniques to IPFIX Export and Storage
When exporting or storing anonymized flow data using IPFIX, certain
interactions between the IPFIX Protocol and the anonymization
techniques in use must be considered; these are treated in the
subsections below.
Boschi & Trammell Expires July 23, 2011 [Page 27]
Internet-Draft IP Flow Anonymization Support January 2011
7.1. Arrangement of Processes in IPFIX Anonymization
Anonymization may be applied to IPFIX data at three stages within the
collection infrastructure: on initial export, at a mediator, or after
collection, as shown in Figure 1. Each of these locations has
specific considerations and applicability.
+==========================================+
| Exporting Process |
+==========================================+
| |
| (Anonymized at Original Exporter) |
V |
+=============================+ |
| Mediator | |
+=============================+ |
| |
| (Anonymising Mediator) |
V V
+==========================================+
| Collecting Process |
+==========================================+
|
| (Anonymising CP/File Writer)
V
+--------------------+
| IPFIX File Storage |
+--------------------+
Figure 1: Potential Anonymization Locations
Anonymization is generally performed before the wider dissemination
or repurposing of a flow data set, e.g., adapting operational
measurement data for research. Therefore, direct anonymization of
flow data on initial export is only applicable in certain restricted
circumstances: when the Exporting Process (EP) is "publishing" data
to a Collecting Process (CP) directly, and the Exporting Process and
Collecting Process are operated by different entities. Note that
certain guidelines in Section 7.2.3 with respect to timestamp
anonymization may not apply in this case, as the Collecting Process
may be able to deduce certain timing information from the time at
which each Message is received.
A much more flexible arrangement is to anonymize data within a
Mediator [I-D.ietf-ipfix-mediators-framework]. Here, original data
is sent to a Mediator, which performs the anonymization function and
re-exports the anonymized data. Such a Mediator could be located at
the administrative domain boundary of the initial Exporting Process
Boschi & Trammell Expires July 23, 2011 [Page 28]
Internet-Draft IP Flow Anonymization Support January 2011
operator, exporting anonymized data to other consumers outside the
organization. In this case, the original Exporter SHOULD use TLS
[RFC5246] as specified in [RFC5101] to secure the channel to the
Mediator, and the Mediator should follow the guidelines in
Section 7.2, to mitigate the risk of original data disclosure.
When data is to be published as an anonymized data set in an IPFIX
File [RFC5655], the anonymization may be done at the final Collecting
Process before storage and dissemination, as well. In this case, the
Collector should follow the guidelines in Section 7.2, especially as
regards File-specific Options in Section 7.2.4
In each of these data flows, the anonymization of records is
undertaken by an Intermediate Anonymization Process (IAP); the data
flows into and out of this IAP are shown in Figure 2 below.
packets --+ +- IPFIX Messages -+
| | |
V V V
+==================+ +====================+ +=============+
| Metering Process | | Collecting Process | | File Reader |
+==================+ +====================+ +=============+
| Non-anonymized | Records |
V V V
+=========================================================+
| Intermediate Anonymization Process (IAP) |
+=========================================================+
| Anonymized ^ Anonymized |
| Records | Records |
V | V
+===================+ Anonymization +=============+
| Exporting Process |<--- Parameters ------>| File Writer |
+===================+ +=============+
| |
+------------> IPFIX Messages <----------+
Figure 2: Data flows through the anonymization process
Anonymization parameters must also be available to the Exporting
Process and/or File Writer in order to ensure header data is also
appropriately anonymized as in Section 7.2.3.
Following each of the data flows through the IAP, we describe five
basic types of anonymization arrangements within this framework in
Figure 3. In addition to the three arrangements described in detail
above, anonymization can also be done at a collocated Metering
Process (MP) and File Writer (FW) (see section 7.3.2 of [RFC5655]),
or at a file manipulator, which combines a File Writer with a File
Boschi & Trammell Expires July 23, 2011 [Page 29]
Internet-Draft IP Flow Anonymization Support January 2011
Reader (FR) (see section 7.3.7 of [RFC5655]).
+----+ +-----+ +----+
pkts -> | MP |->| IAP |->| EP |-> anonymization on Original Exporter
+----+ +-----+ +----+
+----+ +-----+ +----+
pkts -> | MP |->| IAP |->| FW |-> Anonymising collocated MP/File Writer
+----+ +-----+ +----+
+----+ +-----+ +----+
IPFIX -> | CP |->| IAP |->| EP |-> Anonymising Mediator (Masq. Proxy)
+----+ +-----+ +----+
+----+ +-----+ +----+
IPFIX -> | CP |->| IAP |->| FW |-> Anonymising collocated CP/File Writer
+----+ +-----+ +----+
+----+ +-----+ +----+
IPFIX -> | FR |->| IAP |->| FW |-> Anonymising file manipulator
File +----+ +-----+ +----+
Figure 3: Possible anonymization arrangements in the IPFIX
architecture
Note that anonymization may occur at more than one location within a
given collection infrastructure, to provide varying levels of
anonymization, disclosure risk, or data utility for specific
purposes.
7.2. IPFIX-Specific Anonymization Guidelines
In implementing and deploying the anonymization techniques described
in this document, implementors should note that IPFIX already
provides features that support anonymized data export, and use these
where appropriate. Care must also be taken that data structures
supporting the operation of the protocol itself do not leak data that
could be used to reverse the anonymization applied to the flow data.
Such data structures may appear in the header, or within the data
stream itself, especially as options data. Each of these and their
impact on specific anonymization techniques is noted in a separate
subsection below.
7.2.1. Appropriate Use of Information Elements for Anonymized Data
Note, as in Section 6 above, that black-marker anonymized fields
SHOULD NOT be exported at all; the absence of the field in a given
Data Set is implicitly declared by not including the corresponding
Information Element in the Template describing that Data Set.
When using precision degradation of timestamps, Exporting Processes
SHOULD export timing information using Information Elements of an
Boschi & Trammell Expires July 23, 2011 [Page 30]
Internet-Draft IP Flow Anonymization Support January 2011
appropriate precision, as explained in Section 4.5 of [RFC5153]. For
example, timestamps measured in millisecond-level precision and
degraded to second-level precision should use flowStartSeconds and
flowEndSeconds, not flowStartMilliseconds and flowEndMilliseconds.
When exporting anonymized data and anonymization metadata, Exporting
Processes SHOULD ensure that the combination of Information Element
and declared anonymization technique are compatible. Specifically,
the applicable and recommended Information Element types and
semantics for each technique are noted in the description of the
anonymizationTechnique Information Element in Section 6.2.2. In this
description, a timestamp is an Information Element with the data type
dateTimeSeconds, dataTimeMilliseconds, dateTimeMicroseconds, or
dateTimeNanoseconds; an address is an Information Element with the
data type ipv4Address, ipv6Address, or macAddress; and an identifier
is an Information Element with identifier data type semantics.
Exporting Process MUST NOT export Anonymization Options records
binding techniques to Information Elements to which they are not
applicable, and SHOULD NOT export Anonymization Options records
binding techniques to Information Elements for which they are not
recommended.
7.2.2. Export of Perimeter-Based Anonymization Policies
Data collected from a single network may require different
anonymization policies for addresses internal and external to the
network. For example, internal addresses could be subject to simple
permutation, while external addresses could be aggregated into
networks by truncation. When exporting anonymized perimeter
bidirectional flow (biflow) data as in section 5.2 of [RFC5103], this
arrangement may be easily represented by specifying one technique for
source endpoint information (which represents the external endpoint
in a perimeter biflow) and one technique for destination endpoint
information (which represents the internal address in a perimeter
biflow).
However, it can also be useful to represent perimeter-based
anonymization policies with unidirectional flow (uniflow), or non-
perimeter biflow data. In this case, the Perimeter Anonymization bit
(bit 2) in the anonymizationFlags Information Element describing the
anonymized address Information Elements can be set to change the
meaning of "source" and "destination" of Information Elements to mean
"external" and "internal" as with perimeter biflows, but only with
respect to anonymization policies.
Boschi & Trammell Expires July 23, 2011 [Page 31]
Internet-Draft IP Flow Anonymization Support January 2011
7.2.3. Anonymization of Header Data
Each IPFIX Message contains a Message Header; within this Message
Header are contained two fields which may be used to break certain
anonymization techniques: the Export Time, and the Observation Domain
ID
Export of IPFIX Messages containing anonymized timestamp data where
the original Export Time Message header has some relationship to the
anonymized timestamps SHOULD anonymize the Export Time header field
so that the Export Time is consistent with the anonymized timestamp
data. Otherwise, relationships between export and flow time could be
used to partially or totally reverse timestamp anonymization. When
anonymising timestamps and the Export Time header field SHOULD avoid
times too far in the past or future; while [RFC5101] does not make
any allowance for Export Time error detection, it is sensible that
Collecting Processes may interpret Messages with seemingly
nonsensical Export Times as erroneous. Specific limits are
implementation-dependent, but this issue may cause interoperability
issues when anonymising the Export Time header field.
The similarity in size between an Observation Domain ID and an IPv4
address (32 bits) may lead to a temptation to use an IPv4 interface
address on the Metering or Exporting Process as the Observation
Domain ID. If this address bears some relation to the IP addresses
in the flow data (e.g., shares a network prefix with internal
addresses) and the IP addresses in the flow data are anonymized in a
structure-preserving way, then the Observation Domain ID may be used
to break the IP address anonymization. Use of an IPv4 interface
address on the Metering or Exporting Process as the Observation
Domain ID is NOT RECOMMENDED in this case.
7.2.4. Anonymization of Options Data
IPFIX uses the Options mechanism to export, among other things,
metadata about exported flows and the flow collection infrastructure.
As with the IPFIX Message Header, certain Options recommended in
[RFC5101] and [RFC5655] containing flow timestamps and network
addresses of Exporting and Collecting Processes may be used to break
certain anonymization techniques. When using these Options along
anonymized data export and storage, values within the Options which
could be used to break the anonymization SHOULD themselves be
anonymized or omitted.
The Exporting Process Reliability Statistics Options Template,
recommended in [RFC5101], contains an Exporting Process ID field,
which may be an exportingProcessIPv4Address Information Element or an
exportingProcessIPv6Address Information Element. If the Exporting
Boschi & Trammell Expires July 23, 2011 [Page 32]
Internet-Draft IP Flow Anonymization Support January 2011
Process address bears some relation to the IP addresses in the flow
data (e.g., shares a network prefix with internal addresses) and the
IP addresses in the flow data are anonymized in a structure-
preserving way, then the Exporting Process address may be used to
break the IP address anonymization. Exporting Processes exporting
anonymized data in this situation SHOULD mitigate the risk of attack
either by omitting Options described by the Exporting Process
Reliability Statistics Options Template, or by anonymising the
Exporting Process address using a similar technique to that used to
anonymize the IP addresses in the exported data.
Similarly, the Export Session Details Options Template and Message
Details Options Template specified for the IPFIX File Format
[RFC5655] may contain the exportingProcessIPv4Address Information
Element or the exportingProcessIPv6Address Information Element to
identify an Exporting Process from which a flow record was received,
and the collectingProcessIPv4Address Information Element or the
collectingProcessIPv6Address Information Element to identify the
Collecting Process which received it. If the Exporting Process or
Collecting Process address bears some relation to the IP addresses in
the data set (e.g., shares a network prefix with internal addresses)
and the IP addresses in the data set are anonymized in a structure-
preserving way, then the Exporting Process or Collecting Process
address may be used to break the IP address anonymization. Since
these Options Templates are primarily intended for storing IPFIX
Transport Session data for auditing, replay, and testing purposes, it
is NOT RECOMMENDED that storage of anonymized data include these
Options Templates in order to mitigate the risk of attack.
The Message Details Options Template specified for the IPFIX File
Format [RFC5655] also contains the collectionTimeMilliseconds
Information Element. As with the Export Time Message Header field,
if the exported data set contains anonymized timestamp information,
and the collectionTimeMilliseconds Information Element in a given
Message has some relationship to the anonymized timestamp
information, then this relationship can be exploited to reverse the
timestamp anonymization. Since this Options Template is primarily
intended for storing IPFIX Transport Session data for auditing,
replay, and testing purposes, it is NOT RECOMMENDED that storage of
anonymized data include this Options Template in order to mitigate
the risk of attack.
Since the Time Window Options Template specified for the IPFIX File
Format [RFC5655] refers to the timestamps within the data set to
provide partial table of contents information for an IPFIX File,
Options described by this template SHOULD be written using the
anonymized timestamps instead of the original ones.
Boschi & Trammell Expires July 23, 2011 [Page 33]
Internet-Draft IP Flow Anonymization Support January 2011
7.2.5. Special-Use Address Space Considerations
When anonymising data for transport or storage using IPFIX containing
anonymized IP addresses, and the analysis purpose permits doing so,
it is RECOMMENDED to filter out or leave unanonymized data containing
the special-use IPv4 addresses enumerated in [RFC5735] or the
special-use IPv6 addresses enumerated in [RFC5156]. Data containing
these addresses (e.g. 0.0.0.0 and 169.254.0.0/16 for link-local
autoconfiguration in IPv4 space) are often associated with specific,
well-known behavioral patterns. Detection of these patterns in
anonymized data can lead to deanonymization of these special-use
addresses, which increases the chance of a complete reversal of
anonymization by an attacker, especially of prefix-preserving
techniques.
7.2.6. Protecting Out-of-Band Configuration and Management Data
Special care should be taken when exporting or sharing anonymized
data to avoid information leakage via the configuration or management
planes of the IPFIX Device containing the Exporting Process or the
File Writer. For example, adding noise to counters is useless if the
receiver can deduce the values in the counters from SNMP information,
and concealing the network under test is similarly useless if such
information is available in a configuration document. As the
specifics of these concerns are largely implementation- and
deployment-dependent, specific mitigation is out of scope for this
draft. The general ground rule is that information of similar type
to that anonymized SHOULD NOT be made available to the receiver by
any means, whether in the Data Records, in IPFIX protocol structures
such as Message Headers, or out-of-band.
8. Examples
In this example, consider the export or storage of an anonymized IPv4
data set from a single network described by a simple template
containing a timestamp in seconds, a five-tuple, and packet and octet
counters. The template describing each record in this data set is
shown in figure Figure 4.
Boschi & Trammell Expires July 23, 2011 [Page 34]
Internet-Draft IP Flow Anonymization Support January 2011
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 2 | Length = 40 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID = 256 | Field Count = 8 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| flowStartSeconds 150 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| sourceIPv4Address 8 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| destinationIPv4Address 12 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| sourceTransportPort 7 | Field Length = 2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| destinationTransportPort 11 | Field Length = 2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| packetDeltaCount 2 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| octetDeltaCount 1 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| protocolIdentifier 4 | Field Length = 1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 4: Example Flow Template
Suppose that this data set is anonymized according to the following
policy:
o IP addresses within the network are protected by reverse
truncation.
o IP addresses outside the network are protected by prefix-
preserving anonymization.
o Octet counts are exported using degraded precision in order to
provide minimal protection against fingerprinting attacks.
o All other fields are exported unanonymized.
In order to export anonymization records for this template and
policy, first, the Anonymization Options Template shown in figure
Figure 5 is exported. For this example, the optional
privateEnterpriseNumber and informationElementIndex Information
Elements are omitted, because they are not used.
Boschi & Trammell Expires July 23, 2011 [Page 35]
Internet-Draft IP Flow Anonymization Support January 2011
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 3 | Length = 26 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID = 257 | Field Count = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope Field Count = 2 |0| templateID 145 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Field Length = 2 |0| informationElementId 303 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Field Length = 2 |0| anonymizationFlags TBD1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Field Length = 2 |0| anonymizationTechnique TBD2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Field Length = 2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 5: Example Anonymization Options Template
Following the Anonymization Options Template comes a Data Set
containing Anonymization Records. This data set has an entry for
each Information Element Specifier in Template 256 describing the
flow records. This Data Set is shown in figure Figure 6. Note that
sourceIPv4Address and destinationIPv4Address have the Perimeter
Anonymization (0x0004) flag set in anonymizationFlags, meaning that
source address should be treated as network-external, and the
destination address as network-internal.
Boschi & Trammell Expires July 23, 2011 [Page 36]
Internet-Draft IP Flow Anonymization Support January 2011
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 257 | Length = 68 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template 256 | flowStartSeconds IE 150 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| no flags 0x0000 | Not Anonymized 1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template 256 | sourceIPv4Address IE 8 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Perimeter, Session SC 0x0005 | Structured Permutation 6 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template 256 | destinationIPv4Address IE 12 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Perimeter, Stable 0x0007 | Reverse Truncation 7 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template 256 | sourceTransportPort IE 7 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| no flags 0x0000 | Not Anonymized 1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template 256 | dest.TransportPort IE 11 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| no flags 0x0000 | Not Anonymized 1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template 256 | packetDeltaCount IE 2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| no flags 0x0000 | Not Anonymized 1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template 256 | octetDeltaCount IE 1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Stable 0x0003 | Precision Degradation 2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template 256 | protocolIdentifier IE 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| no flags 0x0000 | Not Anonymized 1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 6: Example Anonymization Records
Following the Anonymization Records come the data sets containing the
anonymized data, exported according to the template in figure
Figure 4. Bringing it all together, consider an IPFIX Message
containing three real data records and the necessary templates to
export them, shown in Figure 7. (Note that the scale of this message
is 8-bytes per line, for compactness; lines of dots '. . . . . '
represent shifting of the example bit structure for clarity.)
Boschi & Trammell Expires July 23, 2011 [Page 37]
Internet-Draft IP Flow Anonymization Support January 2011
1 2 3 4 5 6
0 2 4 6 8 0 2 4 6 8 0 2 4 6 8 0 2 4 6 8 0 2 4 6 8 0 2 4 6 8 0 2
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x000a | length 135 | export time 1271227717 | msg
| sequence 0 | domain 1 | hdr
| SetID 2 | length 40 | tid 256 | fields 8 | tmpl
| IE 150 | length 4 | IE 8 | length 4 | set
| IE 12 | length 4 | IE 7 | length 2 |
| IE 11 | length 2 | IE 2 | length 4 |
| IE 1 | length 4 | IE 4 | length 1 |
| SetID 256 | length 79 | time 1271227681 | data
| sip 192.0.2.3 | dip 198.51.100.7 | set
| sp 53 | dp 53 | packets 1 |
| bytes 74 | prt 17 | . . . . . . . . . . .
| time 1271227682 | sip 198.51.100.7 |
| dip 192.0.2.88 | sp 5091 | dp 80 |
| packets 60 | bytes 2896 |
| prt 6 | . . . . . . . . . . . . . . . . . . . . . . . . . . .
| time 1271227683 | sip 198.51.100.7 |
| dip 203.0.113.9 | sp 5092 | dp 80 |
| packets 44 | bytes 2037 |
| prt 6 |
+---------+
Figure 7: Example Real Message
The corresponding anonymized message is then shown in Figure 8. The
options template set describing Anonymization Records and the
Anonymization Records themselves are added; IP addresses and byte
counts are anonymized as declared.
Boschi & Trammell Expires July 23, 2011 [Page 38]
Internet-Draft IP Flow Anonymization Support January 2011
1 2 3 4 5 6
0 2 4 6 8 0 2 4 6 8 0 2 4 6 8 0 2 4 6 8 0 2 4 6 8 0 2 4 6 8 0 2
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x000a | length 233 | export time 1271227717 | msg
| sequence 0 | domain 1 | hdr
| SetID 2 | length 40 | tid 256 | fields 8 | tmpl
| IE 150 | length 4 | IE 8 | length 4 | set
| IE 12 | length 4 | IE 7 | length 2 |
| IE 11 | length 2 | IE 2 | length 4 |
| IE 1 | length 4 | IE 4 | length 1 |
| SetID 3 | length 30 | tid 257 | fields 4 | opt
| scope 2 | . . . . . . . . . . . . . . . . . . . . . . . . tmpl
| IE 145 | length 2 | IE 303 | length 2 | set
| IE TBD1 | length 2 | IE TBD2 | length 2 |
| SetID 257 | length 68 | . . . . . . . . . . . . . . . . anon
| tid 256 | IE 150 | flags 0 | tech 1 | recs
| tid 256 | IE 8 | flags 5 | tech 6 |
| tid 256 | IE 12 | flags 7 | tech 7 |
| tid 256 | IE 7 | flags 0 | tech 1 |
| tid 256 | IE 11 | flags 0 | tech 1 |
| tid 256 | IE 2 | flags 0 | tech 1 |
| tid 256 | IE 1 | flags 3 | tech 2 |
| tid 256 | IE41 | flags 0 | tech 1 |
| SetID 256 | length 79 | time 1271227681 | data
| sip 254.202.119.209 | dip 0.0.0.7 | set
| sp 53 | dp 53 | packets 1 |
| bytes 100 | prt 17 | . . . . . . . . . . .
| time 1271227682 | sip 0.0.0.7 |
| dip 254.202.119.6 | sp 5091 | dp 80 |
| packets 60 | bytes 2900 |
| prt 6 | . . . . . . . . . . . . . . . . . . . . . . . . . . .
| time 1271227683 | sip 0.0.0.7 |
| dip 2.19.199.176 | sp 5092 | dp 80 |
| packets 60 | bytes 2000 |
| prt 6 |
+---------+
Figure 8: Corresponding Anonymized Message
9. Security Considerations
This document provides guidelines for exporting metadata about
anonymized data in IPFIX, or storing metadata about anonymized data
in IPFIX Files. It is not intended as a general statement on the
applicability of specific flow data anonymization techniques.
Exporters or publishers of anonymized data must take care that the
applied anonymization technique is appropriate for the data source,
Boschi & Trammell Expires July 23, 2011 [Page 39]
Internet-Draft IP Flow Anonymization Support January 2011
the purpose, and the risk of deanonymization of a given application.
Research in anonymization techniques, and techniques for
deanonymization, is ongoing, and currently "safe" anonymization
techniques may be rendered unsafe by future developments.
We note specifically that anonymization is not a replacement for
encryption for confidentiality. It is only appropriate for
protecting identifying information in data to be used for purposes in
which the protected data is irrelevant. Confidentiality in export is
best served by using TLS [RFC5246] or DTLS [RFC4347] as in the
Security Considerations section of [RFC5101], and in long-term
storage by implementation-specific protection applied as in the
Security Considerations section of [RFC5655]. Indeed,
confidentiality and anonymization are not mutually exclusive, as
encryption for confidentiality may be applied to anonymized data
export or storage, as well, when the anonymized data is not intended
for public release.
We note as well that care should be taken even with well-anonymized
data, and anonymized data should still be treated as privacy-
sensitive. Anonymization reduces the risk of misuse, but is not a
complete solution to the problem of protecting end-user privacy in
network flow trace analysis.
When using pseudonymization techniques that have a mutable mapping,
there is an inherent tradeoff in the stability of the map between
long-term comparability and security of the data set against
deanonymization. In general, deanonymization attacks are more
effective given more information, so the longer a given mapping is
valid, the more information can be applied to deanonymization. The
specific details of this are technique-dependent and therefore out of
the scope of this document.
When releasing anonymized data, publishers need to ensure that data
that could be used in deanonymization is not leaked through a side
channel. The entire workflow (hardware, software, operational
policies and procedures, etc.) for handling anonymized data must be
evaluated for risk of data leakage. While most of these possible
side channels are out of scope for this document, guidelines for
reducing the risk of information leakage specific to the IPFIX export
protocol are provided in Section 7.2.
Note as well that the Security Considerations section of [RFC5101]
applies as well to the export of anonymized data, and the Security
Considerations section of [RFC5655] to the storage of anonymized
data, or the publication of anonymized traces.
Boschi & Trammell Expires July 23, 2011 [Page 40]
Internet-Draft IP Flow Anonymization Support January 2011
10. IANA Considerations
This document specifies the creation of several new IPFIX Information
Elements in the IPFIX Information Element registry located at
http://www.iana.org/assignments/ipfix, as defined in Section 6.2
above. IANA has assigned the following Information Element numbers
for their respective Information Elements as specified below:
o Information Element number TBD1 for the anonymizationFlags
Information Element.
o Information Element number TBD2 for the anonymizationTechnique
Information Element.
o Information Element number TBD3 for the informationElementIndex
Information Element.
[NOTE for IANA: The text TBDn should be replaced with the respective
assigned Information Element numbers where they appear in this
document. Information Element numbers should be assigned outside the
NetFlow V9 compatibility range, as these Information Elements are not
supported by NetFlow V9.]
11. Acknowledgments
We thank Paul Aitken and John McHugh for their comments and insight,
and Carsten Schmoll, Benoit Claise, Lothar Braun, Dan Romascanu,
Stewart Bryant, and Sean Turner for their reviews. Special thanks to
the FP7 PRISM and DEMONS projects for their material support of this
work.
12. References
12.1. Normative References
[RFC5101] Claise, B., "Specification of the IP Flow Information
Export (IPFIX) Protocol for the Exchange of IP Traffic
Flow Information", RFC 5101, January 2008.
[RFC5102] Quittek, J., Bryant, S., Claise, B., Aitken, P., and J.
Meyer, "Information Model for IP Flow Information Export",
RFC 5102, January 2008.
[RFC5103] Trammell, B. and E. Boschi, "Bidirectional Flow Export
Using IP Flow Information Export (IPFIX)", RFC 5103,
January 2008.
Boschi & Trammell Expires July 23, 2011 [Page 41]
Internet-Draft IP Flow Anonymization Support January 2011
[RFC5655] Trammell, B., Boschi, E., Mark, L., Zseby, T., and A.
Wagner, "Specification of the IP Flow Information Export
(IPFIX) File Format", RFC 5655, October 2009.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC5735] Cotton, M. and L. Vegoda, "Special Use IPv4 Addresses",
BCP 153, RFC 5735, January 2010.
[RFC5156] Blanchet, M., "Special-Use IPv6 Addresses", RFC 5156,
April 2008.
12.2. Informative References
[RFC5470] Sadasivan, G., Brownlee, N., Claise, B., and J. Quittek,
"Architecture for IP Flow Information Export", RFC 5470,
March 2009.
[RFC5472] Zseby, T., Boschi, E., Brownlee, N., and B. Claise, "IP
Flow Information Export (IPFIX) Applicability", RFC 5472,
March 2009.
[I-D.ietf-ipfix-mediators-framework]
Kobayashi, A., Claise, B., Muenz, G., and K. Ishibashi,
"IPFIX Mediation: Framework",
draft-ietf-ipfix-mediators-framework-09 (work in
progress), October 2010.
[I-D.ietf-ipfix-export-per-sctp-stream]
Claise, B., Aitken, P., Johnson, A., and G. Muenz, "IPFIX
Export per SCTP Stream",
draft-ietf-ipfix-export-per-sctp-stream-08 (work in
progress), May 2010.
[RFC5153] Boschi, E., Mark, L., Quittek, J., Stiemerling, M., and P.
Aitken, "IP Flow Information Export (IPFIX) Implementation
Guidelines", RFC 5153, April 2008.
[RFC3917] Quittek, J., Zseby, T., Claise, B., and S. Zander,
"Requirements for IP Flow Information Export (IPFIX)",
RFC 3917, October 2004.
[RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing
Architecture", RFC 4291, February 2006.
[RFC4347] Rescorla, E. and N. Modadugu, "Datagram Transport Layer
Security", RFC 4347, April 2006.
Boschi & Trammell Expires July 23, 2011 [Page 42]
Internet-Draft IP Flow Anonymization Support January 2011
[RFC5246] Dierks, T. and E. Rescorla, "The Transport Layer Security
(TLS) Protocol Version 1.2", RFC 5246, August 2008.
[Bur10] Burkhart, M., Schatzmann, D., Trammell, B., and E. Boschi,
"The Role of Network Trace Anonymization Under Attack",
ACM Computer Communications Review, vol. 40, no. 1, pp.
6-11, January 2010.
[Mur07] Murdoch, S. and P. Zielinski, "Sampled Traffic Analysis by
Internet-Exchange-Level Adversaries", Proceedings of the
7th Workshop on Privacy Enhancing Technologies, Ottawa,
Canada., June 2007.
Authors' Addresses
Elisa Boschi
Swiss Federal Institute of Technology Zurich
Gloriastrasse 35
8092 Zurich
Switzerland
Email: boschie@tik.ee.ethz.ch
Brian Trammell
Swiss Federal Institute of Technology Zurich
Gloriastrasse 35
8092 Zurich
Switzerland
Phone: +41 44 632 70 13
Email: trammell@tik.ee.ethz.ch
Boschi & Trammell Expires July 23, 2011 [Page 43]
| PAFTECH AB 2003-2026 | 2026-04-23 04:07:15 |