One document matched: draft-ietf-hubmib-efm-epon-mib-01.txt
Differences from draft-ietf-hubmib-efm-epon-mib-00.txt
Ethernet Interfaces and Hub MIB Working Group Lior Khermosh, Editor
INTERNET DRAFT Passave Technologies
April 29, 2004
Managed Objects for the Ethernet Passive Optical Networks
<draft-ietf-hubmib-efm-epon-mib-01.txt>
Status of this Memo
This document is an Internet-Draft and is subject to all provisions of
Section 10 of RFC2026. Internet-Drafts are working documents of the
Internet Engineering Task Force (IETF), its areas, and its working
groups. Note that other groups may also distribute working documents
as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsolete by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
Copyright Notice
Copyright (C) The Internet Society (2003). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published and
distributed, in whole or in part, without restriction of any kind,
provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of developing
Internet standards in which case the procedures for copyrights defined
in the Internet Standards process must be followed, or as required to
translate it into languages other than English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN
WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
EPON MIB WG Expires October 2004 [Page 1]
Internet-Draft EPON MIBs April 29, 2004
Abstract
This document defines a portion of the Management Information Base
(MIB) for use with network management protocols in TCP/IP based
Internets. In particular, it defines objects for managing devices and
interfaces that conform to the Ethernet Passive Optical Networks
(EPON) standards as defined in [802.3ah]. The document contains a list
of management entities based on the registers defined in the Institute
of Electrical and Electronic Engineers, IEEE Draft 802.3ah-2002 Draft
3.2 Annex 30A and mainly partitioned accordingly.
EPON MIB WG Expires October 2004 [Page 2]
Internet-Draft EPON MIBs April 29, 2004
Table of Content
Status of this Memo 1
Copyright Notice 1
Abstract 2
Table of Content 3
Terminology 4
1 The Internet-Standard Management Framework 4
2 Overview 4
2.1 Relationship of the EFM EPON MIB to the Interfaces MIB
, the Ethernet-like Interfaces MIB and the MAU MIB 4
2.2 Relationship of the EFM EPON MIB to the Generic EFM MIB 4
2.3 Relationship of the EPON Device MIB to the EFM EPON MIB 4
2.4 Relationship of the EPON Device MIB to the Optical
Interface MIBs 5
2.5 Relationship of the EPON Device MIB to the bridge MIB 5
3 MIB structure 5
4 Definitions û The EFM EPON MIB 6
5 Relationship table of the EFM EPON MIBs objects to the
IEEE802.3ah objects 32
6 Definitions - The EPON Device MIB 34
7 Security Considerations 63
8 Intellectual Property 64
9 Normative References 65
10 Informative References 66
Copyright Notice 67
AuthorÆs information 67
EPON MIB WG Expires October 2004 [Page 3]
Internet-Draft EPON MIBs April 29, 2004
Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL", when used in the guidelines in this memo, are to be
interpreted as described in RFC 2119 [RFC2119].
1 The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a MIB
module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580].
2 Overview
This document defines a portion of the Management Information Base
(MIB) for use with network management protocols in TCP/IP based
Internets. In particular, it defines objects for managing devices and
interfaces that conform to the Ethernet Passive Optical Networks
(EPON) standards as defined in [802.3ah]. The document contains a list
of management entities based on the registers defined in the [802.3ah]
Annex 30A and mainly partitioned accordingly.
The document also contains a device group section defining the MIBs
for EPON form a device perspective, which are connected directly to
the IEEE 802.3ah layer2 specifications.
The document also provides amendments to the 802.3 MAU MIBs documents
for the EFM device type addition.
2.1 Relationship of the EFM EPON MIB to the Interfaces MIB, the
Ethernet-like Interfaces MIB and the MAU MIB EFM EPON interfaces
require implementation of Interfaces MIB [RFC2863], Ethernet-like
Interfaces MIB [RFC2665] and MAU-MIB [RFC3636].
The MIBs defined in this document are an extension for these MIBs. For
instance defining dot3MpcpRemoteMACAddress only while assuming the
local MAC address attribute is already defined in [RFC 2665].
2.2 Relationship of the EFM EPON MIB to the Generic EFM MIB
EFM EPON interfaces require implementation of Generic EFM MIB [draft-
ietf-hubmibùefm-mib]. This document defines general EFM attributes and
managed objects that are referred in the document.
2.3 Relationship of the EPON Device MIB to EFM EPON MIB
EPON devices require implementation of the EFM EPON MIBs which are
EPON MIB WG Expires October 2004 [Page 4]
Internet-Draft EPON MIBs April 29, 2004
specified in this document. The opposite is not required as it
possible to implement the EFM interfaces by itself.
2.4 Relationship of the EPON Device MIB to Optical interface MIB
EPON devices may implement the Optical interface MIB [RFC3591]. This
document defines optical interface attributes and managed objects that
are assumed to be used by an EPON device.
2.5 Relationship of the EPON Device MIB to bridge MIB
EPON OLT devices may implement the bridge MIBs [RFC1493], [RFC1525],
Where the LLIDs of the PON are referred as the bridge ports. This
document defines managed objects for a bridge that are assumed to be
used by an EPON OLT device which bridges the data between the LLIDs of
the PON.
3 MIB structure
This document includes two MIBs the first is the EFM EPON MIBs and the
second is the EPON device MIBs.
The EFM EPON MIBs defines the objects used for configuration and
description of the [802.3ah] P2MP section.
These MIB objects are included of three MIB groups.
The MPCP MIBs definition û MIBs related to [802.3ah] clause 64 Multi
Point Control Protocol attributes. In this MIB group:
The dot3MpcpTable defines the objects used for the configuration and
description of the status of MPCP compliant interfaces.
The dot3MpcpStatTable defines the statistics group for MPCP compliant
interfaces.
The OMPEmulation MIBs definitions û MIBs related to [802.3ah] clause
65 point to point emulation attributes. In this MIB group:
The dot3OmpEmulationTable defines the objects used for the
configuration and description of the status of OMPEmulation
compliant interfaces.
The dot3OmpEmulationStatTable defines the statistics group for
OMPEmulation compliant interfaces.
The MAU MIBs definition including MAU type definitions and EPON MAU
managed object related to [802.3ah] clause 60 and clause 65.
The dot3EponMauTable defines the objects used for the configuration
and description of the status of MAU EPON compliant interfaces.
The dot3EponMauType defines the Type group for [802.3] EPOM MAUs.
Editor note - The MAU Type object should probably be with other 802.3
MAU type objects [RFC 3636].
The EPON Device MIBs defines the objects used for configuration and
description of management objects for EPON compliant Devices.
The eponDeviceTable defines the objects used for the configuration and
description of the EPON compliant devices.
EPON MIB WG Expires October 2004 [Page 5]
Internet-Draft EPON MIBs April 29, 2004
4 Definitions û The EFM EPON MIB (See section 30.2.5 in 802.3ah draft
for details):
DOT3-EFM-EPON-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, mib-2, OBJECT-TYPE, Counter32,
Integer32, OBJECT-IDENTITY
FROM SNMPv2-SMI
TruthValue, MacAddress
FROM SNMPv2-TC
ifIndex
FROM IF-MIB
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
;
dot3EfmeponMIB MODULE-IDENTITY
LAST-UPDATED "200404290000Z" -- April 29, 2004
ORGANIZATION "IETF Ethernet Interfaces and Hub MIB
Working Group"
CONTACT-INFO
"WG charter:
http://www.ietf.org/html.charters/hubmib-charter.html
Mailing Lists:
General Discussion: hubmib@ietf.org
To Subscribe: hubmib-request@ietf.org
In Body: subscribe your_email_address
Chair: Dan Romascanu
Postal: Avaya Inc.
Atidim Technology Park, Bldg. 3
Tel Aviv 61131
Israel
Tel: +972-3-645-8414
E-mail: dromasca@avaya.com
Editor: Lior Khermosh
Postal: Passave Technologies Inc.
Ackerstein Towers, Tower A, 6th floor,
9 Hamenofim St.
Hertzliya Pituach 46725,
ISRAEL
P.O.Box 2089 Hertzliya Pituach 46120 Israel
Tel: +972-9-9717600 Ext: 7181
E-mail: lior.khermosh@passave.com"
DESCRIPTION
"The objects in this MIB module are used to manage
EPON MIB WG Expires October 2004 [Page 6]
Internet-Draft EPON MIBs April 29, 2004
the Ethernet in the First Mile (EFM) Multi Point Control
Protocol (MPCP) Interfaces as defined in IEEE Draft
P802.3ah/D3.0 clause 64,65.
The following reference is used throughout this MIB module:
[802.3ah] refers to:
IEEE Draft P802.3ah/D3.3: 'Draft amendment to -
Information technology - Telecommunications and
information exchange between systems - Local and
metropolitan area networks - Specific requirements -
Part 3: Carrier sense multiple access with collision
detection (CSMA/CD) access method and physical layer
specifications - Media Access Control Parameters,
Physical Layers and Management Parameters for
subscriber access networks', 22 April 2004.
Of particular interest are Clause 64(MPCP) 65(P2mP RS) and
60 (PON PMDs). Clause 30, 'Management', and Clause
45,'Management Data Input/Output (MDIO) Interface'.
Copyright (C) The Internet Society (2003). This version
of this MIB module is part of XXXX see the RFC
itself for full legal notices."
-- Editor's Note: Replace XXXX with the actual RFC number
-- assigned by RFC Editor and remove this note
REVISION "200404290000Z" -- April 29, 2004
DESCRIPTION "Initial version, published as RFC XXXX."
::= { mib-2 XXX }
-- Editor's Note: Replace XXX with a real OID once it is
-- assigned by IANA and remove this note.
-- EditorÆs note: MPCP MIBs definitions ([802.3ah] clause 30.3.5)
-- EditorÆs note: Description in attributes with References should be
-- minimized in later versions
dot3MpcpMIB OBJECT IDENTIFIER ::= { dot3EfmeponMIB 1}
dot3MpcpObjects OBJECT IDENTIFIER ::= { dot3MpcpMIB 1}
dot3MpcpConformance OBJECT IDENTIFIER ::= { dot3MpcpMIB 2}
dot3MpcpTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot3MpcpEntry
EPON MIB WG Expires October 2004 [Page 7]
Internet-Draft EPON MIBs April 29, 2004
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table for dot3 MPCP MIBs."
::= { dot3MpcpObjects 1 }
dot3MpcpEntry OBJECT-TYPE
SYNTAX Dot3MpcpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the dot3 MPCP MIBs table."
INDEX { ifIndex }
::= { dot3MpcpTable 1 }
Dot3MpcpEntry ::=
SEQUENCE {
dot3MpcpID Integer32,
dot3MpcpAdminState TruthValue,
dot3MpcpMode INTEGER,
dot3MpcpLinkID Integer32,
dot3MpcpRemoteMACAddress MacAddress,
dot3MpcpRegistrationState INTEGER,
dot3MpcpTransmitElapsed Integer32,
dot3MpcpReceiveElapsed Integer32,
dot3MpcpRoundTripTime Integer32,
dot3MpcpMaximumPendingGrants Integer32,
dot3MPCPAdminControl TruthValue,
dot3MpcpOnTime Integer32,
dot3MpcpOffTime Integer32,
dot3MpcpSyncTime Integer32
}
dot3MpcpID OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable is assigned so as to uniquely identify the Multi-Point
MAC Control (MPCP) entity, as defined in [802.3ah] clause 64, among
the subordinate managed objects of the containing object."
REFERENCE "[802.3ah], 30.3.5.1.1."
::= { dot3MpcpEntry 1 }
dot3MpcpAdminState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
EPON MIB WG Expires October 2004 [Page 8]
Internet-Draft EPON MIBs April 29, 2004
STATUS current
DESCRIPTION
"This variable can be used to define the operational state of the
Multi-Point MAC Control sublayer as defined in [802.3ah] clause 64.
Selecting admin for an interface with Multi-Point MAC Control
sublayer"
REFERENCE "[802.3ah], 30.3.5.1.2."
::= { dot3MpcpEntry 2 }
dot3MpcpMode OBJECT-TYPE
SYNTAX INTEGER {
olt(1),
onu(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable can be used to identify the operational state of the
Multi-Point MAC Control sublayer as defined in [802.3ah] clause 64.
Selecting olt for an OLT (server) mode and onu for an ONU (client)
mode."
REFERENCE "[802.3ah], 30.3.5.1.3."
::= { dot3MpcpEntry 3 }
dot3MpcpLinkID OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only value that identifies the Logical Link identity (LLID)
associated with the MAC port as specified in [802.3ah] clause
65.1.3.2.2."
REFERENCE "[802.3ah], 30.3.5.1.4."
::= { dot3MpcpEntry 4 }
dot3MpcpRemoteMACAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only value that identifies the source_address parameter of the
last MPCPDUs passed to the MAC Control. This value is updated on
reception of a valid frame with (1) a destination Field equal to the
reserved multicast address for MAC Control specified in [802.3ah]
Annex 31A, (2) lengthOrType field value equal to the reserved Type for
MAC Control as specified in [802.3ah] Annex 31A. (3) an MPCP subtype
value equal to the subtype reserved for MPCP as specified in [802.3ah]
Annex 31A."
EPON MIB WG Expires October 2004 [Page 9]
Internet-Draft EPON MIBs April 29, 2004
REFERENCE "[802.3ah], 30.3.5.1.5."
::= { dot3MpcpEntry 5 }
dot3MpcpRegistrationState OBJECT-TYPE
SYNTAX INTEGER {
unregistered(1),
registering(2),
registered(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only value that identifies the operational state of the Multi-
Point MAC Control sublayer as defined in [802.3ah] clause 64. When
this attribute has the enumeration 'unregistered' the interface may be
used for registering a link partner. When this attribute has the
enumeration 'registering' the interface is in the process of
registering a link-partner. When this attribute has the enumeration
'registered' the interface has an established link-partner."
REFERENCE "[802.3ah], 30.3.5.1.6."
::= { dot3MpcpEntry 6 }
dot3MpcpTransmitElapsed OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only value that reports the interval from last MPCP frame
transmission in increments of 16ns. The value returned shall be
(interval from last MPCP frame transmission in ns)/16, where this
value exceeds (2^32-1) the value (2^32-1) shall be returned."
REFERENCE "[802.3ah], 30.3.5.1.19."
::= { dot3MpcpEntry 7 }
dot3MpcpReceiveElapsed OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only value that reports the interval from last MPCP frame
reception in increments of 16ns. The value returned shall be (interval
from last MPCP last MPCP frame reception in ns)/16, where this value
exceeds (2^32-1) the value (2^32-1) shall be returned."
REFERENCE "[802.3ah], 30.3.5.1.20."
::= { dot3MpcpEntry 8 }
dot3MpcpRoundTripTime OBJECT-TYPE
EPON MIB WG Expires October 2004 [Page 10]
Internet-Draft EPON MIBs April 29, 2004
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only value that reports the MPCP round trip time in increments
of 16ns. The value returned shall be (round trip time in ns)/16, where
this value exceeds (2^16-1) the value (2^16-1) shall be returned."
REFERENCE "[802.3ah], 30.3.5.1.21."
::= { dot3MpcpEntry 9 }
dot3MpcpMaximumPendingGrants OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A read-only value that indicates the maximum number of grants an ONU
can store. The maximum number of grants an ONU can store has a range
of 0 to 255."
REFERENCE "[802.3ah], 30.3.5.1.24."
::= { dot3MpcpEntry 10 }
dot3MPCPAdminControl OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable can be used to define the operational state of the
Multi-Point MAC Control sublayer as defined in [802.3ah] clause 64.
Selecting admin for an interface with Multi-Point MAC Control
sublayer."
REFERENCE "[802.3ah], 30.3.5.2.1."
::= { dot3MpcpEntry 11 }
dot3MpcpOnTime OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only value that reports the æon timeÆ for a grant burst in
increments of 16ns as defined in [802.3ah] 60,64. The value returned
shall
be (on time ns)/16, where this value exceeds (2^32-1) the value (2^32-
1) shall be returned."
REFERENCE "[802.3ah], 64.3.5.1."
::= { dot3MpcpEntry 12 }
dot3MpcpOffTime OBJECT-TYPE
EPON MIB WG Expires October 2004 [Page 11]
Internet-Draft EPON MIBs April 29, 2004
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only value that reports the æoff timeÆ for a grant burst in
increments of 16ns as defined in [802.3ah] 60,64. The value returned
shall be (off time ns)/16, where this value exceeds (2^32-1) the value
(2^32-1) shall be returned."
REFERENCE "[802.3ah], 64.3.5.1."
::= { dot3MpcpEntry 13 }
dot3MpcpSyncTime OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only value that reports the æsync lock timeÆ for an OLT
receiver in increments of 16ns as defined in [802.3ah] 60,64,65. The
value returned shall be (sync lock time ns)/16, where this value
exceeds (2^32-1) the value (2^32-1) shall be returned."
REFERENCE "[802.3ah], 64.3.3.2."
::= { dot3MpcpEntry 14 }
dot3MpcpStatTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot3MpcpStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table defines the list of statistics counters of [802.3ah]
clause 64 MPCP interface."
::= { dot3MpcpObjects 2 }
dot3MpcpStatEntry OBJECT-TYPE
SYNTAX Dot3MpcpStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table entries for Table of statistics counters of [802.3ah] clause
64
MPCP interface."
INDEX { ifIndex }
::= { dot3MpcpStatTable 1 }
Dot3MpcpStatEntry ::=
SEQUENCE {
EPON MIB WG Expires October 2004 [Page 12]
Internet-Draft EPON MIBs April 29, 2004
dot3MpcpMACCtrlFramesTransmitted Counter32,
dot3MpcpMACCtrlFramesReceived Counter32,
dot3MpcpDiscoveryWindowsSent Counter32,
dot3MpcpDiscoveryTimeout Counter32,
dot3MpcpTxRegRequest Counter32,
dot3MpcpRxRegRequest Counter32,
dot3MpcpTxRegAck Counter32,
dot3MpcpRxRegAck Counter32,
dot3MpcpTxReport Counter32,
dot3MpcpRxReport Counter32,
dot3MpcpTxGate Counter32,
dot3MpcpRxGate Counter32,
dot3MpcpTxRegister Counter32,
dot3MpcpRxRegister Counter32,
dot3MpcpRxNotSupportedMPCP Counter32
}
dot3MpcpMACCtrlFramesTransmitted OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of MPCP frames passed to the MAC sublayer for transmission.
This counter is incremented when a MA_CONTROL.request service
primitive is generated within the MAC control sublayer with an opcode
indicating a MPCP frame."
REFERENCE "[802.3ah], 30.3.5.1.7."
::= { dot3MpcpStatEntry 1 }
dot3MpcpMACCtrlFramesReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of MPCP frames passed by the MAC sublayer to the MAC Control
sublayer. This counter is incremented when a ReceiveFrame function
call returns a valid frame with: (1) a lengthOrType field value equal
to the reserved Type for 802.3_MAC_Control as specified in 31.4.1.3,
and (2) an opcode indicating a MPCP frame."
REFERENCE "[802.3ah], 30.3.5.1.8."
::= { dot3MpcpStatEntry 2}
dot3MpcpDiscoveryWindowsSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
EPON MIB WG Expires October 2004 [Page 13]
Internet-Draft EPON MIBs April 29, 2004
STATUS current
DESCRIPTION
"A count of discovery windows generated. The counter is incremented by
one for each generated discovery window."
REFERENCE "[802.3ah], 30.3.5.1.22."
::= { dot3MpcpStatEntry 3}
dot3MpcpDiscoveryTimeout OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the number of times a discovery timeout occurs. Increment
the counter by one for each discovery processing state-machine reset
resulting from timeout waiting for message arrival."
REFERENCE "[802.3ah], 30.3.5.1.23."
::= { dot3MpcpStatEntry 4}
dot3MpcpTxRegRequest OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the number of times a REGISTER_REQ MPCP frames
transmission occurs. Increment the counter by one for each
REGISTER_REQ MPCP frame transmitted as defined in [802.3ah] clause 64.
This counter is mandatory for an ONU"
REFERENCE "[802.3ah], 30.3.5.1.12."
::= { dot3MpcpStatEntry 5}
dot3MpcpRxRegRequest OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the number of times a REGISTER_REQ MPCP frames reception
occurs. A single counter at the ONU and a set of counters, one for
each LLID, at the OLT. Increment the counter by one for each
REGISTER_REQ MPCP frame received for each LLID as defined in [802.3ah]
clause 64. This counter is mandatory for an ONU and for an OLT"
REFERENCE "[802.3ah], 30.3.5.1.17."
::= { dot3MpcpStatEntry 6}
dot3MpcpTxRegAck OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
EPON MIB WG Expires October 2004 [Page 14]
Internet-Draft EPON MIBs April 29, 2004
STATUS current
DESCRIPTION
" A count of the number of times a REGISTER_ACK MPCP frames
transmission occurs. Increment the counter by one for each
REGISTER_ACK MPCP frame transmitted as defined in [802.3ah] clause 64.
This counter is mandatory for an ONU"
REFERENCE "[802.3ah], 30.3.5.1.10."
::= { dot3MpcpStatEntry 7}
dot3MpcpRxRegAck OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a REGISTER_ACK MPCP frames reception
occurs. A single counter at the ONU and a set of counters, one for
each LLID, at the OLT. Increment the counter by one for each
REGISTER_ACK MPCP frame received for each LLID, as defined in
[802.3ah] clause 64. This counter is mandatory for an ONU and for an
OLT"
REFERENCE "[802.3ah], 30.3.5.1.15."
::= { dot3MpcpStatEntry 8}
dot3MpcpTxReport OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a REPORT MPCP frames transmission
occurs. Increment the counter by one for each REPORT MPCP frame
transmitted as defined in [802.3ah] clause 64. This counter is
mandatory for an ONU."
REFERENCE "[802.3ah], 30.3.5.1.13."
::= { dot3MpcpStatEntry 9}
dot3MpcpRxReport OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a REPORT MPCP frames reception
occurs. A single counter at the ONU and a set of counters, one for
each LLID, at the OLT. Increment the counter by one for each REPORT
MPCP frame received for each LLID, as defined in [802.3ah] clause 64.
This counter is mandatory for an ONU and for an OLT."
REFERENCE "[802.3ah], 30.3.5.1.18."
::= { dot3MpcpStatEntry 10}
EPON MIB WG Expires October 2004 [Page 15]
Internet-Draft EPON MIBs April 29, 2004
dot3MpcpTxGate OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the number of times a GATE MPCP frames transmission
occurs. A set of counters, one for each LLID, at the OLT. Increment
the counter by one for each GATE MPCP frame transmitted, for each
LLID, as defined in [802.3ah] clause 64. This counter is mandatory for
an OLT."
REFERENCE "[802.3ah], 30.3.5.1.9."
::= { dot3MpcpStatEntry 11}
dot3MpcpRxGate OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the number of times a GATE MPCP frames reception occurs. A
single counter at the ONU and a set of counters, one for each LLID, at
the OLT. Increment the counter by one for each GATE MPCP frame
received, for each LLID, as defined in [802.3ah] clause 64. This
counter is mandatory for an ONU and for an OLT."
REFERENCE "[802.3ah], 30.3.5.1.14."
::= { dot3MpcpStatEntry 12}
dot3MpcpTxRegister OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the number of times a REGISTER MPCP frames transmission
occurs. A set of counters, one for each LLID, at the OLT. Increment
the
counter by one for each REGISTER MPCP frame transmitted, for each
LLID, as defined in [802.3ah] clause 64. This counter is mandatory for
an OLT."
REFERENCE "[802.3ah], 30.3.5.1.11."
::= { dot3MpcpStatEntry 13}
dot3MpcpRxRegister OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the number of times a REGISTER MPCP frames reception
occurs. A single counter at the ONU and a set of counters, one for
each LLID, at the OLT. Increment the counter by one for each REGISTER
MPCP frame received, for each LLID, as defined in [802.3ah] clause 64.
This counter
EPON MIB WG Expires October 2004 [Page 16]
Internet-Draft EPON MIBs April 29, 2004
is mandatory for an ONU and for an OLT."
REFERENCE "[802.3ah], 30.3.5.1.16."
::= { dot3MpcpStatEntry 14}
dot3MpcpRxNotSupportedMPCP OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a non-supported MPCP frames reception
occurs. A single counter at the ONU and a set of counters, one for
each LLID, at the OLT. Increment the counter by one for each non-
supported MPCP frame received, for each LLID, as defined in [802.3ah]
clause 64. This counter is mandatory for an ONU and for an OLT."
::= { dot3MpcpStatEntry 15}
-- Conformance Statements
-- Conformance Groups
dot3MpcpGroups OBJECT IDENTIFIER ::= { dot3MpcpConformance 1 }
dot3MpcpGroupBase OBJECT-GROUP
OBJECTS {
dot3MpcpID,
dot3MpcpAdminState,
dot3MpcpMode,
dot3MpcpLinkID,
dot3MpcpRemoteMACAddress,
dot3MpcpRegistrationState,
dot3MpcpMaximumPendingGrants,
dot3MPCPAdminControl
}
STATUS current
DESCRIPTION
"A collection of objects of dot3 Mpcp Basic entity state
EPON MIB WG Expires October 2004 [Page 17]
Internet-Draft EPON MIBs April 29, 2004
definition."
::= { dot3MpcpGroups 1 }
dot3MpcpGroupParam OBJECT-GROUP
OBJECTS {
dot3MpcpTransmitElapsed,
dot3MpcpReceiveElapsed,
dot3MpcpRoundTripTime,
dot3MpcpOnTime,
dot3MpcpOffTime,
dot3MpcpSyncTime
}
STATUS current
DESCRIPTION
"A collection of objects of dot3 Mpcp for P2MP
parameters."
::= { dot3MpcpGroups 2 }
dot3MpcpGroupStat OBJECT-GROUP
OBJECTS {
dot3MpcpMACCtrlFramesTransmitted,
dot3MpcpMACCtrlFramesReceived,
dot3MpcpDiscoveryWindowsSent,
dot3MpcpDiscoveryTimeout ,
dot3MpcpTxRegRequest,
dot3MpcpRxRegRequest,
dot3MpcpTxRegAck,
dot3MpcpRxRegAck,
dot3MpcpTxReport,
dot3MpcpRxReport,
dot3MpcpTxGate,
dot3MpcpRxGate,
dot3MpcpTxRegister,
dot3MpcpRxRegister,
dot3MpcpRxNotSupportedMPCP
}
STATUS current
DESCRIPTION
"A collection of objects of dot3 Mpcp Statistics"
::= { dot3MpcpGroups 3 }
EPON MIB WG Expires October 2004 [Page 18]
Internet-Draft EPON MIBs April 29, 2004
-- Compliance
dot3MpcpCompliances OBJECT IDENTIFIER ::= { dot3MpcpConformance 2 }
dot3MPCPCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION "The compliance statement for Multi-point
control protocol interfaces."
MODULE -- this module
MANDATORY-GROUPS { dot3MpcpGroupBase}
GROUP dot3MpcpGroupParam
DESCRIPTION "This group is mandatory for all
MPCP supporting interfaces
for configuration of the Multipoint
Parametrs."
GROUP dot3MpcpGroupStat
DESCRIPTION " This group is mandatory for all
MPCP supporting interfaces
for Statistics collection."
::= { dot3MpcpCompliances 1}
-- EditorÆs note: OMPEmulation managed object definitions
dot3OmpEmulationMIB OBJECT IDENTIFIER ::= { dot3EfmeponMIB 2}
dot3OmpEmulationObjects OBJECT IDENTIFIER ::= { dot3OmpEmulationMIB 1}
dot3OmpeConformance OBJECT IDENTIFIER ::= { dot3OmpEmulationMIB 2 }
dot3OmpEmulationTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot3OmpEmulationEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table for dot3 OmpEmulation MIBs."
::= { dot3OmpEmulationObjects 1 }
dot3OmpEmulationEntry OBJECT-TYPE
EPON MIB WG Expires October 2004 [Page 19]
Internet-Draft EPON MIBs April 29, 2004
SYNTAX Dot3OmpEmulationEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the dot3 OmpEmulation MIBs table."
INDEX { ifIndex }
::= { dot3OmpEmulationTable 1 }
Dot3OmpEmulationEntry ::=
SEQUENCE {
dot3OmpEmulationID Integer32,
dot3OmpEmulationType INTEGER
}
dot3OmpEmulationID OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The value of aOAMID is assigned so as to uniquely identify a
OMPEmulation entity among the subordinate managed objects of the
containing object."
REFERENCE "[802.3ah], 30.3.7.1.1."
::= { dot3OmpEmulationEntry 1}
dot3OmpEmulationType OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
olt(2),
onu(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A read-only value that indicates that mode of operation of the
Reconciliation Sublayer for Point to Point Emulation (see [802.3ah]
clause 65.1). æunknownÆ value is assigned in initializing, true state
or type not yet known. æoltÆ value is assigned when Sublayer operating
in OLT mode. æonuÆ value is assigned when Sublayer operating in ONU
mode."
REFERENCE "[802.3ah], 30.3.7.1.2."
::= { dot3OmpEmulationEntry 2}
dot3OmpEmulationStatTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot3OmpEmulationStatEntry
EPON MIB WG Expires October 2004 [Page 20]
Internet-Draft EPON MIBs April 29, 2004
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table defines the list of statistics counters of [802.3ah]
clause 65 OMP interface."
::= { dot3OmpEmulationObjects 2}
dot3OmpEmulationStatEntry OBJECT-TYPE
SYNTAX Dot3OmpEmulationStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table entries for Table of statistics counters of [802.3ah] clause
65 OMP interface."
INDEX { ifIndex }
::= { dot3OmpEmulationStatTable 1 }
Dot3OmpEmulationStatEntry::=
SEQUENCE {
dot3OmpEmulationSLDErrors Counter32,
dot3OmpEmulationCRC8Errors Counter32,
dot3OmpEmulationBadLLID Counter32,
dot3OmpEmulationGoodLLID Counter32,
dot3OmpEmulationOnuPonCastLLID Counter32,
dot3OmpEmulationOltPonCastLLID Counter32,
dot3OmpEmulationBroadcastLLIDNotOnuID Counter32,
dot3OmpEmulationOnuLLIDNotBroadcast Counter32,
dot3OmpEmulationBroadcastLLIDPlusOnuId Counter32,
dot3OmpEmulationNotBroadcastLLIDNotOnuId Counter32
}
dot3OmpEmulationSLDErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of frames received that do not contain a valid SLD field as
defined in [802.3ah] clause 65.1.3.3.1. This attribute is mandatory
for a OLT and optional for a ONU."
REFERENCE "[802.3ah], 30.3.7.1.3."
::= { dot3OmpEmulationStatEntry 1}
dot3OmpEmulationCRC8Errors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
EPON MIB WG Expires October 2004 [Page 21]
Internet-Draft EPON MIBs April 29, 2004
"A count of frames received that contain a valid SLD field, as defined
in [802.3ah] clause 65.1.3.3.1, but do not pass the CRC-8 check as
defined in [802.3ah] clause 65.1.3.3.3. This attribute is mandatory
for a OLT and optional for a ONU."
REFERENCE "[802.3ah], 30.3.7.1.4."
::= { dot3OmpEmulationStatEntry 2}
dot3OmpEmulationBadLLID OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of frames received that contain a valid SLD field in a OLT,
as defined in [802.3ah] clause 65.1.3.3.1, and pass the CRC-8 check,
as defined in [802.3ah] clause 65.1.3.3.3, but are discarded due to
the LLID check as defined in [802.3ah] clause 65.1.3.3.2."
REFERENCE "[802.3ah], 30.3.7.1.8."
::= { dot3OmpEmulationStatEntry 3}
dot3OmpEmulationGoodLLID OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of frames received that contain a valid SLD field in a OLT,
as defined in [802.3ah] clause 65.1.3.3.1, and pass the CRC-8 check,
as defined in [802.3ah] clause 65.1.3.3.3"
REFERENCE "[802.3ah], 30.3.7.1.5."
::= { dot3OmpEmulationStatEntry 4}
dot3OmpEmulationOnuPonCastLLID OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of frames received that contain a valid SLD field in an ONU,
as defined in [802.3ah] 65.1.3.3.1, passes the CRC-8 check, as defined
in [802.3ah] 65.1.3.3.3, and the frame meets the rule for acceptance
defined in [802.3ah] 65.1.3.3.2."
REFERENCE "[802.3ah], 30.3.7.1.6."
::= { dot3OmpEmulationStatEntry 5}
dot3OmpEmulationOltPonCastLLID OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
EPON MIB WG Expires October 2004 [Page 22]
Internet-Draft EPON MIBs April 29, 2004
STATUS current
DESCRIPTION
"A count of frames received that contain a valid SLD field in an OLT,
as defined in [802.3ah] 65.1.3.3.1, passes the CRC-8 check, as defined
in [802.3ah] 65.1.3.3.3, and the frame meets the rule for acceptance
defined in [802.3ah] 65.1.3.3.2."
REFERENCE "[802.3ah], 30.3.7.1.7."
::= { dot3OmpEmulationStatEntry 6}
dot3OmpEmulationBroadcastLLIDNotOnuID OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of frames received that contain a valid SLD field in a OLT,
as defined in [802.3ah] clause 65.1.3.3.1, and pass the CRC-8 check,
as defined in [802.3ah] clause 65.1.3.3.3, and contain broadcast LLID
as defined in [802.3ah] clause 65. This attribute is mandatory for a
OLT and for a ONU."
::= { dot3OmpEmulationStatEntry 7}
dot3OmpEmulationOnuLLIDNotBroadcast OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of frames received that contain a valid SLD field in a OLT,
as defined in [802.3ah] clause 65.1.3.3.1, and pass the CRC-8 check,
as defined in [802.3ah] clause 65.1.3.3.3, and contain the ONUÆs LLID
as defined in [802.3ah] clause 65. This attribute is mandatory for an
ONU and mandatory for a OLT (a counter per LLID)."
::= { dot3OmpEmulationStatEntry 8}
dot3OmpEmulationBroadcastLLIDPlusOnuId OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of frames received that contain a valid SLD field in a OLT,
as defined in [802.3ah] clause 65.1.3.3.1, and pass the CRC-8 check,
as defined in [802.3ah] clause 65.1.3.3.3, and contain the broadcast
LLID plus ONUÆs LLID (frame reflected) as defined in [802.3ah] clause
65. This attribute is mandatory for an ONU and mandatory for a OLT (a
counter per LLID)."
::= { dot3OmpEmulationStatEntry 9}
EPON MIB WG Expires October 2004 [Page 23]
Internet-Draft EPON MIBs April 29, 2004
dot3OmpEmulationNotBroadcastLLIDNotOnuId OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of frames received that contain a valid SLD field in a OLT,
as defined in [802.3ah] clause 65.1.3.3.1, and pass the CRC-8 check,
as defined in [802.3ah] clause 65.1.3.3.3, and does not contain the
ONUÆs LLID as defined in [802.3ah] clause 65. This attribute is
mandatory for an ONU"
::= { dot3OmpEmulationStatEntry 10}
-- Conformance Statements
-- Conformance Groups
dot3OmpeGroups OBJECT IDENTIFIER ::={ dot3OmpeConformance 1}
dot3OmpeGroupID OBJECT-GROUP
OBJECTS {
dot3OmpEmulationID,
dot3OmpEmulationType
}
STATUS current
DESCRIPTION
"A collection of objects of dot3 OMP emulation ID entity
state definition."
::= { dot3OmpeGroups 1 }
dot3OmpeGroupStat OBJECT-GROUP
OBJECTS {
dot3OmpEmulationSLDErrors,
dot3OmpEmulationCRC8Errors,
dot3OmpEmulationBadLLID,
dot3OmpEmulationGoodLLID,
dot3OmpEmulationOnuPonCastLLID,
dot3OmpEmulationOltPonCastLLID,
dot3OmpEmulationBroadcastLLIDNotOnuID,
dot3OmpEmulationOnuLLIDNotBroadcast,
EPON MIB WG Expires October 2004 [Page 24]
Internet-Draft EPON MIBs April 29, 2004
dot3OmpEmulationBroadcastLLIDPlusOnuId,
dot3OmpEmulationNotBroadcastLLIDNotOnuId
}
STATUS current
DESCRIPTION
"A collection of objects of dot3 OMP emulation
Statistics"
::= { dot3OmpeGroups 2 }
-- Compliance
dot3OmpeCompliances OBJECT IDENTIFIER ::= { dot3OmpeConformance 2 }
dot3OmpeCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION "The compliance statement for OMPEmulation
interfaces."
MODULE -- this module
MANDATORY-GROUPS { dot3OmpeGroupID}
GROUP dot3OmpeGroupStat
DESCRIPTION " This group is mandatory for all
OMPemulation supporting interfaces
for Statistics collection."
::= { dot3OmpeCompliances 1}
-- EditorÆs note: MAU managed object definitions (30.5.1)
dot3EponMauMIB OBJECT IDENTIFIER ::= { dot3EfmeponMIB 3}
dot3EponMauObjects OBJECT IDENTIFIER ::= { dot3EponMauMIB 1}
dot3EponMauConformance OBJECT IDENTIFIER ::= { dot3EponMauMIB 2 }
dot3EponMauTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dot3EponMauEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table for dot3 MAU EPON MIBs."
::= { dot3EponMauObjects 1 }
EPON MIB WG Expires October 2004 [Page 25]
Internet-Draft EPON MIBs April 29, 2004
dot3EponMauEntry OBJECT-TYPE
SYNTAX Dot3EponMauEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the dot3 MAU EPON MIBs table."
INDEX { ifIndex }
::= { dot3EponMauTable 1 }
Dot3EponMauEntry ::=
SEQUENCE {
dot3EponMauPCSCodingViolation Counter32,
dot3EponMauFecAbility INTEGER,
dot3EponMauFecMode INTEGER,
dot3EponMauFECCorrectedBlocks Counter32,
dot3EponMauFECUncorrectableBlocks Counter32,
dot3EponMauBufferHeadCodingViolation Counter32
}
dot3EponMauPCSCodingViolation OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" For 100 Mb/ s operation it is a count of the number of times an
invalid code-group is received, other than the /H/ code-group. For
1000 Mb/ s operation it is a count of the number of times an invalid
codegroup is received, other than the /V/ code-group."
REFERENCE "[802.3ah], 30.5.1.1.12."
::= { dot3EponMauEntry 1}
dot3EponMauFecAbility OBJECT-TYPE
SYNTAX INTEGER {
unknown (1),
nonsupported (2),
supported (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only value that indicates the support of operation of the
1000BASE-PX PHY optional FEC Sublayer for Forward error correction see
[802.3ah] clause 65.2).
æunknownÆ value is assigned in initializing, for non FEC support state
EPON MIB WG Expires October 2004 [Page 26]
Internet-Draft EPON MIBs April 29, 2004
or type not yet known. ænonsupportedÆ value is assigned when Sublayer
is not support. æsupportedÆ value is assigned when Sublayer is
supported."
REFERENCE "[802.3ah], 30.5.1.1.13."
::= { dot3EponMauEntry 2}
dot3EponMauFecMode OBJECT-TYPE
SYNTAX INTEGER {
unknown (1),
disabled (2),
enabled (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A read-write value that indicates the mode of operation of the
1000BASE-PX PHY optional FEC Sublayer for Forward error correction see
[802.3ah] clause 65.2).
A GET operation returns the current mode of operation the PHY. A SET
operation changes the mode of operation of the PHY to the indicated
value.
æunknownÆ value is assigned in initializing, for non FEC support state
or type not yet known. ædisabledÆ value is assigned when Sublayer
operating in disabled mode. æenabledÆ value is assigned when Sublayer
operating in FEC mode."
REFERENCE "[802.3ah], 30.5.1.1.14."
::= { dot3EponMauEntry 3}
dot3EponMauFECCorrectedBlocks OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" For 10PASS-TS, 2BASE-TL and 1000BASE-PX PHYs, a count of corrected
FEC
blocks. This counter will not increment for other PHY Types. Increment
the counter by one for each received block that is corrected by the
FEC function in the PHY."
REFERENCE "[802.3ah], 30.5.1.1.15."
::= { dot3EponMauEntry 4}
dot3EponMauFECUncorrectableBlocks OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" For 10PASS-TS, 2BASE-TL and 1000BASE-PX PHYs, a count of
uncorrectable FEC blocks. This counter will not increment for other
PHY Types.
EPON MIB WG Expires October 2004 [Page 27]
Internet-Draft EPON MIBs April 29, 2004
Increment the counter by one for each FEC block that is determined to
be uncorrectable by the FEC
function in the PHY."
REFERENCE "[802.3ah], 30.5.1.1.16."
::= { dot3EponMauEntry 5}
dot3EponMauBufferHeadCodingViolation OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" For 1000 Mbps operation it is a counts of the number of invalid code-
group received directly from the link."
::= { dot3EponMauEntry 6}
-- Defining EPON MAU types
--This section should be added to 802.3 MAU MIB RFC.
dot3EponMauType OBJECT IDENTIFIER ::= { dot3EponMauMIB 3 }
eponMauType1000BasePXOLT OBJECT-IDENTITY
STATUS current
DESCRIPTION "Multipoint MAC Control (per 802.3 section
64,65) OLT (master), unknown PMD"
REFERENCE "[802.3ah], 30.5.1.1.2."
::= { dot3EponMauType 1 }
eponMauType1000BasePXONU OBJECT-IDENTITY
STATUS current
DESCRIPTION "Multipoint MAC Control (per 802.3 section
64,65),ONU (slave), unknown PMD"
REFERENCE "[802.3ah], 30.5.1.1.2."
::= { dot3EponMauType 2 }
eponMauType1000BasePX10DOLT OBJECT-IDENTITY
STATUS current
DESCRIPTION "EPON over 10K link, downlink (per 802.3 section
60), OLT side"
REFERENCE "[802.3ah], 30.5.1.1.2."
::= { dot3EponMauType 3 }
eponMauType1000BasePX10DONU OBJECT-IDENTITY
STATUS current
DESCRIPTION "EPON over 10K link, downlink (per 802.3 section
60), ONU side"
EPON MIB WG Expires October 2004 [Page 28]
Internet-Draft EPON MIBs April 29, 2004
REFERENCE "[802.3ah], 30.5.1.1.2."
::= { dot3EponMauType 4 }
eponMauType1000BasePX10UOLT OBJECT-IDENTITY
STATUS current
DESCRIPTION "EPON over 10K link, uplink (per 802.3 section
60), OLT side"
REFERENCE "[802.3ah], 30.5.1.1.2."
::= { dot3EponMauType 5 }
eponMauType1000BasePX10UONU OBJECT-IDENTITY
STATUS current
DESCRIPTION "EPON over 10K link, uplink (per 802.3 section
60), ONU side"
REFERENCE "[802.3ah], 30.5.1.1.2."
::= { dot3EponMauType 6 }
eponMauType1000BasePX20DOLT OBJECT-IDENTITY
STATUS current
DESCRIPTION "EPON over 20K link, downlink (per 802.3 section
60), OLT side"
REFERENCE "[802.3ah], 30.5.1.1.2."
::= { dot3EponMauType 7 }
eponMauType1000BasePX20DONU OBJECT-IDENTITY
STATUS current
DESCRIPTION "EPON over 20K link, downlink (per 802.3 section
60), ONU side"
REFERENCE "[802.3ah], 30.5.1.1.2."
::= { dot3EponMauType 8 }
eponMauType1000BasePX20UOLT OBJECT-IDENTITY
STATUS current
DESCRIPTION "EPON over 20K link, uplink (per 802.3 section
60), OLT side"
REFERENCE "[802.3ah], 30.5.1.1.2."
::= { dot3EponMauType 9 }
eponMauType1000BasePX20UONU OBJECT-IDENTITY
STATUS current
DESCRIPTION "EPON over 20K link, uplink (per 802.3 section
60), ONU side"
EPON MIB WG Expires October 2004 [Page 29]
Internet-Draft EPON MIBs April 29, 2004
REFERENCE "[802.3ah], 30.5.1.1.2."
::= { dot3EponMauType 10 }
-- Conformance Statements
-- Conformance Groups
dot3EponMauGroups OBJECT IDENTIFIER ::={ dot3EponMauConformance 1}
dot3EponMauGroupAll OBJECT-GROUP
OBJECTS {
dot3EponMauPCSCodingViolation
}
STATUS current
DESCRIPTION
"A collection of objects of dot3 MAU definition."
::= { dot3EponMauGroups 1 }
dot3EponMauGroupFEC OBJECT-GROUP
OBJECTS {
dot3EponMauFecAbility,
dot3EponMauFecMode,
dot3EponMauFECCorrectedBlocks,
dot3EponMauFECUncorrectableBlocks,
dot3EponMauBufferHeadCodingViolation
}
STATUS current
DESCRIPTION
"A collection of objects of FEC group definition."
::= { dot3EponMauGroups 2 }
-- Compliance
dot3EponMauCompliances OBJECT IDENTIFIER ::= {dot3EponMauConformance 2}
dot3EponMauCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION "The compliance statement for MAU EPON
interfaces."
MODULE -- this module
MANDATORY-GROUPS { dot3EponMauGroupAll }
GROUP dot3EponMauGroupFEC
EPON MIB WG Expires October 2004 [Page 30]
Internet-Draft EPON MIBs April 29, 2004
DESCRIPTION " This group is mandatory for all
EPON MAU devices Supporting FEC
functionality as for Definitions and BER
Statistics collection."
::= { dot3EponMauCompliances 1}
END
EPON MIB WG Expires October 2004 [Page 31]
Internet-Draft EPON MIBs April 29, 2004
5. Relationship table of the dot3EFM MIB objects to the IEEE802.3ah
objects
oMPCP managed object class (30.3.5)
dot3EFM MIB object IEEE802.3ah object Reference
dot3MpcpID aMPCPID 30.3.5.1.1
dot3MpcpAdminState aMPCPAdminState 30.3.5.1.2
dot3MpcpMode aMPCPMode 30.3.5.1.3
dot3MpcpLinkID aMPCPLinkID 30.3.5.1.4
dot3MpcpRemoteMACAddress aMPCPRemoteMACAddress 30.3.5.1.5
dot3MpcpRegistrationState aMPCPRegistrationState 30.3.5.1.6
dot3MpcpMACCtrlFramesTransmitted aMPCPMACCtrlFramesTransmitted30.3.5.1.7
dot3MpcpMACCtrlFramesReceived aMPCPMACCtrlFramesReceived 30.3.5.1.8
dot3MpcpTxGate aMPCPTxGate 30.3.5.1.9
dot3MpcpTxRegAck aMPCPTxRegAck 30.3.5.1.10
dot3MpcpTxRegister aMPCPTxRegister 30.3.5.1.11
dot3MpcpTxRegRequest aMPCPTxRegRequest 30.3.5.1.12
dot3MpcpTxReport aMPCPTxReport 30.3.5.1.13
dot3MpcpRxGate aMPCPRxGate 30.3.5.1.14
dot3MpcpRxRegAck aMPCPRxRegAck 30.3.5.1.15
dot3MpcpRxRegister aMPCPRxRegister 30.3.5.1.16
dot3MpcpRxRegRequest aMPCPRxRegRequest 30.3.5.1.17
dot3MpcpRxReport aMPCPRxReport 30.3.5.1.18
dot3MpcpTransmitElapsed aMPCPTransmitElapsed 30.3.5.1.19
dot3MpcpReceiveElapsed aMPCPReceiveElapsed 30.3.5.1.20
dot3MpcpRoundTripTime aMPCPRoundTripTime 30.3.5.1.21
dot3MpcpDiscoveryWindowsSent aMPCPDiscoveryWindowsSent 30.3.5.1.22
dot3MpcpDiscoveryTimeout aMPCPDiscoveryTimeout 30.3.5.1.23
dot3MpcpMaximumPendingGrants aMPCPMaximumPendingGrants 30.3.5.1.24
dot3MPCPAdminControl acMPCPAdminControl 30.3.5.2.1
dot3MpcpOnTime laserOnTime 64.3.5.1
dot3MpcpOffTime laserOffTime 64.3.5.1
dot3MpcpSyncTime SyncTime 64.3.3.2
dot3MpcpRxNotSupportedMPCP
oOMPEmulation managed object class (30.3.7)
dot3EFM MIB object IEEE802.3ah object Reference
dot3OmpEmulationID aOMPEmulationID 30.3.7.1.1
dot3OmpEmulationType aOMPEmulationType 30.3.7.1.2
dot3OmpEmulationSLDErrors aSLDErrors 30.3.7.1.3
dot3OmpEmulationCRC8Errors aCRC8Errors 30.3.7.1.4
EPON MIB WG Expires October 2004 [Page 32]
Internet-Draft EPON MIBs April 29, 2004
dot3OmpEmulationGoodLLID aGoodLLID 30.3.7.1.5
dot3OmpEmulationOnuPonCastLLID aONUPONcastLLID 30.3.7.1.6
dot3OmpEmulationOltPonCastLLID aOLTPONcastLLID 30.3.7.1.7
dot3OmpEmulationBadLLID aBadLLID 30.3.7.1.8
dot3OmpEmulationBroadcastLLIDNotOnuID
dot3OmpEmulationOnuLLIDNotBroadcast
dot3OmpEmulationBroadcastLLIDPlusOnuId
dot3OmpEmulationNotBroadcastLLIDNotOnuId
oMAU managed object class (30.5.1)
dot3EFM MIB object IEEE802.3ah object Reference
dot3EponMauType aMAUType 30.5.1.1.2
dot3EponMauPCSCodingViolation aPCSCodingViolation 30.5.1.1.12
dot3EponMauFecAbility aFECAbility 30.5.1.1.13
dot3EponMauFecMode aFECmode 30.5.1.1.14
dot3EponMauFECCorrectedBlocks aFECCorrectedBlocks 30.5.1.1.15
dot3EponMauFECUncorrectableBlocks aFECUncorrectableBlocks 30.5.1.1.16
dot3EponMauBufferHeadCodingViolation
EPON MIB WG Expires October 2004 [Page 33]
Internet-Draft EPON MIBs April 29, 2004
6. Definitions - The EPON Device MIB
EPON-DEVICE-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, mib-2, OBJECT-TYPE, Counter32,
Unsigned32, Integer32, zeroDotZero
FROM SNMPv2-SMI
TruthValue, DateAndTime, RowStatus, MacAddress
FROM SNMPv2-TC
ifIndex
FROM IF-MIB
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
;
eponDeviceMIB MODULE-IDENTITY
LAST-UPDATED "200404290000Z" -- April 29, 2004
ORGANIZATION "IETF Ethernet Interfaces and Hub MIB
Working Group"
CONTACT-INFO
"WG charter:
http://www.ietf.org/html.charters/hubmib-charter.html
Mailing Lists:
General Discussion: hubmib@ietf.org
To Subscribe: hubmib-request@ietf.org
In Body: subscribe your_email_address
Chair: Dan Romascanu
Postal: Avaya Inc.
Atidim Technology Park, Bldg. 3
Tel Aviv 61131
Israel
Tel: +972-3-645-8414
E-mail: dromasca@avaya.com
Editor: Lior Khermosh
Postal: Passave Technologies Inc.
Ackerstein Towers, Tower A, 6th floor,
9 Hamenofim St.
Hertzliya Pituach 46725,
ISRAEL
P.O.Box 2089 Hertzliya Pituach 46120 Israel
EPON MIB WG Expires October 2004 [Page 34]
Internet-Draft EPON MIBs April 29, 2004
Tel: +972-9-9717600 Ext: 7181
E-mail: lior.khermosh@passave.com"
DESCRIPTION
"The objects in this MIB module are used to manage Ethernet
Passive Optical Network (EPON) devices which are based on the
Ethernet in the First Mile (EFM) PON as defined in IEEE Draft
P802.3ah/D3.0 clause 60,64,65.
The following reference is used throughout this MIB module:
[802.3ah] refers to:
IEEE Draft P802.3ah/D3.3: 'Draft amendment to -
Information technology - Telecommunications and
information exchange between systems - Local and
metropolitan area networks - Specific requirements -
Part 3: Carrier sense multiple access with collision
detection (CSMA/CD) access method and physical layer
specifications - Media Access Control
Parameters,Physical
Layers and Management Parameters for subscriber access
networks', 22 April 2004.
Of particular interest are Clause 64(MPCP) 65(P2mP RS) and
60 (PON PMDs). Clause 30, 'Management', and Clause
45,'Management Data Input/Output (MDIO) Interface'.
Copyright (C) The Internet Society (2003). This version
of this MIB module is part of XXXX see the RFC
itself for full legal notices."
-- Editor's Note: Replace XXXX with the actual RFC number
-- assigned by RFC Editor and remove this note
REVISION "200404290000Z" -- April 29, 2004
DESCRIPTION "Initial version, published as RFC XXXX."
::= { mib-2 XXX }
-- Editor's Note: Replace XXX with a real OID once it is
-- assigned by IANA and remove this note.
eponDeviceObjectMIB OBJECT IDENTIFIER ::= { eponDeviceMIB 1}
eponDeviceObjects OBJECT IDENTIFIER ::= { eponDeviceObjectMIB 1}
eponDeviceConformance OBJECT IDENTIFIER ::= { eponDeviceObjectMIB 2 }
EPON MIB WG Expires October 2004 [Page 35]
Internet-Draft EPON MIBs April 29, 2004
eponDeviceControlObjects OBJECT IDENTIFIER ::= { eponDeviceObjects 1}
eponDeviceStatObjects OBJECT IDENTIFIER ::= { eponDeviceObjects 2}
eponDeviceEventObjects OBJECT IDENTIFIER ::= { eponDeviceObjects 3}
eponDeviceControlTable OBJECT-TYPE
SYNTAX SEQUENCE OF EponDeviceControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table for EPON device MIBs."
::= { eponDeviceControlObjects 1 }
eponDeviceControlEntry OBJECT-TYPE
SYNTAX EponDeviceControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the EPON device Control table."
INDEX { ifIndex }
::= { eponDeviceControlTable 1 }
EponDeviceControlEntry ::=
SEQUENCE {
eponDeviceObjectReset INTEGER,
eponDeviceObjectModes INTEGER,
eponDeviceSerialNumber SnmpAdminString,
eponDeviceObjectFecEnabled INTEGER,
eponDeviceObjectOamMode INTEGER,
eponDeviceObjectDeviceReadyMode INTEGER,
eponDeviceObjectPowerDown TruthValue,
eponDeviceObjectNumberOfLLIDs INTEGER,
eponDeviceObjectRemoteMACAddressLLIDTable MacAddress,
eponDeviceObjectReportThreshold Integer32
}
eponDeviceObjectReset OBJECT-TYPE
SYNTAX INTEGER {
running(1),
reset(2)
}
MAX-ACCESS read-write
EPON MIB WG Expires October 2004 [Page 36]
Internet-Draft EPON MIBs April 29, 2004
STATUS current
DESCRIPTION
"This variable can be used to reset the EPON device. The
interface may be unavailable while the reset occurs and data may be
lost."
::= { eponDeviceControlEntry 1 }
eponDeviceObjectModes OBJECT-TYPE
SYNTAX INTEGER {
olt(1),
onu(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable defines the mode of the EPON device. When an
olt it is an Optical Line Terminal device (server) and when an onu and
Optical Network Unit device (client)"
::= { eponDeviceControlEntry 2 }
eponDeviceSerialNumber OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The serial number of the manufacturer for this device."
::= { eponDeviceControlEntry 3 }
eponDeviceObjectFecEnabled OBJECT-TYPE
SYNTAX INTEGER {
noFecEnabled (1),
fecTxEnabled (2),
fecRxEnabled (3),
fecTxRxEnabled (4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable defines whether the EPON device uses FEC as
defined in the [802.3ah] clause 65.2 for EPON. When fecTxEnabled the
device supports the FEC transmission mode. When fecRxEnabled the
device supports the FEC Receive mode. When fecTxRxEnabled the device
supports the FEC transmission and receive mode."
::= { eponDeviceControlEntry 4 }
eponDeviceObjectOamMode OBJECT-TYPE
SYNTAX INTEGER {
noOam (1),
EPON MIB WG Expires October 2004 [Page 37]
Internet-Draft EPON MIBs April 29, 2004
oamServer (2),
oamclient (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable defines the Operation Administration and
Maintenance (OAM) mode of an EPON device as defined by the [802.3ah]
clause 57. When noOam the device does not supports the OAM mode. When
oamServer the device supports the OAM mode as a server unit. When
oamClient the device supports the OAM mode as a client unit."
::= { eponDeviceControlEntry 5 }
eponDeviceObjectDeviceReadyMode OBJECT-TYPE
SYNTAX INTEGER {
notReady (1),
inProcess (2),
ready (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable defines the mode of an EPON device in
initialization û ready for registration as defined by the [802.3ah]
clause 64. When notReady the device is not ready for operation. When
inProcess the device is in initialization process. When ready the
device is ready for registration."
::= { eponDeviceControlEntry 6 }
eponDeviceObjectPowerDown OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting this variable to powerDown will cause Device to be
entered into Power down mode where no registration is allowed and only
receiving data from the link"
::= { eponDeviceControlEntry 7 }
eponDeviceObjectNumberOfLLIDs OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-Only
EPON MIB WG Expires October 2004 [Page 38]
Internet-Draft EPON MIBs April 29, 2004
STATUS current
DESCRIPTION
"A read only variable which defines the number of registered
LLIDs (as defined by the [802.3ah] clause 65) in a EPON network for an
OLT. Initialization value is 0."
::= { eponDeviceControlEntry 8 }
eponDeviceObjectReportThreshold OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A set of 8 integers, for each LLID, that defines the threshold
reporting for each Queue in the REPORT message, as defined in
[802.3ah] 64. The value returned shall be in 2 octets increaments."
::= { eponDeviceControlEntry 9 }
eponDeviceRemoteMACAddressLLIDTable OBJECT-TYPE
SYNTAX SEQUENCE OF EponDeviceRemoteMACAddressLLIDEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table of read-only value that identifies the
source_address and LLIDs parameter of the remote devices in the
network. This Macaddress value, as defined in [802.3ah], 30.3.5.1.5,
is updated on reception of a valid frame with (1) a destination Field
equal to the reserved multicast address for MAC Control specified in
[802.3ah] Annex 31A, (2) lengthOrType field value equal to the
reserved Type for MAC Control as specified in [802.3ah] Annex 31A. (3)
an MPCP subtype value equal to the subtype reserved for MPCP as
specified in [802.3ah] Annex 31A, and an LLID as allocated by the OLT.
The table is defined as Remote MAC address û LLID (RMadL)"
::= { eponDeviceControlObjects 2 }
eponDeviceRemoteMACAddressLLIDEntry OBJECT-TYPE
SYNTAX EponDeviceRemoteMACAddressLLIDEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A group of entries. Applications create and delete entries
using eponDeviceRMadlEntryStatus.
When adding objects to a notification they are added in the
lexical order of their index in this table."
INDEX {eponDeviceRMadlLogName, eponDeviceRMadlLLID }
::= { eponDeviceRemoteMACAddressLLIDTable 1 }
EponDeviceRemoteMACAddressLLIDEntry ::= SEQUENCE {
eponDeviceRMadlLogName SnmpAdminString,
EPON MIB WG Expires October 2004 [Page 39]
Internet-Draft EPON MIBs April 29, 2004
eponDeviceRMadlLLID Unsigned32,
eponDeviceRMadlLogID OBJECT IDENTIFIER,
eponDeviceRMadlRemoteMACAddress MacAddress,
eponDeviceRMadlType INTEGER,
eponDeviceRMadlAction INTEGER,
eponDeviceRMadlEntryStatus RowStatus
}
eponDeviceRMadlLogName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A locally-unique, administratively assigned name for a group
of entries."
::= { eponDeviceRemoteMACAddressLLIDEntry 1 }
eponDeviceRMadlLLID OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"An arbitrary integer for the purpose of identifying
the LLID."
::= { eponDeviceRemoteMACAddressLLIDEntry 2 }
eponDeviceRMadlLogID OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The object identifier of a MIB object to add to an entry."
DEFVAL { zeroDotZero }
::= { eponDeviceRemoteMACAddressLLIDEntry 3 }
eponDeviceRMadlRemoteMacAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The remote MAC address of the LLID."
::= { eponDeviceRemoteMACAddressLLIDEntry 4 }
eponDeviceRMadlType OBJECT-TYPE
SYNTAX INTEGER {
EPON MIB WG Expires October 2004 [Page 40]
Internet-Draft EPON MIBs April 29, 2004
registered (1),
notRegister (2),
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A list of types for entries."
::= { eponDeviceRemoteMACAddressLLIDEntry 5 }
eponDeviceRMadlAction OBJECT-TYPE
SYNTAX INTEGER {
register (1),
deregister (2),
reregister (3
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A list of actions for an entry."
::= { eponDeviceRemoteMACAddressLLIDEntry 6 }
eponDeviceRMadlEntryStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The control that allows creation and deletion of entries.
Once made active an entry MAY not be modified except to
delete it."
::= { eponDeviceRemoteMACAddressLLIDEntry 7 }
--Statistics tables
eponDeviceStatTable OBJECT-TYPE
SYNTAX SEQUENCE OF EponDeviceStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table defines the list of statistics counters of EPON devices."
::= { eponDeviceStatObjects 1}
EPON MIB WG Expires October 2004 [Page 41]
Internet-Draft EPON MIBs April 29, 2004
eponDeviceStatEntry OBJECT-TYPE
SYNTAX EponDeviceStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table entries for Table of statistics counters of EPON devices."
INDEX { ifIndex }
::= { eponDeviceStatTable 1 }
EponDeviceStatEntry::=
SEQUENCE {
eponDeviceStatTxFramesQueue0 Counter32,
eponDeviceStatTxFramesQueue1 Counter32,
eponDeviceStatTxFramesQueue2 Counter32,
eponDeviceStatTxFramesQueue3 Counter32,
eponDeviceStatTxFramesQueue4 Counter32,
eponDeviceStatTxFramesQueue5 Counter32,
eponDeviceStatTxFramesQueue6 Counter32,
eponDeviceStatTxFramesQueue7 Counter32,
eponDeviceStatRxFramesQueue0 Counter32,
eponDeviceStatRxFramesQueue1 Counter32,
eponDeviceStatRxFramesQueue2 Counter32,
eponDeviceStatRxFramesQueue3 Counter32,
eponDeviceStatRxFramesQueue4 Counter32,
eponDeviceStatRxFramesQueue5 Counter32,
eponDeviceStatRxFramesQueue6 Counter32,
eponDeviceStatRxFramesQueue7 Counter32,
eponDeviceStatDroppedFramesQueue0 Counter32,
eponDeviceStatDroppedFramesQueue1 Counter32,
eponDeviceStatDroppedFramesQueue2 Counter32,
eponDeviceStatDroppedFramesQueue3 Counter32,
eponDeviceStatDroppedFramesQueue4 Counter32,
eponDeviceStatDroppedFramesQueue5 Counter32,
eponDeviceStatDroppedFramesQueue6 Counter32,
eponDeviceStatDroppedFramesQueue7 Counter32
}
eponDeviceStatTxFramesQueue0 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-0Æ frames transmission
occurs. Increment the counter by one for each frame transmitted which
is an
output of æQueue-0Æ. The æQueue-0Æ marking matched the REPORT MPCP
message Queue-0 field, as defined in [802.3ah] clause 64. This
counter
EPON MIB WG Expires October 2004 [Page 42]
Internet-Draft EPON MIBs April 29, 2004
is mandatory for an ONU."
::= { eponDeviceStatEntry 1}
eponDeviceStatTxFramesQueue1 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-1Æ frames transmission
occurs. Increment the counter by one for each frame transmitted which
is an output of æQueue-1Æ. The æQueue-1Æ marking matched the REPORT
MPCP message Queue-1 field, as defined in [802.3ah] clause 64. This
counter is mandatory for an ONU."
::= { eponDeviceStatEntry 2}
eponDeviceStatTxFramesQueue2 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-2Æ frames transmission
occurs. Increment the counter by one for each frame transmitted which
is an output of æQueue-2Æ. The æQueue-2Æ marking matched the REPORT
MPCP message Queue-2 field, as defined in [802.3ah] clause 64. This
counter is mandatory for an ONU."
::= { eponDeviceStatEntry 3}
eponDeviceStatTxFramesQueue3 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-3Æ frames transmission
occurs. Increment the counter by one for each frame transmitted which
is an output of æQueue-3Æ. The æQueue-3Æ marking matched the REPORT
MPCP message Queue-3 field, as defined in [802.3ah] clause 64. This
counter is mandatory for an ONU."
::= { eponDeviceStatEntry 4}
eponDeviceStatTxFramesQueue4 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-4Æ frames transmission
occurs. Increment the counter by one for each frame transmitted which
is an
output of æQueue-4Æ. The æQueue-4Æ marking matched the REPORT MPCP
EPON MIB WG Expires October 2004 [Page 43]
Internet-Draft EPON MIBs April 29, 2004
message Queue-4 field, as defined in [802.3ah] clause 64. This counter
is mandatory for an ONU."
::= { eponDeviceStatEntry 5}
eponDeviceStatTxFramesQueue5 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-5Æ frames transmission
occurs. Increment the counter by one for each frame transmitted which
is an output of æQueue-5Æ. The æQueue-5Æ marking matched the REPORT
MPCP message Queue-5 field, as defined in [802.3ah] clause 64. This
counter is mandatory for an ONU."
::= { eponDeviceStatEntry 6}
eponDeviceStatTxFramesQueue6 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-6Æ frames transmission
occurs. Increment the counter by one for each frame transmitted which
is an output
of æQueue-6Æ. The æQueue-6Æ marking matched the REPORT MPCP message
Queue-6 field, as defined in [802.3ah] clause 64. This counter is
mandatory for an ONU."
::= { eponDeviceStatEntry 7}
eponDeviceStatTxFramesQueue7 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-7Æ frames transmission
occurs. Increment the counter by one for each frame transmitted which
is an output of æQueue-7Æ. The æQueue-7Æ marking matched the REPORT
MPCP message Queue-0 field, as defined in [802.3ah] clause 64. This
counter is mandatory for an ONU."
::= { eponDeviceStatEntry 8}
eponDeviceStatRxFramesQueue0 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-0Æ frames reception occurs.
A
EPON MIB WG Expires October 2004 [Page 44]
Internet-Draft EPON MIBs April 29, 2004
single counter at the ONU and a set of counters, one for each LLID, at
the OLT. Increment the counter by one for each frame received for each
LLID, which is an output of æQueue-0Æ. The æQueue-0Æ marking matched
the REPORT MPCP message Queue-0 field, as defined in [802.3ah] clause
64. This counter is mandatory for an ONU and an OLT."
::= { eponDeviceStatEntry 9}
eponDeviceStatRxFramesQueue1 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the number of times a æQueue-1Æ frames reception occurs. A
single counter at the ONU and a set of counters, one for each LLID, at
the OLT. Increment the counter by one for each frame received for each
LLID, which is an output of æQueue-1Æ. The æQueue-1Æ marking matched
the REPORT MPCP message Queue-1 field, as defined in [802.3ah] clause
64. This counter is mandatory for an ONU and an OLT."
::= { eponDeviceStatEntry 10}
eponDeviceStatRxFramesQueue2 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-2Æ frames reception occurs.
A single counter at the ONU and a set of counters, one for each LLID,
at the OLT. Increment the counter by one for each frame received for
each LLID, which is an output of æQueue-2Æ. The æQueue-2Æ marking
matched the REPORT MPCP message Queue-2 field, as defined in [802.3ah]
clause 64. This counter is mandatory for an ONU and an OLT."
::= { eponDeviceStatEntry 11}
eponDeviceStatRxFramesQueue3 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-3Æ frames reception occurs.
A single counter at the ONU and a set of counters, one for each LLID,
at the OLT. Increment the counter by one for each frame received for
each LLID, which is an output of æQueue-3Æ. The æQueue-3Æ marking
matched the
REPORT MPCP message Queue-3 field, as defined in [802.3ah] clause 64.
This counter is mandatory for an ONU and an OLT."
::= { eponDeviceStatEntry 12}
eponDeviceStatRxFramesQueue4 OBJECT-TYPE
EPON MIB WG Expires October 2004 [Page 45]
Internet-Draft EPON MIBs April 29, 2004
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the number of times a æQueue-4Æ frames reception occurs. A
single counter at the ONU and a set of counters, one for each LLID, at
the OLT. Increment the counter by one for each frame received for each
LLID, which is an output of æQueue-4Æ. The æQueue-4Æ marking matched
the REPORT MPCP message Queue-4 field, as defined in [802.3ah] clause
64. This counter is mandatory for an ONU and an OLT."
::= { eponDeviceStatEntry 13}
eponDeviceStatRxFramesQueue5 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-5Æ frames reception occurs.
A single counter at the ONU and a set of counters, one for each LLID,
at the OLT. Increment the counter by one for each frame received for
each LLID, which is an output of æQueue-5Æ. The æQueue-5Æ marking
matched the REPORT MPCP message Queue-5 field, as defined in [802.3ah]
clause 64. This counter is mandatory for an ONU and an OLT."
::= { eponDeviceStatEntry 14}
eponDeviceStatRxFramesQueue6 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-6Æ frames reception occurs.
A single counter at the ONU and a set of counters, one for each LLID,
at the OLT. Increment the counter by one for each frame received for
each LLID, which is an output of æQueue-6Æ. The æQueue-6Æ marking
matched the REPORT MPCP message Queue-6 field, as defined in [802.3ah]
clause 64. This counter is mandatory for an ONU and an OLT."
::= { eponDeviceStatEntry 15}
eponDeviceStatRxFramesQueue7 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-7Æ frames reception occurs.
A single counter at the ONU and a set of counters, one for each LLID,
at the OLT. Increment the counter by one for each frame received for
each LLID, which is an output of æQueue-7Æ. The æQueue-7Æ marking
matched the
EPON MIB WG Expires October 2004 [Page 46]
Internet-Draft EPON MIBs April 29, 2004
REPORT MPCP message Queue-7 field, as defined in [802.3ah] clause 64.
This counter is mandatory for an ONU and an OLT."
::= { eponDeviceStatEntry 16}
eponDeviceStatDroppedFramesQueue0 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-0Æ frames drops occurs.
Increment the counter by one for each frame dropped from æQueue-0Æ.
The æQueue-0Æ marking matched the REPORT MPCP message Queue-0 field,
as defined in [802.3ah] clause 64. This counter is mandatory for an
ONU."
::= { eponDeviceStatEntry 17}
eponDeviceStatDroppedFramesQueue1 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-1Æ frames drops occurs.
Increment the counter by one for each frame dropped from æQueue-1Æ.
The æQueue-1Æ marking matched the REPORT MPCP message Queue-1 field,
as defined in [802.3ah] clause 64. This counter is mandatory for an
ONU."
::= { eponDeviceStatEntry 18}
eponDeviceStatDroppedFramesQueue2 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-2Æ frames drops occurs.
Increment the counter by one for each frame dropped from æQueue-2Æ.
The æQueue-2Æ marking matched the REPORT MPCP message Queue-2 field,
as defined in [802.3ah] clause 64. This counter is mandatory for an
ONU."
::= { eponDeviceStatEntry 19}
eponDeviceStatDroppedFramesQueue3 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-3Æ frames drops occurs.
Increment the counter by one for each frame dropped from æQueue-3Æ.
The æQueue-3Æ marking matched the REPORT MPCP message Queue-3 field,
as defined in [802.3ah] clause 64. This counter is mandatory for an
ONU."
::= { eponDeviceStatEntry 20}
EPON MIB WG Expires October 2004 [Page 47]
Internet-Draft EPON MIBs April 29, 2004
eponDeviceStatDroppedFramesQueue4 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-4Æ frames drops occurs.
Increment the counter by one for each frame dropped from æQueue-4Æ.
The æQueue-4Æ marking matched the REPORT MPCP message Queue-4 field,
as defined in [802.3ah] clause 64. This counter is mandatory for an
ONU."
::= { eponDeviceStatEntry 21}
eponDeviceStatDroppedFramesQueue5 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-5Æ frames drops occurs.
Increment the counter by one for each frame dropped from æQueue-5Æ.
The æQueue-5Æ marking matched the REPORT MPCP message Queue-5 field,
as defined in [802.3ah] clause 64. This counter is mandatory for an
ONU."
::= { eponDeviceStatEntry 22}
eponDeviceStatDroppedFramesQueue6 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-6Æ frames drops occurs.
Increment the counter by one for each frame dropped from æQueue-6Æ.
The æQueue-6Æ marking matched the REPORT MPCP message Queue-6 field,
as defined in [802.3ah] clause 64. This counter is mandatory for an
ONU."
::= { eponDeviceStatEntry 23}
eponDeviceStatDroppedFramesQueue7 OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" A count of the number of times a æQueue-7Æ frames drops occurs.
Increment the counter by one for each frame dropped from æQueue-7Æ.
The æQueue-7Æ marking matched the REPORT MPCP message Queue-7 field,
as defined in [802.3ah] clause 64. This counter is mandatory for an
ONU."
::= { eponDeviceStatEntry 24}
EPON MIB WG Expires October 2004 [Page 48]
Internet-Draft EPON MIBs April 29, 2004
--Editor's Note use reference to event MIBs [RFC2981] and
--docsis MIBs [RFC2669]
eponDeviceEventObjectTable OBJECT-TYPE
SYNTAX SEQUENCE OF EponDeviceEventObjectEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table defines the list of statistics counters of EPON devices."
::= { eponDeviceEventObjects 1}
eponDeviceEventObjectEntry OBJECT-TYPE
SYNTAX EponDeviceEventObjectEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table entries for Table of Event objects for EPON devices."
INDEX { ifIndex }
::= { eponDeviceEventObjectTable 1 }
EponDeviceEventObjectEntry::=
SEQUENCE {
eponDeviceSampleMinimum Integer32,
eponDeviceDyingGaspAlarmState TruthValue,
eponDeviceDyingGaspAlarmEnabled TruthValue,
eponDeviceCriticalEventState TruthValue,
eponDeviceCriticalEventEnabled TruthValue,
eponDeviceLocalLinkFaultAlarmState TruthValue,
eponDeviceLocalLinkFaultAlarmEnabled TruthValue,
eponDeviceTemperatureEventIndicationState TruthValue,
eponDeviceTemperatureEventIndicationEnabled TruthValue,
eponDevicePowerVoltageEventIndicationState TruthValue,
eponDevicePowerVoltageEventIndicationEnabled TruthValue,
eponDeviceGlobalEventState TruthValue,
eponDeviceGlobalEventEnabled TruthValue,
eponDeviceErroredSymbolPeriodEventState TruthValue,
eponDeviceErroredSymbolPeriodEventEnabled TruthValue,
eponDeviceErroredFrameEventState TruthValue,
eponDeviceErroredFrameEventEnabled TruthValue,
eponDeviceErroredFramePeriodEventState TruthValue,
eponDeviceErroredFramePeriodEventEnabled TruthValue,
eponDeviceErroredFrameSecondsSummaryEventState TruthValue,
eponDeviceErroredFrameSecondsSummaryEventEnabled TruthValue,
eponDeviceOrganizationSpecificEventState TruthValue,
EPON MIB WG Expires October 2004 [Page 49]
Internet-Draft EPON MIBs April 29, 2004
eponDeviceOrganizationSpecificEventEnabled TruthValue,
eponDeviceEventControl INTEGER
}
eponDeviceSampleMinimum OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The minimum Frequency of events this system will
accept. A system may use the larger values of this minimum to
lessen the impact of constant sampling. For larger
sampling intervals the system samples less often and
suffers less overhead.
Unless explicitly resource limited, a system's value for
this object SHOULD be 1, allowing as small as a 1 second
interval for ongoing trigger sampling."
::= { eponDeviceEventObjectEntry 1 }
eponDeviceDyingGaspAlarmState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only variable, which defines the state of the Dying
Gasp indication of the OAM alarm indications as described in the
[802.3ah] clause 57. When dyingGaspAlarm the device has a dying gasp
alarm asserted. When the dyingGaspAlarm state is removed the dying
gasp alarm is reset "
::= { eponDeviceEventObjectEntry 2}
eponDeviceDyingGaspAlarmEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A control to allow DyingGaspAlarm event to be used.
When the value is 'false' the event is not sampled."
EPON MIB WG Expires October 2004 [Page 50]
Internet-Draft EPON MIBs April 29, 2004
DEFVAL { false }
::= { eponDeviceEventObjectEntry 3 }
eponDeviceCriticalEventState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only variable, which defines the state of the
Critical Event indication of the OAM alarm indications as described in
the [802.3ah] clause 57. When criticalEvent the device has a Critical
Event asserted. "
::= { eponDeviceEventObjectEntry 4 }
eponDeviceCriticalEventEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A control to allow CriticalEvent event to be used.
When the value is 'false' the event is not sampled."
DEFVAL { false }
::= { eponDeviceEventObjectEntry 5 }
eponDeviceLocalLinkFaultAlarmState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only variable, which defines the state of the Local
Link Fault indication of the OAM alarm indications as described in the
[802.3ah] clause 57. When localLinkFaultAlarm the device has a Local
Link Fault alarm asserted. "
::= { eponDeviceEventObjectEntry 6 }
eponDeviceLocalLinkFaultAlarmEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A control to allow LocalLinkFaultAlarm event to be used.
When the value is 'false' the event is not sampled."
DEFVAL { false }
::= { eponDeviceEventObjectEntry 7 }
eponDeviceTemperatureEventIndicationState OBJECT-TYPE
EPON MIB WG Expires October 2004 [Page 51]
Internet-Draft EPON MIBs April 29, 2004
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only variable, which defines the state of the
Temperature Event indication of an EPON device. When condition of box
temperature is above the threshold defined the alarm is asserted. When
the condition is below that threshold the alarm is de-asserted. When
temperatureEventIndication the device has a Temperature Event
Indication asserted. "
::= { eponDeviceEventObjectEntry 8 }
eponDeviceTemperatureEventIndicationEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A control to allow TemperatureEventIndication event to be
used.
When the value is 'false' the event is not sampled."
DEFVAL { false }
::= { eponDeviceEventObjectEntry 9 }
eponDevicePowerVoltageEventIndicationState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only variable, which defines the state of the
Power/Voltage Event Indication of an EPON device. When condition of
box Power/voltage is above the threshold defined the alarm is
asserted. When the condition is below that threshold the alarm is de-
asserted. When powerVoltageEventIndication the device has a
Power/Voltage Event Indication asserted. "
::= { eponDeviceEventObjectEntry 10 }
eponDevicePowerVoltageEventIndicationEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A control to allow PowerVoltageEventIndication event to be
used.
When the value is 'false' the event is not sampled."
EPON MIB WG Expires October 2004 [Page 52]
Internet-Draft EPON MIBs April 29, 2004
DEFVAL { false }
::= { eponDeviceEventObjectEntry 11 }
eponDeviceGlobalEventState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only variable, which defines the state of the Global Event
indication of an EPON device. When the indication of the event input
occurs the event is asserted. When the input is removed that event is
de-asserted. When globalEvent the device has a Global Event asserted.
"
::= { eponDeviceEventObjectEntry 12 }
eponDeviceGlobalEventEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A control to allow GlobalEvent event to be used.
When the value is 'false' the event is not sampled."
DEFVAL { false }
::= { eponDeviceEventObjectEntry 13 }
eponDeviceErroredSymbolPeriodEventState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only variable, which defines the state of the Errored Symbol
Period Event indication of the OAM alarm TLV indications as described
in the [802.3ah] clause 57.5.3. When erroredSymbolPeriodEvent the
device has an Errored Symbol Period Event asserted. "
::= { eponDeviceEventObjectEntry 14}
eponDeviceErroredSymbolPeriodEventEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A control to allow ErroredSymbolPeriodEvent event to be used.
When the value is 'false' the event is not sampled."
DEFVAL { false }
::= { eponDeviceEventObjectEntry 15 }
EPON MIB WG Expires October 2004 [Page 53]
Internet-Draft EPON MIBs April 29, 2004
eponDeviceErroredFrameEventState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only variable, which defines the state of the Errored Frame
Event indication of the OAM alarm TLV indications as described in the
[802.3ah] clause 57.5.3. When erroredFrameEvent the device has an
Errored Frame Event asserted. "
::= { eponDeviceEventObjectEntry 16 }
eponDeviceErroredFrameEventEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A control to allow ErroredFrameEvent event to be used.
When the value is 'false' the event is not sampled."
DEFVAL { false }
::= { eponDeviceEventObjectEntry 17 }
eponDeviceErroredFramePeriodEventState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only variable, which defines the state of the Errored Frame
Period Event indication of the OAM alarm TLV indications as described
in
the [802.3ah] clause 57.5.3. When erroredFramePeriodEvent the device
has an Errored Frame Period Event asserted. "
::= { eponDeviceEventObjectEntry 18 }
eponDeviceErroredFramePeriodEventEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A control to allow ErroredFramePeriodEvent event to be used.
When the value is 'false' the event is not sampled."
DEFVAL { false }
::= { eponDeviceEventObjectEntry 19 }
eponDeviceErroredFrameSecondsSummaryEventState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
EPON MIB WG Expires October 2004 [Page 54]
Internet-Draft EPON MIBs April 29, 2004
STATUS current
DESCRIPTION
"A read-only variable, which defines the state of the Errored Frame
Seconds Summary Event indication of the OAM alarm TLV indications as
described in the [802.3ah] clause 57.5.3. When
erroredFrameSecondsSummaryEvent the device has an Errored Frame
Seconds Summary Event asserted. "
::= { eponDeviceEventObjectEntry 20 }
eponDeviceErroredFrameSecondsSummaryEventEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A control to allow ErroredFrameSecondsSummaryEvent event to
be used.
When the value is 'false' the event is not sampled."
DEFVAL { false }
::= { eponDeviceEventObjectEntry 21 }
eponDeviceOrganizationSpecificEventState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only variable, which defines the state of the Organization
Specific Event indication of the OAM alarm TLV indications as
described in the [802.3ah] clause 57.5.3. When
organizationSpecificEvent the device has an Organization Specific
Event asserted. "
::= { eponDeviceEventObjectEntry 22 }
eponDeviceOrganizationSpecificEventEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A control to allow OrganizationSpecificEvent event to be
used.
When the value is 'false' the event is not sampled."
DEFVAL { false }
::= { eponDeviceEventObjectEntry 23 }
eponDeviceEventControl OBJECT-TYPE
SYNTAX INTEGER {
EPON MIB WG Expires October 2004 [Page 55]
Internet-Draft EPON MIBs April 29, 2004
resetLog(1),
useDefaultReporting(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting this object to resetLog(1) empties the event log.
All data is deleted. Setting it to useDefaultReporting(2)
returns all event priorities to their factory-default
reporting. Reading this object always returns
useDefaultReporting(2)."
::= { eponDeviceEventObjectEntry 24 }
-- Events Log Table
eponDeviceEventsLogTable OBJECT-TYPE
SYNTAX SEQUENCE OF EponDeviceEventsLogEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of objects that can be added to notifications based
on the event as pointed to by entries in those tables."
::= { eponDeviceEventObjects 2 }
eponDeviceEventsLogEntry OBJECT-TYPE
SYNTAX EponDeviceEventsLogEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A group of Events. Applications create and delete entries
using eponDeviceEventsEntryStatus.
When adding objects to a notification they are added in the
lexical order of their index in this table."
INDEX {eponDeviceEventsLogName, eponDeviceEventsLogIndex }
::= { eponDeviceEventsLogTable 1 }
EponDeviceEventsLogEntry ::= SEQUENCE {
eponDeviceEventsLogName SnmpAdminString,
eponDeviceEventsLogIndex Unsigned32,
eponDeviceEventsLogID OBJECT IDENTIFIER,
eponDeviceEventsLogFirstTime DateAndTime,
eponDeviceEventsLogLastTime DateAndTime,
eponDeviceEventsLogCounts Counter32,
EPON MIB WG Expires October 2004 [Page 56]
Internet-Draft EPON MIBs April 29, 2004
eponDeviceEventsLogType INTEGER,
eponDeviceEventsLogEntryStatus RowStatus
}
eponDeviceEventsLogName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A locally-unique, administratively assigned name for a group
of Events."
::= { eponDeviceEventsLogEntry 1 }
eponDeviceEventsLogIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary integer for the purpose of identifying
individual Events within a eponDeviceEventsLogName group.
Events within a group are placed in the notification in the
numerical order of this index."
::= { eponDeviceEventsLogEntry 2 }
eponDeviceEventsLogID OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The object identifier of a MIB object to add to a
Notification that results from the event."
DEFVAL { zeroDotZero }
::= { eponDeviceEventsLogEntry 3 }
eponDeviceEventsLogFirstTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time that an entry was created."
::= { eponDeviceEventsLogEntry 4 }
eponDeviceEventsLogLastTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If multiple events are reported via the same entry, the
EPON MIB WG Expires October 2004 [Page 57]
Internet-Draft EPON MIBs April 29, 2004
time that the last event for this entry occurred,
otherwise this should have the same value as
eponDeviceEventsLogFirstTime. "
::= { eponDeviceEventsLogEntry 5 }
eponDeviceEventsLogCounts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of consecutive event instances reported by
this entry. This starts at 1 with the creation of this
row and increments by 1 for each subsequent duplicate
event."
::= { eponDeviceEventsLogEntry 6 }
eponDeviceEventsLogType OBJECT-TYPE
SYNTAX INTEGER {
eponDeviceDyingGaspAlarmState (1),
eponDeviceCriticalEventState (2),
eponDeviceLocalLinkFaultAlarmState (3),
eponDeviceTemperatureEventIndicationState (4),
eponDevicePowerVoltageEventIndicationState (5),
eponDeviceGlobalEventState (6),
eponDeviceErroredSymbolPeriodEventState (7),
eponDeviceErroredFrameEventState (8),
eponDeviceErroredFramePeriodEventState (9),
eponDeviceErroredFrameSecondsSummaryEventState (10),
eponDeviceOrganizationSpecificEventState (11)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A list of types for Events."
::= { eponDeviceEventsLogEntry 7 }
eponDeviceEventsLogEntryStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The control that allows creation and deletion of entries.
Once made active an entry MAY not be modified except to
EPON MIB WG Expires October 2004 [Page 58]
Internet-Draft EPON MIBs April 29, 2004
delete it."
::= { eponDeviceEventsLogEntry 8 }
-- Conformance Statements
-- Conformance Groups
eponDeviceGroups OBJECT IDENTIFIER ::={ eponDeviceConformance 1}
eponDeviceGroupControl OBJECT-GROUP
OBJECTS {
eponDeviceObjectReset,
eponDeviceObjectModes,
eponDeviceSerialNumber,
eponDeviceObjectFecEnabled,
eponDeviceObjectOamMode,
eponDeviceObjectDeviceReadyMode,
eponDeviceObjectPowerDown,
eponDeviceObjectNumberOfLLIDs,
eponDeviceObjectRemoteMACAddressLLIDTable,
eponDeviceObjectReportThreshold
}
STATUS current
DESCRIPTION
"A collection of objects of eponDevice control
definition."
::= { eponDeviceGroups 1 }
eponDeviceGroupRMadLTable OBJECT-GROUP
OBJECTS {
eponDeviceRMadlLogName,
eponDeviceRMadlLLID,
eponDeviceRMadlLogID,
eponDeviceRMadlRemoteMACAddress,
eponDeviceRMadlType,
eponDeviceRMadlAction,
eponDeviceRMadlEntryStatus
}
STATUS current
DESCRIPTION
"A collection of objects of eponDevice remote Mac address
EPON MIB WG Expires October 2004 [Page 59]
Internet-Draft EPON MIBs April 29, 2004
to LLID table."
::= { eponDeviceGroups 2 }
eponDeviceGroupStat OBJECT-GROUP
OBJECTS {
eponDeviceStatTxFramesQueue0,
eponDeviceStatTxFramesQueue1,
eponDeviceStatTxFramesQueue2,
eponDeviceStatTxFramesQueue3,
eponDeviceStatTxFramesQueue4,
eponDeviceStatTxFramesQueue5,
eponDeviceStatTxFramesQueue6,
eponDeviceStatTxFramesQueue7,
eponDeviceStatRxFramesQueue0,
eponDeviceStatRxFramesQueue1,
eponDeviceStatRxFramesQueue2,
eponDeviceStatRxFramesQueue3,
eponDeviceStatRxFramesQueue4,
eponDeviceStatRxFramesQueue5,
eponDeviceStatRxFramesQueue6,
eponDeviceStatRxFramesQueue7,
eponDeviceStatDroppedFramesQueue0,
eponDeviceStatDroppedFramesQueue1,
eponDeviceStatDroppedFramesQueue2,
eponDeviceStatDroppedFramesQueue3,
eponDeviceStatDroppedFramesQueue4,
eponDeviceStatDroppedFramesQueue5,
eponDeviceStatDroppedFramesQueue6,
eponDeviceStatDroppedFramesQueue7
}
STATUS current
DESCRIPTION
"A collection of objects of EPON device Statistics"
::= { eponDeviceGroups 3 }
eponDeviceGroupEvent OBJECT-GROUP
OBJECTS {
eponDeviceSampleMinimum,
eponDeviceDyingGaspAlarmState,
eponDeviceDyingGaspAlarmEnabled,
eponDeviceCriticalEventState,
eponDeviceCriticalEventEnabled,
eponDeviceLocalLinkFaultAlarmState,
eponDeviceLocalLinkFaultAlarmEnabled,
eponDeviceTemperatureEventIndicationState,
eponDeviceTemperatureEventIndicationEnabled,
EPON MIB WG Expires October 2004 [Page 60]
Internet-Draft EPON MIBs April 29, 2004
eponDevicePowerVoltageEventIndicationState,
eponDevicePowerVoltageEventIndicationEnabled,
eponDeviceGlobalEventState,
eponDeviceGlobalEventEnabled,
eponDeviceErroredSymbolPeriodEventState,
eponDeviceErroredSymbolPeriodEventEnabled,
eponDeviceErroredFrameEventState,
eponDeviceErroredFrameEventEnabled,
eponDeviceErroredFramePeriodEventState ,
eponDeviceErroredFramePeriodEventEnabled ,
eponDeviceErroredFrameSecondsSummaryEventState ,
eponDeviceErroredFrameSecondsSummaryEventEnabled,
eponDeviceOrganizationSpecificEventState ,
eponDeviceOrganizationSpecificEventEnabled,
eponDeviceEventControl
}
STATUS current
DESCRIPTION
"A collection of objects for EPON device Events"
::= { eponDeviceGroups 4 }
eponDeviceGroupEventLog OBJECT-GROUP
OBJECTS {
eponDeviceEventsLogID,
eponDeviceEventsLogFirstTime,
eponDeviceEventsLogLastTime,
eponDeviceEventsLogCounts,
eponDeviceEventsLogType,
eponDeviceEventsLogEntryStatus
}
STATUS current
DESCRIPTION
"A collection of objects for EPON device Events log"
::= { eponDeviceGroups 5 }
-- Compliance
eponDeviceCompliances OBJECT IDENTIFIER ::= { eponDeviceConformance 2}
eponDeviceCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION "The compliance statement for EPON Devices."
EPON MIB WG Expires October 2004 [Page 61]
Internet-Draft EPON MIBs April 29, 2004
MODULE -- this module
MANDATORY-GROUPS { eponDeviceGroupControl }
GROUP eponDeviceGroupRMadLTable
DESCRIPTION " This group is mandatory for all
EPON devices supporting LLID-MAC address
table."
GROUP eponDeviceGroupStat
DESCRIPTION " This group is mandatory for all
EPON devices supporting interfaces
for Statistics collection."
GROUP eponDeviceGroupEvent
DESCRIPTION " This group is mandatory for all
EPON devices supporting interfaces
for event collection."
GROUP eponDeviceGroupEventLog
DESCRIPTION " This group is mandatory for all
EPON devices supporting interfaces
for event log collection."
::= { eponDeviceCompliances 1}
END
EPON MIB WG Expires October 2004 [Page 62]
Internet-Draft EPON MIBs April 29, 2004
7. Security Considerations
There are number of managed objects defined in this MIB module that
have a MAX-ACCESS clause of read-write. Most objects are writeable
only when the link is Down. Writing to these objects can have the
following potentially disruptive effects on network operation:
Including:
Changing dot3MpcpMode mode
Changing dot3MPCPAdminControl state
Changing eponDeviceObjectReportThreshold
Changing dot3EponMauFecMode mode
Changing eponDeviceObjectReset mode
Changing eponDeviceObjectFecEnabled mode
Changing eponDeviceObjectOamMode mode
Changing eponDeviceObjectDeviceReadyMode
Changing eponDeviceObjectPowerDown
Changing eponDeviceObjectReportThreshold
Changing eponDeviceRMadlLogID
Changing eponDeviceRMadlLLID
Changing eponDeviceRMadlRemoteMacAddress
Changing eponDeviceRMadlType
Changing eponDeviceRMadlAction
Changing eponDeviceRMadlEntryStatus
Changing eponDeviceSampleMinimum
Changing eponDeviceDyingGaspAlarmEnabled
Changing eponDeviceCriticalEventEnabled
Changing eponDeviceLocalLinkFaultAlarmEnabled
Changing eponDeviceTemperatureEventIndicationEnabled
Changing eponDevicePowerVoltageEventIndicationEnabled
Changing eponDeviceGlobalEventEnabled
Changing eponDeviceErroredSymbolPeriodEventEnabled
Changing eponDeviceErroredFrameEventEnabled
Changing eponDeviceErroredFramePeriodEventEnabled
Changing eponDeviceErroredFrameSecondsSummaryEventEnabled
Changing eponDeviceOrganizationSpecificEventEnabled
Changing eponDeviceEventControl
Changing eponDeviceEventsLogID
Changing eponDeviceEventsLogEntryStatus
The user of this MIB module must therefore be aware that support for
SET operations in a non-secure environment without proper protection
can have a negative effect on network operations.
The readable objects in this MIB module (i.e., those with MAX-ACCESS
other than not-accessible) may be considered sensitive in some
environments since, collectively, they provide information about the
performance of network interfaces and can reveal some aspects of
their configuration. In such environments it is important to control
EPON MIB WG Expires October 2004 [Page 63]
Internet-Draft EPON MIBs April 29, 2004
even GET and NOTIFY access to these objects and possibly even to
encrypt their values when sending them over the network via SNMP.
SNMP versions prior to SNMPv3 did not include adequate security. Even
if the network itself is secure (for example by using IPSec), even
then, there is no control as to who on the secure network is allowed
to access and GET/SET (read/change/create/delete) the objects in this
MIB module.
It is RECOMMENDED that implementers consider the security features as
provided by the SNMPv3 framework (see [RFC3410], section 8),
including full support for the SNMPv3 cryptographic mechanisms (for
authentication and privacy).
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module is properly configured to give access to
the objects only to those principals (users) that have legitimate
rights to indeed GET or SET (change/create/delete) them.
8. Intellectual Property
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11. Copies of
claims of rights made available for publication and any assurances of
licenses to be made available, or the result of an attempt made to
obtain a general license or permission for the use of such
proprietary rights by implementers or users of this specification can
be obtained from the IETF Secretariat.
EPON MIB WG Expires October 2004 [Page 64]
Internet-Draft EPON MIBs April 29, 2004
9. Normative References
[802.3] Institute of Electrical and Electronic Engineers, IEEE Std
802.3-2002, "IEEE Standard for Carrier Sense Multiple Access with
Collision Detection (CSMA/CD) Access Method and Physical Layer
Specifications
[802.3ah] Institute of Electrical and Electronic Engineers, IEEE
Draft 802.3ah-2002 Draft 3.3, "IEEE Standard for Carrier Sense
Multiple Access with Collision Detection (CSMA/CD) Access Method and
Physical Layer Specifications - Draft amendment to - Information
technology - Telecommunications and information exchange between
systems - Local and metropolitan area networks - Specific requirements
- Part 3: Carrier sense multiple access with collision detection
(CSMA/CD) access method and physical layer specifications - Media
Access Control Parameters, Physical Layers and Management Parameters
for subscriber access networks
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
McCloghrie, K., Rose, M. and S. Waldbusser, "Structure of Management
Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
McCloghrie, K., Rose, M. and S. Waldbusser, "Textual
Conventions for SMIv2", STD 58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D. and J. Schoenwaelder,
"Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999.
[RFC3636] Flick, J., "Definitions of Managed Objects for IEEE 802.3
Medium Attachment Units (MAUs)", RFC 3636, September 2003.
[RFC2665] Flick, J. and Johnson J. " Definitions of Managed Objects
for the Ethernet-like Interface Types", STD 58, RFC 2580, April 1999.
[draft-ietf-hubmibùefm-mib] Matt Squire "Generic EFM MIB", Internet
draft, draft-ietf-hubmibùefm-mib-00.txt, December 2003
[RFC3591] H-K. Lam, M. Stewart, A. Huynh,
"Definitions of Managed Objects for the Optical Interface Type.",
RFC 3591, September 2003.
[RFC2669] M. St. Johns, Ed.,
"DOCSIS Cable Device MIB Cable Device Management Information
Base for DOCSIS compliant Cable Modems and Cable Modem
Termination Systems.", RFC 2669, August 1999.
[RFC2981] R. Kavasseri,
"Event MIB.", RFC 2981, October 2000.
EPON MIB WG Expires October 2004 [Page 65]
Internet-Draft EPON MIBs April 29, 2004
[RFC1493] E. Decker, P. Langille, A. Rijsinghani, K. McCloghrie,
"Definitions of Managed Objects for Bridges", RFC 1493, July 1993.
[RFC1525]. E. Decker, K. McCloghrie, P. Langille, A. Rijsinghani,
"Definitions of Managed Objects for Source Routing Bridges", RFC 1525,
September 1993.
10. Informative References
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group
MIB", RFC 2863, June 2000.
[RFC2864] McCloghrie, K. and G. Hanson, "The Inverted Stack Table
Extension to the Interfaces Group MIB", RFC 2864, June 2000.
[RFC3410] Case, J., Mundy, R., Partain, D. and B. Stewart,
"Introduction and Applicability Statements for Internet-
Standard Management Framework", RFC 3410, December 2002.
EPON MIB WG Expires October 2004 [Page 66]
Internet-Draft EPON MIBs April 29, 2004
Copyright Notice
Copyright (C) The Internet Society (2003). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published and
distributed, in whole or in part, without restriction of any kind,
provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of developing
Internet standards in which case the procedures for copyrights defined
in the Internet Standards process must be followed, or as required to
translate it into languages other than English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN
WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
AuthorÆs information
Lior Khermosh
Passave Technologies,
Ackerstein Towers, Tower A, 6th floor,
9 Hamenofim St.
Hertzliya Pituach 46725,
ISRAEL
P.O.Box 2089 Hertzliya Pituach 46120 Israel
Tel: +972-9-9717600 Ext: 7181
Fax: +972-9-9540245
Mob: +972-55-224054
lior.khermosh@passave.com
EPON MIB WG Expires October 2004 [Page 67]
| PAFTECH AB 2003-2026 | 2026-04-24 00:01:38 |