One document matched: draft-ietf-hubmib-efm-cu-mib-04.txt
Differences from draft-ietf-hubmib-efm-cu-mib-03.txt
Network Working Group E. Beili
Internet-Draft Actelis Networks
Expires: April 27, 2006 October 24, 2005
Ethernet in the First Mile Copper (EFMCu) Interfaces MIB
draft-ietf-hubmib-efm-cu-mib-04.txt
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on April 27, 2006.
Copyright Notice
Copyright (C) The Internet Society (2005).
Abstract
This document defines a Management Information Base (MIB) module for
use with network management protocols in TCP/IP based internets.
This document proposes an extension to the Ethernet-like Interfaces
MIB and MAU MIB modules with a set of objects for managing an
Ethernet in the First Mile Copper (EFMCu) interfaces 10PASS-TS and
2BASE-TL, defined in IEEE Std 802.3ah-2004.
Beili Expires April 27, 2006 [Page 1]
Internet-Draft EFMCu Interfaces MIB October 2005
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. The Internet-Standard Management Framework . . . . . . . . . . 3
3. Relation to other MIB modules . . . . . . . . . . . . . . . . 4
3.1. Relation to Interfaces Group MIB module . . . . . . . . . 4
3.1.1. Layering Model . . . . . . . . . . . . . . . . . . . . 4
3.1.2. PME Aggregation Function (PAF) . . . . . . . . . . . . 6
3.1.3. Discovery Operation . . . . . . . . . . . . . . . . . 6
3.1.4. EFMCu ports initialization . . . . . . . . . . . . . . 8
3.1.5. Usage of ifTable . . . . . . . . . . . . . . . . . . . 8
3.2. Relation to SHDSL MIB module . . . . . . . . . . . . . . . 9
3.3. Relation to VDSL MIB module . . . . . . . . . . . . . . . 10
3.4. Relation to Ethernet-Like and MAU MIB modules . . . . . . 10
4. MIB Structure . . . . . . . . . . . . . . . . . . . . . . . . 11
4.1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2. PME Profiles . . . . . . . . . . . . . . . . . . . . . . . 11
4.3. Mapping of IEEE 802.3ah Managed Objects . . . . . . . . . 12
5. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . 13
6. Security Considerations . . . . . . . . . . . . . . . . . . . 67
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 69
8. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 69
9. References . . . . . . . . . . . . . . . . . . . . . . . . . . 69
9.1. Normative References . . . . . . . . . . . . . . . . . . . 69
9.2. Informative References . . . . . . . . . . . . . . . . . . 70
Author's Address . . . . . . . . . . . . . . . . . . . . . . . . . 72
Intellectual Property and Copyright Statements . . . . . . . . . . 73
Beili Expires April 27, 2006 [Page 2]
Internet-Draft EFMCu Interfaces MIB October 2005
1. Introduction
New Ethernet-like interfaces have been defined in the Institute of
Electrical and Electronics Engineers (IEEE) Standard 802.3ah-2004
[802.3ah], a.k.a. Ethernet in the First Mile (EFM). In particular
2BASE-TL and 10PASS-TS physical interfaces (PHYs), defined over
voice-grade copper pairs, have been specified for the long and short
reach respectively. These interfaces, collectively called EFMCu, are
based on ITU-T G.SHDSL [G.991.2] and VDSL [G.993.1] specifications
and support variable rates and optional Physical Medium Entity (PME)
aggregation (a.k.a. multi-pair bonding).
2BASE-TL PHY is capable of providing at least 2Mbps over 2700 m long
single copper pair with a mean Bit Error Rate (BER) of 10^-7 (using
5dB target noise margin).
10PASS-TS PHY is capable of providing at least 10Mbps over 750 m long
single copper pair with a mean BER of 10^-7 (using 6dB target noise
margin).
This memo defines a Management Information Base (MIB) module for use
with network management protocols in the Internet community to manage
EFMCu interfaces.
Note that managed objects for Operation, Administration and
Management (OAM) and Ethernet over Passive Optical Networks (EPON)
clauses of IEEE 802.3ah are defined in EFM-COMMON-MIB [I-D.ietf-
hubmib-efm-mib] and EFM-EPON-MIB [I-D.ietf-hubmib-efm-epon-mib]
respectively.
2. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a MIB
module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580].
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
Beili Expires April 27, 2006 [Page 3]
Internet-Draft EFMCu Interfaces MIB October 2005
document are to be interpreted as described in RFC 2119 [RFC2119].
3. Relation to other MIB modules
This section outlines the relationship of this MIB with other MIB
modules described in the relevant RFCs. Specifically, Interfaces
Group MIB (IF-MIB), Ethernet-Like (EtherLike-MIB), MAU (MAU-MIB),
SHDSL (HDSL2-SHDSL-LINE-MIB) and VDSL (VDSL-LINE-EXT-MCM-MIB) are
discussed.
3.1. Relation to Interfaces Group MIB module
2BASE-TL and 10PASS-TS PHY's specified in this MIB module are stacked
Ethernet interfaces and as such are managed using generic interface
management objects defined in the IF-MIB [RFC2863]. The stack
management is done via the ifStackTable, as defined in the IF-MIB
[RFC2863] and ifInvStackTable, as defined in the IF-INVERTED-STACK-
MIB [RFC2864].
3.1.1. Layering Model
An EFMCu interface can aggregate up to 32 Physical Medium Entity
(PME) sub-layer devices (modems), using so called PME Aggregation
Function (PAF).
A generic EFMCu device can have a number of Physical Coding Sublayer
(PCS) ports, connected to a MAC via Medium Independent Interface
(MII) at the upper layer, and cross-connected to a number of
underlying PMEs, with a single PCS per PME relationship, see clause
61.1 of [802.3ah] for more details.
Each PME in the aggregated EFMCu port is represented in the Interface
table (ifTable) as a separate port with ifType of shdsl(169) for
2BASE-TL or vdsl(97) for 10PASS-TS. The ifType values are defined in
[IANAifType-MIB].
ifSpeed for each PME SHALL return the actual data bitrate of the
active PME (e.g. for 2BaseTL PMEs it is a multiple of 64Kbps). Zero
value SHALL be returned when PME is initializing or down.
The ifSpeed of the PCS is the sum of the current operating data rates
of all PMEs in the aggregation group, without the 64/65B
encapsulation overhead and PAF overhead, but acounting for the Inter-
Frame Gaps (IFG).
Beili Expires April 27, 2006 [Page 4]
Internet-Draft EFMCu Interfaces MIB October 2005
When using the stated definition of ifSpeed for the PCS, there would
be no frame loss in the following configuration (the test-sets are
configured to generate 100% of back to back traffic, i.e. minimal
IFG, at 10 or 100Mbps, with min and max frame sizes; the EFM
interfaces are obviously aggregated):
[testset]--10BaseT--[CO]--2BaseTL--[CPE]--10BaseT--[testset]
ifSpeed= 10Mbps 10Mbps 10Mbps
[testset]--100BaseT--[CO]--10PassTS--[CPE]--100BaseT--[testset]
ifSpeed= 100Mbps 100Mbps 100Mbps
Figure 1: Example configuration with no frame loss
The following figure shows the layering diagram and corresponding use
of ifTable and ifMauTable:
_________________________ _
| LLC | |
+-------------------------+ | 1 ifEntry
| MAC | | ifType: ethernetCsmacd(6)
+-------------------------+ > ifMauEntry
| Reconsiliation | | ifMauType: dot3MauType2BaseTL or
+-------------------------+ | dot3MauType10PassTS
| PCS | |
+-------------+---+-------+ +
| TC \ | | | |
+-----\ | | | |
| PMA > PME 1 |...| PME N | > N ifEntry (N=1..32)
+-----/ | | | | ifType: shdsl(169) or vdsl(97)
| PMD/ | | | |
-------------+---+------- -
Figure 2: Use of ifTable and ifMauTable for EFMCu ports
The ifStackTable is indexed by the ifIndex values of the aggregated
EFMCu port (PCS) and the PMEs connected to it. ifStackTable allows a
Network Management application to determine which PMEs are connected
to a particular PCS and change connections (if supported by the
application). The ifInvStackTable, being an inverted version of the
ifStackTable, provides an efficient means for a Network Management
application to read a subset of the ifStackTable and thereby
determine which PCS runs on top of a particular PME.
A new table ifAvailableStackTable defined in this MIB module,
specifies for each PCS a list of PMEs, which can possibly be cross-
connected to that PCS, determined by the cross-connect capability of
the device. This table, modeled after ifStackTable, is read only,
Beili Expires April 27, 2006 [Page 5]
Internet-Draft EFMCu Interfaces MIB October 2005
reflecting current cross-connect capability, which can be dynamic in
some implementations (e.g. if PMEs are located on a pluggable module
and the module is pulled out). Note that PME availability per PCS,
described by ifAvailableStackTable, can be constrained by other
parameters, for example by aggregation capacity of a PCS or by the
PME in question being already connected to another PCS. So, in order
to ensure that a particular PME can be connected to the PCS, all
respective parameters (e.g. ifAvailableStackTable, ifStackTable and
efmCuPAFCapacity) SHALL be inspected.
3.1.2. PME Aggregation Function (PAF)
The PME Aggregation Function (PAF) allows a number of PMEs to be
aggregated onto a PCS port, by fragmenting the Ethernet frames,
transmitting the fragments over multiple PMEs and assembling the
original frames at the remote port. PAF is OPTIONAL, meaning that a
device with a single PME MAY perform fragmentation and re-assembly if
this function is supported by the device. Note however that the
agent is REQUIRED to report on the PAF capability for all EFMCu ports
(2BASE-TL and 10PASS-TS).
This MIB module allows a Network Management application to query PAF
capability and enable/disable it if supported. Note that enabling
PAF effectively turns on fragmentation and re-assembly, even on a
single-PME port.
3.1.3. Discovery Operation
The EFMCu ports may optionally support discovery operation, whereby
PMEs, during initialization, exchange information about their
respective aggregation groups (PCS). This information can then be
used to detect copper missconnections or for an automatic assignment
of the local PMEs into aggregation groups instead of fixed pre-
configuration.
This MIB module allows a Network Management application to control
EFM Discovery mechanism and query its results. Note that the
Discovery mechanism can work only if PAF is supported and enabled.
Two tables are used by Discovery mechanism: ifStackTable and
ifAvailableStackTable defined. The following pseudo-code defines an
example of Discovery and automatic PME assignment for a generic PAF
enabled multi-PCS EFMCu device, located at Central Office (CO), using
objects defined in this MIB module. [Note that automatic PME
assignment is only shown here for the purposes of the example. Fixed
PME pre-assignment, manual assignment or auto-assignment by an
alternative internal algorithm may be chosen by a particular
implementation]:
Beili Expires April 27, 2006 [Page 6]
Internet-Draft EFMCu Interfaces MIB October 2005
FOREACH pcs[i] IN co_device
{ // Discover only on PAF enabled ports with room for more PMEs
IF ( pcs[i].PAFSupported AND pcs[i].NumPMEs < pcs[i].PAFCapacity )
{ dc = pcs[i].DiscoveryCode = MAC[i]; // unique 6 Byte per PCS
// go over all currently disconnected PMEs, which can
// pottentially be connected to PCS[i]
FOREACH pme[j] IN ifAvailableStackTable[pcs[i]] AND
NOT IN ifInvStackTable[pme[j]] // unassigned
{ pme[j].RemoteDiscoveryCode = dc; // Set if Clear
r = pme[j].RemoteDiscoveryCode; // Get
IF ( r == dc AND pcs[i].NumPMEs < pcs[i].PAFCapacity)
{ // Remote CPE connected via PME[j] is/was a peer for
// PCS[i]. Connect this PME to the PCS (there's room)
ADD pme[j] TO ifStackTable[pcs[i]];
pcs[i].NumPMEs = pcs[i].NumPMEs + 1;
// Discover all other currently disconnected PMEs,
// attached to the same CPE and connect them to the PCS
// provided there is enough room for more PMEs.
FOREACH pme[k] IN ifAvailableStackTable[pcs[i]] and
NOT IN ifInvStackTable[pme[k]]
{ r = pme[k].RemoteDiscoveryCode; // Get
IF ( r == dc AND
pcs[i].NumPMEs < pcs[i].PAFCapacity)
{ ADD pme[k] TO ifStackTable[pcs[i]];
pcs[i].NumPMEs = pcs[i].NumPMEs + 1;
}
}
}
// Discovered all PMEs which lead to the same CPE and
// connected them to PCS[i]. Go to the next PCS.
BREAK;
}
}
}
The SNMP Agent builds efmCuStackTable according to the information
contained in the Clause 45 PME_Available_register (see [802.3ah]
61.1.5.3 and 45.2.3.20).
Adding a PME to the ifStackTable row for a specific PCS, involves
actual connection of the PME to the PCS, which can be done by
modifying Clause 45 PME_Aggregate_register (see [802.3ah] 61.1.5.3
and 45.2.3.21).
Note that PCS port does not have to be operationally 'down' for the
connection to succeed. In fact, a dynamic PME addition (and removal)
MAY be implemented whith an available PME being initialized first (by
setting its ifAdminStatus to 'up') and then added to an operationally
Beili Expires April 27, 2006 [Page 7]
Internet-Draft EFMCu Interfaces MIB October 2005
'up' PCS port, by modifying a respective ifStackTable entry.
It is RECOMMENDED that a removal of the last operationally 'up' PME
from an operationally 'up' PCS would be rejected by the
implementation, as this action would completely drop the link.
3.1.4. EFMCu ports initialization
EFMCu ports being built on top of xDSL technology, require a lengthy
initialization or 'training' process, before any data can pass.
During this initialization both ends of a link (peers) work
cooperatively to achieve required data rate on a particular copper
pair. Sometimes, when the copper line is too long or the noise
environment on the line is too high, that 'training' process may fail
to achieve a specific target rate with required characteristics.
The ifAdminStatus object from the IF-MIB, controls the desired state
of a PCS and a PME port. Setting this object to 'up' instructs a
particular PCS or PME to start initialization process, which may take
tens of seconds for EFMCu ports, especially if PAF is involved. The
ifOperStatus object shows the operational state of an interface
(extended by efmCuPmeOperStatus defined in this MIB module for PME
interfaces).
A disconnected PME may be initialized by changing the ifAdminState
from 'down' to 'up'. Changing the ifAdminState to 'up' on the PCS
initializes all PMEs connected to that particular PCS. Note that in
case of PAF some interfaces may fail to initialize while others
succeed. The PCS is considered operationally 'up' if at least one
PME aggregated by its PAF is operationally 'up'. When all PMEs
connected to the PCS are 'down' the PCS SHALL be considered
operationally 'lowerLayerDown'. The PCS SHALL be considered
operationally 'notPresent' if it is not connected to any PME. The
PCS/PME interface SHALL remain operationally 'down' during
initialization.
The efmCuPmeOperStatus defined in this MIB module expands PME's
ifOperStatus value of 'down' to 'downReady', 'downNotReady' and
'init' values, indicating various EFMCu PME specific states.
3.1.5. Usage of ifTable
Both PME and PCS interfaces of the EFMCu PHY are managed using
interface specific management objects defined in this MIB module and
generic interface objects from the ifTable of IF-MIB, with all
management table entries referenced by the interface index ifIndex.
The following table summarizes EFMCu specific interpretations for
Beili Expires April 27, 2006 [Page 8]
Internet-Draft EFMCu Interfaces MIB October 2005
some of the ifTable objects specified by the mandatory
ifGeneralInformationGroup:
+---------------+---------------------------------------------------+
| IF-MIB object | EFMCu interpretation |
+---------------+---------------------------------------------------+
| ifIndex | Interface index. Note that each PME and each PCS |
| | in the EFMCu PHY MUST have a unique index, as |
| | there some PCS and PME specific attributes |
| | accessible only on the PCS or PME level. |
| ifType | ethernetCsmacd(6) for PCS, shdsl(169) for |
| | 2BASE-TL PME, vdsl(97) for 10PASS-TS PME |
| ifSpeed | Operating data rate for the PME. For the PCS it |
| | is the sum of the current operating data rates of |
| | all PMEs in the aggregation group, without the |
| | 64/65B encapsulation overhead and PAF overhead, |
| | but acounting for the Inter-Frame Gaps (IFG) |
| ifAdminStatus | Setting this object to 'up' instructs a |
| | particular PCS (with all PMEs connected to it) or |
| | PME to start initialization process |
| ifOperStatus | efmCuPmeOperStatus supplements the 'down' value |
| | of ifOperStatus for PMEs. |
+---------------+---------------------------------------------------+
Table 1
3.2. Relation to SHDSL MIB module
G.SHDSL.bis modems, similar to PME(s) comprising a 2BASE-TL port, are
described in HDSL2-SHDSL-LINE-MIB [I-D.ietf-adslmib-gshdslbis]. Note
that not all attributes of G.SHDSL modems reflected in HDSL2-SHDSL-
LINE-MIB have adequate management objects (Clause 30 attributes and
Clause 45 registers) in the EFM standard.
Because of these differences and for the purposes of simplicity,
unification of attributes common to both 2BASE-TL and 10PASS-TS PMEs
and name consistency (e.g. prefixing the 2BASE-TL PME related objects
with 'efmCuPme2B' instead of 'hdsl2shdsl'), it was decided not to
reference HDSL2-SHDSL-LINE-MIB objects, but define all the relevant
objects in this MIB module.
However, if some functionality, not available in this MIB module, is
required and supported by the PME, e.g. performance monitoring,
relevant HDSL2-SHDSL-LINE-MIB groups MAY be included and aplied for
PMEs of 2BASE-TL subtype.
Beili Expires April 27, 2006 [Page 9]
Internet-Draft EFMCu Interfaces MIB October 2005
3.3. Relation to VDSL MIB module
VDSL (DMT) modems, similar to the PME(s) comprising a 10PASS-TS port,
are described in VDSL-LINE-EXT-MCM-MIB [RFC4070]. Note that not all
attributes of VDSL modems reflected in VDSL-LINE-EXT-MCM-MIB have
adequate management objects (Clause 30 attributes and Clause 45
registers) in the EFM standard.
Because of these differences and for the purposes of simplicity,
unification of attributes common to both 2BASE-TL and 10PASS-TS PMEs
and name consistency, it was decided not to reference VDSL-LINE-EXT-
MCM-MIB objects, but define all the relevant objects in this MIB
module.
However, if some functionality, not available in this MIB module, is
required and supported by the PME, relevant VDSL-LINE-EXT-MCM-MIB
groups MAY be included and applied for PMEs of 10PASS-TS subtype.
3.4. Relation to Ethernet-Like and MAU MIB modules
The implementation of EtherLike-MIB [RFC3635] and MAU-MIB [I-D.ietf-
hubmib-rfc3636bis] is REQUIRED for the EFMCu interfaces.
Two new values of ifMauType (OBJECT-IDENTITIES of dot3MauType) and
corresponding bit definitions of ifMauTypeListBits
(IANAifMauTypeListBits) have been defined in the IANA-MAU-TC-MIB
[I-D.ietf-hubmib-rfc3636bis] for the EFMCu MAUs:
o dot3MauType2BaseTL and b2BaseTL - for 2BASE-TL MAU
o dot3MauType10PassTS and b10PassTS - for 10PASS-TS MAU
As an EtherLike interface every EFMCu port (an ifEntry representing a
consolidation of LLC, MAC and PCS (sub)layers) SHALL return an ifType
of ethernetCsmacd(6). While most of the MAU characteristics are not
applicable to the EFMCu ports (no auto-negotiation, media available,
false carriers or jabber), they SHALL return an appropriate ifMauType
(dot3MauType2BaseTL or dot3mauType10PassTS) in order to direct the
management software to look in the EFM-CU-MIB for the desired
information. For example the information on the particular EFMCu
flavor that an EFMCu port is running is available from
efmCuOperSubType, defined in this MIB module.
Since EFMCu PMEs are not EtherLike interfaces, they cannot be
instantiated as MAU interface objects.
Beili Expires April 27, 2006 [Page 10]
Internet-Draft EFMCu Interfaces MIB October 2005
4. MIB Structure
4.1. Overview
The main management objects defined in this MIB module are split into
2 groups:
o efmCuPort - containing objects for configuration, capabilities,
status and notifications, common to all EFMCu PHYs.
o efmCuPme - containing objects for configuration, capabilities,
status and notifications of EFMCu PMEs.
In addition the ifAvailableStackTable is defined at the same level.
The efmCuPme group in turn contains efmCuPme2B and efmCuPme10P
groups, which define PME Profiles specific to 2BASE-TL and 10PASS-TS
PMEs respectively, as well as PME specific status information.
4.2. PME Profiles
Since a managed node can have a large number of EFMCu PHYs,
provisioning every parameter on every EFMCu PHY may become
burdensome. Moreover, most PMEs are provisioned identically with the
same set of parameters. To simplify the provisioning process, this
MIB module makes use of configuration profiles, similar to HDSL2-
SHDSL-LINE-MIB and VDSL-LINE-EXT-MCM-MIB. A profile is a set of
parameters, used either for configuration or representation of a PME.
The same profile can be shared by multiple PME ports, using the same
configuration.
The PME profiles are defined in efmCuPme2BProfileTable and
efmCu10PProfileTable for 2BASE-TL and 10PASS-TS PMEs respectively.
There are 12 predefined standard profiles for 2BASE-TL and 22
standard profiles for 10PASS-TS, defined in 802.3ah and dedicated for
rapid provisioning of EFMCu PHYs in most scenarios. In addition this
MIB defines two additional predefined profiles for "best-effort"
provisioning of 2BASE-TL PMEs. An ability to define new
configuration profiles is also provided to allow for EFMCu deployment
tailored to specific copper environment and spectral regulations.
A specific configuration or administrative profile is assigned to a
specific PME via efmCuPmeAdminProfile object. If
efmCuPmeAdminProfile is zero, then efmCuAdminProfile object of the
PCS port, connected to the PME, determines the configuration profile
(or a list of possible profiles) for that PME. This mechanism allows
to specify a common profile(s) for all PMEs connected to the PCS
port, with an ability to change individual PME profiles by setting
Beili Expires April 27, 2006 [Page 11]
Internet-Draft EFMCu Interfaces MIB October 2005
efmCuPmeAdminProfile object, which overwrites profile set by
efmCuAdminProfile.
A current operating PME profile is pointed to by efmCuPmeOperProfile
object. Note that this profile entry, can be created automatically,
to reflect achieved parameters in adaptive (not fixed)
initialization.
4.3. Mapping of IEEE 802.3ah Managed Objects
This section contains the mapping between managed objects
(attributes) defined in [802.3ah] Clause 30, and managed objects
defined in this document and in associated MIB modules, i.e., the IF-
MIB [RFC2863].
Note that majority of the objects defined in this MIB module do not
have direct counterparts in Clause 30 and instead refer to Clause 45
registers.
+---------------------------------+---------------------------------+
| IEEE 802.3 Managed Object | Corresponding SNMP Object |
+---------------------------------+---------------------------------+
| oPAF - Basic Package | |
| (Mandatory) | |
| aPAFID | ifIndex (IF-MIB) |
| aPhyEnd | efmCuPhySide |
| aPHYCurrentStatus | efmCuStatus |
| aPAFSupported | efmCuPAFSupported |
| oPAF - PME Aggregation Package | |
| (Optional) | |
| aPAFAdminState | efmCuPAFAdminState |
| aLocalPAFCapacity | efmCuPAFCapacity |
| aLocalPMEAvailable | ifAvailableStackTable |
| aLocalPMEAggregate | ifStackTable (IF-MIB) |
| aRemotePAFSupported | efmCuRemotePAFSupported |
| aRemotePAFCapacity | efmCuRemotePAFCapacity |
| aRemotePMEAggregate | |
| oPME - 10P/2B Package | |
| (Mandatory) | |
| aPMEID | ifIndex (IF-MIB) |
| aPMEAdminState | ifAdminState (IF-MIB) |
| aPMEStatus | efmCuPmeStatus |
| aPMESNRMgn | efmCuPmeSnrMgn |
| aTCCodingViolations | efmCuPmeTCCodingErrors |
| aTCCRCErrors | efmCuPmeTCCrcErrors |
| aProfileSelect | efmCuAdminProfile, |
| | efmCuPmeAdminProfile |
| aOperatingProfile | efmCuPmeOperProfile |
Beili Expires April 27, 2006 [Page 12]
Internet-Draft EFMCu Interfaces MIB October 2005
| aPMEFECCorrectedBlocks | efmCuPme10PFECCorrectedBlocks |
| aPMEFECUncorrectableBlocks | efmCuPme10PFECUncorrectedBlocks |
+---------------------------------+---------------------------------+
Table 2
5. Definitions
EFM-CU-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Integer32,
Unsigned32, Counter32, mib-2
FROM SNMPv2-SMI -- RFC 2578
TEXTUAL-CONVENTION, TruthValue, RowStatus, PhysAddress
FROM SNMPv2-TC -- RFC 2579
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF -- RFC 2580]
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB -- RFC 3411
ifIndex, ifSpeed, InterfaceIndex
FROM IF-MIB -- RFC 2863
;
efmCuMIB MODULE-IDENTITY
LAST-UPDATED "200510240000Z" -- October 24, 2005
ORGANIZATION "IETF Ethernet Interfaces and Hub MIB Working Group"
CONTACT-INFO
"WG charter:
http://www.ietf.org/html.charters/hubmib-charter.html
Mailing Lists:
General Discussion: hubmib@ietf.org
To Subscribe: hubmib-request@ietf.org
In Body: subscribe your_email_address
Chair: Dan Romascanu
Postal: Avaya
Atidim Technology Park, Bldg. 3
Tel Aviv 61131
Israel
Tel: +972 3 645 8414
E-mail: dromasca@avaya.com
Editor: Edward Beili
Postal: Actelis Networks Inc.
Beili Expires April 27, 2006 [Page 13]
Internet-Draft EFMCu Interfaces MIB October 2005
25 Bazel St., P.O.B. 10173
Petach-Tikva 10173
Israel
Tel: +972-3-924-3491
E-mail: edward.beili@actelis.com"
DESCRIPTION
"The objects in this MIB module are used to manage
the Ethernet in the First Mile (EFM) Copper (EFMCu) Interfaces
2BASE-TL and 10PASS-TS, defined in IEEE Std. 802.3ah-2004.
The following reference is used throughout this MIB module:
[802.3ah] refers to:
IEEE Std 802.3ah-2004: 'IEEE Standard for Information
technology - Telecommunications and information exchange
between systems - Local and metropolitan area networks -
Specific requirements -
Part 3: Carrier Sense Multiple Access with Collision
Detection (CSMA/CD) Access Method and Physical Layer
Specifications -
Amendment: Media Access Control Parameters, Physical
Layers and Management Parameters for Subscriber Access
Networks', 07 September 2004.
Of particular interest are Clause 61, 'Physical Coding
Sublayer (PCS) and common specifications, type 10PASS-TS and
type 2BASE-TL', Clause 30, 'Management', Clause 45,
'Management Data Input/Output (MDIO) Interface', Annex 62A,
'PMD profiles for 10PASS-TS' and Annex 63A, 'PMD profiles for
2BASE-TL'.
Naming Conventions:
Atn - Attenuation
CO - Central Office
CPE - Customer Premises Equipment
EFM - Ethernet in the First Mile
EFMCu - EFM Copper
MDIO - Management Data Input/Output
Mgn - Margin
PAF - PME Aggregation Function
PCS - Physical Coding Sublayer
PMD - Physical Medium Dependent
PME - Physical Medium Entity
PSD - Power Spectral Density
SNR - Signal to Noise Ratio
TCPAM - Trellis Coded Pulse Amplitude Modulation
Beili Expires April 27, 2006 [Page 14]
Internet-Draft EFMCu Interfaces MIB October 2005
Copyright (C) The Internet Society (2004). This version
of this MIB module is part of RFC XXXX; see the RFC
itself for full legal notices."
REVISION "200510240000Z" -- October 24, 2005
DESCRIPTION "Initial version, published as RFC XXXX."
-- EdNote: Replace XXXX with the actual RFC number &
-- remove this note
::= { mib-2 YYY }
-- EdNote: Replace YYY with a real OID once it is
-- allocated & remove this note.
-- Sections of the module
efmCuObjects OBJECT IDENTIFIER ::= { efmCuMIB 1 }
efmCuConformance OBJECT IDENTIFIER ::= { efmCuMIB 2 }
-- Groups in the module
efmCuPort OBJECT IDENTIFIER ::= { efmCuObjects 1 }
efmCuPme OBJECT IDENTIFIER ::= { efmCuObjects 2 }
-- Textual Conventions
ProfileIndex ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"A unique value, greater than zero, for each PME configuration
profile in the managed EFMCu port. It is recommended that
values are assigned contiguously starting from 1. The value
for each profile must remain constant at least from one
re-initialization of the entity's network management system
to the next re-initialization."
SYNTAX Unsigned32 (1..255)
ProfileIndexOrZero ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"This textual convention is an extension of the ProfileIndex
convention. The latter defines a greater than zero value used
to identify a PME profile in the managed EFMCu port. This
Beili Expires April 27, 2006 [Page 15]
Internet-Draft EFMCu Interfaces MIB October 2005
extension permits the additional value of zero. The value of
zero is object-specific and must therefore be defined as part
of the description of any object which uses this syntax.
Examples of the usage of zero value migh include situations
where current operational profile is unknown."
SYNTAX Unsigned32 (0..255)
ProfileIndexList ::= TEXTUAL-CONVENTION
DISPLAY-HINT "1d:"
STATUS current
DESCRIPTION
"Represents a list of up to 6 ProfileIndex's.
The ProfileIndex textual convention defines a greater than
zero value used to identify a PME profile in the managed EFMCu
port. The value of this object is a concatenation of one or
more (up to 6) octets, where each octet contains an 8-bit
ProfileIndex value.
The ProfileIndexList specifies a list of alternative
profiles, any of which can be chosen for configuration of an
PME."
SYNTAX OCTET STRING (SIZE(1..6))
TruthValueOrUnknown ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This textual convention is an extension of the TruthValue
convention. The latter defines a boolean value with
possible values of true(1) and false(2). This
extension permits the additional value of unknown(0), which
can be returned as a result of GET operation, when an exact
true or false value of the object cannot be determined."
SYNTAX INTEGER { unknown(0), true(1), false(2) }
-- Port Notifications Group
efmCuPortNotifications OBJECT IDENTIFIER ::= { efmCuPort 0 }
efmCuLowBandwidth NOTIFICATION-TYPE
OBJECTS {
-- ifIndex is not needed here since we are under specific PCS
ifSpeed,
efmCuThreshLowBandwidth
}
STATUS current
DESCRIPTION
"This notification indicates that EFMCu port's data rate
reached or dropped below a Low Bandwidth Threshold
(i.e. bandwidth degradation happening in case of PAF when one
Beili Expires April 27, 2006 [Page 16]
Internet-Draft EFMCu Interfaces MIB October 2005
or more PMEs drop)."
-- EdNote: add throttling limitations here
::= { efmCuPortNotifications 1 }
-- PCS Port group
efmCuPortConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF EfmCuPortConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table for Configuration of EFMCu 2BASE-TL/10PASS-TS (PCS)
Ports. Entries in this table MUST be maintained in a
persistent manner"
::= { efmCuPort 1 }
efmCuPortConfEntry OBJECT-TYPE
SYNTAX EfmCuPortConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the EFMCu Port Configuration table.
Each entry represents an EFMCu port indexed by the ifIndex.
Note that an EFMCu PCS port runs on top of a single
or multiple PME port(s), which are also indexed by ifIndex."
INDEX { ifIndex }
::= { efmCuPortConfTable 1 }
EfmCuPortConfEntry ::=
SEQUENCE {
efmCuPAFAdminState INTEGER,
efmCuPAFDiscoveryCode PhysAddress,
efmCuAdminProfile ProfileIndexList,
efmCuTargetDataRate Unsigned32,
efmCuTargetSnrMgn Unsigned32,
efmCuThreshLowBandwidth Unsigned32,
efmCuLowBandwidthEnable TruthValue
}
efmCuPAFAdminState OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administrative (desired) state of the PAF of the EFMCu port
Beili Expires April 27, 2006 [Page 17]
Internet-Draft EFMCu Interfaces MIB October 2005
(PCS).
When 'disabled', PME Aggregation will not be performed by the
PCS. No more than a single PME can be assigned to this PCS in
this case.
When 'enabled', PAF will be performed by the PCS when the link
is Up, even on a single attached PME, if PAF is supported.
PCS ports incapable of supporting PAF SHALL return a value of
'disabled'. Attempts to 'enable' such ports SHALL be ignored.
PAF 'enabled' port with multiple PMEs assigned cannot be
'disabled'. Attempts to 'disable' such port SHALL be rejected,
until at most one PME is left assigned.
Changing PAFAdminState is a traffic disruptive operation and
as such SHALL be done when the link is Down. Attempts to
change this object SHALL be ignored if the link is Up or
Initializing.
This object maps to the Clause 30 attribute aPAFAdminState.
If a Clause 45 MDIO Interface to the PCS is present, then this
object maps to the PAF enable bit in the 10P/2B PCS control
register.
This object MUST be maintained in a persistent manner."
REFERENCE
"[802.3ah] 61.2.2, 45.2.3.18.3"
::= { efmCuPortConfEntry 1 }
efmCuPAFDiscoveryCode OBJECT-TYPE
SYNTAX PhysAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"PAF Discovery Code of the EFMCu port (PCS).
A unique 6 Byte long code used by the Discovery function, when
PAF is supported.
PCS ports incapable of supporting PAF SHALL return a value of
all zeroes. Attempts to change this object SHALL be ignored in
this case.
This object MUST be instantiated for the -O subtype PCS before
writing operations on the efmCuPAFRemoteDiscoveryCode
(Set_if_Clear and Clear_if_Same) are performed by PMEs
associated with the PCS.
The value of this object is read-only for -R port subtypes.
The initial value of this object for -R ports after reset
is 0. This value may be changed as a result of writing
Beili Expires April 27, 2006 [Page 18]
Internet-Draft EFMCu Interfaces MIB October 2005
operation on efmCuPAFRemoteDiscoveryCode variable of remote
PME of -O subtype, connected to one of the local PMEs
associated with the PCS.
Discovery MUST be performed when the link is Down.
Attempts to change this object MUST be rejected with the error
inconsistentValue if the link is Up or Initializing.
The PAF Discovery code maps to the local Discovery code
variable in PAF (note that it does not have a corresponding
Clause 45 register)"
REFERENCE
"[802.3ah] 61.2.2.8.3, 61.2.2.8.4, 45.2.6.6.1"
::= { efmCuPortConfEntry 2 }
efmCuAdminProfile OBJECT-TYPE
SYNTAX ProfileIndexList
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Desired configuration Profile(s), common for all PMEs in the
EFMCu port. This object is a list of pointers to entries in
either efmCuPme2BProfileTable or
efmCuPme10PProfileTable, depending on the current
operating SubType of the EFMCu port as indicated by
efmCuPortSide.
The value of this object is a list of up to 6 indices of
Profiles. If this list consists of a single Profile index,
then all PMEs assigned to this EFMCu port SHALL be configured
according to the Profile referenced by that index, unless it
is overwritten by corresponding non-zero efmCuPmeAdminProfile,
which takes precedence over efmCuAdminProfile.
The list, consisting of more than one index, allows each PME
in the port to be configured according to any Profile
specified in the list.
By default this object has a value of 0x01, referencing 1st
entry in efmCuPme2BProfileTable or efmCuPme10PProfileTable.
This object is writable and readable for the -O subtype
(2BaseTL-O or 10PassTS-O) EFMCu ports. It is unavailable for
the -R subtype (2BaseTL-R or 10PassTS-R) ports.
Note that current operational Profile value is available via
efmCuPmeOperProfile object.
Modification of this object must be performed when the link is
Down. Attempts to change this object MUST be rejected, if the
link is Up or Initializing.
Beili Expires April 27, 2006 [Page 19]
Internet-Draft EFMCu Interfaces MIB October 2005
Attempts to set this object to a list with a member
value, that is not the value of the index for an active entry
in the corresponding profile table, MUST be rejected.
This object MUST be maintained in a persistent manner."
REFERENCE
"[802.3ah] 30.11.2.1.6"
DEFVAL { '01'H }
::= { efmCuPortConfEntry 3 }
efmCuTargetDataRate OBJECT-TYPE
SYNTAX Unsigned32(1..100000|999999)
UNITS "Kbps"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Desired EFMCu port 'net' (as seen across MII) Data Rate in
Kbps, to be achieved during initialization, under spectral
restrictions placed on each PME via efmCuAdminProfile or
efmCuPmeAdminProfile, with the desired SNR Margin specified by
efmCuTargetSnrMgn.
In case of PAF, this object represents a sum of individual PME
data rates, modified to compensate for fragmentation and
64/65B framing overhead (e.g. target data rate of 10Mbps
shall allow lossless transmission of full-duplex 10Mbps
Ethernet frame stream with minimal inter-frame gap).
The value is limited above by 100Mbps as this is the max
burst rate across MII for EFMCu ports.
The value between 1 and 100000 indicates that the total data
rate (ifSpeed) of the EFMCu port after initialization should
be equal to the target data rate or less, if the target data
rate cannot be achieved under spectral restrictions specified
by efmCuAdminProfile/efmCuPmeAdminProfile and with desired SNR
margin. In case the copper environment allows to achieve
higher total data rate than specified by the target, the
excess capability SHALL be converted to additional SNR margin
and spread evenly across all active PMEs assigned to the (PCS)
port.
The value of 999999 means that the target data rate is not
fixed and should be set to the maximum attainable rate during
initialization (Best Effort), under specified spectral
restrictions and with desired SNR Margin.
This object is read-write for the -O subtype EFMCu ports
(2BaseTL-O/10PassTS-O) and not available for the -R subtypes.
Beili Expires April 27, 2006 [Page 20]
Internet-Draft EFMCu Interfaces MIB October 2005
Changing of the Target Data Rate MUST be performed when the
link is Down. Attempts to change this object MUST be rejected
with the error inconsistentValue, if the link is Up or
Initializing.
Note that current Data Rate of the EFMCu port is represented
by ifSpeed object of IF-MIB.
This object MUST be maintained in a persistent manner."
::= { efmCuPortConfEntry 4 }
efmCuTargetSnrMgn OBJECT-TYPE
SYNTAX Unsigned32(0..21)
UNITS "dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Desired EFMCu port SNR Margin to be achieved on all PMEs
assigned to the port, during initializiation. (The SNR margin
is the difference between the desired SNR and the actual SNR).
Note that 802.3ah recommends using default Target SNR Margin
of 5dB for 2BASE-TL ports and 6dB for 10PASS-TS ports in order
to achieve mean Bit Error Rate (BER) of 10^-7 at the PMA
service interface.
This object is read-write for the -O subtype EFMCu ports
(2BaseTL-O/10PassTS-O) and not available for the -R subtypes.
Changing of the Target SNR Margin MUST be performed when the
link is Down. Attempts to change this object MUST be rejected
with the error inconsistentValue, if the link is Up or
Initializing.
Note that current SNR Margin of the PMEs comprising the EFMCu
port is represented by efmCuPmeSnrMgn.
This object MUST be maintained in a persistent manner."
REFERENCE
"[802.3ah] 61.1.2"
::= { efmCuPortConfEntry 5 }
efmCuThreshLowBandwidth OBJECT-TYPE
SYNTAX Unsigned32(400..100000)
UNITS "Kbps"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
Beili Expires April 27, 2006 [Page 21]
Internet-Draft EFMCu Interfaces MIB October 2005
"This object configures the EFMCu port Low Bandwidth alarm
threshold. When the current value of ifSpeed for this port
reaches or drops below this threshold, an
efmCuLowBandwidth notification MAY be generated if enabled by
efmCuLowBandwidthEnable.
This object is read-write for the -O subtype EFMCu ports
(2BaseTL-O/10PassTS-O) and not available for the -R subtypes.
This object MUST be maintained in a persistent manner."
::= { efmCuPortConfEntry 6 }
efmCuLowBandwidthEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether efmCuLowBandwidth notifications should be
generated for this interface.
Value of true(1) indicates that efmCuLowBandwidth
notification is enabled. Value of false(2) indicates that
the notification is disabled.
This object MUST be maintained in a persistent manner."
::= { efmCuPortConfEntry 7 }
efmCuPortCapabilityTable OBJECT-TYPE
SYNTAX SEQUENCE OF EfmCuPortCapabilityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table for Capabilities of EFMCu 2BASE-TL/10PASS-TS (PCS)
Ports. Entries in this table MUST be maintained in a
persistent manner"
::= { efmCuPort 2 }
efmCuPortCapabilityEntry OBJECT-TYPE
SYNTAX EfmCuPortCapabilityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the EFMCu Port Capability table.
Each entry represents an EFMCu port indexed by the ifIndex.
Note that an EFMCu PCS port runs on top of a single
or multiple PME port(s), which are also indexed by ifIndex."
INDEX { ifIndex }
Beili Expires April 27, 2006 [Page 22]
Internet-Draft EFMCu Interfaces MIB October 2005
::= { efmCuPortCapabilityTable 1 }
EfmCuPortCapabilityEntry ::=
SEQUENCE {
efmCuPAFSupported TruthValue,
efmCuPeerPAFSupported TruthValueOrUnknown,
efmCuPAFCapacity Unsigned32,
efmCuPeerPAFCapacity Unsigned32
}
efmCuPAFSupported OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"PME Aggregation Function (PAF) Capability of the EFMCu port
(PCS).
This object has a value of true(1) when the PCS can perform
PME aggregation on the available PMEs.
Ports incapable of PAF SHALL return a value of false(2).
This object maps to the Clause 30 attribute aPAFSupported.
If a Clause 45 MDIO Interface to the PCS is present,
then this object maps to the PAF available bit in the
10P/2B capability register."
REFERENCE
"[802.3ah] 61.2.2, 30.11.1.1.4, 45.2.3.17.1"
::= { efmCuPortCapabilityEntry 1 }
efmCuPeerPAFSupported OBJECT-TYPE
SYNTAX TruthValueOrUnknown
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"PME Aggregation Function (PAF) Capability of the EFMCu port
(PCS) link partner.
This object has a value of true(1) when the remote PCS can
perform PME aggregation on its available PMEs.
Ports whose peers are incapable of PAF, SHALL return a value
of false(2).
Ports whose peers cannot be reached because of the link
state, SHALL return a value if unknown(0).
This object maps to the Clause 30 attribute
aRemotePAFSupported.
If a Clause 45 MDIO Interface to the PCS is present, then
Beili Expires April 27, 2006 [Page 23]
Internet-Draft EFMCu Interfaces MIB October 2005
this object maps to the Remote PAF supported bit in the
10P/2B capability register."
REFERENCE
"[802.3ah] 61.2.2, 30.11.1.1.9, 45.2.3.17.2"
::= { efmCuPortCapabilityEntry 2 }
efmCuPAFCapacity OBJECT-TYPE
SYNTAX Unsigned32 (1..32)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of PMEs that can be aggregated by the local PAF.
The number of PMEs currently assigned to a particular
EFMCu port (efmCuNumPMEs) is never greater than
efmCuPAFCapacity.
This object maps to the Clause 30 attribute
aLocalPAFCapacity."
REFERENCE
"[802.3ah] 61.2.2, 30.11.1.1.6"
::= { efmCuPortCapabilityEntry 3 }
efmCuPeerPAFCapacity OBJECT-TYPE
SYNTAX Unsigned32 (0|1..32)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of PMEs that can be aggregated by the PAF of the peer
Phy (PCS port).
Value of 0 is returned when peer PAF Capacity is unknown
(peer cannot be reached).
This object maps to the Clause 30 attribute
aRemotePAFCapacity."
REFERENCE
"[802.3ah] 61.2.2, 30.11.1.1.10"
::= { efmCuPortCapabilityEntry 4 }
efmCuPortStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF EfmCuPortStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides overall status information of EFMCu
2BASE-TL/10PASS-TS ports. This table contains live data from
the equipment. As such, it is NOT persistent."
::= { efmCuPort 3 }
Beili Expires April 27, 2006 [Page 24]
Internet-Draft EFMCu Interfaces MIB October 2005
efmCuPortStatusEntry OBJECT-TYPE
SYNTAX EfmCuPortStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the EFMCu Port Status table.
Each entry represents an EFMCu port indexed by the ifIndex.
Note that an EFMCu PCS port runs on top of a single
or multiple PME port(s), which are also indexed by ifIndex."
INDEX { ifIndex }
::= { efmCuPortStatusTable 1 }
EfmCuPortStatusEntry ::=
SEQUENCE {
efmCuFltStatus BITS,
efmCuPortSide INTEGER,
efmCuNumPMEs Unsigned32,
efmCuPAFInErrors Counter32,
efmCuPAFInSmallFragments Counter32,
efmCuPAFInLargeFragments Counter32,
efmCuPAFInBadFragments Counter32,
efmCuPAFInLostFragments Counter32,
efmCuPAFInLostStarts Counter32,
efmCuPAFInLostEnds Counter32,
efmCuPAFInOverflows Counter32
}
efmCuFltStatus OBJECT-TYPE
SYNTAX BITS {
noPeer(0),
pmeSubTypeMismatch(1),
lowBandwidth(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"EFMCu (PCS) port Fault Status. This is a bitmap of possible
conditions. The various bit positions are:
noPeer - peer PHY cannot be reached (e.g.
no PMEs attached, all PMEs are Down
etc.) More info is available in
efmCuPmeFltStatus.
pmeSubTypeMismatch - local PMEs in the aggregation group
are not of the same sub-type, e.g.
some PMEs in the local device are -O
while others are -R subtype.
lowBandwidth - ifSpeed of the port reached or droped
below efmCuThreshLowBandwidth
Beili Expires April 27, 2006 [Page 25]
Internet-Draft EFMCu Interfaces MIB October 2005
This object is intended to supplement ifOperStatus object
in IF-MIB.
Additional information is available via efmCuPmeFltStatus
object for each PME in the aggregation group (single PME if
PAF is disabled)."
REFERENCE
"ifOperStatus in IF-MIB; efmCuPmeFltStatus"
::= { efmCuPortStatusEntry 1 }
efmCuPortSide OBJECT-TYPE
SYNTAX INTEGER {
subscriber(1),
office(2),
unknown(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"EFM port mode of operation (subtype).
The value of 'subscriber' indicates the port is designated as
'-R' subtype (all PMEs assigned to this port are of subtype
'-R').
The value of the 'office' indicates that the port is
designated as '-O' subtype (all PMEs assigned to this port are
of subtype '-O').
The value of 'unknown' indicates that the port has no assigned
PMEs yet or that the assigned PMEs are not of the same side
(subTypePMEMismatch).
This object partially maps to the Clause 30 attribute
aPhyEnd"
REFERENCE
"[802.3ah] 61.1, 30.11.1.1.2"
::= { efmCuPortStatusEntry 2 }
efmCuNumPMEs OBJECT-TYPE
SYNTAX Unsigned32 (0..32)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of PMEs that is currently aggregated by the local PAF
(assigned to the EFMCu port using ifStackTable).
This number is never greater than efmCuPAFCapacity.
This object SHALL be automatically incremented or decremented
when a PME is added or deleted to/from the EFMCu port using
ifStackTable."
REFERENCE
Beili Expires April 27, 2006 [Page 26]
Internet-Draft EFMCu Interfaces MIB October 2005
"[802.3ah] 61.2.2, 30.11.1.1.6"
::= { efmCuPortStatusEntry 3 }
efmCuPAFInErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A number of fragments that have been received across the
gamma interface with RxErr asserted and discarded.
This read-only counter is inactive (not incremented) when the
PAF is unsupported or disabled. Upon disabling the PAF, the
counter retains its previous value.
If a Clause 45 MDIO Interface to the PCS is present, then
this object maps to the 10P/2B PAF RX error register."
REFERENCE
"[802.3ah] 45.2.3.21"
::= { efmCuPortStatusEntry 4 }
efmCuPAFInSmallFragments OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A number of fragments smaller than minFragmentSize
(64 Bytes), that have been received across the gamma interface
and discarded.
This read-only counter is inactive when the PAF is
unsupported or disabled. Upon disabling the PAF, the counter
retains its previous value.
If a Clause 45 MDIO Interface to the PCS is present, then
this object maps to the 10P/2B PAF small fragments
register."
REFERENCE
"[802.3ah] 45.2.3.22"
::= { efmCuPortStatusEntry 5 }
efmCuPAFInLargeFragments OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A number of fragments larger than maxFragmentSize
(512 Bytes), that have been received across the gamma
interface and discarded.
This read-only counter is inactive when the PAF is
Beili Expires April 27, 2006 [Page 27]
Internet-Draft EFMCu Interfaces MIB October 2005
unsupported or disabled. Upon disabling the PAF, the counter
retains its previous value.
If a Clause 45 MDIO Interface to the PCS is present, then
this object maps to the 10P/2B PAF large fragments
register."
REFERENCE
"[802.3ah] 45.2.3.23"
::= { efmCuPortStatusEntry 6 }
efmCuPAFInBadFragments OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A number of fragments which do not fit into the sequence
expected by the frame assembly function, that have been
received across the gamma interface and discarded (the
frame buffer is flushed to the next valid frame start).
This read-only counter is inactive when the PAF is
unsupported or disabled. Upon disabling the PAF, the counter
retains its previous value.
If a Clause 45 MDIO Interface to the PCS is present, then
this object maps to the 10P/2B PAF bad fragments
register."
REFERENCE
"[802.3ah] 45.2.3.25"
::= { efmCuPortStatusEntry 7 }
efmCuPAFInLostFragments OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A number of gaps in the sequence of fragments, that have been
received across the gamma interface (the frame buffer is
flushed to the next valid frame start, when fragment/fragments
expected by the frame assembly function is/are not received).
This read-only counter is inactive when the PAF is
unsupported or disabled. Upon disabling the PAF, the counter
retains its previous value.
If a Clause 45 MDIO Interface to the PCS is present, then
this object maps to the 10P/2B PAF lost fragment
register."
REFERENCE
"[802.3ah] 45.2.3.26"
Beili Expires April 27, 2006 [Page 28]
Internet-Draft EFMCu Interfaces MIB October 2005
::= { efmCuPortStatusEntry 8 }
efmCuPAFInLostStarts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A number of missing StartOfPacket indicators expected by the
frame assembly function.
This read-only counter is inactive when the PAF is
unsupported or disabled. Upon disabling the PAF, the counter
retains its previous value.
If a Clause 45 MDIO Interface to the PCS is present, then
this object maps to the 10P/2B PAF lost start of fragment
register."
REFERENCE
"[802.3ah] 45.2.3.27"
::= { efmCuPortStatusEntry 9 }
efmCuPAFInLostEnds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A number of missing EndOfPacket indicators expected by the
frame assembly function.
This read-only counter is inactive when the PAF is
unsupported or disabled. Upon disabling the PAF, the counter
retains its previous value.
If a Clause 45 MDIO Interface to the PCS is present, then
this object maps to the 10P/2B PAF lost start of fragment
register."
REFERENCE
"[802.3ah] 45.2.3.28"
::= { efmCuPortStatusEntry 10 }
efmCuPAFInOverflows OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A number of fragements, received accross the gamma interface
and discarded, which would have caused the frame assembly
buffer to overflow.
This read-only counter is inactive when the PAF is
unsupported or disabled. Upon disabling the PAF, the counter
Beili Expires April 27, 2006 [Page 29]
Internet-Draft EFMCu Interfaces MIB October 2005
retains its previous value.
If a Clause 45 MDIO Interface to the PCS is present, then
this object maps to the 10P/2B PAF overflow register."
REFERENCE
"[802.3ah] 45.2.3.24"
::= { efmCuPortStatusEntry 11 }
-- PME Notifications Group
efmCuPmeNotifications OBJECT IDENTIFIER ::= { efmCuPme 0 }
-- EdNote: Should I add more notifications here, for example
-- efmCuPmePerfES,
-- efmCuPmePerfSES,
-- efmCuPmePerfCRCanomalies,
-- efmCuPmePerfLOSWS,
-- efmCuPmePerfUAS,
-- efmCuPmeDeviceFault,
-- efmCuPmeLocalPowerLoss
-- Another option would be to reference HDSL2-SHDSL-LINE-MIB
-- or VDSL-LINE-EXT-MCM-MIB, reusing notifications defined there.
efmCuPmeLineAtnCrossing NOTIFICATION-TYPE
OBJECTS {
efmCuPmeLineAtn,
efmCuPmeThreshLineAtn
}
STATUS current
DESCRIPTION
"This notification indicates that the loop attenuation
threshold (as per the efmCuPmeThreshLineAtn
value) has been reached/exceeded for the 2BASE-TL/10PASS-TS
PME. This notification MAY be send on the crossing event in
both directions: from normal to exceeded and from exceeded
to normal.
Generation of this notification is controlled by the
efmCuPmeLineAtnCrossingEnable object."
-- EdNote: add throttling limitations here, with 10 sec
-- debouncing on clear to prevenmt intermittent alarms
::= { efmCuPmeNotifications 1 }
efmCuPmeSnrMgnCrossing NOTIFICATION-TYPE
OBJECTS {
efmCuPmeSnrMgn,
efmCuPmeThreshSnrMgn
}
Beili Expires April 27, 2006 [Page 30]
Internet-Draft EFMCu Interfaces MIB October 2005
STATUS current
DESCRIPTION
"This notification indicates that the SNR margin threshold
(as per the efmCuPmeThreshSnrMgn value) has been
reached/exceeded for the 2BASE-TL/10PASS-TS PME.
This notification MAY be send on the crossing event in
both directions: from normal to exceeded and from exceeded
to normal.
Generation of this notification is controlled by the
efmCuPmeSnrMgnCrossingEnable object."
-- EdNote: add throttling limitations here, with 10 sec
-- debouncing on clear to prevenmt intermittent alarms
::= { efmCuPmeNotifications 2 }
efmCuPmeDeviceFault NOTIFICATION-TYPE
OBJECTS {
efmCuPmeFltStatus
}
STATUS current
DESCRIPTION
"This notification indicates that a fault in the PME has been
detected by a vendor specific diagnostic or a self-test.
Generation of this notification is controlled by the
efmCuPmeDeviceFaultEnable object."
::= { efmCuPmeNotifications 3 }
efmCuPmeConfigInitFailure NOTIFICATION-TYPE
OBJECTS {
efmCuPmeFltStatus,
efmCuAdminProfile,
efmCuPmeAdminProfile
}
STATUS current
DESCRIPTION
"This notification indicates that PME initialization has
failed, due to inability of the PME link to achieve requested
configuration profile.
Generation of this notification is controlled by the
efmCuPmeConfigInitFailEnable object."
::= { efmCuPmeNotifications 4 }
efmCuPmeProtocolInitFailure NOTIFICATION-TYPE
OBJECTS {
efmCuPmeFltStatus,
efmCuPmeOperSubType
Beili Expires April 27, 2006 [Page 31]
Internet-Draft EFMCu Interfaces MIB October 2005
}
STATUS current
DESCRIPTION
"This notification indicates that peer PME was using
incompatible protocol during initialization.
Generation of this notification is controlled by the
efmCuPmeProtocolInitFailEnable object."
::= { efmCuPmeNotifications 5 }
-- The PME group
efmCuPmeConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF EfmCuPmeConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table for Configuration of common aspects for EFMCu
2BASE-TL/10PASS-TS PME ports (modems). Configuration of
aspects specific to 2BASE-TL or 10PASS-TS PME types is
represented in efmCuPme2BConfTable and efmCuPme10PConfTable
respectively.
Entries in this table MUST be maintained in a persistent
manner."
::= { efmCuPme 1 }
efmCuPmeConfEntry OBJECT-TYPE
SYNTAX EfmCuPmeConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the EFMCu PME Configuration table.
Each entry represents common aspects of an EFMCu PME port
indexed by the ifIndex. Note that an EFMCu PME port can be
stacked below a single PCS port, also indexed by ifIndex,
possibly together with other PME ports if PAF is enabled."
INDEX { ifIndex }
::= { efmCuPmeConfTable 1 }
EfmCuPmeConfEntry ::=
SEQUENCE {
efmCuPmeAdminSubType INTEGER,
efmCuPmeAdminProfile ProfileIndexOrZero,
efmCuPAFRemoteDiscoveryCode PhysAddress,
efmCuPmeThreshLineAtn Integer32,
efmCuPmeThreshSnrMgn Integer32,
efmCuPmeLineAtnCrossingEnable TruthValue,
Beili Expires April 27, 2006 [Page 32]
Internet-Draft EFMCu Interfaces MIB October 2005
efmCuPmeSnrMgnCrossingEnable TruthValue,
efmCuPmeDeviceFaultEnable TruthValue,
efmCuPmeConfigInitFailEnable TruthValue,
efmCuPmeProtocolInitFailEnable TruthValue
}
efmCuPmeAdminSubType OBJECT-TYPE
SYNTAX INTEGER {
ieee2BaseTLO(1),
ieee2BaseTLR(2),
ieee10PassTSO(3),
ieee10PassTSR(4),
ieee2BaseTLor10PassTSR(5),
ieee2BaseTLor10PassTSO(6),
ieee10PassTSor2BaseTLO(7)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administrative (desired) sub-type of the PME.
Possible values are:
ieee2BaseTLO - PME shall operate as 2BaseTL-O
ieee2BaseTLR - PME shall operate as 2BaseTL-R
ieee10PassTSO - PME shall operate as 10PassTS-O
ieee10PassTSR - PME shall operate as 10PassTS-R
ieee2BaseTLor10PassTSR - PME shall operate as 2BaseTL-R or
10PassTS-R. Actual value will be
set by -O link partner during
initialization (handshake).
ieee2BaseTLor10PassTSO - PME shall operate as 2BaseTL-O
(preferred) or 10PassTS-O. Actual
value will be set during
initialization depending on -R
link partner capability (i.e. if
-R is incapable of the preferred
2BaseTL mode, 10PassTS will be
used).
ieee10PassTSor2BaseTLO - PME shall operate as 10PassTS-O
(preferred) or 2BaseTL-O. Actual
value will be set during
initialization depending on -R
link partner capability (i.e. if
-R is incapable of the preferred
10PassTS mode, 2BaseTL will be
used).
Changing efmCuPmeAdminSubType is a traffic disruptive
operation and as such SHALL be done when the link is Down.
Beili Expires April 27, 2006 [Page 33]
Internet-Draft EFMCu Interfaces MIB October 2005
Attempts to change this object SHALL be ignored if the link
is Up or Initializing.
Attempts to change this object to an unsupported subtype
(see efmCuPmeSubTypesSupported) SHALL be rejected.
The current operational sub type is indicated by
efmCuPmeOperSubType variable.
If a Clause 45 MDIO Interface to the PMA/PMD is present, then
this object combines values of the Port sub-type select
bits and the PMA/PMD type selection bits in the 10P/2B
PMA/PMD control register"
REFERENCE
"[802.3ah] 61.1, 45.2.1.11.4, 45.2.1.11.7"
::= { efmCuPmeConfEntry 1 }
efmCuPmeAdminProfile OBJECT-TYPE
SYNTAX ProfileIndexOrZero
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Desired PME configuration Profile. This object is a pointer
to an entry in either efmCuPme2BProfileTable or
efmCuPme10PProfileTable, depending on the current
operating SubType of the PME. The value of this object is the
index of the referenced profile.
The value of zero (default) indicates that the PME is
configured via efmCuAdminProfile object for the PCS port,
to which this PME is assigned. That is, the profile referenced
by efmCuPmeAdminProfile takes precedence over the profile(s)
referenced by efmCuAdminProfile.
This object is writable and readable for the CO subtype PMEs
(2BaseTL-O or 10PassTS-O). It is unavailable for the CPE
subtype (2BaseTL-R or 10PassTS-R).
Note that current operational Profile value is available via
efmCuPmeOperProfile object.
Modification of this object must be performed when the link is
Down. Attempts to change this object MUST be rejected, if the
link is Up or Initializing.
Attempts to set this object to a value that is not the
value of the index for an active entry in the corresponding
profile table, MUST be rejected."
REFERENCE
"[802.3ah] 30.11.2.1.6"
DEFVAL { 0 }
Beili Expires April 27, 2006 [Page 34]
Internet-Draft EFMCu Interfaces MIB October 2005
::= { efmCuPmeConfEntry 2 }
efmCuPAFRemoteDiscoveryCode OBJECT-TYPE
SYNTAX PhysAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"PAF Remote Discovery Code of the PME port at CO.
A 6 Byte long Discovery Code of the peer PCS connected via
the PME.
Reading this object results in a Discovery Get operation.
Writing a zero to this object results in a Discovery
Clear_if_Same operation (the value of efmCuPAFDiscoveryCode
at the peer PCS shall be the same as efmCuPAFDiscoveryCode of
the local PCS associated with the PME for the operation to
succeed).
Writing a non-zero value to this object results in a
Discovery Set_if_Clear operation.
This object does not exist in CPE port subtypes. A zero length
octet string SHALL be returned for CPE port subtypes and also
when PAF aggregation is not enabled.
Discovery MUST be performed when the link is Down.
Attempts to change this object MUST be rejected with the error
inconsistentValue, if the link is Up or Initializing.
If a Clause 45 MDIO Interface to the PMA/PMD is present, then
this object is a function of 10P/2B aggregation discovery
control register, Discovery operation result bits in 10P/2B
aggregation and discovery status register and
10P/2B aggregation discovery code register"
REFERENCE
"[802.3ah] 61.2.2.8.4, 45.2.6.6-45.2.6.8"
::= { efmCuPmeConfEntry 3 }
efmCuPmeThreshLineAtn OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Desired Line Attenuation Threshold for the 2B/10P PME.
This object configures the line attenuation alarm threshold.
When the current value of Line Attenuation reaches or
exceeds this threshold, a efmCuPmeLineAtnCrossing
notification MAY be generated, if enabled by
efmCuPmeLineAtnCrossingEnable.
Beili Expires April 27, 2006 [Page 35]
Internet-Draft EFMCu Interfaces MIB October 2005
This object is writable for the CO subtype PMEs (-O).
It is read-only for the CPE subtype (-R).
Changing of the Line Attenuation Threshold must be performed
when the link is Down. Attempts to change this object MUST be
rejected with the error inconsistentValue, if the link is Up
or Initializing.
If a Clause 45 MDIO Interface to the PME is present, then this
object will map to the Loop attenuation threshold bits in
the 2B PMD line quality thresholds register"
REFERENCE
"[802.3ah] 45.2.1.36"
::= { efmCuPmeConfEntry 4 }
efmCuPmeThreshSnrMgn OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Desired SNR Margin Threshold for the 2B/10P PME.
This object configures the SNR margin alarm threshold.
When the current value of SNR Margin reaches
or exceeds this threshold, a efmCuPmeSnrMgnCrossing
notification MAY be generated, if enabled by
efmCuPmeSnrMgnCrossingEnable.
This object is writable for the CO subtype PMEs
(2BaseTL-O/10PassTS-R). It is read-only for the CPE subtype
(2BaseTL-R/10PassTS-R).
Changing of the SNR Margin Threshold must be performed when
the link is Down. Attempts to change this object MUST be
rejected with the error inconsistentValue, if the link is Up
or Initializing.
If a Clause 45 MDIO Interface to the PME is present, then this
object will map to the SNR margin threshold bits in the
2B PMD line quality thresholds register"
REFERENCE
"[802.3ah] 45.2.1.36"
::= { efmCuPmeConfEntry 5 }
efmCuPmeLineAtnCrossingEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
Beili Expires April 27, 2006 [Page 36]
Internet-Draft EFMCu Interfaces MIB October 2005
DESCRIPTION
"Indicates whether efmCuPmeLineAtnCrossing notifications
should be generated for this interface.
Value of true(1) indicates that efmCuPmeLineAtnCrossing
notification is enabled. Value of false(2) indicates that
the notification is disabled."
::= { efmCuPmeConfEntry 6 }
efmCuPmeSnrMgnCrossingEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether efmCuPmeSnrMgnCrossing notifications
should be generated for this interface.
Value of true(1) indicates that efmCuPmeSnrMgnCrossing
notification is enabled. Value of false(2) indicates that
the notification is disabled."
::= { efmCuPmeConfEntry 7 }
efmCuPmeDeviceFaultEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether efmCuPmeDeviceFault notifications
should be generated for this interface.
Value of true(1) indicates that efmCuPmeDeviceFault
notification is enabled. Value of false(2) indicates that
the notification is disabled."
::= { efmCuPmeConfEntry 8 }
efmCuPmeConfigInitFailEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether efmCuPmeConfigInitFailure notifications
should be generated for this interface.
Value of true(1) indicates that efmCuPmeConfigInitFailure
notification is enabled. Value of false(2) indicates that
the notification is disabled."
::= { efmCuPmeConfEntry 9 }
Beili Expires April 27, 2006 [Page 37]
Internet-Draft EFMCu Interfaces MIB October 2005
efmCuPmeProtocolInitFailEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether efmCuPmeProtocolInitFailure notifications
should be generated for this interface.
Value of true(1) indicates that efmCuPmeProtocolInitFailure
notification is enabled. Value of false(2) indicates that
the notification is disabled."
::= { efmCuPmeConfEntry 10 }
efmCuPmeCapabilityTable OBJECT-TYPE
SYNTAX SEQUENCE OF EfmCuPmeCapabilityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table for Configuration of common aspects for EFMCu
2BASE-TL/10PASS-TS PME ports (modems). Configuration of
aspects specific to 2BASE-TL or 10PASS-TS PME types is
represented in efmCuPme2BConfTable and efmCuPme10PConfTable
respectively.
Entries in this table MUST be maintained in a persistent
manner."
::= { efmCuPme 2 }
efmCuPmeCapabilityEntry OBJECT-TYPE
SYNTAX EfmCuPmeCapabilityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the EFMCu PME Capability table.
Each entry represents common aspects of an EFMCu PME port
indexed by the ifIndex. Note that an EFMCu PME port can be
stacked below a single PCS port, also indexed by ifIndex,
possibly together with other PME ports if PAF is enabled."
INDEX { ifIndex }
::= { efmCuPmeCapabilityTable 1 }
EfmCuPmeCapabilityEntry ::=
SEQUENCE {
efmCuPmeSubTypesSupported BITS
}
efmCuPmeSubTypesSupported OBJECT-TYPE
Beili Expires April 27, 2006 [Page 38]
Internet-Draft EFMCu Interfaces MIB October 2005
SYNTAX BITS {
ieee2BaseTLO(0),
ieee2BaseTLR(1),
ieee10PassTSO(2),
ieee10PassTSR(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"PME supported sub-types. This is a bitmap of possible
sub-types. The various bit positions are:
ieee2BaseTLO - PME is capable of operating as 2BaseTL-O
ieee2BaseTLR - PME is capable of operating as 2BaseTL-R
ieee10PassTSO - PME is capable of operating as 10PassTS-O
ieee10PassTSR - PME is capable of operating as 10PassTS-R
An desired mode of operation is determined by
efmCuPmeAdminSubType, while efmCuPmeOperSubType relects the
current operating mode.
If a Clause 45 MDIO Interface to the PCS is present, then this
object combines the 10PASS-TS capable and 2BASE-TL capable
bits in the 10P/2B PMA/PMD speed ability register and the
CO supported and CPE supported bits in the 10P/2B PMA/PMD
status register"
REFERENCE
"[802.3ah] 61.1, 45.2.1.4.1, 45.2.1.4.2, 45.2.1.12.2,
45.2.1.12.3"
::= { efmCuPmeCapabilityEntry 1 }
efmCuPmeStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF EfmCuPmeStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides common status information of EFMCu
2BASE-TL/10PASS-TS PME ports. Status information specific
to 10PASS-TS PME is represented in efmCuPme10PStatusTable.
This table contains live data from the equipment. As such,
it is NOT persistent."
::= { efmCuPme 3 }
efmCuPmeStatusEntry OBJECT-TYPE
SYNTAX EfmCuPmeStatusEntry
MAX-ACCESS not-accessible
STATUS current
Beili Expires April 27, 2006 [Page 39]
Internet-Draft EFMCu Interfaces MIB October 2005
DESCRIPTION
"An entry in the EFMCu PME Status table.
Each entry represents common aspects of an EFMCu PME port
indexed by the ifIndex. Note that an EFMCu PME port can be
stacked below a single PCS port, also indexed by ifIndex,
possibly together with other PME ports if PAF is enabled."
INDEX { ifIndex }
::= { efmCuPmeStatusTable 1 }
EfmCuPmeStatusEntry ::=
SEQUENCE {
efmCuPmeOperStatus INTEGER,
efmCuPmeFltStatus BITS,
efmCuPmeOperSubType INTEGER,
efmCuPmeOperProfile ProfileIndexOrZero,
efmCuPmeSnrMgn Integer32,
efmCuPmePeerSnrMgn Integer32,
efmCuPmeLineAtn Integer32,
efmCuPmePeerLineAtn Integer32,
efmCuPmeTCCodingErrors Counter32,
efmCuPmeTCCrcErrors Counter32
}
efmCuPmeOperStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
downNotReady(2),
downReady(3),
init(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current PME link Operational Status. Possible values are:
up(1) - link is Up and ready to pass 64/65B
encoded frames or fragments.
downNotReady(2) - link is Down and the PME does not detect
Handshake tones from its peer. This value
may indicate a possible problem with
the peer PME.
downReady(3) - link is Down and the PME detects Handshake
tones from its peer.
init(4) - link is initializing, as a result of
ifAdminStatus being set to 'up' for a
particular PME or a PCS the PME is
connected to.
This object is intended to supplement Down state of
Beili Expires April 27, 2006 [Page 40]
Internet-Draft EFMCu Interfaces MIB October 2005
ifOperStatus.
This object partially maps to the Clause 30 attribute
aPMEStatus.
If a Clause 45 MDIO Interface to the PME is present, then this
object partially maps to PMA/PMD link status bits in 10P/2B
PMA/PMD status register."
REFERENCE
"[802.3ah] 30.11.2.1.3, 45.2.1.12.4"
::= { efmCuPmeStatusEntry 1 }
efmCuPmeFltStatus OBJECT-TYPE
SYNTAX BITS {
lossOfFraming(0),
snrMgnDefect(1),
lineAtnDefect(2),
deviceFault(3),
configInitFailure(4),
protocolInitFailure(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current/Last PME link Fault Status. This is a bitmap of
possible conditions. The various bit positions are:
lossOfFraming - Loss of Framing for 10P or
Loss of Sync word for 2B PMD or
Loss of 64/65B Framing
snrMgnDefect - SNR Margin dropped below the Threshold
lineAtnDefect - Line Attenuation exceeds the Threshold
deviceFault - Indicates a vendor-dependent
diagnostic or self-test fault
has been detected.
configInitFailure - Configuration initialization failure,
due to inability of the PME link to
support configuration profile,
requested during initialization.
protocolInitFailure - Protocol initialization failure,
due to incompatible protocol used by
the Peer PME during init (that could
happen if a peer PMD is G.SDHSL/VDSL
modem for 2BASE-TL/10PASS-TS PME
respectively).
This object is intended to supplement ifOperStatus in IF-MIB.
Beili Expires April 27, 2006 [Page 41]
Internet-Draft EFMCu Interfaces MIB October 2005
The indications hold information about the last fault.
efmCuPmeFltStatus is cleared by the device restart.
In addition lossOfFraming, configInitFailure and
protocolInitFailure are cleared by PME init.
deviceFault is cleared by successful diagnostics/test.
snrMgnDefect and lineAtnDefect are cleared by SNR Margin
and line Attenuation respectively returning to norm and by
PME init.
This object partially maps to the Clause 30 attribute
aPMEStatus.
If a Clause 45 MDIO Interface to the PME is present, then this
object consolidates information from various PMA/PMD
registers, namely: Fault bit in PMA/PMD status 1 register,
10P/2B PMA/PMD link loss register,
10P outgoing indicator bits status register,
10P incoming indicator bits status register,
2B state defects register."
REFERENCE
"[802.3ah] 30.11.2.1.3, 45.2.1.2.1, 45.2.1.38,
45.2.1.39, 45.2.1.54"
::= { efmCuPmeStatusEntry 2 }
efmCuPmeOperSubType OBJECT-TYPE
SYNTAX INTEGER {
ieee2BaseTLO(1),
ieee2BaseTLR(2),
ieee10PassTSO(3),
ieee10PassTSR(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current operational sub-type of the PME.
Possible values are:
ieee2BaseTLO - PME operates as 2BaseTL-O
ieee2BaseTLR - PME operates as 2BaseTL-R
ieee10PassTSO - PME operates as 10PassTS-O
ieee10PassTSR - PME operates as 10PassTS-R
The operational sub type of the PME can be configured via
efmCuPmeAdminSubType variable.
If a Clause 45 MDIO Interface to the PMA/PMD is present, then
this object combines values of the Port sub-type select
bits, the PMA/PMD type selection bits in the 10P/2B
PMA/PMD control register and the PMA/PMD link status bits in
Beili Expires April 27, 2006 [Page 42]
Internet-Draft EFMCu Interfaces MIB October 2005
the 10P/2B PMA/PMD status register."
REFERENCE
"[802.3ah] 61.1, 45.2.1.11.4, 45.2.1.11.7, 45.2.1.12.4"
::= { efmCuPmeStatusEntry 3 }
efmCuPmeOperProfile OBJECT-TYPE
SYNTAX ProfileIndexOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"PME current operating Profile. This object is a pointer to
an entry in either efmCuPme2BProfileTable or
efmCuPme10PProfileTable, depending on the current
operating SubType of the PME as indicated by
efmCuPmeOperSubType.
Note that a profile entry, to which efmCuPmeOperProfile is
pointing to, can be created automatically, to reflect achieved
parameters in adaptive (not fixed) initialization,
i.e. values of efmCuPmeOperProfile and efmCuAdminProfile or
efmCuPmeAdminProfile MAY differ.
The value of zero indicates that PME is down or initializing.
This object partially maps to the aOperatingProfile
attribute in Clause 30."
REFERENCE
"[802.3ah] 30.11.2.1.7"
::= { efmCuPmeStatusEntry 4 }
efmCuPmeSnrMgn OBJECT-TYPE
SYNTAX Integer32(-127..128|65535)
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current Signal-to-Noise Ratio (SNR) margin with respect
to the received signal as perceived by the local PME.
The value of 65535 is returned when PME is down or
initializing.
This object maps to the aPMESNRMgn attribute in Clause 30.
If a Clause 45 MDIO Interface is present, then this
object maps to the 10P/2B RX SNR margin register."
REFERENCE
"[802.3ah] 30.11.2.1.4, 45.2.1.16"
::= { efmCuPmeStatusEntry 5 }
efmCuPmePeerSnrMgn OBJECT-TYPE
Beili Expires April 27, 2006 [Page 43]
Internet-Draft EFMCu Interfaces MIB October 2005
SYNTAX Integer32(-127..128|65535)
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current SNR margin in dB with respect to the received
signal, as perceived by the remote (link partner) PME.
The value of 65535 is returned when PME is down or
initializing.
This object is not supported by -R PME subtypes.
If a Clause 45 MDIO Interface is present, then this
object maps to the 10P/2B link partner RX SNR margin
register."
REFERENCE
"[802.3ah] 45.2.1.17"
::= { efmCuPmeStatusEntry 6}
efmCuPmeLineAtn OBJECT-TYPE
SYNTAX Integer32(-127..128|65535)
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current Line Attenuation in dB as perceived by the local
PME.
The value of 65535 is returned when PME is down or
initializing.
If a Clause 45 MDIO Interface is present, then this
object maps to the Line Attenuation register"
REFERENCE
"[802.3ah] 45.2.1.18"
::= { efmCuPmeStatusEntry 7 }
efmCuPmePeerLineAtn OBJECT-TYPE
SYNTAX Integer32(-127..128|65535)
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current Line Attenuation in dB as perceived by the remote
(link partner) PME.
The value of 65535 is returned when PME is down or
initializing.
This object is not supported by CPE port subtypes.
Beili Expires April 27, 2006 [Page 44]
Internet-Draft EFMCu Interfaces MIB October 2005
If a Clause 45 MDIO Interface is present, then this
object maps to the 20P/2B link partner Line Attenuation
register."
REFERENCE
"[802.3ah] 45.2.1.19"
::= { efmCuPmeStatusEntry 8 }
efmCuPmeTCCodingErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A number of 64/65-octet encapsulation errors. This counter is
incremented for each 64/65-octet encapsulation error detected
by the 64/65-octet receive function.
The value of zero SHALL be returned when PME is down or
initializing.
If a Clause 45 MDIO Interface to the PME TC is present, then
this object maps to the TC coding violations register
(see 45.2.6.12)."
REFERENCE
"[802.3ah] 61.3.3.1, 45.2.6.12"
::= { efmCuPmeStatusEntry 9 }
efmCuPmeTCCrcErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A number of TC-CRC errors. This counter is incremented for
each TC-CRC error detected by the 64/65-octet receive function
(see 61.3.3.3 and Figure 61-19).
The value of zero SHALL be returned when PME is down or
initializing.
If a Clause 45 MDIO Interface to the PCME TC is present, then
this object maps to the TC CRC error register
(see 45.2.6.11)."
REFERENCE
"[802.3ah] 61.3.3.3, 45.2.6.11"
::= { efmCuPmeStatusEntry 10 }
-- 2BASE-TL specific PME group
efmCuPme2B OBJECT IDENTIFIER ::= { efmCuPme 5 }
efmCuPme2BProfileTable OBJECT-TYPE
Beili Expires April 27, 2006 [Page 45]
Internet-Draft EFMCu Interfaces MIB October 2005
SYNTAX SEQUENCE OF EfmCuPme2BProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports definitions of administrative and
operating Profiles for 2BASE-TL PMEs.
First 14 entries in this table SHALL always be defined as
follows (see 802.3ah Annex 63A):
-------+------+-----+--------+------------------
Profile Rate Power Region Constellation
index (Kbps) (dBm) (G.991.2)
-------+------+-----+--------+------------------
1 5696 13.5 1 32-TCPAM (default)
2 3072 13.5 1 32-TCPAM
3 2048 13.5 1 16-TCPAM
4 1024 13.5 1 16-TCPAM
5 704 13.5 1 16-TCPAM
6 512 13.5 1 16-TCPAM
7 5696 14.5 2 32-TCPAM
8 3072 14.5 2 32-TCPAM
9 2048 14.5 2 16-TCPAM
10 1024 13.5 2 16-TCPAM
11 704 13.5 2 16-TCPAM
12 512 13.5 2 16-TCPAM
13 0 0 1 0 (best effort)
14 0 0 2 0 (best effort)
These default entries SHALL be created during agent
initialization and MUST not be deleted.
Entries following the first 14, can be dynamically created and
deleted, to provide custom administrative (configuration)
profiles and automatic operating profiles.
This table MUST be maintained in a persistent manner."
REFERENCE
"[802.3ah] Annex 63A, 30.11.2.1.6"
::= { efmCuPme2B 2 }
efmCuPme2BProfileEntry OBJECT-TYPE
SYNTAX EfmCuPme2BProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry corresponds to a single 2BASE-TL PME profile.
Each profile contains a set of parameters, used either for
configuration or representation of a 2BASE-TL PME.
In case a particular profile is referenced via
Beili Expires April 27, 2006 [Page 46]
Internet-Draft EFMCu Interfaces MIB October 2005
efmCuPmeAdminProfile object (or efmCuAdminProfile if
efmCuPmeAdminProfile is zero), it represent the desired
parameters the 2BaseTL-O PME initialization.
If a profile is referenced via efmCuPmeOperProfile object,
it represents current operating parameters of the
operational PME.
Profiles may be created/deleted using the row creation/
deletion mechanism via efmCuPme2BProfileRowStatus. If an
active entry is referenced, the entry MUST remain 'active'
until all references are removed.
Default entries MUST not be removed."
INDEX { efmCuPme2BProfileIndex }
::= { efmCuPme2BProfileTable 1 }
EfmCuPme2BProfileEntry ::=
SEQUENCE {
efmCuPme2BProfileIndex ProfileIndex,
efmCuPme2BProfileDescr SnmpAdminString,
efmCuPme2BRegion INTEGER,
efmCuPme2BDataRate Unsigned32,
efmCuPme2BPower Unsigned32,
efmCuPme2BConstellation INTEGER,
efmCuPme2BProfileRowStatus RowStatus
}
efmCuPme2BProfileIndex OBJECT-TYPE
SYNTAX ProfileIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"2BASE-TL PME Profile index.
This object is the unique index associated with this profile.
Entries in this table are referenced via efmCuAdminProfile
or efmCuPmeAdminProfile objects."
::= { efmCuPme2BProfileEntry 1 }
efmCuPme2BProfileDescr OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..255))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A textual string containing information about 2BASE-TL PME
Profile. The string MAY include information about data rate
and spectral limitations of this particular profile."
::= { efmCuPme2BProfileEntry 2 }
efmCuPme2BRegion OBJECT-TYPE
Beili Expires April 27, 2006 [Page 47]
Internet-Draft EFMCu Interfaces MIB October 2005
SYNTAX INTEGER {
region1(1),
region2(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Power Spectral Density (PSD) Regional settings as
specified in the relevant Regional Annex of [G.991.2].
Regional settings place limitations on the max allowed
data rate, power and constellation.
Possible values for this object are:
region1 -- Annexes A and F (e.g. North America)
region2 -- Annexes B and G (e.g. Europe)
Changing of the Region must be performed when the link is
Down.
Attempts to change this object MUST be rejected with
the error inconsistentValue, if the link is Up or
Initializing.
If a Clause 45 MDIO Interface to the PME is present, then this
object maps to the Region bits in the 2B general
parameter register."
REFERENCE
"[802.3ah] 45.2.1.42"
::= { efmCuPme2BProfileEntry 3 }
efmCuPme2BDataRate OBJECT-TYPE
SYNTAX Unsigned32(0..5696)
UNITS "Kbps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"2BASE-TL PME Data Rate.
The rate is fixed when the value of this object is n x 64Kbps,
where n=3..60 for 16-TCPAM and n=12..89 for 32-TCPAM.
The value of 0 in the administrative profile means that data
rate is not fixed but is adaptive and should be set to the
maximum attainable rate during line probing, under the
spectral limitations placed by the efmCuPme2BRegion.
If a Clause 45 MDIO Interface to the PME is present, then this
object maps to the Min/Max Data Rate1 bits in the 2B PMD
parameters register.
This object MUST be maintained in a persistent manner."
Beili Expires April 27, 2006 [Page 48]
Internet-Draft EFMCu Interfaces MIB October 2005
REFERENCE
"[802.3ah] 45.2.1.43"
::= { efmCuPme2BProfileEntry 4 }
efmCuPme2BPower OBJECT-TYPE
SYNTAX Unsigned32(0|10..42)
UNITS "0.5 dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Signal Transmit Power. Multiple of 0.5dBm.
The value of 0 in the administrative profile means that the
signal transmit power is not fixed and should be set to
maximize the attainable rate, under the spectral limitations
placed by the efmCuPme2BRegion.
Changing of the Signal Transmit Power must be performed when
the link is Down. Attempts to change this object MUST be
rejected with the error inconsistentValue, if the link is Up
or Initializing.
If a Clause 45 MDIO Interface to the PME is present, then this
object will map to the Power1 bits in the 2B PMD
parameters register"
REFERENCE
"[802.3ah] 45.2.1.43"
::= { efmCuPme2BProfileEntry 5 }
efmCuPme2BConstellation OBJECT-TYPE
SYNTAX INTEGER {
adaptive(0),
tcpam16(1),
tcpam32(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"TCPAM Constellation of the 2BASE-TL PME.
The possible values are:
adaptive(0) - either 16- or 32-TCPAM
tcpam16(1) - 16-TCPAM
tcpam32(2) - 32-TCPAM
The value of adaptive(0) in the administrative profile means
that the constellation is not fixed and should be set to
maximize the attainable rate, under the spectral limitations
placed by the efmCuPme2BRegion.
Beili Expires April 27, 2006 [Page 49]
Internet-Draft EFMCu Interfaces MIB October 2005
If a Clause 45 MDIO Interface to the PME is present, then this
object map to the Constellation1 bits in the 2B general
parameter register."
REFERENCE
"[802.3ah] 45.2.1.43"
::= { efmCuPme2BProfileEntry 6 }
efmCuPme2BProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object controls creation/deletion of the associated
entry in efmCuPme2BProfileTable per the semantics of
RowStatus.
If an 'active' entry is referenced via efmCuAdminProfile or
efmCuPmeAdminProfile, the entry MUST remain 'active' until all
references are removed."
::= { efmCuPme2BProfileEntry 7 }
-- 10PASS-TS specific PME group
efmCuPme10P OBJECT IDENTIFIER ::= { efmCuPme 6 }
efmCuPme10PProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF EfmCuPme10PProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports definitions of configuration profiles for
10PassTL PMEs.
First 22 entries in this table SHALL always be defined as
follows (see 802.3ah Annex 62B.3):
-------+--------+----+---------+-----+------------
Profile Bandplan UPBO BandNotch DRate URate
Index PSDMask# p# p# p# p#
-------+--------+----+---------+-----+------------
1 1 3 2,6,10,11 20 20(default)
2 13 5 0 20 20
3 1 1 0 20 20
4 16 0 0 100 100
5 16 0 0 70 50
6 6 0 0 50 10
7 17 0 0 30 30
8 8 0 0 30 5
9 4 0 0 25 25
10 4 0 0 15 15
11 23 0 0 10 10
Beili Expires April 27, 2006 [Page 50]
Internet-Draft EFMCu Interfaces MIB October 2005
12 23 0 0 5 5
13 16 0 2,5,9,11 100 100
14 16 0 2,5,9,11 70 50
15 6 0 2,6,10,11 50 10
16 17 0 2,5,9,11 30 30
17 8 0 2,6,10,11 30 5
18 4 0 2,6,10,11 25 25
19 4 0 2,6,10,11 15 15
20 23 0 2,5,9,11 10 10
21 23 0 2,5,9,11 5 5
22 30 0 0 200 50
These default entries SHALL be created by during agent
initialization and MUST not be deleted.
Entries following the first 22, can be dynamically created and
deleted, to provide custom administrative (configuration)
profiles and automatic operating profiles.
This table MUST be maintained in a persistent manner."
REFERENCE
"[802.3ah] Annex 62B.3, 30.11.2.1.6"
::= { efmCuPme10P 1 }
efmCuPme10PProfileEntry OBJECT-TYPE
SYNTAX EfmCuPme10PProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry corresponds to a single 10PASS-TS PME
profile.
Each profile contains a set of parameters, used either for
configuration or representation of a 10PASS-TS PME.
In case a particular profile is referenced via
efmCuPmeAdminProfile object (or efmCuAdminProfile if
efmCuPmeAdminProfile is zero), it represent the desired
parameters the 10PassTS-O PME initialization.
If a profile is referenced via efmCuPmeOperProfile object,
it represents current operating parameters of the PME.
Profiles may be created/deleted using the row creation/
deletion mechanism via efmCuPme10PProfileRowStatus. If an
'active' entry is referenced, the entry MUST remain 'active'
until all references are removed.
Default entries MUST not be removed."
INDEX { efmCuPme10PProfileIndex }
::= { efmCuPme10PProfileTable 1 }
Beili Expires April 27, 2006 [Page 51]
Internet-Draft EFMCu Interfaces MIB October 2005
EfmCuPme10PProfileEntry ::=
SEQUENCE {
efmCuPme10PProfileIndex ProfileIndex,
efmCuPme10PProfileDescr SnmpAdminString,
efmCuPme10PBandplanPSDMskProfile INTEGER,
efmCuPme10PUPBOReferenceProfile INTEGER,
efmCuPme10PBandNotchProfiles BITS,
efmCuPme10PPayloadURateProfile INTEGER,
efmCuPme10PPayloadDRateProfile INTEGER,
efmCuPme10PProfileRowStatus RowStatus
}
efmCuPme10PProfileIndex OBJECT-TYPE
SYNTAX ProfileIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"10PASS-TS PME Profile Index.
This object is the unique index associated with this profile.
Entries in this table are referenced via efmCuAdminProfile or
efmCuPmeAdminProfile."
::= { efmCuPme10PProfileEntry 1 }
efmCuPme10PProfileDescr OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..255))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A textual string containing information about 10PASS-TS PME
Profile. The string MAY include information about data rate
and spectral limitations of this particular profile."
::= { efmCuPme10PProfileEntry 2 }
efmCuPme10PBandplanPSDMskProfile OBJECT-TYPE
SYNTAX INTEGER {
profile1(1),
profile2(2),
profile3(3),
profile4(4),
profile5(5),
profile6(6),
profile7(7),
profile8(8),
profile9(9),
profile10(10),
profile11(11),
profile12(12),
profile13(13),
Beili Expires April 27, 2006 [Page 52]
Internet-Draft EFMCu Interfaces MIB October 2005
profile14(14),
profile15(15),
profile16(16),
profile17(17),
profile18(18),
profile19(19),
profile20(20),
profile21(21),
profile22(22),
profile23(23),
profile24(24),
profile25(25),
profile26(26),
profile27(27),
profile28(28),
profile29(29)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"10PASS-TS PME Bandplan and PSD Mask profile,
as specified in 802.3ah Annex 62A. Possible values are:
--------------+------------------------+-----------+---------
Profile Name PSD Mask Bands Bandplan
--------------+------------------------+-----------+---------
profile1(1) - T1.424/T-U P1 FTTCab.M1 x/D/U/D/U A
profile2(2) - T1.424/T-U P1 FTTEx.M1
profile3(3) - T1.424/T-U P1 FTTCab.M2
profile4(4) - T1.424/T-U P1 FTTEx.M2
profile5(5) - T1.424/T-U P1 FTTCab.M1 D/D/U/D/U
profile6(6) - T1.424/T-U P1 FTTEx.M1
profile7(7) - T1.424/T-U P1 FTTCab.M2
profile8(8) - T1.424/T-U P1 FTTEx.M2
profile9(9) - T1.424/T-U P1 FTTCab.M1 U/D/U/D/x
profile10(10) - T1.424/T-U P1 FTTEx.M1
profile11(11) - T1.424/T-U P1 FTTCab.M2
profile12(12) - T1.424/T-U P1 FTTEx.M2
profile13(13) - TS1 101 270-1 Pcab.M1.A x/D/U/D/U B
profile14(14) - TS1 101 270-1 Pcab.M1.B
profile15(15) - TS1 101 270-1 Pex.P1.M1
profile16(16) - TS1 101 270-1 Pex.P2.M1
profile17(17) - TS1 101 270-1 Pcab.M2
profile18(18) - TS1 101 270-1 Pex.P1.M2
profile19(19) - TS1 101 270-1 Pex.P2.M2
profile20(20) - TS1 101 270-1 Pcab.M1.A U/D/U/D/x
profile21(21) - TS1 101 270-1 Pcab.M1.B
profile22(22) - TS1 101 270-1 Pex.P1.M1
profile23(23) - TS1 101 270-1 Pex.P2.M1
Beili Expires April 27, 2006 [Page 53]
Internet-Draft EFMCu Interfaces MIB October 2005
profile24(24) - TS1 101 270-1 Pcab.M2
profile25(25) - TS1 101 270-1 Pex.P1.M2
profile26(26) - TS1 101 270-1 Pex.P2.M2
profile27(27) - G.993.1 F.1.2.1 (VDSLoPOTS) x/D/U/D/U F
profile28(28) - G.993.1 F.1.2.2 (VDSLoTCM-ISDN)
profile29(29) - G.993.1 F.1.2.3 (PSD reduction)
This object maps to the aBandplanPSDMaskProfile attribute
in Clause 30."
REFERENCE
"[802.3ah] Annex 62A, 30.5.1.1.22"
::= { efmCuPme10PProfileEntry 3 }
efmCuPme10PUPBOReferenceProfile OBJECT-TYPE
SYNTAX INTEGER {
profile1(1),
profile2(2),
profile3(3),
profile4(4),
profile5(5),
profile6(6),
profile7(7),
profile8(8),
profile9(9)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"10PASS-TS PME Upstream Power Back-Off (UPBO) Reference PSD
Profile, as specified in 802.3ah Annex 62A. Possible values
are:
profile1(1) - T1.424/T-U Noise A M1
profile2(2) - T1.424/T-U Noise A M2
profile3(3) - T1.424/T-U Noise F M1
profile4(4) - T1.424/T-U Noise F M2
profile5(5) - ETSI TS 101 270-1 Noise A&B
profile6(6) - ETSI TS 101 270-1 Noise C
profile7(7) - ETSI TS 101 270-1 Noise D
profile8(8) - ETSI TS 101 270-1 Noise E
profile9(9) - ETSI TS 101 270-1 Noise F
This object maps to the aUPBOReferenceProfile attribute
in Clause 30."
REFERENCE
"[802.3ah] Annex 62A.3.4, 30.5.1.1.23"
::= { efmCuPme10PProfileEntry 4 }
efmCuPme10PBandNotchProfiles OBJECT-TYPE
Beili Expires April 27, 2006 [Page 54]
Internet-Draft EFMCu Interfaces MIB October 2005
SYNTAX BITS {
profile0(0),
profile1(1),
profile2(2),
profile3(3),
profile4(4),
profile5(5),
profile6(6),
profile7(7),
profile8(8),
profile9(9),
profile10(10),
profile11(11)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"10PASS-TS PME Egress Control Band Notch Profile bitmap,
as specified in 802.3ah Annex 62A. Possible values are:
--------------+---------+----------+-----------+------+-----
Profile Name G.991.3 T1.424/T-U TS101 270-1 StartF EndF
Table Table Table (MHz) (MHz)
--------------+---------+----------+-----------+------+-----
profile0(0) - no profile
profile1(1) - F-5 #01 - - 1.810 1.825
profile2(2) - 6-2 15-1 17 1.810 2.000
profile3(3) - F-5 #02 - - 1.907 1.912
profile4(4) - F-5 #03 - - 3.500 3.575
profile5(5) - 6-2 - 17 3.500 3.800
profile6(6) - - 15-1 - 3.500 4.000
profile7(7) - F-5 #04 - - 3.747 3.754
profile8(8) - F-5 #05 - - 3.791 3.805
profile9(9) - 6-2 - 17 7.000 7.100
profile10(10) - F-5 #06 15-1 - 7.000 7.300
profile11(11) - 6-2 15-1 1 10.100 10.150
Any combination of profiles can be specified by ORing
individual profiles, for example value of 0x0622 selects
profiles 2,6,10 and 11.
This object maps to the aBandNotchProfile attribute
in Clause 30."
REFERENCE
"[802.3ah] Annex 62A.3.5, 30.5.1.1.19"
::= { efmCuPme10PProfileEntry 5 }
efmCuPme10PPayloadURateProfile OBJECT-TYPE
SYNTAX INTEGER {
Beili Expires April 27, 2006 [Page 55]
Internet-Draft EFMCu Interfaces MIB October 2005
profile5(5),
profile10(10),
profile15(15),
profile20(20),
profile25(25),
profile30(30),
profile50(50),
profile70(70),
profile100(100)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"10PASS-TS PME Upstream Payload Rate Profile,
as specified in 802.3ah Annex 62A. Possible values are:
profile5(5) - 2.5 Mbps
profile10(10) - 5 Mbps
profile15(15) - 7.5 Mbps
profile20(20) - 10 Mbps
profile25(25) - 12.5 Mbps
profile30(30) - 15 Mbps
profile50(50) - 25 Mbps
profile70(70) - 35 Mbps
profile100(100) - 50 Mbps
Each value represents a target for the PME's Upstream Payload
Bitrate as seen at the MII. If the payload rate of the
selected profile cannot be achieved based on the loop
environment, bandplan and PSD mask, the PME initialization
SHALL fail.
This object maps to the aPayloadRateProfileUpstream
attribute in Clause 30."
REFERENCE
"[802.3ah] Annex 62A.3.6, 30.5.1.1.20"
::= { efmCuPme10PProfileEntry 6 }
efmCuPme10PPayloadDRateProfile OBJECT-TYPE
SYNTAX INTEGER {
profile5(5),
profile10(10),
profile15(15),
profile20(20),
profile25(25),
profile30(30),
profile50(50),
profile70(70),
profile100(100),
Beili Expires April 27, 2006 [Page 56]
Internet-Draft EFMCu Interfaces MIB October 2005
profile140(140),
profile200(200)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"10PASS-TS PME Downstream Payload Rate Profile,
as specified in 802.3ah Annex 62A. Possible values are:
profile5(5) - 2.5 Mbps
profile10(10) - 5 Mbps
profile15(15) - 7.5 Mbps
profile20(20) - 10 Mbps
profile25(25) - 12.5 Mbps
profile30(30) - 15 Mbps
profile50(50) - 25 Mbps
profile70(70) - 35 Mbps
profile100(100) - 50 Mbps
profile140(140) - 70 Mbps
profile200(200) - 100 Mbps
Each value represents a target for the PME's Downstream
Payload Bitrate as seen at the MII. If the payload rate of
the selected profile cannot be achieved based on the loop
environment, bandplan and PSD mask, the PME initialization
SHALL fail.
This object maps to the aPayloadRateProfileDownstream
attribute in Clause 30."
REFERENCE
"[802.3ah] Annex 62A.3.6, 30.5.1.1.21"
::= { efmCuPme10PProfileEntry 7 }
efmCuPme10PProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object controls creation/deletion of the associated
entry in efmCuPme10PProfileTable per the semantics of
RowStatus.
If an active entry is referenced via efmCuAdminProfile or
efmCuPmeAdminProfile, the entry MUST remain 'active' until
all references are removed."
::= { efmCuPme10PProfileEntry 8 }
efmCuPme10PStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF EfmCuPme10PStatusEntry
Beili Expires April 27, 2006 [Page 57]
Internet-Draft EFMCu Interfaces MIB October 2005
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table reflecting status of EFMCu 10PASS-TS PMEs (modems)."
::= { efmCuPme10P 2 }
efmCuPme10PStatusEntry OBJECT-TYPE
SYNTAX EfmCuPme10PStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the EFMCu 10PASS-TS PME Status table."
AUGMENTS { efmCuPmeStatusEntry }
::= { efmCuPme10PStatusTable 1 }
EfmCuPme10PStatusEntry ::=
SEQUENCE {
efmCuPme10PElectricalLength Integer32,
efmCuPme10PFECCorrectedBlocks Counter32,
efmCuPme10PFECUncorrectedBlocks Counter32
-- EdNote: To be continued
}
efmCuPme10PElectricalLength OBJECT-TYPE
SYNTAX Integer32(0..8192|65535)
UNITS "m"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Electrical Length in meters as perceived by the 10PASS-TS PME
after the link is established.
The value of 65535 is returned if the link is Down or
Initializing or the PME is unable to estimate the Electrical
Length.
If a Clause 45 MDIO Interface to the PME is present, then this
object maps to the 10P Electrical Length register"
REFERENCE
"[802.3ah] 45.2.1.21"
::= { efmCuPme10PStatusEntry 1 }
efmCuPme10PFECCorrectedBlocks OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of received and corrected FEC codewords in 10PASS-TS
PME.
Beili Expires April 27, 2006 [Page 58]
Internet-Draft EFMCu Interfaces MIB October 2005
This object maps to aPMEFECCorrectedBlocks attribute in
clause 30.
If a Clause 45 MDIO Interface to the PMA/PMD is present,
then this object maps to the 10P FEC correctable errors
register"
REFERENCE
"[802.3ah] 45.2.1.22"
::= { efmCuPme10PStatusEntry 2 }
efmCuPme10PFECUncorrectedBlocks OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of received FEC codewords in 10PASS-TS PME, which are
uncorrectable.
This object maps to aPMEFECUncorrectableBlocks attribute in
clause 30.
If a Clause 45 MDIO Interface to the PMA/PMD is present,
then this object maps to the 10P FEC uncorrectable errors
register"
REFERENCE
"[802.3ah] 45.2.1.23"
::= { efmCuPme10PStatusEntry 3 }
-- ifAvailableStackTable for use in Discovery
ifAvailableStackTable OBJECT-TYPE
SYNTAX SEQUENCE OF IfAvailableStackEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table, modeled after ifStackTable from [IF-MIB],
contains information on the possible 'on-top-of'
relationships between the multiple sub-layers of network
interfaces (as opposed to actual relationships in
ifStackTable). In particular, it contains information on
which PCS ports (sublayers) can possibly run 'on top of'
which PMEs (sublayers), as determined by cross-connect
capability of the EFMCu device, where each sub-layer
corresponds to a conceptual row in the ifTable. For example,
when the PCS port with ifIndex value x can be connected
to run on top of the PME with ifIndex value y, then this table
contains:
Beili Expires April 27, 2006 [Page 59]
Internet-Draft EFMCu Interfaces MIB October 2005
ifAvailableStackStatus.x.y=capable
Note that there's always at least on PCS for each PME and at
least one PME for each PCS in the EFMCu devices, with
efmCuPAFCapacity and efmCuPeerPAFCapacity indicating
maximum number of PMEs which can be aggregated by local and
remote PCS port respectively.
This table is read only as it describes device capability"
REFERENCE
"ifStackTable of RFC 2863"
::= { efmCuObjects 3 }
ifAvailableStackEntry OBJECT-TYPE
SYNTAX IfAvailableStackEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information on a particular relationship between two
sub-layers, specifying that one sub-layer (PCS) runs on 'top'
of the other sub-layer (PME). Each sub-layer corresponds to a
conceptual row in the ifTable (interface index for PCS and
PME respectively)."
INDEX {
ifAvailableStackHigherLayer,
ifAvailableStackLowerLayer
}
::= { ifAvailableStackTable 1 }
IfAvailableStackEntry ::=
SEQUENCE {
ifAvailableStackHigherLayer InterfaceIndex,
ifAvailableStackLowerLayer InterfaceIndex,
ifAvailableStackStatus INTEGER
}
ifAvailableStackHigherLayer OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of ifIndex corresponding to the higher sub-layer
of the 'cross-connect capability' relationship, i.e., the
PCS sub-layer which MAY run on 'top' of the PME sub-layer
identified by the corresponding instance of
ifAvailableStackLowerLayer."
::= { ifAvailableStackEntry 1 }
Beili Expires April 27, 2006 [Page 60]
Internet-Draft EFMCu Interfaces MIB October 2005
ifAvailableStackLowerLayer OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of ifIndex corresponding to the lower sub-layer
of the 'cross-connect capability' relationship, i.e., the
PME sub-layer which MAY run 'below' the PCS sub-layer
identified by the corresponding instance of
ifAvailableStackHigherLayer."
::= { ifAvailableStackEntry 2 }
ifAvailableStackStatus OBJECT-TYPE
SYNTAX INTEGER {
capable(1),
outOfService(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status of the 'cross-connect capability' relationship
between two sub-layers. The following values are defined:
capable(1) - the PME sub-layer interface, identified by
the ifAvailableStackLowerLayer MAY be
connected to run 'below' the PCS sub-layer
interface, identified by the
ifAvailableStackLowerLayer.
outOfService(2) - the PME sub-layer interface cannot be
connected due to unavailability of the
interface.
Note that PME availability per PCS, indicated by 'capable'
value, can be constrained by other parameters,
for example by aggregation capacity of a PCS or by the PME in
question being already connected to another PCS. So, in
order to ensure that a particular PME can be connected to the
PCS, all respective parameters (e.g. ifAvailableStackTable,
ifStackTable and efmCuPAFCapacity) SHALL be inspected.
This object is read only, unlike ifStackStatus, as it
describes the device capability."
::= { ifAvailableStackEntry 3 }
--
-- Conformance Statements
--
Beili Expires April 27, 2006 [Page 61]
Internet-Draft EFMCu Interfaces MIB October 2005
efmCuGroups OBJECT IDENTIFIER ::= { efmCuConformance 1 }
efmCuCompliances OBJECT IDENTIFIER ::= { efmCuConformance 2 }
-- Object Groups
efmCuBasicGroup OBJECT-GROUP
OBJECTS {
efmCuPAFSupported,
efmCuAdminProfile,
efmCuTargetDataRate,
efmCuTargetSnrMgn,
efmCuPortSide,
efmCuFltStatus
}
STATUS current
DESCRIPTION
"A collection of objects required for all of EFMCu ports."
::= { efmCuGroups 1 }
efmCuPAFGroup OBJECT-GROUP
OBJECTS {
efmCuPeerPAFSupported,
efmCuPAFCapacity,
efmCuPeerPAFCapacity,
efmCuPAFAdminState,
efmCuPAFDiscoveryCode,
efmCuPAFRemoteDiscoveryCode,
efmCuNumPMEs,
ifAvailableStackStatus
}
STATUS current
DESCRIPTION
"A collection of objects required for optional PME
Aggregation Function (PAF) and PAF discovery in EFMCu ports."
::= { efmCuGroups 2 }
ifStackCapabilityGroup OBJECT-GROUP
OBJECTS {
ifAvailableStackStatus
}
STATUS current
DESCRIPTION
"A collection of objects providing information on
the stacking capability of MIB-II interfaces."
::= { efmCuGroups 3 }
efmCuPAFErrorsGroup OBJECT-GROUP
Beili Expires April 27, 2006 [Page 62]
Internet-Draft EFMCu Interfaces MIB October 2005
OBJECTS {
efmCuPAFInErrors,
efmCuPAFInSmallFragments,
efmCuPAFInLargeFragments,
efmCuPAFInBadFragments,
efmCuPAFInLostFragments,
efmCuPAFInLostStarts,
efmCuPAFInLostEnds,
efmCuPAFInOverflows
}
STATUS current
DESCRIPTION
"A collection of objects supporting optional error counters
of PAF on EFMCu ports."
::= { efmCuGroups 4 }
efmCuPmeGroup OBJECT-GROUP
OBJECTS {
efmCuPmeAdminProfile,
efmCuPmeOperStatus,
efmCuPmeFltStatus,
efmCuPmeSubTypesSupported,
efmCuPmeAdminSubType,
efmCuPmeOperSubType,
efmCuPAFRemoteDiscoveryCode,
efmCuPmeOperProfile,
efmCuPmeSnrMgn,
efmCuPmePeerSnrMgn,
efmCuPmeLineAtn,
efmCuPmePeerLineAtn,
efmCuPmeTCCodingErrors,
efmCuPmeTCCrcErrors,
efmCuPmeThreshLineAtn,
efmCuPmeThreshSnrMgn
}
STATUS current
DESCRIPTION
"A collection of objects providing information about
a 2BASE-TL/10PASS-TS PME."
::= { efmCuGroups 5 }
efmCuAlarmConfGroup OBJECT-GROUP
OBJECTS {
efmCuThreshLowBandwidth,
efmCuLowBandwidthEnable,
efmCuPmeThreshLineAtn,
efmCuPmeLineAtnCrossingEnable,
efmCuPmeThreshSnrMgn,
Beili Expires April 27, 2006 [Page 63]
Internet-Draft EFMCu Interfaces MIB October 2005
efmCuPmeSnrMgnCrossingEnable,
efmCuPmeLineAtnCrossingEnable,
efmCuPmeDeviceFaultEnable,
efmCuPmeConfigInitFailEnable,
efmCuPmeProtocolInitFailEnable
-- efmCuPmeThreshES,
-- efmCuPmethreshSES,
-- efmCuPmeThreshCRCanomalies,
-- efmCuPmeThreshLOSWS,
-- efmCuPmeThreshUAS
}
STATUS current
DESCRIPTION
"A collection of objects required for configuration of alarm
thresholds and notifications in EFMCu ports."
::= { efmCuGroups 6 }
efmCuNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
efmCuLowBandwidth,
efmCuPmeLineAtnCrossing,
efmCuPmeSnrMgnCrossing,
efmCuPmeDeviceFault,
efmCuPmeConfigInitFailure,
efmCuPmeProtocolInitFailure
-- efmCuPmePerfES,
-- efmCuPmePerfSES,
-- efmCuPmePerfCRCanomalies,
-- efmCuPmePerfLOSWS,
-- efmCuPmePerfUAS,
-- efmCuPmeDeviceFault,
-- efmCuPmeLocalPowerLoss
}
STATUS current
DESCRIPTION
"This group supports notifications of significant conditions
associated with EFMCu ports."
::= { efmCuGroups 7 }
efmCuPme2BProfileGroup OBJECT-GROUP
OBJECTS {
efmCuPme2BProfileDescr,
efmCuPme2BRegion,
efmCuPme2BDataRate,
efmCuPme2BPower,
efmCuPme2BConstellation,
efmCuPme2BProfileRowStatus
}
Beili Expires April 27, 2006 [Page 64]
Internet-Draft EFMCu Interfaces MIB October 2005
STATUS current
DESCRIPTION
"A collection of objects that constitute a configuration
profile for configuration of 2BASE-TL ports."
::= { efmCuGroups 8 }
efmCuPme10PProfileGroup OBJECT-GROUP
OBJECTS {
efmCuPme10PProfileDescr,
efmCuPme10PBandplanPSDMskProfile,
efmCuPme10PUPBOReferenceProfile,
efmCuPme10PBandNotchProfiles,
efmCuPme10PPayloadURateProfile,
efmCuPme10PPayloadDRateProfile,
efmCuPme10PProfileRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects that constitute a configuration
profile for configuration of 10PASS-TS ports."
::= { efmCuGroups 9 }
efmCuPme10PStatusGroup OBJECT-GROUP
OBJECTS {
efmCuPme10PElectricalLength,
efmCuPme10PFECCorrectedBlocks,
efmCuPme10PFECUncorrectedBlocks
}
STATUS current
DESCRIPTION
"A collection of objects providing status information
specific to 10PASS-TS PMEs."
::= { efmCuGroups 10 }
-- Compliance Statements
efmCuCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for 2BASE-TL/10PASS-TS interfaces.
Compliance with the following external compliance statements
is prerequisite:
MIB Module Compliance Statement
---------- --------------------
IF-MIB ifCompliance3
IF-INVERTED-STACK-MIB ifInvCompliance
EtherLike-MIB dot3Compliance2
Beili Expires April 27, 2006 [Page 65]
Internet-Draft EFMCu Interfaces MIB October 2005
MAU-MIB mauModIfCompl3"
MODULE -- this module
MANDATORY-GROUPS {
efmCuBasicGroup,
efmCuPmeGroup,
efmCuAlarmConfGroup,
efmCuNotificationGroup
}
GROUP efmCuPme2BProfileGroup
DESCRIPTION
"Support for this group is only required for implementations
supporting 2BASE-TL Phy."
GROUP efmCuPme10PProfileGroup
DESCRIPTION
"Support for this group is only required for implementations
supporting 10PASS-TS Phy."
GROUP efmCuPAFGroup
DESCRIPTION
"Support for this group is only required for
implementations supporting PME Aggregation Function (PAF)."
GROUP ifStackCapabilityGroup
DESCRIPTION
"Support for this group is optional for implementations
supporting layered interfaces architecture with
flexible cross-connect between the layers."
GROUP efmCuPAFErrorsGroup
DESCRIPTION
"Support for this group is optional for implementations
supporting PME Aggregation Function (PAF)."
GROUP efmCuPme10PStatusGroup
DESCRIPTION
"Support for this group is optional for implementations
supporting 10PASS-TS Phy."
OBJECT efmCuPmeSubTypesSupported
SYNTAX BITS {
ieee2BaseTLO(0),
ieee2BaseTLR(1),
ieee10PassTSO(2),
ieee10PassTSR(3)
}
Beili Expires April 27, 2006 [Page 66]
Internet-Draft EFMCu Interfaces MIB October 2005
DESCRIPTION
"Support for all subtypes is not required. However at least
one value SHALL be supported"
OBJECT efmCuPmeAdminSubType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required (needed only for PMEs
supporting more than a single subtype, e.g.
ieee2BaseTLO and ieee2BaseTSR or ieee2BaseTLR and
ieee10PassTSR)"
OBJECT efmCuTargetSnrMgn
MIN-ACCESS read-only
DESCRIPTION
"Write access is optional. For PHYs without write access
the target SNR margin SHALL be fixed at 5dB for 2BASE-TL
and 6dB for 10PASS-TS."
-- EdNote: To be Continued
::= { efmCuCompliances 1 }
END
6. Security Considerations
There is a number of managed objects defined in this MIB module that
have a MAX-ACCESS clause of read-write or read-create. Most objects
are writeable only when the link is Down. Writing to these objects
can have potentially disruptive effects on network operation, for
example:
o Changing of efmCuPmeAdminSubType MAY lead to a potential locking
of the link, as peer PMEs of the same sub-type cannot exchange
handshake messages.
o Changing of efmCuPAFAdminState to enabled MAY lead to a potential
locking of the link, if the peer Phy does not support PAF.
o Changing of efmCuPAFDiscoveryCode, before the discovery operation,
MAY lead to a wrongful discovery, for example when two -O ports
are connected to the same multi-PME -R port and both -O ports have
the same Discovery register value.
Beili Expires April 27, 2006 [Page 67]
Internet-Draft EFMCu Interfaces MIB October 2005
o Changing PCS or PME configuration parameters (e.g. profile of a
PCS or PME via efmCuAdminProfile or efmCuPmeAdminProfile) MAY lead
to anything from link quality and rate degradation to a complete
link initialization failure, as ability of an EFMCu port to
support a particular configuration depends on the copper
environment.
o Activation of a PME can cause a severe degradation of service for
another EFMCu Phy, whose PME(s) MAY be affected by the cross-talk
from the newly activated PME.
o Removal of a PME from an operationally 'up' EFMCu port,
aggregating several PMEs, MAY cause port's rate degradation
The user of this MIB module must therefore be aware that support for
SET operations in a non-secure environment without proper protection
can have a negative effect on network operations.
The readable objects in this MIB module (i.e., those with MAX-ACCESS
other than not-accessible) may be considered sensitive in some
environments since, collectively, they provide information about the
performance of network interfaces and can reveal some aspects of
their configuration. In particular since EFMCu can be carried over
Unshielded Twisted Pair (UTP) voice grade copper in a bundle with
other pairs belonging to another operator/customer, it is
theoretically possible to evasdrop to an EFMCu transmission simply by
"listening" to a cross-talk from an EFMCu pair, especially if the
parameters of the EFMCu link in question are known. In such
environments it is important to control even GET and NOTIFY access to
these objects and possibly even to encrypt their values when sending
them over the network via SNMP.
SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPSec),
even then, there is no control as to who on the secure network is
allowed to access and GET/SET (read/change/create/delete) the objects
in this MIB module.
It is RECOMMENDED that implementers consider the security features as
provided by the SNMPv3 framework (see [RFC3410], section 8),
including full support for the SNMPv3 cryptographic mechanisms (for
authentication and privacy).
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module is properly configured to give access to
Beili Expires April 27, 2006 [Page 68]
Internet-Draft EFMCu Interfaces MIB October 2005
the objects only to those principals (users) that have legitimate
rights to indeed GET or SET (change/create/delete) them.
7. IANA Considerations
The two new values of dot3MauType (dot3MauType2BaseTL and
dot3MauType10PassTS) and corresponding IANAifMauTypeListBits bit
definitions (b2BaseTL and b10PassTS) SHALL be defined by the IANA in
the IANA-MAU-TC-MIB module (see [I-D.ietf-hubmib-rfc3636bis]) before
this document is published as an RFC.
8. Acknowledgments
This document was produced by the IETF Ethernet Interfaces and Hub
MIB Working Group, whose efforts were greatly advanced by the
contributions of the following people (in alphabetical order):
Dan Romascanu
Mathias Riess
Matt Squire
Mike Heard
Udi Ashkenazi
9. References
9.1. Normative References
[802.3ah] IEEE, "IEEE Standard for Information technology -
Telecommunications and information exchange between
systems - Local and metropolitan area networks - Specific
requirements - Part 3: Carrier Sense Multiple Access with
Collision Detection (CSMA/CD) Access Method and Physical
Layer Specifications - Amendment: Media Access Control
Parameters, Physical Layers and Management Parameters for
Subscriber Access Networks", IEEE Std 802.3ah-2004,
September 2004.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Beili Expires April 27, 2006 [Page 69]
Internet-Draft EFMCu Interfaces MIB October 2005
McCloghrie, K., Rose, M., and S. Waldbusser, "Structure of
Management Information Version 2 (SMIv2)", STD 58,
RFC 2578, April 1999.
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
McCloghrie, K., Rose, M., and S. Waldbusser, "Textual
Conventions for SMIv2", STD 58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Conformance Statements for SMIv2", STD 58, RFC 2580,
April 1999.
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction and Applicability Statements for Internet-
Standard Management Framework", RFC 3410, December 2002.
9.2. Informative References
[G.991.2] ITU-T, "Single-pair High-speed Digital Subscriber Line
(SHDSL) transceivers", ITU-T Recommendation G.991.2,
December 2003.
[G.993.1] ITU-T, "Very High speed Digital Subscriber Line
transceivers", ITU-T Recommendation G.993.1, June 2004.
[I-D.ietf-adslmib-gshdslbis]
Sikes, C., Ray, B., and R. Abbi, "Definitions of Managed
Objects for G.shdsl.bis Lines",
draft-ietf-adslmib-gshdslbis-11 (work in progress),
May 2005.
[I-D.ietf-hubmib-efm-epon-mib]
Khermosh, L., "Managed Objects for the Ethernet Passive
Optical Networks", draft-ietf-hubmib-efm-epon-mib-03 (work
in progress), March 2005.
[I-D.ietf-hubmib-efm-mib]
Squire, M., "Ethernet in the First Mile (EFM) Common MIB",
draft-ietf-hubmib-efm-mib-03 (work in progress),
March 2005.
[I-D.ietf-hubmib-rfc3636bis]
Beili, E., "Definitions of Managed Objects for IEEE 802.3
Medium Attachment Units (MAUs)",
draft-ietf-hubmib-rfc3636bis-02 (work in progress),
October 2005.
[IANAifType-MIB]
Beili Expires April 27, 2006 [Page 70]
Internet-Draft EFMCu Interfaces MIB October 2005
Internet Assigned Numbers Authority (IANA), "IANAifType
Textual Convention definition",
http://www.iana.org/assignments/ianaiftype-mib.
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group
MIB", RFC 2863, June 2000.
[RFC2864] McCloghrie, K. and G. Hanson, "The Inverted Stack Table
Extension to the Interfaces Group MIB", RFC 2864,
June 2000.
[RFC3635] Flick, J., "Definitions of Managed Objects for the
Ethernet-like Interface Types", RFC 3635, September 2003.
[RFC4070] Dodge, M. and B. Ray, "Definitions of Managed Object
Extensions for Very High Speed Digital Subscriber Lines
(VDSL) Using Multiple Carrier Modulation (MCM) Line
Coding", RFC 4070, May 2005.
Beili Expires April 27, 2006 [Page 71]
Internet-Draft EFMCu Interfaces MIB October 2005
Author's Address
Edward Beili
Actelis Networks
Bazel 25
Petach-Tikva
Israel
Phone: +972-3-924-3491
Email: edward.beili@actelis.com
Beili Expires April 27, 2006 [Page 72]
Internet-Draft EFMCu Interfaces MIB October 2005
Intellectual Property Statement
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Disclaimer of Validity
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Copyright Statement
Copyright (C) The Internet Society (2005). This document is subject
to the rights, licenses and restrictions contained in BCP 78, and
except as set forth therein, the authors retain all their rights.
Acknowledgment
Funding for the RFC Editor function is currently provided by the
Internet Society.
Beili Expires April 27, 2006 [Page 73]
| PAFTECH AB 2003-2026 | 2026-04-23 23:48:54 |