One document matched: draft-ietf-dhc-isnsoption-10.txt
Differences from draft-ietf-dhc-isnsoption-09.txt
DHC Working Group Charles Monia
INTERNET DRAFT Josh Tseng
Expires: March 2004 Kevin Gibbons
Internet Draft
Document: <draft-ietf-dhc-isnsoption-10.txt> Nishan Systems
Category: Standards Track September 2003
The IPv4 DHCP Option for the Internet Storage Name Service
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of [RFC2026].
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts. Internet-Drafts are draft documents valid for a maximum of
six months and may be updated, replaced, or made obsolete by other
documents at any time. It is inappropriate to use Internet- Drafts
as reference material or to cite them other than as "work in
progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Comments
Comments should be sent to the DHCP mailing list (dhcwg@ietf.org) or
to the authors.
Table of Contents
Monia, et-al Standards Track [Page 1]
DHCP Option Number for iSNS Revision 10 September 2003
Status of this Memo...................................................1
Comments..............................................................1
Abstract..............................................................3
Conventions used in this document.....................................3
1. Introduction.....................................................3
2. iSNS Option for DHCP.............................................4
2.1 iSNS Functions Field.............................................5
2.2 Discovery Domain Access Field....................................7
2.3 Administrative Flags Field.......................................8
2.4 iSNS Server Security Bitmap......................................9
3. Security Considerations.........................................10
4. IANA Considerations.............................................11
5. Normative References............................................11
6. Non-Normative References........................................11
7. Author's Addresses..............................................12
Full Copyright Statement.............................................13
Monia, et-al Standards Track [Page 2]
DHCP Option Number for iSNS Revision 10 September 2003
Abstract
This document describes the DHCP option to allow Internet Storage
Name Service (iSNS) clients to automatically discover the location
of the iSNS server through the use of DHCP for IPv4. iSNS provides
discovery and management capabilities for Internet SCSI (iSCSI) and
Internet Fibre Channel Protocol (iFCP) storage devices in an
enterprise-scale IP storage network. iSNS provides intelligent
storage management services comparable to those found in Fibre
Channel networks, allowing a commodity IP network to function in a
similar capacity as a storage area network.
Conventions used in this document
iSNS refers to the Internet Storage Name Service framework
consisting of the storage network model and associated services.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in
this document are to be interpreted as described in [RFC2119].
All frame formats are in big endian network byte order. RESERVED
fields SHOULD be set to zero.
This document uses the following terms:
"iSNS Client" - iSNS clients are processes resident in iSCSI and
iFCP devices that initiate transactions with the iSNS server using
the iSNS Protocol.
"iSNS Server" - The iSNS server responds to iSNS protocol query and
registration messages, and initiates asynchronous notification
messages. The iSNS server stores information registered by iSNS
clients.
"iSCSI (Internet SCSI)" - iSCSI is an encapsulation of SCSI for a
new generation of storage devices interconnected with TCP/IP.
"iFCP (Internet Fibre Channel Protocol)" - iFCP is a gateway-to-
gateway protocol designed to interconnect existing Fibre Channel
devices using TCP/IP. iFCP maps the Fibre Channel transport and
fabric services to TCP/IP.
1. Introduction
The Dynamic Host Configuration Protocol for IPv4 provides a
framework for passing configuration information to hosts. Its
usefulness extends to hosts and devices using the iSCSI and iFCP
protocols to connect to block level storage assets over a TCP/IP
network.
The iSNS Protocol provides a framework for automated discovery,
management, and configuration of iSCSI and iFCP devices on a TCP/IP
network. It provides functionality similar to that found on Fibre
Monia, et-al Standards Track [Page 3]
DHCP Option Number for iSNS Revision 10 September 2003
Channel networks, except that iSNS works within the context of an IP
network. iSNS thereby provides the requisite storage intelligence
to IP networks that are standard on existing Fibre Channel networks.
Existing DHCP options cannot be used to find iSNS servers for the
following reasons:
a) iSNS functionality is distinctly different from other protocols
using DHCP options. Specifically, iSNS provides a significant
superset of capabilities compared to typical name resolution
protocols such as DNS. It is designed to support client devices
that allow themselves to be configured and managed from a
central iSNS server
b) iSNS requires a DHCP option format that provides more than the
location of the iSNS server. The DHCP option needs to specify
the subset of iSNS services that may be actively used by the
iSNS client.
The DHCP option number for iSNS is used by iSCSI and iFCP devices to
discover the location and role of the iSNS server. The DHCP option
number assigned for iSNS by IANA is <<TBD>>.
2. iSNS Option for DHCP
This option specifies the location of the primary and backup iSNS
servers and the iSNS services available to an iSNS client.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Code = TBD | Length | iSNS Functions |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| DD Access | Administrative FLAGS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| iSNS Server Security Bitmap |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| a1 | a2 | a3 | a4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| b1 | b2 | b3 | b4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| . . . . |
| Additional Secondary iSNS Servers |
| . . . . |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 1 -- iSNS Server Option
The iSNS Option specifies a list of IP addresses used by iSNS
servers. The option contains the following parameters:
Length: the number of bytes that follow the Length field.
Monia, et-al Standards Track [Page 4]
DHCP Option Number for iSNS Revision 10 September 2003
iSNS Functions: A bitmapped field defining the functions supported
by the iSNS servers. The format of this field is described
in section 2.1.
Discovery Domain Access: A bit field indicating the types of iSNS
clients that are allowed to modify Discovery Domains. The
field contents are described in section 2.2.
Administrative Flags field: Contains the administrative settings for
the iSNS servers discovered through the DHCP query. The
contents of this field are described in section 2.3.
iSNS Server Security Bitmap: Contains the iSNS server security
settings specified in section 2.4.
a1...a4: Depending on the setting of the Heartbeat bit in the
Administrative Flags field (see section 2.3), this field
contains either the IP address from which the iSNS heartbeat
originates (see [ISNS]) or the IP address of the primary
iSNS server.
b1...b4: Depending on the setting of Heartbeat bit in the
Administrative Flags field (see section 2.3), this field
contains either the IP address of the primary iSNS server or
a secondary iSNS server.
Additional Secondary iSNS Servers: Each set of four octets specifies
the IP address of a secondary iSNS server.
The Code field through IP address field a1...a4 MUST be present in
every response to the iSNS query, hence the Length field has a
minimum value of 14.
If the Heartbeat bit is set in the Administrative Flags field (see
section 2.3), then b1...b4 MUST also be present. In this case, the
minimum value of the Length field is 18.
The inclusion of Additional Secondary iSNS Servers in the response
MUST be indicated by increasing the Length field accordingly.
2.1 iSNS Functions Field
The iSNS Functions Field defines the iSNS server's operational role
(i.e., how the iSNS server is to be used). The iSNS server's role
can be as basic as providing simple discovery information, or as
significant as providing IKE/IPSec security policies and
certificates for the use of iSCSI and iFCP devices. The format of
the iSNS Functions field is shown in Figure 2:
Monia, et-al Standards Track [Page 5]
DHCP Option Number for iSNS Revision 10 September 2003
0 1 1
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved |S|A|E|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2 -- iSNS Functions Field
Bit field Significance
--------- ------------
15 Function Fields Enabled
14 DD-Based Authorization
13 Security Policy Distribution
iSNS Functions Field definitions:
Function Fields This bit specifies the validity of the
Enabled: remaining iSNS Function fields. If set to
one, then the contents of all other iSNS
Function fields are valid. If set to zero,
then the contents of all other iSNS
Function fields MUST be ignored.
DD-based Indicates whether or not devices in a
Authorization: common Discovery Domain (DD) are implicitly
authorized to access one another. Although
Discovery Domains control the scope of
device discovery, they do not necessarily
indicate whether or not a domain member is
authorized to access discovered devices.
If this bit is set to one, then devices in
a common Discovery Domain are automatically
allowed access to each other (if
successfully authenticated). If this bit
is set to zero, then access authorization
is not implied by domain membership and
must be explicitly performed by each
device. In either case, devices not in a
common discovery domain are not allowed to
access each other.
Security Policy Indicates whether the iSNS client is to
Distribution: download and use the security policy
configuration stored in the iSNS server.
If set to one, then the policy is stored in
the iSNS server and must be used by the
iSNS client for its own security policy.
If set to zero, then the iSNS client must
obtain its security policy configuration by
other means.
Monia, et-al Standards Track [Page 6]
DHCP Option Number for iSNS Revision 10 September 2003
2.2 Discovery Domain Access Field
The format of the DD Access bit field is shown in Figure 3:
0 1
0 1 2 3 4 5 6 ... 5
+---+---+---+---+---+---+---+---+---+
| if| tf| is| ts| C | E | Reserved |
+---+---+---+---+---+---+---+---+---+
Figure 3 -- Discovery Domain Access Field
Bit field Significance
--------- ------------
5 Enabled
4 Control Node
3 iSCSI Target
2 iSCSI Initiator
1 iFCP Target Port
0 iFCP Initiator Port
Discovery Domain Access Field Definitions:
Enabled: This bit specifies the validity of the
remaining DD Access bit fields. If this
bit is set to one, then the contents of
the remainder of the DD Access field are
valid. If this bit is set to zero, then
the contents of the remainder of this
field MUST be ignored.
Control Node: Specifies whether the iSNS server allows
Discovery Domains to be added, modified
or deleted by means of Control Nodes. If
set to one, then Control Nodes are
allowed to modify the Discovery Domain
configuration. If set to zero, then
Control Nodes are not allowed to modify
Discovery Domain configurations.
iSCSI Target, These bits determine whether the
iSCSI Initiator, respective registered iSNS client
iFCP Target Port, (determined by iSCSI Node Type or iFCP
iFCP Initiator Port Role) is allowed to add, delete, or
Port: modify Discovery Domains. If set to
one, then modification by the specified
client type is allowed. If set to zero,
then modification by the specified
client type is not allowed.
(A node may implement multiple node
types.)
Monia, et-al Standards Track [Page 7]
DHCP Option Number for iSNS Revision 10 September 2003
2.3 Administrative Flags Field
The format of the Administrative Flags bit field is shown in
Figure 4:
0 1 1
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| RESERVED |D|M|H|E|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 4 -- Administrative Flags
Bit Field Significance
--------- ------------
15 Enabled
14 Heartbeat
13 Management SCNs
12 Default Discovery Domain
Administrative Flags Field definitions:
Enabled: Specifies the validity of the remainder
of the Administrative Flags field. If
set to one, then the contents of the
remaining Administrative Flags are
valid. If set to zero, then the
remaining contents MUST be ignored,
indicating that iSNS administrative
settings are obtained through means
other than DHCP.
Heartbeat: Indicates whether the first IP address
is the multicast address to which the
iSNS heartbeat message is sent. If set
to one, then a1-a4 contains the
heartbeat multicast address and b1-b4
contains the IP address of the primary
iSNS server, followed by the IP
address(es) of any backup servers (see
Figure 1). If set to zero, then a1-a4
contains the IP address of the primary
iSNS server, followed by the IP
address(es) of any backup servers.
Management SCNs: Indicates whether control nodes are
authorized to register to receive
Management State Change Notifications
(SCN's). Management SCN's are a special
class of State Change Notification whose
scope is the entire iSNS database. If
set to one, then control nodes are
authorized to register to receive
Management SCN's. If set to zero, then
Monia, et-al Standards Track [Page 8]
DHCP Option Number for iSNS Revision 10 September 2003
control nodes are not authorized to
receive Management SCN's (although they
may receive normal SCN's).
Default Discovery Indicates whether a newly registered
Domain: device that is not explicitly placed
into a Discovery Domain (DD) and
Discovery Domain Set (DDS) should be
automatically placed into a default DD
and DDS. If set to one, then a default
DD shall contain all devices in the iSNS
database that have not been explicitly
placed into a DD by an iSNS client. If
set to zero, then devices not explicitly
placed into a DD are not members of any
DD.
2.4 iSNS Server Security Bitmap
The format of the iSNS server security Bitmap field is shown in
Figure 5. If valid, this field communicates to the DHCP client the
security settings that are required to communicate with the
indicated iSNS server.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved |T|X|P|A|M|S|E|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 5 -- iSNS Server Security Bitmap
Bit Field Significance
--------- ----------------
31 Enabled
30 IKE/IPSec
29 Main Mode
28 Aggressive Mode
27 PFS
26 Transport Mode
25 Tunnel Mode
iSNS Server Security Bitmap definitions:
Monia, et-al Standards Track [Page 9]
DHCP Option Number for iSNS Revision 10 September 2003
Enabled This bit specifies the validity of the
remainder of the iSNS server security
bitmap. If set to one, then the contents
of the remainder of the field are valid.
If set to zero, then the contents of the
rest of the field are undefined and MUST
be ignored.
IKE/IPSec 1 = IKE/IPSec enabled; 0 = IKE/IPSec
disabled.
Main Mode 1 = Main Mode enabled; 0 = Main Mode
disabled.
Aggressive Mode 1 = Aggressive mode enabled; 0 =
Aggressive mode disabled.
PFS 1 = PFS enabled; 0 = PFS disabled.
Transport Mode 1 = Transport mode preferred; 0 = No
preference.
Tunnel Mode 1 = Tunnel mode preferred; 0 = No
preference.
If IKE/IPSec is disabled, this indicates that the Internet Key
Exchange (IKE) Protocol is not available to configure IPSec keys for
iSNS sessions to this iSNS server. It does not necessarily preclude
other key exchange methods (e.g., manual keying) from establishing
an IPSec security association for the iSNS session.
If IKE/IPsec is enabled, an implementation SHALL enable:
a) One of Main Mode or Aggressive Mode but not both and
b) One of Transport Mode or Tunnel Mode but not both.
3. Security Considerations
DHCP security considerations are addressed in [RFC3118]. Among
these is the potential for a "man-in-the-middle" attack by a hostile
entity modifying or replacing the original iSNS option message.
Unless some form of authentication is implemented, an attacker may
trick the iSNS client into connecting into rogue iSNS servers.
To thwart such attacks, the DHCP response should be verified in some
manner. One approach is direct authentication via [RFC3118], when
implemented. Since this technology is not widely deployed, an
alternative is to authenticate the discovered iSNS server through
use of IPSec or the iSNS authentication block as described in
[ISNS]. Of course, use of iSNS Server authentication implies a site
Monia, et-al Standards Track [Page 10]
DHCP Option Number for iSNS Revision 10 September 2003
wide policy requiring use of one of the authentication methods
specified in [ISNS] by all iSNS servers.
If no authentication is used and it is determined that the potential
exists for one of the attacks described in [RFC3118], then the DHCP
option message for iSNS should not be utilized.
4. IANA Considerations
In accordance with the policy defined in [DHCP], IANA has assigned a
value of TBD for this option.
There are no other IANA-assigned values defined by this
specification.
5. Normative References
[DHCP] Droms, R., "Dynamic Host Configuration Protocol", RFC
2131, Bucknell University, March 1997.
[iSNS] Tseng, J. et al., "iSNS - Internet Storage Name
Service", Internet draft (work in progress), draft-ietf-
ips-isns-12.txt, August 2002
[RFC2026] Bradner, S., "The Internet Standards Process --
Revision 3", BCP 9, RFC 2026, October 1996
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997
[RFC3118] Arbaugh, W., Droms, R., "Authentication for DHCP
Messages", RFC 3118, June 2001
6. Non-Normative References
[iFCP] Monia, C., et al., "iFCP - A Protocol for Internet Fibre
Channel Storage Networking", Internet draft (work in
progress), draft-ietf-ips-ifcp-13.txt, May 2002
[iSCSI] Satran, J., et al., "iSCSI", Internet draft (work in
progress), draft-ietf-ips-iSCSI-15.txt, August 2002
[SEC-IPS] Aboba, B., et al., "Securing IP Block Storage
Protocols", draft-ietf-ips-security-14.txt, June 2002
Monia, et-al Standards Track [Page 11]
Internet Storage Name Service (iSNS) November 2001
7. Author's Addresses
Kevin Gibbons,
Charles Monia,
Josh Tseng
Nishan Systems
3850 North First Street
San Jose, CA 95134-1702
Phone: (408) 519-3700
Email: cmonia@nishansystems.com
jtseng@nishansystems.com
kgibbons@nishansystems.com
Monia, et-al Standards Track [Page 12]
Full Copyright Statement
"Copyright (C) The Internet Society September 2003. All Rights
Reserved. This document and translations of it may be copied and
furnished to others, and derivative works that comment on or
otherwise explain it or assist in its implementation may be
prepared, copied, published and distributed, in whole or in part,
without restriction of any kind, provided that the above copyright
notice and this paragraph are included on all such copies and
derivative works. However, this document itself may not be modified
in any way, such as by removing the copyright notice or references
to the Internet Society or other Internet organizations, except as
needed for the purpose of developing Internet standards in which
case the procedures for copyrights defined in the Internet Standards
process must be followed, or as required to translate it into
languages other than English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE."
Monia, et-al Standards Track [Page 13]
Monia, et-al Standards Track [Page 14]
| PAFTECH AB 2003-2026 | 2026-04-20 05:58:51 |