One document matched: draft-ietf-dccp-quickstart-05.txt
Differences from draft-ietf-dccp-quickstart-04.txt
DCCP Working Group G. Fairhurst
Internet-Draft A. Sathiaseelan
Intended status: Experimental University of Aberdeen
Expires: November 31, 2009
Intended status: Experimental 03 June, 2009
Quick-Start for Datagram Congestion Control Protocol (DCCP)
draft-ietf-dccp-quickstart-05.txt
Status of this Draft
This Internet-Draft is submitted to IETF in full conformance with
the provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other documents
at any time. It is inappropriate to use Internet-Drafts as
reference material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on November 31, 2009.
Abstract
This document specifies the use of the Quick-Start mechanism by the
Datagram Congestion Control Protocol (DCCP). DCCP is a transport
protocol that allows the transmission of congestion-controlled,
unreliable datagrams. DCCP is intended for applications such as
streaming media, Internet telephony, and on-line games. In DCCP, an
application has a choice of congestion control mechanisms, each
specified by a Congestion Control Identifier (CCID). This document
specifies general procedures applicable to all DCCP CCIDs and
specific procedures for the use of Quick-Start with DCCP CCID 2,
CCID 3 and CCID 4. Quick-Start enables a DCCP sender to cooperate
with Quick-Start routers along the end-to-end path to determine an
allowed sending rate at the start of a connection and, at times, in
the middle of a DCCP connection (e.g., after an idle or application-
limited period). The present specification is provided for use in
controlled environments, and not as a mechanism that would be
intended or appropriate for ubiquitous deployment in the global
Internet.
Expires September 2009 [page 1]
INTERNET DRAFT Quick-Start for DCCP June 2009
Table of Contents
1. Introduction
1.1 Terminology
2. Quick-Start for DCCP
2.1 Sending a Quick-Start Request for a DCCP flow
2.1.1 The Quick-Start Interval
2.2 Receiving a Quick-Start Request for a DCCP flow
2.2.1 The Quick-Start Response Option
2.3 Receiving a Quick-Start Response
2.3.1 The Quick-Start Mode
2.3.2 The Quick-Start Validation Phase
2.4 Procedure when no response to a Quick-Start Request
2.5 Procedure when a Quick-Start Packet is dropped
2.6 Interactions with Mobility and Signalled Path Changes
2.7 Interactions with Path MTU Discovery
2.8 Interactions with Middle boxes
3. Mechanisms for Specific CCIDs
3.1 Quick-Start for CCID 2
3.1.1 The Quick-Start Request for CCID 2
3.1.2 Sending a Quick-Start Response with CCID 2
3.1.3 Using the Quick-Start Response with CCID 2
3.1.4 Quick-Start Validation Phase for CCID 2
3.1.5 Reported loss or congestion while using Quick-Start
3.1.6 CCID 2 Feedback Traffic on the Reverse Path
3.2 Quick-Start for CCID 3
3.2.1 The Quick-Start Request for CCID 3
3.2.2 Sending a Quick-Start Response with CCID 3
3.2.3 Using the Quick-Start Response with CCID 3
3.2.4 Quick-Start Validation Phase for CCID 3
3.2.5 Reported loss during Quick-Start Mode or Validation Phase
3.2.6 CCID 3 Feedback Traffic on the Reverse Path
3.3 Quick-Start for CCID 4
3.3.1 The Quick-Start Request for CCID 4
3.3.2 Sending a Quick-Start Response with CCID 4
3.3.3 Using the Quick-Start Response with CCID 4
3.3.4 Reported loss or congestion while using Quick-Start
3.3.5 CCID 4 Feedback Traffic on the Reverse Path
4. Discussion of Issues
4.1 Over-run and the Quick-Start Validation Phase
4.2 Experimental Status
5. IANA Considerations
6. Acknowledgments
7. Security Considerations
8. References
8.1 Normative References
8.2 Informative References
9. Authors' Addresses
10. IPR Notices
10.1 Intellectual Property Statement
10.2 Disclaimer of Validity
11. Copyright Statement
Expires November 2009 [Page 2]
INTERNET DRAFT Quick-Start for DCCP June 2009
1. Introduction
The Datagram Congestion Control Protocol (DCCP) [RFC4340] is a
transport protocol for congestion-controlled, unreliable datagrams,
intended for applications such as streaming media, Internet
telephony, and on-line games.
In DCCP, an application has a choice of congestion control
mechanisms, each specified by a Congestion Control Identifier (CCID)
[RFC4340]. There are general procedures applicable to all DCCP CCIDs
that are described in Section 2, and details that relate to how
individual CCIDs should operate, which are described in Section 3.
This separation of CCID-specific and DCCP general functions is in
the spirit of the modular approach adopted by DCCP.
Quick-Start [RFC4782] is an Experimental mechanism for transport
protocols specified for use in controlled environments. The current
specification of this mechanism is not intended or appropriate for
ubiquitous deployment in the global Internet.
Quick-Start is designed for use between end hosts within the same
network or on Internet paths that include IP routers. It works in
cooperation with routers, allowing a sender to determine an allowed
sending rate at the start and at times in the middle of a data
transfer (e.g., after an idle or application-limited period).
This document assumes the reader is familiar with RFC4782 [RFC4782],
which specifies the use of Quick-Start with IP and with TCP. Section
7 of RFC4782 also provides guidelines for the use of Quick-Start
with other transport protocols, including DCCP. This document
provides answers to some of the issues that were raised by RFC4782
and provides a definition of how Quick-Start must be used with DCCP.
In using Quick-Start, the sending DCCP end host indicates the
desired sending rate in bytes per second, using a Quick-Start option
in the IP header of a DCCP packet. Each Quick-Start capable router
along the path could, in turn, either approve the requested rate,
reduce the requested rate, or indicate that the Quick-Start Request
is not approved.
If the Quick-Start Request is approved (possibly with a reduced
rate) by all the routers along the path, then the DCCP receiver
returns an appropriate Quick-Start Response. On receipt of this, the
sending end host can send at up to the approved rate for a period
determined by the method specified for each DCCP CCID, and not
exceeding three round-trip times. Subsequent transmissions will be
governed by the default CCID congestion control mechanisms for the
connection. If the Quick-Start Request is not approved, then the
sender must use the default congestion control mechanisms.
DCCP receivers are not required to acknowledge individual packets
(or pairs of segments) as in TCP. CCID 2 [RFC4341] allows much less
frequent feedback. Rate-based protocols (e.g. TFRC [RFC5348], CCID 3
Expires November 2009 [Page 3]
INTERNET DRAFT Quick-Start for DCCP June 2009
[RFC4342]) have a different feedback mechanism than that of TCP.
With rate-based protocols, feedback may be sent less frequently
(e.g. once per RTT). In such cases, a sender using Quick-Start needs
to implement a different mechanism to determine whether the Quick-
Start sending rate has been sustained by the network. This
introduces a new mechanism called the Quick-Start Validation Phase
(Section 2.5).
In addition, this document defines two more general enhancements
that refine the use of Quick-Start after a flow has started
(expected to be more common in applications using DCCP). These are
the Quick-Start Interval (Section 2.2), and the reaction to mobility
triggers (Section 2.7).
1.1 Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
Expires November 2009 [Page 4]
INTERNET DRAFT Quick-Start for DCCP June 2009
2. Quick-Start for DCCP
Unless otherwise specified, DCCP end hosts follow the procedures
specified in Section 4 of [RFC4782], following the use specified for
Quick-Start with TCP.
2.1 Sending a Quick-Start Request for a DCCP flow
A DCCP sender MAY use a Quick-Start Request during the start of a
connection, when the sender would prefer to have a larger initial
rate than allowed by standard mechanisms (e.g. [RFC5348] or
[RFC3390]).
A Quick-Start Request MAY also be used once a DCCP flow is connected
(i.e., in the middle of a DCCP flow). In standard operation, DCCP
CCIDs can constrain the sending rate (or window) to less than that
desired (e.g. when an application increases the rate at which it
wishes to send). A DCCP sender that has data to send after an idle
period or application-limited period (i.e. where the sender has
transmitted at less than the allowed sending rate) can send a Quick-
Start Request using the procedures defined in Section 3.
Quick-Start Requests will be more effective if the Quick-Start Rate
is not larger than necessary. Each requested Quick-Start Rate that
has been approved, but was not fully utilized, takes away from the
bandwidth pool maintained by Quick-Start routers that would be
otherwise available for granting successive requests [RFC4782].
In contrast to most TCP applications, many DCCP applications have
the notion of a natural media rate that they wish to achieve. For
example, during the initial connection, a host may request a Quick-
Start Rate equal to the media rate of the application, appropriately
increased to account for the size of packet headers. (Note that
Quick-Start only provides a course-grain indication of the
desired rate that is expected to be sent in the next RTT.)
When sending a Quick-Start Request, the DCCP sender SHOULD send the
Quick-Start Request using a packet that requires an acknowledgement,
such as a DCCP-Request, DCCP-Response, or DCCP-Data.
2.1.1 The Quick-Start Interval
Excessive use of the Quick-Start mechanism is undesirable. This
document defines an enhancement to RFC4782 to update the use of
Quick-Start after a DCCP flow has started, by introducing the
concept of the Quick-Start Interval. The Quick-Start Interval
specifies a period of time during which a Quick-Start Request SHOULD
NOT be sent. The Quick-Start Interval is measured from the time of
transmission of the previous Quick-Start Request (section 2.1). The
Quick-Start Interval MAY be overridden as a result of a network path
change (section 2.6).
Expires November 2009 [Page 5]
INTERNET DRAFT Quick-Start for DCCP June 2009
When a connection is established, the Quick-Start Interval is
initialized to the Initial_QSI. The Initial_QSI MUST be at least 6
Seconds (larger values are permitted). This value was chosen so that
it is sufficiently large to prevent excessive router processing over
typical Internet paths. Quick-Start routers that track per-flow
state MAY penalise senders by suspending Quick-Start processing of
flows that make Quick-Start Requests for the same flow with an
interval less than 6 seconds.
When the first Quick-Start Request is sent, the Quick-Start Interval
is set to:
Quick-Start Interval = Initial_QSI;
After sending each subsequent Quick-Start Request, the Quick-Start
Interval is then recalculated as:
Quick-Start Interval = max(Quick-Start Interval *2, 4*RTT);
Each unsuccessful Quick-Start Request therefore results in the
Quick-Start Interval being doubled (resulting in an exponential
back-off). The maximum time the sender can back-off is 64 seconds.
When the back-off calculation results in a larger value, the sender
MUST NOT send any further Quick-Start Requests for the remainder of
the DCCP connection (i.e. the sender ceases to use Quick-Start).
Whenever a Quick-Start Request is approved (at any rate), the Quick-
Start Interval is reset to the Initial_QSI.
2.2 Receiving a Quick-Start Request for a DCCP flow
The procedure for processing a received Quick-Start Request is
normatively defined in [RFC4782] and summarised in this paragraph.
An end host that receives an IP packet containing a Quick-Start
Request passes the Quick-Start Request, along with the value in the
IP TTL field, to the receiving DCCP layer. If the receiving host is
willing to permit the Quick-Start Request, it SHOULD respond
immediately by sending a packet that carries the Quick-Start
Response option in the DCCP header of the corresponding feedback
packet (e.g. using a DCCP-Ack packet or in a DCCP-DataAck packet).
The Rate Request field in the Quick-Start Response option is set to
the received value of the Rate Request in the Quick-Start option or
to a lower value if the DCCP receiver is only willing to allow a
lower Rate Request. Where information is available (e.g. knowledge
of the local layer 2 interface speed), a Quick-Start receiver SHOULD
verify that the received rate does not exceed its expected receive
link capacity. The TTL Diff field in the Quick-Start Response is set
to the difference between the received IP TTL value (Hop Limit field
in IPv6) and the Quick-Start TTL value. The Quick-Start Nonce in
Expires November 2009 [Page 6]
INTERNET DRAFT Quick-Start for DCCP June 2009
the Response is set to the received value of the Quick-Start Nonce
in the Quick-Start option (or IPv6 Header Extension).
The Quick-Start Response MUST NOT be resent if it is lost in the
network [RFC4782]. Packet loss could be an indication of congestion
on the return path, in which case it is better not to approve the
Quick-Start Request.
If an end host receives an IP packet with a Quick-Start Request with
a requested rate of zero, then this host SHOULD NOT send a Quick-
Start Response [RFC4782].
2.2.1 The Quick-Start Response Option
The Quick-Start Response message must be carried by the transport
protocol using Quick-Start. This section defines a DCCP Header
option used to carry the Quick-Start Response. This header option is
REQUIRED for end hosts to utilise the Quick-Start mechanism with
DCCP flows. The format resembles that defined for TCP [RFC4782].
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type=xQSOx | Length=8 | Resv. | Rate | TTL Diff |
| | | |Request| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Quick-Start Nonce | R |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 1. The Quick-Start Response option.
### IANA ACTION, PLEASE REPLACE xQSOx with the assigned value in the
figure above.###
### IANA ACTION, PLEASE ALSO REPLACE xQSOx with the assigned value
in the paragraph below.###
The first byte of the Quick-Start Response option contains the
option kind, identifying the DCCP option (xQSOx).
The second byte of the Quick-Start Response option contains the
option length in bytes. The length field MUST be set to 8 bytes.
The third byte of the Quick-Start Response option contains a four-
bit Reserved field, and the four-bit allowed Rate Request, formatted
as in the IP Quick-Start Rate Request option [RFC4782].
The fourth byte of the DCCP Quick-Start Response option contains the
TTL Diff. The TTL Diff contains the difference between the IP TTL
and Quick-Start TTL fields in the received Quick-Start Request
packet, as calculated in [RFC4782].
Expires November 2009 [Page 7]
INTERNET DRAFT Quick-Start for DCCP June 2009
Bytes 5-8 of the DCCP option contain the 30-bit Quick-Start Nonce
and a two-bit Reserved field [RFC4782].
2.3 Receiving a Quick-Start Response
On reception of a Quick-Start Response packet, the sender MUST
report the approved rate, by sending a Quick-Start Report of
Approved Rate [RFC4782]. This report includes the Rate Report field
set to the Approved Rate, and the QS Nonce set to the QS Nonce value
sent in the Quick-Start Request.
The Quick-Start Report of Approved Rate is sent as an IPv4 option or
IPv6 header extension using the first Quick-Start Packet or sent as
an option using a DCCP control packet if there are no DCCP-Data
packets pending transmission.
The Quick-Start Interval is also reset (as described in section
2.1.1).
Reception of a Quick-Start Response packet that approves a rate
higher than the current rate results in the sender entering the
Quick-Start Mode.
2.3.1 The Quick-Start Mode
While a sender is in the Quick-Start Mode, all sent packets are
known as Quick-Start Packets [RFC4782]. The Quick-Start Packets MUST
be sent at a rate not greater than the rate specified in the Quick-
Start Response. The Quick-Start Mode continues for a period up to
one RTT (shorter, if a feedback message arrives acknowledging the
receipt of one or more Quick-Start Packets).
The procedure following exit of the Quick-Start Mode is specified in
the following paragraphs. Note that this behaviour is CCID-specific
and the details for each current CCID are described in Section 3.
2.3.2 The Quick-Start Validation Phase
After transmitting a set of Quick-Start Packets in the Quick-Start
Mode (and providing that no loss or congestion is reported), the
sender enters the Quick-Start Validation Phase. This phase persists
for a period during which the sender seeks to affirm that the
capacity used by the Quick-Start Packets did not introduce
congestion. This phase is introduced, because unlike TCP, DCCP
senders do not necessarily receive frequent feedback that would
indicate the congestion state of the forward path.
While in the Quick-Start Validation Phase, the sender is tentatively
permitted to continue sending using the Quick-Start rate. This phase
normally concludes when the sender receives feedback that includes
an acknowledgment that all Quick-Start Packets were received.
Expires November 2009 [Page 8]
INTERNET DRAFT Quick-Start for DCCP June 2009
However, the duration of the Quick-Start Validation Phase MUST NOT
exceed the Quick-Start Validation Time (a maximum of 2 RTTs).
Implementations may set a timer (initialised to the Quick-Start
Validation Time) to detect the end of this phase. There may be scope
for optimisation of timer resources in an implementation, since the
Quick-Start Validation period temporarily enforces more strict
monitoring of acknowledgements than normally used in a CCID (e.g. an
implementation may consider using a common timer resource for Quick-
Start Validation and a nofeedback timer)._
An example sequence of packet exchanges showing Quick-Start with
DCCP is shown in Figure 2.
DCCP Sender DCCP Receiver
Quick-Start +----------------------------------------------+
Request/Response | Quick-Start Request --> |
| <-- Quick-Start Response |
| Quick-Start Approve --> |
+----------------------------------------------+
+----------------------------------------------+
Quick-Start | Quick-Start Packets --> |
Mode | Quick-Start Packets --> |
| <-- Feedback A from Receiver|
| (acknowledging first QS Packet)|
+----------------------------------------------+
+----------------------------------------------
Quick-Start | Packets --> |
Validation Phase | <-- Feedback B from Receiver|
| (acknowledging all QS Packets)|
+----------------------------------------------
+----------------------------------------------+
DCCP | Packets --> |
Congestion | <-- Feedback C from Receiver|
Control | |
Figure 2. The Quick-Start Mode and Validation Phase.
On conclusion of the Validation Phase (Feedback B in the above
figure), the sender expects to receive assurance that it may safely
use the current rate. A sender that completes the Quick-Start
Validation Phase with no reported packet loss or congestion stops
using the Quick-Start rate and continues to adjust its rate using
the standard congestion control mechanisms. For example, if the
DCCP sender was in slow-start prior to the Quick-Start Request, and
no packets were lost or ECN marked since that time, then the sender
continues in slow-start after exiting Quick-Start Mode until the
sender sees a packet loss, or congestion is reported.
2.4 Procedure when no response to a Quick-Start Request
As in TCP, if a Quick-Start Request is dropped (i.e., the Request or
Response is not delivered by the network) the DCCP sender MUST
Expires November 2009 [Page 9]
INTERNET DRAFT Quick-Start for DCCP June 2009
revert to the congestion control mechanisms it would have used if
the Quick-Start Request had not been approved. The connection is not
permitted to send a subsequent Quick-Start Request before expiry of
the current Quick-Start Interval (section 2.1.1).
2.5 Procedure when a packet is dropped while using Quick-Start
A lost or ECN-marked packet is an indication of potential network
congestion. The behaviour of a DCCP sender following a lost or ECN-
marked Quick-Start Packet or a lost feedback packet is specific to a
particular CCID (see section 3).
2.6 Interactions with Mobility and Signalled Path Changes
The use of Quick-Start may assist end hosts in determining when it
is appropriate to increase their rate following an explicitly
signalled change of the network path.
When an end host receives a signal from an upstream link/network
notifying it of a path change, the change could simultaneously
impact more than one flow, and may affect flows between multiple
endpoints. Senders should avoid responding immediately, since this
could result in unwanted synchronisation of signalling messages, and
control loops (e.g. a synchronised attempt to probe for a larger
congestion window), which may negatively impact the performance of
the network and transport sessions. In Quick-Start, this could
increase the rate of Quick-Start Requests, possibly incurring
additional router load, and may result in some requests not being
granted. A sender must ensure this does not generate an excessive
rate of Quick-Start Requests by using the method below:
A sender that has explicit information that the network path has
changed (e.g. a mobile IP binding update [RFC3344], [RFC3775])
SHOULD reset the Quick-Start Interval to its initial value
(specified in section 2.1).
The sender MAY also send a Quick-Start Request to determine a new
safe transmission rate, but must observe the following rules:
. It MUST NOT send a Quick-Start Request within a period less
than the initial Quick-Start Interval (Initial_QSI) since it
previously sent a Quick-Start Request. That is, it must wait
for at least a period of Initial_QSI after the previous
request, before sending a new Quick-Start Request.
. If it has not sent a Quick-Start Request within the previous
Initial_QSI period, it SHOULD defer sending a Quick-Start
Request for a randomly chosen period between 0 and the
Initial_QSI value in seconds. The random period should be
statistically independent between different hosts and between
different connections on the same host. This delay is to
mitigate the effect on router load of synchronised responses by
Expires November 2009 [Page 10]
INTERNET DRAFT Quick-Start for DCCP June 2009
multiple connections in response to a path change that affects
multiple connections.
Hosts do not generally have sufficient information to choose an
appropriate randomisation interval. This value was selected to
ensure randomisation of requests over the Quick-Start Interval. In
networks where a large number of senders may potentially be impacted
by the same signal, a larger value may be desirable (or methods may
be used to control this effect in the path change signalling).
2.7 Interactions with Path MTU Discovery
DCCP implementations are encouraged to support Path MTU Discovery
(PMTUD) when applications are able to use a DCCP packet size that
exceeds the default Path MTU [RFC4340], [RFC4821]. Quick-Start
Requests SHOULD NOT be sent with packets that are used as a PMTUD
Probe Packet, since these packets could be lost in the network
increasing the probability of loss of the request. It may therefore
be preferable to separately negotiate the PMTU and the use of Quick-
Start.
The DCCP protocol is datagram-based and therefore the size of the
segments that are sent is a function of application behaviour as
well as being constrained by the largest supported Path MTU.
2.8 Interactions with Middle boxes
A Quick-Start Request is carried in an IPv4 packet option or IPv6
extension header [RFC4782]. Interactions with network devices
(middle boxes) that inspect or modify IP options could therefore
lead to discard, ICMP error, or DCCP-Reset when attempting to
forward packets carrying a Quick-Start Request.
If a DCCP sender sends a DCCP-Request that also carries a Quick-
Start Request, and does not receive a DCCP-Response to the packet,
the DCCP sender SHOULD resend the DCCP-Request packet without
including a Quick-Start Request.
Similarly, if a DCCP sender receives a DCCP-Reset in response to a
DCCP-Request packet that also carries a Quick-Start Request, then
the DCCP sender SHOULD resend DCCP-Request packet without the
Quick-Start Request. The DCCP sender then ceases to use the Quick-
Start Mechanism for the remainder of the connection.
A DCCP sender that uses a Quick-Start Request within an established
connection and does not receive a response will treat this as non-
approval of the request. Successive unsuccessful attempts will
result in an exponential increase in the Quick-Start Interval
(section 2.2). If this grows to a value exceeding 64 seconds the
DCCP sender ceases to use the Quick-Start Mechanism for the
remainder of the connection.
Expires November 2009 [Page 11]
INTERNET DRAFT Quick-Start for DCCP June 2009
3. Mechanisms for Specific CCIDs
The following sections specify the use of Quick-Start with DCCP CCID
2, CCID 3, and for DCCP with TFRC-SP (as proposed for CCID 4).
3.1 Quick-Start for CCID 2
This section describes the Quick-Start mechanism to be used with
DCCP CCID 2 [RFC4341]. CCID 2 uses a TCP-like congestion control
mechanism.
3.1.1 The Quick-Start Request for CCID 2
A Quick-Start Request MAY be sent to allow the sender to determine
if it is safe to use a larger initial cwnd. This permits a faster
start-up of a new CCID 2 flow.
A Quick-Start Request MAY also be sent for an established connection
to request a higher sending rate after an idle period or
application-limited period (described in section 2.1). This allows a
receiver to use a larger cwnd than allowed with standard operation.
A Quick-Start Request that follows a reported loss or congestion
event MUST NOT request a Quick-Start rate that exceeds the largest
congestion window achieved by the CCID 2 connection since the last
packet drop (translated to a sending rate).
3.1.2 Sending a Quick-Start Response with CCID 2
A receiver processing a Quick-Start Request uses the method
described in Section 2.3. On receipt of a Quick-Start Request, the
receiver MUST send a Quick-Start Response (even if a receiver is
constrained by the ACK Ratio).
3.1.3 Using the Quick-Start Response with CCID 2
On receipt of a valid Quick-Start Response option, the sender MUST
send a Quick-Start Approved option [RFC4782] (see Section 2.3).
If the approved Quick-Start rate is less than current sending rate,
the sender does not enter the Quick-Start Mode, and continues using
the procedure defined in CCID 2.
If the approved Quick-Start rate at the sender exceeds the current
sending rate, the sender enters the Quick-Start Mode and continues
in the Quick-Start Mode for a maximum period of 1 RTT.
The sender sets its Quick-Start cwnd (QS_cwnd) as follows:
QS_cwnd = (R * T) / (s + H) (1)
Expires November 2009 [Page 12]
INTERNET DRAFT Quick-Start for DCCP June 2009
where R is the Rate Request in bytes per second, T is the measured
round-trip path delay (RTT), s is the packet size, and H is the
estimated DCCP/IP header size in bytes (e.g., 32 bytes for DCCP
layered directly over IPv4, but larger when using IPsec or IPv6).
A CCID 2 sender MAY then increase its cwnd to the QS_cwnd. The cwnd
should not be reduced (i.e., a QS_cwnd lower than cwnd should be
ignored, since the CCID 2 congestion control method already permits
this rate). CCID 2 is not a rate-paced protocol. Therefore, if the
QS_cwnd is used, the sending host MUST implement a suitable method
to pace the rate at which the Quick-Start Packets are sent until it
receives a DCCP-ACK for a packet sent during the Quick-Start Mode
[RFC4782]. The sending host SHOULD also record the previous cwnd and
note that the new cwnd has been determined by Quick-Start, rather by
other means (e.g. by setting a flag to indicate that it is in Quick-
Start Mode).
When the sender receives the first DCCP-ACK to a packet sent in the
Quick-Start Mode, it leaves the Quick-Start Mode and enters the
Validation Phase.
3.1.4 Quick-Start Validation Phase for CCID 2
A CCID 2 sender MAY continue to send at the paced Quick-Start Rate
while in the Validation Phase. It leaves the Validation Phase on
receipt of an ACK that acknowledges the last Quick-Start Packet, or
if the validation phase persists for a period that exceeds the
Quick-Start Validation Time of 1 RTT. It MUST then reduce the cwnd
to the actual flight size (the current amount of unacknowledged data
sent) [RFC4782], and uses the congestion control methods specified
for CCID 2.
3.1.5 Reported loss or congestion while using Quick-Start
A sender in the Quick-Start Mode (or Validation Phase) that detects
congestion (e.g. receives a feedback packet that reports new packet
loss or a packet with a congestion marking), MUST immediately leave
the Quick-Start Mode (or Validation Phase). It then resets the cwnd
to half the recorded previous cwnd and enters the congestion
avoidance phase described in [RFC4341].
In the absence of any feedback at the end of the Validation period,
the sender resets the cwnd to half the recorded previous cwnd and
enters the congestion avoidance phase.
3.1.6 CCID 2 Feedback Traffic on the Reverse Path
A CCID 2 receiver sends feedback for groups of received packets
[RFC4341]. Approval of a higher transmission rate using Quick-Start
will increase control traffic on the reverse path. A return path
that becomes congested could have a transient negative impact on
other traffic flows sharing the return link. The lower rate of
Expires November 2009 [Page 13]
INTERNET DRAFT Quick-Start for DCCP June 2009
feedback will then limit the achievable rate in the forward
direction.
3.2 Quick-Start for CCID 3
This section describes the Quick-Start mechanism to be used with
DCCP CCID 3 [RFC4342]. The rate-based congestion control mechanism
used by CCID 3 leads to specific issues that are addressed by Quick-
Start in this section.
3.2.1 The Quick-Start Request for CCID 3
A Quick-Start Request MAY be sent to allow the sender to determine
if it is safe to use a larger initial sending rate. This permits a
faster start-up of a new CCID 3 flow.
A Quick-Start Request MAY also be sent to request a higher sending
rate after an idle period (in which the nofeedback timer expires
[RFC5348]) or an application-limited period (described in section
2.1). This allows a receiver to increase the sending rate faster
than allowed with standard operation (i.e. faster than twice the
rate reported by a CCID 3 receiver in the most recent feedback
message).
The requested rate specified in a Quick-Start Request MUST NOT
exceed the TFRC-controlled sending rate [RFC4342] when this is
bounded by the current loss event rate (if any), either from
calculation at the sender or from feedback received from the
receiver. CCID 3 considers this rate is a safe response in the
presence of expected congestion.
3.2.2 Sending a Quick-Start Response with CCID 3
When processing a received Quick-Start Request, the receiver uses
the method described in Section 2.3. In addition, if a CCID 3
receiver uses the window counter to send periodic feedback messages,
then the receiver sets its local variable last_counter to the value
of the window counter reported by the segment containing the Quick-
Start Request. The next feedback message would then be sent when the
window_counter is greater or equal to last_counter + 4. If the CCID
3 receiver uses a feedback timer to send period feedback messages,
then the DCCP receiver MUST reset the CCID 3 feedback timer, causing
the feedback to be sent as soon as possible. This helps to align the
timing of feedback to the start and end of the period in which
Quick-Start Packets are sent, and will normally result in feedback
at a time that is approximately the end of the period when Quick-
Start Packets are received.
3.2.3 Using the Quick-Start Response with CCID 3
On receipt of a valid Quick-Start Response option, the sender MUST
send a Quick-Start Approved option [RFC4782] (see Section 2.3).
Expires November 2009 [Page 14]
INTERNET DRAFT Quick-Start for DCCP June 2009
If the approved Quick-Start rate is greater than the current sending
rate, the sender enters the Quick-Start Mode, otherwise it does not
enter the Quick-Start Mode and continues using the procedure defined
in CCID 3.
If loss or congestion is reported after sending the Quick-Start
Request, the sender also does not enter the Quick-Start Mode and
continues using the procedure defined in CCID 3.
If the approved Quick-Start rate exceeds the current sending rate,
the sender enters the Quick-Start Mode and continues in the Quick-
Start Mode for a maximum period of 1 RTT. The sender sets its Quick-
Start sending rate (QS_sendrate) as follows:
QS_sendrate = R * s/(s + H); (2)
where R the Rate Request in bytes per second, s is the packet size
[RFC4342], and H the estimated DCCP/IP header size in bytes (e.g.,
32 bytes for IPv4). A CCID 3 host MAY then increase its sending rate
to the QS_sendrate. The rate should not be reduced.
CCID 3 is a rate-paced protocol. Therefore, if the QS_sendrate is
used, the sending host MUST pace the rate at which the Quick-Start
Packets are sent over the next RTT. The sending host SHOULD also
record the previous congestion-controlled rate and note that the new
rate has been determined by Quick-Start rather by other means (e.g.
by setting a flag to indicate that it is in the Quick-Start Mode).
The sender exits the Quick-Start Mode after either:
* Receipt of a feedback packet acknowledging one or more Quick-Start
Packets,
* A period of 1 RTT after receipt of a Quick-Start Response,
or
* Detection of a loss or congestion event (see Section 3.2.5).
3.2.4 Quick-Start Validation Phase for CCID 3
After transmitting a set of Quick-Start Packets in the Quick Start
Mode (and providing that no loss or congestion marking is reported),
the sender enters the Quick-Start Validation Phase. A sender that
receives feedback that reports a loss or congestion event MUST
follow the procedures described in Section 3.2.5.
The sender MUST exit the Quick-Start Validation Phase on receipt of
feedback that acknowledges all packets sent in the Quick-Start Mode
(i.e. all Quick-Start Packets) or if the Validation Phase persists
for a period that exceeds the Quick-Start Validation Time of two
RTTs.
A sender that completes the Quick-Start Validation Phase with no
reported packet loss or congestion stops using the QS_sendrate and
Expires November 2009 [Page 15]
INTERNET DRAFT Quick-Start for DCCP June 2009
MUST recalculate a suitable sending rate using the standard
congestion control mechanisms [RFC4342].
If no feedback is received within the Quick-Start Validation Phase,
the sender MUST return to the minimum of the recorded original rate
(at the start of the Quick-Start Mode) and one half of the
QS_sendrate. The nofeedback timer is also reset.
3.2.5 Reported loss or congestion during the Quick-Start Mode or
Validation Phase
A sender in the Quick-Start Mode or Validation Phase that detects
congestion (e.g. receives a feedback packet that reports new packet
loss or a packet with a congestion marking) MUST immediately leave
the Quick-Start Mode or Validation Phase and enter the congestion
avoidance phase [RFC4342]. This implies re-calculating the sending
rate, X, as required by RFC4342:
X = max(min(X_calc, 2*X_recv), s/t_mbi);
where X_calc is the transmit rate calculated by the throughput
equation, X_recv is the reported receiver rate, s is the packet size
and t_mbi is the maximum backoff interval of 64 seconds.
The current specification of TFRC [RFC5348], which obsoletes RFC
3448, uses a set of X_recv values and uses the maximum of the set
during data-limited intervals. This calculates the sending rate, X
as:
X = max(min(X_calc, recv_limit),s/t_mbi);
where recv_limit could be max(X_recv_set) or 2*max(X_recv_set)
depending on whether there was a new loss event during a data-
limited interval, or no loss event during a data-limited interval
respectively. When the sender is not data-limited, the recv_limit is
set to 2*max(X_recv_set).
A sender using RFC4342 updated by [RFC5348], calculates the sending
rate, X, using the above formula normatively defined in [RFC5348].
3.2.6 CCID 3 Feedback Traffic on the Reverse Path
A CCID 3 receiver sends feedback at least once each RTT [RFC4342].
Use of Quick-Start is therefore not expected to significantly
increase control traffic on the reverse path.
3.3 Quick-Start for CCID 4
This section describes the Quick-Start mechanism to be used when
DCCP uses TFRC-SP [RFC4828] in place of TFRC [RFC5348], as specified
in CCID 4 [ID.CCID4]. CCID 4 is similar to CCID 3 except that a
sender using CCID 4 is limited to a maximum of 100 packets/second.
Expires November 2009 [Page 16]
INTERNET DRAFT Quick-Start for DCCP June 2009
The Quick-Start procedure defined below therefore resembles that for
CCID 3.
3.3.1 The Quick-Start Request for CCID 4
The procedure for sending a Quick-Start Request using CCID 4 is the
same as for CCID 3, defined in section 3.2.1. In addition, the
requested rate MUST be less than or equal to the equivalent of a
sending rate of 100 packets per second [RFC4828 CCID 4 [RFC4828]
specifies that the allowed sending rate derived from the TCP
throughput equation is reduced by a factor that accounts for packet
header size.
3.3.2 Sending a Quick-Start Response with CCID 4
This procedure is the same as for CCID 3, defined in section 3.2.2.
3.3.3 Using the Quick-Start Response with CCID 4
This procedure is the same as for CCID 3, defined in sections 3.2.3,
3.2.4, and 3.2.5, except that the congestion control procedures is
updated to use TFRC-SP [RFC4828].
A CCID 4 sender does not need to account for headers a second time
when translating the approved Quick-Start rate into an allowed
sending rate (as described in section 5 of [ID.CCID4].
3.3.4 Reported loss or congestion while using Quick-Start
This procedure is the same as for CCID 3, defined in 3.2.5, except
that the congestion control procedures is updated to use TFRC-SP
[RFC4828].
3.3.5 CCID 4 Feedback Traffic on the Reverse Path
A CCID 4 receiver sends feedback at least once each RTT. Use of
Quick-Start is therefore not expected to significantly increase
control traffic on the reverse path.
4. Discussion of Issues
The considerations for using Quick-Start with DCCP are not
significantly different to those for Quick-Start with TCP. The
document does not modify the router behaviour specified for Quick-
Start.
4.1 Over-run and the Quick-Start Validation Phase
The less frequent feedback of DCCP raises an issue in that a sender
using Quick-Start may continue to use the rate specified by a Quick-
Start Response for a period that exceeds one path round trip time
(i.e., that which TCP would have used). This over-run is a result of
the less frequent feedback interval used by DCCP (i.e., CCID 2 may
Expires November 2009 [Page 17]
INTERNET DRAFT Quick-Start for DCCP June 2009
delay feedback by at most one half cwnd and CCID 3 and CCID 4
provide feedback at least once per RTT). In the method specified by
this document, the Quick-Start Validation Phase bounds this over-run
to be not more than an additional 2 RTTs.
The currently selected method is chosen as a compromise that
reflects the need to terminate quickly following the loss of a
feedback packet, and the need to allow sufficient time for end host
and router processing, as well as the different perceptions of the
path RTT held at the sender and receiver. Any reported loss or
congestion results in immediate action without waiting for
completion of the Quick-Start Validation period.
4.2 Experimental Status
There are many cases in which Quick-Start Requests would not be
approved [RFC4782]. These include communication over paths
containing routers, IP tunnels, MPLS paths, and the like, that do
not support Quick-Start. These cases also include paths with
routers or middleboxes that drop packets containing IP options (or
IPv6 extensions). Quick-Start Requests could be difficult to
approve over paths that include multi-access layer-two networks.
Transient effects could arise when the transport protocol packets
associated with a connection are multiplexed over multiple parallel
(sometimes known as alternative) links or network-layer paths, and
Quick-Start is used, since it will be effective on only one of the
paths, but could lead to increased traffic on all paths.
A CCID 2 sender using Quick-Start can increase the control traffic
on the reverse path, which could have a transient negative impact on
other traffic flows sharing the return link (section 3.1.5). The
lower rate of feedback will then limit the achievable rate in the
forward direction.
[RFC4782] also describes environments where the Quick-Start
mechanism could fail with false positives, with the sender
incorrectly assuming that the Quick-Start Request had been approved
by all of the routers along the path. As a result of these
concerns, and as a result of the difficulties and the seeming
absence of motivation for routers, such as core routers, to deploy
Quick-Start, Quick-Start has been proposed as a mechanism that could
be of use in controlled environments, and not as a mechanism that
would be intended or appropriate for ubiquitous deployment in the
global Internet.
Further experimentation would be required to confirm the deployment
of Quick-Start and to investigate performance issues that may arise,
prior to any recommendation for use over the general Internet.
Expires November 2009 [Page 18]
INTERNET DRAFT Quick-Start for DCCP June 2009
5. IANA Considerations
This document requires IANA involvement for the assignment of a DCCP
Option Type from the DCCP Option Types Registry. This Option is
applicable to all CCIDs and is known as the "Quick-Start Response"
Option and is defined in Section 2.2.1. It specifies a length value
in the format used for options numbered 32-128.
6. Acknowledgments
The author gratefully acknowledges the previous work by Sally Floyd
to identify issues that impact Quick-Start for DCCP, and her
comments to improve this document. We also acknowledge comments and
corrections from Pasi Sarolahti, Vincent Roca, Mark Allman, Michael
Scharf, Sally Floyd, and others in the IETF DCCP WG.
7. Security Considerations
Security issues are discussed in [RFC4782]. Middlebox deployment
issues are also highlighted in section 2.9. No new security issues
are raised within this document.
8. References
8.1 Normative References
[RFC2119] Bradner, S., "Key Words for Use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, 1997.
[RFC4340] Kohler, E., Handley, M., and S. Floyd, "Datagram
Congestion Control Protocol (DCCP)", RFC 4340, March 2006.
[RFC4341] Floyd, S. and E. Kohler, "Profile for Datagram Congestion
Control Protocol (DCCP) Congestion Control ID 2: TCP-like Congestion
Control", RFC 4341, March 2006.
[RFC4342] Floyd, S., Kohler, E., and J. Padhye, "Profile for
Datagram Congestion Control Protocol (DCCP) Congestion Control ID 3:
TCP-Friendly Rate Control (TFRC)", RFC 4342, March 2006.
[RFC4782] Floyd, S., Allman, M., Jain, A., and P. Sarolahti, "Quick-
Start for TCP and IP", RFC 4782, January 2007.
[RFC4828] Floyd, S. and E. Kohler, "TCP Friendly Rate Control
(TFRC): The Small-Packet (SP) Variant", RFC 4828, April 2007.
[RFC5348] Floyd, S., Padhye, J., Widmer, J., "TCP Friendly Rate
Control (TFRC): Protocol Specification", RFC 5348, September 2008.
Expires November 2009 [Page 19]
INTERNET DRAFT Quick-Start for DCCP June 2009
8.2 Informative References
[ID.CCID4] Floyd, S., Kohler, E., "Profile for Datagram Congestion
Control Protocol (DCCP) Congestion ID 4: TCP-Friendly Rate Control
for Small Packets (TFRC-SP)", IETF Work In Progress, 2007.
[RFC3344] Perkins, C., Ed., "IP Mobility Support for IPv4", RFC
3344, August 2002.
[RFC3775] Johnson, D., Perkins, C., and J. Arkko, "Mobility Support
in IPv6", RFC 3775, June 2004.
[RFC3390] Allman, M., Floyd, S., Partridge, C., "Increasing TCP's
Initial Window", RFC 3390, October 2002.
[RFC4821] Mathis, M. and J. Heffner, "Packetization Layer Path MTU
Discovery", RFC 4821, March 2007.
9. Authors' Addresses
Godred Fairhurst
School of Engineering
University of Aberdeen
Aberdeen, AB24 3UE
Scotland, UK
Email: gorry@erg.abdn.ac.uk
URI: http://www.erg.abdn.ac.uk/users/gorry
Arjuna Sathiaseelan
School of Engineering
University of Aberdeen
Aberdeen, AB24 3UE
Scotland, UK
Email: arjuna@erg.abdn.ac.uk
URI: http://www.erg.abdn.ac.uk/users/arjuna
10. Copyright Notice
Copyright (c) 2009 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents in effect on the date of
publication of this document (http://trustee.ietf.org/license-info).
Please review these documents carefully, as they describe your
rights and restrictions with respect to this document.
This document may contain material from IETF Documents or IETF
Contributions published or made publicly available before November
10, 2008. The person(s) controlling the copyright in some of this
Expires November 2009 [Page 20]
INTERNET DRAFT Quick-Start for DCCP June 2009
material may not have granted the IETF Trust the right to allow
modifications of such material outside the IETF Standards Process.
Without obtaining an adequate license from the person(s) controlling
the copyright in such materials, this document may not be modified
outside the IETF Standards Process, and derivative works of it may
not be created outside the IETF Standards Process, except to format
it for publication as an RFC or to translate it into languages other
than English.
Expires November 2009 [Page 21]
INTERNET DRAFT Quick-Start for DCCP June 2009
-------------------------------------------------------------------
[RFC EDITOR NOTE:
This section must be deleted prior to publication]
DOCUMENT HISTORY
Individual Draft 00
This is the first presentation of this document.
Individual Draft 01
This includes fixes for NiTs (thanks Pasi)
It also includes a note on initial rates in 2.1
All mention of packet loss now qualified with loss/congestion.
It adds supports for CCID 2.
It also defines the Quick-Start Interval as a way of controlling the
rate at which hosts may issue Quick-Start requests.
Individual Draft 02 - Draft intended for more general review
Resolution of many minor outstanding editorial issues.
Includes feedback on a longer Quick-Start period from Mark Allman.
Includes new section on the interaction with middleboxes.
CCID 2 and CCID 3 text now use the same style.
Added description for CCID 4, based on CCID 3.
Added clarification of PMTUD interaction.
Reorganised to create a section on the QS Interval
Rewritten sections on what to do after loss/congestion
Clarified path change triggers (e.g. from mobility binding updates)
There are no currently known remaining issues to be addressed.
Individual Draft 03
This includes fixes for NiTs, especially to shorten some parts of
text.
It includes some additional clarification based on the progress of
RFC3448.bis.
Replaced reference to Faster Restart.
Change to paragraph on mobility usage.
Working Group Draft 00
Title change only.
Working Group Draft 01 : Following WG feedback
Issued following feedback on Quick-Start issues and various comments
from Michael Scharf. CCID 2 feedback expected in 1.5 RTTs (allowing
for less frequent ACKs). TFRC-SP is now cited in CCID 4 discussion.
Included more on the rationale of the validation phase and the
mobility trigger randomisation interval of 6 seconds.
Note: This I-D must be Last-Called in both TSV and DCCP.
Working Group Draft 02
Clarified text on QS Interval.
Expires November 2009 [Page 22]
INTERNET DRAFT Quick-Start for DCCP June 2009
Harmonised the Quick-Start mode across all CCIDs.
Introduced the concept of the Quick_Start Validation Phase for CCID
2, as a counter to using a less frequent acknowledgment policy. This
behavior is now similar to that of CCID 3 in this regard.
A new subsection was added in Section 2 to describe the validation
for all CCIDs.
Working Group Draft 03
This revision renumbered some sections to improve organisation.
Revised ID following feedback from Vincent Roca.
Revised ID following feedback from Sally Floyd.
Working Group Draft 04 - based on Pasi's comments during WGLC
The constant 6 seconds was replaced by the text constant
Initital_QSI.
QSPrev_Interval has been removed - to avoid the ambiguity concerning
when to reset the value.
The max(Initital_QSI..) term has been removed, since the value can
never anyway be less than Initital_QSI, and the text now reflects
this.
The CCID 3 equations have been simplified, by removing a smaller
term from a MIN(,) expression - again this value can not change the
calculation.
The QS Approve method was mentioned in section 2 for completeness.
Working Group Draft 04 - based on Pasi's comments aftre WGLC
Fixed section number ref in IANA section.
Note: This I-D must be Last-Called in both TSV and DCCP.
[END of RFC EDITOR NOTE]
Expires November 2009 [Page 23]
| PAFTECH AB 2003-2026 | 2026-04-22 12:59:46 |