One document matched: draft-ietf-ccamp-gmpls-te-mib-03.txt
Differences from draft-ietf-ccamp-gmpls-te-mib-02.txt
CCAMP Working Group Thomas D. Nadeau
Internet Draft Cisco Systems, Inc.
Expires: May 2004
Cheenu Srinivasan
Bloomberg L.P.
Adrian Farrel
Old Dog Consulting
Tim Hall
Ed Harrison
Data Connection Ltd.
November 2003
Generalized Multiprotocol Label Switching (GMPLS) Traffic
Engineering Management Information Base
draft-ietf-ccamp-gmpls-te-mib-03.txt
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Abstract
This memo defines an experimental portion of the Management
Information Base (MIB) for use with network management protocols in
the Internet community. In particular, it describes managed objects
for Generalized Multiprotocol Label Switching (GMPLS) based traffic
engineering.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 1]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
Table of Contents
1. Introduction 2
1.1. Migration Strategy 3
2. Terminology 3
3. The SNMP Management Framework 3
4. Outline 4
4.1. Summary of GMPLS Traffic Engineering MIB Module 4
5. Brief Description of GMPLS TE MIB Objects 4
5.1. gmplsTunnelTable 4
5.2. gmplsTunnelHopTable 5
5.3. gmplsTunnelARHopTable 5
5.4. gmplsTunnelCHopTable 5
5.5. gmplsTunnelErrorTable 5
5.6. gmplsTunnelPerfTable 5
6. Cross-referencing to the mplsLabelTable 5
7. Example of GMPLS Tunnel Setup 6
8. GMPLS Traffic Engineering MIB Definitions 8
9. Security Considerations 36
10. Acknowledgments 37
11. References 37
11.1. Normative Refenerces 37
11.2. Informational References 39
12. Authors' Addresses 39
13. Full Copyright Statement 40
14. Intellectual Property Notice 41
15. Changes and Pending Work 41
15.1. Pending Work 41
1. Introduction
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects for modeling a
Generalized Multi-Protocol Label Switching (GMPLS) [GMPLSArch] based
traffic engineering. The tables and objects defined in this document
extend those defined in the equivalent document for MPLS traffic
engineering [TEMIB], and management of GMPLS traffic engineering is
built on management of MPLS traffic engineering.
This MIB module should be used in conjunction with the companion
document [GMPLSLSRMIB] for GMPLS based traffic engineering
configuration and management.
Comments should be made direct to the CCAMP mailing list at
ccamp@ops.ietf.org.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119, reference
[RFC2119].
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 2]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
1.1. Migration Strategy
This MIB extends the traffic engineering MIB defined for use with
MPLS [TEMIB]. It provides additions for support of GMPLS tunnels.
The companion document modeling and managing GMPLS based LSRs
[GMPLSLSRMIB] extends MPLS LSR MIB [LSRMIB] with the same intentions.
Textual conventions and OBJECT-IDENTIFIERS are defined in [TCMIB] and
[GMPLSTCMIB].
2. Terminology
This document uses terminology from the MPLS architecture document
[RFC3031], from the GMPLS architecture document [GMPLSArch], and from
the MPLS Label Switch Router MIB [LSRMIB]. Some frequently used terms
are described next.
An explicitly routed LSP (ERLSP) is referred to as a GMPLS tunnel. It
consists of in-segment(s) and/or out-segment(s) at the egress/ingress
LSRs, each segment being associated with one GMPLS enabled interface.
These are also referred to as tunnel segments.
Additionally, at an intermediate LSR, we model a connection as
consisting of one or more in-segments and/or one or more out-
segments. The binding or interconnection between in-segments and out-
segments in performed using a cross-connect.
These segment and cross-connect objects are defined in the MPLS Label
Switch Router MIB [LSRMIB], but see also the GMPLS Label Switch
Router MIB [GMPLSLSRMIB] for the GMPLS-specific extensions to these
objects.
3. The SNMP Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a
MIB module that is compliant to the SMIv2, which is described in STD
58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC
2580 [RFC2580].
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 3]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
4. Outline
Support for GMPLS traffic-engineered tunnels requires the following
configuration.
- Setting up tunnels with appropriate MPLS configuration parameters
using [TEMIB].
- Extending the tunnels with GMPLS configuration parameters.
- Configuring tunnel loose and strict source routed hops.
These actions may need to be accompanied with corresponding actions
using [LSRMIB] and [GMPLSLSRMIB] to establish and configure tunnel
segments, if this is done manually. Also, the in-segment and out-
segment performance tables, mplsInSegmentPerfTable and
mplsOutSegmentPerfTable [LSRMIB], should be used to determine
performance of the tunnels and tunnel segments although it should be
noted that those tables may not be appropriate for measuring
performance on some times of GMPLS links.
4.1. Summary of GMPLS Traffic Engineering MIB Module
The MIB objects for performing the actions listed above that cannot
be performed solely using the MIB objects defined in [TEMIB] consist
of the following tables.
- Tunnel Table (gmplsTunnelTable) for providing GMPLS-specific
tunnel configuration parameters.
- Tunnel specified, actual, and computed hop tables
(gmplsTunnelHopTable, gmplsTunnelARHopTable, and
gmplsTunnelCHopTable) for providing additional configuration of
strict and loose source routed tunnel hops.
- Performance and error reporting tables (gmplsTunnelPerfTable and
gmplsTunnelErrorTable).
These tables are described in the subsequent sections.
5. Brief Description of GMPLS TE MIB Objects
The objects described in this section support the functionality
described in [RFC3473] and [RFC3472] for GMPLS tunnels.
The tables support both manually configured and signaled tunnels.
5.1. gmplsTunnelTable
The gmplsTunnelTable extends the MPLS traffic engineering MIB to
allow GMPLS tunnels to be created between an LSR and a remote
endpoint, and existing GMPLS tunnels to be reconfigured or removed.
Note that we only support point-to-point tunnel segments, although
multi-point-to-point and point-to-multi-point connections are
supported by an LSR acting as a cross-connect.
Each tunnel can thus have one out-segment originating at an LSR
and/or one in-segment terminating at that LSR.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 4]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
5.2. gmplsTunnelHopTable
The gmplsTunnelHopTable is used to indicate additional parameters for
the hops, strict or loose, of a GMPLS tunnel defined in
gmplsTunnelTable, when it is established using signaling. Multiple
tunnels may share the same hops by pointing to the same entry in this
table.
5.3. gmplsTunnelARHopTable
The gmplsTunnelARHopTable is used to indicate the actual hops
traversed by a tunnel as reported by the signaling protocol after the
tunnel is setup. The support of this table is optional since not all
GMPLS signaling protocols support this feature.
5.4. gmplsTunnelCHoptable
The gmplsTunnelCHopTable lists the actual hops computed by a
constraint-based routing algorithm based on the gmplsTunnelHopTable.
The support of this table is optional since not all implementations
support computation of hop list using a constraint-based routing
protocol.
5.5. gmplsTunnelErrorTable
The gmplsTunnelErrorTable provides access to information about the
last error that occurred on each tunnel known about by the MIB. It
indicates the nature of the error, when and how it was reported and
can give recovery advice through a display string.
5.6. gmplsTunnelPerfTable
gmplsTunnelPerfTable provides additional counters to measure the
performance of GMPLS tunnels in which packets are visible. It
supplements the counters in mplsTunnelPerfTable and augments
gmplsTunnelTable.
Note that not all counters may be appropriate or available for some
types of tunnel.
6. Cross-referencing to the mplsLabelTable
The gmplsLabelTable is found in a MIB module in [GMPLSLSRMIB] and
provides a way to model labels in a GMPLS system where labels might
not be simple 32 bit integers.
The hop tables in this document (gmplsHopTable, gmplsCHopTable and
gmplsARHopTable) use arbitrary indexes to point to entries in the
mplsLabelTable to indicate specific label values.
Since the primary indexes into gmplsLabelTable are the interface
index and a simple 32 bit integer (gmplsLabelIndex), in systems where
the nature of a label is well-known, and where the label can safely
be encoded as a 32 bit integer (for example a conventional MPLS
system), the gmplsLabelTable does not need to be supported in the
code implementation and the index pointers to the gmplsLabelTable
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 5]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
(gmplsTunnelHopExplicitLabel, gmplsTunnelHopExpRvrsLabel,
gmplsTunnelCHopExplicitLabel, gmplsTunnelCHopExpRvrsLabel,
gmplsTunnelARHopExplicitLabel, gmplsTunnelARHopExpRvrsLabel)
may be replaced with the direct label values.
This provides both a good way to support legacy systems that
implement the previous version of this MIB [TEMIB], and a significant
simplification in GMPLS systems that are limited to a single, simple
label type.
Note that gmplsLabelTable supports concatenated labels through the
use of a label sub-index (gmplsLabelSubindex).
7. Example of GMPLS Tunnel Setup
This section contains an example of which MIB objects should be
modified to create a GMPLS tunnel. This example shows a best effort,
loosely routed, bidirectional traffic engineered tunnel, which spans
two hops of a simple network, uses Generalized Label requests with
Lambda encoding, has label recording and shared link layer
protection. Note that these objects should be created on the "head-
end" LSR.
First in the mplsTunnelTable:
{
mplsTunnelIndex = 1,
mplsTunnelInstance = 1,
mplsTunnelIngressLSRId = 123.123.125.1,
mplsTunnelEgressLSRId = 123.123.126.1,
mplsTunnelName = "My first tunnel",
mplsTunnelDescr = "Here to there and back again",
mplsTunnelIsIf = true (1),
mplsTunnelXCPointer = mplsXCIndex.3.0.0.12,
mplsTunnelSignallingProto = none (1),
mplsTunnelSetupPrio = 0,
mplsTunnelHoldingPrio = 0,
mplsTunnelSessionAttributes = recordRoute (4),
mplsTunnelOwner = snmp (2),
mplsTunnelLocalProtectInUse = false (0),
mplsTunnelResourcePointer = mplsTunnelResourceIndex.6,
mplsTunnelInstancePriority = 1,
mplsTunnelHopTableIndex = 1,
mplsTunnelPrimaryInstance = 0,
mplsTunnelIncludeAnyAffinity = 0,
mplsTunnelIncludeAllAffinity = 0,
mplsTunnelExcludeAnyAffinity = 0,
mplsTunnelPathInUse = 1,
mplsTunnelRole = head(1),
mplsTunnelRowStatus = createAndWait (5),
}
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 6]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
In gmplsTunnelTable(1,1,123.123.125.1,123.123.126.1):
{
gmplsTunnelUnnumIf = true (1),
gmplsTunnelAttributes = labelRecordingRequired (1),
gmplsTunnelLSPEncoding = tunnelLspLambda (8),
gmplsTunnelSwitchingType = lsc (150),
gmplsTunnelLinkProtection = shared (2),
gmplsTunnelGPid = lambda (37),
gmplsTunnelDirection = bidirectional (1)
gmplsTunnelSecondary = false(0),
gmplsTunnelPathComp = explicit(2),
gmplsTunnelUpNotRecip = 0x7B7B7D01,
gmplsTunnelDownNotRecip = 0x00000000,
gmplsTunnelAdminStatusFlags = 0
}
Entries in the mplsTunnelResourceTable, mplsTunnelHopTable and
gmplsTunnelHopTable are created and activated at this time.
In mplsTunnelResourceTable:
{
mplsTunnelResourceIndex = 6,
mplsTunnelResourceMaxRate = 0,
mplsTunnelResourceMeanRate = 0,
mplsTunnelResourceMaxBurstSize = 0,
mplsTunnelResourceRowStatus = createAndGo (4)
}
The next two instances of mplsTunnelHopEntry are used to denote the
hops this tunnel will take across the network.
The following denotes the beginning of the network, or the first hop.
We have used the fictitious LSR identified by "123.123.125.1" as our
example head-end router.
In mplsTunnelHopTable:
{
mplsTunnelHopListIndex = 1,
mplsTunnelPathOptionIndex = 1,
mplsTunnelHopIndex = 1,
mplsTunnelHopAddrType = ipV4 (1),
mplsTunnelHopIpv4Addr = 123.123.125.1,
mplsTunnelHopIpv4PrefixLen = 9,
mplsTunnelHopType = strict (1),
mplsTunnelHopRowStatus = createAndWait (5),
}
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 7]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
The following denotes the end of the network, or the last hop in our
example. We have used the fictitious LSR identified by
"123.123.126.1" as our end router.
In mplsTunnelHopTable:
{
mplsTunnelHopListIndex = 1,
mplsTunnelPathOptionIndex = 1,
mplsTunnelHopIndex = 2,
mplsTunnelHopAddrType = ipV4 (1),
mplsTunnelHopIpv4Addr = 123.123.126.1,
mplsTunnelHopIpv4PrefixLen = 9,
mplsTunnelHopType = loose (2),
mplsTunnelHopRowStatus = createAndGo (4)
}
Now an associated entry in the gmplsTunnelHopTable is created to
provide additional GMPLS hop configuration indicating that the first
hop is an unnumbered link using explicit forward and reverse labels.
In gmplsTunnelHopTable(1,1,1):
{
gmplsTunnelHopLabelStatuses = forwardPresent(0)
+reversePresent(1),
gmplsTunnelHopExplicitLabel = gmplsLabelInterface.1,
gmplsTunnelHopExpRvrsLabel = gmplsLabelInterface.2
}
The first hop is now activated:
In mplsTunnelHopTable(1,1,1):
{
mplsTunnelHopRowStatus = active (1)
}
No gmplsTunnelHopEntry is created for the second hop as it contains
no special GMPLS features.
Finally the mplsTunnelEntry is activated:
In mplsTunnelTable(1,1,123.123.125.1,123.123.126.1)
{
mplsTunnelRowStatus = active(1)
}
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 8]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
8. GMPLS Traffic Engineering MIB Definitions
GMPLS-TE-STD-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE
Integer32, Unsigned32, Counter32,
Counter64, IpAddress
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
TruthValue, TimeStamp, DisplayString
FROM SNMPv2-TC
InetAddressIPv4, InetAddressIPv6
FROM INET-ADDRESS-MIB
mplsTunnelIndex, mplsTunnelInstance, mplsTunnelIngressLSRId,
mplsTunnelEgressLSRId, mplsTunnelHopListIndex,
mplsTunnelHopPathOptionIndex, mplsTunnelHopIndex,
mplsTunnelARHopListIndex, mplsTunnelARHopIndex,
mplsTunnelCHopListIndex, mplsTunnelCHopIndex,
mplsTunnelEntry, mplsTunnelSignallingProto
FROM MPLS-TE-STD-MIB
gmplsStdMIB
FROM GMPLS-TC-STD-MIB
;
gmplsTeStdMIB MODULE-IDENTITY
LAST-UPDATED
"200310300900Z" -- 30 October 2003 9:00:00 GMT"
ORGANIZATION
"Common Control And Management Protocols (CCAMP)
Working Group"
CONTACT-INFO
" Thomas D. Nadeau
Cisco Systems, Inc.
Email: tnadeau@cisco.com
Cheenu Srinivasan
Bloomberg L.P.
Email: cheenu@bloomberg.net
Adrian Farrel
Old Dog Consulting
Email: adrian@olddog.co.uk
Ed Harrison
Data Connection Ltd.
Email: ed.harrison@dataconnection.com
Tim Hall
Data Connection Ltd.
Email: timhall@dataconnection.com
Comments about this document should be emailed direct to the
CCAMP working group mailing list at ccamp@ops.ietf.org"
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 9]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
DESCRIPTION
"This MIB module contains managed object definitions
for GMPLS Traffic Engineering (TE).
Copyright (C) The Internet Society (2003). This
version of this MIB module is part of RFCXXX; see
the RFC itself for full legal notices."
-- Revision history.
REVISION
"200310300900Z" -- 30 October 2003 09:00:00 GMT
DESCRIPTION
"Initial revision, published as part of RFC XXXX."
::= { gmplsStdMIB xx }
-- Top level components of this MIB.
-- Notifications
-- no notifications are currently defined.
gmplsTeNotifications OBJECT IDENTIFIER ::= { gmplsTeStdMIB 0 }
-- tables, scalars
gmplsTeScalars OBJECT IDENTIFIER ::= { gmplsTeStdMIB 1 }
gmplsTeObjects OBJECT IDENTIFIER ::= { gmplsTeStdMIB 2 }
-- conformance
gmplsTeConformance OBJECT IDENTIFIER ::= { gmplsTeStdMIB 3 }
-- GMPLS Tunnel scalars.
gmplsTunnelsConfigured OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of GMPLS tunnels configured on this
device. A GMPLS tunnel is considered configured if
an entry for the tunnel exists in the
gmplsTunnelTable and the associated
mplsTunnelRowStatusis active(1)."
::= { gmplsTeScalars 1 }
gmplsTunnelsActive OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of GMPLS tunnels active on this device.
A GMPLS tunnel is considered active if there is an
entry in the gmplsTunnelTable and the associated
mplsTunnelOperStatus for the tunnel is up(1)."
::= { gmplsTeScalars 2 }
-- End of GMPLS Tunnel scalars.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 10]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
-- GMPLS tunnel table.
gmplsTunnelTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsTunnelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The gmplsTunnelTable 'extends' the mplsTunnelTable.
It allows GMPLS tunnels to be created between an LSR
and a remote endpoint, and existing tunnels to be
reconfigured or removed.
Note that only point-to-point tunnel segments are
supported, although multi-point-to-point and point-
to-multi-point connections are supported by an LSR
acting as a cross-connect. Each tunnel can thus have
one out-segment originating at this LSR and/or one
in-segment terminating at this LSR.
The row status of an entry in this table is
controlled by mplsTunnelRowStatus in the
corresponding entry in mplsTunnelTable. That is,
it is not permitted to create a row in this table,
nor to modify an existing row, when the
corresponding mplsTunnelRowStatus has value
active(1).
The exception to this rule is the gmplsTunnelAdminStatusFlags
object, which can be modified whilst the tunnel is active."
::= { gmplsTeObjects 1 }
gmplsTunnelEntry OBJECT-TYPE
SYNTAX GmplsTunnelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table in association with the
corresponding entry in the mplsTunnelTable
represents a GMPLS tunnel.
An entry can be created by a network administrator
or by an SNMP agent as instructed by a signaling
protocol."
INDEX {
mplsTunnelIndex,
mplsTunnelInstance,
mplsTunnelIngressLSRId,
mplsTunnelEgressLSRId
}
::= { gmplsTunnelTable 1 }
GmplsTunnelEntry ::= SEQUENCE {
gmplsTunnelUnnumIf TruthValue,
gmplsTunnelAttributes BITS,
gmplsTunnelLSPEncoding Integer32,
gmplsTunnelSwitchingType Integer32,
gmplsTunnelLinkProtection BITS,
gmplsTunnelGPid Integer32,
gmplsTunnelSecondary TruthValue,
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 11]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
gmplsTunnelDirection INTEGER,
gmplsTunnelPathComp INTEGER,
gmplsTunnelUpNotRecip IpAddress,
gmplsTunnelDownNotRecip IpAddress,
gmplsTunnelAdminStatusFlags BITS
}
gmplsTunnelUnnumIf OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Denotes whether or not this tunnel corresponds to an
unnumbered interface represented in the interfaces
group table.
This object is only used if mplsTunnelIsIf is set to
'true'.
If both this object and the mplsTunnelIsIf object
are set to 'true', the originating LSR adds an
LSP_TUNNEL_INTERFACE_ID object to the outgoing Path
message.
This object contains information that is only used
by the terminating LSR."
REFERENCE
"1. draft-ietf-mpls-crldp-unnum-06.txt - Signalling
Unnumbered Links in CR-LDP, Kompella, K., Rekhter, Y.
and Kullberg, A., June 2002.
2. Signalling Unnumbered Links in RSVP-TE, Kompella, K.
and Rekhter, Y., RFC 3477, January 2003."
DEFVAL { false }
::= { gmplsTunnelEntry 1 }
gmplsTunnelAttributes OBJECT-TYPE
SYNTAX BITS {
labelRecordingDesired (0)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This bitmask indicates optional parameters for this
tunnel. These bits should be taken in addition to
those defined in mplsTunnelSessionAttributes in
order to determine the full set of options to be
signaled (for example SESSION_ATTRIBUTES flags in
RSVP-TE).
The following describes these bitfields:
labelRecordingDesired
This flag indicates that label information should be
included when doing a route record. This bit is not
valid unless the recordRoute bit is set."
REFERENCE
"1. RSVP-TE: Extensions to RSVP for LSP Tunnels,
Awduche et al, RFC 3209, December 2001."
DEFVAL { { } }
::= { gmplsTunnelEntry 2 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 12]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
gmplsTunnelLSPEncoding OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the encoding of the LSP being
requested.
A value of zero indicates that GMPLS signaling is
not in use. Some objects in this MIB module may be
of use for MPLS signaling extensions that do not use
GMPLS signaling. By setting this object to zero, an
application may indicate that only those objects
meaningful in MPLS should be examined.
The values to use are currently defined in
Generalized Multi-Protocol Label Switching (GMPLS)
Signaling Functional Description, RFC 3471. Further
values may be defined in future RFCs.
tunnelLspPacket (1),
tunnelLspEthernet (2),
tunnelLspAnsiEtsiPdh (3),
-- the value 4 is deprecated
tunnelLspSdhSonet (5),
-- the value 6 is deprecated
tunnelLspDigitalWrapper (7),
tunnelLspLambda (8),
tunnelLspFiber (9),
-- the value 10 is deprecated
tunnelLspFiberChannel (11)"
REFERENCE
"1. Berger, L., et al., Generalized Multi-Protocol
Label Switching (GMPLS) Signaling Functional
Description, RFC 3471, January 2003."
DEFVAL { 0 }
::= { gmplsTunnelEntry 3 }
gmplsTunnelSwitchingType OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the type of switching that should be performed on
a particular link. This field is needed for links that
advertise more than one type of switching capability. Values
of this object are as the Switching Capability field defined
in Internet Draft OSPF Extensions in Support of Generalized
MPLS. Further values may be defined in future RFCs.
unknown (0),
psc1 (1),
psc2 (2),
psc3 (3),
psc4 (4),
l2sc (51),
tdm (100),
lsc (150),
fsc (200)
This object is only meaningful if
gmplsTunnelLSPEncoding is not set to 0."
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 13]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
REFERENCE
"1. Kompella, K., et al., OSPF Extensions in Support
of Generalized MPLS, draft-ietf-ccamp-ospf-gmpls-
extensions-07.txt, May 2002, work in progress.
2. Berger, L., et al., Generalized Multi-Protocol
Label Switching (GMPLS) Signaling Functional
Description, RFC 3471, January 2003."
DEFVAL { 0 }
::= { gmplsTunnelEntry 4 }
gmplsTunnelLinkProtection OBJECT-TYPE
SYNTAX BITS {
extraTraffic(0),
unprotected(1),
shared (2),
dedicatedOneToOne (3),
dedicatedOnePlusOne(4),
enhanced(5)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This bitmask indicates the level of link protection
required. A value of zero (no bits set) indicates
that any protection may be used.
The following describes these bitfields:
extraTraffic
Indicates that the LSP should use links that are
protecting other (primary) traffic. Such LSPs may
be preempted when the links carrying the (primary)
traffic being protected fail.
unprotected
Indicates that the LSP should not use any link layer
protection.
shared
Indicates that a shared link layer protection scheme,
such as 1:N protection, should be used to support the LSP.
dedicatedOneToOne
Indicates that a dedicated link layer protection scheme,
i.e., 1:1 protection, should be used to support the LSP.
dedicatedOnePlusOne
Indicates that a dedicated link layer protection scheme,
i.e., 1+1 protection, should be used to support the LSP.
enhanced
Indicates that a protection scheme that is more reliable than
Dedicated 1+1 should be used, e.g., 4 fiber BLSR/MS-SPRING.
This object is only meaningful if
gmplsTunnelLSPEncoding is not set to 0."
DEFVAL { { } }
::= { gmplsTunnelEntry 5 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 14]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
gmplsTunnelGPid OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the payload carried by the
LSP. It is only required when GMPLS will be used for
this LSP.
The values to use are currently defined in
Generalized Multi-Protocol Label Switching (GMPLS)
Signaling Functional Description, RFC 3471. Further
values may be defined in future RFCs.
unknown(0),
asynchE4(5),
asynchDS3T3(6),
asynchE3(7),
bitsynchE3(8),
bytesynchE3(9),
asynchDS2T2(10),
bitsynchDS2T2(11),
asynchE1(13),
bytesynchE1(14),
bytesynch31ByDS0(15),
asynchDS1T1(16),
bitsynchDS1T1(17),
bytesynchDS1T1(18),
VC11VC12(19),
ds1SFAsynch(22),
ds1ESFAsynch(23),
ds3M23Asynch(24),
ds3CBitParityAsynch(25),
vtLovc(26),
stsSpeHovc(27),
posNoScramble16BitCrc(28),
posNoScramble32BitCrc(29),
posScramble16BitCrc(30),
posScramble32BitCrc(31),
atm(32)
ethernet(33),
sdhSonet(34),
digitalwrapper(36),
lambda(37),
ansiEtsiPdh (38),
lapsSdh (40),
fddi (41),
dqdb (42),
fiberChannel3 (43),
hdlc (44),
ethernetV2DixOnly (45),
ethernet802dot3Only (46)
This object is only meaningful if
gmplsTunnelLSPEncoding is not set to 0."
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 15]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
REFERENCE
"1. Berger, L., et al., Generalized Multi-Protocol
Label Switching (GMPLS) Signaling Functional
Description, RFC 3471, January 2003."
DEFVAL { 0 }
::= { gmplsTunnelEntry 6 }
gmplsTunnelSecondary OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates that the requested LSP is a secondary LSP.
This object is only meaningful if
gmplsTunnelLSPEncoding is not set to 0."
DEFVAL { false }
::= { gmplsTunnelEntry 7 }
gmplsTunnelDirection OBJECT-TYPE
SYNTAX INTEGER {
forward (0),
bidirectional (1)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Whether this tunnel carries forward data (is
unidirectional) or is bidirectional.
Values of this object other than 'forward' are meaningful
only if gmplsTunnelLSPEncoding is not set to 0."
DEFVAL { forward }
::= { gmplsTunnelEntry 8 }
gmplsTunnelPathComp OBJECT-TYPE
SYNTAX INTEGER {
dynamicFull(1),-- CSPF fully computed
explicit(2),-- fully specified path
dynamicPartial(3) -- CSPF partially computed
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This value instructs the source node on how to perform
path computation on the explicit route specified by the
associated entries in the gmplsTunnelHopTable.
dynamicFull
The user specifies at least the source and
destination of the path and expects that the CSPF
will calculate the remainder of the path.
explicit
The user specifies the entire path for the tunnel to
take. This path may contain strict or loose hops.
Evaluation of the explicit route will be performed
hop by hop through the network.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 16]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
dynamicPartial
The user specifies at least the source and
destination of the path and expects that the CSPF
will calculate the remainder of the path. The path
computed by CSPF is allowed to be only partially
computed allowing the remainder of the path to be
filled in across the network.
This object deprecates gmplsTunnelHopEntryPathComp."
DEFVAL { dynamicFull }
::= { gmplsTunnelEntry 9 }
gmplsTunnelUpNotRecip OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the address of the upstream recipient for Notify
messages relating to this tunnel.
This object is only valid when signaling a tunnel using
RSVP. It is also not valid at the tail end of the tunnel.
If set to 0, no Notify Request object will be included in
outgoing Path messages."
DEFVAL { '00000000'H } -- 0.0.0.0
::= { gmplsTunnelEntry 10 }
gmplsTunnelDownNotRecip OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the address of the upstream recipient for Notify
messages relating to this tunnel.
This object is only valid when signaling a tunnel using
RSVP. It is also not valid at the head end of the tunnel.
If set to 0, no Notify Request object will be included in
outgoing Resv messages."
DEFVAL { '00000000'H } -- 0.0.0.0
::= { gmplsTunnelEntry 11 }
gmplsTunnelAdminStatusFlags OBJECT-TYPE
SYNTAX BITS {
delInProgress (0),
adminDown (1),
testing (2),
reflect (31)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Determines the setting of the Admin Status flags in the
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 17]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
Admin Status object or TLV, as described in
RFC 3471. Setting this field to a non-zero value will
result in the inclusion of the admin status object on
signaling messages.
This value of this object can be modified when the
corresponding mplsTunnelRowStatus and mplsTunnelAdminStatus
is active(1). By doing so, a new signaling message will be
triggered including the requested Admin Status object or
TLV."
::= { gmplsTunnelEntry 12 }
-- End of gmplsTunnelTable
-- Begin gmplsTunnelHopTable
gmplsTunnelHopTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsTunnelHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The gmplsTunnelHopTable 'extends' the
mplsTunnelHopTable. It is used to indicate the
explicit labels to be used in an explicit path for a
GMPLS tunnel defined in mplsTunnelTable and
gmplsTunnelTable, when it is established using
signaling. It does not insert new hops, but does
define new values for hops defined in
mplsTunnelHopTable.
Each row in this table is indexed by the same
indexes as mplsTunnelHopTable. It is acceptable for
some rows in mplsTunnelHopTable to have
corresponding entries in this table and some to have
no corresponding entry in this table.
The storage type for an entry in this table is
inherited from mplsTunnelHopStorageType in the
corresponding entry in mplsTunnelHopTable.
The row status of an entry in this table is
controlled by mplsTunnelHopRowStatus in the
corresponding entry in mplsTunnelHopTable. That is,
it is not permitted to create a row in this table,
nor to modify an existing row, when the
corresponding mplsTunnelHopRowStatus has value
active(1)."
::= { gmplsTeObjects 2 }
gmplsTunnelHopEntry OBJECT-TYPE
SYNTAX GmplsTunnelHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents additions to a
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 18]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
tunnel hop defined in mplsTunnelHopEntry. At an
ingress to a tunnel an entry in this table is
created by a network administrator for an ERLSP to
be set up by a signaling protocol. At transit and
egress nodes an entry in this table may be used to
represent the explicit path instructions received
using the signaling protocol."
INDEX {
mplsTunnelHopListIndex,
mplsTunnelHopPathOptionIndex,
mplsTunnelHopIndex
}
::= { gmplsTunnelHopTable 1 }
GmplsTunnelHopEntry ::= SEQUENCE {
gmplsTunnelHopLabelStatuses BITS,
gmplsTunnelHopExplicitLabel Unsigned32,
gmplsTunnelHopExpRvrsLabel Unsigned32
}
gmplsTunnelHopLabelStatuses OBJECT-TYPE
SYNTAX BITS {
forwardPresent (0),
reversePresent (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This bitmask indicates the presence of labels
indicated by the gmplsTunnelHopExplicitLabel and
gmplsTunnelHopExpRvrsLabel objects.
For the Present bits, a set bit indicates that a
label is present for this hop in the route. This
allows zero to be a valid label value."
::= { gmplsTunnelHopEntry 1 }
gmplsTunnelHopExplicitLabel OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the row entry in the gmplsLabelTable that
defines the explicit label to use in the explicit
route as the forward path label at this point. This
value only has meaning if the forwardPresent bit of
gmplsTunnelHopLabelStatuses is set.
Note that the other indexes in the gmplsLabelTable
should be interpreted as follows:
- The gmplsLabelInterface should be zero because
this label is not tied to any specific interface
on this LSR
- The gmplsLabelSubindex is used to represent label
concatenations. The first (or only) component
label SHOULD have gmplsLabelSubindex set to zero.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 19]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
This variable is only valid for settings of
mplsTunnelHopAddrType which may be associated with a
forward path label.
Note that in implementations where the label may be
encoded within a 32 bit integer and where
gmplsLabelTable is not implemented, this object may
directly contain the label value to use."
::= { gmplsTunnelHopEntry 2 }
gmplsTunnelHopExpRvrsLabel OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the row entry in the gmplsLabelTable that
defines the explicit label to use in the explicit
route as the reverse path label at this point. This
value only has meaning if the reversePresent bit of
gmplsTunnelHopLabelStatuses is set.
The same rules and notes apply as set out for
gmplsTunnelHopExplicitLabel."
::= { gmplsTunnelHopEntry 3 }
-- End of gmplsTunnelHopTable
-- Tunnel Actual Route Hop table.
gmplsTunnelARHopTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsTunnelARHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The gmplsTunnelARHopTable 'extends' the
mplsTunnelARHopTable. It is used to indicate the
labels currently in use for a GMPLS tunnel defined
in mplsTunnelTable and gmplsTunnelTable, as reported
by the signaling protocol. It does not insert new
hops, but does define new values for hops defined in
mplsTunnelARHopTable.
Each row in this table is indexed by the same indexes as
mplsTunnelARHopTable. It is acceptable for some rows in
mplsTunnelARHopTable to have corresponding entries in this
table and some to have no corresponding entry in this table.
Note that since the information necessary to build
entries within this table is not provided by some
signaling protocols and might not be returned in all
cases of other signaling protocols, implementation
of this table and mplsTunnelARHopTable is optional.
Furthermore, since the information in this table is
actually provided by the signaling protocol after
the path has been set-up, the entries in this table
are provided only for observation, and hence, all
variables in this table are accessible exclusively
as read-only."
::= { gmplsTeObjects 3 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 20]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
gmplsTunnelARHopEntry OBJECT-TYPE
SYNTAX GmplsTunnelARHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents additions to a
tunnel hop visible in mplsTunnelARHopEntry. An entry
is created by the signaling protocol for a signaled
ERLSP set up by the signaling protocol.
At any node on the LSP (ingress, transit or egress)
Thus at this table and mplsTunnelARHopTable (if the
tables are supported and if the signaling protocol
is recording actual route information) contains the
actual route of the whole tunnel. If the signaling
protocol is not recording the actual route, this
table MAY report the information from the
gmplsTunnelHopTable or the gmplsTunnelCHopTable.
Note that the recording of actual labels is distinct
from the recording of the actual route in some
signaling protocols. This feature is enabled using
the gmplsTunnelAttributes object."
INDEX {
mplsTunnelARHopListIndex,
mplsTunnelARHopIndex
}
::= { gmplsTunnelARHopTable 1 }
GmplsTunnelARHopEntry ::= SEQUENCE {
gmplsTunnelARHopLabelStatuses BITS,
gmplsTunnelARHopExplicitLabel Unsigned32,
gmplsTunnelARHopExpRvrsLabel Unsigned32,
gmplsTunnelARHopProtection BITS
}
gmplsTunnelARHopLabelStatuses OBJECT-TYPE
SYNTAX BITS {
forwardPresent (0),
reversePresent (1),
forwardGlobal (2),
reverseGlobal (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This bitmask indicates the presence and status of
labels indicated by the
gmplsTunnelARHopExplicitLabel and
gmplsTunnelARHopExpRvrsLabel objects.
For the Present bits, a set bit indicates that a label
is present for this hop in the route. For the Global bits,
a set bit indicates that the label comes from the Global
Label Space. A clear bit indicates that this is a Per-
Interface label. A Global bit only has meaning if the
corresponding Present bit is set."
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 21]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
::= { gmplsTunnelARHopEntry 1 }
gmplsTunnelARHopExplicitLabel OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the row entry in the gmplsLabelTable that
defines the label in use as the forward path label
on the path at this point.
This value only has meaning if the forwardPresent
bit of gmplsTunnelARHopLabelStatuses is set.
Note that the other indexes in the gmplsLabelTable
should be interpreted as follows:
- The gmplsLabelInterface should be zero because
this label is not tied to any specific interface
on this LSR
- The gmplsLabelSubindex is used to represent label
concatenations. The first (or only) component
label SHOULD have gmplsLabelSubindex set to zero.
This variable is only valid for settings of
mplsTunnelARHopAddrType which may be associated with
a forward path label.
Note that in implementations where the label may be
encoded within a 32 bit integer and where
gmplsLabelTable is not implemented, this object may
directly contain the label value to use."
::= { gmplsTunnelARHopEntry 2 }
gmplsTunnelARHopExpRvrsLabel OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the row entry in the gmplsLabelTable that
defines the label used in the path as reverse path
at this point.
This value only has meaning if the reversePresent
bit of gmplsTunnelARHopLabelStatuses is set.
The same rules and notes apply as set out for
gmplsTunnelARHopExplicitLabel."
::= { gmplsTunnelARHopEntry 3 }
gmplsTunnelARHopProtection OBJECT-TYPE
SYNTAX BITS {
localAvailable (0),
localInUse (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Availability and usage of protection on the reported link.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 22]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
localAvailable
Indicates that the link downstream of this node
is protected via a local repair mechanism.
localInUse
Indicates that a local repair mechanism is in
use to maintain this tunnel (usually in the
face of an outage of the link it was previously
routed over)."
::= { gmplsTunnelARHopEntry 4 }
-- End of mplsTunnelARHopTable
-- Tunnel Computed Hop table.
gmplsTunnelCHopTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsTunnelCHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The gmplsTunnelCHopTable 'extends' the
mplsTunnelCHopTable. It is used to indicate
additional information about the hops of a GMPLS
tunnel defined in mplsTunnelTable and
gmplsTunnelTable, as computed by a constraint-based
routing protocol, based on the mplsTunnelHopTable
and the gmplsTunnelHopTable.
Each row in this table is indexed by the same indexes as
mplsTunnelCHopTable. It is acceptable for some rows in
mplsTunnelCHopTable to have corresponding entries in this
table and some to have no corresponding entry in this table.
Please note that since the information necessary to
build entries within this table may not be supported
by some LSRs, implementation of this table is optional.
Furthermore, since the information in this table is actually
provided by a path computation component after the path has
been computed, the entries in this table are provided only
for observation, and hence, all objects in this table are
accessible exclusively as read-only."
::= { gmplsTeObjects 4 }
gmplsTunnelCHopEntry OBJECT-TYPE
SYNTAX GmplsTunnelCHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents additions to a
computed tunnel hop visible in mplsTunnelCHopEntry.
An entry is created by a path computation component
based on the hops specified in the corresponding
mplsTunnelHopTable and gmplsTunnelHopTable.
At a transit LSR this table (if the table is
supported) MAY contain the path computed by path
computation engine on (or on behalf of) the transit LSR."
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 23]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
INDEX {
mplsTunnelCHopListIndex,
mplsTunnelCHopIndex
}
::= { gmplsTunnelCHopTable 1 }
GmplsTunnelCHopEntry ::= SEQUENCE {
gmplsTunnelCHopLabelStatuses BITS,
gmplsTunnelCHopExplicitLabel Unsigned32,
gmplsTunnelCHopExpRvrsLabel Unsigned32
}
gmplsTunnelCHopLabelStatuses OBJECT-TYPE
SYNTAX BITS {
forwardPresent (0),
reversePresent (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This bitmask indicates the presence indicated by the
gmplsTunnelCHopExplicitLabel and
gmplsTunnelCHopExpRvrsLabel objects.
A set bit indicates that a label is present for this
hop in the route thus allowing zero to be a valid
label value."
::= { gmplsTunnelCHopEntry 1 }
gmplsTunnelCHopExplicitLabel OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the row entry in the gmplsLabelTable that
defines the label to use as the forward path label
on the path at this point.
This value only has meaning if the forwardPresent
bit of gmplsTunnelCHopLabelStatuses is set.
Note that the other indexes in the gmplsLabelTable
should be interpreted as follows:
- The gmplsLabelInterface should be zero because
this label is not tied to any specific interface
on this LSR
- The gmplsLabelSubindex is used to represent label
concatenations. The first (or only) component
label SHOULD have gmplsLabelSubindex set to zero.
This variable is only valid for settings of
mplsTunnelCHopAddrType which may be associated with
a forward path label.
Note that in implementations where the label may be
encoded within a 32 bit integer and where
gmplsLabelTable is not implemented, this object may
directly contain the label value to use."
::= { gmplsTunnelCHopEntry 2 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 24]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
gmplsTunnelCHopExpRvrsLabel OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the row entry in the gmplsLabelTable that
defines the label to use in the path as reverse path
at this point.
This value only has meaning if the reversePresent
bit of gmplsTunnelCHopLabelStatuses is set.
The same rules and notes apply as set out for
gmplsTunnelCHopExplicitLabel."
::= { gmplsTunnelCHopEntry 3 }
-- End of gmplsTunnelCHopTable
-- GMPLS Tunnel Reverse Direction Performance Table.
gmplsTunnelReversePerfTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsTunnelReversePerfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table 'augments' the gmplsTunnelTable to provides
per-tunnel packet performance information for the
reverse direction of a bidirectional tunnel. It can be
seen as supplementing the mplsTunnelPerfTable which
augments the mplsTunnelTable."
::= { gmplsTeObjects 5 }
gmplsTunnelReversePerfEntry OBJECT-TYPE
SYNTAX GmplsTunnelReversePerfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by the LSR for
every bidirectional GMPLS tunnel where packets are
visible to the LSR."
AUGMENTS { gmplsTunnelEntry }
::= { gmplsTunnelReversePerfTable 1 }
GmplsTunnelReversePerfEntry ::= SEQUENCE {
gmplsTunnelReversePerfPackets Counter32,
gmplsTunnelReversePerfHCPackets Counter64,
gmplsTunnelReversePerfErrors Counter32,
gmplsTunnelReversePerfBytes Counter32,
gmplsTunnelReversePerfHCBytes Counter64
}
gmplsTunnelReversePerfPackets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets forwarded on the tunnel in the
reverse direction if it is bidirectional."
::= { gmplsTunnelReversePerfEntry 1 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 25]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
gmplsTunnelReversePerfHCPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High capacity counter for number of packets
forwarded on the tunnel in the reverse direction if
it is bidirectional."
::= { gmplsTunnelReversePerfEntry 2 }
gmplsTunnelReversePerfErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of errored packets received on the tunnel in
the reverse direction if it is bidirectional."
::= { gmplsTunnelReversePerfEntry 3 }
gmplsTunnelReversePerfBytes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of bytes forwarded on the tunnel in the
reverse direction if it is bidirectional."
::= { gmplsTunnelReversePerfEntry 4 }
gmplsTunnelReversePerfHCBytes OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High capacity counter for number of bytes forwarded
on the tunnel in the reverse direction if it is
bidirectional."
::= { gmplsTunnelReversePerfEntry 5 }
-- End of gmplsTunnelReversePerfTable
-- GMPLS Tunnel Error Table.
gmplsTunnelErrorTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsTunnelErrorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table 'augments' the mplsTunnelTable
This table provides per-tunnel information about
errors. Errors may be detected locally or reported
through the signaling protocol.
Error reporting is not exclusive to GMPLS and this
table may be applied in MPLS systems."
::= { gmplsTeObjects 6 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 26]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
gmplsTunnelErrorEntry OBJECT-TYPE
SYNTAX GmplsTunnelErrorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by the LSR for
every tunnel where error information is visible to
the LSR.
Note that systems which read the objects in this table
one at a time may experience a discontinuity as the
result of a new error occurring in between object reads.
Systems that are vulnerable to this should read
gmplsTunnelErrorLastTime before and after reading the
other objects."
AUGMENTS { mplsTunnelEntry }
::= { gmplsTunnelErrorTable 1 }
GmplsTunnelErrorEntry ::= SEQUENCE {
gmplsTunnelErrorLastErrorType INTEGER,
gmplsTunnelErrorLastTime TimeStamp,
gmplsTunnelErrorReporterType INTEGER,
gmplsTunnelErrorReporterIpv4Addr InetAddressIPv4,
gmplsTunnelErrorReporterIpv6Addr InetAddressIPv6,
gmplsTunnelErrorCode Unsigned32,
gmplsTunnelErrorSubcode Unsigned32,
gmplsTunnelErrorHelpString DisplayString
}
gmplsTunnelErrorLastErrorType OBJECT-TYPE
SYNTAX INTEGER {
noError (0),
unknown (1),
localProtocol (2),
remoteProtocol (3),
configuration (4),
pathComputation (5),
localResources (6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The nature of the last error. Provides
interpretation context for
gmplsTunnelErrorProtocolCode and
gmplsTunnelErrorProtocolSubcode. A value of noError
(0) shows that there is no error associated with
this tunnel and means that the other objects in this
entry have no meaning."
::= { gmplsTunnelErrorEntry 1 }
gmplsTunnelErrorLastTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time at which the last error occurred. This is
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 27]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
presented as the value of SysUpTime when the error
occurred or was reported to this node.
If gmplsTunnelErrorLastErrorType has the value
noError (0), then this object is ignored."
::= { gmplsTunnelErrorEntry 2 }
gmplsTunnelErrorReporterType OBJECT-TYPE
SYNTAX INTEGER {
unknown (0),
localNode (1),
localIpV4 (2),
remoteIpV4 (3),
localIpV6 (4),
remoteIpV6 (5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The reporter of the last error recorded.
This object is used principally to aid in
interpretation of gmplsTunnelErrorReporterIpv4Addr
and gmplsTunnelErrorReporterIpv6Addr. Where the
error has been locally generated and there is no
requirement to associate the error with any specific
local address (such as an interface), the value
localNode (2) may be used.
If gmplsTunnelErrorLastError has the value noError
(0), then this object is ignored."
::= { gmplsTunnelErrorEntry 3 }
gmplsTunnelErrorReporterIpv4Addr OBJECT-TYPE
SYNTAX InetAddressIPv4
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address of the node reporting the last error, or
the address of the resource (such as an interface)
associated with the error.
If gmplsTunnelErrorLastErrorType has the value
noError (0), then this object is ignored.
This object only has meaning if the object
gmplsTunnelErrorReporterType has value localIpV4 (2)
or remoteIpV4 (3). Otherwise the object should
contain the value zero and should be ignored."
::= { gmplsTunnelErrorEntry 4 }
gmplsTunnelErrorReporterIpv6Addr OBJECT-TYPE
SYNTAX InetAddressIPv6
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address of the node reporting the last error, or
the address of the resource (such as an interface)
associated with the error.
If gmplsTunnelErrorLastErrorType has the value
noError (0), then this object is ignored.
This object only has meaning if the object
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 28]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
gmplsTunnelErrorReporterType has value localIpV6 (4)
or remoteIpV4 (5). Otherwise the object should
contain the value zero and should be ignored."
::= { gmplsTunnelErrorEntry 5 }
gmplsTunnelErrorCode OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The primary error code associated with the last
error.
The interpretation of this error code depends on the
value of gmplsTunnelErrorLastErrorType. If the value
of gmplsTunnelErrorLastErrorType is noError (0) the
value of this object should be 0 and should be
ignored. If the value of
gmplsTunnelErrorLastErrorType is localProtocol (2)
or remoteProtocol (3) the error should be
interpreted in the context of the signling protocol
identified by the mplsTunnelSignallingProto object.
Values in excess 32767 of are not used by signaling
protocols and may safely be used as implementation-
specific error codes. "
::= { gmplsTunnelErrorEntry 6 }
gmplsTunnelErrorSubcode OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The secondary error code associated with the last
error and the protocol used to signal this tunnel.
This value is interprettd in the context of the
value of gmplsTunnelErrorCode.
If the value of gmplsTunnelErrorLastErrorType is
noError (0) the value of this object should be 0 and
should be ignored."
::= { gmplsTunnelErrorEntry 7 }
gmplsTunnelErrorHelpString OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A textual string containing information about the
last error, recovery actions and support advice. If
there is no help string this object contains a zero
length string.
If the value of gmplsTunnelErrorLastErrorType is
noError (0) this object should contain a zero length
string, but may contain a help string indicating
that there is no error."
::= { gmplsTunnelErrorEntry 8 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 29]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
-- Module compliance.
gmplsTeGroups
OBJECT IDENTIFIER ::= { gmplsTeConformance 1 }
gmplsTeCompliances
OBJECT IDENTIFIER ::= { gmplsTeConformance 2 }
gmplsTeModuleCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance statement for agents that support the
GMPLS TE MIB."
MODULE -- this module
-- The mandatory group has to be implemented by all
-- LSRs that originate/terminate ESLSPs/tunnels.
-- In addition, depending on the type of tunnels
-- supported, other groups become mandatory as
-- explained below.
MANDATORY-GROUPS {
gmplsTunnelGroup,
gmplsTunnelScalarGroup
}
-- GROUP gmplsTunnelManualGroup
-- DESCRIPTION
-- "This group is mandatory for devices which support
-- manual configuration of tunnels, in addition to
-- gmplsTunnelGroup. The following constraints apply:
-- mplsTunnelSignallingProto should be at least read-
-- only with a value of none(1)."
GROUP gmplsTunnelSignaledGroup
DESCRIPTION
"This group is mandatory for devices which support
signaled tunnel set up, in addition to
gmplsTunnelGroup. The following constraints apply:
mplsTunnelSignallingProto should be at least read-
only returning a value of ldp(2), or rsvp(3)."
GROUP gmplsTunnelIsNotIntfcGroup
DESCRIPTION
"This group is mandatory for devices which support
tunnels that are not interfaces, in addition to
gmplsTunnelGroup. The following constraints apply:
gmplsTunnelIsIf must at least be read-only returning
no(0)."
GROUP gmplsTunnelIsIntfcGroup
DESCRIPTION
"This group is mandatory for devices which support
tunnels that are interfaces, in addition to
gmplsTunnelGroup."
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 30]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
GROUP gmplsTunnelOptionalGroup
DESCRIPTION
"Objects in this group are optional."
-- GMPLS Tunnel scalars.
-- All scalars have max access read-only
-- gmplsTunnelTable
OBJECT gmplsTunnelAttributes
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsTunnelLSPEncoding
SYNTAX Integer32
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsTunnelSwitchingType
SYNTAX Integer32
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsTunnelLinkProtection
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsTunnelGPid
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsTunnelSecondary
SYNTAX TruthValue
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsTunnelDirection
SYNTAX INTEGER {
forward (0),
bidirectional (1)
}
MIN-ACCESS read-only
DESCRIPTION
"Only forward (0) is required."
OBJECT gmplsTunnelPathComp
SYNTAX INTEGER {
dynamicFull(1), -- CSPF fully computed
explicit(2), -- fully
dynamicPartial(3) -- CSPF partially computed
}
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 31]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
MIN-ACCESS read-only
DESCRIPTION
"Only explicit (2) is required."
OBJECT gmplsTunnelUpNotRecip
SYNTAX IpAddress
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsTunnelDownNotRecip
SYNTAX IpAddress
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsTunnelAdminStatusFlags
SYNTAX BITS {
delInProgress (0),
adminDown (1),
testing (2),
reflect (31)
}
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
-- gmplsTunnelHopTable
-- gmplsTunnelHopLabelStatuses has max access read-only
OBJECT gmplsTunnelHopExplicitLabel
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsTunnelHopExpRvrsLabel
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
-- gmplsTunnelARHopTable
-- all objects have max access read-only
-- glmpsTunnelCHopTable
-- all objects have max access read-only
-- gmplsTunnelReversePerfTable
-- all objects have max access read-only
-- gmplsTunnelErrorTable
-- all objects have max access read-only
::= { gmplsTeCompliances 1 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 32]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
-- Units of conformance.
gmplsTunnelGroup OBJECT-GROUP
OBJECTS {
gmplsTunnelDirection,
gmplsTunnelReversePerfPackets,
gmplsTunnelReversePerfHCPackets,
gmplsTunnelReversePerfErrors,
gmplsTunnelReversePerfBytes,
gmplsTunnelReversePerfHCBytes,
gmplsTunnelErrorLastErrorType,
gmplsTunnelErrorLastTime,
gmplsTunnelErrorReporterType,
gmplsTunnelErrorReporterIpv4Addr,
gmplsTunnelErrorReporterIpv6Addr,
gmplsTunnelErrorCode,
gmplsTunnelErrorSubcode,
gmplsTunnelErrorHelpString
}
STATUS current
DESCRIPTION
"Necessary, but not sufficient, set of objects to implement
tunnels. In addition, depending on the type of the tunnels
supported (for example, manually configured or signaled,
persistent or non-persistent, etc.), the following other
groups defined below are mandatory: gmplsTunnelManualGroup
and/or gmplsTunnelSignaledGroup, gmplsTunnelIsNotIntfcGroup
and/or gmplsTunnelIsIntfcGroup."
::= { gmplsTeGroups 1 }
-- gmplsTunnelManualGroup OBJECT-GROUP
-- OBJECTS {
-- mplsTunnelSignallingProto
-- }
-- STATUS current
-- DESCRIPTION
-- "Object(s) needed to implement manually configured
-- tunnels."
-- ::= { gmplsTeGroups 2 }
gmplsTunnelSignaledGroup OBJECT-GROUP
OBJECTS {
gmplsTunnelAttributes,
gmplsTunnelLSPEncoding,
gmplsTunnelSwitchingType,
gmplsTunnelLinkProtection,
gmplsTunnelGPid,
gmplsTunnelSecondary,
gmplsTunnelPathComp,
gmplsTunnelUpNotRecip,
gmplsTunnelDownNotRecip,
gmplsTunnelAdminStatusFlags,
gmplsTunnelHopLabelStatuses,
gmplsTunnelHopExplicitLabel,
gmplsTunnelHopExpRvrsLabel
}
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 33]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
STATUS current
DESCRIPTION
"Objects needed to implement signaled tunnels."
::= { gmplsTeGroups 3 }
gmplsTunnelScalarGroup OBJECT-GROUP
OBJECTS {
gmplsTunnelsConfigured,
gmplsTunnelsActive
}
STATUS current
DESCRIPTION
"Scalar objects needed to implement MPLS tunnels."
::= { gmplsTeGroups 4 }
gmplsTunnelIsIntfcGroup OBJECT-GROUP
OBJECTS {
gmplsTunnelUnnumIf
}
STATUS current
DESCRIPTION
"Objects needed to implement tunnels that are
interfaces."
::= { gmplsTeGroups 5 }
gmplsTunnelIsNotIntfcGroup OBJECT-GROUP
OBJECTS {
gmplsTunnelUnnumIf
}
STATUS current
DESCRIPTION
"Objects needed to implement tunnels that are not
interfaces."
::= { gmplsTeGroups 6 }
gmplsTunnelOptionalGroup OBJECT-GROUP
OBJECTS {
gmplsTunnelARHopLabelStatuses,
gmplsTunnelARHopExplicitLabel,
gmplsTunnelARHopExpRvrsLabel,
gmplsTunnelARHopProtection,
gmplsTunnelCHopLabelStatuses,
gmplsTunnelCHopExplicitLabel,
gmplsTunnelCHopExpRvrsLabel
}
STATUS current
DESCRIPTION
"The objects in this group are optional."
::= { gmplsTeGroups 7 }
END
9. Security Considerations
It is clear that the MIB modules described in this document in
association with the MPLS-TE-STD-MIB are potentially useful for
monitoring of MPLS and GMPLS tunnels. These MIB modules can also be
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 34]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
used for configuration of certain objects, and anything that can be
configured can be incorrectly configured, with potentially disastrous
results.
There are a number of management objects defined in these MIB modules
with a MAX-ACCESS clause of read-write and/or read-create. Such
objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
network operations. These are the tables and objects and their
sensitivity/vulnerability:
o the gmplsTunnelTable and gmplsTunnelHopTable collectively contain
objects to provision GMPLS tunnels interfaces at their ingress
LSRs. Unauthorized write access to objects in these tables, could
result in disruption of traffic on the network. This is especially
true if a tunnel has already been established. The use of stronger
mechanisms such as SNMPv3 security should be considered where
possible. Specifically, SNMPv3 VACM and USM MUST be used with any
SNMPv3 agent which implements these MIB modules.
Some of the readable objects in these MIB modules "i.e., objects with
a MAX-ACCESS other than not-accessible" may be considered sensitive
or vulnerable in some network environments. It is thus important to
control even GET and/or NOTIFY access to these objects and possibly
to even encrypt the values of these objects when sending them over
the network via SNMP. These are the tables and objects and their
sensitivity/vulnerability:
o the gmplsTunnelTable, gmplsTunnelHopTable, gmplsTunnelARHopTable,
gmplsTunnelCHopTable, gmplsTunnelReversePerfTable,
gmplsTunnelErrorTable collectively show the tunnel network
topology and status. If an Administrator does not want to reveal
this information, then these tables should be considered
sensitive/vulnerable.
SNMP versions prior to SNMPv3 did not include adequate security. Even
if the network itself is secure "for example by using IPSec", even
then, there is no control as to who on the secure network is allowed
to access and GET/SET "read/change/create/delete" the objects in
these MIB modules. It is RECOMMENDED that implementers consider the
security features as provided by the SNMPv3 framework "see [RFC3410],
section 8", including full support for the SNMPv3 cryptographic
mechanisms "for authentication and privacy".
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module, is properly configured to give access to
the objects only to those principals "users" that have legitimate
rights to indeed GET or SET "change/create/delete" them.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 35]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
10. Acknowledgments
This draft extends [TEMIB]. The authors would like to express their
gratitude to all those who worked on that earlier MIB document.
Thanks also to Tony Zinicola and Jeremy Crossen for their valuable
contributions during an early implementation, and to Baktha
Muralidharan for his review.
Special thanks to Joan Cucchiara and Len Nieman for their help with
compilation issues.
11. References
11.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J.,
Case, J., Rose, M., and S. Waldbusser, "Structure
of Management Information Version 2 (SMIv2)", STD
58, RFC 2578, April 1999.
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J.,
Case, J., Rose, M., and S. Waldbusser, "Textual
Conventions for SMIv2", STD 58, RFC 2579, April
1999.
[RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J.,
Case, J., Rose, M., and S. Waldbusser, "Conformance
Statements for SMIv2", STD 58, RFC 2580, April
1999.
[RFC3031] Rosen, E., Viswanathan, A., and R. Callon,
"Multiprotocol Label Switching Architecture", RFC
3031, January 2001.
[RFC3209] Awduche, D., Berger, L., Gan, D., Li, T.,
Srinivasan, V., and G. Swallow, "RSVP-TE:
Extensions to RSVP for LSP Tunnels", RFC 3209,
December 2001.
[RFC3212] Jamoussi, B., Aboul-Magd, O., Andersson, L.,
Ashwood-Smith, P., Hellstrand, F., Sundell, K.,
Callon, R., Dantu, R., Wu, L., Doolan, P., Worster,
T., Feldman, N., Fredette, A., Girish, M., Gray,
E., Halpern, J., Heinanen, J., Kilty, T., Malis,
A., and P. Vaananen, "Constraint-Based LSP Setup
using LDP", RFC 3212, December 2001."
[RFC3471] Berger, L. (Editor), "Generalized Multi-Protocol
Label Switching (GMPLS) Signaling Functional
Description", RFC 3471, January 2003.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 36]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
[RFC3472] Ashwood-Smith, P., Berger, L. (Editors),
"Generalized MPLS Signaling - CR-LDP Extensions",
RFC 3472, January 2003.
[RFC3473] Berger, L. (Editor), "Generalized MPLS Signaling -
RSVP-TE Extensions", RFC 3473, January 2003.
[RFC3477] Kompella, K. and Rekhter, Y., "Signalling Unnumbered
Links in RSVP-TE", RFC 3477, January 2003.
[RFC3480] Kompella, K., Rekhter, Y. and Kullberg, A.,
"Signalling Unnumbered Links in CR-LDP", RFC 3480,
February 2003.
[GMPLSArch] Mannie, E. (Editor), "Generalized Multiprotocol
Label Switching (GMPLS) Architecture", Internet
Draft <draft-many-gmpls-architecture-07.txt>, May
2003, work in progress.
[GMPLSLSRMIB] Nadeau, T., Srinivasan, C., A., Farrel, A., Hall,
T., and Harrison, E., "Generalized Multiprotocol
Label Switching (GMPLS) Label Switching Router
(LSR) Management Information Base", draft-ietf-
ccamp-gmpls-lsr-mib-03.txt, November 2003, work in
progress.
[GMPLSOSPF] Kompella, K., et al., "OSPF Extensions in Support
of Generalized MPLS", draft-ietf-ccamp-ospf-gmpls-
extensions-11.txt, October 2002, work in progress.
[GMPLSTCMIB] Nadeau, T., Srinivasan, C., Farrel, A., Hall, T.,
and Harrison, E., "Definitions of Textual
Conventions for Multiprotocol Label Switching
(MPLS) Management", draft-ietf-ccamp-gmpls-te-mib-
03.txt, November 2003, work in progress.
[LSRMIB] Srinivasan, C., Viswanathan, A. and T. Nadeau,
"Multiprotocol Label Switching (MPLS) Label
Switching Router (LSR) Management Information
Base", Internet Draft <draft-ietf-mpls-lsr-mib-
12.txt>, August 2003, work in progress.
[TCMIB] Nadeau, T., Cucchiara, J. (Editors) "Definitions of
Textual Conventions for Multiprotocol Label
Switching (MPLS) Management", Internet Draft
<draft-ietf-mpls-tc-mib-09.txt>, August 2003, work
in progress.
[TEMIB] Nadeau, T., Srinivasan, C, Viswanathan, A.,
"Multiprotocol Label Switching (MPLS) Traffic
Engineering Management Information Base", Internet
Draft <draft-ietf-mpls-te-mib-12.txt>, August 2003,
work in progress.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 37]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
11.2. Informational References
[RFC2026] S. Bradner, "The Internet Standards Process --
Revision 3", RFC 2026, October 1996.
[RFC3413] Levi, D., Meyer, P., Stewart, B., "SNMP
Applications", RFC 3413, December 2002.
[RFC3410] Case, J., Mundy, R., Partain, D. and B. Stewart,
"Introduction and Applicability Statements for
Internet-Standard Management Framework", RFC 3410,
December 2002.
[RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An
Architecture for Describing Simple Network
Management Protocol (SNMP) Management Frameworks",
RFC 3411, December 2002.
12. Authors' Addresses
Thomas D. Nadeau
Cisco Systems, Inc.
300 Apollo Drive
Chelmsford, MA 01824
Phone: +1-978-244-3051
Email: tnadeau@cisco.com
Cheenu Srinivasan
Bloomberg L.P.
499 Park Ave.,
New York, NY 10022
Phone: +1-212-893-3682
Email: cheenu@bloomberg.net
Adrian Farrel
Old Dog Consulting
Phone: +44-(0)-1978-860944
Email: adrian@olddog.co.uk
Tim Hall
Data Connection Ltd.
100 Church Street
Enfield, Middlesex
EN2 6BQ, UK
Phone: +44 20 8366 1177
Email: timhall@dataconnection.com
Ed Harrison
Data Connection Ltd.
100 Church Street
Enfield, Middlesex
EN2 6BQ, UK
Phone: +44 20 8366 1177
Email: ed.harrison@dataconnection.com
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 38]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
13. Full Copyright Statement
Copyright (C) The Internet Society (2003). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns. This
document and the information contained herein is provided on an "AS
IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK
FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL
NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE.
14. Intellectual Property Notice
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11 [RFC2028].
Copies of claims of rights made available for publication and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use
of such proprietary rights by implementers or users of this
specification can be obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive
Director.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 39]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-03.txt November 2003
15. Changes and Pending Work
This section to be removed before the draft progresses to RFC.
15.1. Pending Work
The following work items have been identified for this draft. They
will be addressed in a future version.
- Expand conformance statements to give one for monitoring only,
and one for monitoring and control.
- Consider a way to expose tunnel head, tunnel tail, and tunnel
transit entries through distinct indexing or tables.
- Provide support for configuring tunnel resources in GMPLS
systems. For example, SONET/SDH or G.709. This might be done
through an arbitrary RowPointer to an external MIB.
- Crankback request and reported information.
- Add support for IF_ID control and error reporting.
- Add LSR or interface config for Hellos and restart options.
- Update enumerated types in line with latest GMPLS drafts. Examine
how these can be managed by IANA.
- Resolve ownership of enumerated types that are also defined in
GMPLS or routing drafts. These could be owned by IANA, imported
from another MIB, or manually kept in step here. If they are not
maintained externally then they are likely to diverge and MIB
implementations will need to provide mappings.
- Update MIB description in section 5.
15.2. Changes from version 2 to version 3
- Work on basic compilation issues.
- Resolve defaults for objects with syntax BITS.
- Update references.
- Clarify which objects can be modified when rowStatus and
adminStatus are set to active.
- Control and reporting of upstream and downstream Notify
Recipients.
- Add support for control and reporting of GMPLS Administrative
Status object.
- Update examples.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 40]
Network Working Group Thomas D. Nadeau
Internet Draft Cisco Systems, Inc.
Expires: May 2004
Cheenu Srinivasan
Bloomberg L.P.
Adrian Farrel
Old Dog Consulting
Tim Hall
Ed Harrison
Data Connection Ltd.
November 2003
Generalized Multiprotocol Label Switching (GMPLS)
Label Switching Router (LSR) Management Information Base
draft-ietf-ccamp-gmpls-lsr-mib-03.txt
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC 2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other documents
at any time. It is inappropriate to use Internet-Drafts as
reference material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects to configure and/or
monitor a Generalized Multiprotocol Label Switching (GMPLS) Label
Switching Router (LSRs).
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 1]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
Table of Contents
1. Introduction 2
1.1. Migration Strategy 2
2. Terminology 3
3. The SNMP Management Framework 3
4. Outline 3
4.1. Summary of the GMPLS LSR MIB Module 4
5. Bidirectional LSPs 4
6. Example of LSP Setup 5
7. GMPLS Label Switching Router MIB Definitions 6
8. GMPLS Label MIB Definitions 14
9. Security Considerations 25
10. Acknowledgments 26
11. IANA Considerations 27
11.1. IANA Considerations for GMPLS-LSR-STD-MIB 27
11.2. IANA Considerations FOR GMPLS-LABEL-STD-MIB 27
12. References 27
12.1. Normative References 27
12.2. Informational References 28
13. Authors' Addresses 29
14. Full Copyright Statement 30
15. Intellectual Property Notice 30
16. Changes and Pending Work 31
16.1. Pending Work 31
1. Introduction
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects for modeling a
Generalized Multiprotocol Label Switching (GMPLS) [GMPLSArch] Label
Switching Router (LSR).
Comments should be made directly to the CCAMP mailing list at
ccamp@ops.ietf.org.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119, reference
[RFC2119].
1.1. Migration Strategy
This MIB module extends the Label Switching Router MIB module defined
for use with MPLS [LSRMIB]. The only changes made are additions for
support of GMPLS or changes that are necessary to support the
increased complexity of a GMPLS system.
The companion document modeling and managing GMPLS based traffic
engineering [GMPLSTEMIB] extends the MPLS TE MIB module [TEMIB] with
the same intentions.
Textual conventions and OBJECT-IDENTIFIERS are defined in
[GMPLSTCMIB] which extends the set of textual conventions originally
defined in [TCMIB].
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 2]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
2. Terminology
This document uses terminology from the document describing the MPLS
architecture [RFC3031] and the GMPLS architecture [GMPLSArch].
A label switched path (LSP) is modeled as a connection consisting of
one or more incoming segments (in-segments) and/or one or more
outgoing segments (out-segments) at an LSR. The association or
interconnection of the in-segments and out-segments is accomplished
by using a cross-connect. We use the terminology "connection" and
"LSP" interchangeably where the meaning is clear from the context.
in-segment This is analogous to a GMPLS label on an interface.
out-segment This is analogous to a GMPLS label on an interface.
cross-connect This describes the conceptual connection between a
set of in-segments and out-segments.
Note that either set may be 0; that is, a cross-
connect may connect only out-segments together with
no in-segments in the case where an LSP is
originating on an LSR.
3. The SNMP Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a
MIB module that is compliant to the SMIv2, which is described in STD
58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC
2580 [RFC2580].
4. Outline
Configuring statically provisioned GMPLS LSPs through an LSR involves
the following steps:
- Configuring an interface using the MPLS LSR MIB module.
- Enabling GMPLS on GMPLS capable interfaces using this MIB module.
- Configuring in-segments and out-segments using the MPLS LSR MIB
module.
- Configuring GMPLS extensions to the in-segments and out-segments
using this MIB module.
- Setting up the cross-connect table in the MPLS LSR MIB module to
associate segments and/or to indicate connection origination and
termination.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 3]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
- Optionally setting up labels in the label table in this MIB module
if the textual convention
MplsLabel is not capable of holding the required label (for
example, if the label requires more than 32 bits to encode it), or
if the operator wishes to disambiguate GMPLS label types.
- Optionally specifying label stack actions in the MPLS LSR MIB
module.
- Optionally specifying segment traffic parameters in the MPLS LSR
MIB module.
4.1. Summary of the GMPLS LSR MIB Module
The MIB tables in this MIB module are as follows.
- The interface configuration table (gmplsInterfaceTable), which
extends mplsInterfaceTable to enable the GMPLS protocol on MPLS-
capable interfaces.
- The in-segment (gmplsInSegmentTable) and out-segment
(gmplsOutSegmentTable) tables extend mplsInSegmentTable and
mplsOutSegmentTable to configuring GMPLS-specific parameters for
LSP segments at an LSR.
- The gmplsLabelTable extends mplsLabelTable and allows Generalized
Labels to be defined and managed in a central location.
Generalized Labels can be of variable length and have distinct
bit-by-bit interpretations according to the use that is made of
them.
These tables are described in the subsequent sections.
5. Bidirectional LSPs
This MIB supports bidirectional LSPs as required for GMPLS.
A single value of mplsXCIndex is shared by all of the segments for
the entire bidirectional LSP. This facilitates a simple reference
from [TEMIB] and [GMPLSTEMIB], and makes fate-sharing more obvious.
It is, however, important that the direction of segments is
understood to avoid connecting all in-segments to all out-segments.
This is achieved by an object in each segment that indicates the
direction of the segment with respect to data flow.
A segment that is marked as 'forward' carries data from the 'head' of
the LSP to the 'tail'. A segment marked as 'reverse' carries data in
the reverse direction.
Where an LSP is signaled using a conventional signaling protocol, the
'head' of the LSP is the source of the signaling (also known as the
ingress) and the 'tail' is the destination (also known as the
egress). For manually configured LSPs an arbitrary decision must be
made about which segments are 'forward' and which 'reverse'. For
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 4]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
consistency this decision should be made across all LSRs that
participate in the LSP by assigning 'head' and 'tail' ends to the
LSP.
6. Example of LSP Setup
In this section we provide a brief example of using the MIB objects
described in section 9 to set up an LSP. While this example is not
meant to illustrate every nuance of the MIB, it is intended as an aid
to understanding some of the key concepts. It is meant to be read
after going through the MIB itself. A prerequisite is an
understanding of [LSRMIB].
Suppose that one would like to manually create a best-effort, bi-
directional LSP. Assume that, in the forward direction, the LSP
enters the LSR via MPLS interface A with ifIndex 12 and exits the LSR
via MPLS interface B with ifIndex 13. For the reverse direction, we
assume the LSP enters via interface B and leaves via interface A
(i.e. the forward and reverse directions use the same bi-directional
interfaces). Let us also assume that we do not wish to have a label
stack beneath the top label on the outgoing labeled packets. The
following example illustrates which rows and corresponding objects
might be created to accomplish this.
We must first create rows in the gmplsLabelTable corresponding to the
labels required for each of the forward and reverse direction in- and out-
segments. For the purpose of this example the forward and reverse labels
on each interface will be the same, hence we need to create just two
rows in the gmplsLabelTable - one for each interface.
In gmplsLabelTable:
{
gmplsLabelInterface = 12,
gmplsLabelIndex = 1,
gmplsLabelSubindex = 1,
gmplsLabelType = gmplsFreeformGeneralizedLabel(3),
gmplsLabelMplsLabel = 0,
gmplsLabelPortWavelength = 0,
gmplsLabelFreeformLength = 8,
gmplsLabelFreeform = 0x123456789ABCDEF0
gmplsLabelSonetSdhSignalIndex = 0,
gmplsLabelSdhVc = 0,
gmplsLabelSdhVcBranch = 0,
gmplsLabelSonetSdhBranch = 0,
gmplsLabelSonetSdhGroupBranch = 0,
gmplsLabelWavebandId = 0,
gmplsLabelWavebandStartLabel = 0,
gmplsLabelWavebandEndLabel = 0,
gmplsLabelRowStatus = createAndGo(4),
gmplsLabelStorageType = 0
}
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 5]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
In gmplsLabelTable:
{
gmplsLabelInterface = 13,
gmplsLabelIndex = 1,
gmplsLabelSubindex = 1,
gmplsLabelType = gmplsFreeformGeneralizedLabel(3),
gmplsLabelMplsLabel = 0,
gmplsLabelPortWavelength = 0,
gmplsLabelFreeformLength = 8,
gmplsLabelFreeform = 0xFEDCBA9876543210
gmplsLabelSonetSdhSignalIndex = 0,
gmplsLabelSdhVc = 0,
gmplsLabelSdhVcBranch = 0,
gmplsLabelSonetSdhBranch = 0,
gmplsLabelSonetSdhGroupBranch = 0,
gmplsLabelWavebandId = 0,
gmplsLabelWavebandStartLabel = 0,
gmplsLabelWavebandEndLabel = 0,
gmplsLabelRowStatus = createAndGo(4),
gmplsLabelStorageType = 0
}
We must next create the appropriate in-segment and out-segment entries.
These are done in [LSRMIB] using the mplsInSegmentTable and
mplsOutSegmentTable. Note that we use a row pointer to the two rows in the
gmplsLableTable rather than specifying the labels explicitly in the
in- and out-segment tables. Also note that the row status for each row
is set to createAndWait(5) to allow corresponding entries in the
gmplsInSegmentTable and gmplsOutSegmentTable to be created.
For the forward direction.
In mplsInSegmentTable:
{
mplsInSegmentIndex = 0x00000015
mplsInSegmentLabel = 0, -- incoming label in label table
mplsInSegmentNPop = 1,
mplsInSegmentInterface = 12, -- incoming interface
-- RowPointer MUST point to the first accesible column.
mplsInSegmentLabelPtr = gmplsLabelInterface.1,
mplsInSegmentTrafficParamPtr = 0.0,
mplsInSegmentRowStatus = createAndWait(5)
}
In mplsOutSegmentTable:
{
mplsOutSegmentIndex = 0x00000012,
mplsOutSegmentInterface = 13, -- outgoing interface
mplsOutSegmentPushTopLabel = true(1),
mplsOutSegmentTopLabel = 0, -- outgoing label in label table
-- RowPointer MUST point to the first accesible column.
mplsOutSegmentTrafficParamPtr = 0.0,
mplsOutSegmentLabelPtr = gmplsLabelInterface.2,
mplsOutSegmentRowStatus = createAndWait(5)
}
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 6]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
For the reverse direction.
In mplsInSegmentTable:
{
mplsInSegmentIndex = 0x00000016
mplsInSegmentLabel = 0, -- incoming label in label table
mplsInSegmentNPop = 1,
mplsInSegmentInterface = 13, -- incoming interface
-- RowPointer MUST point to the first accesible column.
mplsInSegmentLabelPtr = gmplsLabelInterface.2,
mplsInSegmentTrafficParamPtr = 0.0,
mplsInSegmentRowStatus = createAndWait(5)
}
In mplsOutSegmentTable:
{
mplsOutSegmentIndex = 0x00000013,
mplsOutSegmentInterface = 12, -- outgoing interface
mplsOutSegmentPushTopLabel = true(1),
mplsOutSegmentTopLabel = 0, -- outgoing label in label table
-- RowPointer MUST point to the first accesible column.
mplsOutSegmentTrafficParamPtr = 0.0,
mplsOutSegmentLabelPtr = gmplsLabelInterface.1,
mplsOutSegmentRowStatus = createAndWait(5)
}
These table entries are extended by entries in gmplsInSegmentTable
and gmplsOutSegmentTable. Note that the nature of the 'extends'
relationship is that the entry in gmplsInSegmentTable has the same
index values as the entry in mplsInSegmentTable. Similarly, the entry
in gmplsOutSegmentTable has the same index values as the entry in
mplsOutSegmentTable.
First for the forward direction:
In gmplsInSegmentTable(0x00000015)
{
gmplsInSegmentDirection = forward (1)
}
In gmplsOutSegmentTable(0x00000012)
{
gmplsOutSegmentDirection = forward (1),
gmplsOutSegmentTTLDecrement = 1
}
Next for the reverse direction:
In gmplsInSegmentTable(0x00000016)
{
gmplsInSegmentDirection = reverse (2)
}
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 7]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
In gmplsOutSegmentTable(0x00000013)
{
gmplsOutSegmentDirection = reverse (2),
gmplsOutSegmentTTLDecrement = 1
}
Next, two cross-connect entries are created in the mplsXCTable of the
MPLS LSR MIB, thereby associating the newly created segments
together.
In mplsXCTable:
{
mplsXCIndex = 0x01,
mplsXCInSegmentIndex = 0x00000015,
mplsXCOutSegmentIndex = 0x00000012,
mplsXCLspId = 0x0102 -- unique ID
mplsXCLabelStackIndex = 0x00, -- only a single
-- outgoing label
mplsXCRowStatus = createAndGo(4)
}
In mplsXCTable:
{
mplsXCIndex = 0x02,
mplsXCInSegmentIndex = 0x00000016,
mplsXCOutSegmentIndex = 0x00000013,
mplsXCLspId = 0x0102 -- unique ID
mplsXCLabelStackIndex = 0x00, -- only a single
-- outgoing label
mplsXCRowStatus = createAndGo(4)
}
Finally, the in-segments and out-segments are activated.
In mplsInSegmentTable(0x00000015):
{
mplsInSegmentRowStatus = active(1)
}
In mplsInSegmentTable(0x00000016):
{
mplsInSegmentRowStatus = active(1)
}
In mplsOutSegmentTable(0x00000012):
{
mplsOutSegmentRowStatus = active(1)
}
In mplsOutSegmentTable(0x00000013):
{
mplsOutSegmentRowStatus = active(1)
}
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 8]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
7. GMPLS Label Switching Router MIB Definitions
GMPLS-LSR-STD-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Unsigned32
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
GmplsSegmentDirection, gmplsStdMIB
FROM GMPLS-TC-STD-MIB
mplsInterfaceIndex, mplsInSegmentIndex, mplsOutSegmentIndex
FROM MPLS-LSR-STD-MIB
;
gmplsLsrStdMIB MODULE-IDENTITY
LAST-UPDATED
"200310300900Z" -- 30 October 2003 9:00:00 GMT"
ORGANIZATION
"Common Control And Management Protocols (CCAMP)
Working Group"
CONTACT-INFO
" Thomas D. Nadeau
Cisco Systems, Inc.
Email: tnadeau@cisco.com
Cheenu Srinivasan
Bloomberg L.P.
Email: cheenu@bloomberg.net
Adrian Farrel
Old Dog Consulting
Email: adrian@olddog.co.uk
Ed Harrison
Data Connection Ltd.
Email: ed.harrison@dataconnection.com
Tim Hall
Data Connection Ltd.
Email: timhall@dataconnection.com
Comments about this document should be emailed direct to the
CCAMP working group mailing list at ccamp@ops.ietf.org"
DESCRIPTION
"This MIB module contains managed object definitions
for the Generalized Multiprotocol Label Switching
(GMPLS) Router as defined in: Ashwood-Smith et al.,
Generalized Multiprotocol Label Switching (GMPLS)
Architecture, Internet Draft <draft-many-gmpls-
architecture-01.txt>, March 2001, work in progress.
Copyright (C) The Internet Society (2003). This
version of this MIB module is part of RFCXXX; see
the RFC itself for full legal notices."
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 9]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
-- Revision history.
REVISION
"200310300900Z" -- 30 October 2003 09:00:00 GMT
DESCRIPTION
"Initial revision, published as part of RFC XXXX."
::= { gmplsStdMIB xx }
-- Top level components of this MIB module.
-- Notifications
-- no notifications are currently defined.
gmplsLsrNotifications OBJECT IDENTIFIER ::= { gmplsLsrStdMIB 0 }
-- Tables, Scalars
gmplsLsrObjects OBJECT IDENTIFIER ::= { gmplsLsrStdMIB 1 }
-- Conformance
gmplsLsrConformance OBJECT IDENTIFIER ::= { gmplsLsrStdMIB 2 }
-- GMPLS Interface Table.
gmplsInterfaceTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsInterfaceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies per-interface GMPLS capability
and associated information. It extends the
information in mplsInterfaceTable."
::= { gmplsLsrObjects 1 }
gmplsInterfaceEntry OBJECT-TYPE
SYNTAX GmplsInterfaceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in this table is created
automatically by an LSR for every interface capable
of supporting GMPLS and which is configured to do
so. A conceptual row in this table will exist if and
only if a corresponding entry in mplsInterfaceTable
exists, and a corresponding entry in ifTable exists
with ifType = mpls(166). If the associated entry in
ifTable is operationally disabled (thus removing the
GMPLS capabilities on the interface) or the entry in
mplsInterfaceTable is deleted, the corresponding
entry in this table MUST be deleted shortly
thereafter.
The indexing is the same as that for mplsInterfaceTable.
Thus, the entry with index 0 represents the per-platform
label space and contains parameters that apply to all
interfaces that participate in the per-platform label space."
INDEX { mplsInterfaceIndex }
::= { gmplsInterfaceTable 1 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 10]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
GmplsInterfaceEntry ::= SEQUENCE {
gmplsInterfaceSignalingCaps BITS
}
gmplsInterfaceSignalingCaps OBJECT-TYPE
SYNTAX BITS {
unknown (0),
rsvpGmpls (1),
crldpGmpls (2), -- note the use of CR-LDP is deprecated
otherGmpls (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Defines the signaling capabilities on this
interface. Multiple bits may legitimately be set at
once. Setting no bits implies that GMPLS signaling
cannot be performed on this interface and all LSPs
must be manually provisioned."
::= { gmplsInterfaceEntry 1 }
-- End of gmplsInterfaceTable
-- In-segment table.
gmplsInSegmentTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsInSegmentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table extends the mplsInSegmentTable to provide
GMPLS-specific information about incoming segments
to an LSR."
::= { gmplsLsrObjects 2 }
gmplsInSegmentEntry OBJECT-TYPE
SYNTAX GmplsInSegmentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table extends the representation of
an incoming segment represented by an entry in
mplsInSegmentTable. An entry can be created by a
network administrator or an SNMP agent, or a GMPLS
signaling protocol.
Note that the storage type for this entry SHOULD be
inherited from the corresponding entry in the
mplsInSegmentTable given by the value of the
mplsInSegmentStorageType object."
INDEX { mplsInSegmentIndex }
::= { gmplsInSegmentTable 1 }
GmplsInSegmentEntry ::= SEQUENCE {
gmplsInSegmentDirection GmplsSegmentDirection
}
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 11]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
gmplsInSegmentDirection OBJECT-TYPE
SYNTAX GmplsSegmentDirection
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the direction of data flow on
this segment. This object cannot be modified if
mplsInSegmentRowStatus for the associated entry in
the mplsInSegmentTable is active(1)."
DEFVAL { forward }
::= { gmplsInSegmentEntry 1 }
-- End of gmplsInSegmentTable
-- Out-segment table.
gmplsOutSegmentTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsOutSegmentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table extends the mplsOutSegmentTable to
provide GMPLS-specific information about outgoing
segments from an LSR."
::= { gmplsLsrObjects 3 }
gmplsOutSegmentEntry OBJECT-TYPE
SYNTAX GmplsOutSegmentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table extends the representation of
an outgoing segment represented by an entry in
mplsOutSegmentTable. An entry can be created by a
network administrator or an SNMP agent, or a GMPLS
signaling protocol.
Note that the storage type for this entry SHOULD be
inherited from the corresponding entry in the
mplsOutSegmentTable given by the value of the
mplsOutSegmentStorageType object."
INDEX { mplsOutSegmentIndex }
::= { gmplsOutSegmentTable 1 }
GmplsOutSegmentEntry ::= SEQUENCE {
gmplsOutSegmentDirection GmplsSegmentDirection,
gmplsOutSegmentTTLDecrement Unsigned32
}
gmplsOutSegmentDirection OBJECT-TYPE
SYNTAX GmplsSegmentDirection
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the direction of data flow on
this segment. This object cannot be modified if
mplsOutSegmentRowStatus for the associated entry in
the mplsOutSegmentTable is active(1)."
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 12]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
DEFVAL { forward }
::= { gmplsOutSegmentEntry 1 }
gmplsOutSegmentTTLDecrement OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the amount by which to
decrement the TTL of any payload packets forwarded
on this segment if per-hop decrementing is being
done.
A value of zero indicates that no decrement should
be made or that per-hop decrementing is not in
force.
See the gmplsTunnelTTLDecrement object in the
gmplsTunnelTable of [GMPLSTEMIB] for a value by
which to decrement the TTL for the whole of a
tunnel.
This object cannot be modified if
mplsOutSegmentRowStatus for the associated entry in
the mplsOutSegmentTable is active(1)."
DEFVAL { 0 }
::= { gmplsOutSegmentEntry 2 }
-- End of gmplsOutSegmentTable
-- Module compliance.
gmplsLsrGroups
OBJECT IDENTIFIER ::= { gmplsLsrConformance 1 }
gmplsLsrCompliances
OBJECT IDENTIFIER ::= { gmplsLsrConformance 2 }
-- Compliance requirement for fully compliant implementations.
gmplsLsrModuleFullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance statement for agents that provide full
support for GMPLS-LSR-STD-MIB."
MODULE IF-MIB -- The Interfaces Group MIB, RFC 2863.
MANDATORY-GROUPS {
ifGeneralInformationGroup,
ifCounterDiscontinuityGroup
}
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 13]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
MODULE MPLS-LSR-STD-MIB -- The MPLS LSR MIB
MANDATORY-GROUPS {
mplsInterfaceGroup,
mplsInSegmentGroup,
mplsOutSegmentGroup,
mplsXCGroup,
mplsPerfGroup,
mplsLsrNotificationGroup
}
MODULE -- this module
MANDATORY-GROUPS {
gmplsInterfaceGroup,
gmplsInSegmentGroup,
gmplsOutSegmentGroup
}
-- gmplsInSegmentTable
OBJECT gmplsInSegmentDirection
SYNTAX GmplsSegmentDirection
MIN-ACCESS read-write
DESCRIPTION
"Only forward(1) needs to be supported by
implementations that only support unidirectional
LSPs."
-- gmplsOutSegmentTable
OBJECT gmplsOutSegmentDirection
SYNTAX GmplsSegmentDirection
MIN-ACCESS read-write
DESCRIPTION
"Only forward(1) needs to be supported by
implementations that only support unidirectional
LSPs."
OBJECT gmplsOutSegmentTTLDecrement
SYNTAX Unsigned32 (0..255)
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { gmplsLsrCompliances 1 }
-- Compliance requirement for implementations that provide read-only
-- access.
gmplsLsrModuleReadOnlyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance requirement for implementations that only
provide read-only support for GMPLS-LSR-STD-MIB. Such
devices can then be monitored but cannot be configured
using this MIB modules."
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 14]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
MODULE IF-MIB -- The interfaces Group MIB, RFC 2863
MANDATORY-GROUPS {
ifGeneralInformationGroup,
ifCounterDiscontinuityGroup
}
MODULE MPLS-LSR-STD-MIB
MANDATORY-GROUPS {
mplsInterfaceGroup,
mplsInSegmentGroup,
mplsOutSegmentGroup,
mplsXCGroup,
mplsPerfGroup
}
MODULE -- this module
MANDATORY-GROUPS {
gmplsInterfaceGroup,
gmplsInSegmentGroup,
gmplsOutSegmentGroup
}
-- gmplsInterfaceGroup
OBJECT gmplsInterfaceSignalingCaps
SYNTAX BITS {
unknown (0),
rsvpGmpls (1),
crldpGmpls (2),
otherGmpls (3)
}
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
-- gmplsInSegmentTable
OBJECT gmplsInSegmentDirection
SYNTAX GmplsSegmentDirection
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. Only forward(1) needs
to be supported by implementations that only support
unidirectional LSPs."
-- gmplsOutSegmentTable
OBJECT gmplsOutSegmentDirection
SYNTAX GmplsSegmentDirection
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. Only forward(1) needs
to be supported by implementations that only support
unidirectional LSPs."
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 15]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
OBJECT gmplsOutSegmentTTLDecrement
SYNTAX Unsigned32 (0..255)
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { gmplsLsrCompliances 2 }
-- Units of conformance.
gmplsInterfaceGroup OBJECT-GROUP
OBJECTS {
gmplsInterfaceSignalingCaps
}
STATUS current
DESCRIPTION
"Collection of objects needed for GMPLS interface
configuration and performance information."
::= { gmplsLsrGroups 1 }
gmplsInSegmentGroup OBJECT-GROUP
OBJECTS {
gmplsInSegmentDirection
}
STATUS current
DESCRIPTION
"Collection of objects needed to implement a GMPLS
in-segment."
::= { gmplsLsrGroups 2 }
gmplsOutSegmentGroup OBJECT-GROUP
OBJECTS {
gmplsOutSegmentDirection,
gmplsOutSegmentTTLDecrement
}
STATUS current
DESCRIPTION
"Collection of objects needed to implement a GMPLS
out-segment."
::= { gmplsLsrGroups 3 }
END
8. GMPLS Label MIB Definitions
GMPLS-LABEL-STD-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Unsigned32,
Integer32
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
RowStatus, StorageType
FROM SNMPv2-TC
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 16]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
InterfaceIndexOrZero
FROM IF-MIB
IndexIntegerNextFree
FROM DIFFSERV-MIB
MplsLabel
FROM MPLS-TC-STD-MIB
GmplsGeneralizedLabelTypes, GmplsFreeformLabel,
gmplsStdMIB
FROM GMPLS-TC-STD-MIB
;
gmplsLabelStdMIB MODULE-IDENTITY
LAST-UPDATED
"200310300900Z" -- 30 October 2003 9:00:00 GMT"
ORGANIZATION
"Common Control And Management Protocols (CCAMP)
Working Group"
CONTACT-INFO
" Thomas D. Nadeau
Cisco Systems, Inc.
Email: tnadeau@cisco.com
Cheenu Srinivasan
Bloomberg L.P.
Email: cheenu@bloomberg.net
Adrian Farrel
Old Dog Consulting
Email: adrian@olddog.co.uk
Ed Harrison
Data Connection Ltd.
Email: ed.harrison@dataconnection.com
Tim Hall
Data Connection Ltd.
Email: timhall@dataconnection.com
Comments about this document should be emailed direct to the
CCAMP working group mailing list at ccamp@ops.ietf.org"
DESCRIPTION
"This MIB module contains managed object definitions
for labels within GMPLS systems."
-- Revision history.
REVISION
"200310300900Z" -- 30 October 2003 09:00:00 GMT
DESCRIPTION
"Initial revision, published as part of RFC XXXX."
::= { gmplsStdMIB xx }
-- Top level components of this MIB module.
-- Notifications
-- no notifications are currently defined.
gmplsLabelNotifications OBJECT IDENTIFIER ::= { gmplsLabelStdMIB 0 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 17]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
-- Tables, Scalars
gmplsLabelObjects OBJECT IDENTIFIER ::= { gmplsLabelStdMIB 1 }
-- Conformance
gmplsLabelConformance OBJECT IDENTIFIER ::= { gmplsLabelStdMIB 2 }
-- GMPLS Label Table.
gmplsLabelIndexNext OBJECT-TYPE
SYNTAX IndexIntegerNextFree
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains an unused value for
gmplsLabelIndex, or a zero to indicate
that no unused value exists or is available.
An management application wishing to create
a row in the gmplsLabelTable may read this
object and then attempt to create a row in
the table. If row creation fails (because
another application has already created a row
with the supplied index) the management
application should read this object again
to get a new index value.
When a row is created in the gmplsLabelTable
with the gmplsLabelIndex value held by this
object, an implementation MUST change the value
in this object.
"
::= { gmplsLabelObjects 1 }
gmplsLabelTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsLabelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of GMPLS Labels. This table allows the
representation of the more complex label forms
required for GMPLS which cannot be held within the
textual convention MplsLabel. That is labels that
cannot be encoded within 32 bits. It is,
nevertheless also capable of holding 32 bit labels
or regular MPLS labels if desired.
Each entry in this table represents an individual
GMPLS label value. Labels in the tables in other
MIBs are referred to using row pointer into this
table. The indexing of this table provides for
arbitrary indexing and also for concatenation of
labels."
::= { gmplsLabelObjects 2 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 18]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
gmplsLabelEntry OBJECT-TYPE
SYNTAX GmplsLabelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents a single label
value. There are three indexes into the table.
- The interface index may be helpful to distinguish
which labels are in use on which interfaces or to
handle cases where there are a very large number
of labels in use in the system. When label
representation is desired to apply to the whole
system or when it is not important to distinguish
labels by their interfaces, this index MAY be set
to zero.
- The label index provides a way of identifying the
label.
- The label sub-index is only used for concatenated
labels. It identifies each component label. When
non-concatenated labels are used, this index
SHOULD be set to zero.
A storage type object is supplied to control the
storage type for each entry, but implementations
should note that the storage type of conceptual rows
in other tables that include row pointers to an
entry in this table SHOULD dictate the storage type
of the rows in this table where the row in the other
table is more persistent."
INDEX {
gmplsLabelInterface,
gmplsLabelIndex,
gmplsLabelSubindex }
::= { gmplsLabelTable 1 }
GmplsLabelEntry ::= SEQUENCE {
gmplsLabelInterface InterfaceIndexOrZero,
gmplsLabelIndex Unsigned32,
gmplsLabelSubindex Unsigned32,
gmplsLabelType GmplsGeneralizedLabelTypes,
gmplsLabelMplsLabel MplsLabel,
gmplsLabelPortWavelength Unsigned32,
gmplsLabelFreeformLength Integer32,
gmplsLabelFreeform GmplsFreeformLabel,
gmplsLabelSonetSdhSignalIndex Integer32,
gmplsLabelSdhVc Integer32,
gmplsLabelSdhVcBranch Integer32,
gmplsLabelSonetSdhBranch Integer32,
gmplsLabelSonetSdhGroupBranch Integer32,
gmplsLabelWavebandId Unsigned32,
gmplsLabelWavebandStart Unsigned32,
gmplsLabelWavebandEnd Unsigned32,
gmplsLabelRowStatus RowStatus,
gmplsLabelStorageType StorageType
}
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 19]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
gmplsLabelInterface OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interface on which this label is used. If the
label has or could have applicability across the
whole system, this object SHOULD be set to zero."
::= { gmplsLabelEntry 1 }
gmplsLabelIndex OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary index into the table to identify a
label.
Note that implementations that are representing 32
bit labels within this table MAY choose to align
this index with the value of the label, but should
be aware of the implications of sparsely populated
tables.
A management application may read the gmplsLabelIndexNext
object to find a suitable value for this object."
::= { gmplsLabelEntry 2 }
gmplsLabelSubindex OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"In conjunction with gmplsLabelInterface and
gmplsLabelIndex, this object uniquely identifies
this row. This sub-index allows a single GMPLS label
to be defined as a concatenation of labels. This is
particularly useful in TDM.
The ordering of sub-labels is strict with the sub-
label with lowest gmplsLabelSubindex appearing
first. Note that all sub-labels of a single GMPLS
label must share the same gmplsLabelInterface and
gmplsLabelIndex values. For labels that are not
composed of concatenated sub-labels, this value
SHOULD be set to zero."
::= { gmplsLabelEntry 3 }
gmplsLabelType OBJECT-TYPE
SYNTAX GmplsGeneralizedLabelTypes
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Identifies the type of this label. Note that this
object does not determine whether MPLS or GMPLS
signaling is in use: a value of gmplsMplsLabel (1)
denotes that a 23 bit MPLS packet label is present,
but does not describe whether this is signaled using
MPLS or GMPLS.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 20]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
The value of this object helps determine which of
the following objects are valid.
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
::= { gmplsLabelEntry 4 }
gmplsLabelMplsLabel OBJECT-TYPE
SYNTAX MplsLabel
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of an MPLS label (that is a packet label)
if this table is used to store it. This may be used
in MPLS systems even though the label values can be
adequately stored in the MPLS MIB modules. Further,
in mixed MPLS and GMPLS systems it may be
advantageous to store all labels in a single label
table. Lastly, in GMPLS systems where packet labels
are used (that is in systems that use GMPLS
signaling and GMPLS labels for packet switching) it
may be desirable to use this table.
This object is only valid if gmplsLabelType is set
to gmplsMplsLabel (1).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
::= { gmplsLabelEntry 6 }
gmplsLabelPortWavelength OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of a Port or Wavelength Label when carried
as a Generalized Label. Only valid if gmplsLabelType
is set to gmplsPortWavelengthLabel(2).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
::= { gmplsLabelEntry 7 }
gmplsLabelFreeformLength OBJECT-TYPE
SYNTAX Integer32 (1..64)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The length of a freeform Generalized Label indicated
in the gmplsFreeformLabel object. Only valid if
gmplsLabelType is set to
gmplsFreeformGeneralizedLabel(3).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
::= { gmplsLabelEntry 8 }
gmplsLabelFreeform OBJECT-TYPE
SYNTAX GmplsFreeformLabel
MAX-ACCESS read-create
STATUS current
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 21]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
DESCRIPTION
"The value of a freeform Generalized Label that does
not conform to one of the standardized label
encoding or that an implementation chooses to
represent as an octet string without further
decoding. The length of this object is given by the
value of gmplsFreeformLength. Only valid if
gmplsLabelType is set to
gmplsFreeformGeneralizedLabel(3).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
::= { gmplsLabelEntry 9 }
gmplsLabelSonetSdhSignalIndex OBJECT-TYPE
SYNTAX Integer32 (0..4095)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Signal Index value (S) of a SONET or SDH
Generalized Label. Zero indicates that this field is
not significant. Only valid if gmplsLabelType is set
to gmplsSonetLabel(4) or gmplsSdhLabel(5).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
::= { gmplsLabelEntry 10 }
gmplsLabelSdhVc OBJECT-TYPE
SYNTAX Integer32 (0..15)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The VC Indicator (U) of an SDH Generalized Label.
Zero indicates that this field is non-significant.
Only valid if gmplsLabelType is set to
gmplsSdhLabel(5).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
::= { gmplsLabelEntry 11 }
gmplsLabelSdhVcBranch OBJECT-TYPE
SYNTAX Integer32 (0..15)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The VC Branch Indicator (K) of an SDH Generalized
Label. Zero indicates that this field is non-
significant. Only valid if gmplsLabelType is set to
gmplsSdhLabel(5).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
::= { gmplsLabelEntry 12 }
gmplsLabelSonetSdhBranch OBJECT-TYPE
SYNTAX Integer32 (0..15)
MAX-ACCESS read-create
STATUS current
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 22]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
DESCRIPTION
"The Branch Indicator (L) of a SONET or SDH
Generalized Label. Zero indicates that this field is
non-significant. Only valid gmplsLabelType is set to
gmplsSonetLabel(4) or gmplsSdhLabel(5).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
::= { gmplsLabelEntry 13 }
gmplsLabelSonetSdhGroupBranch OBJECT-TYPE
SYNTAX Integer32 (0..15)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Group Branch Indicator (M) of a SONET or SDH
Generalized Label. Zero indicates that this field is
non-significant. Only valid if gmplsLabelType is set
to gmplsSonetLabel(4) or gmplsSdhLabel(5).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
::= { gmplsLabelEntry 14 }
gmplsLabelWavebandId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The waveband identifier component of a waveband
label. Only valid if gmplsLabelType is set to
gmplsWavebandLabel(6).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
::= { gmplsLabelEntry 15 }
gmplsLabelWavebandStart OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The starting label component of a waveband label.
Only valid if gmplsLabelType is set to
gmplsWavebandLabel(6).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
::= { gmplsLabelEntry 16 }
gmplsLabelWavebandEnd OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The end label component of a waveband label. Only
valid if gmplsLabelType is set to
gmplsWavebandLabel(6).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
::= { gmplsLabelEntry 17 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 23]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
gmplsLabelRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable is used to create, modify, and/or
delete a row in this table. When a row in this
table has a row in the active(1) state, no
objects in this row can be modified except the
gmplsLabelRowStatus and gmplsLabelStorageType."
::= { gmplsLabelEntry 18 }
gmplsLabelStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable indicates the storage type for this
object.
The agent MUST ensure that this object's value
remains consistent with the storage type of any rows
in other tables that contain pointers to this row.
In particular, the storage type of this row must be
at least as permanent as that of any row that point
to it.
Conceptual rows having the value 'permanent' need
not allow write-access to any columnar objects in
the row."
REFERENCE
"See RFC2579."
DEFVAL { volatile }
::= { gmplsLabelEntry 19 }
-- End of GMPLS Label Table
-- Module compliance.
gmplsLabelGroups
OBJECT IDENTIFIER ::= { gmplsLabelConformance 1 }
gmplsLabelCompliances
OBJECT IDENTIFIER ::= { gmplsLabelConformance 2 }
gmplsLabelModuleFullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance statement for agents that support
the GMPLS Label MIB module."
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 24]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
MODULE -- this module
-- The mandatory groups have to be implemented by
-- LSRs claiming support for this MIB module. This MIB module is,
-- however, not mandatory for a working implementation of a GMPLS
-- LSR with full MIB support if the GMPLS labels in use can be
-- represented within a 32 bit quantity.
MANDATORY-GROUPS {
gmplsLabelTableGroup
}
-- Units of conformance.
GROUP gmplsLabelTableGroup
DESCRIPTION
"This group is mandatory for devices which support
the gmplsLabelTable."
GROUP gmplsLabelPacketGroup
DESCRIPTION
"This group extends gmplsLabelTableGroup for
implementations that support packet labels."
GROUP gmplsLabelPortWavelengthGroup
DESCRIPTION
"This group extends gmplsLabelTableGroup for
implementations that support port and wavelength
labels."
GROUP gmplsLabelFreeformGroup
DESCRIPTION
"This group extends gmplsLabelTableGroup for
implementations that support freeform labels."
GROUP gmplsLabelSonetSdhGroup
DESCRIPTION
"This group extends gmplsLabelTableGroup for
implementations that support SONET or SDH labels."
GROUP gmplsLabelWavebandGroup
DESCRIPTION
"This group extends gmplsLabelTableGroup for
implementations that support Waveband labels."
-- gmplsLabelTable
OBJECT gmplsLabelType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelMplsLabel
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 25]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
OBJECT gmplsLabelPortWavelength
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelFreeformLength
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelFreeform
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelSonetSdhSignalIndex
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelSdhVc
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelSdhVcBranch
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelSonetSdhBranch
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelSonetSdhGroupBranch
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelWavebandId
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelWavebandStart
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelWavebandEnd
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 26]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
OBJECT gmplsLabelRowStatus
SYNTAX RowStatus {
active(1),
notInService(2)
}
WRITE-SYNTAX RowStatus {
active(1),
notInService(2),
createAndGo(4),
destroy(6)
}
DESCRIPTION
"Support for notInService, createAndWait and notReady
is not required."
OBJECT gmplsLabelStorageType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { gmplsLabelCompliances 1 }
-- Units of conformance.
gmplsLabelTableGroup OBJECT-GROUP
OBJECTS {
gmplsLabelIndexNext,
gmplsLabelType,
gmplsLabelRowStatus,
gmplsLabelStorageType
}
STATUS current
DESCRIPTION
"Necessary, but not sufficient, set of objects to
implement label table support. In addition,
depending on the type of labels supported (for
example, wavelength labels), the following other
groups defined below are mandatory:
gmplsLabelPacketGroup and/or
gmplsLabelPortWavelengthGroup and/or
gmplsLabelFreeformGroup and/or
gmplsLabelSonetSdhGroup."
::= { gmplsLabelGroups 1 }
gmplsLabelPacketGroup OBJECT-GROUP
OBJECTS {
gmplsLabelMplsLabel
}
STATUS current
DESCRIPTION
"Object needed to implement Packet (MPLS) labels."
::= { gmplsLabelGroups 2 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 27]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
gmplsLabelPortWavelengthGroup OBJECT-GROUP
OBJECTS {
gmplsLabelPortWavelength
}
STATUS current
DESCRIPTION
"Object needed to implement Port and Wavelength
labels."
::= { gmplsLabelGroups 3 }
gmplsLabelFreeformGroup OBJECT-GROUP
OBJECTS {
gmplsLabelFreeformLength,
gmplsLabelFreeform
}
STATUS current
DESCRIPTION
"Object needed to implement Freeform labels."
::= { gmplsLabelGroups 4 }
gmplsLabelSonetSdhGroup OBJECT-GROUP
OBJECTS {
gmplsLabelSonetSdhSignalIndex,
gmplsLabelSdhVc,
gmplsLabelSdhVcBranch,
gmplsLabelSonetSdhBranch,
gmplsLabelSonetSdhGroupBranch
}
STATUS current
DESCRIPTION
"Object needed to implement SONET and SDH labels."
::= { gmplsLabelGroups 5 }
gmplsLabelWavebandGroup OBJECT-GROUP
OBJECTS {
gmplsLabelWavebandId,
gmplsLabelWavebandStart,
gmplsLabelWavebandEnd
}
STATUS current
DESCRIPTION
"Object needed to implement Waveband labels."
::= { gmplsLabelGroups 6 }
END
9. Security Considerations
It is clear that the MIB modules described in this document in
association with the MPLS-LSR-STD-MIB are potentially useful for
monitoring of GMPLS LSRs. These MIB modules can also be used for
configuration of certain objects, and anything that can be configured
can be incorrectly configured, with potentially disastrous results.
There are a number of management objects defined in these MIB modules
with a MAX-ACCESS clause of read-write and/or read-create. Such
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 28]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
network operations. These are the tables and objects and their
sensitivity/vulnerability:
o the gmplsInterfaceTable, gmplsInSegmentTable, gmplsOutSegmentTable
and gmplsLabelTable collectively contain objects to provision
GMPLS interfaces, LSPs and their associated parameters on a Label
Switching Router (LSR). Unauthorized write access to objects in
these tables, could result in disruption of traffic on the
network. This is especially true if an LSP has already been
established. The use of stronger mechanisms such as SNMPv3
security should be considered where possible. Specifically, SNMPv3
VACM and USM MUST be used with any SNMPv3 agent which implements
these MIB modules.
Some of the readable objects in these MIB modules "i.e., objects with
a MAX-ACCESS other than not-accessible" may be considered sensitive
or vulnerable in some network environments. It is thus important to
control even GET and/or NOTIFY access to these objects and possibly
to even encrypt the values of these objects when sending them over
the network via SNMP. These are the tables and objects and their
sensitivity/vulnerability:
o the gmplsInterfaceTable, gmplsInSegmentTable, gmplsOutSegmentTable
and gmplsLabelTable collectively show the LSP network topology and
its capabilities. If an Administrator does not want to reveal this
information, then these tables should be considered
sensitive/vulnerable.
SNMP versions prior to SNMPv3 did not include adequate security. Even
if the network itself is secure "for example by using IPSec", even
then, there is no control as to who on the secure network is allowed
to access and GET/SET "read/change/create/delete" the objects in
these MIB modules. It is RECOMMENDED that implementers consider the
security features as provided by the SNMPv3 framework "see [RFC3410],
section 8", including full support for the SNMPv3 cryptographic
mechanisms "for authentication and privacy".
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module, is properly configured to give access to
the objects only to those principals "users" that have legitimate
rights to indeed GET or SET "change/create/delete" them.
10. Acknowledgments
This draft extends [LSRMIB]. The authors would like to express their
gratitude to all those who worked on that earlier MIB document.
The authors would like to express their thanks to Dan Joyle for his
careful review and comments on early versions of the Label Table.
Special thanks to Joan Cucchiara and Len Nieman for their help with
compilation issues.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 29]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
11. IANA Considerations
MPLS related standards track MIB modules are rooted under the
mplsStdMIB subtree.
One of the MIB modules contained in this document extends tables
contained in MPLS MIB modules.
As requested in requested in the GMPLS-TC-STD-MIB [GMPLSTCMIB] the
two MIB modules contained in this document should be placed in the
mplsStdMIB subtree as well.
New assignments can only be made via a Standards Action as specified
in [RFC2434].
11.1. IANA Considerations for GMPLS-LSR-STD-MIB
The IANA is requested to assign { mplsStdMIB xx } to the
GMPLS-LSR-STD-MIB module specified in this document.
11.2. IANA Considerations for GMPLS-LABEL-STD-MIB
The IANA is requested to assign { mplsStdMIB xx } to the
GMPLS-LABEL-STD-MIB module specified in this document.
12. References
12.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J.,
Case, J., Rose, M., and S. Waldbusser, "Structure
of Management Information Version 2 (SMIv2)", STD
58, RFC 2578, April 1999.
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J.,
Case, J., Rose, M., and S. Waldbusser, "Textual
Conventions for SMIv2", STD 58, RFC 2579, April
1999.
[RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J.,
Case, J., Rose, M., and S. Waldbusser, "Conformance
Statements for SMIv2", STD 58, RFC 2580, April
1999.
[RFC2863] McCloghrie, K. and F. Kastenholtz, "The Interfaces
Group MIB", RFC 2863, June 2000.
[GMPLSArch] Mannie, E. (Editor), "Generalized Multiprotocol
Label Switching (GMPLS) Architecture", Internet
Draft <draft-many-gmpls-architecture-07.txt>, May
2003, work in progress.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 30]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
[GMPLSSonetSDH] Mannie, E., Papadimitriou, D. (Editors),
"Generalized Multi-Protocol Label Switching
Extensions for SONET and SDH Control", Internet
Draft <draft-ietf-ccamp-gmpls-sonet-sdh-08.txt>,
February 2003, work in progress.
[GMPLSTCMIB] Nadeau, T., Srinivasan, C., Farrel, A., Hall, T.,
and Harrison, E., "Definitions of Textual
Conventions for Multiprotocol Label Switching
(MPLS) Management", draft-ietf-ccamp-gmpls-te-mib-
03.txt, November 2003, work in progress.
[GMPLSTEMIB] Nadeau, T., Srinivasan, C., Farrel, A., Hall, T.,
and Harrison, E., "Generalized Multiprotocol Label
Switching (GMPLS) Traffic Engineering Management
Information Base", draft-ietf-ccamp-gmpls-te-mib-
03.txt, November 2003, work in progress.
[TCMIB] Nadeau, T., Cucchiara, J. (Editors) "Definitions of
Textual Conventions for Multiprotocol Label
Switching (MPLS) Management", Internet Draft
<draft-ietf-mpls-tc-mib-09.txt>, August 2003, work
in progress.
[LSRMIB] Srinivasan, C., Viswanathan, A. and T. Nadeau,
"Multiprotocol Label Switching (MPLS) Label
Switching Router (LSR) Management Information
Base", Internet Draft <draft-ietf-mpls-lsr-mib-
12.txt>, August 2003, work in progress.
12.2. Informational References
[RFC2026] S. Bradner, "The Internet Standards Process --
Revision 3", RFC 2026, October 1996.
[RFC2434] Narten, T. and H. Alvestrand, "Guidelines for
Writing an IANA Considerations Section in RFCs",
BCP: 26, RFC 2434, October 1998.
[RFC3031] Rosen, E., Viswanathan, A., and R. Callon,
"Multiprotocol Label Switching Architecture", RFC
3031, January 2001.
[RFC3209] Awduche, D., Berger, L., Gan, D., Li, T.,
Srinivasan, V., and G. Swallow, "RSVP-TE:
Extensions to RSVP for LSP Tunnels", RFC 3209,
December 2001.
[RFC3212] Jamoussi, B., Aboul-Magd, O., Andersson, L.,
Ashwood-Smith, P., Hellstrand, F., Sundell, K.,
Callon, R., Dantu, R., Wu, L., Doolan, P., Worster,
T., Feldman, N., Fredette, A., Girish, M., Gray,
E., Halpern, J., Heinanen, J., Kilty, T., Malis,
A., and P. Vaananen, "Constraint-Based LSP Setup
using LDP", RFC 3212, December 2001."
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 31]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
[RFC3410] Case, J., Mundy, R., Partain, D. and B. Stewart,
"Introduction and Applicability Statements for
Internet-Standard Management Framework", RFC 3410,
December 2002.
[RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An
Architecture for Describing Simple Network
Management Protocol (SNMP) Management Frameworks",
RFC 3411, December 2002.
[RFC3413] Levi, D., Meyer, P., Stewart, B., "SNMP
Applications", RFC 3413, December 2002.
[RFC3471] Berger, L. (Editor), "Generalized Multi-Protocol
Label Switching (GMPLS) Signaling Functional
Description", RFC 3471, January 2003.
[RFC3472] Ashwood-Smith, P., Berger, L. (Editors),
"Generalized MPLS Signaling - CR-LDP Extensions",
RFC 3472, January 2003.
[RFC3473] Berger, L. (Editor), "Generalized MPLS Signaling -
RSVP-TE Extensions", RFC 3473 January 2003.
[TEMIB] Nadeau, T., Srinivasan, C, Viswanathan, A.,
"Multiprotocol Label Switching (MPLS) Traffic
Engineering Management Information Base", Internet
Draft <draft-ietf-mpls-te-mib-12.txt>, August 2003,
work in progress.
13. Authors' Addresses
Thomas D. Nadeau
Cisco Systems, Inc.
300 Apollo Drive
Chelmsford, MA 01824
Phone: +1-978-244-3051
Email: tnadeau@cisco.com
Cheenu Srinivasan
Bloomberg L.P.
499 Park Ave.,
New York, NY 10022
Phone: +1-212-893-3682
Email: cheenu@bloomberg.net
Adrian Farrel
Old Dog Consulting
Phone: +44-(0)-1978-860944
Email: adrian@olddog.co.uk
Tim Hall
Data Connection Ltd.
100 Church Street
Enfield, Middlesex, EN2 6BQ, UK
Phone: +44 20 8366 1177
Email: timhall@dataconnection.com
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 32]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
Ed Harrison
Data Connection Ltd.
100 Church Street
Enfield, Middlesex, EN2 6BQ, UK
Phone: +44 20 8366 1177
Email: ed.harrison@dataconnection.com
14. Full Copyright Statement
Copyright (C) The Internet Society (2003). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph
are included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns. This
document and the information contained herein is provided on an "AS
IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK
FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN
WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
15. Intellectual Property Notice
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11 [RFC2028].
Copies of claims of rights made available for publication and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use
of such proprietary rights by implementers or users of this
specification can be obtained from the IETF Secretariat.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 33]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-03.txt November 2003
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive
Director.
16. Changes and Pending Work
This section must be removed before the draft progresses to RFC.
16.1. Pending Work
The following work items have been identified for this draft. They
will be addressed in a future version.
- Expand conformance statements to give one for monitoring only,
and one for monitoring and control.
- Provide support for monitoring tunnel resources in GMPLS systems.
For example, SONET/SDH or G.709. This might be done through an
arbitrary RowPointer to an external MIB.
- Extend the performance tables from the MPLS-LSR-MIB for
technology-specific GMPLS LSPs.
- Determine whether the 'discriminated union' in the Label Table is
good MIB.
16.1. Changes from version 2 to version 3
- Work on basic compilation issues.
- Provide a next index object to supply the next available
arbitrary index into the Label Table.
- Update references.
- Update examples.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 34]
Network Working Group Thomas D. Nadeau
Internet Draft Cisco Systems, Inc.
Expires: May 2004
Cheenu Srinivasan
Bloomberg L.P.
Adrian Farrel
Old Dog Consulting
Tim Hall
Ed Harrison
Data Connection Ltd.
November 2003
Definitions of Textual Conventions for Generalized Multi-Protocol
Label Switching (GMPLS) Management
draft-ietf-ccamp-gmpls-tc-mib-03.txt
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC 2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
Abstract
This document defines a Management Information Base (MIB) module
which contains Textual Conventions to represent commonly used
Generalized Multi-Protocol Label Switching (GMPLS) management
information. The intent is that these TEXTUAL CONVENTIONS (TCs) will
be imported and used in GMPLS related MIB modules that would
otherwise define their own representations.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 1]
Internet Draft draft-ietf-ccamp-gmpls-tc-mib-03.txt November 2003
Table of Contents
1. Introduction 2
2. The SNMP Management Framework 2
3. GMPLS Textual Conventions MIB Definitions 3
4. Security Considerations 5
5. IANA Considerations 5
6. References 5
6.1. Normative References 5
6.2. Informational References 6
7. Authors' Addresses 7
8. Full Copyright Statement 7
9. Intellectual Property Notice 8
1. Introduction
This document defines a MIB module which contains Textual Conventions
for Generalized Multi-Protocol Label Switching (GMPLS) networks.
These Textual Conventions should be imported by MIB modules which
manage GMPLS networks.
This MIB module supplements the MIB module in [TCMIB] that defines
Textual Conventions for Multiprotocol Label Switching (MPLS)
Management. [TCMIB] may continue to be used without this MIB module
in networks that support only MPLS.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
Comments should be made directly to the CCAMP mailing list at
ccamp@ops.ietf.org.
For an introduction to the concepts of GMPLS, see [GMPLSArch].
2. The SNMP Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a MIB
module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580].
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 2]
Internet Draft draft-ietf-ccamp-gmpls-tc-mib-03.txt November 2003
3. GMPLS Textual Conventions MIB Definitions
GMPLS-TC-STD-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY
FROM SNMPv2-SMI
transmission
FROM SNMPv2-SMI
TEXTUAL-CONVENTION
FROM SNMPv2-TC
;
gmplsTCStdMIB MODULE-IDENTITY
LAST-UPDATED
"200310300900Z" -- 30 October 2003 9:00:00 GMT"
ORGANIZATION "Common Control And Management Protocols (CCAMP)
Working Group"
CONTACT-INFO
" Thomas D. Nadeau
Cisco Systems, Inc.
Email: tnadeau@cisco.com
Cheenu Srinivasan
Bloomberg L.P.
Email: cheenu@bloomberg.net
Adrian Farrel
Old Dog Consulting
Email: adrian@olddog.co.uk
Ed Harrison
Data Connection Ltd.
Email: ed.harrison@dataconnection.com
Tim Hall
Data Connection Ltd.
Email: timhall@dataconnection.com
Comments about this document should be emailed direct to the
CCAMP working group mailing list at ccamp@ops.ietf.org"
DESCRIPTION
"Copyright (C) The Internet Society (2003). This version of this
MIB module is part of RFCXXX; see the RFC itself for full legal
notices.
This MIB module defines Textual Conventions for concepts used in
Generalized Multi-Protocol Label Switching (GMPLS) networks."
-- Revision history.
REVISION
"200310300900Z" -- 30 October 2003 09:00:00 GMT
DESCRIPTION
"Initial version published as part of RFC XXXX."
-- Please see the IANA Considerations Section.
-- The requested gmplsStdMIB subId is xx, i.e.
::= { gmplsStdMIB xx }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 3]
Internet Draft draft-ietf-ccamp-gmpls-tc-mib-03.txt November 2003
gmplsStdMIB OBJECT IDENTIFIER
-- This object identifier needs to be assigned by IANA.
-- Since mpls has been assigned an ifType of 166 we recommend
-- that this OID be 166 as well, i.e.
::= { transmission XXX }
-- Textual Conventions (sorted alphabetically).
GmplsFreeformLabel ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This value represents a freeform generalized MPLS Label. This
can be used to represent label types which are not standard
in the drafts. It may also be used by systems that do not
wish to represent the labels using the specific label types."
SYNTAX OCTET STRING (SIZE (0..64))
GmplsGeneralizedLabelTypes ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Determines the interpretation that should be applied to a
label."
SYNTAX INTEGER {
gmplsMplsLabel(1),
gmplsPortWavelengthLabel(2),
gmplsFreeformGeneralizedLabel(3),
gmplsSonetLabel(4),
gmplsSdhLabel(5),
gmplsWavebandLabel(6)
}
GmplsSegmentDirection ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The direction of data flow on an LSP segment with respect to the
head of the LSP.
Where an LSP is signaled using a conventional signaling
protocol, the 'head' of the LSP is the source of the signaling
(also known as the ingress) and the 'tail' is the destination
(also known as the egress).
For manually configured LSPs an arbitrary decision must be made
about which LER is the 'head'."
SYNTAX INTEGER {
forward(1),
reverse(2)
}
END
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 4]
Internet Draft draft-ietf-ccamp-gmpls-tc-mib-03.txt November 2003
4. Security Considerations
This module does not define any management objects. Instead, it
defines a set of textual conventions which may be used by other GMPLS
MIB modules to define management objects.
Meaningful security considerations can only be written in the MIB
modules that define management objects. Therefore, this document has
no impact on the security of the Internet.
5. IANA Considerations
IANA is requested to make a MIB OID assignment under the transmission
branch, that is, assign the gmplsStdMIB under { transmission 166 }.
This sub-id is requested because 166 is the ifType for mpls(166) and
is available under transmission.
In the future, GMPLS related standards track MIB modules should be
rooted under the mplsStdMIB (sic) subtree. IANA is requested to
manage that namespace. New assignments can only be made via a
Standards Action as specified in [RFC2434].
This document also requests IANA to assign { gmplsStdMIB xx } to the
GMPLS-TC-STD-MIB specified in this document.
6. References
6.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J.,
Case, J., Rose, M. and S. Waldbusser, "Structure of
Management Information Version 2 (SMIv2)", STD 58,
RFC 2578, April 1999.
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J.,
Case, J., Rose, M. and S. Waldbusser, "Textual
Conventions for SMIv2", STD 58, RFC 2579, April
1999.
[RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J.,
Case, J., Rose, M. and S. Waldbusser, "Conformance
Statements for SMIv2", STD 58, RFC 2580, April 1999.
[RFC3471] Berger, L. (Editor), "Generalized Multi-Protocol
Label Switching (GMPLS) Signaling Functional
Description", RFC 3471, January 2003.
[GMPLSArch] Mannie, E. (Editor), "Generalized Multiprotocol
Label Switching (GMPLS) Architecture", Internet
Draft <draft-many-gmpls-architecture-07.txt>, May
2003, work in progress.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 5]
Internet Draft draft-ietf-ccamp-gmpls-tc-mib-03.txt November 2003
6.2. Informational References
[RFC2434] Narten, T. and H. Alvestrand, "Guidelines for
Writing an IANA Considerations Section in RFCs",
BCP: 26, RFC 2434, October 1998.
[RFC3031] Rosen, E., Viswananthan, A., and R. Callon,
Multiprotocol Label Switching Architecture",
RFC 3031, January 2001.
[RFC3209] Awduche, D., Berger, L., Gan, D., Li, T.,
Srinivasan, V., Swallow, G., "RSVP-TE: Extensions to
RSVP for LSP Tunnels", RFC 3209, December 2001.
[RFC3212] Jamoussi, B., (editor), et. al. "Constraint-Based
LSP Setup using LDP", RFC 3212, January 2002.
[RFC3410] Case, J., Mundy, R., Partain, D. and B. Stewart,
"Introduction and Applicability Statements for
Internet-Standard Management Framework", RFC 3410,
December 2002.
[RFC3472] Ashwood-Smith, P., Berger, L. (Editors),
"Generalized MPLS Signaling - CR-LDP Extensions",
RFC 3472, January 2003.
[RFC3473] Berger, L. (Editor), "Generalized MPLS Signaling -
RSVP-TE Extensions", RFC 3473 January 2003.
[GMPLSSonetSDH] Mannie, E., Papadimitriou, D. (Editors),
"Generalized Multi-Protocol Label Switching
Extensions for SONET and SDH Control", Internet
Draft <draft-ietf-ccamp-gmpls-sonet-sdh-08.txt>,
February 2003, work in progress.
[GMPLSLSRMIB] Nadeau, T., Srinivasan, C., Farrel, A., Hall, T.,
and Harrison, E., " Generalized Multiprotocol Label
Switching (GMPLS) Label Switching Router (LSR)
Management Information Base", draft-ietf-ccamp-
gmpls-lsr-mib-03.txt, November 2003, work in
progress.
[GMPLSTEMIB] Nadeau, T., Srinivasan, C., Farrel, A., Hall, T.,
and Harrison, E., "Generalized Multiprotocol Label
Switching (GMPLS) Traffic Engineering Management
Information Base", draft-ietf-ccamp-gmpls-te-mib-
03.txt, November 2003, work in progress.
[TCMIB] Nadeau, T., Cucchiara, J. (Editors) "Definitions
of Textual Conventions for Multiprotocol Label
Switching (MPLS) Management", Internet Draft
<draft-ietf-mpls-tc-mib-09.txt>, August 2003,
work in progress.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 6]
Internet Draft draft-ietf-ccamp-gmpls-tc-mib-03.txt November 2003
7. Acknowledgements
Special thanks to Joan Cucchiara for her help with compilation
issues.
8. Authors' Addresses
Thomas D. Nadeau
Cisco Systems, Inc.
300 Apollo Drive
Chelmsford, MA 01824
Phone: +1-978-244-3051
Email: tnadeau@cisco.com
Cheenu Srinivasan
Bloomberg L.P.
499 Park Ave.,
New York, NY 10022
Phone: +1-212-893-3682
Email: cheenu@bloomberg.net
Adrian Farrel
Old Dog Consulting
Phone: +44-(0)-1978-860944
Email: adrian@olddog.co.uk
Tim Hall
Data Connection Ltd.
100 Church Street
Enfield, Middlesex
EN2 6BQ, UK
Phone: +44 20 8366 1177
Email: timhall@dataconnection.com
Ed Harrison
Data Connection Ltd.
100 Church Street
Enfield, Middlesex
EN2 6BQ, UK
Phone: +44 20 8366 1177
Email: ed.harrison@dataconnection.com
9. Full Copyright Statement
Copyright (C) The Internet Society (2003). All Rights Reserved.
This document and translations of it may be copied and furnished
to others, and derivative works that comment on or otherwise explain
it or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 7]
Internet Draft draft-ietf-ccamp-gmpls-tc-mib-03.txt November 2003
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns. This
document and the information contained herein is provided on an "AS
IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK
FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL
NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE.
10. Intellectual Property Notice
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11 [RFC2028].
Copies of claims of rights made available for publication and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive
Director.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 8]
| PAFTECH AB 2003-2026 | 2026-04-22 20:34:17 |