One document matched: draft-ietf-ccamp-gmpls-mln-extensions-00.txt
Network Working Group D. Papadimitriou (Alcatel)
Internet Draft M. Vigoureux (Alcatel)
Intended Status: Standards Track K. Shiomoto (NTT)
Created: November 4, 2007 D. Brungard (ATT)
Expires: May 4, 2008 J.L. Le Roux (France Telecom)
Generalized Multi-Protocol Label Switching (GMPLS) Protocol
Extensions for Multi-Layer and Multi-Region Networks (MLN/MRN)
draft-ietf-ccamp-gmpls-mln-extensions-00.txt
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other documents
at any time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Abstract
There are requirements for the support of networks ccomprising LSRs
with different data plane switching layers controlled by a single
Generalized Multi Protocol Label Switching (GMPLS) control plane
instance, referred to as GMPLS Multi-Layer Networks/Multi-Region
Networks (MLN/MRN). This document defines extensions to GMPLS routing
and signaling protocols so as to support the operation of GMPLS
Multi-Layer/Multi-Region Networks.
D.Papadimitriou et al. - Expires May 2008 [Page 1]
draft-ietf-ccamp-gmpls-mln-extensions-00.txt November 2007
Contents
1. Introduction ................................................... 3
1.1. Terminology .................................................. 3
1.1.1. Conventions Used in This Document .......................... 3
1.1.2. Assumed Concepts ........................................... 4
2. Summary of the Requirements and Evaluation ..................... 4
3. Interface Adaptation Capability Descriptor (IACD) .............. 4
3.1 Overview ...................................................... 5
3.2 Interface Adaptation Capability Descriptor (IACD) Format ...... 5
3.2.1 OSPF-TE ..................................................... 6
3.2.2 ISIS-TE ..................................................... 7
4. Multi-Region Signaling ......................................... 7
4.1 SC Subobject Encoding ......................................... 8
5. Virtual TE Link ................................................ 9
5.1 Edge-to-Edge Association ...................................... 9
5.1.1 CALL_ATTRIBUTES Object ..................................... 10
5.1.2 Processing ................................................. 10
5.1.3 Attributes TLVs ............................................ 11
5.1.4 Call Inheritance Flag ...................................... 12
5.2. Soft-FA Approach ............................................ 12
5.2.1 Pre-Planned LSP Flag ....................................... 12
5.2.2 Path Provisioned LSPs ...................................... 13
6. Backward Compatibility ........................................ 13
7. Security Considerations ....................................... 14
8. IANA Considerations............................................ 14
9. References .................................................... 14
9.1 Normative References ......................................... 14
9.2 Informative References ....................................... 15
D.Papadimitriou et al. - Expires May 2008 [Page 2]
draft-ietf-ccamp-gmpls-mln-extensions-00.txt November 2007
1. Introduction
Generalized Multi-Protocol Label Switching (GMPLS) [RFC3945]
extends MPLS to handle multiple switching technologies: packet
switching (PSC), layer-two switching (L2SC), TDM switching (TDM),
wavelength switching (LSC) and fiber switching (FSC). A GMPLS
switching type (PSC, TDM, etc.) describes the ability of a node to
forward data of a particular data plane technology, and uniquely
identifies a control plane region. LSP Regions are defined in
[RFC4206]. A network comprised of multiple switching types (e.g. PSC
and TDM) controlled by a single GMPLS control plane instance is
called a Multi-Region Network (MRN).
A data plane layer is a collection of network resources capable of
terminating and/or switching data traffic of a particular format.
For example, LSC, TDM VC-11 and TDM VC-4-64c represent three
different layers. A network comprising transport nodes with
different data plane switching layers controlled by a single GMPLS
control plane instance is called a Multi-Layer Network (MLN).
The applicability of GMPLS to multiple switching technologies
provides the unified control and operations for both LSP provisioning
and recovery [RFC4428]. This document covers the elements of a single
GMPLS control plane instance controlling multiple layers within a
given TE domain. A CP instance can serve one, two or more layers.
Other possible approaches such as having multiple CP instances
serving disjoint sets of layers are outside the scope of this
document.
The next sections provide the procedural aspects in terms of routing
and signaling for such environments as well as the extensions
required to instrument GMPLS to provide the capabilities for MLM/MRN
unified control. The rationales and requirements for Multi-
Layer/Region networks are set forth in [MLN-REQ]. These requirements
are evaluated against GMPLS protocols in [MLN-EVAL] and several
areas where GMPLS protocol extensions are required are identified.
This document defines GMPLS routing and signaling extensions so as
to cover GMPLS MLN/MRN requirements.
1.1. Terminology
1.1.1. Conventions Used in This Document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
D.Papadimitriou et al. - Expires May 2008 [Page 3]
draft-ietf-ccamp-gmpls-mln-extensions-00.txt November 2007
1.1.2. Assumed Concepts
In addition the reader is assumed to be familiar with the concepts
developed in [RFC3945], [RFC3471], and [RFC4202] as well as
[RFC4206] and [RFC4201].
2. Summary of the Requirements and Evaluation
As identified in [MLN-EVAL] most of MLN/MRN requirements rely on
mechanisms and procedures that are outside the scope of the GMPLS
protocols, and thus do not require any GMPLS protocol extensions.
They rely on local procedures and policies, and on specific TE
mechanisms and algorithms, which are outside the scope of GMPLS
protocols.
Four areas for extensions of GMPLS protocols and procedures have been
identified:
- GMPLS routing extension for the advertisement of the
internal adaptation capability of hybrid nodes.
- GMPLS signaling extension for constrained multi-region
signaling (SC inclusion/exclusion).
- GMPLS signaling extension for the setup/deletion of
Virtual TE-links (as well as exact trigger for its actual
provisioning).
- GMPLS routing and signaling extension for graceful TE-link
deletion (covered in [RFC5063]).
The first three requirements are addressed in Sections 3, 4 and 5,
respectively, of this document. The fourth one is addressed in
[RFC5063].
3. Interface adaptation capability descriptor (IACD)
In the MRN context, nodes supporting more than one switching
capability on at least one interface are called Hybrid nodes. Hybrid
nodes contain at least two distinct switching elements that are
interconnected by internal links to provide adaptation between the
supported switching capabilities. These internal links have finite
capacities and must be taken into account when computing the path of
a multi-region TE-LSP.
The advertisement of the internal adaptation capability is required
as it provides critical information when performing multi-region path
computation.
D.Papadimitriou et al. - Expires May 2008 [Page 4]
draft-ietf-ccamp-gmpls-mln-extensions-00.txt November 2007
3.1 Overview
In an MRN environment, some LSRs could contain, under the control of
a single GMPLS instance, multiple switching capabilities such as PSC
and TDM or PSC and Lambda Switching Capability (LSC).
These nodes, hosting multiple Interface Switching Capabilities
(ISC), just like other nodes (hosting a single Interface Switching
Capability) are required to hold and advertise resource information
on link states and topology. They also may have to consider certain
portions of internal node resources to terminate hierarchical label
switched paths (LSPs), since circuit switch capable units such as
TDMs, LSCs, and FSCs require rigid resources. For example, a node
with PSC+LSC hierarchical switching capability can switch a Lambda
LSP but may not be able to can never terminate the Lambda LSP if
there is no unused adaptation capability between the LSC and the PSC
switching capabilities.
Another example occurs when L2SC (Ethernet) switching can be adapted
in LAPS X.86 and GFP for instance before reaching the TDM switching
matrix. Similar circumstances can occur, if a switching fabric that
supports both PSC and L2SC functionalities is assembled with LSC
interfaces enabling "lambda" encoding. In the switching fabric, some
interfaces can terminate Lambda LSPs and perform frame (or cell)
switching whilst other interfaces can terminate Lambda LSPs and
perform packet switching.
Therefore, within multi-region networks, the advertisement of the
so-called adaptation capability to terminate LSPs (not the interface
capability since the latter can be inferred from the bandwidth
available for each switching capability) provides critical
information to take into account when performing multi-region path
computation. This concept enables a node to discriminate the remote
nodes (and thus allows their selection during path computation) with
respect to their adaptation capability e.g. to terminate LSPs at the
PSC or LSC level.
Hence, we introduce the idea of discriminating the (internal)
adaptation capability from the (interface) switching capability by
considering an interface adaptation capability descriptor.
A more detailed problem statement can be found in [MLN-EVAL].
3.2 Interface Adaptation Capability Descriptor (IACD) Format
The interface switching capability descriptor (IACD) provides the
information for the forwarding/switching) capability only.
D.Papadimitriou et al. - Expires May 2008 [Page 5]
draft-ietf-ccamp-gmpls-mln-extensions-00.txt November 2007
3.2.1 OSPF-TE
In OSPF, the IACD sub-TLV is defined as a sub-TLV of the Link TLV
(see [RFC3630]), with type TBD. The IACD sub-TLV format is defined
as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Switching Cap | Encoding | Switching Cap | Encoding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Max LSP Bandwidth at priority 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Max LSP Bandwidth at priority 1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Max LSP Bandwidth at priority 2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Max LSP Bandwidth at priority 3 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Max LSP Bandwidth at priority 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Max LSP Bandwidth at priority 5 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Max LSP Bandwidth at priority 6 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Max LSP Bandwidth at priority 7 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Adaptation Capability-specific information |
| (variable) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Where:
- first Switching Capability (SC) field (byte 1): lower switching
capability (as defined for the existing ISC sub-TLV)
- first Encoding field (byte 2): as defined for the existing ISC
sub-TLV
- second SC value (byte 3): upper switching capability (new)
- second encoding value (byte 4): set to the encoding of the
available adaptation pool and to 0xFF when the corresponding SC
value has no access to the wire (i.e. there is no ISC sub-TLV for
this upper switching capability)
Multiple IACD sub-TLVs may be present within a given TE Link TLV
and the bandwidth simply provides an indication of resources still
available to perform insertion/ extraction for a given adaptation
(pool concept).
D.Papadimitriou et al. - Expires May 2008 [Page 6]
draft-ietf-ccamp-gmpls-mln-extensions-00.txt November 2007
3.2.2 ISIS-TE
In IS-IS, the IACD sub-TLV is a sub-TLV of the Extended IS
Reachability TLV (see [RFC3784]) with type TBD. The IACD sub-TLV
format is defined as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Switching Cap | Encoding | Switching Cap | Encoding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Max LSP Bandwidth at priority 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Max LSP Bandwidth at priority 1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Max LSP Bandwidth at priority 2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Max LSP Bandwidth at priority 3 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Max LSP Bandwidth at priority 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Max LSP Bandwidth at priority 5 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Max LSP Bandwidth at priority 6 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Max LSP Bandwidth at priority 7 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Adaptation Capability-specific information |
| (variable) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Where the fields have the same processing and interpretation rules
as for Section 3.2.1.
Multiple IACD sub-TLVs may be present within a given extended IS
reachability TLV and the bandwidth simply provides an indication of
resources still available to perform insertion/ extraction for a
given adaptation (pool concept).
4. Multi-Region Signaling
Section 8.2 of [RFC4206] specifies that when a region boundary node
receives a Path message, the node determines whether it is at the
edge of an LSP region with respect to the ERO carried in the
message. If the node is at the edge of a region, it must then
determine the other edge of the region with respect to the ERO,
using the IGP database. The node then extracts from the ERO the
subsequence of hops from itself to the other end of the region.
D.Papadimitriou et al. - Expires May 2008 [Page 7]
draft-ietf-ccamp-gmpls-mln-extensions-00.txt November 2007
The node then compares the subsequence of hops with all existing FA-
LSPs originated by the node:
- If a match is found, that FA-LSP has enough unreserved bandwidth
for the LSP being signaled, and the PID of the FA-LSP is
compatible with the PID of the LSP being signaled, the node uses
that FA-LSP as follows. The Path message for the original LSP is
sent to the egress of the FA-LSP. The PHOP in the message is the
address of the node at the head-end of the FA-LSP. Before sending
the Path message, the ERO in that message is adjusted by removing
the subsequence of the ERO that lies in the FA-LSP, and replacing
it with just the end point of the FA-LSP.
- If no existing FA-LSP is found, the node sets up a new FA-LSP.
That is, it initiates a new LSP setup just for the FA-LSP.
Applying this procedure, in a MRN environment MAY lead to setup one-
hop FA-LSPs between each node. Therefore, considering that the path
computation is able to take into account richness of information with
regard to the SC available on given nodes belonging to the path, it
is consistent to provide enough signaling information to indicate the
SC to be used and on over which link. Particularly, in case a TE
link has multiple SC advertised as part of its ISCD sub-TLVs, an ERO
does not allow selecting a particular SC.
Limiting modifications to existing RSVP-TE procedures [RFC3473] and
referenced, this document defines a new sub-object of the eXclude
Route Object [RFC4874], called Switching Capability sub-object. This
sub-object enables (when desired) the explicit identification of (at
least one) switching capability to be excluded from the resource
selection process described here above.
Including this sub-object as part of the XRO that explicitly
indicates which SCs have to be excluded (before initiating the
procedure described here above) over a specified TE link solves the
ambiguous choice among SCs that are potentially used along a given
path and give the possibility to optimize resource usage on a multi-
region basis. Note that implicit SC inclusion is easily supported by
explicitly excluding other SCs (e.g. to include LSC, it is required
to exclude PSC, L2SC, TDM and FSC).
Note: usage of the Explicit Exclusion Route Subobject (EXRS) is
under investigation.
4.1 SC Subobject Encoding
The contents of an EXCLUDE_ROUTE object defined in [RFC4874] are a
series of variable-length data items called subobjects. This
document defines the SC subobject of the XRO (Type TBD), its
encoding and processing.
D.Papadimitriou et al. - Expires May 2008 [Page 8]
draft-ietf-ccamp-gmpls-mln-extensions-00.txt November 2007
Subobject Type TBD: Switching Capability
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|L| Type | Length | Attribute | Switching Cap |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
L
0 indicates that the attribute specified MUST be excluded
1 indicates that the attribute specified SHOULD be avoided
Attribute
0 reserved value
1 indicates that the specified SC should be excluded or
avoided with respect to the preceding numbered (Type 1 or
Type 2) or unnumbered interface (Type) subobject
Switching Cap (8-bits)
Switching Capability value to be excluded.
This sub-object must follow the set of numbered or unnumbered
interface sub-objects to which this sub-object refers. In case, of
loose hop ERO subobject, the XRO sub-object must precede the loose-
hop sub-object identifying the tail-end node/interface of the
traversed region(s).
Furthermore, it is expected, when label sub-object are following
numbered or unnumbered interface sub-objects, that the label value is
compliant with the SC capability to be explicitly excluded.
5. Virtual TE link
Two techniques can be used for the setup operation and maintenance of
Virtual TE links. The corresponding GMPLS protocols extensions are
described in this section.
5.1 Edge-to-edge Association
This approach that does not require state maintenance on transit LSRs
relies on extensions to the GMPLS RSVP-TE Call procedure [RFC4974].
This technique consists of exchanging identification and TE
attributes information directly between TE link end points. These TE
link end-points correspond to the LSP head-end and tail-end points of
of the LSPs that will be established. The end-points MUST belong to
the same (LSP) region through the establishment of a call between
D.Papadimitriou et al. - Expires May 2008 [Page 9]
draft-ietf-ccamp-gmpls-mln-extensions-00.txt November 2007
terminating LSRs.
Once the call is established the resulting association populates the
local TEDB and the resulting TE link is advertised as any other TE
link. The latter can then be used to attract traffic. Once an upper
layer/lower region LSP makes use of this TE link. A set of one or
more LSPs must be initially established before the FA LSP can be used
for nesting the incoming LSP.
In order to distinguish usage of such call from a classical call (as
defined e.g. in [RFC4139]), a CALL ATTRIBUTES object is introduced.
5.1.1 CALL_ATTRIBUTES Object
The CALL_ATTRIBUTES object is used to signal attributes required in
support of a call, or to indicate the nature or use of a call. It is
built on the LSP-ATTRIBUTES object defined in [RFC4420].
The CALL_ATTRIBUTES object class is 201 (TBD by IANA) of the form
11bbbbbb. This C-Num value (see [RFC2205], Section 3.10) ensures that
LSRs that do not recognize the object pass it on transparently.
One C-Type is defined, C-Type = 1 for CALL Attributes. This object is
optional and may be placed on Notify messages to convey additional
information about the desired attributes of the call.
5.1.2 Processing
Specifically, if an egress (or intermediate) LSR does not support the
object, it forwards it unexamined and unchanged. This facilitates
the exchange of attributes across legacy networks that do not support
this new object.
The CALL_ATTRIBUTES object may be used to report call operational
state on a Notify message.
CALL_ATTRIBUTES class = 201, C-Type = 1
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
// Attributes TLVs //
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The Attributes TLVs are encoded as described in Section 3.
D.Papadimitriou et al. - Expires May 2008 [Page 10]
draft-ietf-ccamp-gmpls-mln-extensions-00.txt November 2007
5.1.3 Attributes TLVs
Attributes carried by the CALL_ATTRIBUTES object are encoded within
TLVs. One or more TLVs may be present in each object.
There are no ordering rules for TLVs, and no interpretation should be
placed on the order in which TLVs are received.
Each TLV is encoded as follows.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
// Value //
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
The identifier of the TLV.
Length
The length of the Value field in bytes. Thus, if no Value
field is present the Length field contains the value zero.
Each Value field must be zero padded at the end to take it up
to a four byte boundary -- the padding is not included in the
length so that a one byte value would be encoded in an eight
byte TLV with Length field set to one.
Value
The data for the TLV padded as described above.
TLV Type 1 indicates the Attributes Flags TLV. Other TLV types may be
defined in the future with type values assigned by IANA (see Section
11.2). The Attributes Flags TLV may be present in a CALL_ATTRIBUTES
object.
The Attribute Flags TLV value field is an array of units of 32 flags
numbered from the most significant bit as bit zero. The Length field
for this TLV is therefore always a multiple of 4 bytes, regardless of
the number of bits carried and no padding is required.
Unassigned bits are considered as reserved and MUST be set to zero on
transmission by the originator of the object. Bits not contained in
the TLV MUST be assumed to be set to zero. If the TLV is absent
D.Papadimitriou et al. - Expires May 2008 [Page 11]
draft-ietf-ccamp-gmpls-mln-extensions-00.txt November 2007
either because it is not contained in the CALL_ATTRIBUTES object or
because this object is itself absent, all processing MUST be
performed as though the bits were present and set to zero. That is to
say, assigned bits that are not present either because the TLV is
deliberately foreshortened or because the TLV is not included MUST be
treated as though they are present and are set to zero.
5.1.4 Call inheritance Flag
This document introduces a specific flag (MSB position bit 0) of the
Attributes Flags TLV, to indicate that the association initiated
between the end-points belonging to a call results into a (virtual)
TE link advertisement.
The Call inheritance flag MUST be set to 1 in order to indicate that
the established association is to be translated into a TE link
advertisement. The value of this flag is by default set to 1. Setting
this flag to 0 results in a hidden TE link or in deleting the
corresponding TE link advertisement (by setting the corresponding
Opaque LSA Age to MaxAge [RFC2370]).
The notify message used for establishing the association is defined
as per [RFC4974]. Additionally, the notify message must carry an
LSP_TUNNEL_INTERFACE_ID Object, that allows identifying unnumbered
FA-LSPs ([RFC3477], [RFC4206], [RFC4206-bis]) and numbered FA-LSPs
([RFC4206], [RFC4206-bis]).
5.2. Soft-FA approach
The Soft Forwarding Adjacency (Soft FA) approach consists of setting
up the FA LSP at the control plane level without actually committing
resources in the data plane. This means that the corresponding LSP
exists only in the control plane domain.
Once such FA is established the corresponding TE link can be
advertized following the procedures described in [RFC4206].
5.2.1 Pre-planned LSP Flag
The LSP ATTRIBUTES object and Attributes Flags TLV are defined in
[RFC4420]. The present document defines a new flag, the pre-planned
LSP Flag, in the existing Attributes Flags TLV (numbered as Type 1).
The position of this flag is TBD in accordance with IANA assignment.
This flag, part of the LSP_REQUIRED ATTRIBUTE object, follows
processing of [RFC4420] for that object. That is, LSRs that do not
recognize the object reject the LSP setup effectively saying that
they do not support the attributes requested. Indeed, the newly
defined attribute requires examination at all transit LSRs.
D.Papadimitriou et al. - Expires May 2008 [Page 12]
draft-ietf-ccamp-gmpls-mln-extensions-00.txt November 2007
The pre-planned LSP Flag can take one of the following values:
o) When set to 0 this means that the LSP should be fully provisioned.
Absence of this flag (hence corresponding TLV) is therefore compliant
with the signaling message processing per [RFC3473])
o) When set to 1 this means that the LSP should be provisioned in the
control plane only.
If an LSP is established with the pre-planned Flag set to 1, no
resources are committed at the data plane level. The operation of
committing data plane resources occurs by re-signaling the same LSP
with the pre-planned Flag set to 0. It is RECOMMENDED that no other
modifications are made to other RSVP objects during this operation.
That is each intermediate node, processing a Flag transiting from 1
to 0 shall only be concerned with the commitment of data plane
resources and no other modification of the LSP properties and/or
attributes.
If an LSP is established with the pre-planned Flag set to 0, it MAY
be re-signaled by setting the Flag to 1.
5.2.2 Path Provisioned LSPs
There is a difference in between an LSP that is established with 0
bandwidth (path provisioning) and an LSP that is established with a
certain bandwidth value not committed at the data plane level (i.e.
pre-planned LSP).
However, the former is currently not possible using the GMPLS
protocol suite (following technology specific SENDER_TSPEC/FLOWSPEC
definition). Indeed, Traffic Parameters such as those defined in [RFC
4606] do not support setup of 0 bandwidth LSPs.
Mechanisms for provisioning (pre-planned or not) LSP with 0 bandwidth
will be described in next release of this document.
6. Backward compatibility
New objects and procedures defined in this document are running
within a given TE domain. The latter is expected to run in the
context of a consistent TE policy.
In such TE domains, we distinguish between edge LSRs and intermediate
LSRs. Edge LSRs must be able to process Call Attribute as defined in
section 5.1 if this is method selected or creating edge-to-edge
associations. In that domain, intermediate LSRs are by definition
transparent to the Call processing.
In case the Soft FA method is used for the creation of Virtual TE
D.Papadimitriou et al. - Expires May 2008 [Page 13]
draft-ietf-ccamp-gmpls-mln-extensions-00.txt November 2007
links, edge and intermediate LSRs must support processing of the LSP
ATTRIBUTE object per Section 5.2.
7. Security Considerations
In its current version, this memo does not introduce new security
consideration from the ones already detailed in the GMPLS protocol
suite.
8. IANA Considerations
This section to be completed in a future version of the document.
9. References
9.1 Normative References
[MLN-EVAL] J.-L. Leroux et al., "Evaluation of existing GMPLS
Protocols against Multi Region and Multi Layer Networks
(MRN/MLN)", Work in Progress, draft-ietf-ccamp-gmpls-mln-
eval.
[MLN-REQ] K.Shiomoto et al., "Requirements for GMPLS-based multi-
region and multi-layer networks (MRN/MLN)", Work in
Progress, draft-ietf-ccamp-gmpls-mln-reqs.
[RFC2119] Bradner, S., 'Key words for use in RFCs to indicate
requirements levels', RFC 2119, March 1997.
[RFC2205] Braden, R., Ed., Zhang, L., Berson, S., Herzog, S., and
S. Jamin, "Resource ReSerVation Protocol (RSVP) --
Version 1 Functional Specification", RFC 2205, September
1997.
[RFC2370] R.Coltun, "The OSPF Opaque LSA Option", RFC 2370, July
1998.
[RFC3471] L.Berger et al., "Generalized Multi-Protocol Label
Switching (GMPLS) - Signaling Functional Description",
RFC 3471, January 2003.
[RFC3473] Berger, L., Ed., "Generalized Multi-Protocol Label
Switching (GMPLS) Signaling Resource ReserVation
Protocol-Traffic Engineering (RSVP-TE) Extensions", RFC
3473, January 2003.
[RFC3477] Kompella, K. and Y. Rekhter, "Signalling Unnumbered Links
in Resource ReSerVation Protocol - Traffic Engineering
(RSVP-TE)", RFC 3477, January 2003.
D.Papadimitriou et al. - Expires May 2008 [Page 14]
draft-ietf-ccamp-gmpls-mln-extensions-00.txt November 2007
[RFC3630] D.Katz et al., "Traffic Engineering (TE) Extensions to
OSPF Version 2," RFC 3630, September 2003.
[RFC3784] H.Smit and T.Li, "Intermediate System to Intermediate
System (IS-IS) Extensions for Traffic Engineering (TE)",
RFC 3784, June 2004.
[RFC3945] Mannie, E., Ed., "Generalized Multi-Protocol Label
Switching (GMPLS) Architecture", RFC 3945, October 2004.
[RFC4201] K.Kompella, et al., "Link Bundling in MPLS Traffic
Engineering", RFC 4201, October 2005.
[RFC4202] K.Kompella (Editor), Y. Rekhter (Editor) et al. "Routing
Extensions in Support of Generalized MPLS", RFC 4202,
October 2005.
[RFC4206] K.Kompella and Y.Rekhter, "LSP Hierarchy with Generalized
MPLS TE", RFC 4206, October 2005.
[RFC4206-bis] Shimoto et al. " Procedures for Dynamically Signaled
Hierarchical Label Switched Paths ", draft-ietf-ccamp-
lsp-hierarchy-bis, work in progress.
[RFC4420] A.Farrel et al., "Encoding of Attributes for
Multiprotocol Label Switching (MPLS) Label Switched Path
(LSP) Establishment Using Resource ReserVation Protocol-
Traffic Engineering (RSVP-TE)", RFC 4420, February 2006.
[RFC4874] C.Y.Lee, A.Farrel, and S.DeCnodder, "Exclude Routes -
Extension to Resource ReserVation Protocol-Traffic
Engineering (RSVP-TE)", RFC 4874, April 2007.
[RFC4974] D.Papadimitriou and A.Farrel, "Generalized MPLS (GMPLS)
RSVP-TE Signaling Extensions in Support of Calls", RFC
4974, August 2007.
[RFC5063] A.Satyanarayana and R. Rahman, "Extensions to GMPLS
Resource Reservation Protocol (RSVP) Graceful Restart",
RFC 5063, October 2007.
9.2 Informative References
[MLRT] W.Imajuku et al., "Multilayer routing using multilayer
switch capable LSRs, Work in Progress, draft-imajuku-ml-
routing.
D.Papadimitriou et al. - Expires May 2008 [Page 15]
draft-ietf-ccamp-gmpls-mln-extensions-00.txt November 2007
[RFC4139] D.Papadimitriou et al., "Requirements for Generalized
MPLS (GMPLS) Signaling Usage and Extensions for
Automatically Switched Optical Network (ASON)", RFC 4139,
July 2005.
[RFC4428] D.Papadimitriou et al. "Analysis of Generalized Multi-
Protocol Label Switching (GMPLS)-based Recovery
Mechanisms (including Protection and Restoration)", RFC
4428, March 2006.
Acknowledgments
The authors would like to thank Mr. Wataru Imajuku for the
discussions on adaptation between regions [MLRT].
Author's Addresses
Dimitri Papadimitriou
Alcatel-Lucent Bell
Copernicuslaan 50
B-2018 Antwerpen, Belgium
Phone : +32 3 240 8491
E-mail: dimitri.papadimitriou@alcatel-lucent.be
Martin Vigoureux
Alcatel-Lucent France
Route de Villejust
91620 Nozay, France
Tel : +33 1 30 77 26 69
Email: martin.vigoureux@alcatel-lucent.fr
Kohei Shiomoto
NTT Network Service Systems Laboratories
3-9-11 Midori-cho
Musashino-shi, Tokyo 180-8585, Japan
Phone: +81 422 59 4402
E-mail: shiomoto.kohei@lab.ntt.co.jp
Deborah Brungard
AT&T
Rm. D1-3C22 - 200 S. Laurel Ave.
Middletown, NJ 07748, USA
Phone: +1 732 420 1573
E-mail: dbrungard@att.com
D.Papadimitriou et al. - Expires May 2008 [Page 16]
draft-ietf-ccamp-gmpls-mln-extensions-00.txt November 2007
Jean-Louis Le Roux
FTRD/DAC/LAN
Avenue Pierre Marzin
22300 Lannion, France
Phone: +33 (0)2 96 05 30 20
E-mail:jean-louis.leroux@rd.francetelecom.com
Contributors
Eiji Oki
NTT Network Service Systems Laboratories
3-9-11 Midori-cho
Musashino-shi, Tokyo 180-8585, Japan
Phone : +81 422 59 3441
Email: oki.eiji@lab.ntt.co.jp
Ichiro Inoue
NTT Network Service Systems Laboratories
3-9-11 Midori-cho
Musashino-shi, Tokyo 180-8585, Japan
Phone : +81 422 59 6076
Email: ichiro.inoue@lab.ntt.co.jp
Emmanuel Dotaro
Alcatel-Lucent France
Route de Villejust
91620 Nozay, France
Phone : +33 1 6963 4723
Email: emmanuel.dotaro@alcatel-lucent.fr
Gert Grammel
Alcatel-Lucent SEL
Lorenzstrasse, 10
70435 Stuttgart, Germany
Email: gert.grammel@alcatel-lucent.de
Full Copyright Statement
Copyright (C) The IETF Trust (2007).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
D.Papadimitriou et al. - Expires May 2008 [Page 17]
draft-ietf-ccamp-gmpls-mln-extensions-00.txt November 2007
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use
of such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgment
Funding for the RFC Editor function is provided by the IETF
Administrative Support Activity (IASA).
D.Papadimitriou et al. - Expires May 2008 [Page 18]
| PAFTECH AB 2003-2026 | 2026-04-22 19:07:38 |