One document matched: draft-ietf-ccamp-gmpls-lsr-mib-05.txt
Differences from draft-ietf-ccamp-gmpls-lsr-mib-04.txt
Network Working Group Thomas D. Nadeau
Internet Draft Cisco Systems, Inc.
Proposed Status: Standards Track
Expires: December 2004 Cheenu Srinivasan
Bloomberg L.P.
Adrian Farrel
Old Dog Consulting
Tim Hall
Ed Harrison
Data Connection Ltd.
June 2004
Generalized Multiprotocol Label Switching (GMPLS)
Label Switching Router (LSR) Management Information Base
draft-ietf-ccamp-gmpls-lsr-mib-05.txt
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC 2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other documents
at any time. It is inappropriate to use Internet-Drafts as
reference material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects to configure and/or
monitor a Generalized Multiprotocol Label Switching (GMPLS) Label
Switching Router (LSR).
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 1]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
Table of Contents
1. Introduction 2
1.1. Migration Strategy 2
2. Terminology 3
3. The SNMP Management Framework 3
4. Outline 3
4.1. Summary of the GMPLS LSR MIB Module 4
4.1.1 Summary of the GMPLS LSR MIB Module 4
4.1.2 Summary of the GMPLS Label MIB Module 4
5. Bidirectional LSPs 5
6. Example of LSP Setup 5
7. GMPLS Label Switching Router MIB Definitions 9
8. GMPLS Label MIB Definitions 18
9. Security Considerations 29
10. Acknowledgments 30
11. IANA Considerations 30
11.1. IANA Considerations for GMPLS-LSR-STD-MIB 30
11.2. IANA Considerations FOR GMPLS-LABEL-STD-MIB 31
12. References 31
12.1. Normative References 31
12.2. Informational References 32
13. Authors' Addresses 33
14. Full Copyright Statement 33
15. Intellectual Property Notice 34
1. Introduction
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects for modeling a
Generalized Multiprotocol Label Switching (GMPLS) [GMPLSArch] Label
Switching Router (LSR).
Comments should be made directly to the CCAMP mailing list at
ccamp@ops.ietf.org.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119, reference
[RFC2119].
1.1. Migration Strategy
There are two MIB modules in this document. The GMPLS LSR MIB module
extends the LSR MIB module defined for use with MPLS [LSRMIB]. The
only changes made are additions for support of GMPLS or changes that
are necessary to support the increased complexity of a GMPLS system.
The GMPLS Label MIB module may be referenced using a row pointer from
objects within the LSR MIB module.
The companion document modeling and managing GMPLS based traffic
engineering [GMPLSTEMIB] extends the MPLS TE MIB module [TEMIB] with
the same intentions.
Textual conventions and OBJECT-IDENTIFIERS are defined in
[GMPLSTCMIB] which extends the set of textual conventions originally
defined in [TCMIB].
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 2]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
2. Terminology
This document uses terminology from the document describing the MPLS
architecture [RFC3031] and the GMPLS architecture [GMPLSArch].
A label switched path (LSP) is modeled as a connection consisting of
one or more incoming segments (in-segments) and/or one or more
outgoing segments (out-segments) at an LSR. The association or
interconnection of the in-segments and out-segments is accomplished
by using a cross-connect. We use the terminology "connection" and
"LSP" interchangeably where the meaning is clear from the context.
in-segment This is analogous to a GMPLS label on an interface.
out-segment This is analogous to a GMPLS label on an interface.
cross-connect This describes the conceptual connection between a
set of in-segments and out-segments.
Note that either set may be empty; for example, a
cross-connect may connect only out-segments
together with no in-segments in the case where an
LSP is originating on an LSR.
3. The SNMP Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a
MIB module that is compliant to the SMIv2, which is described in STD
58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC
2580 [RFC2580].
4. Outline
Configuring statically provisioned GMPLS LSPs through an LSR involves
the following steps:
- Configuring an interface using the MPLS LSR MIB module.
- Enabling GMPLS on GMPLS capable interfaces using this MIB module.
- Configuring in-segments and out-segments using the MPLS LSR MIB
module.
- Configuring GMPLS extensions to the in-segments and out-segments
using this MIB module.
- Setting up the cross-connect table in the MPLS LSR MIB module to
associate segments and/or to indicate connection origination and
termination.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 3]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
- Optionally setting up labels in the label table in this MIB module
if the textual convention MplsLabel is not capable of holding the
required label (for example, if the label requires more than 32
bits to encode it), or if the operator wishes to disambiguate
GMPLS label types.
- Optionally specifying label stack actions in the MPLS LSR MIB
module.
- Optionally specifying segment traffic parameters in the MPLS LSR
MIB module.
4.1 MIB Modules
There are two MIB modules defined in this document.
The GMPLS LSR MIB module contains tables that extend tables defined
in the MPLS LSR MIB module. This MIB module is used in conjunction
with the MPLS LSR MIB module in systems that support GMPLS.
The GMPLS Label MIB module contains objects for managing GMPLS labels
when they cannot be represented using the textual conventions of the
MPLS TC MIB module, or when more detailed access to the sub-fields of
the labels is required.
4.1.1 Summary of the GMPLS LSR MIB Module
The MIB tables in this MIB module are as follows.
- The interface configuration table (gmplsInterfaceTable), which
extends mplsInterfaceTable to enable the GMPLS protocol on MPLS-
capable interfaces.
- The in-segment (gmplsInSegmentTable) and out-segment
(gmplsOutSegmentTable) tables extend mplsInSegmentTable and
mplsOutSegmentTable to configuring GMPLS-specific parameters for
LSP segments at an LSR.
These tables are described in the subsequent sections.
4.1.2 Summary of the GMPLS Label MIB Module
There is one MIB table in this MIB module as follows.
- The gmplsLabelTable allows Generalized
Labels to be defined and managed in a central location.
Generalized Labels can be of variable length and have distinct
bit-by-bit interpretations according to the use that is made of
them.
These tables are described in the subsequent sections.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 4]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
5. Bidirectional LSPs
This MIB module supports bidirectional LSPs as required for GMPLS.
A single value of mplsXCIndex is shared by all of the segments for
the entire bidirectional LSP. This facilitates a simple reference
from [TEMIB] and [GMPLSTEMIB], and makes fate-sharing more obvious.
It is, however, important that the direction of segments is
understood to avoid connecting all in-segments to all out-segments.
This is achieved by an object in each segment that indicates the
direction of the segment with respect to data flow.
A segment that is marked as 'forward' carries data from the 'head' of
the LSP to the 'tail'. A segment marked as 'reverse' carries data in
the reverse direction.
Where an LSP is signaled using a conventional signaling protocol, the
'head' of the LSP is the source of the signaling (also known as the
ingress) and the 'tail' is the destination (also known as the
egress). For manually configured LSPs an arbitrary decision must be
made about which segments are 'forward' and which 'reverse'. For
consistency this decision should be made across all LSRs that
participate in the LSP by assigning 'head' and 'tail' ends to the
LSP.
6. Example of LSP Setup
In this section we provide a brief example of using the MIB objects
described in sections 7 and 8 to set up an LSP. While this example is
not meant to illustrate every nuance of the MIB, it is intended as an
aid to understanding some of the key concepts. It is meant to be read
after going through the MIB itself. A prerequisite is an
understanding of [LSRMIB].
Suppose that one would like to manually create a best-effort, bi-
directional LSP. Assume that, in the forward direction, the LSP
enters the LSR via MPLS interface A with ifIndex 12 and exits the LSR
via MPLS interface B with ifIndex 13. For the reverse direction, we
assume the LSP enters via interface B and leaves via interface A
(i.e. the forward and reverse directions use the same bi-directional
interfaces). Let us also assume that we do not wish to have a label
stack beneath the top label on the outgoing labeled packets. The
following example illustrates which rows and corresponding objects
might be created to accomplish this.
We must first create rows in the gmplsLabelTable corresponding to the
labels required for each of the forward and reverse direction in- and
out-segments. For the purpose of this example the forward and
reverse labels on each interface will be the same, hence we need to
create just two rows in the gmplsLabelTable - one for each interface.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 5]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
In gmplsLabelTable:
{
gmplsLabelInterface = 12,
gmplsLabelIndex = 1,
gmplsLabelSubindex = 0,
gmplsLabelType = gmplsFreeformGeneralizedLabel(3),
gmplsLabelFreeform = 0x123456789ABCDEF0
gmplsLabelRowStatus = createAndGo(4)
}
In gmplsLabelTable:
{
gmplsLabelInterface = 13,
gmplsLabelIndex = 1,
gmplsLabelSubindex = 0,
gmplsLabelType = gmplsFreeformGeneralizedLabel(3),
gmplsLabelFreeform = 0xFEDCBA9876543210
gmplsLabelRowStatus = createAndGo(4)
}
We must next create the appropriate in-segment and out-segment
entries. These are done in [LSRMIB] using the mplsInSegmentTable and
mplsOutSegmentTable. Note that we use a row pointer to the two rows
in the gmplsLableTable rather than specifying the labels explicitly
in the in- and out-segment tables. Also note that the row status for
each row is set to createAndWait(5) to allow corresponding entries in
the gmplsInSegmentTable and gmplsOutSegmentTable to be created.
For the forward direction.
In mplsInSegmentTable:
{
mplsInSegmentIndex = 0x00000015
mplsInSegmentLabel = 0, -- incoming label in label =
table
mplsInSegmentNPop = 1,
mplsInSegmentInterface = 12, -- incoming interface
-- RowPointer MUST point to the first accesible column.
mplsInSegmentTrafficParamPtr = 0.0,
mplsInSegmentLabelPtr = gmplsLabelTable (12, 1, 0)
mplsInSegmentRowStatus = createAndWait(5)
}
In mplsOutSegmentTable:
{
mplsOutSegmentIndex = 0x00000012,
mplsOutSegmentInterface = 13, -- outgoing interface
mplsOutSegmentPushTopLabel = true(1),
mplsOutSegmentTopLabel = 0, -- outgoing label in label =
table
-- RowPointer MUST point to the first accesible column.
mplsOutSegmentTrafficParamPtr = 0.0,
mplsOutSegmentLabelPtr = gmplsLabelTable (13, 1, 0)
mplsOutSegmentRowStatus = createAndWait(5)
}
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 6]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
For the reverse direction.
In mplsInSegmentTable:
{
mplsInSegmentIndex = 0x00000016
mplsInSegmentLabel = 0, -- incoming label in label =
table
mplsInSegmentNPop = 1,
mplsInSegmentInterface = 13, -- incoming interface
-- RowPointer MUST point to the first accesible column.
mplsInSegmentTrafficParamPtr = 0.0,
mplsInSegmentLabelPtr = gmplsLabelTable (13, 1, 0)
mplsInSegmentRowStatus = createAndWait(5)
}
In mplsOutSegmentTable:
{
mplsOutSegmentIndex = 0x00000013,
mplsOutSegmentInterface = 12, -- outgoing interface
mplsOutSegmentPushTopLabel = true(1),
mplsOutSegmentTopLabel = 0, -- outgoing label in label =
table
-- RowPointer MUST point to the first accesible column.
mplsOutSegmentTrafficParamPtr = 0.0,
mplsOutSegmentLabelPtr = gmplsLabelTable (12, 1, 0)
mplsOutSegmentRowStatus = createAndWait(5)
}
These table entries are extended by entries in gmplsInSegmentTable
and gmplsOutSegmentTable. Note that the nature of the 'extends'
relationship is that the entry in gmplsInSegmentTable has the same
index values as the entry in mplsInSegmentTable. Similarly, the entry
in gmplsOutSegmentTable has the same index values as the entry in
mplsOutSegmentTable.
First for the forward direction:
In gmplsInSegmentTable(0x00000015)
{
gmplsInSegmentDirection = forward (1)
}
In gmplsOutSegmentTable(0x00000012)
{
gmplsOutSegmentDirection = forward (1)
}
Next for the reverse direction:
In gmplsInSegmentTable(0x00000016)
{
gmplsInSegmentDirection = reverse (2)
}
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 7]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
In gmplsOutSegmentTable(0x00000013)
{
gmplsOutSegmentDirection = reverse (2)
}
Next, two cross-connect entries are created in the mplsXCTable of the
MPLS LSR MIB, thereby associating the newly created segments
together.
In mplsXCTable:
{
mplsXCIndex = 0x01,
mplsXCInSegmentIndex = 0x00000015,
mplsXCOutSegmentIndex = 0x00000012,
mplsXCLspId = 0x0102 -- unique ID
mplsXCLabelStackIndex = 0x00, -- only a single
-- outgoing label
mplsXCRowStatus = createAndGo(4)
}
In mplsXCTable:
{
mplsXCIndex = 0x02,
mplsXCInSegmentIndex = 0x00000016,
mplsXCOutSegmentIndex = 0x00000013,
mplsXCLspId = 0x0102 -- unique ID
mplsXCLabelStackIndex = 0x00, -- only a single
-- outgoing label
mplsXCRowStatus = createAndGo(4)
}
Finally, the in-segments and out-segments are activated.
In mplsInSegmentTable(0x00000015):
{
mplsInSegmentRowStatus = active(1)
}
In mplsInSegmentTable(0x00000016):
{
mplsInSegmentRowStatus = active(1)
}
In mplsOutSegmentTable(0x00000012):
{
mplsOutSegmentRowStatus = active(1)
}
In mplsOutSegmentTable(0x00000013):
{
mplsOutSegmentRowStatus = active(1)
}
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 8]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
7. GMPLS Label Switching Router MIB Definitions
GMPLS-LSR-STD-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, zeroDotZero
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
RowPointer
FROM SNMPv2-TC
GmplsSegmentDirection, gmplsStdMIB
FROM GMPLS-TC-STD-MIB
mplsInterfaceIndex, mplsInSegmentIndex, mplsOutSegmentIndex
FROM MPLS-LSR-STD-MIB
;
gmplsLsrStdMIB MODULE-IDENTITY
LAST-UPDATED
"200406010900Z" -- 1 June 2004 9:00:00 GMT
ORGANIZATION
"Common Control And Management Protocols (CCAMP)
Working Group"
CONTACT-INFO
" Thomas D. Nadeau
Cisco Systems, Inc.
Email: tnadeau@cisco.com
Cheenu Srinivasan
Bloomberg L.P.
Email: cheenu@bloomberg.net
Adrian Farrel
Old Dog Consulting
Email: adrian@olddog.co.uk
Ed Harrison
Data Connection Ltd.
Email: ed.harrison@dataconnection.com
Tim Hall
Data Connection Ltd.
Email: tim.hall@dataconnection.com
Comments about this document should be emailed direct to the
CCAMP working group mailing list at ccamp@ops.ietf.org"
DESCRIPTION
"This MIB module contains managed object definitions
for the Generalized Multiprotocol Label Switching
(GMPLS) Router as defined in: Mannie et al.,
Generalized Multi-Protocol Label Switching (GMPLS)
Architecture, draft-ietf-ccamp-gmpls-
architecture-07.txt, May 2003, work in progress.
Copyright (C) The Internet Society (2004). This
version of this MIB module is part of RFCXXX; see
the RFC itself for full legal notices."
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 9]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
-- Revision history.
REVISION
"200406010900Z" -- 1 June 2004 09:00:00 GMT
DESCRIPTION
"Initial revision, published as part of RFC XXXX."
::= { gmplsStdMIB xx }
-- Top level components of this MIB module.
-- Notifications
-- no notifications are currently defined.
gmplsLsrNotifications OBJECT IDENTIFIER ::= { gmplsLsrStdMIB 0 }
-- Tables, Scalars
gmplsLsrObjects OBJECT IDENTIFIER ::= { gmplsLsrStdMIB 1 }
-- Conformance
gmplsLsrConformance OBJECT IDENTIFIER ::= { gmplsLsrStdMIB 2 }
-- GMPLS Interface Table.
gmplsInterfaceTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsInterfaceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies per-interface GMPLS capability
and associated information. It extends the
information in mplsInterfaceTable."
::= { gmplsLsrObjects 1 }
gmplsInterfaceEntry OBJECT-TYPE
SYNTAX GmplsInterfaceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in this table is created
automatically by an LSR for every interface capable
of supporting GMPLS and which is configured to do
so. A conceptual row in this table will exist if and
only if a corresponding entry in mplsInterfaceTable
exists, and a corresponding entry in ifTable exists
with ifType = mpls(166). If the associated entry in
ifTable is operationally disabled (thus removing the
GMPLS capabilities on the interface) or the entry in
mplsInterfaceTable is deleted, the corresponding
entry in this table MUST be deleted shortly
thereafter.
The indexing is the same as that for mplsInterfaceTable.
Thus, the entry with index 0 represents the per-platform
label space and contains parameters that apply to all
interfaces that participate in the per-platform label space."
INDEX { mplsInterfaceIndex }
::= { gmplsInterfaceTable 1 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 10]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
GmplsInterfaceEntry ::= SEQUENCE {
gmplsInterfaceSignalingCaps BITS,
gmplsInterfaceRsvpHelloPeriod Unsigned32
}
gmplsInterfaceSignalingCaps OBJECT-TYPE
SYNTAX BITS {
unknown (0),
rsvpGmpls (1),
crldpGmpls (2), -- note the use of CR-LDP is deprecated
otherGmpls (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Defines the signaling capabilities on this
interface. Multiple bits may legitimately be set at
once. Setting no bits implies that GMPLS signaling
cannot be performed on this interface and all LSPs
must be manually provisioned or that this table
entry is only present to supplement an entry in
the mplsInterfaceTable by providing the information
carried in other objects in this row."
::= { gmplsInterfaceEntry 1 }
gmplsInterfaceRsvpHelloPeriod OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Period, in milliseconds, between sending RSVP Hello
messages on this interface. A value of 0 indicates
that no Hello messages should be sent on this interface."
DEFVAL { 3000 }
::= { gmplsInterfaceEntry 2 }
-- End of gmplsInterfaceTable
-- In-segment table.
gmplsInSegmentTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsInSegmentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table extends the mplsInSegmentTable to provide GMPLS-
specific information about incoming segments to an LSR."
::= { gmplsLsrObjects 2 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 11]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
gmplsInSegmentEntry OBJECT-TYPE
SYNTAX GmplsInSegmentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table extends the representation of
an incoming segment represented by an entry in
mplsInSegmentTable. An entry can be created by a
network administrator or an SNMP agent, or a GMPLS
signaling protocol.
Note that the storage type for this entry SHOULD be
inherited from the corresponding entry in the
mplsInSegmentTable given by the value of the
mplsInSegmentStorageType object."
INDEX { mplsInSegmentIndex }
::= { gmplsInSegmentTable 1 }
GmplsInSegmentEntry ::= SEQUENCE {
gmplsInSegmentDirection GmplsSegmentDirection,
gmplsInSegmentExtraParamsPtr RowPointer
}
gmplsInSegmentDirection OBJECT-TYPE
SYNTAX GmplsSegmentDirection
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the direction of data flow on
this segment. This object cannot be modified if
mplsInSegmentRowStatus for the associated entry in
the mplsInSegmentTable is active(1)."
DEFVAL { forward }
::= { gmplsInSegmentEntry 1 }
gmplsInSegmentExtraParamsPtr OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Some Tunnels will run over transports that can
usefully support technology-specific additional parameters
(for example, SONET resource usage). Such can be supplied from
an external table and referenced from here.
A value of zeroDotzero in this attribute indicates that there
is no such additional information."
DEFVAL { zeroDotZero }
::= { gmplsInSegmentEntry 2 }
-- End of gmplsInSegmentTable
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 12]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
-- Out-segment table.
gmplsOutSegmentTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsOutSegmentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table extends the mplsOutSegmentTable to
provide GMPLS-specific information about outgoing
segments from an LSR."
::= { gmplsLsrObjects 3 }
gmplsOutSegmentEntry OBJECT-TYPE
SYNTAX GmplsOutSegmentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table extends the representation of
an outgoing segment represented by an entry in
mplsOutSegmentTable. An entry can be created by a
network administrator or an SNMP agent, or a GMPLS
signaling protocol.
Note that the storage type for this entry SHOULD be
inherited from the corresponding entry in the
mplsOutSegmentTable given by the value of the
mplsOutSegmentStorageType object."
INDEX { mplsOutSegmentIndex }
::= { gmplsOutSegmentTable 1 }
GmplsOutSegmentEntry ::= SEQUENCE {
gmplsOutSegmentDirection GmplsSegmentDirection,
gmplsOutSegmentTTLDecrement Unsigned32,
gmplsOutSegmentExtraParamsPtr RowPointer
}
gmplsOutSegmentDirection OBJECT-TYPE
SYNTAX GmplsSegmentDirection
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the direction of data flow on
this segment. This object cannot be modified if
mplsOutSegmentRowStatus for the associated entry in
the mplsOutSegmentTable is active(1)."
DEFVAL { forward }
::= { gmplsOutSegmentEntry 1 }
gmplsOutSegmentTTLDecrement OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the amount by which to
decrement the TTL of any payload packets forwarded
on this segment if per-hop decrementing is being
done.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 13]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
A value of zero indicates that no decrement should
be made or that per-hop decrementing is not in
force.
See the gmplsTunnelTTLDecrement object in the
gmplsTunnelTable of [GMPLSTEMIB] for a value by
which to decrement the TTL for the whole of a
tunnel.
This object cannot be modified if
mplsOutSegmentRowStatus for the associated entry in
the mplsOutSegmentTable is active(1)."
DEFVAL { 0 }
::= { gmplsOutSegmentEntry 2 }
gmplsOutSegmentExtraParamsPtr OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Some Tunnels will run over transports that can
usefully support technology-specific additional parameters
(for example, SONET resource usage). Such can be supplied from
an external table and referenced from here.
A value of zeroDotzero in this attribute indicates that there
is no such additional information."
DEFVAL { zeroDotZero }
::= { gmplsOutSegmentEntry 3 }
-- End of gmplsOutSegmentTable
-- Module compliance.
gmplsLsrGroups
OBJECT IDENTIFIER ::= { gmplsLsrConformance 1 }
gmplsLsrCompliances
OBJECT IDENTIFIER ::= { gmplsLsrConformance 2 }
-- Compliance requirement for fully compliant implementations.
gmplsLsrModuleFullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance statement for agents that provide full
support for GMPLS-LSR-STD-MIB."
MODULE IF-MIB -- The Interfaces Group MIB, RFC 2863.
MANDATORY-GROUPS {
ifGeneralInformationGroup,
ifCounterDiscontinuityGroup
}
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 14]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
MODULE MPLS-LSR-STD-MIB -- The MPLS LSR MIB
MANDATORY-GROUPS {
mplsInterfaceGroup,
mplsInSegmentGroup,
mplsOutSegmentGroup,
mplsXCGroup,
mplsPerfGroup,
mplsLsrNotificationGroup
}
MODULE -- this module
MANDATORY-GROUPS {
gmplsInterfaceGroup,
gmplsInSegmentGroup,
gmplsOutSegmentGroup
}
-- gmplsInSegmentTable
OBJECT gmplsInSegmentDirection
SYNTAX GmplsSegmentDirection
MIN-ACCESS read-write
DESCRIPTION
"Only forward(1) needs to be supported by
implementations that only support unidirectional
LSPs."
-- gmplsOutSegmentTable
OBJECT gmplsOutSegmentDirection
SYNTAX GmplsSegmentDirection
MIN-ACCESS read-write
DESCRIPTION
"Only forward(1) needs to be supported by
implementations that only support unidirectional
LSPs."
OBJECT gmplsOutSegmentTTLDecrement
SYNTAX Unsigned32 (0..255)
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { gmplsLsrCompliances 1 }
-- Compliance requirement for implementations that provide read-only
-- access.
gmplsLsrModuleReadOnlyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance requirement for implementations that only
provide read-only support for GMPLS-LSR-STD-MIB. Such
devices can then be monitored but cannot be configured
using this MIB modules."
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 15]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
MODULE IF-MIB -- The interfaces Group MIB, RFC 2863
MANDATORY-GROUPS {
ifGeneralInformationGroup,
ifCounterDiscontinuityGroup
}
MODULE MPLS-LSR-STD-MIB
MANDATORY-GROUPS {
mplsInterfaceGroup,
mplsInSegmentGroup,
mplsOutSegmentGroup,
mplsXCGroup,
mplsPerfGroup
}
MODULE -- this module
MANDATORY-GROUPS {
gmplsInterfaceGroup,
gmplsInSegmentGroup,
gmplsOutSegmentGroup
}
-- gmplsInterfaceGroup
OBJECT gmplsInterfaceSignalingCaps
SYNTAX BITS {
unknown (0),
rsvpGmpls (1),
crldpGmpls (2),
otherGmpls (3)
}
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsInterfaceRsvpHelloPeriod
SYNTAX Unsigned32
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
-- gmplsInSegmentTable
OBJECT gmplsInSegmentDirection
SYNTAX GmplsSegmentDirection
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. Only forward(1) needs
to be supported by implementations that only support
unidirectional LSPs."
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 16]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
OBJECT gmplsInSegmentExtraParamsPtr
SYNTAX RowPointer
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
-- gmplsOutSegmentTable
OBJECT gmplsOutSegmentDirection
SYNTAX GmplsSegmentDirection
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. Only forward(1) needs
to be supported by implementations that only support
unidirectional LSPs."
OBJECT gmplsOutSegmentTTLDecrement
SYNTAX Unsigned32 (0..255)
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsOutSegmentExtraParamsPtr
SYNTAX RowPointer
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { gmplsLsrCompliances 2 }
-- Units of conformance.
gmplsInterfaceGroup OBJECT-GROUP
OBJECTS {
gmplsInterfaceSignalingCaps,
gmplsInterfaceRsvpHelloPeriod
}
STATUS current
DESCRIPTION
"Collection of objects needed for GMPLS interface
configuration and performance information."
::= { gmplsLsrGroups 1 }
gmplsInSegmentGroup OBJECT-GROUP
OBJECTS {
gmplsInSegmentDirection,
gmplsInSegmentExtraParamsPtr
}
STATUS current
DESCRIPTION
"Collection of objects needed to implement a GMPLS
in-segment."
::= { gmplsLsrGroups 2 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 17]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
gmplsOutSegmentGroup OBJECT-GROUP
OBJECTS {
gmplsOutSegmentDirection,
gmplsOutSegmentTTLDecrement,
gmplsOutSegmentExtraParamsPtr
}
STATUS current
DESCRIPTION
"Collection of objects needed to implement a GMPLS
out-segment."
::= { gmplsLsrGroups 3 }
END
8. GMPLS Label MIB Definitions
GMPLS-LABEL-STD-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Unsigned32,
Integer32
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
RowStatus, StorageType
FROM SNMPv2-TC
InterfaceIndexOrZero
FROM IF-MIB
IndexIntegerNextFree
FROM DIFFSERV-MIB
MplsLabel
FROM MPLS-TC-STD-MIB
GmplsGeneralizedLabelTypes, GmplsFreeformLabel,
gmplsStdMIB
FROM GMPLS-TC-STD-MIB
;
gmplsLabelStdMIB MODULE-IDENTITY
LAST-UPDATED
"200406010900Z" -- 1 June 2004 9:00:00 GMT
ORGANIZATION
"Common Control And Management Protocols (CCAMP)
Working Group"
CONTACT-INFO
" Thomas D. Nadeau
Cisco Systems, Inc.
Email: tnadeau@cisco.com
Cheenu Srinivasan
Bloomberg L.P.
Email: cheenu@bloomberg.net
Adrian Farrel
Old Dog Consulting
Email: adrian@olddog.co.uk
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 18]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
Ed Harrison
Data Connection Ltd.
Email: ed.harrison@dataconnection.com
Tim Hall
Data Connection Ltd.
Email: tim.hall@dataconnection.com
Comments about this document should be emailed direct to the
CCAMP working group mailing list at ccamp@ops.ietf.org"
DESCRIPTION
"This MIB module contains managed object definitions
for labels within GMPLS systems."
-- Revision history.
REVISION
"200406010900Z" -- 1 June 2004 09:00:00 GMT
DESCRIPTION
"Initial revision, published as part of RFC XXXX."
::= { gmplsStdMIB xx }
-- Top level components of this MIB module.
-- Notifications
-- no notifications are currently defined.
gmplsLabelNotifications OBJECT IDENTIFIER ::= { gmplsLabelStdMIB 0 =
}
-- Tables, Scalars
gmplsLabelObjects OBJECT IDENTIFIER ::= { gmplsLabelStdMIB 1 =
}
-- Conformance
gmplsLabelConformance OBJECT IDENTIFIER ::= { gmplsLabelStdMIB 2 =
}
-- GMPLS Label Table.
gmplsLabelIndexNext OBJECT-TYPE
SYNTAX IndexIntegerNextFree
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains an unused value for
gmplsLabelIndex, or a zero to indicate
that no unused value exists or is available.
An management application wishing to create
a row in the gmplsLabelTable may read this
object and then attempt to create a row in
the table. If row creation fails (because
another application has already created a row
with the supplied index) the management
application should read this object again
to get a new index value.
When a row is created in the gmplsLabelTable
with the gmplsLabelIndex value held by this
object, an implementation MUST change the value
in this object."
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 19]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
::= { gmplsLabelObjects 1 }
gmplsLabelTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsLabelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of GMPLS Labels. This table allows the representation
of the more complex label forms required for GMPLS which
cannot be held within the textual convention MplsLabel. That
is labels that cannot be encoded within 32 bits. It is,
nevertheless also capable of holding 32 bit labels or
regular MPLS labels if desired.
Each entry in this table represents an individual
GMPLS label value. Labels in the tables in other
MIBs are referred to using row pointer into this
table. The indexing of this table provides for
arbitrary indexing and also for concatenation of
labels."
::= { gmplsLabelObjects 2 }
gmplsLabelEntry OBJECT-TYPE
SYNTAX GmplsLabelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents a single label
value. There are three indexes into the table.
- The interface index may be helpful to distinguish
which labels are in use on which interfaces or to
handle cases where there are a very large number
of labels in use in the system. When label
representation is desired to apply to the whole
system or when it is not important to distinguish
labels by their interfaces, this index MAY be set
to zero.
- The label index provides a way of identifying the
label.
- The label sub-index is only used for concatenated
labels. It identifies each component label. When
non-concatenated labels are used, this index
SHOULD be set to zero.
A storage type object is supplied to control the
storage type for each entry, but implementations
should note that the storage type of conceptual rows
in other tables that include row pointers to an
entry in this table SHOULD dictate the storage type
of the rows in this table where the row in the other
table is more persistent."
INDEX {
gmplsLabelInterface,
gmplsLabelIndex,
gmplsLabelSubindex }
::= { gmplsLabelTable 1 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 20]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
GmplsLabelEntry ::= SEQUENCE {
gmplsLabelInterface InterfaceIndexOrZero,
gmplsLabelIndex Unsigned32,
gmplsLabelSubindex Unsigned32,
gmplsLabelType GmplsGeneralizedLabelTypes,
gmplsLabelMplsLabel MplsLabel,
gmplsLabelPortWavelength Unsigned32,
gmplsLabelFreeform GmplsFreeformLabel,
gmplsLabelSonetSdhSignalIndex Integer32,
gmplsLabelSdhVc Integer32,
gmplsLabelSdhVcBranch Integer32,
gmplsLabelSonetSdhBranch Integer32,
gmplsLabelSonetSdhGroupBranch Integer32,
gmplsLabelWavebandId Unsigned32,
gmplsLabelWavebandStart Unsigned32,
gmplsLabelWavebandEnd Unsigned32,
gmplsLabelRowStatus RowStatus,
gmplsLabelStorageType StorageType
}
gmplsLabelInterface OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interface on which this label is used. If the
label has or could have applicability across the
whole system, this object SHOULD be set to zero."
::= { gmplsLabelEntry 1 }
gmplsLabelIndex OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An arbitrary index into the table to identify a label.
Note that implementations that are representing 32 bit
labels within this table MAY choose to align this index
with the value of the label, but should be aware of the
implications of sparsely populated tables.
A management application may read the gmplsLabelIndexNext
object to find a suitable value for this object."
::= { gmplsLabelEntry 2 }
gmplsLabelSubindex OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"In conjunction with gmplsLabelInterface and gmplsLabelIndex,
this object uniquely identifies this row. This sub-index
allows a single GMPLS label to be defined as a concatenation
of labels. This is particularly useful in TDM.
The ordering of sub-labels is strict with the sub-label with
lowest gmplsLabelSubindex appearing first. Note that all sub-
labels of a single GMPLS label must share the same
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 21]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
gmplsLabelInterface and gmplsLabelIndex values. For labels
that are not composed of concatenated sub-labels, this value
SHOULD be set to zero."
::= { gmplsLabelEntry 3 }
gmplsLabelType OBJECT-TYPE
SYNTAX GmplsGeneralizedLabelTypes
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Identifies the type of this label. Note that this object
does not determine whether MPLS or GMPLS signaling is in
use: a value of gmplsMplsLabel (1) denotes that a 23 bit
MPLS packet label is present, but does not describe
whether this is signaled using MPLS or GMPLS.
The value of this object helps determine which of
the following objects are valid.
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
::= { gmplsLabelEntry 4 }
gmplsLabelMplsLabel OBJECT-TYPE
SYNTAX MplsLabel
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of an MPLS label (that is a packet label)
if this table is used to store it. This may be used
in MPLS systems even though the label values can be
adequately stored in the MPLS MIB modules. Further,
in mixed MPLS and GMPLS systems it may be
advantageous to store all labels in a single label
table. Lastly, in GMPLS systems where packet labels
are used (that is in systems that use GMPLS
signaling and GMPLS labels for packet switching) it
may be desirable to use this table.
This object is only valid if gmplsLabelType is set
to gmplsMplsLabel (1).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
DEFVAL { 0 }
::= { gmplsLabelEntry 6 }
gmplsLabelPortWavelength OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of a Port or Wavelength Label when carried
as a Generalized Label. Only valid if gmplsLabelType
is set to gmplsPortWavelengthLabel(2).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
DEFVAL { 0 }
::= { gmplsLabelEntry 7 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 22]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
gmplsLabelFreeform OBJECT-TYPE
SYNTAX GmplsFreeformLabel
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of a freeform Generalized Label that does
not conform to one of the standardized label
encoding or that an implementation chooses to
represent as an octet string without further
decoding. Only valid if
gmplsLabelType is set to
gmplsFreeformGeneralizedLabel(3).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
::= { gmplsLabelEntry 8 }
gmplsLabelSonetSdhSignalIndex OBJECT-TYPE
SYNTAX Integer32 (0..4095)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Signal Index value (S) of a SONET or SDH
Generalized Label. Zero indicates that this field is
not significant. Only valid if gmplsLabelType is set
to gmplsSonetLabel(4) or gmplsSdhLabel(5).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
DEFVAL { 0 }
::= { gmplsLabelEntry 9 }
gmplsLabelSdhVc OBJECT-TYPE
SYNTAX Integer32 (0..15)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The VC Indicator (U) of an SDH Generalized Label.
Zero indicates that this field is non-significant.
Only valid if gmplsLabelType is set to
gmplsSdhLabel(5).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
DEFVAL { 0 }
::= { gmplsLabelEntry 10 }
gmplsLabelSdhVcBranch OBJECT-TYPE
SYNTAX Integer32 (0..15)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The VC Branch Indicator (K) of an SDH Generalized
Label. Zero indicates that this field is non-
significant. Only valid if gmplsLabelType is set to
gmplsSdhLabel(5).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
DEFVAL { 0 }
::= { gmplsLabelEntry 11 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 23]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
gmplsLabelSonetSdhBranch OBJECT-TYPE
SYNTAX Integer32 (0..15)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Branch Indicator (L) of a SONET or SDH
Generalized Label. Zero indicates that this field is
non-significant. Only valid gmplsLabelType is set to
gmplsSonetLabel(4) or gmplsSdhLabel(5).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
DEFVAL { 0 }
::= { gmplsLabelEntry 12 }
gmplsLabelSonetSdhGroupBranch OBJECT-TYPE
SYNTAX Integer32 (0..15)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Group Branch Indicator (M) of a SONET or SDH
Generalized Label. Zero indicates that this field is
non-significant. Only valid if gmplsLabelType is set
to gmplsSonetLabel(4) or gmplsSdhLabel(5).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
DEFVAL { 0 }
::= { gmplsLabelEntry 13 }
gmplsLabelWavebandId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The waveband identifier component of a waveband
label. Only valid if gmplsLabelType is set to
gmplsWavebandLabel(6).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
DEFVAL { 0 }
::= { gmplsLabelEntry 14 }
gmplsLabelWavebandStart OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The starting label component of a waveband label.
Only valid if gmplsLabelType is set to
gmplsWavebandLabel(6).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
DEFVAL { 0 }
::= { gmplsLabelEntry 15 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 24]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
gmplsLabelWavebandEnd OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The end label component of a waveband label. Only
valid if gmplsLabelType is set to
gmplsWavebandLabel(6).
This object cannot be modified if
gmplsLabelRowStatus is active(1)."
DEFVAL { 0 }
::= { gmplsLabelEntry 16 }
gmplsLabelRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable is used to create, modify, and/or
delete a row in this table. When a row in this
table has a row in the active(1) state, no
objects in this row can be modified except the
gmplsLabelRowStatus and gmplsLabelStorageType."
::= { gmplsLabelEntry 17 }
gmplsLabelStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable indicates the storage type for this
object.
The agent MUST ensure that this object's value
remains consistent with the storage type of any rows
in other tables that contain pointers to this row.
In particular, the storage type of this row must be
at least as permanent as that of any row that point
to it.
Conceptual rows having the value 'permanent' need
not allow write-access to any columnar objects in
the row."
REFERENCE
"See RFC2579."
DEFVAL { volatile }
::= { gmplsLabelEntry 18 }
-- End of GMPLS Label Table
-- Module compliance.
gmplsLabelGroups
OBJECT IDENTIFIER ::= { gmplsLabelConformance 1 }
gmplsLabelCompliances
OBJECT IDENTIFIER ::= { gmplsLabelConformance 2 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 25]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
gmplsLabelModuleFullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance statement for agents that support
the GMPLS Label MIB module."
MODULE -- this module
-- The mandatory groups have to be implemented by LSRs claiming
-- support for this MIB module. This MIB module is, however, not
-- mandatory for a working implementation of a GMPLS LSR with full
-- MIB support if the GMPLS labels in use can be represented within
-- a 32 bit quantity.
MANDATORY-GROUPS {
gmplsLabelTableGroup
}
-- Units of conformance.
GROUP gmplsLabelTableGroup
DESCRIPTION
"This group is mandatory for devices which support
the gmplsLabelTable."
GROUP gmplsLabelPacketGroup
DESCRIPTION
"This group extends gmplsLabelTableGroup for
implementations that support packet labels."
GROUP gmplsLabelPortWavelengthGroup
DESCRIPTION
"This group extends gmplsLabelTableGroup for
implementations that support port and wavelength
labels."
GROUP gmplsLabelFreeformGroup
DESCRIPTION
"This group extends gmplsLabelTableGroup for
implementations that support freeform labels."
GROUP gmplsLabelSonetSdhGroup
DESCRIPTION
"This group extends gmplsLabelTableGroup for
implementations that support SONET or SDH labels."
GROUP gmplsLabelWavebandGroup
DESCRIPTION
"This group extends gmplsLabelTableGroup for
implementations that support Waveband labels."
-- gmplsLabelTable
OBJECT gmplsLabelType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 26]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
OBJECT gmplsLabelMplsLabel
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelPortWavelength
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelFreeform
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelSonetSdhSignalIndex
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelSdhVc
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelSdhVcBranch
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelSonetSdhBranch
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelSonetSdhGroupBranch
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelWavebandId
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 27]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
OBJECT gmplsLabelWavebandStart
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelWavebandEnd
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsLabelRowStatus
SYNTAX RowStatus {
active(1),
notInService(2)
}
WRITE-SYNTAX RowStatus {
active(1),
notInService(2),
createAndGo(4),
destroy(6)
}
DESCRIPTION
"Support for notInService, createAndWait and notReady
is not required."
OBJECT gmplsLabelStorageType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { gmplsLabelCompliances 1 }
-- Units of conformance.
gmplsLabelTableGroup OBJECT-GROUP
OBJECTS {
gmplsLabelIndexNext,
gmplsLabelType,
gmplsLabelRowStatus,
gmplsLabelStorageType
}
STATUS current
DESCRIPTION
"Necessary, but not sufficient, set of objects to
implement label table support. In addition,
depending on the type of labels supported (for
example, wavelength labels), the following other
groups defined below are mandatory:
gmplsLabelPacketGroup and/or
gmplsLabelPortWavelengthGroup and/or
gmplsLabelFreeformGroup and/or
gmplsLabelSonetSdhGroup."
::= { gmplsLabelGroups 1 }
gmplsLabelPacketGroup OBJECT-GROUP
OBJECTS {
gmplsLabelMplsLabel
}
STATUS current
DESCRIPTION
"Object needed to implement Packet (MPLS) labels."
::= { gmplsLabelGroups 2 }
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 28]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
gmplsLabelPortWavelengthGroup OBJECT-GROUP
OBJECTS {
gmplsLabelPortWavelength
}
STATUS current
DESCRIPTION
"Object needed to implement Port and Wavelength
labels."
::= { gmplsLabelGroups 3 }
gmplsLabelFreeformGroup OBJECT-GROUP
OBJECTS {
gmplsLabelFreeform
}
STATUS current
DESCRIPTION
"Object needed to implement Freeform labels."
::= { gmplsLabelGroups 4 }
gmplsLabelSonetSdhGroup OBJECT-GROUP
OBJECTS {
gmplsLabelSonetSdhSignalIndex,
gmplsLabelSdhVc,
gmplsLabelSdhVcBranch,
gmplsLabelSonetSdhBranch,
gmplsLabelSonetSdhGroupBranch
}
STATUS current
DESCRIPTION
"Object needed to implement SONET and SDH labels."
::= { gmplsLabelGroups 5 }
gmplsLabelWavebandGroup OBJECT-GROUP
OBJECTS {
gmplsLabelWavebandId,
gmplsLabelWavebandStart,
gmplsLabelWavebandEnd
}
STATUS current
DESCRIPTION
"Object needed to implement Waveband labels."
::= { gmplsLabelGroups 6 }
END
9. Security Considerations
It is clear that the MIB modules described in this document in
association with the MPLS-LSR-STD-MIB are potentially useful for
monitoring of GMPLS LSRs. These MIB modules can also be used for
configuration of certain objects, and anything that can be configured
can be incorrectly configured, with potentially disastrous results.
There are a number of management objects defined in these MIB modules
with a MAX-ACCESS clause of read-write and/or read-create. Such
objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 29]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
environment without proper protection can have a negative effect on
network operations. These are the tables and objects and their
sensitivity/vulnerability:
o the gmplsInterfaceTable, gmplsInSegmentTable, gmplsOutSegmentTable
and gmplsLabelTable collectively contain objects to provision
GMPLS interfaces, LSPs and their associated parameters on a Label
Switching Router (LSR). Unauthorized write access to objects in
these tables, could result in disruption of traffic on the
network. This is especially true if an LSP has already been
established. The use of stronger mechanisms such as SNMPv3
security should be considered where possible. Specifically, SNMPv3
VACM and USM MUST be used with any SNMPv3 agent which implements
these MIB modules.
Some of the readable objects in these MIB modules "i.e., objects with
a MAX-ACCESS other than not-accessible" may be considered sensitive
or vulnerable in some network environments. It is thus important to
control even GET and/or NOTIFY access to these objects and possibly
to even encrypt the values of these objects when sending them over
the network via SNMP. These are the tables and objects and their
sensitivity/vulnerability:
o the gmplsInterfaceTable, gmplsInSegmentTable, gmplsOutSegmentTable
and gmplsLabelTable collectively show the LSP network topology and
its capabilities. If an Administrator does not want to reveal this
information, then these tables should be considered
sensitive/vulnerable.
SNMP versions prior to SNMPv3 did not include adequate security. Even
if the network itself is secure "for example by using IPSec", even
then, there is no control as to who on the secure network is allowed
to access and GET/SET "read/change/create/delete" the objects in
these MIB modules. It is RECOMMENDED that implementers consider the
security features as provided by the SNMPv3 framework "see [RFC3410],
section 8", including full support for the SNMPv3 cryptographic
mechanisms "for authentication and privacy".
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module, is properly configured to give access to
the objects only to those principals "users" that have legitimate
rights to indeed GET or SET "change/create/delete" them.
10. Acknowledgments
This document extends [LSRMIB]. The authors would like to express
their gratitude to all those who worked on that earlier MIB document.
The authors would like to express their thanks to Dan Joyle for his
careful review and comments on early versions of the Label Table.
Special thanks to Joan Cucchiara and Len Nieman for their help with
compilation issues.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 30]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
11. IANA Considerations
MPLS related standards track MIB modules are rooted under the
mplsStdMIB subtree.
One of the MIB modules contained in this document extends tables
contained in MPLS MIB modules.
As requested in requested in the GMPLS-TC-STD-MIB [GMPLSTCMIB] the
two MIB modules contained in this document should be placed in the
mplsStdMIB subtree as well.
New assignments can only be made via a Standards Action as specified
in [RFC2434].
11.1. IANA Considerations for GMPLS-LSR-STD-MIB
The IANA is requested to assign { mplsStdMIB xx } to the
GMPLS-LSR-STD-MIB module specified in this document.
11.2. IANA Considerations for GMPLS-LABEL-STD-MIB
The IANA is requested to assign { mplsStdMIB xx } to the
GMPLS-LABEL-STD-MIB module specified in this document.
12. References
12.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J.,
Case, J., Rose, M., and S. Waldbusser, "Structure
of Management Information Version 2 (SMIv2)", STD
58, RFC 2578, April 1999.
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J.,
Case, J., Rose, M., and S. Waldbusser, "Textual
Conventions for SMIv2", STD 58, RFC 2579, April
1999.
[RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J.,
Case, J., Rose, M., and S. Waldbusser, "Conformance
Statements for SMIv2", STD 58, RFC 2580, April
1999.
[RFC2863] McCloghrie, K. and F. Kastenholtz, "The Interfaces
Group MIB", RFC 2863, June 2000.
[GMPLSArch] Mannie, E. (Editor), "Generalized Multiprotocol
Label Switching (GMPLS) Architecture",
draft-many-gmpls-architecture-07.txt, May
2003, work in progress.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 31]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
[GMPLSSonetSDH] Mannie, E., Papadimitriou, D. (Editors),
"Generalized Multi-Protocol Label Switching
Extensions for SONET and SDH Control",
draft-ietf-ccamp-gmpls-sonet-sdh-08.txt,
February 2003, work in progress.
[GMPLSTCMIB] Nadeau, T., Srinivasan, C., Farrel, A., Hall, T.,
and Harrison, E., "Definitions of Textual
Conventions for Multiprotocol Label Switching
(MPLS) Management", draft-ietf-ccamp-gmpls-te-mib-
05.txt, June 2004, work in progress.
[GMPLSTEMIB] Nadeau, T., Srinivasan, C., Farrel, A., Hall, T.,
and Harrison, E., "Generalized Multiprotocol Label
Switching (GMPLS) Traffic Engineering Management
Information Base", draft-ietf-ccamp-gmpls-te-mib-
05.txt, June 2004, work in progress.
[TCMIB] Nadeau, T., Cucchiara, J. (Editors) "Definitions of
Textual Conventions for Multiprotocol Label
Switching (MPLS) Management", draft-ietf-mpls-tc-
mib-10.txt, November 2003, work in progress.
[LSRMIB] Srinivasan, C., Viswanathan, A. and T. Nadeau,
"Multiprotocol Label Switching (MPLS) Label
Switching Router (LSR) Management Information
Base", draft-ietf-mpls-lsr-mib-14.txt, November
2003, work in progress.
12.2. Informational References
[RFC2026] S. Bradner, "The Internet Standards Process --
Revision 3", RFC 2026, October 1996.
[RFC2434] Narten, T. and H. Alvestrand, "Guidelines for
Writing an IANA Considerations Section in RFCs",
BCP: 26, RFC 2434, October 1998.
[RFC3031] Rosen, E., Viswanathan, A., and R. Callon,
"Multiprotocol Label Switching Architecture", RFC
3031, January 2001.
[RFC3209] Awduche, D., Berger, L., Gan, D., Li, T.,
Srinivasan, V., and G. Swallow, "RSVP-TE:
Extensions to RSVP for LSP Tunnels", RFC 3209,
December 2001.
[RFC3212] Jamoussi, B., Aboul-Magd, O., Andersson, L.,
Ashwood-Smith, P., Hellstrand, F., Sundell, K.,
Callon, R., Dantu, R., Wu, L., Doolan, P., Worster,
T., Feldman, N., Fredette, A., Girish, M., Gray,
E., Halpern, J., Heinanen, J., Kilty, T., Malis,
A., and P. Vaananen, "Constraint-Based LSP Setup
using LDP", RFC 3212, December 2001."
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 32]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
[RFC3410] Case, J., Mundy, R., Partain, D. and B. Stewart,
"Introduction and Applicability Statements for
Internet-Standard Management Framework", RFC 3410,
December 2002.
[RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An
Architecture for Describing Simple Network
Management Protocol (SNMP) Management Frameworks",
RFC 3411, December 2002.
[RFC3413] Levi, D., Meyer, P., Stewart, B., "SNMP
Applications", RFC 3413, December 2002.
[RFC3471] Berger, L. (Editor), "Generalized Multi-Protocol
Label Switching (GMPLS) Signaling Functional
Description", RFC 3471, January 2003.
[RFC3472] Ashwood-Smith, P., Berger, L. (Editors),
"Generalized MPLS Signaling - CR-LDP Extensions",
RFC 3472, January 2003.
[RFC3473] Berger, L. (Editor), "Generalized MPLS Signaling -
RSVP-TE Extensions", RFC 3473 January 2003.
[TEMIB] Nadeau, T., Srinivasan, C, Viswanathan, A.,
"Multiprotocol Label Switching (MPLS) Traffic
Engineering Management Information Base",
draft-ietf-mpls-te-mib-14.txt, November 2003,
work in progress.
13. Authors' Addresses
Thomas D. Nadeau
Cisco Systems, Inc.
300 Apollo Drive
Chelmsford, MA 01824
Phone: +1-978-244-3051
Email: tnadeau@cisco.com
Cheenu Srinivasan
Bloomberg L.P.
499 Park Ave.,
New York, NY 10022
Phone: +1-212-893-3682
Email: cheenu@bloomberg.net
Adrian Farrel
Old Dog Consulting
Phone: +44-(0)-1978-860944
Email: adrian@olddog.co.uk
Tim Hall
Data Connection Ltd.
100 Church Street
Enfield, Middlesex, EN2 6BQ, UK
Phone: +44 20 8366 1177
Email: tim.hall@dataconnection.com
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 33]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
Ed Harrison
Data Connection Ltd.
100 Church Street
Enfield, Middlesex, EN2 6BQ, UK
Phone: +44 20 8366 1177
Email: ed.harrison@dataconnection.com
14. Intellectual Property Considerations
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
14.1. IPR Disclosure Acknowledgement
By submitting this Internet-Draft, I certify that any applicable
patent or other IPR claims of which I am aware have been disclosed,
and any of which I become aware will be disclosed, in accordance with
RFC 3668.
15. Full Copyright Statement
Copyright (C) The Internet Society (2004). This document is subject
to the rights, licenses and restrictions contained in BCP 78, and
except as set forth therein, the authors retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 34]
Internet Draft draft-ietf-ccamp-gmpls-lsr-mib-05.txt June 2004
16. Changes and Pending Work
This section must be removed before the draft progresses to RFC.
16.1. Pending Work
The following work items have been identified for this draft. They
will be addressed in a future version.
- Expand conformance statements to give one for monitoring only,
and one for monitoring and control.
- Determine whether the 'discriminated union' in the Label Table is
good MIB.
16.2. Changes from version 4 to version 5
- New IPR and copyright boiler plate.
- Clarify description of gmplsInterfaceSignalingCaps.
16.3. Changes from version 3 to version 4
- Update references.
- Allow configuration of the Hello timer per interface.
- Provide support for monitoring technology-specific resources or
performance through an arbitrary row pointer.
- Retire unnecessary gmplsLabelFreeformLength.
- Update examples.
16.4. Changes from version 2 to version 3
- Work on basic compilation issues.
- Provide a next index object to supply the next available
arbitrary index into the Label Table.
- Update references.
- Update examples.
Nadeau, Srinivasan, Farrel, Hall and Harrison [Page 35]
| PAFTECH AB 2003-2026 | 2026-04-23 01:34:25 |