One document matched: draft-ietf-bmwg-acc-bench-term-01.txt
Differences from draft-ietf-bmwg-acc-bench-term-00.txt
Network Working Group
INTERNET-DRAFT
Expires in: April 2004
Scott Poretsky
Quarry Technologies
Shankar Rao
Qwest Communications
Ray Piatt
Cable and Wireless
October 2003
Terminology for Accelerated Stress Benchmarking
<draft-ietf-bmwg-acc-bench-term-01.txt>
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other
documents at any time. It is inappropriate to use Internet-Drafts
as reference material or to cite them other than as "work in
progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
ABSTRACT
This terminology document provides the terms to be used for
benchmarking a router or switch under Accelerated Stress conditions.
Terminology is provided for performing this benchmark using
the Contol Plane, Data Plane, Management Plane, and Security
Plane of the Device Under Test. Terms are defined for
Configuration, Startup Conditions, Instability Conditions, Failure
Conditions, and Benchmarks.
Poretsky, Rao, Piatt [Page 1]
INTERNET-DRAFT Terminology for Accelerated Stress Benchmarking October 2003
Table of Contents
1. Introduction ............................................... 3
2. Existing definitions ....................................... 3
3. Term definitions............................................ 3
3.1 Benchmark Planes.......................................... 3
3.1.1 Control Plane........................................... 4
3.1.2 Data Plane.............................................. 5
3.1.3 Management Plane........................................ 5
3.1.4 Security Plane.......................................... 6
3.2 Configuration Sets........................................ 6
3.2.1 Control Plane Configuration Set......................... 7
3.2.2 Data Plane Configuration Set............................ 7
3.2.2.1 Traffic Profile....................................... 8
3.2.3 Management Plane Configuration Set...................... 8
3.2.4 Security Plane Configuration Set........................ 9
3.3 Startup Conditions........................................10
3.3.1 Control Plane Startup Conditions........................10
3.3.2 Security Plane Startup Conditions.......................11
3.4 Instability Conditions....................................11
3.4.1 Control Plane Instability Conditions....................12
3.4.2 Data Plane Instability Conditions.......................12
3.4.3 Management Plane Instability Conditions.................13
3.4.4 Security Plane Instability Conditions...................13
3.5 Failure Conditions........................................14
3.5.1 Unexpected Packet Loss..................................14
3.5.2 Unexpected Session Loss.................................14
3.5.3 Misrouted Packets.......................................15
3.5.4 Access Denial...........................................15
3.5.5 Errored Management Value................................16
3.5.6 Security Plane Failure..................................16
3.6 Benchmarks................................................17
3.6.1 Success Threshold.......................................17
3.6.2 Accelerated-Life Test Duration..........................17
4. Security Considerations.....................................18
5. References..................................................18
6. Author's Address............................................18
7. Full Copyright Statement....................................19
Appendix 1 - White Box Benchmarks..............................20
Poretsky, Rao, Piatt [Page 2]
INTERNET-DRAFT Terminology for Accelerated Stress Benchmarking October 2003
1. Introduction
Routers in an operational network are simultaneously configured with
multiple protocols and security policies while forwarding traffic and
being managed. To accurately benchmark a router for deployment it is
necessary to test that router in operational conditions by
simultaneously configuring and scaling network protocols and security
policies, forwarding traffic, and managing the device. It is helpful
to accelerate these network operational conditions so that the
router under test can be benchmarked with faster test duration.
Testing a router in accelerated network conditions is known as
Accelerated Stress Testing.
This document defines the Benchmark Planes used for the Accelerated
Life Benchmarking. These are the Control Plane, Data Plane,
Management Plane, and Security Plane. For each plane, the
Configuration Set, Startup Conditions, and Instability Conditions.
Terms are also defined for observing Failure Conditions and reporting
Benchmarks. White Box benchmarks are provided in Appendix 1 for
additional DUT behavior measurements.
2. Existing definitions
RFC 1242 "Benchmarking Terminology for Network Interconnect
Devices" and RFC 2285 "Benchmarking Terminology for LAN Switching
Devices" should be consulted before attempting to make use of this
document.
For the sake of clarity and continuity this RFC adopts the template
for definitions set out in Section 2 of RFC 1242. Definitions are
indexed and grouped together in sections for ease of reference.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in
this document are to be interpreted as described in RFC 2119.
3. Term definitions
3.1 Benchmark Planes
Definition:
The features, conditions, and behavior for the Accelerated Stress
Benchmarking.
Discussion:
There are four Benchmark Planes: Control Plane, Data Plane,
Management Plane, and Security Plane as shown in Figure 1. The
Benchmark Planes define the Configuration, Startup Conditions,
Instability Conditions, and Failure Conditions used for the test.
Poretsky, Rao, Piatt [Page 3]
INTERNET-DRAFT Terminology for Accelerated Stress Benchmarking October 2003
___________ ___________
| Control | | Management|
| Plane |___ ___| Plane |
| | | | | |
----------- | | -----------
\/ \/ ___________
___________ | Security |
| |<-----------| Plane |
| DUT | | |
|--->| |<---| -----------
| ----------- |
| |
| ___________ |
| | Data | |
|--->| Plane |<---|
| |
-----------
Figure 1. Router Accelerated Stress Benchmarking Planes
Measurement units: N/A
Issues: None
See Also:
Control Plane
Data Plane
Management Plane
Security Plane
3.1.1 Control Plane
Definition:
The Description of the control protocols enabled for
the Accelerated Stress Benchmarking.
Discussion:
The Control Plane defines the Configuration, Startup
Conditions, Instability Conditions, and Failure
Conditions of the control protocols used for the test.
Control Plane protocols may include routing protocols,
multicast protocols, and MPLS protocols. These can be
enabled or disabled for a benchmark test.
Measurement units: N/A
Issues: None
See Also:
Benchmark Planes
Control Plane Configuration Set
Control Plane Startup Conditions
Control Plane Instability Conditions
Control Plane Failure Conditions
Poretsky, Rao, Piatt [Page 4]
INTERNET-DRAFT Terminology for Accelerated Stress Benchmarking October 2003
3.1.2 Data Plane
Definition:
The data traffic profile used for the Accelerated Stress
Benchmarking.
Discussion:
The Data Plane defines the Configuration, Startup
Conditions, Instability Conditions, and Failure
Conditions of the data traffic used for the test.
The Data Plane includes the traffic and interface
profile.
Measurement Units:
N/A
See Also:
Benchmark Planes
Data Plane Configuration Set
Data Plane Startup Conditions
Data Plane Instability Conditions
Data Plane Failure Conditions
3.1.3 Management Plane
Definition:
The Management features and tools used for the
Accelerated Stress Benchmarking.
Discussion:
A key component of the Accelerated Stress Benchmarking is the
Management Plane to assess manageability of the router
under stress. The Management Plane defines the Configuration,
Startup Conditions, Instability Conditions, and Failure
Conditions of the management protocols and features used for
the test. The Management Plane includes SNMP, Logging/Debug,
and Statistics Collection.
Measurement units:
N/A
Issues:
None
See Also:
Benchmark Planes
Management Plane Configuration Set
Management Plane Startup Conditions
Management Plane Instability Conditions
Management Plane Failure Conditions
Poretsky, Rao, Piatt [Page 5]
INTERNET-DRAFT Terminology for Accelerated Stress Benchmarking October 2003
3.1.4 Security Plane
Definition:
The Security features used during the Accelerated Stress
Benchmarking.
Discussion:
The Control Plane defines the Configuration, Startup
Conditions, Instability Conditions, and Failure
Conditions of the security features and protocols used for
the test. The Security Plane includes the ACLs, Firewall,
Secure Protocols, and User Login.
Measurement units:
N/A
Issues:
None
See Also:
Benchmark Planes
Security Plane Configuration Set
Security Plane Startup Conditions
Security Plane Instability Conditions
Security Plane Failure Conditions
3.2 Configuration Sets
Definition:
The features and scaling limits used during the Accelerated Stress
Benchmarking.
Discussion:
There are four Configuration Sets: Control Plane Configuration Set,
Data Plane Configuration Set, Management Plane Configuration Set,
and Security Plane Configuration Set.
Measurement units: N/A
Issues: None
See Also:
Control Plane Configuration Set
Data Plane Configuration Set
Management Plane Configuration Set
Security Plane Configuration Set
Poretsky, Rao, Piatt [Page 6]
INTERNET-DRAFT Terminology for Accelerated Stress Benchmarking October 2003
3.2.1 Control Plane Configuration Set
Definition:
The routing protocols and scaling values used for the Accelerated
Life Benchmarking.
Discussion:
Control Plane Configuration Set is shown in Figure 2 and specifies
the Routing Protocols, Multicast, and MPLS configuration. Specific
protocols can be enabled or disabled for a benchmark test.
Measurement units: None
Issues: None
____________ ____________ ____________
| Routing | | Multicast | | MPLS |
| Protocols |___ | Protocols | __| Protocols |
| | | | | | | |
------------ | ------------ | ------------
| | |
| | |
| \/ |
| ___________ |
| | | |
|------->| DUT |<------|
| |
-----------
Figure 2. Control Plane Configuration Module
See Also:
Data Plane Configuration Set
Management Configuration Set
Security Configuration Set
3.2.2 Data Plane Configuration Set
Definition:
The data traffic profile enabled for the Accelerated Stress
Benchmarking.
Discussion:
Data Plane Configuration Set includes the Traffic Profile and
interfaces used for the Accelerated Stress Benchmarking.
Measurement Units:
N/A
Issues:
None
See Also:
Traffic Profile
Poretsky, Rao, Piatt [Page 7]
INTERNET-DRAFT Terminology for Accelerated Stress Benchmarking October 2003
3.2.2.1 Traffic Profile
Definition
The characteristics of the Offered Load to the DUT used for
the Accelerated Stress Benchmarking.
Discussion
The Traffic Profile specifies the number of packet size(s), packet
rate per interface, number of flows, and encapsulation used for the offered load to the DUT.
Measurement Units:
Traffic Profile is reported as follows:
Parameter Units
--------- ------
Packet Size(s) bytes
Packet Rate(interface) array of packets per second
Number of Flows number
Encapsulation(flow) array of encapsulation type
Issues:
None
See Also:
Data Plane Configuration Set
3.2.3 Management Plane Configuration Set
Definition:
The router management features enabled for the
Accelerated Stress Test.
Discussion:
A key component of the Accelerated Stress Test is the Management Configuration Set to assess manageability of the router under
stress. The Management Configuration Set defines the management configuration of the DUT. Features that are part of the
Management Configuration Set include SNMP, Logging/Debug, and
Statistics Collection, and services such as FTP, as shown in
Figure 3.
Measurement units:
N/A
Issues:
None
See Also:
Control Plane Configuration Set
Data Plane Configuration Set
Security Plane Configuration Set
Poretsky, Rao, Piatt [Page 8]
INTERNET-DRAFT Terminology for Accelerated Stress Benchmarking October 2003
____________ ____________
| | | Logging/ |
| SNMP | __| Debug |
| | | | |
------------ | ------------
| |
| |
\/ |
___________ |
| | |
| DUT |<---|
| |
-----------
|
|
\/
___________
| Packet |
| Statistics|
| Collector |
| |
-----------
Figure 3. Management Plane Configuration Set
3.2.4 Security Plane Configuration Set
Definition:
Security features and scaling enabled for the Accelerated Stress
Test.
Discussion:
The Security Plane Configuration Set includes the configuration
and scaling of ACLs, Firewall, IPsec, and User Access, as shown
in Figure 4.
____________ ____________ ____________
| | | Secure | | User |
|ACL/Firewall| | Protocol | __| Access |
| | | | | | |
------------ ------------ | ------------
| | |
| | |
| \/ |
| ___________ |
| | | |
|-------> | DUT |<--------|
| |
-----------
Figure 4. Security Configuration Module
Poretsky, Rao, Piatt [Page 9]
INTERNET-DRAFT Terminology for Accelerated Stress Benchmarking October 2003
Measurement units:
N/A
Issues:
None
See Also:
ACL Configuration Set
Secure Protocol Configuration Set
Password Login Configuration Set
3.3 Startup Conditions
Definition:
Test conditions that occur at the start of the Accelerated
Life Benchmark to establish conditions for the remainder of
the test.
Discussion:
Startup Conditions may cause stress on the DUT and produce
failure. Startup Conditions are defined for the Control
Plane and Security Plane.
Measurement units:
N/A
Issues:
None
See Also:
Control Plane Startup Conditions
Data Plane Startup Conditions
Management Plane Startup Conditions
Security Plane Startup Conditions
3.3.1 Control Plane Startup Conditions
Definition:
Control Plane conditions that occur at the start
of the Accelerated Stress Benchmarking to establish conditions
for the remainder of the test.
Discussion:
Startup Conditions may cause stress on the DUT and produce
failure. Startup Conditions for the Control Plane include
session establishment rate, number of sessions established
and number of routes learned.
Measurement units:
N/A
Poretsky, Rao, Piatt [Page 10]
INTERNET-DRAFT Terminology for Accelerated Stress Benchmarking October 2003
Issues:
None
See Also:
Startup Conditions
Security Plane Startup Conditions
Control Plane Configuration Set
3.3.2 Security Plane Startup Conditions
Definition:
Security Plane conditions that occur at the start
of the Accelerated Stress Benchmarking to establish conditions
for the remainder of the test.
Discussion:
Startup Conditions may cause stress on the DUT and produce
failure. Startup Conditions for the Security Plane include
session establishment rate, number of sessions established
and number of policies learned, and number of user access
sessions opened.
Measurement units:
N/A
Issues:
None
See Also:
Startup Conditions
Data Plane Startup Conditions
Management Plane Startup Conditions
Security Plane Startup Conditions
3.4 Instability Conditions
Definition:
Test conditions that occur during the Accelerated Stress
Benchmark to produce instability and stress the DUT.
Discussion:
Instability Conditions are experienced by the DUT after the
Startup Conditions have completed. Instability Conditions
occur for the Control Plane, Data Plane, Management Plane,
and Security Plane.
Measurement units:
N/A
Issues:
None
Poretsky, Rao, Piatt [Page 11]
INTERNET-DRAFT Terminology for Accelerated Stress Benchmarking October 2003
See Also:
Control Plane Instability Conditions
Data Plane Instability Conditions
Management Plane Instability Conditions
Security Plane Instability Conditions
3.4.1 Control Plane Instability Conditions
Definition:
Control Plane conditions that occur during the Accelerated Stress
Benchmark to produce instability and stress the DUT.
Discussion:
Control Plane Instability Conditions are experienced by the DUT
after the Startup Conditions have completed. Control Plane
Instability Conditions experienced by the DUT include session
loss, route withdrawal, and route cost changes.
Measurement units:
N/A
Issues:
None
See Also:
Instability Conditions
Data Plane Instability Conditions
Management Plane Instability Conditions
Security Plane Instability Conditions
3.4.2 Data Plane Instability Conditions
Definition:
Data Plane conditions that occur during the Accelerated Stress
Benchmark to produce instability and stress the DUT.
Discussion:
Data Plane Instability Conditions are experienced by the DUT
after the Startup Conditions have completed. Data Plane
Instability Conditions experienced by the DUT include interface
shutdown, link loss, and overloaded links.
Measurement units:
N/A
Issues:
None
See Also:
Instability Conditions
Control Plane Instability Conditions
Management Plane Instability Conditions
Security Plane Instability Conditions
Poretsky, Rao, Piatt [Page 12]
INTERNET-DRAFT Terminology for Accelerated Stress Benchmarking October 2003
3.4.3 Management Plane Instability Conditions
Definition:
Management Plane conditions that occur during the Accelerated
Life Benchmark to produce instability and stress the DUT.
Discussion:
Management Plane Instability Conditions are experienced by the DUT
after the Startup Conditions have completed. Management Plane
Instability Conditions experienced by the DUT include repeated
FTP of large files.
Measurement units:
N/A
Issues:
None
See Also:
Instability Conditions
Control Plane Instability Conditions
Data Plane Instability Conditions
Security Plane Instability Conditions
3.4.4 Security Plane Instability Conditions
Definition:
Security Plane conditions that occur during the Accelerated
Life Benchmark to produce instability and stress the DUT.
Discussion:
Security Plane Instability Conditions are experienced by the DUT
after the Startup Conditions have completed. Security Plane
Instability Conditions experienced by the DUT include session
loss and policy changes.
Measurement units:
N/A
Issues:
None
See Also:
Instability Conditions
Control Plane Instability Conditions
Data Plane Instability Conditions
Management Plane Instability Conditions
Poretsky, Rao, Piatt [Page 13]
INTERNET-DRAFT Terminology for Accelerated Stress Benchmarking October 2003
3.5 Failure Conditions
3.5.1 Unexpected Session Loss
Definition:
Session Loss due to Control Plane or Data Plane failure during the
Accelerated Stress Benchmarking.
Discussion:
Session loss will be observed due to Convergence Events produced
by the Instability Conditions. This is not considered a failure
during the Accelerated Stress Benchmarking. It is expected behavior.
Unexpected packet loss occurs due to Data Plane or Control Plane
failure.
Measurement units:
sessions
Issues:
None
See Also:
Unexpected Packet Loss
Misrouted Packets
Access Denial
Errored Management Values
Security Plane Failure
3.5.2 Unexpected Packet Loss
Definition:
Packet Loss due to Control Plane or Data Plane failure during the
Accelerated Stress Benchmarking.
Discussion:
Packet loss will be observed due to Convergence Events produced
by the Instability Conditions. This is not considered a failure
during the Accelerated Stress Benchmarking. It is expected behavior.
Unexpected packet loss occurs due to Data Plane or Control Plane
failure.
Measurement units:
packets
Issues:
None
See Also:
Unexpected Session Loss
Misrouted Packets
Access Denial
Errored Management Values
Security Plane Failure
Poretsky, Rao, Piatt [Page 14]
INTERNET-DRAFT Terminology for Accelerated Stress Benchmarking October 2003
3.5.3 Misrouted Packets
Definition:
Packets routed to the incorrect next-hop or LSP due to Control
Plane failure during the Accelerated Stress Benchmarking.
Discussion:
Packets will be rerouted to new next-hops and LSPs due to Convergence
Events produced by the Instability Conditions. This is not considered
a failure during the Accelerated Stress Benchmarking. It is expected
behavior. Unexpected Misrouted packets occur due to Control Plane
failure.
Measurement units:
packets
Issues:
None
See Also:
Unexpected Packet Loss
Unexpected Session Loss
Access Denial
Errored Management Values
Security Plane Failure
3.5.4 Access Denial
Definition:
Inability to management the DUT due to the inability
to gain remote access to the DUT.
Discussion:
Handling of Instability Conditions may cause a Control Plane failure
of the DUT externally observable as the inability to remotely manage
the DUT. Whether using SNMP, Telnet, SSH, or FTP, failure to manage
the device constitues a failure.
Measurement units:
Failed session
Issues:
None
See Also:
Unexpected Packet Loss
Unexpected Session Loss
Misrouted Packets
Errored Management Value
Security Plane Failure
Poretsky, Rao, Piatt [Page 15]
INTERNET-DRAFT Terminology for Accelerated Stress Benchmarking October 2003
3.5.5 Errored Management Value
Definition:
Incorrect SNMP object value or statistic during the Accelerated
Life Benchmark.
Discussion:
Management of a router relies upon accurate reporting of object
values and statistics. The Accelerated Stress Benchmarkinging validates
that the DUT is able to report correct values when experiencing
Instability Conditions.
Measurement units:
Name of incorrect object or statistic
Issues:
None
See Also:
Unexpected Packet Loss
Unexpected Session Loss
Misrouted Packets
Access Denial
Security Plane Failure
Success Threshold
3.5.6 Security Plane Failure
Definition:
Violation of Security Policy for packets directed to the DUT
or routed through the DUT.
Discussion:
Security Policy is configured to permit and deny access to packets
destined for the DUT and packets to be routed through the DUT.
A violation of this security policy is when either a packet to
be denied is permitted or a packet to be permitted is denied.
Measurement units:
packets
Issues:
None
See Also:
Unexpected Packet Loss
Unexpected Session Loss
Misrouted Packets
Access Denial
Errored Management Value
Poretsky, Rao, Piatt [Page 16]
INTERNET-DRAFT Terminology for Accelerated Stress Benchmarking October 2003
3.6 Benchmarks
3.6.1 Success Threshold
Definition:
The intended number of hours for the DUT to operate without failure
during the Accelerated Stress Benchmarking.
Discussion:
Success Threshold is a user determined value of time. It is
necessary to define the Success Threshold because it is possible
for the DUT to experience zero failures for given Configuration
Sets, Startup Conditions, and Instability Conditions
Measurement units:
Hours
Issues:
None
See Also:
Accelerated-Life Test Duration
3.6.2 Accelerated-Life Test Duration
Definition:
The run-time for the Accelerated Stress Test without the DUT
exhibiting an error in the control plane, data plane, management
plane, or security plane.
Discussion:
For a successful test, the Test Duration will equal the
Success Threshold. In the event of any failure, the Test Duration
is less than the Success Threshold. Reporting of the Test
Duration MUST inlcude the Failure Condition from those defined
in this document.
Measurement units:
Hours
Issues:
None
See Also:
Success Threshold
Poretsky, Rao, Piatt [Page 17]
INTERNET-DRAFT Terminology for Accelerated Stress Benchmarking October 2003
4. Security Considerations
Documents of this type do not directly effect the security of
the Internet or of corporate networks as long as benchmarking
is not performed on devices or systems connected to operating
networks.
5. References
[1] Bradner, S., Editor, "Benchmarking Terminology for Network
Interconnection Devices", RFC 1242, July 1991.
[2] Mandeville, R., "Benchmarking Terminology for LAN Switching
Devices", RFC 2285, June 1998.
[3] Bradner, S. and McQuaid, J., "Benchmarking Methodology for
Network Interconnect Devices", RFC 2544, March 1999.
[4] "Core Router Evaluation for Higher Availability", Scott
Poretsky, NANOG 25, June 8, 2002, Toronto, CA.
[5] "Router Stress Testing to Validate Readiness for Network
Deployment", Scott Poretsky, IEEE CQR 2003.
6. Author's Address
Scott Poretsky
Quarry Technologies
8 New England Executive Park
Burlington, MA 01803
USA
Phone: + 1 781 395 5090
EMail: sporetsky@quarrytech.com
Shankar Rao
950 17th Street
Suite 1900
Qwest Communications
Denver, CO 80210
USA
Phone: + 1 303 437 6643
Email: srao@qwest.net
Ray Piatt
Cable and Wireless
11700 Plaza America Drive
Reston, VA 20190
USA
Phone: + 1 703 292 2113
Email: rpiatt@cw.net
Poretsky, Rao, Piatt [Page 18]
INTERNET-DRAFT Terminology for Accelerated Stress Benchmarking October 2003
7. Full Copyright Statement
Copyright (C) The Internet Society (1998). All Rights
Reserved.
This document and translations of it may be copied and
furnished to others, and derivative works that comment on or
otherwise explain it or assist in its implementation may be
prepared, copied, published and distributed, in whole or in
part, without restriction of any kind, provided that the above
copyright notice and this paragraph are included on all such
copies and derivative works. However, this document itself may
not be modified in any way, such as by removing the copyright
notice or references to the Internet Society or other Internet
organizations, except as needed for the purpose of developing
Internet standards in which case the procedures for copyrights
defined in the Internet Standards process must be followed, or
as required to translate it into languages other than English.
The limited permissions granted above are perpetual and will
not be revoked by the Internet Society or its successors or
assigns. This document and the information contained herein is
provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE
INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY
THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY
RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE.
Poretsky, Rao, Piatt [Page 19]
INTERNET-DRAFT Terminology for Accelerated Stress Benchmarking October 2003
Appendix 1. White Box Benchmarking Terminology
Appendix 1.1 Minimum Available Memory
Definition:
Minimum DUT Available Memory during the duration of the
Accelerated Stress Test.
Discussion:
It is necessary to monitor DUT memory to measure this
benchmark.
Measurement units:
bytes
Issues:
None
See Also:
Maximum CPU Utilization
Appendix 1.2 Maximum CPU Utilization
Definition:
Maximum DUT CPU utilization during the duration of the
Accelerated Stress Test.
Discussion:
It is necessary to monitor DUT CPU Utilization to measure
this benchmark.
Measurement units:
%
Issues:
None
See Also:
Minimum Available Memory
Poretsky, Rao, Piatt [Page 20]
| PAFTECH AB 2003-2026 | 2026-04-23 11:42:51 |