One document matched: draft-ietf-avt-srtp-big-aes-01.txt
Differences from draft-ietf-avt-srtp-big-aes-00.txt
Network Working Group D. McGrew
Internet-Draft Cisco Systems, Inc.
Intended status: Standards Track July 6, 2009
Expires: January 7, 2010
The use of AES-192 and AES-256 in Secure RTP
draft-ietf-avt-srtp-big-aes-01.txt
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on January 7, 2010.
Copyright Notice
Copyright (c) 2009 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents in effect on the date of
publication of this document (http://trustee.ietf.org/license-info).
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document.
McGrew Expires January 7, 2010 [Page 1]
Internet-Draft SRTP AES-192 and AES-256 July 2009
Abstract
This memo describes the use of the Advanced Encryption Standard (AES)
with 192 and 256 bit keys within the Secure RTP protocol. It defines
Counter Mode encryption for SRTP and SRTCP and a new SRTP Key
Derivation Function (KDF) for AES-192 and AES-256.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Conventions Used In This Document . . . . . . . . . . . . 3
2. AES-192 and AES-256 Encryption . . . . . . . . . . . . . . . . 4
3. The AES_192_CM_PRF and AES_256_CM_PRF Key Derivation
Functions . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.1. Usage Requirements . . . . . . . . . . . . . . . . . . . . 6
4. Crypto Suties . . . . . . . . . . . . . . . . . . . . . . . . 7
5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 11
6. Security Considerations . . . . . . . . . . . . . . . . . . . 12
7. Test Cases . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7.1. AES-256-CM Test Cases . . . . . . . . . . . . . . . . . . 13
7.2. AES_256_CM_PRF Test Cases . . . . . . . . . . . . . . . . 13
7.3. AES-192-CM Test Cases . . . . . . . . . . . . . . . . . . 15
7.4. AES_192_CM_PRF Test Cases . . . . . . . . . . . . . . . . 15
8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 18
9. References . . . . . . . . . . . . . . . . . . . . . . . . . . 19
9.1. Normative References . . . . . . . . . . . . . . . . . . . 19
9.2. Informative References . . . . . . . . . . . . . . . . . . 19
Author's Address . . . . . . . . . . . . . . . . . . . . . . . . . 20
McGrew Expires January 7, 2010 [Page 2]
Internet-Draft SRTP AES-192 and AES-256 July 2009
1. Introduction
This memo describes the use of the Advanced Encryption Standard (AES)
[FIPS197] with 192 and 256 bit keys within the Secure RTP protocol
[RFC3711]. Below those block ciphers are referred to as AES-192 and
AES-256, respectively, and the use of AES with a 128 bit key is
referred to as AES-128. This document defines Counter Mode
encryption for SRTP and SRTCP and a new SRTP Key Derivation Function
for AES-192 and AES-256. It also defines new cryptosuites that use
these new functions.
While AES-128 is widely regarded as more than adequately secure, some
users may be motivated to adopt AES-192 or AES-256. One motivation
is conformance to the Suite B profile (which requires AES-256 for the
protection of TOP SECRET information) [suiteB]. Others may be
motivated by a perceived need to purse a highly conservative security
strategy; see Section 6 for more discussion of security issues.
The crypto functions defined in this document are an addition to, and
not a replacement for, the crypto functions defined in [RFC3711].
1.1. Conventions Used In This Document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
McGrew Expires January 7, 2010 [Page 3]
Internet-Draft SRTP AES-192 and AES-256 July 2009
2. AES-192 and AES-256 Encryption
Section 4.1.1 of [RFC3711] defines AES-128 counter mode encryption,
which it refers to as AES_CM. AES-192 counter mode and AES-256
counter mode are defined in a similar manner, and are denoted as
AES_192_CM and AES_256_CM respectively. In both of these ciphers,
the plaintext inputs to the block cipher are formed as in AES_CM, and
the block cipher outputs are processed as in AES_CM. The only
difference in the processing is that AES_192_CM uses AES-192, and
AES_256_CM uses AES-256. Both AES_192_CM and AES_256_CM use a 112-
bit salt as an input, as does AES_CM.
For the convenience of the reader, the structure of the counter
blocks in SRTP counter mode encryption is illustrated in Figure 1,
using the terminology from Section 4.1.1 of [RFC3711] . In this
diagram, the symbol (+) denotes the bitwise exclusive-or operation,
and the AES encrypt operation uses AES-128, AES-192, or AES-256 for
AES_CM, AES_192_CM, and AES_256_CM, respectively. The field labeled
b_c contains a block counter, the value of which increments once for
each invocation of the "AES Encrypt" function.
one octet
<-->
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+
|00|00|00|00| SSRC | packet index | b_c |---+
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ |
|
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ v
| salt (k_s) |00|00|->(+)
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ |
|
v
+-------------+
encryption key (k_e) -> | AES encrypt |
+-------------+
|
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ |
| keystream block |<--+
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+
Figure 1: AES Counter Mode.
McGrew Expires January 7, 2010 [Page 4]
Internet-Draft SRTP AES-192 and AES-256 July 2009
3. The AES_192_CM_PRF and AES_256_CM_PRF Key Derivation Functions
Section 4.3.3 of [RFC3711] defines AES-128 counter mode key
derivation function, which it refers to as "AES-CM PRF". (That
specification uses the term PRF, or pseudo-random function,
interchangeably with the term "key derivation function". ) The AES-
192 counter mode PRF and AES-256 counter mode PRF are defined in a
similar manner, and are denoted as AES_192_CM_PRF and AES_256_CM_PRF
respectively. In both of these PRFs, the plaintext inputs to the
block cipher are formed as in the AES-CM PRF, and the block cipher
outputs are processed as in the AES-CM PRF. The only difference in
the processing is that AES_192_CM_PRF uses AES-192, and
AES_256_CM_PRF uses AES-256. Both AES_192_CM_PRF and AES_256_CM_PRF
use a 112-bit salt as an input, as does the AES-CM PRF.
For the convenience of the reader, the structure of the counter
blocks in SRTP counter mode key derivation is illustrated in
Figure 2, using the terminology from Section 4.3.3 of [RFC3711]. In
this diagram, the symbol (+) denotes the bitwise exclusive-or
operation, and the "AES Encrypt" operation uses AES-128, AES-192, or
AES-256 for the "AES-CM PRF", AES_192_CM_PRF, and AES_256_CM_PRF,
respectively. The field "LB" contains the 8-bit constant "label"
which is provided as an input to the key derivation function (and
which is distinct for each type of key generated by that function).
The field labeled b_c contains a block counter, the value of which
increments once for each invocation of the "AES Encrypt" function.
one octet
<-->
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+
|00|00|00|00|00|00|00|LB| index DIV kdr | b_c |---+
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ |
|
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ v
| master salt |00|00|->(+)
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ |
|
v
+-------------+
master key -> | AES encrypt |
+-------------+
|
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ |
| output block |<--+
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+
Figure 2: The AES counter mode Key Derivation Function
McGrew Expires January 7, 2010 [Page 5]
Internet-Draft SRTP AES-192 and AES-256 July 2009
3.1. Usage Requirements
When AES_192_CM is used for encryption, AES_192_CM SHOULD be used as
the key derivation function, and AES_128_CM MUST NOT be used as the
key derivation function.
When AES_256_CM is used for encryption, AES_256_CM SHOULD be used as
the key derivation function. Both AES_128_CM and AES_192_CM MUST NOT
be used as the key derivation function.
Rationale: it is essential that the cryptographic strength of the
key derivation meets or exceeds that of the encryption method. It
is natural to use the same function for both encryption and key
derivation. However, it is not required to do so because it is
desirable to allow these ciphers to be used with alternative key
derivation functions that may be defined in the future.
McGrew Expires January 7, 2010 [Page 6]
Internet-Draft SRTP AES-192 and AES-256 July 2009
4. Crypto Suties
This section defines SRTP crypto suites that use the ciphers and key
derivation functions defined in this document. These suites are
registered with IANA for use with the SDP Security Descriptions
attributes (Section 10.3.2.1 of [RFC4568]). Other SRTP key
management methods that use the crypto functions defined in this
document are encouraged to also use these crypto suite definitions.
+------------------------------+------------------------------------+
| Parameter | Value |
+------------------------------+------------------------------------+
| Master key length | 192 bits |
| | |
| Master salt length | 112 bits |
| | |
| Key Derivation Function | AES_192_CM_PRF (Section 3) |
| | |
| Default key lifetime | 2^31 packets |
| | |
| Cipher (for SRTP and SRTCP) | AES_192_CM (Section 2) |
| | |
| SRTP authentication function | HMAC-SHA1 (Section 4.2.1 of |
| | [RFC3711]) |
| | |
| SRTP authentication key | 160 bits |
| length | |
| | |
| SRTP authentication tag | 80 bits |
| length | |
| | |
| SRTCP authentication | HMAC-SHA1 (Section 4.2.1 of |
| function | [RFC3711]) |
| | |
| SRTCP authentication key | 160 bits |
| length | |
| | |
| SRTCP authentication tag | 80 bits |
| length | |
+------------------------------+------------------------------------+
Table 1: The AES_192_CM_HMAC_SHA1_80 cryptosuite.
McGrew Expires January 7, 2010 [Page 7]
Internet-Draft SRTP AES-192 and AES-256 July 2009
+------------------------------+------------------------------------+
| Parameter | Value |
+------------------------------+------------------------------------+
| Master key length | 192 bits |
| | |
| Master salt length | 112 bits |
| | |
| Key Derivation Function | AES_192_CM_PRF (Section 3) |
| | |
| Default key lifetime | 2^31 packets |
| | |
| Cipher (for SRTP and SRTCP) | AES_192_CM (Section 2) |
| | |
| SRTP authentication function | HMAC-SHA1 (Section 4.2.1 of |
| | [RFC3711]) |
| | |
| SRTP authentication key | 160 bits |
| length | |
| | |
| SRTP authentication tag | 32 bits |
| length | |
| | |
| SRTCP authentication | HMAC-SHA1 (Section 4.2.1 of |
| function | [RFC3711]) |
| | |
| SRTCP authentication key | 160 bits |
| length | |
| | |
| SRTCP authentication tag | 80 bits |
| length | |
+------------------------------+------------------------------------+
Table 2: The AES_192_CM_HMAC_SHA1_32 cryptosuite.
McGrew Expires January 7, 2010 [Page 8]
Internet-Draft SRTP AES-192 and AES-256 July 2009
+------------------------------+------------------------------------+
| Parameter | Value |
+------------------------------+------------------------------------+
| Master key length | 256 bits |
| | |
| Master salt length | 112 bits |
| | |
| Key Derivation Function | AES_256_CM_PRF (Section 3) |
| | |
| Default key lifetime | 2^31 packets |
| | |
| Cipher (for SRTP and SRTCP) | AES_256_CM (Section 2) |
| | |
| SRTP authentication function | HMAC-SHA1 (Section 4.2.1 of |
| | [RFC3711]) |
| | |
| SRTP authentication key | 160 bits |
| length | |
| | |
| SRTP authentication tag | 80 bits |
| length | |
| | |
| SRTCP authentication | HMAC-SHA1 (Section 4.2.1 of |
| function | [RFC3711]) |
| | |
| SRTCP authentication key | 160 bits |
| length | |
| | |
| SRTCP authentication tag | 80 bits |
| length | |
+------------------------------+------------------------------------+
Table 3: The AES_256_CM_HMAC_SHA1_80 cryptosuite.
McGrew Expires January 7, 2010 [Page 9]
Internet-Draft SRTP AES-192 and AES-256 July 2009
+------------------------------+------------------------------------+
| Parameter | Value |
+------------------------------+------------------------------------+
| Master key length | 256 bits |
| | |
| Master salt length | 112 bits |
| | |
| Key Derivation Function | AES_256_CM_PRF (Section 3) |
| | |
| Default key lifetime | 2^31 packets |
| | |
| Cipher (for SRTP and SRTCP) | AES_256_CM (Section 2) |
| | |
| SRTP authentication function | HMAC-SHA1 (Section 4.2.1 of |
| | [RFC3711]) |
| | |
| SRTP authentication key | 160 bits |
| length | |
| | |
| SRTP authentication tag | 32 bits |
| length | |
| | |
| SRTCP authentication | HMAC-SHA1 (Section 4.2.1 of |
| function | [RFC3711]) |
| | |
| SRTCP authentication key | 160 bits |
| length | |
| | |
| SRTCP authentication tag | 80 bits |
| length | |
+------------------------------+------------------------------------+
Table 4: The AES_256_CM_HMAC_SHA1_32 cryptosuite.
McGrew Expires January 7, 2010 [Page 10]
Internet-Draft SRTP AES-192 and AES-256 July 2009
5. IANA Considerations
IANA is expected to assign the following parameters for the SDP
Security Descriptions crypto suite attribute.
AES_192_CM_HMAC_SHA1_80
AES_192_CM_HMAC_SHA1_32
AES_256_CM_HMAC_SHA1_80
AES_256_CM_HMAC_SHA1_32
The cryptosuites are as defined in Section 4.
McGrew Expires January 7, 2010 [Page 11]
Internet-Draft SRTP AES-192 and AES-256 July 2009
6. Security Considerations
AES-128 provides a level of security that is widely regarded as being
more than sufficient for providing confidentiality. It is believed
that the economic cost of breaking AES-128 is significantly higher
than the cost of more direct approaches to violating system security,
e.g. theft, bribery, wiretapping, and other forms of malfeasance.
Future advances in the state of the art of cryptanalysis could
eliminate this confidence in AES-128, and motivate the use of AES-192
or AES-256. AES-192 is regarded as being secure even against some
adversaries for which breaking AES-128 may be feasible. Similarly,
AES-256 is regarded as being secure even against some adversaries for
which it may be feasible to break AES-192. The availability of the
larger key size versions of AES provides a fallback plan in case of
unanticipated cryptanalytic results.
It is conjectured that AES-256 provides adequate security even
against adversaries that possess the ability to construct a quantum
computer that works on 256 or more quantum bits. No such computer is
known to exist; its feasibility is an area of active speculation and
research.
Despite the apparent sufficiency of AES-128, some users are
interested in the larger AES key sizes. For some applications, the
40% increase in computational cost for AES-256 over AES-128 is a
worthwhile bargain when traded for the security advantages outlined
above. These applications include those with a perceived need for
very high security, e.g. due to a desire for very long-term
confidentiality.
As with any cipher, the conjectured security level of AES may change
over time. The considerations in this section reflect the best
knowledge available at the time of publication of this document.
It is desirable that AES_192_CM and AES_192_CM_PRF be used with an
authentication function that uses a 192 bit key, and that AES_256_CM
and AES_256_CM_PRF be used with an authentication function that uses
a 256 bit key. However, this desire is not regarded as security-
critical. Cryptographic authentication is resilient against future
advances in cryptanalysis, since the opportunity for a forgery attack
against a session closes when that session closes.
McGrew Expires January 7, 2010 [Page 12]
Internet-Draft SRTP AES-192 and AES-256 July 2009
7. Test Cases
The test cases in this section are based on Appendix B of [RFC3711].
7.1. AES-256-CM Test Cases
Keystream segment length: 1044512 octets (65282 AES blocks)
Session Key: 57f82fe3613fd170a85ec93c40b1f092
2ec4cb0dc025b58272147cc438944a98
Rollover Counter: 00000000
Sequence Number: 0000
SSRC: 00000000
Session Salt: f0f1f2f3f4f5f6f7f8f9fafbfcfd0000 (already shifted)
Offset: f0f1f2f3f4f5f6f7f8f9fafbfcfd0000
Counter Keystream
f0f1f2f3f4f5f6f7f8f9fafbfcfd0000 92bdd28a93c3f52511c677d08b5515a4
f0f1f2f3f4f5f6f7f8f9fafbfcfd0001 9da71b2378a854f67050756ded165bac
f0f1f2f3f4f5f6f7f8f9fafbfcfd0002 63c4868b7096d88421b563b8c94c9a31
... ...
f0f1f2f3f4f5f6f7f8f9fafbfcfdfeff cea518c90fd91ced9cbb18c078a54711
f0f1f2f3f4f5f6f7f8f9fafbfcfdff00 b4d49c8aec7ccb7726f14f338d19d88a
f0f1f2f3f4f5f6f7f8f9fafbfcfdff01 c6f6a4804386cf175903139119b4fbde
7.2. AES_256_CM_PRF Test Cases
This section provides test data for the AES_256_CM_PRF key derivation
function, which uses AES-256 in Counter Mode. In the following, we
walk through the initial key derivation for the AES-256 Counter Mode
cipher, which requires a 32 octet session encryption key and a 14
octet session salt, and the HMAC-SHA1 authentication function, which
requires a 20-octet session authentication key. These values are
called the cipher key, the cipher salt, and the auth key in the
following. Since this is the initial key derivation and the key
derivation rate is equal to zero, the value of (index DIV
key_derivation_rate) is zero (actually, a six-octet string of zeros).
In the following, we shorten key_derivation_rate to kdr.
The inputs to the key derivation function are the 32 octet master key
and the 14 octet master salt:
master key: f0f04914b513f2763a1b1fa130f10e29
98f6f6e43e4309d1e622a0e332b9f1b6
master salt: 3b04803de51ee7c96423ab5b78d2
We first show how the cipher key is generated. The input block for
McGrew Expires January 7, 2010 [Page 13]
Internet-Draft SRTP AES-192 and AES-256 July 2009
AES-256-CM is generated by exclusive-oring the master salt with the
concatenation of the encryption key label 0x00 with (index DIV kdr),
then padding on the right with two null octets (which implements the
multiply-by-2^16 operation, see Section 4.3.3 of RFC 3711). The
resulting value is then AES-256-CM- encrypted using the master key to
get the cipher key.
index DIV kdr: 000000000000
label: 00
master salt: 3b04803de51ee7c96423ab5b78d2
-----------------------------------------------
xor: 3b04803de51ee7c96423ab5b78d2 (x, PRF input)
x*2^16: 3b04803de51ee7c96423ab5b78d20000 (AES-256-CM input)
x*2^16 + 1: 3b04803de51ee7c96423ab5b78d20001 (2nd AES input)
cipher key: 5ba1064e30ec51613cad926c5a28ef73 (1st AES output)
1ec7fb397f70a960653caf06554cd8c4 (2nd AES output)
Next, we show how the cipher salt is generated. The input block for
AES-256-CM is generated by exclusive-oring the master salt with the
concatenation of the encryption salt label. That value is padded and
encrypted as above.
index DIV kdr: 000000000000
label: 02
master salt: 3b04803de51ee7c96423ab5b78d2
----------------------------------------------
xor: 3b04803de51ee7cb6423ab5b78d2 (x, PRF input)
x*2^16: 3b04803de51ee7cb6423ab5b78d20000 (AES-256-CM input)
fa31791685ca444a9e07c6c64e93ae6b (AES-256 ouptut)
cipher salt: fa31791685ca444a9e07c6c64e93
We now show how the auth key is generated. The input block for AES-
256-CM is generated as above, but using the authentication key label.
McGrew Expires January 7, 2010 [Page 14]
Internet-Draft SRTP AES-192 and AES-256 July 2009
index DIV kdr: 000000000000
label: 01
master salt: 3b04803de51ee7c96423ab5b78d2
-----------------------------------------------
xor: 3b04803de51ee7c86423ab5b78d2 (x, PRF input)
x*2^16: 3b04803de51ee7c86423ab5b78d20000 (AES-256-CM in)
Below, the AES-256 output blocks that form the auth key are shown
on the left, while the corresponding AES-256 input blocks are shown
on the right. Note that the final AES-256 output is truncated to a
four-byte length. The final auth key is shown below.
auth key blocks AES-256 input blocks
fd9c32d39ed5fbb5a9dc96b30818454d 3b04803de51ee7c86423ab5b78d20000
1313dc05 3b04803de51ee7c86423ab5b78d20001
auth key: fd9c32d39ed5fbb5a9dc96b30818454d1313dc05
7.3. AES-192-CM Test Cases
Keystream segment length: 1044512 octets (65282 AES blocks)
Session Key: eab234764e517b2d3d160d587d8c8621
9740f65f99b6bcf7
Rollover Counter: 00000000
Sequence Number: 0000
SSRC: 00000000
Session Salt: f0f1f2f3f4f5f6f7f8f9fafbfcfd0000 (already shifted)
Offset: f0f1f2f3f4f5f6f7f8f9fafbfcfd0000
Counter Keystream
f0f1f2f3f4f5f6f7f8f9fafbfcfd0000 93853536732e0908a6cb28bd85b64776
f0f1f2f3f4f5f6f7f8f9fafbfcfd0001 a7e18fa46613babe588100d39d7ecbdd
f0f1f2f3f4f5f6f7f8f9fafbfcfd0002 1e39fa7aa435aa15bf5b607d44d1941d
... ...
f0f1f2f3f4f5f6f7f8f9fafbfcfdfeff cb82e54adb48c702633e2f757a2f4989
f0f1f2f3f4f5f6f7f8f9fafbfcfdff00 a3b2f7e1a988b0a90bb495081f17022f
f0f1f2f3f4f5f6f7f8f9fafbfcfdff01 3eeafd32fd6e4ee267f04e118a4b8f5b
7.4. AES_192_CM_PRF Test Cases
This section provides test data for the AES_256_CM_PRF key derivation
function, which uses AES-256 in Counter Mode. In the following, we
walk through the initial key derivation for the AES-256 Counter Mode
cipher, which requires a 32 octet session encryption key and a 14
McGrew Expires January 7, 2010 [Page 15]
Internet-Draft SRTP AES-192 and AES-256 July 2009
octet session salt, and the HMAC-SHA1 authentication function, which
requires a 20-octet session authentication key. These values are
called the cipher key, the cipher salt, and the auth key in the
following. Since this is the initial key derivation and the key
derivation rate is equal to zero, the value of (index DIV
key_derivation_rate) is zero (actually, a six-octet string of zeros).
In the following, we shorten key_derivation_rate to kdr.
The inputs to the key derivation function are the 32 octet master key
and the 14 octet master salt:
master key: 73edc66c4fa15776fb57f9505c171365
50ffda71f3e8e5f1
master salt: c8522f3acd4ce86d5add78edbb11
We first show how the cipher key is generated. The input block for
AES-256-CM is generated by exclusive-oring the master salt with the
concatenation of the encryption key label 0x00 with (index DIV kdr),
then padding on the right with two null octets (which implements the
multiply-by-2^16 operation, see Section 4.3.3 of RFC 3711). The
resulting value is then AES-256-CM- encrypted using the master key to
get the cipher key.
index DIV kdr: 000000000000
label: 00
master salt: c8522f3acd4ce86d5add78edbb11
-----------------------------------------------
xor: c8522f3acd4ce86d5add78edbb11 (x, PRF input)
x*2^16: c8522f3acd4ce86d5add78edbb110000 (AES-256-CM input)
x*2^16 + 1: c8522f3acd4ce86d5add78edbb110001 (2nd AES input)
cipher key: 6da8e1e082a06aa80e5cbb0661a5174a (1st AES output)
3b8636251d8e4c539e5923b5ddb30cd4 (2nd AES output)
Next, we show how the cipher salt is generated. The input block for
AES-256-CM is generated by exclusive-oring the master salt with the
concatenation of the encryption salt label. That value is padded and
encrypted as above.
McGrew Expires January 7, 2010 [Page 16]
Internet-Draft SRTP AES-192 and AES-256 July 2009
index DIV kdr: 000000000000
label: 02
master salt: c8522f3acd4ce86d5add78edbb11
----------------------------------------------
xor: c8522f3acd4ce86f5add78edbb11 (x, PRF input)
x*2^16: c8522f3acd4ce86f5add78edbb110000 (AES-256-CM input)
cf075c87408e8f8ad63fbd1ca9292eb4 (AES-256 ouptut)
cipher salt: cf075c87408e8f8ad63fbd1ca929
We now show how the auth key is generated. The input block for AES-
256-CM is generated as above, but using the authentication key label.
index DIV kdr: 000000000000
label: 01
master salt: c8522f3acd4ce86d5add78edbb11
-----------------------------------------------
xor: c8522f3acd4ce86c5add78edbb11 (x, PRF input)
x*2^16: c8522f3acd4ce86c5add78edbb110000 (AES-256-CM in)
Below, the AES-256 output blocks that form the auth key are shown
on the left, while the corresponding AES-256 input blocks are shown
on the right. Note that the final AES-256 output is truncated to a
four-byte length. The final auth key is shown below.
auth key blocks AES-256 input blocks
95f57950398ac4241ef5760b54bc5579 c8522f3acd4ce86c5add78edbb110000
6ae9adf7 c8522f3acd4ce86c5add78edbb110001
auth key: 95f57950398ac4241ef5760b54bc55796ae9adf7
McGrew Expires January 7, 2010 [Page 17]
Internet-Draft SRTP AES-192 and AES-256 July 2009
8. Acknowledgements
Thanks are due to John Mattsson for verifying the test cases in the
document, and to Bob Bell for feedback and encouragement.
McGrew Expires January 7, 2010 [Page 18]
Internet-Draft SRTP AES-192 and AES-256 July 2009
9. References
9.1. Normative References
[FIPS197] "The Advanced Encryption Standard (AES)", FIPS-197 Federal
Information Processing Standard.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3711] Baugher, M., McGrew, D., Naslund, M., Carrara, E., and K.
Norrman, "The Secure Real-time Transport Protocol (SRTP)",
RFC 3711, March 2004.
[RFC4568] Andreasen, F., Baugher, M., and D. Wing, "Session
Description Protocol (SDP) Security Descriptions for Media
Streams", RFC 4568, July 2006.
9.2. Informative References
[suiteB] "Fact Sheet for NSA Suite B Cryptography",
http://www.nsa.gov/ia/industry/crypto_suite_b.cfm.
McGrew Expires January 7, 2010 [Page 19]
Internet-Draft SRTP AES-192 and AES-256 July 2009
Author's Address
David A. McGrew
Cisco Systems, Inc.
510 McCarthy Blvd.
Milpitas, CA 95035
US
Phone: (408) 525 8651
Email: mcgrew@cisco.com
URI: http://www.mindspring.com/~dmcgrew/dam.htm
McGrew Expires January 7, 2010 [Page 20]
| PAFTECH AB 2003-2026 | 2026-04-23 13:05:50 |