One document matched: draft-ietf-16ng-ipv6-over-ipv6cs-02.txt
Differences from draft-ietf-16ng-ipv6-over-ipv6cs-01.txt
Network Working Group Basavaraj Patil
Internet-Draft Nokia
Intended status: Standards Track Frank Xia
Expires: June 7, 2007 Behcet Sarikaya
Huawei USA
JH. Choi
Samsung AIT
Syam Madanapalli
LogicaCMG
December 4, 2006
IPv6 Over the IP Specific part of the Packet Convergence sublayer in
802.16 Networks
draft-ietf-16ng-ipv6-over-ipv6cs-02
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on June 7, 2007.
Copyright Notice
Copyright (C) The Internet Society (2006).
Abstract
IEEE Std 802.16 is an air interface specification. IEEE has
Patil, et al. Expires June 7, 2007 [Page 1]
Internet-Draft IPv6 over Packet CS in 802.16 December 2006
specified several service specific convergence sublayers (CS) for
802.16 which are used by upper layer protocols. The ATM CS and
Packet CS are the two main service-specific convergence sublayers and
these are a part of the 802.16 MAC which the upper layers interface
to.The packet CS is used for transport for all packet-based protocols
such as Internet Protocol (IP), IEEE Std. 802.3 (Ethernet) and, IEEE
Std 802.1Q (VLAN). The IP specific part of the Packet CS enables
transport of IPv6 packets directly over the MAC. This document
specifies the addressing and operation of IPv6 over the IPv6 specific
part of the packet CS for hosts served by a network that utilizes the
IEEE Std 802.16 air interface. It recommends the assignment of a
unique prefix (or prefixes) to each host and allows the host to use
multiple identifiers within that prefix, including support for
randomly generated identifiers.
Patil, et al. Expires June 7, 2007 [Page 2]
Internet-Draft IPv6 over Packet CS in 802.16 December 2006
Table of Contents
1. Conventions used in this document . . . . . . . . . . . . . . 4
2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. IEEE 802.16 convergence sublayer support for IPv6 . . . . . . 5
4.1. IPv6 encapsulation over the IP CS of the MAC . . . . . . . 6
5. Generic network architecture using the 802.16 air interface . 7
5.1. WiMAX network architecture and IPv6 support . . . . . . . 8
6. IPv6 link . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6.1. IPv6 link in 802.16 . . . . . . . . . . . . . . . . . . . 10
6.1.1. IPv6 link in WiMAX . . . . . . . . . . . . . . . . . . 11
6.2. IPv6 link establishment in 802.16 . . . . . . . . . . . . 11
6.2.1. IPv6 link establishment in WiMAX . . . . . . . . . . . 12
6.3. Maximum transmission unit in 802.16 . . . . . . . . . . . 13
6.3.1. Maximum transmission unit in WiMAX . . . . . . . . . . 13
7. IPv6 prefix assignment . . . . . . . . . . . . . . . . . . . . 13
8. Router Discovery . . . . . . . . . . . . . . . . . . . . . . . 13
8.1. Router Solicitation . . . . . . . . . . . . . . . . . . . 13
8.2. Router Advertisement . . . . . . . . . . . . . . . . . . . 14
8.3. Router lifetime and periodic router advertisements . . . . 14
9. IPv6 addressing for hosts . . . . . . . . . . . . . . . . . . 14
9.1. Interface Identifier . . . . . . . . . . . . . . . . . . . 14
9.2. Duplicate address detection . . . . . . . . . . . . . . . 14
9.3. Stateless address autoconfiguration . . . . . . . . . . . 15
9.4. Stateful address autoconfiguration . . . . . . . . . . . . 15
10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 15
11. Security Considerations . . . . . . . . . . . . . . . . . . . 15
12. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 15
13. References . . . . . . . . . . . . . . . . . . . . . . . . . . 15
13.1. Normative References . . . . . . . . . . . . . . . . . . . 15
13.2. Informative References . . . . . . . . . . . . . . . . . . 16
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 17
Intellectual Property and Copyright Statements . . . . . . . . . . 19
Patil, et al. Expires June 7, 2007 [Page 3]
Internet-Draft IPv6 over Packet CS in 802.16 December 2006
1. Conventions used in this document
In this document, the key words "MUST", "MUST NOT", "REQUIRED",
"SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT
RECOMMENDED", "MAY", and "OPTIONAL" are to be interpreted as
described in BCP 14, RFC 2119 [RFC2119] and indicate requirement
levels for compliant implementations.
2. Introduction
IPv6 packets can be carried over the IEEE Std 802.16d specified air
interface via either:
1. the IP specific part of the Packet CS or,
2. the 802.3 specific part of the Packet CS or,
3. the 802.1Q specific part of the Packet CS.
The 802.16 [802.16e] specification includes the Phy and MAC details.
The convergence sublayers are a part of the MAC. This document
specifies IPv6 from the perspective of the transmission of IPv6 over
the IP specific part of the packet convergence sublayer. The mobile
station/host is attached to an access router via a base station (BS).
The host and the BS are connected via the IEEE Std 802.16 air
interface at the link and physical layers. The IPv6 link from the MS
terminates at an access router which may be a part of the BS or an
entity beyond the BS. The base station is a layer 2 entity (from the
perspective of the IPv6 link between the MS and AR) and relays the
IPv6 packets between the AR and the host via a point-to-point
connection over the air interface. The WiMAX (Worldwide
Interoperability for Microwave Access) forum [WMF] has defined a
network architecture in which the air interface is based on the IEEE
802.16 standard. The addressing and operation of IPv6 described in
this document is applicable to the WiMAX network as well.
3. Terminology
The terminology in this document is based on the definitions in
[PSDOC], in addition to the ones specified in this section.
Access Service Network (ASN) - The ASN is defined as a complete set
of network functions needed to provide radio access to a WiMAX
subscriber. The ASN is the access network to which the MS attaches.
The IPv6 access router is an entity within the ASN. The term ASN is
specific to the WiMAX network architecture.
Patil, et al. Expires June 7, 2007 [Page 4]
Internet-Draft IPv6 over Packet CS in 802.16 December 2006
4. IEEE 802.16 convergence sublayer support for IPv6
The IEEE 802.16 MAC specifies two main service specific convergence
sublayers:
1. ATM Convergence sublayer
2. Packet Convergence sublayer
The Packet CS is used for the transport of packet based protocols
which inclide:
1. IEEE Std 802.3(Ethernet)
2. IEEE Std 802.1Q(VLAN)
3. Internet Protocol (IPv4 and IPv6)
The service specific CS resides on top of the MAC Common Part
Sublayer (CPS). The service specific CS is responsible for:
o accepting packets (PDUs) from the upper layer,
o performing classification of the packet/PDU based on a set of
classifiers that are defined which are service specific,
o delivering the CS PDU to theappropriate service flow and transport
connection and,
o receiving PDUs from the peer entity.
Payload header suppression (PHS) is also a function of the CS but is
optional.
The figure below shows the concept of the service-specific CS in
relation to the MAC:
-----------------------------\
| ATM CS | Packet CS | \
----------------------------- \
| MAC Common Part Sublayer | \
| (Ranging, scheduling, etc)| 802.16 MAC
----------------------------- /
| Security | /
|(Auth, encryption,key mgmt)| /
-----------------------------/
| PHY |
-----------------------------
Figure 1: The 802.16 MAC
Patil, et al. Expires June 7, 2007 [Page 5]
Internet-Draft IPv6 over Packet CS in 802.16 December 2006
Classifiers for each of the specific upper-layer protocols, i.e
Ethernet, VLAN and IP, are defined which enable the packets from the
upper layer to be processed by the appropriate service-specific part
of the packet CS. IPv6 can be transported directly over the IP
specific part of the packet CS or over 802.3/Ethernet (which in turn
is handled by the Ethernet specific part of the packet CS) or over
802.1Q (which is handled by the 802.1Q specific part of the packet
CS).
The figure below shows the options for IPv6 transport over the packet
CS of 802.16:
----------------- -----------------
| IPv6 | | IPv6 |
---------------- |---------------| |----------- |
| IPv6 | | Ethernet | | 802.1Q |
|--------------| |---------------| |----------- |
| IP Specific | | 802.3 specific| |802.1Q specific|
|part of Pkt CS| |part of Pkt CS | |part of Pkt CS |
|..............| |...............| |...............|
| MAC | | MAC | | MAC |
|--------------| |---------------| |---------------|
| PHY | | PHY | | PHY |
---------------- ----------------- -----------------
(1) IPv6 over (2) IPv6 over (3) IPv6 over
IP Specific part 802.3/Ethernet 802.1Q
of Packet CS
Figure 2: IPv6 over IP, 802.3 and 802.1Q specific parts of the Packet
CS
The scope of this document is limited to IPv6 operation over the IP
specific part of the Packet CS only. It should be noted that while
capability exchange of the MS and BS is performed, there is no
negotiation of which service specific part of the packet CS will be
used for IPv6 transport.
4.1. IPv6 encapsulation over the IP CS of the MAC
The IPv6 payload when carried over the IP specfic part of the Packet
CS is encapsulated by the 6 byte 802.16 MAC header. Header
suppression can also be applied to the IP packet. The format of the
IPv6 packet with and without header suppression is shown in the
Patil, et al. Expires June 7, 2007 [Page 6]
Internet-Draft IPv6 over Packet CS in 802.16 December 2006
figure below:
---------/ /-----------
| MAC SDU |
--------/ /------------
||
||
\/
---------------------------------------------------------
| PHSI=0 | IPv6 Packet (including Header) |
---------------------------------------------------------
(i) IPv6 packet without header suppression
---------------------------------------------------------
| PHSI=1 | (Header suppressed IPv6 packet) |
---------------------------------------------------------
(ii) IPv6 packet with header suppression
Figure 3: IPv6 encapsulation
The IP classifiers that are used at the MAC operate on the fields of
the IP header and the transport protocol and these include the IP
ToS/DSCP, IP Protocol field, Masked IP source and destination
addresses and, Protocol source and destination port ranges. Using
the classifiers, the MAC maps an upper layer packet to a specific
service flow and transport connection to be used.
5. Generic network architecture using the 802.16 air interface
In a network that utilizes the 802.16 air interface the host/MS is
attached to an IPv6 access router (AR) in the network. The BS is a
layer 2 entity only. The AR can be an integral part of the BS or the
AR could be an entity beyond the BS within the access network. IPv6
packets between the MS and BS are carried over a point-to-point
transport connection which has a unique connection identifier (CID).
The transport connection is a MAC layer link between the MS and the
BS. The figures below describe the possible network architectures
and are generic in nature. More esoteric architectures are possible
but not considered in the scope of this document. Option A:
Patil, et al. Expires June 7, 2007 [Page 7]
Internet-Draft IPv6 over Packet CS in 802.16 December 2006
+-----+ CID1 +--------------+
| MS1 |------------/| BS/AR |-----[Internet]
+-----+ / +--------------+
. /---/
. CIDn
+-----+ /
| MSn |---/
+-----+
Figure 4: The IPv6 AR as an integral part of the BS
Option B:
+-----+ CID1 +-----+ +-----------+
| MS1 |----------/| BS1 |----------| AR |-----[Internet]
+-----+ / +-----+ +-----------+
. / ____________
. CIDn / ()__________()
+-----+ / L2 Tunnel
| MSn |-----/
+-----+
Figure 5: The IPv6 AR is separate from the BS, which acts as a bridge
The above network models serve as examples and are shown to
illustrate the point to point link between the MS and the AR. The
next section shows a realization of the generic architecture by the
WiMAX forum.
5.1. WiMAX network architecture and IPv6 support
The WiMAX network architecture consists of the Access Service Network
(ASN) and the Connectivity Service Network (CSN). The ASN is the
access network which includes the BS and the AR in addition to other
functions such as AAA, Mobile IP Foreign agent, Paging controller,
Location Register etc. The CSN is the entity that provides
connectivity to the Internet and includes functions such as Mobile IP
Home agent and AAA. The figure below shows the WiMAX reference
model:
Patil, et al. Expires June 7, 2007 [Page 8]
Internet-Draft IPv6 over Packet CS in 802.16 December 2006
-------------------
| ---- ASN | |----|
---- | |BS|\ R6 -------| |---------| | CSN|
|MS|-----R1----| ---- \---|ASN-GW| R3 | CSN | R5 | |
---- | |R8 /--|------|----| |-----|Home|
| ---- / | | visited| | NSP|
| |BS|/ | | NSP | | |
| ---- | |---------| | |
| NAP | \ |----|
------------------- \---| /
| | /
| (--|------/----)
|R4 ( )
| ( ASP network )
--------- ( or Internet )
| ASN | ( )
--------- (----------)
Figure 6: WiMAX Network reference model
Three different types of ASN realizations called profiles are defined
by the architecture. ASNs of profile types A and C include BS' and
ASN-gateway(s) (ASN-GW) which are connected to each other via an R6
interface. An ASN of profile type B is one in which the
functionality of the BS and other ASN functions are merged together.
No ASN-GW is specifically defined in a profile B ASN. The absence of
the R6 interface is also a profile B specific characteristic. The MS
at the IPv6 layer is associated with the AR in the ASN. The AR may
be a function of the ASN-GW in the case of profiles A and C and is a
function in the ASN in the case of profile B. When the BS and the AR
are separate entities and linked via the R6 interface, IPv6 packets
between the BS and the AR are carried over a GRE tunnel. The
granularity of the GRE tunnel should be on a per MS basis or on a per
service flow basis (an MS can have multiple service flows, each of
which are identified uniquely by a service flow ID). The protocol
stack in WiMAX for IPv6 is shown below:
Patil, et al. Expires June 7, 2007 [Page 9]
Internet-Draft IPv6 over Packet CS in 802.16 December 2006
|-------|
| App |- - - - - - - - - - - - - - - - - - - - - - - -(to app peer)
| |
|-------| /------ -------
| | / IPv6 | | |
| IPv6 |- - - - - - - - - - - - - - - - / | | |-->
| | --------------- -------/ | | IPv6|
|-------| | \Relay/ | | | |- - - | |
| | | \ / | | GRE | | | |
| | | \ /GRE | - | | | | |
| |- - - | |-----| |------| | | |
| IPv6CS| |IPv6CS | IP | - | IP | | | |
| ..... | |...... |-----| |------|--------| |-----|
| MAC | | MAC | L2 | - | L2 | L2 |- - - | L2 |
|-------| |------ |-----| |----- |--------| |-----|
| PHY |- - - | PHY | L1 | - | L1 | L1 |- - - | L1 |
-------- --------------- ----------------- -------
MS BS AR/ASN-GW CSN Rtr
Figure 7: WiMAX protocol stack
As can be seen from the protocol stack description, the IPv6 end-
points are constituted in the MS and the AR. The BS provides lower
layer connectivity for the IPv6 link.
6. IPv6 link
RFC 2461 defines link as a communication facility or medium over
which nodes can communicate at the link layer, i.e., the layer
immediately below IP [RFC2461]. A link is bounded by routers that
decrement TTL. When an MS moves within a link, it can keep using its
IP addresses. This is a layer 3 definition and note that the
definition is not identical with the definition of the term '(L2)
link' in IEEE 802 standards. This section presents a model for the
last mile link, i.e. the link to which MSs attach themselves.
6.1. IPv6 link in 802.16
In 802.16, there exists L2 Transport Connection between an MS and a
BS over which packets are transferred. A Transport Connection is
represented by CID (Connection Identifier) and multiple Transport
Connections can be assigned to an MS.
When an AR and a BS are collocated, the collection of Transport
Patil, et al. Expires June 7, 2007 [Page 10]
Internet-Draft IPv6 over Packet CS in 802.16 December 2006
Connections to an MS is defined as a single link. When an AR and a
BS are separated, it is recommended that a tunnel is established
between the AR and a BS whose granuality is no greater than 'per MS'
or 'per service flow' ( An MS can have multiple service flows which
are identified by a service flow ID). Then the tunnel(s) for an MS,
in combination with the MS's Transport connections, forms a single
point-to-point link. Hence the point-to-point link model for IPv6
operation over the IP specific part of the Packet CS in 802.16 is
recommended. A unique IPv6 prefix(es) per link (MS) is also
recommended.
6.1.1. IPv6 link in WiMAX
WiMAX is an example of a network based on the IEEE Std 802.16 air
interface. This section describes the IPv6 link in the context of a
WiMAX network. The MS and the AR are connected via a combination of
:
1. The transport connection which is identified by a Connection
Identifier (CID) over the air interface, i.e the MS and BS and,
2. A GRE tunnel between the BS and AR which transports the IPv6
packets
From an IPv6 perspective the MS and the AR are connected by a point-
to-point link. The combination of transport connection over the air
interface and the GRE tunnel between the BS and AR creates a (point-
to-point) tunnel at the layer below IPv6.
The collection of service flows (tunnels) to an MS is defined as a
single link. Each link has only an MS and an AR. Each MS belongs to
a different link. No two MSs belong to the same link. A different
prefix should be assigned to each unique link. This link is fully
consistent with a standard IP link, without exception and conforms
with the definition of a point-to-point link in RFC2461 [RFC2461].
6.2. IPv6 link establishment in 802.16
In order to enable the sending and receiving of IPv6 packets between
the MS and the AR, the link between the MS and the AR via the BS
needs to be established. This section illustrates the link
establishment procedure.
The MS goes through the network entry procedure as specified by
802.16. A high level description of the network entry procedure is
as follows:
Patil, et al. Expires June 7, 2007 [Page 11]
Internet-Draft IPv6 over Packet CS in 802.16 December 2006
1. MS performs initial ranging with the BS. Ranging is a process by
which an MS becomes time aligned with the BS. The MS is
synchronized with the BS at the succesful completion of ranging
and is ready to setup a connection.
2. MS and BS perform capability exchange as per 802.16 procedures.
The CS capability parameter indicates which classification/PHS
options and SDU encapsulation the MS supports. By default,
Packet, IPv4 and 802.3/Ethernet shall be supported, thus absence
of this parameter in REG-REQ (802.16 message) means that named
options are supported by the MS/SS. Support for IPv6 over the IP
specific part of the packet CS is indicated by Bit#2 of the CS
capability parameter (Refer to [802.16e]).
3. The MS progresses to an authentication phase. Authentication is
based on PKMv2 as defined in the IEEE Std 802.16 specification.
4. On succesfull completion of authentication, the MS performs
802.16 registration with the network.
5. The MS can request the establishment of a service flow for IPv6
packets over the IP specific part of the Packet CS. The service
flow can also be triggered by the network as a result of pre-
provisioning. The service flow establishes a link between the MS
and the AR over which IPv6 packets can be sent and received.
6. The AR sends a router advertisement to the MS. Alternatively or
in addition, the MS can also send a router solicitation.
The above flow does not show the actual 802.16 messages that are used
for ranging, capability exchange or service flow establishment.
Details of these are in [802.16e].
6.2.1. IPv6 link establishment in WiMAX
The mobile station performs initial network entry as specified in
802.16. On succesful completion of the network entry procedure the
ASN gateway/AR triggers the establishment of the initial service flow
(ISF) for IPv6 towards the MS. The ISF is a GRE tunnel between the
ASN-GW/AR and the BS. The BS in turn requests the MS to establish a
transport connection over the air interface. The end result is a
transport connection over the air interface for carrying IPv6 packets
and a GRE tunnel between the BS and AR for relaying the IPv6 packets.
On succesful completion of the establishment of the ISF, IPv6 packets
can be sent and received between the MS and AR. The ISF enables the
MS to communicate with the AR for host configuration procedures.
After the establishment of the ISF, the AR can send a router
advertisement to the MS. An MS can establish multiple service flows
with different QoS characteristics. The ISF can be considered as the
primary service flow. The ASN-GW/ AR treats each ISF, along with the
other service flows to the same MS, as a unique link which is managed
as a (virtual) interface.
Patil, et al. Expires June 7, 2007 [Page 12]
Internet-Draft IPv6 over Packet CS in 802.16 December 2006
6.3. Maximum transmission unit in 802.16
The MAC HDR is a 6 byte header followed by the payload and a 4 byte
CRC which covers the whole PDU. The length of the PDU is indicated
by the Len parameter in the Generic MAC HDR. The Len parameter has a
size of 11 bits. Hence the total PDU size is 2048 bytes. The IPv6
payload can be a max value of 2038 bytes (MAC HDR - CRC). The Max
value of the IPv6 MTU for 802.16 is 2038 bytes and the minimum value
of 1280 bytes. RFC2461 defines an MTU option that an AR can
advertise to an MN. If an AR advertises an MTU via the RA MTU
option, the MN should use the MTU from the RA.
6.3.1. Maximum transmission unit in WiMAX
The WiMAX forum [WMF] has specified the Max SDU size as 1522 octets.
Hence the IPv6 path MTU can be 1500 octets. However because of the
overhead of the GRE tunnel used to transport IPv6 packets between the
BS and AR and the 6 byte MAC header over the air interface, using a
value of 1500 would result in fragmentation of packets. It is
recommended that the default MTU for IPv6 be set to 1400 octets for
the MS in WiMAX networks. Note that the 1522 octet specification is
a WiMAX forum specification and not the size of the SDU that can be
transmitted over 802.16, which is higher.
7. IPv6 prefix assignment
Each MS can be considered to be on a separate subnet as a result of
the point-to-point connection. A CPE type of device which serves
multiple IPv6 hosts, may be the end point of the connection. Hence
one or more /64 prefixes should be assigned to a link. The prefixes
are advertised with the on-link (L-bit) flag set to facilitate
Detecting Network Attachment (DNA) operation [RFC4135].
8. Router Discovery
8.1. Router Solicitation
On completion of the establishment of the IPv6 link, the MS may send
a router solicitation message to solicit a Router Advertisement
message from the AR to acquire necessary information as specified in
RFC2461 [RFC2461]. An MS that is network attached may also send
router solicitations at any time.
Patil, et al. Expires June 7, 2007 [Page 13]
Internet-Draft IPv6 over Packet CS in 802.16 December 2006
8.2. Router Advertisement
The AR should send a number (configurable value) of router
advertisements as soon as the IPv6 link is established, to the MS.
The AR sends unsolicited router advertisements periodically as
specified in RFC2461 [RFC2461].
8.3. Router lifetime and periodic router advertisements
The router lifetime should be set to a large value, preferably in
hours. This document over-rides the specification for the value of
the router lifetime in RFC2461 [RFC2461]. The AdvDefaultLifetime in
the router advertisement MUST be either zero or between
MaxRtrAdvInterval and 43200 seconds. The default value is 2 *
MaxRtrAdvInterval.
802.16 hosts have the capability to transition to an idle mode in
which case the radio link between the BS and MS is torn down. Paging
is required in case the network needs to deliver packets to the MS.
In order to avoid waking a mobile which is in idle mode and consuming
resources on the air interface, the interval between periodic router
advertisements should be set quite high. The MaxRtrAdvInterval value
specified in this document over-rides the recommendation in RFC2461
[RFC2461]. The MaxRtrAdvInterval MUST be no less than 4 seconds and
no greater than 21600 seconds. Thee default value for
MaxRtrAdvInterval is 10800 seconds.
9. IPv6 addressing for hosts
The addressing scheme for IPv6 hosts in 802.16 network follows the
IETFs recommendation for hosts specified in RFC 4294. The IPv6 node
requirements RFC RFC4294 [RFC4294] specifies a set of RFCs that are
applicable for addressing.
9.1. Interface Identifier
The MS has a 48-bit MAC address as specified in 802.16e [802.16e].
This MAC address is used to generate the 64 bit interface identifier
which is used by the MS for address autoconfiguration. The IID is
generated by the MS as specified in RFC2464 [RFC2464]. For addresses
that are based on privacy extensions, the MS may generate random IIDs
as specified in RFC3041 [RFC3041].
9.2. Duplicate address detection
DAD is performed as per RFC2461 [RFC2461] and, RFC2462 [RFC2462].
Patil, et al. Expires June 7, 2007 [Page 14]
Internet-Draft IPv6 over Packet CS in 802.16 December 2006
9.3. Stateless address autoconfiguration
If the A-bit in the prefix information option (PIO) is set, the MS
performs stateless address autoconfiguration as per RFC 2461, 2462.
The AR is the default router that advertises a unique /64 prefix (or
prefixes) that is used by the MS to configure an address.
9.4. Stateful address autoconfiguration
The Stateful Address Autoconfiguration is invoked if the M-flag is
set in the Router Advertisement. Obtaining the IPv6 address through
stateful address autoconfiguration method is specified in RFC3315
[RFC3315].
10. IANA Considerations
This draft does not require any actions from IANA.
11. Security Considerations
This document does not introduce any new vulnerabilities to IPv6
specifications or operation as a result of the 802.16 air interface
or the WiMAX network architecture.
12. Acknowledgments
TBD.
13. References
13.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", RFC 2119, March 1997,
<ftp://ftp.isi.edu/in-notes/rfc2119>.
[RFC2461] Narten, T., Nordmark, E., and W. Simpson, "Neighbor
Discovery for IP Version 6 (IPv6)", RFC 2461,
December 1998, <ftp://ftp.isi.edu/in-notes/rfc2461>.
[RFC2462] Thomson, S. and T. Narten, "IPv6 Stateless Address
Autoconfiguration", RFC 2462, December 1998,
<ftp://ftp.isi.edu/in-notes/rfc2462>.
Patil, et al. Expires June 7, 2007 [Page 15]
Internet-Draft IPv6 over Packet CS in 802.16 December 2006
[RFC2464] Crawford, M., "Transmission of IPv6 Packets over Ethernet
Networks", RFC 2464, December 1998,
<ftp://ftp.isi.edu/in-notes/rfc2464>.
[RFC3041] Narten, T. and R. Draves, "Privacy Extensions for
Stateless Address Autoconfiguration in IPv6", RFC 3041,
January 2001, <ftp://ftp.isi.edu/in-notes/rfc3041>.
[RFC3314] Wasserman, Ed., M., "Recommendations for IPv6 in Third
Generation Partnership Project (3GPP) Standards",
RFC 3314, September 2002,
<ftp://ftp.isi.edu/in-notes/rfc3314>.
[RFC3315] Droms, Ed., R., Bound, J., Volz, B., Lemon, T., Perkins,
C., and M. Carney, "Dynamic Host Configuration Protocol
for IPv6 (DHCPv6)", RFC 3315, July 2003,
<ftp://ftp.isi.edu/in-notes/rfc3315>.
[RFC3756] Nikander, P., Kempf, J., and E. Nordmark, "IPv6 Neighbor
Discovery (ND) Trust Models and Threats", RFC 3756,
May 2004, <ftp://ftp.isi.edu/in-notes/rfc3756 >.
[RFC4135] Choi, JH. and G. Daley, "Goals of Detecting Network
Attachment in IPv6", RFC 4135, August 2005,
<ftp://ftp.isi.edu/in-notes/rfc4135>.
[RFC4294] Loughney, Ed., J., "IPv6 Node requirements", RFC 4294,
April 2006, <ftp://ftp.isi.edu/in-notes/rfc4294>.
[RFC4921] Hinden, R. and S. Deering, "IP Version 6 Addressing
Architecture", RFC 4921, February 2006,
<ftp://ftp.isi.edu/in-notes/rfc4291>.
13.2. Informative References
[802.16e] "IEEE Std 802.16e: IEEE Standard for Local and
metropolitan area networks, Amendment for Physical and
Medium Access Control Layers for Combined Fixed and Mobile
Operation in Licensed Bands", October 2005.
[FRD] Choi, JH., Shin, DongYun., and W. Haddad, "Fast Router
Discovery with L2 support", August 2006, <http://
www.ietf.org/internet-drafts/draft-ietf-dna-frd-02.txt>.
[PSDOC] Jee, J., "IP over 802.16 Problem Statement and Goals",
October 2006, <http://www.ietf.org/internet-drafts/
draft-ietf-16ng-ps-goals-00.txt>.
Patil, et al. Expires June 7, 2007 [Page 16]
Internet-Draft IPv6 over Packet CS in 802.16 December 2006
[WMF] "http://www.wimaxforum.org".
[WiMAXArch]
"WiMAX End-to-End Network Systems Architecture
http://www.wimaxforum.org/technology/documents",
August 2006.
Authors' Addresses
Basavaraj Patil
Nokia
6000 Connection Drive
Irving, TX 75039
USA
Email: basavaraj.patil@nokia.com
Frank Xia
Huawei USA
1700 Alma Dr. Suite 100
Plano, TX 75075
Email: xiayangsong@huawei.com
Behcet Sarikaya
Huawei USA
1700 Alma Dr. Suite 100
Plano, TX 75075
Email: sarikaya@ieee.org
JinHyeock Choi
Samsung AIT
Networking Technology Lab
P.O.Box 111
Suwon, Korea 440-600
Email: jinchoe@samsung.com
Patil, et al. Expires June 7, 2007 [Page 17]
Internet-Draft IPv6 over Packet CS in 802.16 December 2006
Syam Madanapalli
LogicaCMG
125 Yemlur P.O.
Off Airport Road
Bangalore, India 560037
Email: smadanapalli@gmail.com
Patil, et al. Expires June 7, 2007 [Page 18]
Internet-Draft IPv6 over Packet CS in 802.16 December 2006
Full Copyright Statement
Copyright (C) The Internet Society (2006).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgment
Funding for the RFC Editor function is provided by the IETF
Administrative Support Activity (IASA).
Patil, et al. Expires June 7, 2007 [Page 19]
| PAFTECH AB 2003-2026 | 2026-04-24 12:32:08 |