One document matched: draft-hares-asconfed-edge-02.txt
Differences from draft-hares-asconfed-edge-01.txt
IDR Working Group S. Hares
Internet-Draft NextHop Technologies
Expires: April 19, 2006 P. Bose
Lockheed
October 16, 2005
Dynamic AS Re-Association At Confederation Edge
draft-hares-asconfed-edge-02.txt
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on April 19, 2006.
Copyright Notice
Copyright (C) The Internet Society (2005).
Abstract
This document provides a mechanism for Autonomous Systems within an
AS Confederation to survive the disconnection to other AS within the
AS confederation without dropping peers. When all links to the other
AS in the Confederation break, this mechanism allows the AS to revert
to local AS to continue communication with E-BGP peers. This
mechanism has two parts: Capability signaling between the two parties
at connection start to save two AS (internal and AS Confederation AS)
Hares & Bose Expires April 19, 2006 [Page 1]
Internet-Draft DYNAS-Confed-Edge October 2005
and a mechanism to signal the switch between AS Confederation AS and
internal AS.
Table of Contents
1. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Conventions used in this document . . . . . . . . . . . . 3
2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Mechanism overview for Dynamic AS Confederation Edge
Re-association . . . . . . . . . . . . . . . . . . . . . . . . 5
4. BGP Peer mechanisms . . . . . . . . . . . . . . . . . . . . . 7
5. Open Dynamic AS Capability . . . . . . . . . . . . . . . . . . 11
6. Capability Message . . . . . . . . . . . . . . . . . . . . . . 13
7. Prevention of Loops . . . . . . . . . . . . . . . . . . . . . 15
8. Security Considerations . . . . . . . . . . . . . . . . . . . 21
9. References . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 22
Intellectual Property and Copyright Statements . . . . . . . . . . 23
Hares & Bose Expires April 19, 2006 [Page 2]
Internet-Draft DYNAS-Confed-Edge October 2005
1. Definitions
1.1. Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [1].
Hares & Bose Expires April 19, 2006 [Page 3]
Internet-Draft DYNAS-Confed-Edge October 2005
2. Introduction
This mechanism provides a mechanism for an Autonomous System within
an AS confederation to survive disconnection from the rest of the
Autonomous Systems within the AS Confederation. When an AS is
connected to the rest of an AS confederation, it acts as a single AS.
If all links between the AS to other members of the AS confederation
are broken, the AS Confederation is broken in two (or more) parts,
and the individual sub-Autonomous Systems (sub-AS-es) within the
confederation may need to "back off" to their local AS number to
restore connectivity through some external path.
Upon return of the AS Confederation links, this mechanism can signal
the Edge AS returning to the AS Confederation.
Hares & Bose Expires April 19, 2006 [Page 4]
Internet-Draft DYNAS-Confed-Edge October 2005
3. Mechanism overview for Dynamic AS Confederation Edge Re-association
The mechanism has parts: Open Capability and Dynamic Capability.
1) An Dynamic AS-Confederation Edge Open capability
The AS-Confederation capability signals the ability to fail-over upon
"AS confederation disconnect" by changing the local AS number without
resetting the eBGP peering session.
The format of the ASConfed-Edge capability is described in section 4
and contains the AS of the Confederation and a list of Internal AS
that the BGP peer will back off to. This capability also indicates
the mechanism by which the node will signal the switch via the
dynamic capabilities.
Note: The detection of the "AS confederation disconnect" is a locally
determined feature that includes (but is not limited to): determining
that all AS Confederation BGP peers are disconnected from this peer.
2) Dynamic Capablity - Signaling AS Fail-over and Restoration
2.1)Signaling the AS Fail-over to Internal AS
Signaling an AS fail-over is done via a dynamic capability with
the ASConfed_Edge capability with AS flag on. The
ASConfed_Edge dynamic capability requires a dynamic capability
with an "ACK" be sent to the originating BGP peer. Whether the
"ACK" signals a success or failure, the full ASConfed_Edge
capability must be sent.
The AS peer wishing to switch from an AS confederation to an
internal AS, signals this to a peer by sending a ASConfed_Edge
dynamic capability with the AS-in-Use flag set to the internal
AS.
Upon receiving this dynamic capability the BGP speaker
associated with the AS-Confederation Edge switches from the AS
confederation to the AS number specified for the session to the
internal session.
After switching to the new AS:
All checking of the local AS in BGP packets utilizes the new
AS.
-All new routes will be announced with the new AS number.
Hares & Bose Expires April 19, 2006 [Page 5]
Internet-Draft DYNAS-Confed-Edge October 2005
-All older routes will be re-announced based on the AS
resend flag.
2.2) Signaling a AS restoring to AS confederations
When the AS Confederations links are re-established, the BGP
speaker on the AS Confederation sends a Dynamic Capability with
the ASConfed_Edge Capability with "AS in Use flag" set AS
Confederation flag. All AS checking for the local BGP speaker
reverts to the original Confederation AS.
After switching back to the AS Confederation:
-All Checking of the local AS in BGP packets utilizes the AS
Confederation number.
-All new routes will be announced with the AS confederation
number
All older routes will be re-announced with the AS
confederation number based on the AS resend flag.
Hares & Bose Expires April 19, 2006 [Page 6]
Internet-Draft DYNAS-Confed-Edge October 2005
4. BGP Peer mechanisms
The mechanism has two parts:
1) Negotiate Open Capability with AS Confederation Edge
The ASConfed-Edge capability signals that a BGP peer ability to
use the Dynamic AS Dynamic-Capability exchange on an AS
Confederation Edge.
The format of the ASConfed-Edge capability is described in section
5 and contains a list of Autonomous systems that the BGP peer may
re-associated to. This capability also indicates the mechanism by
which the node will signal the switch is the dynamic capabilities
message. The resend flags indicated in the type of resend flags
the peer will support.
Within an AS, any BGP peer that will send an ASConfed-Edge
Capability to an Exterior peer MUST send the ASConfed-Edge
capability to all IBGP peers. Only if all IBGP Peers successfully
negotiated the ASConfed-Edge capability, can any BGP peer
dynamically switch over from the AS Confederation to an internal
AS using this mechanism.
2) Signaling the Dynamic AS Confederation Switch -Originator
Signaling a Dynamic Switch is done via the Dynamic Capability
message DYN-CAP [3] with the Dynamic AS capability (format in
section 6).
The BGP peer decides to initiate the AS switch over by using local
policy and implementation specific mechanisms. To signal the
Dynamic AS switch over, the initiating BGP peer has two steps.
Step 1: Dynamic AS Confederation AS change to all IBGP peers
Upon receiving a "Dynamic AS Confederation change" indication
to the BGP process, the BGP process will send to IBGP peers a
dynamic capability message with Dynamic AS Confed_Edge
capability with flags of:
Source flag to IBGP
AS use set to either InternalAS /AS Confederation
Reserve/Start set to reserve
Hares & Bose Expires April 19, 2006 [Page 7]
Internet-Draft DYNAS-Confed-Edge October 2005
Success flag set to Success (0) and,
Resend flags set to peers desired resend capability
If the Dynamic AS Confederation is switching from the AS
Confederation to the internal peer, the flag is set to internal
peer. If peer is requesting a switch from the internal AS to
the AS Confederation, the flag is set to AS Confederation
Upon receiving the ACK from all IBGP peers for the Dynamic AS
Capability,the BGP peer will send a capability message with the
AS Confed_EDGE capability with flags set to:
source flag to IBGP,
the AS use set to InternalAS/AS Confederation,
Reserve/Start set to Start,
Success/Failure byte - set to Success, and
resend flags set to peers desired resend capability.
Upon receiving an ACK from all IBGP peers for the dynamic AS
Confed_EDGE capability with start step 2.
In case of the receiving IBGP peer's local BGP implementation
detecting a failure to switch to a new AS when it receives the
dynamic capability with the "Reserve" flag set, Capability will
be signaled with a "failure" flag. This failure will halt the
originating Peer switch to the new AS. The failure is signaled
by responding to the Dynamic ASConfed_Edge dynamic capability
with the following bits set:
source flag set to IBGP
AS use flags set to internal/AS confederation,
Reserve/Start set to reserve,
resend flags set to original resend
If the IBGP peers are part of a Route-Reflection hierarchy, a
Route Reflector MUST wait to send an ack to the Dynamic AS
change after it has signaled all of its clients and all of it
total mesh peers. In this way, when the initiating IBGP peer
receives the Dynamic Capability ACK, the rest of the IBGP peer
has been informed.
Hares & Bose Expires April 19, 2006 [Page 8]
Internet-Draft DYNAS-Confed-Edge October 2005
Note: that the Dynamic Capability ACK may pass back success or
failure. A failure anywhere in an IBGP cloud will not allow
the BGP to progress to step 2. Each AS Confed_Edge capability
MUST be responded to with an dynamic capability with an ACK.
Step 2: Send all EBGP peers the Dynamic AS Confederation Change
Each EBGP peers signal the Dynamic AS change to its neighbor
with ASConfed_EDGE Dynamic Capability. When sent to an EBGP
peer, the source flag is set to "EBGP" flag.
Upon receiving this dynamic capability from an E-BGP peer, the
BGP speaker processes the switch of the peer from the current
AS number to the one specified in the capability. This change
in processing includes:
-All checking of the local AS in BGP packets utilizes the
new AS.
-All new routes will be announced with the new AS number.
-All older routes will be re-announced based on the AS
resend flag.
Upon successful processing, the EBGP peer will acknowledge the
Dynamic AS capability by sending a Dynamic Capability with an
Ack in the Dynamic Capability flag and an "ack-succeess"
indication in the Dynamic Capabiity flag word.
3) E-BGP Peer Receiving a Signaling the Dynamic AS Switch-over
Upon receiving a "Dynamic AS Change" Dynamic capability from an EBGP
peer, the EBGP peer will follow 2 steps:
Step 1: Upon receiving a Dynamic AS Confed_Edge capability the BGP
process will send to all IBGP peers the Dynamic AS Confed_Edge
dynamic capability with an the as switch over flags.
Upon receiving the Dynamic Capability with the "Ack" bit set
from all IBGP peers for the Dynamic ASConfed_EDGE Capability,
the BGP peer can start step 2.
Again, if the IBGP peers of the receiving BGP are part of a
Route-Reflection hierarchy, a Route Reflector MUST only send an
ACK to the Dynamic AS Confed_Edge change after it has
successfully sent the Dynamic Capability to its clients and all
of it total mesh peers. In this way, when the initiating IBGP
peer receives the Dynamic capability ACK, the rest of the IBGP
Hares & Bose Expires April 19, 2006 [Page 9]
Internet-Draft DYNAS-Confed-Edge October 2005
peer has been informed.
In case of errors in resetting the Dynamic AS capability, the
receiving IBGP peer can set the "Failure" flag in the Dynamic
capability that is being ACK. Any failures will be signaled to
the originating AS, and the Dynamic AS switch terminated.
Termination of the AS_confederation switch can be done by
deleting the Dynamic AS_Confederation capability
Step 2: Respond to E-BGP AS with Dynamic AS change
The E-BGP peer responds to the originated AS with a Dynamic AS
change with an EBGP flag set and the Failure bit off.
Upon receiving this dynamic capability from an E-BGP peer, the
BGP speaker associated with the AS Edge process the switch of
the peer from the current AS number to the one specified in the
capability. This switch includes:
-All checking of the local AS in BGP packets utilizes the
new AS.
-All new routes will be announced with the new AS number.
-All older routes will be re-announced based on the AS
resend flag.
Hares & Bose Expires April 19, 2006 [Page 10]
Internet-Draft DYNAS-Confed-Edge October 2005
5. Open Dynamic AS Capability
RFC 3992 [2] describes the open capability mechanisms. This document
describes a new Capability: Dynamic ASConfeder_EDGE.
+------------------------------+
| Capability Code (1 octet) |
+------------------------------+
| Capability Length (1 octet) |
+------------------------------+
| Capability Value (variable) |
+------------------------------+
Where the Capability value is:
+------------------------------+
| Length of AS (1 octet) | - length of AS field (2 or 4)
+------------------------------+
| Reserved (5 bits) | - Reserved
+------------------------------+
| resend prefix flag (3 bits) | - Resend/AS Flag
--------------------------------
| Number of AS supported | - # of AS in re-associate list
| (1 octet) |
+------------------------------+
| AS confederation | - AS Confederation number
+------------------------------+
| internal AS number | - AS 1 dynamic re-association
+------------------------------+
Figure 1: Dynamic AS Confederation Edge Open Capability Bytes
The resend prefix flag indicates when the AS will resend the routes
with the new AS. The flag values are set as a bit pattern to
indicate that
0x00 - Resend routes based on local timer (in bataches)
0x01 - Resend routes immediately
0x02 - Don't resend routes (leave with old AS confederation)
The number of AS supported field gives the number of the Autonomous
Systems fin the dynamic re-association list.The Autonomous Systems in
the AS list are the list of ASes that this peer may switch to in when
Hares & Bose Expires April 19, 2006 [Page 11]
Internet-Draft DYNAS-Confed-Edge October 2005
dynamically re-association from the original AS to a new AS.
Each side of the peer will send a list of Autonomous Systems that it
will dynamic re-associate with. Upon start-up the re-associations
list can be check by policy to determine that each side can support
the required re-associations.
Hares & Bose Expires April 19, 2006 [Page 12]
Internet-Draft DYNAS-Confed-Edge October 2005
6. Capability Message
This BGP dynamic capability uses the new BGP Dynamic Capability DYN-
CAP [3] format of:
+------------------------------+
| Init/Ack (1 bit) |
+------------------------------+
| Ack Request (1 bit) |
+------------------------------+
| Reserved (5 bits) |
+------------------------------+
| Action (1 bit) |
+------------------------------+
| Sequence Number (4 octets) |
+------------------------------+
| Capability Code (1 octet) |
+------------------------------+
| Capability Length (2 octets) |
+------------------------------+
| Capability Value (variable) |
+------------------------------+
The capability value is:
+------------------------------+
| Length of AS | - Length of AS field
+------------------------------+
| Source (1 bits) | - Source flag
+------------------------------+
| Failure flag (1 bits) | - Resend/AS Flag
+------------------------------+
| Confed AS in Use (1 bit) | - Confederation AS in use
+------------------------------+
+ IBGP Reserve or Send + - Reserve/Start IBGP peers
+-------------------------------
| reserved (1 bits) | - Reserved
+------------------------------+
| resend prefix flag (3 bits) | - Resend/AS Flag
+------------------------------+
| Current AS number | - Old AS number
+------------------------------+
| New AS number | - new AS number
+------------------------------+
Hares & Bose Expires April 19, 2006 [Page 13]
Internet-Draft DYNAS-Confed-Edge October 2005
Source Flag flag (1 bits)
0 - node originated
1 - EBGP peer originated
Failiure Flag (1 bit)
1 - failure
0 - success
AS in USE:
0x0 - Internal AS number
0x1 - AS Confederation number
IBGP Reserve or Start
0x0 - Reserve IBGP peers only, Do not start EBGP peers
negotiation.
0x1 - Start IBGP peers and Start EBGP negotiation
Resend flag values
0x00 - Resend routes based on local timer
0x01 - Resend routes immediately
0x02 - Don't resend routes (leave with old AS confederation)
Hares & Bose Expires April 19, 2006 [Page 14]
Internet-Draft DYNAS-Confed-Edge October 2005
7. Prevention of Loops
Because all IBGP nodes are synchronized before an EBGP peer is
transition to a new AS, the local BGP logic can detect the full
transition.
If any active IBGP peer is unable to transition, the whole transition
to the new AS stops.
The two stages of IBGP negotation (IBGP only and EBGP/IBGP
negotiation) allow the peer to negotiated the ability to AS change
before information exterior peers. The two stage IBGP negotiation
can reduce or eliminate chatter to EBGP peers while the IBGP peers
settle on the decision to change the AS.
The two stage negotiation requires that IBGP peers deal with the
multiple AS identity that AS confederation nodes have. Each AS
confederation node has an internal AS and a Confederation Edge AS.
This section describes two scenarios of using the two stage process.
In the first scenario, the IBGP stage 1 synchronization fails. In
the second example, the IBGP Stage 1 synchronization succeeds.
In the example below, Node B, C, D an E are inside the AS
confederation. Nodes A and F are outside the AS confederation
(denoted as AS 200).
When node D is disconnected from Node C, the dynamic AS Confederation
Edge switch takes place. Node B, C, and E switch to AS 1000 for IBGP
and EBGP. Their split view of the world (AS 200/1000) becomes just
AS 1000. Node C detects the loss of the Connection to D, and sends
an indication to switch to the Internal AS.
Hares & Bose Expires April 19, 2006 [Page 15]
Internet-Draft DYNAS-Confed-Edge October 2005
+--------+ +-------------------+ +-------------------+ +-------+
+EBGP + + EBGP |IBGP Peer+ +IBGP peer| EBGP + +EBGP +
+outside +--+AS Confed|Internal + +Internal | inside + +inside +
+ confed + + AS 200 |AS 1000 +-|-+ AS 1000 | confed +-|-+Confed +
+ AS 300 + + | + | + | AS 1000 + +AS 2000+
+ + + | + | + | + + Node D +
+ + + | + | + |-------- + +-------+
+ A + + Node B + | + Node C | S 200 + +AS 200 +
+----|---+ +-------------------+ | +---------+------|--+ +--|----+
| | | |
| +---------------------+ +------------+ |
| |EBGP Peer | IBGP Peer| | EBGP peer +---
+-----------|AS Confed | AS 1000 | | outside +
| AS 200 | | | Confed +
| | | | AS 500 +
| Node E| | | Node F +
+---------------------+ +------------+
Figure 3: Dual AS identities for an IBGP with Dynamic AS
Confederation
Loop Prevention
1) Two stage commit in IBGP peers with failure
1. Node C's sends a Capability message to Node B with sequence
number 10 and an Add capability for Dynamic AS Confed_Edge
Capability. Inside the Dynamic AS Confed_Edge capability the
flags are set for: IBGP, Reserve and AS-in-Use Internal,
Success (always on request capability). The AS Confederation
is 200, and the Internal AS is 1000.
2. Node C's sends a Capability message to Node E with sequence
number 30 and an Add capability for Dynamic AS Confed_Edge
Capability. Inside the Dynamic AS Confed_Edge capability the
flags are set for: IBGP, Reserve and AS-in-Use Internal,
Success (always on request capability); the AS Confederation
is 200, and the Internal AS is 1000.
3. Node B trys to engage the AS 1000 switch but fails due to some
internal problem.
4. Node B sends a dynamic capability (seqence number 10) with an
ACK flag set and a Dynamic AS Confed_Edge capability inside
with flags set to: IBGP, Reserve, AS-in-Use Internal, Failure.
5. Node E successful can switch to the Internal AS. Node E sends
the capability message with an ACK flag, sequence number 30,
Hares & Bose Expires April 19, 2006 [Page 16]
Internet-Draft DYNAS-Confed-Edge October 2005
and an AS Confed_Edge capability inside. The flags inside the
AS Confed_Edge capability are set to: IBGP, Reserve, AS-In Use
Internal, and Success.
6. Node C sends sends a capability message to Node E with
sequence number 31, Delete flag, Dynamic AS Confed_Edge
capability with flag bits set to: IBGP, Reserve, AS-in-Use
Internal, and Failure.
7. Node E clears all Dynamic AS Confederation state and respond
with a capability messages with an "Ack" flag set, sequence
number 31, Delete Flag, Dynanic AS Confed_Edge capability with
flag bits set to:IBGP, Reserve, AS-in-Use Internal and
Failure.
8. Node C, B, and E form one portion of AS confederation 200, and
Node D forms another portion. (These loops are possible with
normal AS Confederations and the rejection by Node B stops the
Dynamic AS Confederation Edge from preventing the loops.
2) Two stage commit with IBGP peers with success
1. Node C's sends a Capability message to Node B with sequence
number 10 and an Add capability for Dynamic AS Confed_Edge
Capability. Inside the Dynamic AS Confed_Edge capability the
flags are set for: IBGP, Reserve and AS-in-Use Internal,
Success (always on request capability). Inside the Dynamic
AS Confed_Edge capability the AS Confederation is 200, and
the Internal AS is 1000.
2. Node C's sends a Capability message to Node E with sequence
number 30 and an Add capability for Dynamic AS Confed_Edge
Capability. Inside the Dynamic AS Confed_Edge capability the
flags are set for: IBGP, Reserve and AS-in-Use Internal,and
sucess. Success (always on request capability). Inside the
Dynamic AS Confed_Edge capability, the AS Confederation is
200, and the Internal AS is 1000.
3. Node B trys to engage the AS 1000 switch and succeeds. Node
B responds to Node C with a capability message with sequence
number 10, Ack Flag set, and a Dynamic AS Confed_Edge
caability inside. The Dynmic AS Confed_Edge capability has
flags set for: IBGP, Reserve, AS in-Use, and Success.
4. Node E successful can switch to the Internal AS. Node E
sends the capability message with an ACK flag, sequence
number 30, and an AS Confed_Edge capability inside. The
flags inside the AS Confed_Edge capability are set to: IBGP,
Hares & Bose Expires April 19, 2006 [Page 17]
Internet-Draft DYNAS-Confed-Edge October 2005
Reserve, AS-In Use Internal, and Success.
5. Node C's sends a capability message to Node B (seq 11) and
Node E (sequence 31) with an Add capability for Dynamic AS
Confed_Edge capability. Inside the Dynamic AS Confed_Edge
Capability,the flags are set to: IBGP, Reserve and AS-in-Use
Internal, Start, and Success (always on request capability).
AS 200 is in the AS confederation. AS 1000 is in the
internal AS.
6. Node B (sequence 11) sends back a capability messages with
ACK bit set on the Add of the Dynamic AS Confed_Edge
capability. Within the AS Confed_Edge capability, the flags
are set to: IBGP, Start, AS-in-Use Internal, and Success.
Node B starts to send capability mesages with Dynamic AS
Confed_Edge capability to the E-BGP peers.
1. Node B sends to Node A a capability message with Add of
Dynamic AS Confed_Edge capability with sequence number 5.
Inside the Dynamic AS Confed_Edge capability, the flags
are set to: EBGP, Start, AS-in-Use Internal, and Success.
2. Node A validates it can switch the E-BGP session to
receive AS 1000 from Node B. Node A sends back a
capability message with sequence number 5 with an ACK
flag set with an Internal AS Confed_Edge Capability
inside. Inside the AS Confed_Edge Capability the flags
are set to: EBGP, Start, AS-in-Use Internal and Success.
7. Node E sends node C a capability messages with sequence
number 31, Action Add and An Ack Flag set. The Dynamic AS
Confed_edge capabilty is contained inside with flags set to:
EBGP, Start, AS-in-Use Internal, and Success. Node E starts
to send capability messages with Dynamic AS Confed_Edge
capability to the E-BGP peers.
1. Node E sends to Node A a capability messages with
sequence number of 15. Action Add and a Dynamic AS
Confed_Edge capability inside. Inside the Dynamic AS
Confed_Edge capability the flags are set to: EBGP, Start,
AS-in-Use Internal,and Success.
2. Node A validates it can change the EBGP session to AS 300
to AS 1000, and then sends a capability to confirm the
Ack. The capability messages contains sequence number 15,
Add Action, Ack flag, and a Dynamic AS Confed_Edge
capability inside with flags of: EBGP, Start, AS-in-Use
Internal, and Success. Of course, the AS information is
Hares & Bose Expires April 19, 2006 [Page 18]
Internet-Draft DYNAS-Confed-Edge October 2005
AS Confederation 200, As Internal 1000.
8. After Node C sends the capability messages to it's internal
peers (Node E and Node B), it sends dynamic capabilities to
it's external peers: Node D (in the AS confederation) and
Node F (in AS 500 external to the AS Confederation.)
9. Node D processes C capability message
1. Node D receives a capability message from Node C with
sequence number 40, Add Action, and Dynamic AS
Confed_Edge capability inside. Inside the Dynamic AS
Confed_Edge capability the flags are set to: EBGP, Start,
AS-in-Use Internal, and Succcess. The AS information is
AS Confederation 200 and AS Internal 1000.
2. Node D determines it can switch the EBGP Session Node C
to AS 1000, the internal AS. It peers with AS 1000 as
the AS Confederation, and moves the AS value to 200.
3. Node D sends back an capability message with sequence
number 40, Add action, and Dynamic AS Confed_Edge
capability inside. Inside the Dynamic AS Confed_Edge
capability, the flags are set to: EBGP, Start, AS-in-Use
Internal and Success. The AS informaiton is AS
confederation 200 and AS internal 1000.
10. Node F process C's capability message
1. Node F receives a capability message from Node C with
sequence number 200, Add Action, and Dynamic AS
Confed_Edge capability inside. Inside the Dynamic AS
Confed_Edge capability the flags are set to: EBGP, Start,
AS-in-Use Internal, and Success. The AS information is:
AS Confederation 200 and AS Internal 1000.
2. Node F determines it can switch the EBGP session with
Node C to AS 1000, the internal AS.
3. Node F sends back a capability message with sequence
number 200, Add Action, and Dynamic AS Confed_Edge
capabiliity inside. Inside the Dynamic AS Confeded_Edge
capability, the flags are set to: EBGP, Start, AS-in-Use
Internal and Success. AGain, the AS information is: AS
Confederation 200 and AS internal 100.
Hares & Bose Expires April 19, 2006 [Page 19]
Internet-Draft DYNAS-Confed-Edge October 2005
11. At this point:
1. AS 300 has: Node A
2. AS 1000 has: Node C, B and E
3. AS 200 has Node D as an AS confederation with AS 2000
inside.
4. AS 2000 has only Node D.
5. AS 500 has Node F
6. AS 300 peers with AS 1000
7. AS 1000 peers with AS 200 (Node D), AS 300 (Node A), and
AS 500 (Node F).
The two stage commit allows the internal AS one stage to confirm
resources with IBGP peers prior to disturbing and E-BGP peers. If an
E-BGP peer fails after the IBGP cloud has switched, the single E-BGP
peer can be dropped and re-initialized.
If there is any local consideration that the AS has split and
existing routes may cause a black hole, implementation MAY set the
"re-announce all routes now" flag to prevent loops.
Hares & Bose Expires April 19, 2006 [Page 20]
Internet-Draft DYNAS-Confed-Edge October 2005
8. Security Considerations
The security of the BGP exchange is optionally secured by the TCP MD5
key.
Upon discussion with security reviewers, the addition of this feature
will neither improve nor detract from the TCP MD5 level of security.
The authors considered adding a "cookie" feature to further secure
this exchange. Again, review with security experts indicated this
"cookie" feature would not improve the security level.
The TCP session security will continue across the dynamic BGP peer
re-association. The TCP sessions dynamic MD5 re-association or key
switch would also allow TCP sessions to continue for a long period.
9. References
[1] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", March 1997, <ftp://ftp.isi.edu/in-notes/rfc2119>.
[2] ""Capability Adverstisement with BGP-4"", November 2002,
<http://www.ietf.org/rfc/rfc3392.txt>.
[3] ""Dynamic Capability for BGP-4"", March 2000, <http://
www.ietf.org/internet-drafts/draft-ietf-idr-dynamic-cap-06.txt>.
Hares & Bose Expires April 19, 2006 [Page 21]
Internet-Draft DYNAS-Confed-Edge October 2005
Authors' Addresses
Susan Hares
NextHop Technologies
825 Victors Way
Ann Arbor, MI 48105
Phone: +1-734-222-1610
Email: shares@nexthop.com
Pratik Bose
Lockheed
700 N Frederick Ave
Gaithersburg, MD 20879
Phone: +1-301-428-4215
Email: pratik.bose@lmco.com
Hares & Bose Expires April 19, 2006 [Page 22]
Internet-Draft DYNAS-Confed-Edge October 2005
Intellectual Property Statement
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Disclaimer of Validity
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Copyright Statement
Copyright (C) The Internet Society (2005). This document is subject
to the rights, licenses and restrictions contained in BCP 78, and
except as set forth therein, the authors retain all their rights.
Acknowledgment
Funding for the RFC Editor function is currently provided by the
Internet Society.
Hares & Bose Expires April 19, 2006 [Page 23]
| PAFTECH AB 2003-2026 | 2026-04-24 02:50:22 |