One document matched: draft-andreasen-mgcp-fax-08.txt
Differences from draft-andreasen-mgcp-fax-07.txt
Internet Engineering Task Force F. Andreasen
Internet Draft Cisco Systems
Document: draft-andreasen-mgcp-fax-08.txt
Category: Informational D. Hancock
CableLabs
Expires: Aug, 2008 Feb, 2008
Media Gateway Control Protocol Fax Package
draft-andreasen-mgcp-fax-08
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other documents
at any time. It is inappropriate to use Internet-Drafts as
reference material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Abstract
This document defines a Media Gateway Control Protocol (MGCP)
package to support fax calls. The package allows for fax calls to
be supported in two different ways. The first one utilizes ITU-T
Recommendation T.38 for fax relay under the control of the Call
Agent. The second one lets the gateway decide upon a method for fax
transmission as well as handle the details of the fax call without
Call Agent involvement.
Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in
this document are to be interpreted as described in BCP 14, RFC-2119
[RFC2119].
Andreasen Informational - Expires September 2005 1
MGCP Fax Package March 2008
Table of Contents
1. Introduction......................................................3
2. Fax Package Definition............................................3
2.1 LocalConnectionOptions..........................................3
2.1.1 T.38 Procedure (Strict or Loose)............................5
2.1.2 Gateway Procedure...........................................7
2.1.3 Off Procedure...............................................7
2.1.4 Mode Operation..............................................8
2.1.5 Detecting a Fax Call........................................9
2.1.6 Considerations for Which Procedures to Request.............10
2.2 Events and Signals.............................................11
2.2.1 Gateway Controlled Fax (gwfax).............................12
2.2.2 No Special Fax Handling (nopfax)...........................13
2.2.3 T.38 fax relay(t38):.......................................13
2.3 Connection Parameters..........................................14
2.4 Negotiation of T.38 Parameters.................................15
2.5 Implementation Considerations..................................16
2.5.1 Media IP Address and Port for T.38.........................16
2.5.2 Case Sensitivity...........................................17
2.5.3 Boolean Indicator after T.38 Parameters....................17
3. Call Flow Examples...............................................17
3.1 Call Agent Controlled T.38 Strict..............................17
3.2 Multiple and Different Options.................................24
3.3 Interaction with SIP Endpoints.................................31
4. Security Considerations..........................................37
5. IANA Considerations..............................................37
6. Summary of Changes...............................................37
7. Normative References.............................................38
8. Informative References...........................................38
9. Acknowledgements.................................................39
10. Author's Address................................................39
Full Copyright Statement............................................40
Disclaimer of validity..............................................40
Andreasen/Hancock Informational - Expires September 2008 2
MGCP Fax Package March 2008
1. Introduction
This document defines a Media Gateway Control Protocol (MGCP)
[RFC3435] package that enables MGCP controlled gateways to support
fax calls. The package enables fax calls to be supported in two
different ways. The first one utilizes ITU-T Recommendation T.38
using either UDPTL or TCP (see [T38]) for fax relay under the
control of the Call Agent. The second one lets the gateway decide
upon a method for fax transmission as well as handle the details of
the fax call without Call Agent involvement.
The fax package definition is provided in Section 2 and in Section 3
we provide three call flow examples showing how to use it. Security
considerations are found in Section 4, followed by the IANA
considerations and references.
2. Fax Package Definition
A package is defined for fax. The package defines new
LocalConnectionOptions, events, and connection parameters as
detailed below.
Package Name: FXR
Package Version: 0
2.1 LocalConnectionOptions
A new Fax LocalConnectionOptions (LCO) parameter is defined for fax
handling. The Call Agent supplies this fax LCO to indicate the
desired fax handling procedure to the Media Gateway. The fax LCO
contains a list of desired fax handling procedures ordered by
preference with the most desired procedure listed first. When the
parameter is explicitly included in a command, the gateway MUST be
able to use at least one of the listed procedures for the command to
succeed. The list can currently indicate one or more of the
following procedures (see Section 2.1.1 to 2.1.4 for further details
on these):
* T.38 Strict:
Use T.38 [T38] with either UDPTL or TCP for fax relay and have the
Call Agent control it. Assuming the procedure can be used (see
Section 2.1.1), a switch to T.38 procedures will be initiated upon
fax detection and a "t38(start)" event will be generated (see
Section 2.2). This mode requires an indication of T.38 support
from the remote side in order to be used, as described further in
Section 2.1.1.
* T.38 Loose:
Identical to T.38 Strict procedure, except that an indication of
T.38 support from the remote side is not required for the
procedure to be used.
Andreasen/Hancock Informational - Expires September 2008 3
MGCP Fax Package March 2008
* Off:
Do not invoke any special procedure for fax, except for echo
cancellation adjustment and possibly switching to another codec.
* Gateway:
Let the gateway control and decide how to handle fax calls without
Call Agent involvement. This includes the case where the gateway
does not do anything special for fax, hence by definition this
procedure can always be supported. If the gateway does invoke a
special procedure upon detection of fax, it will generate a
"gwfax(start)" event so the Call Agent can be notified about it
(see Section 2.2). The Call Agent SHOULD then refrain from
issuing potentially conflicting commands to the gateway until the
gateway ends its special fax handling procedure.
A gateway that ends up not being able to invoke any special
procedure for fax will generate a "nopfax(start)" event (see Section
2.2) upon detection of fax.
The set of possible values (i.e. procedures) for the fax LCO is
extensible. The prefix "x-", which indicates an optional extension,
and the prefix "x+", which indicates a mandatory extension, are
reserved for vendor-specific use.
In CreateConnection commands, the fax LCO value defaults to
"gateway". In ModifyConnection commands, the fax LCO value defaults
to its current value on the connection. Thus, if
LocalConnectionOptions are either omitted or the fax LCO is not
included in a ModifyConnection command, the previous fax LCO value
for the connection is retained, but without affecting the outcome of
the command; consequently, the gateway may now not apply any special
procedure to fax. If the Call Agent wants to ensure that a command
succeeds only when a fax procedure is applied, the command needs to
include the fax LCO explicitly.
As an example of this, assume that the CreateConnection command
successfully specified the use of "T.38 Strict", and a
ModifyConnection command is now received without the fax LCO,
but with a RemoteConnectionDescriptor indicating no support for
T.38; in that case, the ModifyConnection command will succeed,
however T.38 procedures will no longer be invoked upon fax
detection (a "nopfax" event will be generated). Had the Call
Agent instead included the fax LCO set to "T.38 Strict", the
command would have failed.
If multiple fax parameter values are provided, the gateway MUST
choose one of the procedures specified according to the order in
which they are supplied, except as follows:
1. If "gateway" would have been selected and it would have resulted
in no special procedure being applied, and
Andreasen/Hancock Informational - Expires September 2008 4
MGCP Fax Package March 2008
2. there are procedures other than "off" which are specified after
"gateway" (e.g., "t38")
then the gateway MUST use the most preferred of those subsequent
procedures that can be supported. If none of those subsequent
procedures can be supported, the gateway reverts to not invoking any
special procedure for fax. Please refer to Section 2.1.4 for
further details on determining which procedures can be supported.
The fax LCO parameter is encoded as the keyword "fx" (prefixed with
the package name per [RFC3435]), followed by a colon and a semicolon
separated list of values where T.38 Strict is encoded as "t38", T.38
Loose is encoded as "t38-loose", gateway is encoded as "gw", and off
is encoded as "off".
The following example illustrates the use of PCMU or G.729 for audio
encoding and T.38 Strict fax relay (preferred) or gateway control
for fax:
L: a:PCMU;G729, fxr/fx:t38;gw
It should be noted, that MGCP allows the CreateConnection command to
omit both LocalConnectionOptions and a RemoteConnectionDescriptor
thereby letting the gateway decide upon the media parameters to use.
When the T.38 fax package is supported, the gateway thus could
choose to do either audio or T.38 fax relay in such cases. Most
likely, the Call Agent requires one or the other to be used, and
hence it SHOULD NOT omit both LocalConnectionOptions and a
RemoteConnectionDescriptor in CreateConnection commands.
When auditing capabilities, the fax LCO may be returned with a semi-
colon separated list of supported fax handling parameters. The
values "t38", "t38-loose", "off" and "gw" MAY be omitted from such a
list as they are always implied. Gateways that implement additional
parameters SHOULD return these additional parameters when
capabilities are audited as illustrated by the following example:
A: a:image/t38, fxr/fx:mypar, ...
In the following subsections we provide additional detail on the
above defined fax procedures.
2.1.1 T.38 Procedure (Strict or Loose)
When a gateway is instructed to use one of the T.38 procedures
(strict or loose), also known as Call Agent controlled T.38 mode,
the "m=" line in the SDP returned will not indicate use of UDPTL-
based or TCP-based T.38 (unless the gateway was also instructed to
use "image/t38" for the media stream). Any other entity seeing this
SDP will not know whether T.38 is supported or not and hence whether
it is safe to attempt a switch to T.38 upon fax detection. To
remedy this dilemma, capability information for T.38 (if supported)
using the SDP Simple Capability Declaration extensions [RFC3407]
Andreasen/Hancock Informational - Expires September 2008 5
MGCP Fax Package March 2008
MUST be included. Other capability information is included as well,
regardless of whether the Call Agent authorized use of those in the
connection handling command or not. A subsequent attempt to
actually use these may of course not succeed, e.g., because the Call
Agent LCO does not allow them to be used. The following example
illustrates the RFC 3407 ([RFC3407]) capability descriptor - note
the inclusion of both current (audio) and latent (T.38) capabilities
as specified in RFC 3407 ([RFC3407]):
m=audio 3456 RTP/AVP 18
a=sqn: 0
a=cdsc: 1 audio RTP/AVP 18
a=cdsc: 2 image udptl t38
For a list of T.38 related parameters to be included in the SDP,
please refer to T.38 Annex D [T38].
Upon fax detection, a gateway which has successfully been instructed
to use one of the T.38 procedures will:
1. Initiate the T.38 fax relay procedure and mute the media channel
in both the send and receive direction (unless the media channel
is already using T.38).
2. Generate a "t38(start)" event.
3. Await further instructions from the Call Agent in order to
initiate the actual media change (unless the media channel is
already using T.38).
The Call Agent instructs the gateway to perform the media change by
sending it a ModifyConnection command with "image/t38" listed as the
encoding method in the LocalConnectionOptions (receipt of a
ModifyConnection command without LocalConnectionOptions but with a
RemoteConnectionDescriptor containing an "m=" line with the MIME
type "image/t38" would achieve the same). Per the normal MGCP codec
negotiation procedures (see [RFC3435] Section 2.6), if a
RemoteConnectionDescriptor was included as well, it needs to include
an "m=" line with "image/t38" as an acceptable media format in order
for the command to succeed. The gateway may choose between the
UDPTL and TCP transport protocols at its own discretion subject to
the normal MGCP codec negotiation procedures (in practice, TCP-based
implementations are currently rare).
If a RemoteConnectionDescriptor was not included with the
ModifyConnection command sent to a gateway that initiated the T.38
procedure, it is possible (in fact likely), that the last received
RemoteConnectionDescriptor did not include an "m=" line listing
"image/t38" as an acceptable media format. In that case, the
endpoint cannot send T.38 media to the other side. The endpoint
MUST instead wait for an updated RemoteConnectionDescriptor with
"image/t38" as an acceptable media format and a supported transport
protocol (UDPTL or TCP). The T.38 fax procedure continues when an
acceptable RemoteConnectionDescriptor is received. An acceptable
Andreasen/Hancock Informational - Expires September 2008 6
MGCP Fax Package March 2008
RemoteConnectionDescriptor contains an "m=" line with the
"image/t38" MIME type (using the normal SDP syntax) and a supported
transport protocol (UDPTL or TCP). If the fax call fails, e.g., due
to a fax timeout, while either waiting for the Call Agent to
instruct the gateway to switch to "image/t38" or waiting for an
acceptable RemoteConnectionDescriptor, a "t38(stop)" or a
"t38(failure)" event MUST be generated. When the T.38 procedure
ends, a "t38(stop)" or "t38(failure)" event MUST be generated.
Finally, the Call Agent may need to abort a T.38 procedure that is
in progress. This can for example be done when the remote side was
unable to switch to T.38, and a fallback to fax passthrough using an
audio codec is attempted. The Call Agent instructs the endpoint to
abort an in-progress T.38 procedure by use of the "off" Fax LCO as
illustrated below:
L: fxr/fx:off
We now define "time t38init" as the point in time where the T.38
procedure was initiated, and "time t38abort" as the point in time
where the Call Agent aborts an in-progress T.38 procedure. If the
Call Agent at time t38abort instructs or enables the endpoint to
revert to one or more codecs that were in use just prior to time
t38init, the endpoint SHOULD use media stream parameters that mimic
the most recent LocalConnectionDescriptor issued before time
t38init. For example, IP-address and UDP port, payload formats used
and their payload type mapping, should all be the same as before
time t38init. This will enable the fallback to be as rapid as
possible. A LocalConnectionDescriptor is returned as usual, i.e.,
only if one or more parameters changed since the last
LocalConnectionDescriptor issue (e.g. if a T.38 LCD was issued or a
transport address in the audio LCD was changed).
2.1.2 Gateway Procedure
A gateway using the gateway procedure, also known as Gateway
controlled mode, may initiate special fax handling upon detecting a
fax call. The details of this special fax handling are outside the
scope of this document. However, in order to use any special fax
handling, support for it MUST be negotiated with the other side by
passing and recognizing relevant parameters via the
LocalConnectionDescriptor and RemoteConnectionDescriptor. If the
other side has not indicated support for the special fax handling
desired, the gateway MUST NOT attempt to initiate it. When special
fax handling is initiated, a "gwfax(start)" event MUST be generated
thereby enabling the Call Agent to differ between the Call Agent and
gateway controlled mode while still being informed about the actual
change to fax. When the special gateway handling of fax ends, a
"gwfax(stop)" or "gwfax(failure)" event MUST be generated.
2.1.3 Off Procedure
Andreasen/Hancock Informational - Expires September 2008 7
MGCP Fax Package March 2008
A gateway using the "off" procedure will not invoke any special fax
procedures, e.g. T.38, when detecting a fax. However, the gateway
may still adjust local echo cancellation and/or switch to an
alternative codec as needed (in particular, this does not preclude
the use of RTP-based T.38). Also, a "nopfax(start)" event MUST be
generated; a corresponding "stop" event however will not.
Generating a "stop" event would imply that the gateway had to
infer when the fax call ends, which involves processing of the
media stream. However, when using the "off" mode, such processing
is not expected to occur.
2.1.4 Mode Operation
For each of the above modes, the RemoteConnectionDescriptor provides
information on what procedure(s) the other side supports. The
following rules are used to determine which procedure to use:
1. Whatever the Call Agent specified in the Fax
LocalConnectionOptions for the current command MUST be adhered
to. If the gateway cannot satisfy any of the options, the
command fails (error code 532 - unsupported value(s) in
LocalConnectionOptions is RECOMMENDED).
2. If both Fax LocalConnectionOptions and a
RemoteConnectionDescriptor are provided, the procedure selected
MUST be supported by both sides - this is currently only an issue
for "T.38 Strict". A procedure can be satisfied by the remote
side if:
* the relevant MIME media type, e.g. "image/t38", is included in
the "m=" line in the RemoteConnectionDescriptor, or
* the relevant MIME media type is included as a capability (see
[RFC3407]) in the RemoteConnectionDescriptor.
If the gateway cannot select any of the procedures in the Fax
LocalConnectionOptions, the command fails (error code 532 is
RECOMMENDED). Note that "T.38 Loose", "gateway", and "off" by
definition can always be supported by an implementation that
supports this package, irrespective of what the
RemoteConnectionDescriptor indicates.
3. If the Call Agent did not include any Fax LocalConnectionOptions
or a RemoteConnectionDescriptor with the command, the gateway
MUST continue using whichever procedure it is currently using.
4. If the Call Agent did not include any Fax LocalConnectionOptions,
but a RemoteConnectionDescriptor was included, the gateway MUST
follow rule 2 in selecting a procedure. In so doing, the default
Fax LocalConnectionOptions, i.e. "gateway" in CreateConnection,
or the current value in ModifyConnection, MUST be used. In the
case of ModifyConnection, the outcome of the command does not
Andreasen/Hancock Informational - Expires September 2008 8
MGCP Fax Package March 2008
depend on the gateway being able to select one of these "default"
procedures (as described in Section 2.1). Note that this is not
an issue for the CreateConnection command, since the default
value can always be supported by definition.
5. A previously received RemoteConnectionDescriptor does not affect
what procedure can be selected. Only a
RemoteConnectionDescriptor supplied with the current command
affects the procedure selection. However, in order to send media
of a given type (e.g. "image/t38"), the most recently received
RemoteConnectionDescriptor MUST include a corresponding media
line.
The following examples illustrate the use of the above rules:
Per rule 1, a gateway that only supports standard T.38 fax relay
will fail a command that only contains the fax option "mypar"
whereas it will succeed a command that contains, "t38-loose", "gw",
"off" or no Fax LCO. A command that only contained "t38", i.e. use
of T.38 in "strict" mode, may or may not succeed (depending on the
RemoteConnectionDescriptor).
A gateway supporting T.38 that receives a CreateConnection command
with the fax handling LCO set to "t38" and a
RemoteConnectionDescriptor with neither a T.38 capability nor a T.38
media stream will fail per rule 2. Had the fax handling LCO
included either "t38-loose", "gw" or "off", the command would have
succeeded and any of the procedures included could have been
selected.
Assume a gateway supporting T.38 has successfully executed a
CreateConnection command with fax handling set to "t38" (i.e.
strict). If the gateway now receives a ModifyConnection command
without a fax handling LCO but with a RemoteConnectionDescriptor
that has neither a T.38 capability nor a media stream with
"image/t38", the command will succeed (since rule 1 has no effect in
that case). However, per rule 2 and 4, there will not be any T.38
procedure in place. Had the Call Agent instead included a fax
handling LCO set to "t38" again, the command would have failed per
rule 2.
Finally, it should be noted that a switch to T.38 can be initiated
by either one or both of the originating and terminating gateways
and hence implementations MUST be prepared to handle this. This
includes the case where both sides initiate the switch, which for
example can occur when the originating fax generates Calling Tone
(CNG) and the terminating fax detects V.21 fax preamble (see [T30])
before the switch to T.38 has been performed on the terminating
side.
2.1.5 Detecting a Fax Call
Andreasen/Hancock Informational - Expires September 2008 9
MGCP Fax Package March 2008
A fax call can be detected by several different means, e.g. V.21 fax
preamble, T.30 CNG tone, or V.8 signals, depending on the fax
transmission method being used. Implementations of this package MUST
at a minimum detect a fax call based on V.21 fax preamble.
Triggering based on T.30 CNG tone MAY be done; this is generally
considered acceptable for G3 and lower fax speeds. However, when
used with T.38 version 2 or earlier, it will impact V.34 high-speed
fax. The reason is, that T.38 version 2 (and earlier) does not
support the V.8 ANSam and CM signals used with V.34 fax, and hence
the V.34 faxes will downspeed to G3 (14.400 bps) or lower when using
T.38 version 2 (or earlier). Also, a few rare cases of modems
generating T.30 CNG tones for non-fax calls have been reported; such
modems would generate a false trigger for fax. As a consequence of
the above, it is RECOMMENDED that implementations of this package
which support T.30 CNG based fax detection provide a configuration
option to disable it for T.38 version 2 (or earlier).
2.1.6 Considerations for Which Procedures to Request
It is important to understand the implications of using any one of
the above defined procedures. Furthermore, multiple alternative
procedures can be requested, however not all combinations make
sense. In this section, we elaborate on both of these issues.
Use of the T.38 strict mode is ideal in an environment where it is
known, that other endpoints generate RFC 3407 ([RFC3407]) capability
descriptions with T.38 fax relay information. If a
RemoteConnectionDescriptor without T.38 fax relay capabilities is
received in such an environment, it is known that the other side
does not support T.38, and hence an unsuccessful attempt to switch
to T.38 (which in turn may lead to a failed fax call) can be
avoided. If it is not known whether other endpoints support the RFC
3407 ([RFC3407]) capability descriptors or not, the tradeoff is less
clear. The advantage is, that a switch to T.38 will only be
attempted if it is known that the other side supports it, however
endpoints that do not indicate support for T.38 may still support
it; T.38 however will not be used with these which in turn may lead
to unnecessary fax failures with low-bandwidth codecs or lossy
networks.
Use of the T.38 loose mode involves the same considerations as for
T.38 strict, however the pros and cons are reversed. If a peer
endpoint does not support T.38, the T.38 loose mode will still
attempt to switch to T.38 (and fail), which in turn may lead to a
failed fax call. On the other hand, if the peer endpoint does not
support the RFC 3407 ([RFC3407]) capability descriptors, but the
peer endpoint does in fact support T.38, T.38 would still be used
with this mode.
In summary, there is no single good answer to the use of either T.38
strict or T.38 loose mode; it depends on the capabilities of the
endpoints involved as well as the trade-off between potentially
Andreasen/Hancock Informational - Expires September 2008 10
MGCP Fax Package March 2008
letting fax calls fail due to lack of capability indications (where
T.38 otherwise is supported) versus potentially letting fax calls
fail due to an unsuccessful switch to T.38 (because T.38 in fact was
not supported). It should be noted, that Call Agents may have means
beyond RFC 3407 ([RFC3407]) capability descriptors to determine if a
peer endpoint supports T.38 or not. For example, when SIP is used
as the signaling protocol with other peers (e.g. Call Agents or
other SIP devices), the SIP OPTIONS method can be used to learn
whether T.38 is supported. Also, if the Call Agent allows use of
high-bandwidth codecs with redundancy when support for T.38 is not
indicated, fax calls may still succeed without the use of T.38, even
in networks with non-negligible packet loss.
When the gateway controlled mode is selected, there will only be
special fax handling if the two peer endpoints support the same fax
handling method; note that the details of the actual method is
entirely up to the vendor. Also note, that if the two peer
endpoints either do not support the same method for fax handling, or
the method is not indicated in the SDP exchanged, there will be no
special fax handling in place. Furthermore, the Call Agent will not
be aware that this is the case until the fax transmission starts and
a "nopfax(start)" event is generated.
The off mode is straightforward; there will be no special procedure
in place for fax handling, except for the usual handling of echo
cancellation and possibly a change to a higher bandwidth codec.
Having looked at the individual procedures in more detail, we now
elaborate on some of the combinations of procedures that may be
requested:
* T.38 strict: If the T.38 strict procedure is placed after
the T.38 loose or the off procedure (both of which can always be
supported), it will not be selected. Apart from this, it makes
little sense to request both T.38 strict and T.38 loose.
* T.38 loose: The T.38 loose procedure can always be
supported, so any procedure specified after T.38 loose will not be
selected.
* Gateway: The gateway controlled procedure can always be
supported. If the gateway controlled procedure would have
resulted in no special fax procedure and further options (except
off) are provided, those procedures will be attempted. If neither
of those procedures can be supported, there will be no special fax
procedure in place.
* Off: The off procedure can always be supported. Any
procedure specified after this one will not be selected.
2.2 Events and Signals
The following events are defined in support of the above:
Andreasen/Hancock Informational - Expires September 2008 11
MGCP Fax Package March 2008
------------------------------------------------------------------
| Symbol | Definition | R | S Duration |
|---------|----------------------------|-----|---------------------|
| gwfax | Gateway controlled fax | x | |
| nopfax | No special fax handling | x | |
| t38 | T.38 fax relay | x | |
------------------------------------------------------------------
The definitions of the individual events are provided in the
following subsections.
2.2.1 Gateway Controlled Fax (gwfax)
The "gateway controlled fax" event occurs when the gateway handled
fax procedure either starts, stops or fails. The event is encoded as
"gwfax" and the following event parameters, which apply to
ObservedEvents only, are defined:
* start:
Gateway controlled fax procedure was initiated. The Call Agent
SHOULD refrain from issuing media handling instructions to the
gateway until either a "gwfax(stop)" or "gwfax(failure)" event
is generated.
* stop:
Gateway controlled fax procedure ended and the gateway did not
detect any errors. Note that this does not necessarily imply a
successfully transmitted fax. It merely indicates that the
gateway controlled fax procedure has ended and the procedure
itself did not encounter any errors. Media parameters for the
connection are as before the gateway handled fax procedure
started.
* failure:
The gateway controlled fax procedure ended abnormally. Some
kind of problem was encountered in the gateway controlled fax
procedure and the procedure ended. Media parameters are as
before the gateway handled fax procedure started.
One of the above parameters will be present when the event is
reported. The "gwfax" event MAY be parameterized with additional
parameters in ObservedEvents, however it is RECOMMENDED that one of
the above parameters is the first parameter supplied. Unknown
parameters MUST be ignored.
The following example illustrates the encoding of the "gwfax"
event:
O: fxr/gwfax(start)
O: fxr/gwfax(stop, foobar)
Andreasen/Hancock Informational - Expires September 2008 12
MGCP Fax Package March 2008
2.2.2 No Special Fax Handling (nopfax)
The "no special fax handling" event occurs when there is no special
fax handling procedure in place and a fax call is detected. This
can happen either due to no special fax handling procedure being
requested (including "off"), or negotiation leading to no special
fax handling procedure being possible. The event is encoded as
"nopfax" and the following event parameter, which applies to
ObservedEvents only, is defined:
* start:
No special fax handling procedure is in place, however a fax
call is now detected. The Call Agent may have to issue further
commands in order to ensure a successful fax call (e.g., switch
to another codec).
The above parameter will be present when the event is reported. The
"nopfax" event MAY be parameterized with additional parameters on
ObservedEvents, however it is RECOMMENDED that the above parameter
is the first parameter supplied. Unknown parameters MUST be
ignored. Note, that this event currently cannot be parameterized
with "stop" or "failure" as it only detects the beginning of a fax
call.
The following example illustrates the encoding of the "nopfax"
event:
O: fxr/nopfax(start)
2.2.3 T.38 Fax Relay (t38)
The "T.38 fax relay" event occurs when one of the T.38 fax relay
procedures (strict or loose) either starts, stops or fails. The
event is encoded as "t38" and the following event parameters, which
apply to ObservedEvents only, are defined:
* start:
A fax call was detected on the endpoint and the Call Agent
controlled T.38 fax relay procedure was initiated. The Call
Agent SHOULD modify each side of the connection to start using
the "image/t38" media format, unless they already do. Note that,
as long as use of the Call Agent controlled T.38 relay procedure
is in effect, the event will be generated upon fax call
detection irrespective of the current encoding method on any
connections on the endpoint (incl. "image/t38"). The T38(start)
event MUST be generated at most once by the endpoint per fax
call regardless of whether or not it is requested again in a
subsequent requested events list.
* stop:
Call Agent controlled T.38 fax relay procedure ended and the
gateway did not detect any errors. Note that this does not
necessarily imply a successfully transmitted fax. It merely
Andreasen/Hancock Informational - Expires September 2008 13
MGCP Fax Package March 2008
indicates that the Call Agent controlled T.38 fax relay
procedure has ended and the procedure itself did not encounter
any errors. The Call Agent may want to modify the media
parameters for each side of the connection. Note that, in
contrast to the gateway controlled fax procedure case, media
parameters such as codecs do not automatically revert to their
values before the start of the fax call; echo cancellation and
silence suppression however do per the procedures in [RFC3435]
Section 2.3.5. The "t38(stop)" event MUST NOT be generated
unless a corresponding "t38(start)" event for the fax call in
question was generated earlier.
* failure:
Call Agent controlled T.38 fax relay procedure ended
abnormally. Some kind of problem in the Call Agent controlled
T.38 fax relay procedure was encountered and the procedure
ended. The Call Agent may want to modify the media parameters
for each side of the connection. Note that, in contrast to the
gateway controlled fax procedure case, media parameters such as
codecs do not automatically revert to their state before the
start of the fax call; echo cancellation and silence suppression
however do per the procedures in [RFC3435] Section 2.3.5. The
"t38(failure)" event MUST NOT be generated unless a
corresponding "t38(start)" event for the fax call in question
was generated earlier.
One of the above parameters will be present when the event is
reported. The "t38" event MAY be parameterized with additional
parameters, however it is RECOMMENDED that one of the above
parameters is the first parameter supplied. Unknown parameters MUST
be ignored.
The following example illustrates the encoding of the "t38" event:
O: fxr/t38(start)
O: fxr/t38(stop, foobar)
2.3 Connection Parameters
The connection parameters for the connection, that measures packets
and octets sent and received, MUST include packets and octets for
fax handling as well. Interarrival jitter and average transmission
delay calculation however MAY not be performed while fax is in
progress, e.g., if T.38 is used. In such cases, the interarrival
jitter and average transmission delay calculations are simply
suspended until calculations can resume, e.g., by changing back to
an RTP-based media stream again.
In addition to these connection parameters, the fax package defines
the following connection parameters, which gateways MAY support:
Number of fax pages sent (PGS):
Andreasen/Hancock Informational - Expires September 2008 14
MGCP Fax Package March 2008
The cumulative number of fax pages sent by the endpoint for the
life of the connection. The parameter is encoded as "PGS" and the
value supplied is a string of up to nine decimal digits.
Number of fax pages received (PGR):
The cumulative number of fax pages received by the endpoint for
the life of the connection. The parameter is encoded as "PGR" and
the value supplied is a string of up to nine decimal digits.
The following example illustrates the use of these parameters:
P: FXR/PGS=3, FXR/PGR=0, PS=1245, OS=62345, ...
2.4 Negotiation of T.38 Parameters
T.38 Annex D defines a number of T.38 parameters that can be
negotiated in the SDP. Currently, T.38 does not specify procedures
for how each of these parameters is negotiated, and in particular
whether each side has to use the same value or not. In the absence
of that, it was considered to add such definitions and procedures
here. However, it is expected that T.38 will rectify the above,
which could lead to conflicting definitions and procedures. To avoid
that, we instead assume the existence of an offer/answer section for
T.38 where T.38 Annex D parameters are classified as either
declarative or negotiated, and we then provide guidelines for how to
map such definitions and procedures to the MGCP fax package defined
here.
MGCP does not specify use of the offer/answer model, but instead
operates with the concept of connection handling commands (e.g.
CreateConnection and ModifyConnection) that may include a
RemoteConnectionDescriptor (SDP) and in turn may generate a
LocalConnectionDescriptor (SDP) in their response.
When an MGCP endpoint receives a CreateConnection command without a
RemoteConnectionDescriptor, it should follow the corresponding T.38
procedures for generating an initial offer and return the resulting
SDP in its LocalConnectionDescriptor.
When an MGCP endpoint receives a CreateConnection command with a
RemoteConnectionDescriptor, it should follow the corresponding T.38
procedures for receiving an initial offer and generating an answer
to it. The resulting SDP is returned in the
LocalConnectionDescriptor.
When an MGCP endpoint receives a ModifyConnection command with a
RemoteConnectionDescriptor, it cannot determine whether this
corresponds to an answer to an initial offer or a new offer. This is
not an issue for declarative parameters since they can be specified
independently in either direction. Negotiated parameters however
require some consideration:
Andreasen/Hancock Informational - Expires September 2008 15
MGCP Fax Package March 2008
When an offerer receives an answer to a previous offer, the
negotiation has completed and the parameters negotiated can no
longer be changed with this offer/answer exchange. The negotiated
parameters may be subject to certain validation checks. Conversely,
when an answerer receives an offer, the negotiation is open and the
answerer may change some of the offered negotiated parameters. Since
the MGCP endpoint does not know which situation it is in, it can not
perform the "offerer" validation checks. Likewise, in order to
ensure that any required negotiation actually takes place, it needs
to process an incoming SDP as an offer. If the SDP in fact does
correspond to an offer then this is obviously correct behavior. If
the SDP however corresponds to an answer, and one or more negotiated
parameters did change, then this will result in a new SDP. The Call
Agent may or may not contain sufficient intelligence to determine
whether this new SDP needs to result in another offer/answer
exchange or not.
For example, if the initial offer (in response to a
CreateConnection without SDP) contained fax version 2, and the
answer (in response to a CreateConnection with SDP) contained fax
version 0, then the corresponding ModifyConnection command (with
SDP) will result in an updated SDP with fax version also set to
zero. If this was the only change in the updated SDP, a new
offer/answer exchange would not be needed. Note that this example
does not imply that it is generally considered a good idea for
Call Agents to parse SDP in order to determine whether new
offer/answer exchanges are needed or not.
Finally, a ModifyConnection without SDP that generates an SDP needs
to be considered. The SDP generated may either correspond to an
initial offer/answer exchange or a subsequent offer/answer exchange.
The endpoint should generate SDP as if it was part of a subsequent
offer/answer exchange. If the Call Agent does not desire such
semantics, it can simply create a new connection instead.
2.5 Implementation Considerations
2.5.1 Media IP Address and Port for T.38
When an endpoint is instructed to change to or from T.38 for a media
stream, it SHOULD continue using the same IP address and port as the
media stream is currently using, since this will minimize any
Quality of Service, Network Address Translator (NAT) and Firewall
interactions from the change. However, if an endpoint has a good
reason, it MAY choose not to follow this recommendation.
When an endpoint uses the same port for RTP audio and T.38 with
either UDPTL or TCP, packets of one type (e.g. T.38) may be received
while expecting packets of another type (RTP audio). Since there is
explicit signaling to indicate which type is expected at any given
point in time, this does not introduce any new problems. In other
words, the receiver does not operate as a demultiplexer with a need
to determine if a given packet received is an RTP audio packet or a
Andreasen/Hancock Informational - Expires September 2008 16
MGCP Fax Package March 2008
T.38 UDPTL/TCP packet. The receiver simply processes incoming
packets as usual. If T.38 packets are expected, then incoming
packets are validated against T.38, and if RTP audio packets are
expected, then incoming packets are validated against RTP.
2.5.2 Case Sensitivity
The IANA has registered the uppercase string "UDPTL" as the
transport protocol identifier to be used for UDP-based T.38.
However, the examples provided in Recommendation T.38 as well as
most (if not all) current implementations use the lowercase string
"udptl" instead. Implementations conforming to this package SHOULD
generate the lowercase string "udptl" and accept the lowercase,
uppercase, and mixed upper/lowercase strings as being equivalent.
The attribute "T38MaxBitRate" is incorrectly registered with IANA as
"T38maxBitRate" (lower-case "m"). In accordance with T.38 examples
and common implementation practice, the form "T38MaxBitRate" SHOULD
be generated by implementations conforming to this package.
In general, it is RECOMMENDED that implementations of this package
accept both lowercase, uppercase, and mixed upper/lowercase
encodings of all the T.38 attributes.
2.5.3 Boolean Indicator after T.38 Parameters
Some implementations incorrectly use a colon (':') followed by a
number (zero or one) after the attributes T38FaxFillBitRemoval,
T38FaxTranscodingMMR and T38FaxTranscodingJBIG. Implementations
that receive such erroneous encodings MAY interpret the value ":0"
as lack of support for the option and all other values as indicating
support of the option in question.
3. Call Flow Examples
In this section, we provide three example call flows. The first one
illustrates a T.38 fax call under Call Agent control on both the
originating and terminating side. The second one illustrates the
use of multiple and different options on the two sides. The third
one illustrates the interaction with a SIP endpoint.
3.1 Call Agent Controlled T.38 Strict
In this example, both sides are under strict T.38 Call Agent
control. We assume the originating and terminating Call Agents
communicate via the Session Initiation Protocol (SIP) [RFC3261].
Furthermore, the originating fax machine does not generate CNG tone
which is typical of early (i.e. pre-1993) fax machines.
Andreasen/Hancock Informational - Expires September 2008 17
MGCP Fax Package March 2008
------------------------------------------------------------------
| #| GW-o | CA-o | CA-t | GW-t |
|==|===============|===============|===============|===============|
| 1| <-|CRCX | | |
| 2| 200(sdp-o)|-> | | |
| 3| | INVITE(sdp-o)|-> | |
| 4| | | CRCX(sdp-o)|-> |
| 5| | | <-|200 (sdp-t) |
| 6| | <-|200(sdp-t) | |
| 7| <-|MDCX(sdp-t) | | |
| 8| 200|-> | | |
|--|---------------|---------------|---------------|---------------|
| 9| | | | <- ANS/ |
| | | | | T.30 CED |
|10| | | | <- V.21 fax |
| | | | | preamble |
|11| | | <-|NTFY(t38 start)|
|12| | | 200|-> |
|13| | | MDCX(t38)|-> |
|14| | | <-|200(sdp-t2) |
|15| | <-|INVITE(sdp-t2) | |
|16| <-|MDCX(sdp-t2) | | |
|17| 200(sdp-o2)|-> | | |
|18| | 200(sdp-o2)|-> | |
|19| | | MDCX(sdp-o2)|-> |
|20| | | <-|200 |
|21| V.21 fax -> | | | |
| | preamble | | | |
|22|NTFY(t38 start)|-> | | |
|23| <-|200 | | |
|24| <-|RQNT(T38 event)| | |
|25| 200|-> | | |
|--|---------------|---------------|---------------|---------------|
|26| | | | (fax ends) |
|27| | | <-|NTFY(t38 stop) |
|28| | | 200|-> |
|29|NTFY(t38 stop) |-> | | |
|30| <-|200 | | |
------------------------------------------------------------------
Step 1:
The Call Agent issues a CreateConnection command to the gateway
instructing it to use PCMU media encoding and to use the strict Call
Agent controlled T.38 procedure. Consequently, the Call Agent asks
the gateway to notify it of the t38 event:
CRCX 1000 ds/ds1-1/1@gw-o.whatever.net MGCP 1.0
C: 1
L: a:PCMU, fxr/fx:t38
M: recvonly
R: fxr/t38
X: 1
Andreasen/Hancock Informational - Expires September 2008 18
MGCP Fax Package March 2008
Step 2:
The gateway acknowledges the command and includes SDP with codec
information as well as RFC 3407 ([RFC3407]) capability information:
200 1000 OK
I:1
v=0
o=- 25678 753849 IN IP4 192.0.2.1
s=-
c=IN IP4 192.0.2.1
t=0 0
m=audio 3456 RTP/AVP 0
a=sqn: 0
a=cdsc: 1 audio RTP/AVP 0 18
a=cdsc: 3 image udptl t38
Step 3:
The originating Call Agent sends a SIP INVITE message with the SDP
to the terminating Call Agent.
Step 4:
The terminating Call Agent issues a CreateConnection command to the
terminating gateway instructing it to use PCMU media encoding and to
use the strict Call Agent controlled T.38 procedure. Consequently,
the Call Agent asks the gateway to notify it of the t38 event:
CRCX 2000 ds/ds1-1/2@gw-t.whatever.net MGCP 1.0
C: 2
L: a:PCMU, fxr/fx:t38
M: sendrecv
R: fxr/t38
X: 20
v=0
o=- 25678 753849 IN IP4 192.0.2.1
s=-
c=IN IP4 192.0.2.1
t=0 0
m=audio 3456 RTP/AVP 0
a=sqn: 0
a=cdsc: 1 audio RTP/AVP 0 18
a=cdsc: 3 image udptl t38
Step 5:
The terminating gateway supports T.38, and the
RemoteConnectionDescriptor included indicates that the other side
supports T.38 as well, so the strict T.38 Call Agent controlled
procedure requested can be used. The terminating gateway sends back
Andreasen/Hancock Informational - Expires September 2008 19
MGCP Fax Package March 2008
a success response with its SDP which also includes capability
information:
200 2000 OK
I:2
v=0
o=- 25678 753849 IN IP4 192.0.2.2
s=-
c=IN IP4 192.0.2.2
t=0 0
m=audio 1296 RTP/AVP 0
a=sqn: 0
a=cdsc: 1 audio RTP/AVP 0 18
a=cdsc: 3 image udptl t38
Step 6:
The terminating Call Agent sends back a SIP 200 OK response to the
originating Call Agent, which in turn sends a SIP ACK (not shown).
Step 7:
The originating Call Agent in turns sends a ModifyConnection command
to the originating gateway:
MDCX 1001 ds/ds1-1/1@gw-o.whatever.net MGCP 1.0
C: 1
I: 1
M: sendrecv
v=0
o=- 25678 753849 IN IP4 192.0.2.2
s=-
c=IN IP4 192.0.2.2
t=0 0
m=audio 1296 RTP/AVP 0
a=sqn: 0
a=cdsc: 1 audio RTP/AVP 0 18
a=cdsc: 3 image udptl t38
The ModifyConnection command does not repeat the
LocalConnectionOptions sent previously. As far as fax handling is
concerned, the gateway therefore attempts to continue using the
current fax handling procedure, i.e. strict Call Agent controlled
T.38. Since the capability information indicates the other side
supports T.38, the gateway will in fact be able to use the strict
Call Agent controlled T.38 procedure. Had there not been any
support for T.38 in the RemoteConnectionDescriptor, then this
command would still have succeeded, however there would be no
special fax handling procedure (since strict mode could not be
supported).
Step 8:
Andreasen/Hancock Informational - Expires September 2008 20
MGCP Fax Package March 2008
The gateway acknowledges the command. At this point, a call is
established using PCMU encoding, and if a fax call is detected, the
Call Agent controlled T.38 procedure will be initiated.
Step 9-11:
A fax call now occurs. First, the T.30 CED tone (a.k.a. V.25 ANS)
is sent which in this case is simply passed through the current PCMU
encoding. Since both fax and modem calls can start with this
sequence, it is not possible to determine that this is a fax call
until step 10, where the V.21 fax preamble is detected.
The gateway was instructed to apply the Call Agent controlled T.38
procedure for fax calls, so it begins to mute audio, generates the
"t38(start)" event, and notifies the Call Agent:
NTFY 2500 ds/ds1-1/2@gw-t.whatever.net MGCP 1.0
O: fxr/t38(start)
X: 20
Step 12:
The Call Agent acknowledges the Notify command:
200 2500 OK
Step 13:
The Call Agent then instructs the terminating gateway to change to
using the "image/t38" MIME type instead:
MDCX 2002 ds/ds1-1/2@gw-t.whatever.net MGCP 1.0
C: 2
I: 2
L: a:image/t38
R: fxr/t38
X: 21
Step 14:
The gateway changes to T.38, and sends back a success response with
updated SDP:
200 2002 OK
v=0
o=- 25678 753850 IN IP4 192.0.2.2
s=-
c=IN IP4 192.0.2.2
t=0 0
m=image 1296 udptl t38
a=sqn: 0
a=cdsc: 1 audio RTP/AVP 0 18
Andreasen/Hancock Informational - Expires September 2008 21
MGCP Fax Package March 2008
a=cdsc: 3 image udptl t38
Note, that since the gateway's current RemoteConnectionDescriptor
(as opposed to the LocalConnectionDescriptor returned here) does not
list "image/t38" as a valid encoding method, the terminating gateway
is still muting the media and is now waiting for an updated
RemoteConnectionDescriptor with "image/t38".
Step 15:
The terminating Call Agent sends a re-INVITE to the originating Call
Agent with the updated SDP.
Step 16:
The originating Call Agent then sends a ModifyConnection command to
the originating gateway:
MDCX 1003 ds/ds1-1/1@gw-o.whatever.net MGCP 1.0
C: 1
I: 1
v=0
o=- 25678 753850 IN IP4 192.0.2.2
s=-
c=IN IP4 192.0.2.2
t=0 0
m=image 1296 udptl t38
a=sqn: 0
a=cdsc: 1 audio RTP/AVP 0 18
a=cdsc: 3 image udptl t38
Step 17:
The originating gateway changes to T.38 and sends back a success
response with updated SDP:
200 1003 OK
v=0
o=- 25678 753850 IN IP4 192.0.2.1
s=-
c=IN IP4 192.0.2.1
t=0 0
m=image 3456 udptl t38
a=sqn: 0
a=cdsc: 1 audio RTP/AVP 0 18
a=cdsc: 3 image udptl t38
Step 18:
Andreasen/Hancock Informational - Expires September 2008 22
MGCP Fax Package March 2008
The originating Call Agent sends a SIP 200 OK response with the
updated SDP to the terminating Call Agent, which in turn sends a SIP
ACK (not shown).
Step 19:
The terminating Call Agent sends a ModifyConnection with the updated
SDP to the terminating gateway:
MDCX 2003 ds/ds1-1/2@gw-t.whatever.net MGCP 1.0
C: 2
I: 2
v=0
o=- 25678 753850 IN IP4 192.0.2.1
s=-
c=IN IP4 192.0.2.1
t=0 0
m=image 3456 udptl t38
a=sqn: 0
a=cdsc: 1 audio RTP/AVP 0 18
a=cdsc: 3 image udptl t38
Step 20:
The terminating gateway sends back a success response:
200 2003 OK
Since the terminating gateway now has a RemoteConnectionDescriptor
with "image/t38" as valid media, it can start exchanging T.38 with
the originating gateway.
Step 21, 22:
The originating endpoint detects V.21 fax preamble. Even though the
endpoint is already using "image/t38" for media, it generates a
"t38(start)" event and notifies the Call Agent.
NTFY 3500 ds/ds1-1/1@gw-o.whatever.net MGCP 1.0
O: fxr/t38(start)
X: 1
Step 23, 24:
The Call Agent acknowledges the Notify command, then issues a new
request for notification of the T38 event.
200 3500 OK
.
RQNT 1004 ds/ds1-1/1@gw-o.whatever.net MGCP 1.0
R: fxr/t38
X: 2
Andreasen/Hancock Informational - Expires September 2008 23
MGCP Fax Package March 2008
Step 25:
The gateway acknowledges the command.
200 1004 OK
Step 26, 27:
When the fax ends, a "t38(stop)" event is generated by the
terminating endpoint, which is notified to the Call Agent:
NTFY 2501 ds/ds1-1/2@gw-t.whatever.net MGCP 1.0
O: t38(stop)
X: 21
Step 28:
The Call Agent acknowledges the Notify command:
200 2501 OK
Step 29:
The originating endpoint also generates a "t38(stop)" event, which
is notified to the Call Agent:
NTFY 3502 ds/ds1-1/1@gw-o.whatever.net MGCP 1.0
O: t38(stop)
X: 2
Step 30:
The Call Agent acknowledges the Notify command:
200 3502 OK
The fax call is now over. The Call Agent may now decide to change
back to a voice codec, delete the connection, or something
different.
3.2 Multiple and Different Options
In this example, the originating gateway is instructed to use the
gateway procedure whereas the terminating gateway is given a choice
between the gateway procedure and the strict t38 procedure.
Furthermore, the originating fax machine is generating CNG tone.
------------------------------------------------------------------
| #| GW-o | CA-o | CA-t | GW-t |
|==|===============|===============|===============|===============|
| 1| <-|CRCX | | |
| 2| 200(sdp-o)|-> | | |
| 3| | INVITE(sdp-o)|-> | |
Andreasen/Hancock Informational - Expires September 2008 24
MGCP Fax Package March 2008
| 4| | | CRCX(sdp-o)|-> |
| 5| | | <-|200 (sdp-t) |
| 6| | <-|200(sdp-t) | |
| 7| <-|MDCX(sdp-t) | | |
| 8| 200|-> | | |
|--|---------------|---------------|---------------|---------------|
| 9| CNG ->| | | |
|10| | | |<- ANS/T.30 CED|
|11| | | |<- V.21 fax |
| | | | | preamble |
|12| | | <-|NTFY(t38 start)|
|13| | | 200|-> |
|14| | | MDCX(t38)|-> |
|15| | | <-|200(sdp-t2) |
|16| | <-|INVITE(sdp-t2) | |
|17| <-|MDCX(sdp-t2) | | |
|18| 200(sdp-o2)|-> | | |
|19| | 200(sdp-o2)|-> | |
|20| | | MDCX(sdp-o2)|-> |
|21| | | <-|200 |
|--|---------------|---------------|---------------|---------------|
|22| | | | (fax ends) |
|23| | | <-|NTFY(t38 stop) |
|24| | | 200|-> |
------------------------------------------------------------------
Step 1:
The Call Agent issues a CreateConnection command to the gateway
instructing it to use PCMU media encoding and to use the gateway
procedure. Consequently, the Call Agent asks the gateway to notify
it of the gwfax event:
CRCX 1000 ds/ds1-1/1@gw-o.whatever.net MGCP 1.0
C: 1
L: a:PCMU, fxr/fx:gw
M: recvonly
R: fxr/gwfax
X: 1
Step 2:
The gateway acknowledges the command and includes SDP with codec
information as well as capability information:
Andreasen/Hancock Informational - Expires September 2008 25
MGCP Fax Package March 2008
200 1000 OK
I:1
v=0
o=- 25678 753849 IN IP4 192.0.2.1
s=-
c=IN IP4 192.0.2.1
t=0 0
m=audio 3456 RTP/AVP 0
a=sqn: 0
a=cdsc: 1 audio RTP/AVP 0 18
a=cdsc: 3 image udptl t38
a=X-FaxScheme: 123
We assume the gateway supports some other fax scheme and it
indicates this by including an attribute "X-FaxScheme: 123"
Step 3:
The originating Call Agent sends a SIP INVITE message with the SDP
to the terminating Call Agent.
Step 4:
The terminating Call Agent issues a CreateConnection command to the
terminating gateway instructing it to use PCMU media encoding and to
use either the gateway procedure or the strict Call Agent controlled
T.38 procedure. Consequently, the Call Agent asks the gateway to
notify it of both the gwfax and t38 events:
CRCX 2000 ds/ds1-1/2@gw-t.whatever.net MGCP 1.0
C: 2
L: a:PCMU, fxr/fx:gw;t38
M: sendrecv
R: fxr/t38, fxr/gwfax
X: 20
v=0
o=- 25678 753849 IN IP4 192.0.2.1
s=-
c=IN IP4 192.0.2.1
t=0 0
m=audio 3456 RTP/AVP 0
a=sqn: 0
a=cdsc: 1 audio RTP/AVP 0 18
a=cdsc: 3 image udptl t38
a=X-FaxScheme: 123
Step 5:
The terminating gateway does not support any special gateway fax
handling, however it does support T.38, and the
RemoteConnectionDescriptor included indicates that the other side
Andreasen/Hancock Informational - Expires September 2008 26
MGCP Fax Package March 2008
supports T.38 as well, so the strict T.38 Call Agent controlled
procedure requested can be honored. The terminating gateway sends
back a success response with its SDP which also includes capability
information:
200 2000 OK
I:2
v=0
o=- 25678 753849 IN IP4 192.0.2.2
s=-
c=IN IP4 192.0.2.2
t=0 0
m=audio 1296 RTP/AVP 0
a=sqn: 0
a=cdsc: 1 audio RTP/AVP 0 18
a=cdsc: 3 image udptl t38
Step 6:
The terminating Call Agent sends back a SIP 200 OK response to the
originating Call Agent, which in turn sends a SIP ACK (not shown).
Step 7:
The originating Call Agent in turns sends a ModifyConnection command
to the originating gateway:
MDCX 1001 ds/ds1-1/1@gw-o.whatever.net MGCP 1.0
C: 1
I: 1
M: sendrecv
v=0
o=- 25678 753849 IN IP4 192.0.2.2
s=-
c=IN IP4 192.0.2.2
t=0 0
m=audio 1296 RTP/AVP 0
a=sqn: 0
a=cdsc: 1 audio RTP/AVP 0 18
a=cdsc: 3 image udptl t38
The ModifyConnection command does not repeat the
LocalConnectionOptions sent previously. As far as fax handling is
concerned, the gateway therefore attempts to continue using the
current fax handling, i.e. the gateway procedure. The SDP
information returned however does not indicate support for the "X-
FaxScheme: 123", and hence the originating gateway will not invoke
any special fax handling procedure for this call.
Andreasen/Hancock Informational - Expires September 2008 27
MGCP Fax Package March 2008
Step 8:
The gateway acknowledges the command. At this point, a call is
established using PCMU encoding and if a fax call is detected, no
special fax handling procedure will occur.
Step 9-12:
First, a CNG tone is generated by the originating fax thereby
indicating a fax call. If the gateway was using either of the T.38
modes, or it had negotiated support for a special gateway handling
procedure with the other side, a "t38(start)" or "gwfax(start)"
event would now have been generated and the switch to T.38 (or
special gateway handling) could start. However, since the
negotiation with the terminating gateway resulted in the originating
gateway not doing anything special for fax, no such event is
generated. Instead, the "nopfax(start)" event is now generated, but
since the Call Agent has not requested this event, it is not
detected and hence not reported to the Call Agent. Consequently,
the CNG tone is simply passed through the current PCMU encoding
without the (originating) Call Agent being aware of the fax call.
Subsequently, the T.30 CED tone (a.k.a. V.25 ANS) occurs which in
this case is also simply passed through the current PCMU encoding.
Since both fax and modem calls can start with this sequence, it is
not possible to determine that this is a fax call until step 11,
where the V.21 fax preamble is detected.
The terminating gateway is using the Call Agent controlled T.38
procedure for fax calls, so it begins to mute audio, generates the
"t38(start)" event, and notifies the Call Agent:
NTFY 2500 ds/ds1-1/2@gw-t.whatever.net MGCP 1.0
O: fxr/t38(start)
X: 20
Step 13:
The Call Agent acknowledges the Notify command:
200 2500 OK
Step 14:
The Call Agent then instructs the terminating gateway to change to
using the "image/t38" MIME type instead:
MDCX 2002 ds/ds1-1/2@gw-t.whatever.net MGCP 1.0
C: 2
I: 2
L: a:image/t38
R: fxr/t38
X: 21
Andreasen/Hancock Informational - Expires September 2008 28
MGCP Fax Package March 2008
Step 15:
The gateway changes to T.38, and sends back a success response with
updated SDP:
200 2002 OK
v=0
o=- 25678 753850 IN IP4 192.0.2.2
s=-
c=IN IP4 192.0.2.2
t=0 0
m=image 1296 udptl t38
a=sqn: 0
a=cdsc: 1 audio RTP/AVP 0 18
a=cdsc: 3 image udptl t38
Note, that since the terminating gateway's last received
RemoteConnectionDescriptor (as opposed to the
LocalConnectionDescriptor returned here) did not list "image/t38" as
a valid encoding method, the terminating gateway is still muting the
media and is now waiting for an updated RemoteConnectionDescriptor
with "image/t38".
Step 16:
The terminating Call Agent sends a re-INVITE to the originating Call
Agent with the updated SDP.
Step 17:
The originating Call Agent then sends a ModifyConnection command to
the originating gateway:
MDCX 1003 ds/ds1-1/1@gw-o.whatever.net MGCP 1.0
C: 1
I: 1
v=0
o=- 25678 753850 IN IP4 192.0.2.2
s=-
c=IN IP4 192.0.2.2
t=0 0
m=image 1296 udptl t38
a=sqn: 0
a=cdsc: 1 audio RTP/AVP 0 18
a=cdsc: 3 image udptl t38
Step 18:
The originating gateway changes to T.38 and sends back a success
response with updated SDP:
Andreasen/Hancock Informational - Expires September 2008 29
MGCP Fax Package March 2008
200 1003 OK
v=0
o=- 25678 753850 IN IP4 192.0.2.1
s=-
c=IN IP4 192.0.2.1
t=0 0
m=image 3456 udptl t38
a=sqn: 0
a=cdsc: 1 audio RTP/AVP 0 18
a=cdsc: 3 image udptl t38
Step 19:
The originating Call Agent sends a SIP 200 OK response with the
updated SDP to the terminating Call Agent, which in turn sends a SIP
ACK (not shown).
Step 20:
The terminating Call Agent sends a ModifyConnection with the updated
SDP to the terminating gateway:
MDCX 2003 ds/ds1-1/2@gw-t.whatever.net MGCP 1.0
C: 2
I: 2
v=0
o=- 25678 753850 IN IP4 192.0.2.1
s=-
c=IN IP4 192.0.2.1
t=0 0
m=image 3456 udptl t38
a=sqn: 0
a=cdsc: 1 audio RTP/AVP 0 18
a=cdsc: 3 image udptl t38
Step 21:
The terminating gateway sends back a success response:
200 2003 OK
Since the terminating gateway now has a RemoteConnectionDescriptor
with "image/t38" as valid media, it can start exchanging T.38 with
the originating gateway.
Step 22, 23:
When the fax ends, a "t38(stop)" event is generated, which is
notified to the Call Agent:
NTFY 2501 ds/ds1-1/2@gw-t.whatever.net MGCP 1.0
O: t38(stop)
Andreasen/Hancock Informational - Expires September 2008 30
MGCP Fax Package March 2008
X: 21
Step 24:
The Call Agent acknowledges the Notify command:
200 2501 OK
The fax call is now over. The Call Agent may now decide to change
back to a voice codec, delete the connection, or something
different.
3.3 Interaction with SIP Endpoints
In this example, we show interaction with a SIP endpoint that does
not support the RFC 3407 ([RFC3407]) capability descriptors. To
accommodate such endpoints, the T.38 loose mode is being used (at
the risk of initiating T.38 to an endpoint that does not support
it). Once again, the originating fax does not generate CNG tone.
Andreasen/Hancock Informational - Expires September 2008 31
MGCP Fax Package March 2008
------------------------------------------------------------------
| #| GW-o | CA-o | SIP-UA-t | fax |
|==|===============|===============|===============|===============|
| 1| <-|CRCX | | |
| 2| 200(sdp-o)|-> | | |
| 3| | INVITE(sdp-o)|-> | |
| 4| | <-|200(sdp-t) | |
| 5| | ACK|-> | |
| 6| <-|MDCX(sdp-t) | | |
| 7| 200|-> | | |
|--|---------------|---------------|---------------|---------------|
| 8| | | | <- ANS/ |
| | | | | T.30 CED |
| 9| | | | <- V.21 fax |
| | | | | preamble |
|10| | <-|INVITE(sdp-t2) | |
|11| <-|MDCX(sdp-t2) | | |
|12| 200(sdp-o2)|-> | | |
|13| | 200(sdp-o2)|-> | |
|14| | <-|ACK | |
|15| V.21 fax -> | | | |
| | preamble | | | |
|16|NTFY(t38 start)|-> | | |
|17| <-|200 | | |
|18| <-|RQNT(T38 event)| | |
|19| 200|-> | | |
|--|---------------|---------------|---------------|---------------|
|20| | | | (fax ends) |
|21| | <-|BYE | |
|22| | 200|-> | |
|23|NTFY(t38 stop) |-> | | |
|24| <-|200 | | |
------------------------------------------------------------------
Step 1:
The Call Agent issues a CreateConnection command to the gateway
instructing it to use PCMU media encoding and to use the loose Call
Agent controlled T.38 procedure. Consequently, the Call Agent asks
the gateway to notify it of the t38 event:
CRCX 1000 ds/ds1-1/1@gw-o.whatever.net MGCP 1.0
C: 1
L: a:PCMU, fxr/fx:t38-loose
M: recvonly
R: fxr/t38
X: 1
Step 2:
The gateway acknowledges the command and includes SDP with codec
information as well as RFC 3407 ([RFC3407]) capability information:
Andreasen/Hancock Informational - Expires September 2008 32
MGCP Fax Package March 2008
200 1000 OK
I:1
v=0
o=- 25678 753849 IN IP4 192.0.2.1
s=-
c=IN IP4 192.0.2.1
t=0 0
m=audio 3456 RTP/AVP 0
a=sqn: 0
a=cdsc: 1 audio RTP/AVP 0 18
a=cdsc: 3 image udptl t38
Step 3:
The originating SIP User Agent sends a SIP INVITE message with the
SDP to the terminating Call Agent (not all SIP details shown here):
INVITE sip:bob@biloxi.example.com SIP/2.0
...
Content-Type: application/sdp
Content-Length: 167
v=0
o=- 25678 753849 IN IP4 192.0.2.1
s=-
c=IN IP4 192.0.2.1
t=0 0
m=audio 3456 RTP/AVP 0
a=sqn: 0
a=cdsc: 1 audio RTP/AVP 0 18
a=cdsc: 3 image udptl t38
Step 4:
The terminating SIP User Agent sends back a SIP 200 OK response (not
all SIP details shown) to the originating Call Agent:
SIP/2.0 200 OK
...
Content-Type: application/sdp
Content-Length: 100
v=0
o=- 25678 753849 IN IP4 192.0.2.2
s=-
c=IN IP4 192.0.2.2
t=0 0
m=audio 1296 RTP/AVP 0
Note that the terminating SIP User Agent does not use the RFC 3407
([RFC3407]) capability descriptor to indicate support for (or lack
of support for) T.38.
Andreasen/Hancock Informational - Expires September 2008 33
MGCP Fax Package March 2008
Step 5:
The originating Call Agent receives the SIP 200 response and sends a
SIP ACK message to the terminating SIP UA.
Note that the Call Agent does not know whether the peer entity
supports T.38 or not. In order to figure this out, the Call Agent
could send a SIP OPTIONS request to the terminating SIP UA
requesting it to return its capabilities (not shown). Note that
this can of course be done towards any SIP peer, e.g. if the other
side was a Call Agent speaking SIP it could be done there too.
Step 6:
The originating Call Agent in turns sends a ModifyConnection command
to the originating gateway:
MDCX 1001 ds/ds1-1/1@gw-o.whatever.net MGCP 1.0
C: 1
I: 1
M: sendrecv
v=0
o=- 25678 753849 IN IP4 192.0.2.2
s=-
c=IN IP4 192.0.2.2
t=0 0
m=audio 1296 RTP/AVP 0
The ModifyConnection command does not repeat the
LocalConnectionOptions sent previously. As far as fax handling is
concerned, the gateway therefore attempts to continue using the
current fax handling procedure, i.e. loose Call Agent controlled
T.38. The T.38 loose procedure can always be supported, and hence a
switch to T.38 will be attempted if the originating gateway detects
a fax call.
Step 7:
The gateway acknowledges the command. At this point, a call is
established using PCMU encoding, and if a fax call is detected, the
Call Agent controlled T.38 procedure will be initiated.
Step 8-9:
A fax call now occurs. First, the T.30 CED tone (a.k.a. V.25 ANS)
is sent which in this case is simply passed through the current PCMU
encoding. Since both fax and modem calls can start with this
sequence, it is not possible to determine that this is a fax call
until step 9, where the V.21 fax preamble is detected.
Andreasen/Hancock Informational - Expires September 2008 34
MGCP Fax Package March 2008
Step 10:
The terminating SIP UA in fact does support T.38, and upon detecting
the fax call, it attempts to change to T.38. Consequently, it sends
a re-INVITE to the originating Call Agent with an updated SDP
indicating a switch to T.38.
INVITE sip:ca@ca-o.whatever.net SIP/2.0
...
Content-Type: application/sdp
Content-Length: 100
v=0
o=- 25678 753850 IN IP4 192.0.2.2
s=-
c=IN IP4 192.0.2.2
t=0 0
m=image 1296 udptl t38
Step 11:
The originating Call Agent then sends a ModifyConnection command to
the originating gateway:
MDCX 1003 ds/ds1-1/1@gw-o.whatever.net MGCP 1.0
C: 1
I: 1
v=0
o=- 25678 753850 IN IP4 192.0.2.2
s=-
c=IN IP4 192.0.2.2
t=0 0
m=image 1296 udptl t38
Step 12:
The originating gateway changes to T.38 and sends back a success
response with updated SDP:
200 1003 OK
v=0
o=- 25678 753850 IN IP4 192.0.2.1
s=-
c=IN IP4 192.0.2.1
t=0 0
m=image 3456 udptl t38
a=sqn: 0
a=cdsc: 1 audio RTP/AVP 0 18
a=cdsc: 3 image udptl t38
Step 13:
Andreasen/Hancock Informational - Expires September 2008 35
MGCP Fax Package March 2008
The originating Call Agent sends a SIP 200 OK response with the
updated SDP to the terminating SIP User Agent:
SIP/2.0 200 OK
...
Content-Type: application/sdp
Content-Length: 167
v=0
o=- 25678 753850 IN IP4 192.0.2.1
s=-
c=IN IP4 192.0.2.1
t=0 0
m=image 3456 udptl t38
a=sqn: 0
a=cdsc: 1 audio RTP/AVP 0 18
a=cdsc: 3 image udptl t38
Step 14:
The terminating SIP User Agent receives the SIP 200 and sends a SIP
ACK.
Since the terminating SIP User Agent now has a
RemoteConnectionDescriptor with "image/t38" as valid media, it can
start exchanging T.38 with the originating gateway (and vice versa).
Step 15, 16:
The originating endpoint detects V.21 fax preamble. Even though the
endpoint is already using "image/t38" for media, it generates a
"t38(start)" event and notifies the Call Agent.
NTFY 3500 ds/ds1-1/1@gw-o.whatever.net MGCP 1.0
O: fxr/t38(start)
X: 1
Step 17, 18:
The Call Agent acknowledges the Notify command and then issues a new
request for notification of the T38 event.
200 3500 OK
.
RQNT 1004 ds/ds1-1/1@gw-o.whatever.net MGCP 1.0
R: fxr/t38
X: 2
Step 19:
The gateway acknowledges the command.
Andreasen/Hancock Informational - Expires September 2008 36
MGCP Fax Package March 2008
200 1004 OK
Step 20-22:
When the fax ends, the terminating SIP UA decides to tear down the
call and hence sends a SIP BYE message, which the Call Agent
responds to with a SIP 200.
Step 23:
The originating endpoint also generates a "t38(stop)" event, which
is notified to the Call Agent:
NTFY 3502 ds/ds1-1/1@gw-o.whatever.net MGCP 1.0
O: t38(stop)
X: 2
Step 24:
The Call Agent acknowledges the Notify command:
200 3502 OK
The fax call is now over. The Call Agent may now decide to change
back to a voice codec, delete the connection, or something
different.
4. Security Considerations
The MGCP fax package itself is not known to introduce any new
security concerns. However, implementers should note that T.38
media is currently transported over UDP (UDPTL) or TCP in the clear
and without any integrity protection. If for example security
services are in place to protect RTP media streams, these will thus
not be in effect for the T.38 media stream. If such lack of
security is a concern, the fax LocalConnectionOptions allowing T.38
in this package SHOULD NOT be used, i.e. the "off" (or a new secure
extension) fax LocalConnectionOption should be used.
5. IANA Considerations
The IANA is hereby requested to register the following MGCP package:
Package Title Name Version
------------- ---- -------
Fax FXR 0
6. Summary of Changes
Changes since -03:
* Boiler plate updated per RFC 3978 and RFC 3979.
Andreasen/Hancock Informational - Expires September 2008 37
MGCP Fax Package March 2008
* Clarified that Fax LCO values are ordered by preference with
caveats around the "gateway" procedure (Section 2.1) .
* Added cautionary note around omitting both LCOs and a
RemoteConnectionDescriptor in CreateConnection (Section 2.1).
* Added "t38-loose" to list of values that may be omitted when
auditing capabilities (Section 2.1).
* Upgraded use of RFC 3407 capability declarations to MUST (Section
2.1.1)
* Clarified that muting of media applies to both the send and
receive direction (Section 2.1.1).
* Clarified that timeouts may also occur while waiting for the call
agent to switch to "image/t38" (Section 2.11).
* Defined how a call agent can abort a T.38 procedure (Section
2.1.1).
* Added new Section 2.1.5 on detecting a fax call.
* Added new Section 2.1.6 on considerations for which procedure to
request.
* Clarified when and how the T38(start), T38(stop), and T38(failure)
events are generated (Section 2.2.3).
* Added new Section 2.4 on Negotiation of T.38 Parameters.
* Added new Implementation Considerations in Section 2.5.
* Added new example call flow showing interaction with SIP endpoints
(Section 3.3.)
7. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3435] F. Andreasen, B. Foster, "Media Gateway Control
Protocol (MGCP) Version 1.0", RFC 3435, January 2003.
[T38] ITU-T Recommendation T.38, "Procedures for real-time
Group 3 facsimile communication over IP networks", 03/2002.
[RFC3407] F. Andreasen, "Session Description Protocol (SDP)
Simple Capability Declaration", RFC 3407, October 2002.
8. Informative References
Andreasen/Hancock Informational - Expires September 2008 38
MGCP Fax Package March 2008
[T30] ITU-T Recommendation T.30, "Procedures for document
facsimile transmission in the general switched telephone network",
07/03.
[RFC3261] J. Rosenberg, H. Schulzrinne, G. Camarillo, A.
Johnston, J. Peterson, R. Sparks, M. Handley, E. Schooler, "SIP:
Session Initiation Protocol", RFC 3261, June 2002.
9. Acknowledgements
Several people have contributed to the development of the MGCP fax
package. In particular, the author would like to thank Bill Foster,
Paul Jones, Gary Kelly, Rajesh Kumar, Dave Horwitz, Hiroshi Tamura,
Rob Thompson and the CableLabs PacketCable NCS focus team for their
contributions.
10. Author's Address
Flemming Andreasen
Cisco Systems
499 Thornall Street, 8th Floor
Edison, NJ 08837
Email: fandreas@cisco.com
David Hancock
CableLabs
858 Coal Creek Circle
Louisville, CO 80027
Email: d.hancock@cablelabs.com
Andreasen/Hancock Informational - Expires September 2008 39
MGCP Fax Package March 2008
Full Copyright Statement
Copyright (C) The IETF Trust (2008).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on
an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE
REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE
IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY
WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE
ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE.
Disclaimer of validity
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed
to pertain to the implementation or use of the technology described
in this document or the extent to which any license under such
rights might or might not be available; nor does it represent that
it has made any independent effort to identify any such rights.
Information on the procedures with respect to rights in RFC
documents can be found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use
of such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository
at http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgment
Funding for the RFC Editor function is currently provided by the
Internet Society.
Andreasen/Hancock Informational - Expires September 2008 40 | PAFTECH AB 2003-2026 | 2026-04-24 01:44:15 |