One document matched: draft-aboba-radext-wlan-08.txt
Differences from draft-aboba-radext-wlan-07.txt
Network Working Group Bernard Aboba
INTERNET-DRAFT Microsoft Corporation
Category: Proposed Standard Jouni Malinen
Expires: December 2, 2008 Devicescape Software
Paul Congdon
Hewlett Packard Company
Joseph Salowey
Cisco Systems
2 June 2008
RADIUS Attributes for IEEE 802 Networks
draft-aboba-radext-wlan-08.txt
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on December 2, 2008.
Copyright Notice
Copyright (C) The IETF Trust (2008). All Rights Reserved.
Abstract
RFC 3580 provides guidelines for the use of the Remote Authentication
Dialin User Service (RADIUS) within IEEE 802 local area networks
(LANs). This document proposes additional attributes for use within
IEEE 802 networks. The attributes defined in this document are
usable both within RADIUS and Diameter.
Aboba, et al. Proposed Standard [Page 1]
INTERNET-DRAFT RADIUS Attributes for IEEE 802 2 June 2008
Table of Contents
1. Introduction .......................................... 3
1.1 Terminology ..................................... 3
1.2 Requirements Language ........................... 4
2. RADIUS attributes ..................................... 4
2.1 Allowed-Called-Station-Id ....................... 4
2.2 EAP-Key-Name .................................... 5
2.3 EAP-Peer-Id ..................................... 6
2.4 EAP-Server-Id ................................... 7
2.5 Mobility-Domain-Id .............................. 8
2.6 Mesh-Key-Distributor-Domain-Id .................. 9
2.7 Preauth-Timeout ................................. 10
2.8 EAP-Lower-Layer ................................. 10
2.9 Network-Id-Name ................................. 11
3. Table of attributes ................................... 12
4. Diameter Considerations ............................... 13
5. IANA Considerations ................................... 14
6. Security Considerations ............................... 15
7. References ............................................ 15
7.1 Normative References .................................. 15
7.2 Informative References ................................ 16
ACKNOWLEDGMENTS .............................................. 17
AUTHORS' ADDRESSES ........................................... 18
Full Copyright Statement ..................................... 19
Intellectual Property ........................................ 19
Aboba, et al. Proposed Standard [Page 2]
INTERNET-DRAFT RADIUS Attributes for IEEE 802 2 June 2008
1. Introduction
In situations where it is desirable to centrally manage
authentication, authorization and accounting (AAA) for IEEE 802
[IEEE-802] networks, deployment of a backend authentication and
accounting server is desirable. In such situations, it is expected
that IEEE 802 authenticators will function as AAA clients.
RFC 3580 [RFC3580] defined guidelines for the use of the Remote
Authentication Dialin User Service (RADIUS) within networks utilizing
IEEE 802 local area networks. This document defines additional
attributes suitable for usage by IEEE 802 authenticators acting as
AAA clients. The attributes defined in this document are usable both
within RADIUS and Diameter.
1.1. Terminology
This document uses the following terms:
Access Point (AP)
A Station that provides access to the distribution
services via the wireless medium for associated Stations.
Association The service used to establish Access Point/Station
mapping and enable Station invocation of the distribution
system services.
authenticator An authenticator is an entity that require authentication
from the supplicant. The authenticator may be connected
to the supplicant at the other end of a point-to-point
LAN segment or wireless link.
authentication server
An authentication server is an entity that provides an
authentication service to an authenticator. This service
verifies from the credentials provided by the supplicant,
the claim of identity made by the supplicant.
Station (STA) Any device that contains an IEEE 802.11 conformant medium
access control (MAC) and physical layer (PHY) interface
to the wireless medium (WM).
Supplicant A supplicant is an entity that is being authenticated by
an authenticator. The supplicant may be connected to the
authenticator at one end of a point-to-point LAN segment
or 802.11 wireless link.
Aboba, et al. Proposed Standard [Page 3]
INTERNET-DRAFT RADIUS Attributes for IEEE 802 2 June 2008
1.2. Requirements Language
In this document, several words are used to signify the requirements
of the specification. The key words "MUST", "MUST NOT", "REQUIRED",
"SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY",
and "OPTIONAL" in this document are to be interpreted as described in
[RFC2119].
2. RADIUS attributes
2.1. Allowed-Called-Station-Id
Description
The Allowed-Called-Station-Id Attribute allows the RADIUS server
to specify which Called-Station-Ids and networks the user is
allowed to access. One or more Allowed-Called-Station-Id
attributes MAY be included in an Access-Accept or CoA-Request
packet.
If none of the networks encoded in Allowed-Called-Station-Id
attributes correspond to the network selected by the user (e.g. if
none of the Allowed-Called-Station-Id attributes include the
network name included in a Network-Id-Name attribute sent in the
Access-Request), then this implies that the network selection
request made by the user could not be honored.
A summary of the Allowed-Called-Station-Id Attribute format is
shown below. The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | String...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Code
TBD
Length
>=3
String
The String field is one or more octets, containing the layer 2
endpoint that the user's call is allowed to be terminated on, as
Aboba, et al. Proposed Standard [Page 4]
INTERNET-DRAFT RADIUS Attributes for IEEE 802 2 June 2008
specified in the definition of Called-Station-Id in [RFC2865]
Section 5.30 and [RFC3580] Section 3.20. In the case of IEEE 802,
the Allowed-Called-Station-Id Attribute is used to store the
Medium Access Control (MAC) address in ASCII format (upper case
only), with octet values separated by a "-". Example:
"00-10-A4-23-19-C0". Where restrictions on both the network and
authenticator MAC address usage are intended, the network name
MUST be appended to the authenticator MAC address, separated from
the MAC address with a ":". Example "00-10-A4-23-19-C0:AP1".
Where no MAC address restriction is intended, the MAC address
field MUST be omitted, but network name field MUST be included.
Example "AP1". Within IEEE 802.11 [IEEE-802.11], the SSID
constitutes the network name; within IEEE 802.1X-REV [IEEE-802.1X-
REV], the Network-Id Name (NID-Name) constitutes the network name.
If the user attempts to connect to the NAS from a Called-Station-
Id that does not match one of the Allowed-Called-Station-Id
attributes, then the user MUST NOT be permitted to access the
network.
The Allowed-Called-Station-Id Attribute is useful in the following
situations where it can be desirable for the RADIUS server to
restrict usage of key cache entries:
[1] Where users can connect to a NAS without an Access-Request being
sent by the NAS to the RADIUS server (e.g. where key caching is
supported within IEEE 802.11 or IEEE 802.1X-REV [IEEE-802.1X-
REV]).
[2] Where pre-authentication may be supported (e.g. IEEE 802.1X
pre-authentication). In this situation, the network name
typically will not be included in a Called-Station-Id Attribute
within the Access-Request, so that the RADIUS server will not be
able to make a decision whether to allow access to a particular
network.
2.2. EAP-Key-Name
Description
The EAP-Key-Name Attribute, defined in [RFC4072], contains the EAP
Session-Id, as described in [RFCKEY]. Exactly how this Attribute
is used depends on the link layer in question.
It should be noted that not all link layers use this name and
existing EAP method implementations do not generate it. An EAP-
Key-Name Attribute MAY be included within Access-Request, Access-
Accept and CoA-Request packets. A summary of the EAP-Key-Name
Aboba, et al. Proposed Standard [Page 5]
INTERNET-DRAFT RADIUS Attributes for IEEE 802 2 June 2008
Attribute format is shown below. The fields are transmitted from
left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | String...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Code
102 [RFC4072]
Length
>=2
String
The String field, when present, is one or more octets, containing
the EAP Session-Id, as defined in "Extensible Authentication
Protocol (EAP) Key Management Framework" [RFCKEY]. Since the NAS
operates as a pass-through in EAP, it cannot know the EAP Session-
Id before receiving it from the RADIUS server. As a result, an
EAP-Key-Name Attribute sent in an Access-Request MUST NOT contain
any data. A RADIUS server receiving an Access-Request with an
EAP-Key-Name Attribute containing data MUST silently discard the
Attribute. In addition, the RADIUS server SHOULD only include
this Attribute in an Access-Accept or CoA-Request if an EAP-Key-
Name Attribute was present in the Access-Request.
2.3. EAP-Peer-Id
Description
The EAP-Peer-Id Attribute contains a Peer-Id generated by the EAP
method. Exactly how this name is used depends on the link layer
in question. See [RFCKEY] for more discussion. The EAP-Peer-Id
Attribute MAY be included in Access-Request, Access-Accept and
Accounting-Request packets. More than one EAP-Peer-Id Attribute
MUST NOT be included in an Access-Request; one or more EAP-Peer-Id
attributes MAY be included in an Access-Accept.
It should be noted that not all link layers use this name, and
existing EAP method implementations do not generate it. Since the
NAS operates as a pass-through in EAP [RFC3748], it cannot know
the EAP-Peer-Id before receiving it from the RADIUS server. As a
result, an EAP-Peer-Id Attribute sent in an Access-Request MUST
Aboba, et al. Proposed Standard [Page 6]
INTERNET-DRAFT RADIUS Attributes for IEEE 802 2 June 2008
NOT contain any data. A home RADIUS server receiving an Access-
Request an EAP-Peer-Id Attribute with non-empty data MUST silently
discard the Attribute. In addition, the home RADIUS server SHOULD
include one or more EAP-Peer-Id attributes in an Access-Accept
only if an empty EAP-Peer-Id Attribute was present in the Access-
Request. A summary of the EAP-Peer-Id Attribute format is shown
below. The fields are transmitted from left to right.
Aboba, et al. Proposed Standard [Page 7]
INTERNET-DRAFT RADIUS Attributes for IEEE 802 2 June 2008
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | String...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Code
TBD
Length
>=2
String
The String field, when present, is one or more octets containing a
EAP Peer-Id exported by the EAP method. For details, see [RFCKEY]
Appendix A. A robust implementation SHOULD support the field as
undistinguished octets.
2.4. EAP-Server-Id
Description
The EAP-Server-Id Attribute contains a Server-Id generated by the
EAP method. Exactly how this name is used depends on the link
layer in question. See [RFCKEY] for more discussion. The EAP-
Server-Id Attribute is only allowed in Access-Request, Access-
Accept, and Accounting-Request packets. More than one EAP-Server-
Id Attribute MUST NOT be included in an Access-Request; one or
more EAP-Server-Id attributes MAY be included in an Access-Accept.
It should be noted that not all link layers use this name, and
existing EAP method implementations do not generate it. Since the
NAS operates as a pass-through in EAP [RFC3748], it cannot know
the EAP-Server-Id before receiving it from the RADIUS server. As
a result, an EAP-Server-Id Attribute sent in an Access-Request
MUST NOT contain any data. A home RADIUS server receiving in an
Access-Request an EAP-Server-Id Attribute with non-empty data MUST
silently discard the Attribute. In addition, the home RADIUS
server SHOULD include this Attribute an Access-Accept only if an
empty EAP-Server-Id Attribute was present in the Access-Request.
A summary of the EAP-Server-Id Attribute format is shown below.
The fields are transmitted from left to right.
Aboba, et al. Proposed Standard [Page 8]
INTERNET-DRAFT RADIUS Attributes for IEEE 802 2 June 2008
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | String...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Code
TBD
Length
>=2
String
The String field, when present, is one or more octets, containing
a EAP Server-Id exported by the EAP method. For details, see
[RFCKEY] Appendix A. A robust implementation SHOULD support the
field as undistinguished octets.
2.5. Mobility-Domain-Id
Description
A single Mobility-Domain-Id Attribute MAY be included in an
Access-Request or Accounting-Request, in order to enable the NAS
to provide the RADIUS server with the Mobility Domain Identifier
(MDID), defined in IEEE 802.11r [IEEE-802.11r]. A summary of the
Mobility-Domain-Id Attribute format is shown below. The fields
are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Value
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Value |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Code
TBD
Length
=6
Aboba, et al. Proposed Standard [Page 9]
INTERNET-DRAFT RADIUS Attributes for IEEE 802 2 June 2008
Value
The Value field is four octets. Since the Mobility Domain
Identifier defined in IEEE 802.11r [IEEE-802.11r] is only two
octets in length, the two most significant octets MUST be set to
zero by the sender, and are ignored by the receiver; the two
least significant octets contain the MDID value.
2.6. Mesh-Key-Distributor-Domain-Id
Description
A single Mesh-Key-Distributor-Domain-Id Attribute MAY be included
in an Access-Request or Accounting-Request, in order to enable the
NAS to provide the RADIUS server with the Mesh Key Distributor
Domain Identifier (MKDD-ID), defined in IEEE 802.11s
[IEEE-802.11s]. A summary of the Mesh-Key-Distributor-Domain-Id
Attribute format is shown below. The fields are transmitted from
left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Value
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Value (cont)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Value (cont) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Code
TBD
Length
10
Value
The Value field contains eight octets, encoding a single Mesh Key
Distributor Domain Identifier (MKDD-ID) as defined in IEEE 802.11s
[IEEE-802.11s]. Since the MKDD-ID defined in IEEE 802.11s is six
octets in length, the two most significant octets MUST be set to
zero by the sender and are ignored by the receiver.
Aboba, et al. Proposed Standard [Page 10]
INTERNET-DRAFT RADIUS Attributes for IEEE 802 2 June 2008
2.7. Preauth-Timeout
Description
This Attribute sets the maximum number of seconds which pre-
authentication state is kept by the NAS. This Attribute MAY be
sent by the server to the NAS in an Access-Accept. Where both
Session-Timeout and Preauth-Timeout attributes are present in an
Access-Accept, the Session-Timeout Attribute refers only to the
maximum session time after the supplicant associates with the
authenticator and is enabled to send data frames through it. A
summary of the Preauth-Timeout Attribute format is shown below.
The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Value
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Value (cont) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Code
TBD
Length
6
Value
The field is 4 octets, containing a 32-bit unsigned integer with
the maximum number of seconds that pre-authentication state should
be retained by the NAS.
2.8. EAP-Lower-Layer
Description
This Attribute indicates the lower layer over which EAP is
transported. This Attribute MAY be sent by the NAS to the RADIUS
server in an Access-Request or an Accounting-Request packet. A
summary of the EAP-Lower-Layer Attribute format is shown below.
The fields are transmitted from left to right.
Aboba, et al. Proposed Standard [Page 11]
INTERNET-DRAFT RADIUS Attributes for IEEE 802 2 June 2008
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Value
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Value (cont) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Code
TBD
Length
6
Value
The field is 4 octets, containing the following values:
1 - Wired IEEE 802.1X Version 1 (2001)
2 - Wired IEEE 802.1X Version 2 (2004) [IEEE-802.1X]
3 - Wired IEEE 802.1X Version 3 [IEEE-802.1X-REV]
4 - WPA
5 - WPA2 (no pre-authentication)
6 - WPA2, IEEE 802.1X pre-authentication
7 - IEEE 802.11r
8 - IEEE 802.11s
9 - IEEE 802.16e
10 - IKEv2
11 - PPP
12 - PANA (no pre-authentication)
2.9. Network-Id-Name
Description
The Network-Id-Name Attribute is utilized by implementations of
IEEE-802.1X-REV [IEEE-802.1X-REV] to specify the name of a
Network-Id (NID-Name) selected by the Supplicant.
Unlike the IEEE 802.11 SSID (which is a maximum of 32 octets in
length), the NID-Name may be up to 253 octets in length.
Consequently, if the MAC address is included within the Called-
Station-Id Attribute, it is possible that there will not be enough
remaining space to encode the NID-Name as well. Therefore when
used with IEEE 802.1X-REV, the Called-Station-Id Attribute SHOULD
contain only the MAC address, with the Network-Id-Name Attribute
Aboba, et al. Proposed Standard [Page 12]
INTERNET-DRAFT RADIUS Attributes for IEEE 802 2 June 2008
used to transmit the NID-Name. The Network-Id-Name Attribute
SHOULD NOT be used to encode the IEEE 802.11 SSID; as noted in
[RFC3580], the Called-Station-Id Attribute is used for this
purpose.
Zero or one Network-Id-Name Attribute is permitted within a RADIUS
Access-Request or Accounting-Request packet. When included within
an Access-Request packet, the Network-Id-Name Attribute represents
the NID-Name selected by the Supplicant in the EAPoL-Start packet.
When included within an Accounting-Request packet, the Network-Id-
Name Attribute represents the NID-Name to which the Supplicant has
been given access.
In order to indicate which network names the Supplicant is
permitted to access, the Allowed-Called-Station-Id Attribute is
used.
A summary of the Network-Id-Name Attribute format is shown below.
The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | String...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Code
TBD
Length
>=2
String
The String field, when present, is one or more octets, containing
a NID-Name. For details, see [IEEE-802.1X-REV]. A robust
implementation SHOULD support the field as undistinguished octets.
Aboba, et al. Proposed Standard [Page 13]
INTERNET-DRAFT RADIUS Attributes for IEEE 802 2 June 2008
3. Table of attributes
The following table provides a guide to which attributes may be found
in which kinds of packets, and in what quantity.
Access- Access- Access- Access-
Request Accept Reject Challenge # Attribute
0 0+ 0 0 TBD Allowed-Called-Station-Id
0-1 0-1 0 0 102 EAP-Key-Name
0-1 0+ 0 0 TBD EAP-Peer-Id
0-1 0+ 0 0 TBD EAP-Server-Id
0-1 0 0 0 TBD Mobility-Domain-Id
0-1 0 0 0 TBD Mesh-Key-Distributor-Domain-Id
0-1 0-1 0 0 TBD Preauth-Timeout
0-1 0 0 0 TBD EAP-Lower-Layer
0-1 0 0 0 TBD Network-Id-Name
CoA- Acct-
Req Req # Attribute
0+ 0 TBD Allowed-Called-Station-Id
0-1 0 102 EAP-Key-Name
0 0+ TBD EAP-Peer-Id
0 0+ TBD EAP-Server-Id
0 0-1 TBD Mobility-Domain-Id
0 0-1 TBD Mesh-Key-Distributor-Domain-Id
0 0 TBD Preauth-Timeout
0 0-1 TBD EAP-Lower-Layer
0 0-1 TBD Network-Id-Name
The following table defines the meaning of the above table entries.
0 This Attribute MUST NOT be present in packet.
0+ Zero or more instances of this Attribute MAY be
present in the packet.
0-1 Zero or one instance of this Attribute MAY be
present in the packet.
4. Diameter Considerations
The EAP-Key-Name Attribute is already defined as a RADIUS Attribute
within Diameter EAP [RFC4072]. When used in Diameter, the other
attributes defined in this specification can be used as Diameter AVPs
from the Code space 1-255 (RADIUS Attribute compatibility space). No
additional Diameter Code values are therefore allocated. The data
types and flag rules for the attributes are as follows:
Aboba, et al. Proposed Standard [Page 14]
INTERNET-DRAFT RADIUS Attributes for IEEE 802 2 June 2008
+---------------------+
| AVP Flag rules |
|----+-----+----+-----|----+
| | |SHLD| MUST| |
Attribute Name Value Type |MUST| MAY | NOT| NOT|Encr|
-----------------------------------------|----+-----+----+-----|----|
Allowed-Called- | | | | | |
Station-Id UTF8String | M | P | | V | Y |
EAP-Peer-Id UTF8String | M | P | | V | Y |
EAP-Server-Id UTF8String | M | P | | V | Y |
Mobility-Domain-Id Unsigned32 | | P | | V | Y |
Mesh-Key- | | | | | |
Distributor-Domain-Id Unsigned32 | | P | | V | Y |
Preauth-Timeout Unsigned32 | M | P | | V | Y |
EAP-Lower-Layer Unsigned32 | M | P | | V | Y |
Network-Id-Name UTF8String | M | P | | V | Y |
-----------------------------------------|----+-----+----+-----|----|
The attributes in this specification have no special translation
requirements for Diameter to RADIUS or RADIUS to Diameter gateways;
they are copied as is, except for changes relating to headers,
alignment, and padding. See also [RFC3588] Section 4.1 and [RFC4005]
Section 9.
What this specification says about the applicability of the
attributes for RADIUS Access-Request packets applies in Diameter to
AA-Request [RFC4005] or Diameter-EAP-Request [RFC4072]. What is said
about Access-Challenge applies in Diameter to AA-Answer [RFC4005] or
Diameter-EAP-Answer [RFC4072] with Result-Code AVP set to
DIAMETER_MULTI_ROUND_AUTH.
What is said about Access-Accept applies in Diameter to AA-Answer or
Diameter-EAP-Answer messages that indicate success. Similarly, what
is said about RADIUS Access-Reject packets applies in Diameter to AA-
Answer or Diameter-EAP-Answer messages that indicate failure.
What is said about COA-Request applies in Diameter to Re-Auth-Request
[RFC4005]. What is said about Accounting-Request applies to Diameter
Accounting- Request [RFC4005] as well.
5. IANA Considerations
This document uses the RADIUS [RFC2865] namespace, see
<http://www.iana.org/assignments/radius-types>. This specification
requires assignment of a RADIUS attribute types for the following
attributes:
Aboba, et al. Proposed Standard [Page 15]
INTERNET-DRAFT RADIUS Attributes for IEEE 802 2 June 2008
Attribute Type
========= ====
Allowed-Called-Station-Id TBD
EAP-Peer-Id TBD
EAP-Server-Id TBD
Mobility-Domain-Id TBD
Mesh-Key-Distributor-Domain-Id TBD
Preauth-Timeout TBD
EAP-Lower-Layer TBD
Network-Id-Name TBD
This specification allocates the following decimal values for the
EAP-Lower-Layer Attribute:
1 - Wired IEEE 802.1X Version 1 (2001)
2 - Wired IEEE 802.1X Version 2 (2004)
3 - Wired IEEE 802.1X Version 3
4 - WPA
5 - WPA2 (no pre-authentication)
6 - WPA2, IEEE 802.1X pre-authentication
7 - IEEE 802.11r
8 - IEEE 802.11s
9 - IEEE 802.16e
10 - IKEv2
11 - PPP
12 - PANA (no pre-authentication)
Additional values are allocated as described in [RFC3575] Section 2.1
(Designated Expert).
6. Security Considerations
Since this document describes the use of RADIUS for purposes of
authentication, authorization, and accounting in IEEE 802 networks,
it is vulnerable to all of the threats that are present in other
RADIUS applications. For a discussion of these threats, see
[RFC2607], [RFC2865], [RFC3162], [RFC3579], [RFC3580] and [RFC5176].
7. References
7.1. Normative references
[IEEE-802] IEEE Standards for Local and Metropolitan Area Networks:
Overview and Architecture, ANSI/IEEE Std 802, 1990.
[IEEE-802.11] Information technology - Telecommunications and
information exchange between systems - Local and
metropolitan area networks - Specific Requirements Part
Aboba, et al. Proposed Standard [Page 16]
INTERNET-DRAFT RADIUS Attributes for IEEE 802 2 June 2008
11: Wireless LAN Medium Access Control (MAC) and
Physical Layer (PHY) Specifications, IEEE Std.
802.11-2007, 2007.
[IEEE-802.11r] Draft Amendment to Standard for Information technology -
Telecommunications and information exchange between
systems - Local and metropolitan area networks - Specific
Requirements Part 11: Wireless LAN Medium Access Control
(MAC) and Physical Layer (PHY) Specifications: Amendment
2: Fast BSS Transition, IEEE P802.11r/D9.0, March 2008.
[IEEE-802.11s] Draft Amendment to Standard for Information technology -
Telecommunications and information exchange between
systems - Local and metropolitan area networks - Specific
Requirements Part 11: Wireless LAN Medium Access Control
(MAC) and Physical Layer (PHY) Specifications: Amendment
4: Mesh Networking, IEEE P802.11s/D1.10, March 2008.
[IEEE-802.1X-REV]
Draft Standard for Local and Metropolitan Area Networks -
Port-Based Network Access Control, D2.5, May 2008.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", RFC 2119, March, 1997.
[RFC2865] Rigney, C., Rubens, A., Simpson, W. and S. Willens,
"Remote Authentication Dial In User Service (RADIUS)",
RFC 2865, June 2000.
[RFC3575] Aboba, B., "IANA Considerations for RADIUS", RFC 3575,
July 2003.
[RFC3588] Calhoun, P., Loughney, J., Guttman, E., Zorn, G., and J.
Arkko, "Diameter Base Protocol", RFC 3588, September
2003.
[RFC4072] Eronen, P., Hiller, T. and G. Zorn, "Diameter Extensible
Authentication Protocol (EAP) Application", RFC 4072,
August 2005.
[RFCKEY] Aboba, B., Simon, D. and P. Eronen, "EAP Key Management
Framework", draft-ietf-eap-keying-22.txt, November 2007.
7.2. Informative references
[IEEE-802.1X] IEEE Standards for Local and Metropolitan Area Networks:
Port based Network Access Control, IEEE Std 802.1X-2004,
December 2004.
Aboba, et al. Proposed Standard [Page 17]
INTERNET-DRAFT RADIUS Attributes for IEEE 802 2 June 2008
[RFC2607] Aboba, B. and J. Vollbrecht, "Proxy Chaining and Policy
Implementation in Roaming", RFC 2607, June 1999.
[RFC3162] Aboba, B., Zorn, G. and D. Mitton, "RADIUS and IPv6", RFC
3162, August 2001.
[RFC3575] Aboba, B., "IANA Considerations for RADIUS", RFC 3575,
July 2003.
[RFC3579] Aboba, B. and P. Calhoun, "RADIUS Support for Extensible
Authentication Protocol (EAP)", RFC 3579, September 2003.
[RFC3580] Congdon, P., Aboba, B., Smith, A., Zorn, G. and J. Roese,
"IEEE 802.1X Remote Authentication Dial In User Service
(RADIUS) Usage Guidelines", RFC 3580, September 2003.
[RFC3748] Aboba, B., Blunk, L., Vollbrecht, J., Carlson, J. and H.
Levkowetz, "Extensible Authentication Protocol (EAP)",
RFC 3748, June 2004.
[RFC4005] Calhoun, P., Zorn, G., Spence, D., and D. Mitton,
"Diameter Network Access Server Application", RFC 4005,
August 2005.
[RFC5176] Chiba, M., Dommety, G., Eklund, M., Mitton, D. and B.
Aboba, "Dynamic Authorization Extensions to Remote
Authentication Dial In User Service (RADIUS)", RFC 5176,
January 2008.
Acknowledgments
The authors would like to acknowledge Dorothy Stanley of Aruba
Networks, Yoshihiro Ohba of Toshiba, and the contributors to the IEEE
802.11 review of this document, for useful discussions.
Aboba, et al. Proposed Standard [Page 18]
INTERNET-DRAFT RADIUS Attributes for IEEE 802 2 June 2008
Authors' Addresses
Bernard Aboba
Microsoft Corporation
One Microsoft Way
Redmond, WA 98052
EMail: bernarda@microsoft.com
Phone: +1 425 706 6605
Fax: +1 425 936 7329
Jouni Malinen
Devicescape Software, Inc.
900 Cherry Avenue
San Bruno, CA 94066
EMail: jkm@devicescape.com
Phone: +1 650 829 2600
Fax: +1 650 829 2601
Paul Congdon
Hewlett Packard Company
HP ProCurve Networking
8000 Foothills Blvd, M/S 5662
Roseville, CA 95747
Phone: +1 916 785 5753
Fax: +1 916 785 8478
EMail: paul_congdon@hp.com
Joseph Salowey
Cisco Systems
Email: jsalowey@cisco.com
Aboba, et al. Proposed Standard [Page 19]
INTERNET-DRAFT RADIUS Attributes for IEEE 802 2 June 2008
Full Copyright Statement
Copyright (C) The IETF Trust (2008).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgment
Funding for the RFC Editor function is provided by the IETF
Administrative Support Activity (IASA).
Aboba, et al. Proposed Standard [Page 20]
INTERNET-DRAFT RADIUS Attributes for IEEE 802 2 June 2008
Open issues
Open issues relating to this specification are tracked on the
following web site:
http://www.drizzle.com/~aboba/RADEXT/
Aboba, et al. Proposed Standard [Page 21]
| PAFTECH AB 2003-2026 | 2026-04-22 14:57:00 |