One document matched: draft-rtgyangdt-rtgwg-ni-model-00.xml
<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE rfc SYSTEM "rfc2629.dtd" [
]>
<?xml-stylesheet type='text/xsl' href='rfc2629.xslt' ?>
<?rfc toc="yes" ?>
<?rfc symrefs="yes" ?>
<?rfc sortrefs="yes"?>
<?rfc iprnotified="no" ?>
<?rfc strict="yes" ?>
<rfc category="std" ipr="trust200902" docName="draft-rtgyangdt-rtgwg-ni-model-00" >
<front>
<title abbrev="LNE Model">Network Instance Model</title>
<author initials='L.' surname="Berger" fullname='Lou Berger'>
<organization>LabN Consulting, L.L.C.</organization>
<address>
<email>lberger@labn.net</email>
</address>
</author>
<author initials='C.' surname="Hopps" fullname='Christan Hopps'>
<organization>Deutsche Telekom</organization>
<address>
<email>chopps@chopps.org</email>
</address>
</author>
<author initials='A.' surname="Lindem" fullname='Acee Lindem'>
<organization>Cisco Systems</organization>
<address>
<postal>
<street>301 Midenhall Way</street>
<city>Cary</city> <region>NC</region>
<country>USA</country>
<code>27513</code>
</postal>
<email>acee@cisco.com</email>
</address>
</author>
<author initials='D.' surname="Bogdanovic" fullname='Dean Bogdanovic'>
<organization></organization>
<address>
<email>ivandean@gmail.com</email>
</address>
</author>
<date/>
<abstract>
<t>
This document defines a network instance module. This module along
with the logical network element module can be used to manage the
logical and virtual resource representations that may be present on a
network device. Examples of common industry terms for logical resource
representations are Logical Systems or Logical Routers. Examples of
common industry terms for virtual resource representations are Virtual
Routing and Forwarding (VRF) instances and Virtual Switch Instances
(VSIs).
</t>
</abstract>
</front>
<middle>
<section anchor="sec-1" title="Introduction">
<t>
This document defines the second of two new modules that are defined
to support the configuration and operation of network-devices that
allow for the partitioning of resources from both, or either,
management and networking perspectives. Both make use of emerging
YANG functionality supported by YANG Schema Mount <xref
target="I-D.ietf-netmod-schema-mount"/>. This document is expected to use whatever
Schema Mount solution is agreed upon by the Netmod Working Group.
</t>
<t>
Two forms of resource partitioning are supported:
</t>
<t>
The first form, which is defined in <xref target="LNE-MODEL"/>,
provides a logical partitioning of a network device where each
partition is separately managed as essentially an independent
network element which is 'hosted' by the base network device.
These hosted network elements are referred to as logical
network elements, or LNEs, and are supported by the
logical-network-element module defined in <xref target="LNE-MODEL"/>.
The module is used to identify LNEs and associate resources from the
network-device with each LNE. LNEs themselves are represented
in YANG as independent network devices; each accessed
independently. Optionally, and when supported by the
implementation, they may also be accessed from the host system.
Examples of vendor terminology for an LNE include logical
system or logical router, and virtual switch, chassis, or fabric.
</t>
<t>
The second form, which is defined in this document, provides
support what is commonly referred to as Virtual Routing and
Forwarding (VRF) instances as well as Virtual Switch Instances
(VSI), see <xref target="RFC4026"/>. In this form of resource
partitioning multiple control plane and forwarding/bridging
instances are provided by and managed via a single (physical or
logical) network device. This form of resource partitioning is
referred to as Network Instances and are supported by the
network-instance module defined below. Configuration and
operation of each network-instance is always via the network
device and the network-instance module.
</t>
<t>
This document was motivated by, and derived from,
<xref target="RTG-DEVICE-MODEL"/>.
</t>
<section anchor="sec-1.1" title="Status of Work and Open Issues">
<t>
The top open issues are:
<list style="numbers">
<t>This document will need to match the evolution and
standardization of <xref target="I-D.openconfig-netmod-opstate"/> or
<xref target="I-D.ietf-netmod-opstate-reqs"/> by the Netmod WG.
</t>
</list>
</t>
</section>
</section>
<section anchor="sec-2" title="Overview">
<t>
In this document, we consider network devices that support protocols
and functions defined within the IETF Routing Area, e.g, routers,
firewalls and hosts. Such devices may be physical or virtual, e.g., a
classic router with custom hardware or one residing within a
server-based virtual machine implementing a virtual network function
(VNF). Each device may sub-divide their resources into logical
network elements (LNEs) each of which provides a managed logical
device. Examples of vendor terminology for an LNE include logical
system or logical router, and virtual switch, chassis, or fabric. Each
LNE may also support virtual routing and forwarding (VRF) and virtual
switching instance (VSI) functions, which are referred to below as a
network instances (NIs). This breakdown is represented in
Figure 1.
</t>
<t>
<figure>
<artwork>
,''''''''''''''''''''''''''''''''''''''''''''''`.
| Network Device (Physical or Virtual) |
| ..................... ..................... |
| : Logical Network : : Logical Network : |
| : Element : : Element : |
| :+-----+-----+-----+: :+-----+-----+-----+: |
| :| Net | Net | Net |: :| Net | Net | Net |: |
| :|Inst.|Inst.|Inst.|: :|Inst.|Inst.|Inst.|: |
| :+-----+-----+-----+: :+-----+-----+-----+: |
| : | | | | | | : : | | | | | | : |
| :..|.|...|.|...|.|..: :..|.|...|.|...|.|..: |
| | | | | | | | | | | | | |
`'''|'|'''|'|'''|'|'''''''''|'|'''|'|'''|'|'''''
| | | | | | | | | | | |
Interfaces Interfaces
</artwork>
</figure>
</t>
<t>
Figure 1: Module Element Relationships
</t>
<t>
A model for LNEs is described in <xref target="LNE-MODEL"/> and
the model for network instances is covered in <xref
target="sec-NI"/>. For more information on how these models
may be used within an overall device model structure, see <xref
target="RTG-DEVICE-MODEL"/>.
</t>
<t>
The interface management model <xref target="RFC7223"/> is an
existing model that is impacted by the definition of LNEs and
network instances. This document and <xref target="LNE-MODEL"/>
define augmentations to the interface module to support LNEs
and NIs. Similar elements, although perhaps only for LNEs, may
also need to be included as part of the definition of the
future hardware and QoS modules.
</t>
<t>
Interfaces are a crucial part of any network device's
configuration and operational state. They generally include a
combination of raw physical interfaces, link-layer interfaces,
addressing configuration, and logical interfaces that may not
be tied to any physical interface. Several system services,
and layer 2 and layer 3 protocols may also associate
configuration or operational state data with different types of
interfaces (these relationships are not shown for simplicity).
The interface management model is defined by <xref
target="RFC7223"/>.
</t>
<t>
The logical-network-element and network-instance modules
augment the existing interface management model in two ways:
The first, by the logical-network-element module, adds an
identifier which is used on physical interface types to
identify an associated LNE. The second, by the
network-instance module, adds a name which is used on
interface or sub-interface types to identify an associated
network instance.
Similarly, this name is also added for IPv4 and IPv6 types, as
defined in <xref target="RFC7277"/>.
</t>
<t>
The interface related augmentations are as follows:
<figure>
<artwork>
module: ietf-logical-network-element
augment /if:interfaces/if:interface:
+--rw bind-lne-name? string
module: ietf-network-instance
augment /if:interfaces/if:interface:
+--rw bind-network-instance-name? string
augment /if:interfaces/if:interface/ip:ipv4:
+--rw bind-network-instance-name? string
augment /if:interfaces/if:interface/ip:ipv6:
+--rw bind-network-instance-name? string
</artwork>
</figure>
</t>
<t>
The following is an example of envisioned combined usage. The
interfaces container includes a number of commonly used
components as examples:
</t>
<t>
<figure>
<artwork>
+--rw if:interfaces
| +--rw interface* [name]
| +--rw name string
| +--rw bind-lne-name? string
| +--rw ethernet
| | +--rw ni:bind-network-instance-name? string
| | +--rw aggregates
| | +--rw rstp
| | +--rw lldp
| | +--rw ptp
| +--rw vlans
| +--rw tunnels
| +--rw ipv4
| | +--rw ni:bind-network-instance-name? string
| | +--rw arp
| | +--rw icmp
| | +--rw vrrp
| | +--rw dhcp-client
| +--rw ipv6
| +--rw ni:bind-network-instance-name? string
| +--rw vrrp
| +--rw icmpv6
| +--rw nd
| +--rw dhcpv6-client
</artwork>
</figure>
</t>
<t>
The <xref target="RFC7223"/> defined interface model is
structured to include all interfaces in a flat list, without
regard to logical or virtual instances (e.g., VRFs) supported
on the device. The bind-lne-name and
bind-network-instance-name leaves provide the association
between an interface and its associated LNE and NI (e.g., VRF
or VSI).
</t>
</section>
<section anchor="sec-NI" title=" Network Instances">
<t>
The network instance container is used to represent virtual routing
and forwarding instances (VRFs) and virtual switching instances
(VSIs), <xref target="RFC4026"/>. VRFs and VSIs are commonly used to isolate
routing and switching domains, for example to create virtual private
networks, each with their own active protocols and routing/switching
policies. The model represents both core/provider and virtual
instances. Network instances reuse and build on <xref target="I-D.ietf-netmod-routing-cfg"/>
and are shown below:
</t>
<t>
<figure>
<artwork>
module: ietf-network-instance
+--rw network-instances
+--rw network-instance* [name]
+--rw name string
+--rw type? identityref
+--rw enabled? boolean
+--rw description? string
+--rw network-instance-policy
| ...
+--rw root? schema-mount
| ...
augment /if:interfaces/if:interface:
+--rw bind-network-instance-name? string
augment /if:interfaces/if:interface/ip:ipv4:
+--rw bind-network-instance-name? string
augment /if:interfaces/if:interface/ip:ipv6:
+--rw bind-network-instance-name? string
</artwork>
</figure>
</t>
<t>
A network instance is identified by a
`name` string. This string is used both as
an index within the network-instance module and to associate
resources with a network instance as shown above in the
interface augmentation. Type is used to indicate the type NI,
such as L3-VRF, VPLS, L2-VSI, etc. Network instance policy
and root are discussed in greater detail below.
</t>
<section anchor="sec-NI.1" title=" Network Instance Policy">
<t>
Network instance policies are used to control how NI
information is represented at the device level, VRF routing
policies, and VRF/VSI identifiers. Examples include BGP route
targets (RTs) and route distinguishers (RDs), virtual network
identifiers (VN-IDs), VPLS neighbors, etc. The structure is
expected to be:
</t>
<t>
<figure>
<artwork>
module: ietf-network-instance
+--rw network-instances
+--rw network-instance* [name]
+--rw network-instance-policy
(TBD)
</artwork>
</figure>
</t>
</section>
<section anchor="sec-NI.2" title=" Network Instance Management">
<t>
Modules that may be used to represent network instance
specific information will be available under
`root`. As with LNEs, actual module
availability is expected to be implementation dependent. The
yang library module <xref target="I-D.ietf-netconf-yang-library"/>
is expected to be the primary method
used to identify supported modules. Resource related control
and assignment is expected to be managed at the network-device
level, not the network instance level, based on the
`bind-network-instance-name` augmentation
mentioned above.
</t>
<t>
As an example, consider the case where a network instance with
a `name` of "green" is defined on a network
device. In this case the following structure might be made
available:
</t>
<t>
<figure>
<artwork>
+--rw yanglib:modules-state [I-D.ietf-netconf-yang-library]
+--rw if:interfaces [RFC7223]
| +--rw bind-network-instance-name="green" string
+--rw network-instances
+--rw network-instance* [name]
+--rw name="green" string
+--rw type? identityref
+--rw enabled=true boolean
+--rw description="The Green VRF" string
+--rw network-instance-policy
| ... (RT=1000:1, RD=1.2.3.4)
+--rw root? schema-mount
+--rw yanglib:modules-state [I-D.ietf-netconf-yang-library]
+--rw if:intefaces [RFC7223]
+--rw mm:network-services
+--rw nn:oam-protocols
+--rw oo:routing
+--rw pp:mpls
</artwork>
</figure>
</t>
<t>
All modules that represent control-plane and data-plane
information may be present at the `root`,
and be accessible via paths modified per
<xref target="I-D.ietf-netmod-schema-mount"/>. The list of available
modules is expected to be implementation dependent. As is the
method used by an implementation to support NIs.
</t>
</section>
<section anchor="sec-NI.3" title=" Network Instance Instantiation">
<t>
TBD -- need to resolve if instantiation is based on new list entry
creation per the pending Schema Mount solution definition.
</t>
</section>
</section>
<section anchor="sec-4" title=" Security Considerations">
<t>
LNE portion is TBD
</t>
<t>
NI portion is TBD
</t>
</section>
<section anchor="sec-5" title=" IANA Considerations">
<t>
This YANG model currently uses a temporary ad-hoc namespace. If it
is placed or redirected for the standards track, an appropriate
namespace URI will be registered in the "IETF XML Registry"
<xref target="RFC3688"/>. The YANG structure modules will be registered in the
"YANG Module Names" registry <xref target="RFC6020"/>.
</t>
<t>
</t>
</section>
<section anchor="sec-6.3" title=" Network Instance Model">
<t>
The structure of the model defined in this document is described
by the YANG module below.
</t>
<t>
<figure>
<artwork><![CDATA[
<CODE BEGINS> file "ietf-network-instance@2016-05-01.yang"
module ietf-network-instance {
yang-version "1";
// namespace
namespace "urn:ietf:params:xml:ns:yang:ietf-network-instance";
prefix "ni";
// import some basic types
import ietf-interfaces {
prefix if;
}
import ietf-ip {
prefix ip;
}
// meta
organization "IETF RTG YANG Design Team Collaboration
with OpenConfig";
contact
"Routing Area YANG Architecture Design Team -
<rtg-dt-yang-arch@ietf.org>";
description
"This module is used to support multiple network instances
within a single physical or virtual device. Network
instances are commonly know as VRFs (virtual routing
and forwarding) and VSIs (virtual switching instances).";
revision "2016-05-01" {
description
"IETF Routing YANG Design Team Meta-Model";
reference "TBD";
}
// extension statements
feature bind-network-instance-name {
description
"Network Instance to which an interface instance is bound";
}
// identity statements
identity network-instance-type {
description
"Base identity from which identities describing
network instance types are derived.";
}
identity ipv4-interface-protocol-type {
description
"Base identity for derivation of IPv4 interface
protocols";
}
identity ipv6-interface-protocol-type {
description
"Base identity for derivation of IPv6 interface
protocols";
}
// typedef statements
// grouping statements
grouping interface-ip-common {
description
"interface-specific configuration for IP interfaces, IPv4 and
IPv6";
}
grouping ipv4-interface-protocols {
container ipv4-interface-protocols {
list ipv4-interface-protocol {
key "type";
leaf type {
type identityref {
base ipv4-interface-protocol-type;
}
mandatory true;
description
"ARP, ICMP, VRRP, DHCP Client, etc.";
}
description
"List of IPv4 protocols configured
on an interface";
}
description
"Container for list of IPv4 protocols configured
on an interface";
}
description
"Grouping for IPv4 protocols configured on an interface";
}
grouping ipv6-interface-protocols {
description
"Grouping for IPv6 protocols configured on
an interface.";
container ipv6-interface-protocols {
description
"Container for list of IPv6 protocols configured
on an interface.";
list ipv6-interface-protocol {
key "type";
description
"List of IPv6 protocols configured
on an interface";
leaf type {
type identityref {
base ipv6-interface-protocol-type;
}
mandatory true;
description
"ND, ICMPv6, VRRP, DHCPv6 Client, etc.";
}
}
}
}
grouping network-instance-policy {
description
"Network instance policies such as route
distinguisher, route targets, VPLS ID and neighbor,
Ethernet ID, etc. ";
reference
"RFC 4364 - BGP/MPLS Virtual Private Networks (VPNs)
RFC 6074 - Provisioning, Auto-Discovery, and Signaling
in Layer 2 Virtual Private Networks (L2VPNs)
RFC 7432 - BGP MPLS-Based Ethernet VPN";
container network-instance-policy {
description "Network Instance Policy -- details TBD";
}
}
// top level device definition statements
container network-instances {
description "Network instances each of which have
an independent IP/IPv6 addressing space
and protocol instantiations. For layer 3,
this consistent with the routing-instance
definition in ietf-routing";
reference "draft-ietf-netmod-routing-cfg";
list network-instance {
key name;
description "List of network-instances";
leaf name {
type string;
description "device scoped
identifier for the network
instance";
}
leaf type {
type identityref {
base network-instance-type;
}
description
"The network instance type -- details TBD
Likely types include core, L3-VRF, VPLS,
L2-cross-connect, L2-VSI, etc.";
}
leaf enabled {
type boolean;
default "true";
description
"Flag indicating whether or not the network
instance is enabled.";
}
leaf description {
type string;
description
"Description of the network instance
and its intended purpose";
}
uses network-instance-policy;
leaf root {
type schema-mount;
description "Root for models supported per
network instance";
}
}
}
// augment statements
augment "/if:interfaces/if:interface" {
description
"Add a node for the identification of the logical network
instance (which is within the interface's identified logical
network element) associated with the IP information
configured on an interface";
leaf bind-network-instance-name {
type string;
description
"Network Instance to which an interface is bound";
}
}
augment "/if:interfaces/if:interface/ip:ipv4" {
description
"Add a node for the identification of the logical
network instance (which is within the interface's
identified physical or virtual device) associated with
the IP information configured on an interface";
leaf bind-network-instance-name {
type string;
description
"Network Instance to which IPv4 interface is bound";
}
}
augment "/if:interfaces/if:interface/ip:ipv6" {
description
"Add a node for the identification of the logical
network instance (which is within the interface's
identified physical or virtual device) associated with
the IP information configured on an interface";
leaf bind-network-instance-name {
type string;
description
"Network Instance to which IPv6 interface is bound";
}
}
// rpc statements
// notification statements
}
<CODE ENDS>
]]></artwork>
</figure>
</t>
</section>
</middle>
<?rfc needLines="20"?>
<back>
<references title="Normative References">
<reference anchor="RTG-DEVICE-MODEL">
<front>
<title>Network Device YANG Organizational Models</title>
<author initials='A.' surname="Lindem" fullname='Acee Lindem' role='editor'>
<organization>Cisco Systems</organization>
</author>
<author initials='L.' surname="Berger" fullname='Lou Berger' role='editor'>
<organization>LabN Consulting, L.L.C.</organization>
</author>
<author initials='D.' surname="Bogdanovic" fullname='Dean Bogdanovic'>
<organization></organization>
</author>
<author initials='C.' surname="Hopps" fullname='Christan Hopps'>
<organization>Deutsche Telekom</organization>
</author>
<date month="May" year="2016" />
</front>
<seriesInfo name="Internet-Draft" value="draft-rtgyangdt-rtgwg-device-model-04.txt"/>
</reference>
<reference anchor="LNE-MODEL">
<front>
<title>Logical Network Element Model</title>
<author initials='L.' surname="Berger" fullname='Lou Berger'>
<organization>LabN Consulting, L.L.C.</organization>
</author>
<author initials='C.' surname="Hopps" fullname='Christan Hopps'>
<organization>Deutsche Telekom</organization>
</author>
<author initials='A.' surname="Lindem" fullname='Acee Lindem'>
<organization>Cisco Systems</organization>
</author>
<author initials='D.' surname="Bogdanovic" fullname='Dean Bogdanovic'>
<organization></organization>
</author>
<date month="May" year="2016" />
</front>
<seriesInfo name="Internet-Draft" value="draft-rtgyangdt-rtgwg-lne-model-00.txt"/>
</reference>
<?rfc include="reference.I-D.draft-ietf-netmod-schema-mount-01.xml"?>
<?rfc include="reference.RFC.6020"?>
<?rfc include="reference.RFC.7223"?>
<?rfc include="reference.RFC.7277"?>
<?rfc include="reference.RFC.3688"?>
<?rfc include="reference.RFC.4026"?>
</references>
<references title="Informative References">
<?rfc include="reference.I-D.draft-openconfig-netmod-opstate-01.xml"?>
<?rfc include="reference.I-D.draft-ietf-netmod-routing-cfg-20.xml"?>
<?rfc include="reference.I-D.draft-ietf-netmod-opstate-reqs-03.xml"?>
<?rfc include="reference.I-D.draft-ietf-netconf-yang-library-05.xml"?>
</references>
<?rfc needLines="100"?>
<section title="Acknowledgments">
<t>The Routing Area Yang Architecture design team members included Acee
Lindem, Anees Shaikh, Christian Hopps, Dean Bogdanovic, Lou Berger,
Qin Wu, Rob Shakir, Stephane Litkowski, and Yan Gang.</t>
<t>The RFC text was produced using Marshall Rose's xml2rfc tool.
<vspace blankLines="100"/></t>
</section>
<section title="Contributors">
<figure>
<artwork>
Contributors' Addresses
TBD
</artwork>
</figure>
</section>
</back>
</rfc>
<!-- Local Variables: -->
<!-- fill-column:72 -->
<!-- End: -->
| PAFTECH AB 2003-2026 | 2026-04-22 17:53:40 |