One document matched: draft-litkowski-idr-bgp-timestamp-00.txt
Interdomain Working Group S. Litkowski
Internet-Draft Orange Business Service
Intended status: Standards Track K. Patel
Expires: January 4, 2015 Cisco Systems
J. Haas
Juniper Networks
July 3, 2014
Timestamp support for BGP paths
draft-litkowski-idr-bgp-timestamp-00
Abstract
BGP is more and more used to transport routing information for
critical services. Some BGP updates may be critical to be received
as fast as possible : for example, in a layer 3 VPN scenario where a
dual-attached site is loosing primary connection, the BGP withdraw
message should be propagated as fast as possible to restore the
service. The same criticity exists for other address-families like
multicast VPNs where "join" messages should also be propagated very
fast.
Experience of service providers shows that BGP path propagation time
may vary depending on network conditions (especially load of BGP
speaker on the path) and too long propagation time are affecting
customer service.
It is important for service providers to keep track of BGP updates
propagation time to monitor quality of service for the customers. It
is also important to be able to identify BGP Speakers that are
slowing down the propagation.
This document presents a solution to transport timestamps of a BGP
path.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Litkowski, et al. Expires January 4, 2015 [Page 1]
Internet-Draft bgp-timestamp July 2014
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on January 4, 2015.
Copyright Notice
Copyright (c) 2014 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Problem statement . . . . . . . . . . . . . . . . . . . . . . 3
2. Proposal . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. BGP timestamp attribute . . . . . . . . . . . . . . . . . . . 4
4. Processing the BGP timestamp attribute . . . . . . . . . . . 6
4.1. Inspection list . . . . . . . . . . . . . . . . . . . . . 6
4.2. Originating a timestamped route in BGP . . . . . . . . . 6
4.3. Receiving a timestamped route in BGP . . . . . . . . . . 6
4.4. Sending a timestamped route in BGP . . . . . . . . . . . 7
4.5. Inter-AS considerations . . . . . . . . . . . . . . . . . 7
4.5.1. Drop option . . . . . . . . . . . . . . . . . . . . . 8
4.5.2. Summary option . . . . . . . . . . . . . . . . . . . 9
4.5.3. Propagate option . . . . . . . . . . . . . . . . . . 9
4.6. Handling malformed attribute . . . . . . . . . . . . . . 10
5. Monitoring BGP Update propagation time . . . . . . . . . . . 10
5.1. An architecture to measure BGP Update propagation time . 10
5.2. Measurement accuracy . . . . . . . . . . . . . . . . . . 11
5.3. Dealing with stale information . . . . . . . . . . . . . 12
6. Compared to BMP . . . . . . . . . . . . . . . . . . . . . . . 13
7. Deployment considerations . . . . . . . . . . . . . . . . . . 14
Litkowski, et al. Expires January 4, 2015 [Page 2]
Internet-Draft bgp-timestamp July 2014
8. Security considerations . . . . . . . . . . . . . . . . . . . 14
9. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 15
10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 15
11. Normative References . . . . . . . . . . . . . . . . . . . . 15
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 15
1. Problem statement
CE3----PE3 PE4 --- CE4 (Source)
\ /
RR3 RR4
\ /
RR5
/ \
RR1 RR2
/ | \
/ | \
CE1----PE1 PE5 PE2 --- CE2
|
CE5
Figure 1
The figure 1 describes a typical hierarchical RR design where PEs are
meshed to local RRs and local RRs are meshed to more centric RRs. We
consider a single multicast VPN between all CEs. CE4 is the source,
all others may be receivers. The BGP controlplane also supports some
other BGP service like L3VPN service.
We consider an event in L3VPN service leading to RR1 being temporarly
overloaded (for example, RR1 is processing massive updates due to a
router failure or formatting updates for a route-refresh). In the
same timeframe, CE1 wants to join the multicast flow from CE4. PE1
propagates the C-multicast route to RR1, but RR1 fails to propagate
the route to RR5 because it is busy processing L3VPN. When RR1
finishes the L3VPN job, it would send the C-multicast route to RR5
and updates would be imported by PE4. The long time to join the flow
may cause CE4 to miss part of the multicast flow.
All BGP implementations are different in term of internal processing
within an address family or between address family. The issue
described above is just given as an example, and the document does
not presume that all implementations are suffering from this exact
issue. But whatever the implementation, their always be cases where
BGP update processing could be delayed.
Litkowski, et al. Expires January 4, 2015 [Page 3]
Internet-Draft bgp-timestamp July 2014
Service providers currently lack of performant solution to keep track
of BGP update propagation time as well as solution to identify the
BGP speakers causing issues.
BMP (BGP Monitoring Protocol) may be a solution but as several
drawbacks (see Section 6).
2. Proposal
Our proposal is based on the path vector property of BGP. Each hop
within the path would add a tuple (ID,timestamp) information in the
BGP path. An ordered list of timestamps would so be built along the
path.
BGP Update BGP Update BGP Update BGP Update
10.0.0.0/8 10.0.0.0/8 10.0.0.0/8 10.0.0.0/8
Timestamp: Timestamp: Timestamp: Timestamp:
R1:T1 R1:T1 R1:T1 R1:T1
R2:T2 R2:T2 R2:T2
R3:T3 R3:T3
R4:T4
R1 ------------> R2 ------------> R3 ------------> R4 ------------> R5
Using this mechanism, we can easily identify if a hop within a path
is slowing down the propagation.
We propose to use a new BGP attribute, BGP timestamp attribute to
encode timestamps information.
3. BGP timestamp attribute
The BGP timestamp (BGP-TS) Attribute is an optional transitive BGP
Path Attribute. The attribute type code is TBD.
The value field of the BGP timestamp attribute is defined here :
Litkowski, et al. Expires January 4, 2015 [Page 4]
Internet-Draft bgp-timestamp July 2014
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OType | Originator (variable) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Timestamp #1 (variable) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Timestamp #2 (variable) |
...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Timestamp #n (variable) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
o OType : A single octet encoding the originator type
* Type 1 : 2 bytes ASN.
* Type 2 : 4 bytes ASN.
* Type 3 : IPv4 address.
* Type 4 : IPv6 address.
o Originator : IP address or AS number identifying the first router
or AS that added the BGP timestamp attribute.
o Timestamp : ordered list of timestamps, the first timestamp is the
first router information. The timestamps are encoded as follows :
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Receive Timestamp #x |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|A|P|S|T| Rsvd | SyncType | AS#x (variable) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Peer#x (variable) |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
* Receive timestamp : the time at which the BGP path was
received. When originating a path in BGP, the timestamp is the
originating time. The format of the timestamp is the same as
in [RFC5905] and is as follows: the first 32 bits represent the
unsigned integer number of seconds elapsed since 0h on 1
Litkowski, et al. Expires January 4, 2015 [Page 5]
Internet-Draft bgp-timestamp July 2014
January 1900; the next 32 bits represent the fractional part of
a second that has elapsed since then.
* Flags :
+ A : AS type, if unset the AS field is a 2 bytes ASN,
otherwise the AS field is a 4 bytes ASN.
+ P : Peer type, if unset the peer field is an IPv4 address,
otherwise the peer field is an IPv6 address.
+ S : Summary, if set, the timestamp is a summary entry and
does not contain a peer field. If set, the P bit MUST be
set to zero.
+ T : Synchronized, if set, the BGP speaker clock is
synchronized to an external system.
* SyncType : defines the stratum as defined in [RFC5905].
* AS : the local AS of the BGP Speaker.
* Peer : the routerID of the BGP Speaker.
4. Processing the BGP timestamp attribute
4.1. Inspection list
A BGP Speaker supporting the BGP-TS can decide to timestamp only some
specific BGP paths. An inspection list may be configured by the user
(filter) to apply timestamping on a specific set of BGP prefixes or
paths. By default, we suggest that a BGP Speaker supporting BGP-TS
SHOULD NOT timestamp any BGP paths.
4.2. Originating a timestamped route in BGP
When a BGP Speaker supporting BGP-TS originates a new path in BGP
that matches the inspection list, it MUST add the BGP-TS attribute to
the BGP path and MUST set the receive timestamp field to the time the
path was originated in BGP. If the BGP Speaker is synchronized to an
external system when originating the route, the S-bit MUST be set in
the attribute and the SyncType MUST be set to the current stratum.
4.3. Receiving a timestamped route in BGP
When a BGP Speaker supporting BGP-TS receives a BGP path that matches
the inspection list and does not contains a BGP-TS attribute, it MUST
add a BGP-TS attribute containing :
Litkowski, et al. Expires January 4, 2015 [Page 6]
Internet-Draft bgp-timestamp July 2014
o The originator type and originator field are set according to
local BGP Speaker informations.
o The timestamp entry contains information related to the local BGP
Speaker.
o If the BGP Speaker is synchronized to an external system when
receiving the route, the S-bit MUST be set in the attribute and
the SyncType MUST be set to the current stratum.
When a BGP Speaker supporting BGP-TS receives a BGP path that matches
the inspection list and contains a BGP-TS attribute, it MUST append
its own timestamp entry in the existing attribute. If the BGP
Speaker is synchronized to an external system when receiving the
route, the S-bit MUST be set in the attribute and the SyncType MUST
be set to the current stratum.
When a BGP Speaker supporting BGP-TS receives a BGP path that does
not the inspection list and contains a BGP-TS attribute, it MUST NOT
change the existing attribute.
When a BGP Speaker not supporting BGP-TS receives a BGP path that
contains a BGP-TS attribute, it MUST follow the standard BGP
procedures described in [RFC4271].
4.4. Sending a timestamped route in BGP
For a manageability/security purpose, the authors suggest that BGP
timestamp attribute MAY NOT be sent to a peer unless it was
explicitly configured for. This would prevent timestamp and internal
address informations to be propagated to some external peers for
example. See Section 4.5 for more information.
If a BGP path containing a BGP-TS attribute must be sent to be peer
not configured with BGP timestamp option, the BGP-TS attribute should
be dropped when the update message is sent to the peer.
4.5. Inter-AS considerations
Litkowski, et al. Expires January 4, 2015 [Page 7]
Internet-Draft bgp-timestamp July 2014
BGP update CE2 add timestamp
10.0.0.0/8 when receiving path
TS:
CE1:T1
CE1--------->R1 ------------> R2 ------------> R3 ------------> R4 ------------> CE2
| | | |
| | | |
AS1 AS2
Figure 2
In the figure above, we consider that customer wants to monitor BGP
updates propagation time between its two sites.
If AS1 and AS2 BGP Speakers does not support BGP-TS, the attribute
will be transported transparently accross AS1 without any processing.
CE2 will so receive the BGP path with only a single timestamp entry
from CE1.
If AS1 and AS2 BGP Speakers does support BGP-TS, three different
options are offered : drop, summarize, propagate.
4.5.1. Drop option
If AS1 and/or AS2 BGP Speakers support BGP-TS, they may not want to
expose their timestamps or internal BGP topology to other ASes. If a
service does not want to propagate timestamp information to external
peers, it can decide to not activate the "timestamp" option on the
peer configuration , as explained in Section 4.4.
BGP update BGP update BGP update BGP update BGP update
10.0.0.0/8 10.0.0.0/8 10.0.0.0/8 10.0.0.0/8 10.0.0.0/8
TS: TS:
CE1:T1 CE1:T1
CE1--------->R1 ------------> R2 ------------> R3 ------------> R4 ------------> CE2
| | no TS | |
| | | |
AS1 AS2
Figure 3
Litkowski, et al. Expires January 4, 2015 [Page 8]
Internet-Draft bgp-timestamp July 2014
4.5.2. Summary option
If AS1 and/or AS2 BGP Speakers support BGP-TS, they may want to offer
timestamp service to their customers but they want to hide their
internal topology. In order to achieve the expected behavior, AS1/
AS2 can activate a timestamp summary option on the external peer.
BGP update BGP update BGP update BGP update BGP update
10.0.0.0/8 10.0.0.0/8 10.0.0.0/8 10.0.0.0/8 10.0.0.0/8
TS: TS: TS: TS: TS:
CE1:T1 CE1:T1 CE1:T1 CE1:T1 CE1:T1
R1:T2 AS1:T3 AS1:T3 AS1:T3
R3:T4 AS2:T5
CE1--------->R1 ------------> R2 ------------> R3 ------------> R4 ------------> CE2
| | TS summary | | TS summary
| | | |
AS1 AS2
Figure 4
When using summary option, the BGP-TS attribute is modified as
follows when exporting the route :
o All timestamp entries containing the local AS in AS field are
removed.
o A new timestamp entry is created and inserted in place of removed
entries (n entries replaced by 1).
o The new timestamp entry MUST have the S bit set.
o The new timestamp entry MUST NOT have a peer field.
o The timestamp of the new timestamp entry is the receiving
timestamp of the last timestamp entry that has been removed.
4.5.3. Propagate option
If AS1 and/or AS2 BGP Speakers support BGP-TS, they may want to offer
timestamp service to their customers with a full view. The behavior
is the default intraAS behavior.
Litkowski, et al. Expires January 4, 2015 [Page 9]
Internet-Draft bgp-timestamp July 2014
BGP update BGP update BGP update BGP update BGP update
10.0.0.0/8 10.0.0.0/8 10.0.0.0/8 10.0.0.0/8 10.0.0.0/8
TS: TS: TS: TS: TS:
CE1:T1 CE1:T1 CE1:T1 CE1:T1 CE1:T1
R1:T2 R1:T2 R1:T2 R1:T2
R2:T3 R2:T3 R2:T3
R3:T4 R3:T4
R4:T5
CE1--------->R1 ------------> R2 ------------> R3 ------------> R4 ------------> CE2
| | | |
| | | |
AS1 AS2
Figure 5
4.6. Handling malformed attribute
When receiving a BGP Update message containing a malformed BGP-TS
attribute, an "attribute-discard" action MUST be applied as defined
in .
5. Monitoring BGP Update propagation time
5.1. An architecture to measure BGP Update propagation time
--------- -------
/ \ / \
RTR_SRC ----- | AS1 | ----- | AS2 | ---- RTR_DST1
\ / \ /
--------- ---------
| |
| |
--------- -------
/ \ / \
RTR_DST2 ---- | AS4 | | AS3 | ---- RTR_DST3
\ / \ /
--------- ---------
Figure 6
Litkowski, et al. Expires January 4, 2015 [Page 10]
Internet-Draft bgp-timestamp July 2014
Single AS
-------------------------------------------
/ \
| RR1 ---------- RR2 |
| / \ \ |
| RTR_SRC1 \ RTR_DST1 |
| \ |
| RR3 |
| | |
| RTR_DST2 |
| |
\ /
-------------------------------------------
Figure 7
Figure 6 and Figure 7 describes an interAS and a single AS scenario
where a service provider wants to monitor BGP Update propagation time
from a router to multiple routers. In Figure 6, multiple probing
routers are attached to multiple ASes. In Figure 7, all probing
routers are in the same AS.
An external tool should command RTR_SRC to originate a probing BGP
path. Each probing router is configured to match the path in its
inspection list. The BGP path would propagate across ASes whatever
they are supporting BGP TS or not. Each probing router would receive
the BGP path and add timestamp information. Authors suggest to
implementors to use a local wrapping buffer on each node and record
entries in the buffer each time a BGP path is timestamped. An
external tool should then retrieve timestamps information from
RTR_DSTx. How the information is retrieved is out of scope of the
document but we can imagine using :
o BMP from the external tool to each RTR_DSTx.
o NetConf call to retrieve wrapping buffer information.
o SNMP call to retrieve wrapping buffer information.
o CLI command to retrieve wrapping buffer information.
5.2. Measurement accuracy
For the solution to be accurate, it is mandatory for BGP Speaker to
be synchronized. This could be achieved easily within a single AS
but in a inter domain scenario, it is hard to ensure that all
Speakers are synchronized to a good clock source.
Litkowski, et al. Expires January 4, 2015 [Page 11]
Internet-Draft bgp-timestamp July 2014
The S bit and SyncType fields are set to help operators to understand
the accuracy of the timestamp measurements and being able to compare
timestamps between them.
5.3. Dealing with stale information
Single AS
-------------------------------------------
/ RTR_SRC2- 10/8 \
| / |
| RR1 ---------- RR2 |
| / \ \ |
| RTR_SRC1 \ RTR_DST1 |
| | \ |
| 10/8 RR3 |
| | |
| RTR_DST2 |
| |
\ /
-------------------------------------------
Figure 8
In the figure above, consider that the service provider is keep
tracking of propagation time for real NLRIs (corresponding to
customer routes). All the BGP Speakers in our figure are configured
to inspect the NLRI 10/8 which is multihomed. We consider that the
network is starting and the NLRI has not been propagated yet.
RTR_SRC1 starts to propagate 10/8 within the BGP controlplane. All
BGP Speakers considers the path as best and this path will be
propagated within the whole controlplane. Each BGP Speaker would add
its timestamp information and RTR_DST1 and RTR_DST2 would be able to
record the timestamp vector. In this case, the timestamp vector is
quite accurate because it represents an end to end propagation.
Now RTR_SRC2 starts to propagate its own path. RR2 has two paths for
10/8 and will choose the best one, let's consider that RTR_SRC2 path
is the best one, RTR_SRC2 path will so be propagated and timestamp
vector will be updated. RR1 will also have two paths, and we
consider that RR1 prefers RTR_SRC1 path, so RTR_SRC2 path will not be
propagated by RR1. In this situation, RTR_DST1 will receive the path
from RR2 with accurate timestamp (end to end propagation) but
RTR_DST2 will never receive it.
We could also consider a stable network situation, where both paths
have been advertised for a long time. A network event may occur
(e.g. IGP metric change) that would cause a BGP Speaker within a
path vector to change its best path. In Figure 8, an IGP event, may
Litkowski, et al. Expires January 4, 2015 [Page 12]
Internet-Draft bgp-timestamp July 2014
cause RR1 to change its decision and prefers the path originated by
RTR_SRC2 as best, the path will be propagated with previous received
timestamp information that are no more accurate. RTR_DST2 will
receive a BGP timestamp vector containing stale timestamp
informations as well as new ones.
The case of sending stale timestamp information can also appear with
a single originator as soon as some redundancy in the BGP design is
involved (multiple RRs, multiple ASBRs ...).
An external tool that monitors BGP timestamp should take care about
analysing only end to end propagation scenarios.
6. Compared to BMP
BMP (BGP Monitoring Protocol) [I-D.ietf-grow-bmp] is a solution to
monitor BGP sessions and provides a convenient interface for
obtaining route views. BMP is a complete suite of messages to
exchange informations regarding a BGP session.
We can imagine to use BMP as a solution to monitor BGP update
propagation time but there is multiple drawbacks associated with such
solution :
o BMP provides dump of all received BGP update (per peer). If we
are interested only in probing BGP routes, a strong filtering of
information may be needed in BMP messages.
o BMP does not mandate timestamping of messages (as per
[I-D.ietf-grow-bmp] Section 5) : "If the implementation is able to
provide information about when routes were received, it MAY
provide such information in the BMP timestamp field. Otherwise,
the BMP timestamp field MUST be set to zero, indicating that time
is not available."
o BMP may provide (if implementation available) timestamps
information only for a single router point of view. If we want to
retrieve timestamps of all BGP Speakers on a path, a BMP session
is required to all BGP speakers. Correlation (based on known
design) is also required at the external tool to order timestamps
from each BMP session.
o If BMP provides timestamp information, it does not provide
information on how the router clock is synchronized (free run,
NTP, GPS ...).
Using BMP to monitor BGP update propagation may complexify the design
of the monitor solution.
Litkowski, et al. Expires January 4, 2015 [Page 13]
Internet-Draft bgp-timestamp July 2014
7. Deployment considerations
This solution is not intended to perform timestamp imposition on all
BGP updates.
Service provider implementing the BGP timestamp attribute must be
aware of the propagation rules of the NLRIs to be inspected. If we
consider an implementation scenario, where a path for NLRI is already
propagated, a new path may appear and starts to be propagated,
propagation of this new path may stop at a certain point because a
BGP Speaker may consider the old path as the best one. Another
scenario, could be that the two paths are installed, and for a BGP
Speaker within the path vector, the best path is changing because of
an IGP metric change, this BGP Speaker will send a new BGP update and
timestamp information of the path will be updated but will have no
more sense : origin timestamp will be quite old, but timestamps
recorded after this BGP Speaker will be recent. This kind of
scenario is complex to understand.
The deployment scenario we are targeting is really to inspect some
specific NLRIs identified by the service provider where the
propagation rules are well known (see Section 5 as an example).
Service provider may rely on existing NLRIs (real routes), or
ephemeral NLRIs (dedicated NLRIs for beaconing). Whatever the NLRI
used, the tool used by the service provider to collect and interpret
the timestamp must be aware of the propagation rules and must record
events only if propagation is end to end (from originator to
listener).
The inspection list should be kept as small as possible in order to
not introduce processing overhead and as a consequence slow down
propagation. Implementors should take care about reducing as much as
possible the processing overhead introduced by the inspection list
and timestamp imposition.
8. Security considerations
Depending of the implementation and router capacity, adding
timestamps to BGP path may consume some router ressources. As
proposed in Section 4.1, by default a BGP Speaker will not timestamp
any path and inspection list should be configured to activate
timestamping on a subset of paths. Using this approach, we consider
that overhead that may be introduced by timestamping BGP paths is
well controlled by operators. An external router cannot force an
internal router to timestamp.
Providing detailled timestamps information to other ASes may
introduce security issues by exposing internal datas (part of BGP
Litkowski, et al. Expires January 4, 2015 [Page 14]
Internet-Draft bgp-timestamp July 2014
topology, IP addresses, internal performance) to external entities.
The proposal we make in Section 4.5 solves this security issue by
giving flexibility to operators on the level of information he wants
to expose to external peers.
9. Acknowledgements
10. IANA Considerations
IANA shall assign a codepoint for the BGP Timestamp attribute. This
codepoint will come from the "BGP Path Attributes" registry.
11. Normative References
[I-D.ietf-grow-bmp]
Scudder, J., Fernando, R., and S. Stuart, "BGP Monitoring
Protocol", draft-ietf-grow-bmp-07 (work in progress),
October 2012.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC4271] Rekhter, Y., Li, T., and S. Hares, "A Border Gateway
Protocol 4 (BGP-4)", RFC 4271, January 2006.
[RFC5905] Mills, D., Martin, J., Burbank, J., and W. Kasch, "Network
Time Protocol Version 4: Protocol and Algorithms
Specification", RFC 5905, June 2010.
Authors' Addresses
Stephane Litkowski
Orange Business Service
Email: stephane.litkowski@orange.com
Keyur Patel
Cisco Systems
Email: keyupate@cisco.com
Jeff Haas
Juniper Networks
Email: jhaas@juniper.net
Litkowski, et al. Expires January 4, 2015 [Page 15]
| PAFTECH AB 2003-2026 | 2026-04-24 01:42:40 |