One document matched: draft-ietf-tsvwg-rsvp-proxy-approaches-02.txt
Differences from draft-ietf-tsvwg-rsvp-proxy-approaches-01.txt
TSVWG F. Le Faucheur
Internet-Draft Cisco
Intended status: Informational J. Manner
Expires: March 15, 2008 University of Helsinki
D. Wing
Cisco
A. Guillou
Neuf
September 12, 2007
RSVP Proxy Approaches
draft-ietf-tsvwg-rsvp-proxy-approaches-02.txt
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on March 15, 2008.
Copyright Notice
Copyright (C) The IETF Trust (2007).
Abstract
RSVP signaling can be used to make end-to-end resource reservations
in an IP network in order to guarantee the Quality of Service
required by certain flows. With conventional RSVP, both the data
Le Faucheur, et al. Expires March 15, 2008 [Page 1]
Internet-Draft RSVP Proxy Approaches September 2007
sender and receiver of a given flow take part in RSVP signaling.
Yet, there are many use cases where resource reservation is required,
but the receiver, the sender, or both, is not RSVP-capable. This
document presents RSVP Proxy behaviors allowing RSVP routers to
perform RSVP signaling on behalf of a receiver or a sender that is
not RSVP-capable. This allows resource reservations to be
established on critical parts of the end-to-end path. This document
reviews conceptual approaches for deploying RSVP Proxies and
discusses how RSVP reservations can be synchronized with application
requirements, despite the sender, receiver, or both not participating
in RSVP. This document also points out where extensions to RSVP (or
to other protocols) may be needed for deployment of a given RSVP
Proxy approach. However, such extensions are outside the scope of
this document. Finally, practical use cases for RSVP Proxy are
described.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. RSVP Proxy Behaviors . . . . . . . . . . . . . . . . . . . . . 5
2.1. RSVP Receiver Proxy . . . . . . . . . . . . . . . . . . . 5
2.2. RSVP Sender Proxy . . . . . . . . . . . . . . . . . . . . 6
3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 7
4. RSVP Proxy Approaches . . . . . . . . . . . . . . . . . . . . 8
4.1. Path-Triggered Receiver Proxy . . . . . . . . . . . . . . 8
4.2. Path-Triggered Sender Proxy for Reverse Direction . . . . 10
4.3. Inspection-Triggered Proxy . . . . . . . . . . . . . . . . 13
4.4. STUN-Triggered Proxy . . . . . . . . . . . . . . . . . . . 15
4.5. Application_Entity-Controlled Proxy . . . . . . . . . . . 17
4.5.1. Application_Entity-Controlled Sender Proxy using
"RSVP over GRE" . . . . . . . . . . . . . . . . . . . 19
4.5.2. Application_Entity-Controlled Proxy via Co-Location . 21
4.6. Policy_Server-Controlled Proxy . . . . . . . . . . . . . . 22
4.7. RSVP-Signaling-Triggered Proxy . . . . . . . . . . . . . . 25
4.8. Endsystem-Controlled Proxy . . . . . . . . . . . . . . . . 26
4.9. Reachability Considerations . . . . . . . . . . . . . . . 26
5. Security Considerations . . . . . . . . . . . . . . . . . . . 27
6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 28
7. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 28
8. Informative References . . . . . . . . . . . . . . . . . . . . 28
Appendix A. Use Cases for RSVP Proxies . . . . . . . . . . . . . 30
A.1. RSVP-based VoD CAC in Broadband Aggregation Networks . . . 30
A.2. RSVP-based Voice/Video CAC in Enterprise WAN . . . . . . . 34
A.3. RSVP-based Voice CAC in Telephony Service Provider Core . 35
A.4. RSVP Proxies for Mobile Access Networks . . . . . . . . . 37
A.5. RSVP Proxies for Reservations in the presence of IPsec
Gateways . . . . . . . . . . . . . . . . . . . . . . . . . 39
Le Faucheur, et al. Expires March 15, 2008 [Page 2]
Internet-Draft RSVP Proxy Approaches September 2007
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 42
Intellectual Property and Copyright Statements . . . . . . . . . . 44
Le Faucheur, et al. Expires March 15, 2008 [Page 3]
Internet-Draft RSVP Proxy Approaches September 2007
1. Introduction
Guaranteed Quality of Service (QoS) for some applications with tight
requirements (such as voice or video) may be achieved by reserving
resources in each node on the end-to-end path. The main IETF
protocol for these resource reservations is RSVP, specified in
[RFC2205]. RSVP does not require that all intermediate nodes support
RSVP, however it assumes that both the sender and the receiver of the
data flow support RSVP. There are environments where it would be
useful to be able to reserve resources for a flow on at least a
subset of the flow path even when the sender or the receiver (or
both) is not RSVP capable.
Since the data sender or receiver may be unaware of RSVP, there are
two scenarios. In the first case, an entity in the network must
operate on behalf of the data sender, and in particular, generate
RSVP Path messages, and eventually receive, process and sink Resv
messages. We refer to this entity as the RSVP Sender Proxy. In the
latter case, an entity in the network must receive Path messages sent
by a data sender (or by an RSVP Sender Proxy), sink those, and return
Resv messages on behalf of the data receiver(s). We refer to this
entity as the RSVP Receiver Proxy.
The flow sender and receiver generally have at least some (if not
full) awareness of the application producing or consuming that flow.
Hence, the sender and receiver are in a natural position to
synchronize the establishment, maintenance and tear down of the RSVP
reservation with the application requirements. Similarly they are in
a natural position to determine the characteristics of the
reservation (bandwidth, QoS service,...) which best match the
application requirements. For example, before completing the
establishment of a multimedia session, the endpoints may decide to
establish RSVP reservations for the corresponding flows. Similarly,
when the multimedia session is torn down, the endpoints may decide to
tear down the corresponding RSVP reservations. For instance,
[RFC3312] discusses how RSVP reservations can be very tightly
synchronized by SIP endpoints with SIP session control and SIP
signaling.
When RSVP reservation establishment, maintenance and tearing down is
to be handled by RSVP Proxies on behalf of an RSVP sender or
receiver, a key challenge for the RSVP Proxy is to determine when the
RSVP reservations need to be established, maintained and torn down
and to determine what are the characteristics (bandwidth, QoS
Service,...) of the required RSVP reservations matching the
application requirements. We refer to this problem as the
synchronization of RSVP reservations with application level
requirements.
Le Faucheur, et al. Expires March 15, 2008 [Page 4]
Internet-Draft RSVP Proxy Approaches September 2007
The IETF Next Steps in Signaling (NSIS) working group is designing,
as one their charter items, a new QoS signaling protocol. This
scheme already includes the notion of proxy operation, and
terminating QoS signaling on nodes that are not the actual data
senders or receivers. This is the same concept as the proxy
operation for RSVP discussed in this document. One difference though
is that the NSIS framework does not consider multicast resource
reservations, which RSVP provides today.
The next section introduces the notion of RSVP Sender Proxy and RSVP
Receiver Proxy. The following section defines useful terminology.
The subsequent section then presents several fundamental RSVP Proxy
approaches insisting on how they achieve the necessary
synchronization of RSVP reservations with application level
requirements. Appendix A includes more detailed use cases for the
proxies in various real life deployment environments.
2. RSVP Proxy Behaviors
This section discusses the two types of proxies; the RSVP Sender
Proxy operating on behalf of data senders, and the RSVP Receiver
Proxy operating for data receivers. The concepts presented in this
document are not meant to replace the standard RSVP and end-to-end
RSVP reservations are still expected to be used whenever possible.
However, RSVP Proxies are intended to facilitate RSVP deployment
where end-to-end RSVP signaling is not possible.
2.1. RSVP Receiver Proxy
With conventional RSVP operations, RSVP reservations are controlled
by receivers of data. After a data sender has sent an RSVP Path
message towards the intended recipient(s), each recipient that
requires a reservation generates a Resv message. If, however, a data
receiver is not running the RSVP protocol, the last hop RSVP router
will still send the Path message to the data receiver, which will
silently drop this message as an IP packet with an unknown protocol
number.
In order for reservations to be made in such a scenario, one of the
RSVP routers on the data path must somehow know that the data
receiver will not be participating in the resource reservation
signaling. This RSVP router should, thus, perform RSVP Receiver
Proxy functionality on behalf of the data receiver. This is
illustrated in Figure 1. Various mechanisms by which the RSVP proxy
router can gain the required information are discussed later in the
document.
Le Faucheur, et al. Expires March 15, 2008 [Page 5]
Internet-Draft RSVP Proxy Approaches September 2007
|----| *** *** |----------| |----|
| S |---------*r*----------*r*---------| RSVP |----------| R |
|----| *** *** | Receiver | |----|
| Proxy |
|----------|
===================RSVP==============>
***********************************************************>
|----| RSVP-capable |----| non-RSVP-capable ***
| S | Sender | R | Receiver *r* regular RSVP
|----| |----| *** router
***> unidirectional media flow
==> segment of flow path protected by RSVP reservation
Figure 1: RSVP Receiver Proxy
2.2. RSVP Sender Proxy
With conventional RSVP operations, if a data sender is not running
the RSVP protocol, a resource reservation can not be set up; a data
receiver can not alone reserve resources without Path messages first
being received. Thus, even if the data receiver is running RSVP, it
still needs some node on the data path to send a Path message towards
the data receiver.
In that case, an RSVP node on the data path must somehow know that it
should generate Path messages to allow the receiver to set up the
resource reservation. This node is referred to as the RSVP Sender
Proxy and is illustrated in Figure 2. This case is more complex than
the Receiver Proxy case, since the RSVP Sender Proxy must be able to
generate all the information in the Path message (such as the Sender
TSpec) without the benefit of having previously received any RSVP
message. An RSVP Receiver Proxy, by contrast only needs to formulate
an appropriate Resv message in response to an incoming Path message.
Mechanisms to operate an RSVP Sender Proxy are discussed later in
this document.
Le Faucheur, et al. Expires March 15, 2008 [Page 6]
Internet-Draft RSVP Proxy Approaches September 2007
|----| |----------| *** *** |----|
| S |---------| RSVP |---------*r*----------*r*----------| R |
|----| | Sender | *** *** |----|
| Proxy |
|----------|
================RSVP==================>
***********************************************************>
|----| non-RSVP-capable |----| RSVP-capable ***
| S | Sender | R | Receiver *r* regular RSVP
|----| |----| *** router
***> unidirectional media flow
==> segment of flow path protected by RSVP reservation
Figure 2: RSVP Sender Proxy
3. Terminology
On-Path: located on the datapath of the actual flow of application
data (regardless of where it is located with respect to the
application level signaling path).
Off-Path: not On-Path.
RSVP-capable (or RSVP-aware): which supports the RSVP protocol as per
[RFC2205].
RSVP Receiver Proxy: an RSVP capable router performing, on behalf of
a receiver, the RSVP operations which would normally be performed by
an RSVP-capable receiver if end-to-end RSVP signaling was used. Note
that while RSVP is used upstream of the RSVP Receiver Proxy, RSVP is
not used downstream of the RSVP Receiver Proxy.
RSVP Sender Proxy: an RSVP capable router performing, on behalf of a
sender, the RSVP operations which would normally be performed by an
RSVP-capable sender if end-to-end RSVP signaling was used. Note that
while RSVP is used downstream of the RSVP Sender Proxy, RSVP is not
used upstream of the RSVP Sender Proxy.
Regular RSVP Router: an RSVP-capable router which is not behaving as
a RSVP Receiver Proxy nor as a RSVP Sender Proxy.
Le Faucheur, et al. Expires March 15, 2008 [Page 7]
Internet-Draft RSVP Proxy Approaches September 2007
Note that the roles of RSVP Receiver Proxy, RSVP Sender Proxy,
Regular RSVP Router are all relative to one unidirectional flow. A
given router may act as the RSVP Receiver Proxy for a flow, as the
RSVP Sender Proxy for another flow and as a Regular RSVP router for
yet another flow.
Application level signaling: signaling between entities operating
above the IP layer and which are aware of the QoS requirements for
actual media flows. SIP and RTSP are examples of application level
signaling protocol. RSVP is clearly not an application level
signaling.
4. RSVP Proxy Approaches
This section discusses fundamental RSVP Proxy approaches.
4.1. Path-Triggered Receiver Proxy
In this approach, it is assumed that the sender is RSVP capable and
takes full care of the synchronization between application
requirements and RSVP reservations. With this approach, the RSVP
Receiver Proxy uses the RSVP Path messages generated by the sender as
the cue for establishing the RSVP reservation on behalf of the
receiver. The RSVP Receiver Proxy is effectively acting as a slave
making reservations (on behalf of the receiver) under the sender's
control. This changes somewhat the usual RSVP reservation model
where reservations are normally controlled by receivers. Such a
change greatly facilitates operations in the scenario of interest
here, which is where the receiver is not RSVP capable. Indeed it
allows the RSVP Receiver Proxy to remain application unaware by
taking advantage of the application awareness and RSVP awareness of
the sender.
With the Path-Triggered RSVP Receiver Proxy approach, the RSVP router
may be configured to use receipt of a regular RSVP Path message as
the trigger for RSVP Receiver Proxy behavior.
On receipt of the RSVP Path message, the RSVP Receiver Proxy:
1. establishes the RSVP Path state as per regular RSVP processing
2. identifies the downstream interface towards the receiver
3. sinks the Path message
4. behaves as if a Resv message (whose details are discussed below)
was received on the downstream interface. This includes
Le Faucheur, et al. Expires March 15, 2008 [Page 8]
Internet-Draft RSVP Proxy Approaches September 2007
performing admission control on the downstream interface,
establishing a Resv state (in case of successful admission
control) and forwarding the Resv message upstream, sending
periodic refreshes of the Resv message and tearing down the
reservation if the Path state is torn down.
In order to build the Resv message, the RSVP Receiver Proxy can take
into account information received in the Path message. For example,
the RSVP Receiver Proxy may compose a FLOWSPEC object for the Resv
message which mirrors the SENDER_TSPEC object in the received Path
message.
Operation of the Path-Triggered Receiver Proxy in the case of a
successful reservation is illustrated in Figure 3.
|----| *** *** |----------| |----|
| S |---------*r*----------*r*---------| RSVP |----------| R |
|----| *** *** | Receiver | |----|
| Proxy |
|----------|
---Path---> ----Path----> ---Path---->
<--Resv---> <---Resv----- <--Resv----
==================RSVP===============>
**********************************************************>
|----| RSVP-capable |----| Non-RSVP-capable ***
| S | Sender | R | Receiver *r* regular RSVP
|----| |----| *** router
***> media flow
==> segment of flow path protected by RSVP reservation
Figure 3: Path-Triggered RSVP Receiver Proxy
In case the reservation establishment is rejected (for example
because of an admission control failure on a regular RSVP router on
the path between the RSVP-capable sender and the RSVP Receiver
Proxy), a ResvErr message will be generated as per conventional RSVP
operations and will travel downstream towards the RSVP Receiver
Proxy. While this ensures that the RSVP Receiver Proxy is aware of
the reservation failure, conventional RSVP procedures do not cater
for notification of the sender of the reservation failure. Operation
Le Faucheur, et al. Expires March 15, 2008 [Page 9]
Internet-Draft RSVP Proxy Approaches September 2007
of the Path-Triggered RSVP Receiver Proxy in the case of an admission
control failure is illustrated in Figure 4.
|----| *** *** |----------| |----|
| S |---------*r*----------*r*---------| RSVP |----------| R |
|----| *** *** | Receiver | |----|
| Proxy |
|----------|
---Path---> ----Path----> ---Path---->
<---Resv----- <--Resv------
---ResvErr---> --ResvErr--->
===================RSVP===============>
**********************************************************>
|----| RSVP-capable |----| Non-RSVP-capable ***
| S | Sender | R | Receiver *r* regular RSVP
|----| |----| *** router
***> media flow
==> segment of flow path protected by RSVP reservation
Figure 4: Path-Triggered RSVP Receiver Proxy with Failure
Since, as explained above, in this scenario involving the RSVP
Receiver Proxy, synchronization between application and RSVP
reservation is generally performed by the sender, notifying the
sender of reservation failure is needed.
[I-D.ietf-tsvwg-rsvp-proxy-proto] specifies RSVP extensions allowing
such sender notification in case of reservation failure in the
presence of a Path-Triggered RSVP Receiver Proxy.
4.2. Path-Triggered Sender Proxy for Reverse Direction
In this approach, it is assumed that one endpoint is RSVP capable and
takes full care of the synchronization between application
requirements and RSVP reservations. This endpoint is the sender for
one flow direction (which we refer to as the "forward" direction) and
is the receiver for the flow in the opposite direction (which we
refer to as the "reverse" direction).
With the Path-Triggered Sender Proxy for Reverse Direction approach,
Le Faucheur, et al. Expires March 15, 2008 [Page 10]
Internet-Draft RSVP Proxy Approaches September 2007
the RSVP Proxy uses the RSVP signaling generated by the sender as the
cue for initiating RSVP signaling for the reservation in the reverse
direction. Thus, the RSVP Proxy is effectively acting as a Sender
Proxy for the reverse direction under the control of the sender for
the forward direction. Note that this assumes a degree of symmetry
for the two directions of the flow (as is currently typical for IP
telephony, for example). This is illustrated in Figure 5.
|----| *** *** |----------| |----|
| R |---------*r*----------*r*---------| RSVP |----------| S |
|----| *** *** | Sender | |----|
| Proxy |
|----------|
---Path---> ----Path----> ---Path---->
<--Path---> <---Path----- <--Path----
---Resv---> ----Resv----> ---Resv---->
<================RSVP==================
<**********************************************************
|----| RSVP-capable |----| Non-RSVP-capable ***
| R | Receiver | S | Sender *r* regular RSVP
|----| |----| *** router
***> media flow
==> segment of flow path protected by RSVP reservation
in reverse direction
Figure 5: Path-Triggered Sender Proxy for Reverse Direction
Of course, the RSVP Proxy may simultaneously (and typically will)
also act as the Path-Triggered Receiver Proxy for the forward
direction, as defined in Section 4.1. Such an approach is most
useful in situations involving RSVP reservations in both directions
for symmetric flows. This is illustrated in Figure 6.
Le Faucheur, et al. Expires March 15, 2008 [Page 11]
Internet-Draft RSVP Proxy Approaches September 2007
|----| *** *** |----------| |----|
|S/R |---------*r*----------*r*---------| RSVP |----------|S/R&|
|----| *** *** | Receiver | |----|
| & Sender |
| Proxy |
|----------|
---Path---> ----Path----> ---Path---->
<--Resv---> <---Resv----- <--Resv----
<--Path---> <---Path----- <--Path----
---Resv---> ----Resv----> ---Resv---->
================RSVP==================>
<================RSVP==================
**********************************************************>
<**********************************************************
|----| RSVP-capable |----| Non-RSVP-capable ***
|S/R | Sender and |S/R&| Sender and *r* regular RSVP
|----| Receiver |----| Receiver *** router
***> media flow
==> segment of flow path protected by RSVP reservation
in forward and in reverse direction
Figure 6: Path Triggered Receiver & Sender Proxy
With the Path-Triggered Sender Proxy for Reverse Direction approach,
the RSVP router may be configurable to use receipt of a regular RSVP
Path message as the trigger for Sender Proxy for Reverse Direction
behavior.
On receipt of the RSVP Path message for the forward direction, the
RSVP Sender Receiver Proxy :
1. sinks the Path message
2. behaves as if a Path message for reverse direction (whose details
are discussed below) had been received by the Sender Proxy. This
includes establishing the corresponding Path state, forwarding
the Path message downstream, sending periodic refreshes of the
Le Faucheur, et al. Expires March 15, 2008 [Page 12]
Internet-Draft RSVP Proxy Approaches September 2007
Path message and tearing down the Path in reverse direction when
the Path state in forward direction is torn down.
In order to build the Path message for the reverse direction, the
RSVP Sender Proxy can take into account information in the received
Path message for the forward direction. For example, the RSVP Sender
Proxy may mirror the SENDER_TSPEC object in the received Path
message.
We observe that this approach does not require any extensions to the
existing RSVP protocol.
4.3. Inspection-Triggered Proxy
In this approach, it is assumed that the RSVP Proxy is on the
datapath of "packets of interest", that it can inspect such packets
on the fly as they transit through it, and that it can infer
information from these packets of interest to determine what RSVP
reservations need to be established, when and with what
characteristics (possibly also using some configured information).
One example of "packets of interest" could be application level
signaling. An RSVP Proxy capable of inspecting SIP signaling for
multimedia session or RTSP signaling for Video streaming, can obtain
from such signaling information about when a multimedia session is up
or when a Video is going to be streamed. It can also identify the
addresses and ports of senders and receivers and can determine the
bandwidth of the corresponding flows. Thus, such an RSVP Proxy can
determine all necessary information to synchronize RSVP reservations
to application requirements. This is illustrated in Figure 7.
Le Faucheur, et al. Expires March 15, 2008 [Page 13]
Internet-Draft RSVP Proxy Approaches September 2007
|-------------|
| Application |
| Signaling |
| Entity |
|-------------|
/ \
/ \
/ \
</////////////////////// \\\\\\\\\\\\\\\\\\\\\\\\>
|----| |--------| *** |--------| |----|
| S |--------| RSVP |------*r*--------| RSVP |----------| R |
|----| | Proxy | *** | Proxy | |----|
|--------| |--------|
=======RSVP=======>
********************************************************>
|----| Non-RSVP-capable |----| Non-RSVP-capable ***
| S | Sender | R | Receiver *r* regular RSVP
|----| |----| *** router
</\> application level signaling
***> media flow
==> segment of flow path protected by RSVP reservation
Figure 7: Inspection-Triggered RSVP Proxy
Another example of "packets of interest" could be packets belonging
to the application flow itself (e.g. media packets). An RSVP Proxy
capable of detecting the transit of packets from a particular flow,
can attempt to establish a reservation corresponding to that flow.
Characteristics of the reservation may be derived from configuration,
flow measurement or a combination of those.
Note however, that in case of reservation failure, the inspection-
triggered RSVP Proxy does not have a direct mechanism for notifying
the application (since it is not participating itself actively in
application signaling) so that the application takes appropriate
action (for example terminate the corresponding session). To
mitigate this problem, the inspection-triggered RSVP Proxy may mark
differently the DSCP of flows for which an RSVP reservation has been
successfully proxied from the flows for which a reservation is not in
Le Faucheur, et al. Expires March 15, 2008 [Page 14]
Internet-Draft RSVP Proxy Approaches September 2007
place. In some situations, the Inspection-Triggered Proxy might be
able to modify the "packets of interest" (e.g. application signaling
messages) to convey some hint to applications that the corresponding
flows cannot be guaranteed by RSVP reservations.
With the inspection-triggered Proxy approach, the RSVP Receiver Proxy
is effectively required to attempt to build application awareness by
traffic inspection and then is somewhat limited in the actions in can
take in case of reservation failure. However, this may be a useful
approach in some environments. Note also that this approach does not
require any change to the RSVP protocol.
With the "Inspection-Triggered" RSVP Proxy approach, the RSVP router
may be configurable to use and interpret some specific "packets of
interest" as the trigger for RSVP Receiver Proxy behavior.
4.4. STUN-Triggered Proxy
In this approach, the RSVP Proxy takes advantage of the application
awareness provided by the STUN signaling to synchronize RSVP
reservations with application requirements. The STUN signaling is
sent from endpoint to endpoint. This is illustrated in Figure 8.
Le Faucheur, et al. Expires March 15, 2008 [Page 15]
Internet-Draft RSVP Proxy Approaches September 2007
|----| |--------| *** |--------| |----|
| S |--------| RSVP |------*r*--------| RSVP |----------| R |
|----| | Proxy | *** | Proxy | |----|
|--------| |--------|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^>
=======RSVP=======>
********************************************************>
|----| Non-RSVP-capable |----| Non-RSVP-capable ***
| S | Sender | R | Receiver *r* regular RSVP
|----| |----| *** router
^^^> STUN message flow (over same UDP ports as media flow)
==> segment of flow path protected by RSVP reservation
***> RTP media flow
Figure 8: STUN-Triggered Proxy
In this approach, a STUN [I-D.ietf-behave-rfc3489bis] message
triggers the RSVP Proxy. The STUN message could also include (yet-
to-be-specified) STUN attributes to indicate information such as the
bandwidth and application requesting the flow, which would allow the
RSVP proxy agent to create an appropriately-sized reservation for
each flow.
For unicast flows, [I-D.ietf-mmusic-ice] is an already widely-adopted
emerging standard for NAT traversal. For our purposes of triggering
RSVP Proxy behavior, we rely on ICE's connectivity check -- the
exchange of STUN Binding Request messages between hosts to verify
connectivity (see section 2.2 of [I-D.ietf-mmusic-ice]). By
including new STUN attributes in those connectivity check messages,
an RSVP Proxy agent could perform its functions more effectively.
Additionally, the RSVP Proxy agent can inform endpoints of an RSVP
reservation failure by dropping the ICE connectivity check message or
sending ICMP messages back to the endpoint. This provides very RSVP-
like call admission control and signaling to the endpoints, without
implementing RSVP on the endpoints, and also operates through NATs.
For multicast flows (or certain kinds of unicast flows that don't or
can't use ICE), a STUN Indication message
[I-D.ietf-behave-rfc3489bis] could indicate the flow's bandwidth,
Le Faucheur, et al. Expires March 15, 2008 [Page 16]
Internet-Draft RSVP Proxy Approaches September 2007
providing a benefit similar to the ICE connectivity check. STUN
Indication messages are not acknowledged by the receiver and have the
same scalability as the underlying multicast flow.
The corresponding extensions to ICE and STUN for such a STUN-
triggered RSVP Proxy approach are beyond the scope of this document.
They may be defined in the future in a separate document.
4.5. Application_Entity-Controlled Proxy
In this approach, it is assumed that an entity involved in the
application level signaling controls an RSVP Proxy which is located
in the datapath of the application flows (i.e. "on-path"). With this
approach, the RSVP Proxy does not attempt to determine itself the
application reservation requirements. Instead the RSVP Proxy is
instructed by the entity participating in application level signaling
to establish, maintain and tear down reservations as needed by the
application flows. In other words, with this approach, the solution
for synchronizing RSVP signaling with application level requirements
is to rely on an application-level signaling entity that controls an
RSVP Proxy function that sits in the flow datapath. This approach
allows control of an RSVP Sender Proxy, an RSVP Receiver Proxy or
both.
Operation of the Application_Entity-Controlled Proxy is illustrated
in Figure 9.
Le Faucheur, et al. Expires March 15, 2008 [Page 17]
Internet-Draft RSVP Proxy Approaches September 2007
|---------| |---------|
/////////| App |////\\\\| App |\\\\\\\\
/ | Entity | | Entity | \
/ |---------| |---------| \
/ // \\ \
/ // \\ \
/ // \\ \
/ // \\ \
/ // \\ \
|----| |--------| *** |---------| |----|
| S |----------| |------*r*-------| |---------| R |
|----| | RSVP | *** | RSVP | |----|
| Sender | | Receiver|
| Proxy | | Proxy |
|--------| |---------|
=======RSVP=======>
********************************************************>
|----| Non-RSVP-capable |----| Non-RSVP-capable ***
| S | Sender | R | Receiver *r* regular RSVP
|----| |----| *** router
***> media flow
==> segment of flow path protected by RSVP reservation
/\ Application signaling (e.g. SIP)
// RSVP Proxy control interface
Figure 9: Application_Entity-Controlled Proxy
As an example, the Application_Entity-Controlled Proxy may be used in
the context of Session Border Controllers (SBCs) (see
[I-D.ietf-sipping-sbc-funcs] for description of SBCs) to establish
RSVP reservations for multimedia sessions. In that case, the
Application Entity may be the signaling component of the SBC.
This RSVP Proxy approach does not require any extension to the RSVP
protocol. However, it relies on an RSVP Proxy control interface
allowing control of the RSVP Proxy by an application signaling
entity. This RSVP Proxy control interface is beyond the scope of the
present document. Candidate protocols for realizing such interface
include SNMP, COPS-PR, QPIM, XML and DIAMETER. This interface may
Le Faucheur, et al. Expires March 15, 2008 [Page 18]
Internet-Draft RSVP Proxy Approaches September 2007
rely on soft states or hard states. Clearly, when hard states are
used, those need to be converted appropriately by the RSVP Proxy
entities into the corresponding RSVP soft states.
In general, the Application Entity is not expected to maintain
awareness of which RSVP Receiver Proxy is on the path to which
destination. However, in the particular cases where it does so
reliably, we observe that the Application Entity could control the
RSVP Sender Proxy and Receiver Proxy so that aggregate RSVP
reservations are used between those, instead of one reservation per
flow. For example, these aggregate reservations could be of RSVP-
AGGREGATE type as specified in [RFC3175] or of GENERIC-AGGREGATE type
as specified in [RFC4860]. Such aggregate reservations could be used
so that a single reservation can be used for multiple (possibly all)
application flows transiting via the same RSVP Sender Proxy and the
same RSVP Receiver Proxy.
For situations where only the RSVP Sender Proxy has to be controlled
by this interface, the interface may be realized through the simple
use of RSVP itself, over a GRE tunnel from the application entity to
the RSVP Sender Proxy. This particular case is further discussed in
Section 4.5.1. Another particular case of interest is where the
application signaling entity resides on the same device as the RSVP
Proxy. In that case, this interface may be trivially realized as an
internal API. An example environment based on this particular case
is illustrated in Section 4.5.2.
4.5.1. Application_Entity-Controlled Sender Proxy using "RSVP over GRE"
This approach is simply a particular case of the more general
Application_Entity-Controlled Proxy, but where only RSVP Sender
Proxies need to be controlled by the application, and where RSVP is
effectively used as the control protocol between the application
signaling entity and the RSVP Sender Proxy.
In this approach, the RSVP messages (e.g. RSVP Path message) are
effectively generated by the application entity and logically
"tunnelled" to the RSVP Sender Proxy via GRE tunneling. This is to
ensure that the RSVP messages follow the exact same path as the flow
they protect (as required by RSVP operations) on the segment of the
end-to-end path which is to be subject to RSVP reservations.
Figure 10 illustrates such an environment.
Le Faucheur, et al. Expires March 15, 2008 [Page 19]
Internet-Draft RSVP Proxy Approaches September 2007
|-------------|
////////////| Application |\\\\\\\\\
/ | Entity | \
/ |-------------| \
/ /=/ \
/ /=/ \
/ /=/ \
/ /=/ \
/ /=/ \
/ /=/ \
/ /=/ \
/ /=/ \
|----| |--------| *** |----|
| S |-----------| RSVP |-----------*r*-----------------| R |
|----| | Sender | *** |----|
| Proxy |
|--------|
=========RSVP====================>
*****************************************************>
|----| non-RSVP-capable |----| RSVP-capable ***
| S | Sender | R | Receiver *r* regular RSVP
|----| |----| *** router
***> media flow
==> segment of flow path protected by RSVP reservation
/\ Application level signaling
/=/ GRE-tunnelled RSVP (Path messages)
Figure 10: Application-Entity-Controlled Sender Proxy via "RSVP over
GRE"
With the Application_Entity-Controlled Sender Proxy using "RSVP Over
GRE", the application entity :
o generates a Path message on behalf of the sender, corresponding to
the reservation needed by the application and maintains the
corresponding Path state. The Path message built by the
application entity is exactly the same as would be built by the
actual sender (if it was RSVP-capable), with one single exception
which is that the Application Entity puts its own IP address as
the RSVP Previous Hop. In particular, it is recommended that the
Le Faucheur, et al. Expires March 15, 2008 [Page 20]
Internet-Draft RSVP Proxy Approaches September 2007
source address of the Path message built by the application entity
be set to the IP address of the sender (not of the application
entity). This helps ensuring that, in the presence of non-RSVP
routers and of load-balancing in the network where the load-
balancing algorithm takes into account the source IP address, the
Path message generated by the application entity follows the exact
same path that the actual stream sourced by the sender.
o encapsulates the Path message into a GRE tunnel whose destination
address is the RSVP Sender Proxy i.e. an RSVP Router sitting on
the datapath for the flow (and upstream of the segment which
requires QoS guarantees via RSVP reservation).
o processes the corresponding received RSVP messages (including Resv
messages) as per regular RSVP.
o synchronizes the RSVP reservation state with application level
requirements and signaling.
Note that since the application entity encodes its own IP address as
the RSVP PHOP in the Path message, the RSVP Router terminating the
GRE tunnel naturally addresses all the RSVP messages travelling
upstream hop-by-hop (such as Resv messages) to the application entity
(without having to encapsulate those in a reverse-direction GRE
tunnel towards the application entity).
4.5.2. Application_Entity-Controlled Proxy via Co-Location
This approach is simply a particular case of the more general
Application_Entity-Controlled Proxy, but where the application entity
is co-located with the RSVP Proxy. As an example, Session Border
Controllers (SBC) with on-board SIP agents could implement RSVP Proxy
functions and make use of such an approach to achieve session
admission control over the SBC-to-SBC segment using RSVP signaling.
Figure 11 illustrates operations of the Application_Entity-Controlled
RSVP Proxy via Co-location.
Le Faucheur, et al. Expires March 15, 2008 [Page 21]
Internet-Draft RSVP Proxy Approaches September 2007
|---------| |---------|
////////| App |////////\\\\\\\| App |\\\\\\\\\
/ | Entity | | Entity | \
/ | | | | \
|----| |---------| *** |---------| |----|
| S |--------| RSVP |------*r*------| RSVP |---------| R |
|----| | Sender | *** | Receiver| |----|
| Proxy | | Proxy |
|---------| |---------|
=======RSVP======>
*******************************************************>
|----| Non-RSVP-capable |----| Non-RSVP-capable ***
| S | Sender | R | Receiver *r* regular RSVP
|----| |----| *** router
***> media flow
==> segment of flow path protected by RSVP reservation
/\ Application level signaling
Figure 11: Application_Entity-Controlled Proxy via Co-Location
This RSVP Proxy approach does not require any protocol extensions.
We also observe that when multiple sessions are to be established on
paths sharing the same RSVP Sender Proxy and the same RSVP Receiver
Proxy, the RSVP Proxies have the option to establish aggregate RSVP
reservations (as defined in ([RFC3175] or [RFC4860]) for a group of
sessions, instead of establishing one RSVP reservation per session.
4.6. Policy_Server-Controlled Proxy
In this approach, it is assumed that a Policy Server, which is
located in the control plane of the network, controls an RSVP Proxy
which is located in the datapath of the application flows (i.e. "on-
path"). In turn, the Policy server is triggered by an entity
involved in the application level signaling. With this approach, the
RSVP Proxy does not attempt to determine itself the application
reservation requirements, but instead is instructed by the Policy
Server to establish, maintain and tear down reservations as needed by
the application flows. Moreover, the entity participating in
application level signaling does not attempt to understand the
specific reservation mechanism (i.e. RSVP) or the topology of the
network layer, but instead it simply asks the policy server to
Le Faucheur, et al. Expires March 15, 2008 [Page 22]
Internet-Draft RSVP Proxy Approaches September 2007
perform (or teardown) a reservation. In other words, with this
approach, the solution for synchronizing RSVP signaling with
application level requirements is to rely on an application level
entity that controls a policy server that, in turn, controls an RSVP
Proxy function that sits in the flow datapath. This approach allows
control of an RSVP Sender Proxy, an RSVP Receiver Proxy or both.
Operation of the Policy_Server-Controlled Proxy is illustrated
Figure 12.
Le Faucheur, et al. Expires March 15, 2008 [Page 23]
Internet-Draft RSVP Proxy Approaches September 2007
|---------|
/////////////| App |\\\\\\\\\\\\\\
/ | Entity | \
/ |---------| \
/ I \
/ I \
/ |----------| \
/ | Policy | \
/ | Server | \
/ |----------| \
/ // \\ \
/ // \\ \
/ // \\ \
|----| |--------| *** |---------| |----|
| S |-----------| |------*r*-----| |----------| R |
|----| | RSVP | *** | RSVP | |----|
| Sender | | Receiver|
| Proxy | | Proxy |
|--------| |---------|
=====RSVP========>
**********************************************************>
|----| Non-RSVP-capable |----| Non-RSVP-capable ***
| S | Sender | R | Receiver *r* regular RSVP
|----| |----| *** router
***> media flow
==> segment of flow path protected by RSVP reservation
/\ Application signaling (e.g. SIP)
// RSVP Proxy control interface
I Interface between Application Entity and Policy Server
Figure 12: Policy_Server-Controlled Proxy
This RSVP Proxy approach does not require any extension to the RSVP
protocol. However, as with the Application_Entity-Controlled Proxy
approach presented in Figure 9, this approach relies on an RSVP Proxy
control interface allowing control of the RSVP Proxy (by the Policy
Server in this case). This RSVP Proxy control interface is beyond
the scope of the present document. Considerations about candidate
protocols for realizing such interface can be found in Section 4.5.
Le Faucheur, et al. Expires March 15, 2008 [Page 24]
Internet-Draft RSVP Proxy Approaches September 2007
Again, for situations where only the RSVP Sender Proxy has to be
controlled by this interface, the interface may be realized through
the simple use of RSVP Itself, over a GRE tunnel from the Policy
Server to the RSVP Sender Proxy. This is similar to what is
presented in Section 4.5.1 except that the "RSVP over GRE" interface
is used in this case by the Policy Server (instead of the application
entity).
The interface between the Application Entity and the Policy Server is
beyond the scope of this document.
4.7. RSVP-Signaling-Triggered Proxy
An RSVP Proxy can also be triggered and controlled through extended
RSVP signaling from the remote end that is RSVP-capable (and supports
these RSVP extensions for Proxy control). For example, an RSVP
capable sender could send a new or extended RSVP message explicitly
requesting an RSVP Proxy on the path towards the receiver to behave
as an RSVP Receiver Proxy and also to trigger a reverse direction
reservation thus also behaving as a RSVP Sender Proxy. The new or
extended RSVP message sent by the sender could also include
attributes (e.g. bandwidth) for the reservations to be signaled by
the RSVP Proxy.
The challenges in these explicit signaling schemes include:
o How can the nodes determine when a reservation request ought to be
proxied and when it should not, and accordingly invoke appropriate
signaling procedures?
o How does the node sending the messages explicitly triggering the
Proxy know where the Proxy is located, e.g., determine an IP
address of the proxy that should reply to the signaling?
o How is all the information needed by a Sender Proxy to generate a
Path message actually communicated to the Proxy?
An example of such a mechanism is presented in
[I-D.manner-tsvwg-rsvp-proxy-sig]. This scheme is primarily targeted
to local access network reservations whereby an end host can request
resource reservations for both incoming and outgoing flows only over
the access network. This may be useful in environments where the
access network is typically the bottleneck while the core is
comparatively over-provisioned, as may be the case with a number of
radio access technologies. In this proposal, messages targeted to
the Proxy are flagged with one bit in all RSVP messages. Similarly,
all RSVP messages sent back by the Proxy are also flagged. The use
of such a flag allows differentiating between proxied and end-to-end
Le Faucheur, et al. Expires March 15, 2008 [Page 25]
Internet-Draft RSVP Proxy Approaches September 2007
reservations. For triggering an RSVP Receiver Proxy, the sender of
the data sends a Path message which is marked with the mentioned
flag. The Receiver Proxy is located on the signaling and data path,
eventually gets the Path message, and replies back with a Resv
message. A node triggers an RSVP Sender Proxy with a newly defined
Path_Request message, which instructs the proxy to send Path messages
towards the triggering node. The node then replies back with a Resv.
More details can be found in [I-D.manner-tsvwg-rsvp-proxy-sig].
Such an RSVP-Signaling-Triggered Proxy approach would require RSVP
signaling extensions (that are outside the scope of the present
document). However it could provide more flexibility in the control
of the Proxy behavior (e.g. control of reverse reservation
parameters) than provided by the Path-Triggered approaches defined in
Section 4.1 and Section 4.2.
4.8. Endsystem-Controlled Proxy
In some cases, having a full RSVP implementation running on an end
host can be seen to produce excessive overhead. In end-hosts that
are low in processing power and functionality, having an RSVP daemon
run and take care of the signaling may introduce unnecessary
overhead. One article [Kars01] proposes to create a remote API so
that the daemon would in fact run on the end-host's default router
and the end-host application would send its requests to that daemon.
Thus, we can have deployments, where an end host uses some
lightweight protocol to communicate with its pre-defined RSVP router
- a form of RSVP proxy. Such a lightweight protocol is outside the
scope of the present document.
4.9. Reachability Considerations
There may be situations where the RSVP Receiver Proxy is reachable by
the sender, while the receiver itself is not. In such situations, it
is possible that the RSVP Receiver Proxy is not always aware that the
receiver is unreachable, and consequently may accept to establish an
RSVP reservation on behalf of that receiver. This would result in
unnecessary reservation establishment and unnecessary network
resource consumption.
This is not considered a significant practical concern for a number
of reasons. First, in many cases, if the receiver is not reachable
from the sender, it will not be reachable either for application
signaling so that application level session establishment will not be
possible in the first place. Secondly, where the receiver is
unreachable from the sender but is reachable for application level
signaling (say because session establishment is performed through an
off-path SIP agent that uses a different logical topology to
Le Faucheur, et al. Expires March 15, 2008 [Page 26]
Internet-Draft RSVP Proxy Approaches September 2007
communicate with the receiver), then the sender may detect that the
receiver is unreachable before attempting reservation establishment.
This may be achieved through mechanisms such as ICE's connectivity
check ( [I-D.ietf-mmusic-ice]). Finally, even if the sender does not
detect that the receiver is unreachable before triggering the RSVP
reservation establishment, it is very likely that the application
will quickly realise this lack of connectivity (e.g. the human
accepting the phone call on the receiver side will not hear the
human's voice on the sender side) and therefore tear down the session
(e.g. hang up the phone) which in turn will trigger RSVP reservation
release.
Nonetheless, it is recommended that network administrators consider
the above in light of their particular environment when deploying
RSVP Proxys.
The mirror considerations apply for situations involving an RSVP
Sender Proxy and where the sender cannot reach the destination while
the RSVP Sender Proxy can.
5. Security Considerations
In the environments of concern for this document, RSVP messages are
used to control resource reservations on a segment of the end-to-end
path of flows. To ensure the integrity of the associated reservation
and admission control mechanisms, the cryptographic authentication
mechanisms defined in [RFC2747]] and [RFC3097] can be used. Those
protect RSVP messages integrity hop-by-hop and provide node
authentication, thereby protecting against corruption, spoofing of
RSVP messages and replay.
[I-D.behringer-tsvwg-rsvp-security-groupkeying] discusses key types,
key provisioning methods as well as their respective applicability.
A number of additional security considerations apply to the use of
RSVP proxies and are discussed below.
With some RSVP Proxy approaches, the RSVP proxy operates autonomously
inside an RSVP router. This is the case for the Path-Triggered Proxy
approaches defined in Section 4.1 and in Section 4.2, for the
Inspection-Triggered Proxy approach defined in Section 4.3, for the
STUN-Triggered Proxy approach defined in Section 4.4 and for the
RSVP-Signaling-Triggered approach defined in Section 4.7. Proper
reservation operation assumes that the RSVP proxy can be trusted to
behave correctly in order to control the RSVP reservation as required
and expected by the end systems. Since, the basic RSVP operation
already assumes a trust model where end-systems trust RSVP nodes to
appropriately perform RSVP reservations, the use of RSVP proxy that
Le Faucheur, et al. Expires March 15, 2008 [Page 27]
Internet-Draft RSVP Proxy Approaches September 2007
behave autonomously within an RSVP router is not seen as introducing
any significant additional security threat or as fundamentally
modifying the RSVP trust model.
With some RSVP Proxy approaches, the RSVP proxy operate under the
control of another entity. This is the case for the
Application_Entity-Controlled Proxy approach defined in Section 4.5
and for the Policy_Server-Controlled Proxy approach defined in
Section 4.6. This introduces additional security risks since the
entity controlling the RSVP Proxy needs to be trusted for proper
reservation operation. The exact mechanisms to establish such trust
are beyond the scope of this document, but they may include security
mechanisms inside the protocol used as the control interface between
the RSVP Proxy and the entity controlling it, as well as security
mechanisms for all the interfaces involved in the reservation control
chain (e.g. inside the application signaling protocol between the end
systems and the application entity, and, in the case of the
Policy_Server-Controlled Proxy approach, in the protocol between the
application entity and the policy server).
In some situations, the use of RSVP Proxy to control reservations on
behalf of end-systems may actually reduce the security risk (at least
from the network operator viewpoint). This could be the case, for
example, because the routers where the RSVP Proxy functionality runs
are less exposed to tampering than end-systems. Such a case is
further discussed in section 4 of [I-D.ietf-tsvwg-rsvp-proxy-proto].
6. IANA Considerations
This document does not make any request to IANA registration.
7. Acknowledgments
This document benefited from earlier work on the concept of RSVP
Proxy including the one documented by Silvano Gai, Dinesh Dutt,
Nitsan Elfassy and Yoram Bernet. It also benefited from discussions
with Pratik Bose, Chris Christou and Michael Davenport. Tullio
Loffredo and Massimo Sassi provided the base material for
Section 4.6.
8. Informative References
[I-D.behringer-tsvwg-rsvp-security-groupkeying]
Behringer, M. and F. Le Faucheur, "A Framework for RSVP
Security Using Dynamic Group Keying", July 2007.
Le Faucheur, et al. Expires March 15, 2008 [Page 28]
Internet-Draft RSVP Proxy Approaches September 2007
[I-D.ietf-behave-rfc3489bis]
Rosenberg, J., Huitema, C., Mahy, R., Matthews, P., and D.
Wing, "Session Traversal Utilities for (NAT) (STUN)",
draft-ietf-behave-rfc3489bis-09 (work in progress),
August 2007.
[I-D.ietf-mmusic-ice]
Rosenberg, J., "Interactive Connectivity Establishment
(ICE): A Protocol for Network Address Translator (NAT)
Traversal for Offer/Answer Protocols",
draft-ietf-mmusic-ice-17 (work in progress), July 2007.
[I-D.ietf-sipping-sbc-funcs]
Hautakorpi, J., Camarillo, G., Penfield, R., Hawrylyshen,
A., and M. Bhatia, "Requirements from SIP (Session
Initiation Protocol) Session Border Control Deployments",
April 2007.
[I-D.ietf-tsvwg-rsvp-proxy-proto]
Le Faucheur, L., "RSVP Extensions For Path-Triggered RSVP
Receiver Proxy", February 2007.
[I-D.ietf-tsvwg-vpn-signaled-preemption]
Baker, F. and P. Bose, "QoS Signaling in a Nested Virtual
Private Network", February 2007.
[I-D.manner-tsvwg-rsvp-proxy-sig]
Manner, J., "Localized RSVP for Controlling RSVP Proxies",
October 2006.
[Kars01] Karsten, M., "Experimental Extensions to RSVP -- Remote
Client and One-Pass Signalling", IWQoS Karlsruhe, Germany,
2006.
[RFC1633] Braden, B., Clark, D., and S. Shenker, "Integrated
Services in the Internet Architecture: an Overview",
RFC 1633, June 1994.
[RFC2205] Braden, B., Zhang, L., Berson, S., Herzog, S., and S.
Jamin, "Resource ReSerVation Protocol (RSVP) -- Version 1
Functional Specification", RFC 2205, September 1997.
[RFC2210] Wroclawski, J., "The Use of RSVP with IETF Integrated
Services", RFC 2210, September 1997.
[RFC2475] Blake, S., Black, D., Carlson, M., Davies, E., Wang, Z.,
and W. Weiss, "An Architecture for Differentiated
Services", RFC 2475, December 1998.
Le Faucheur, et al. Expires March 15, 2008 [Page 29]
Internet-Draft RSVP Proxy Approaches September 2007
[RFC2747] Baker, F., Lindell, B., and M. Talwar, "RSVP Cryptographic
Authentication", RFC 2747, January 2000.
[RFC2961] Berger, L., Gan, D., Swallow, G., Pan, P., Tommasi, F.,
and S. Molendini, "RSVP Refresh Overhead Reduction
Extensions", RFC 2961, April 2001.
[RFC3097] Braden, R. and L. Zhang, "RSVP Cryptographic
Authentication -- Updated Message Type Value", RFC 3097,
April 2001.
[RFC3175] Baker, F., Iturralde, C., Le Faucheur, F., and B. Davie,
"Aggregation of RSVP for IPv4 and IPv6 Reservations",
RFC 3175, September 2001.
[RFC3312] Camarillo, G., Marshall, W., and J. Rosenberg,
"Integration of Resource Management and Session Initiation
Protocol (SIP)", RFC 3312, October 2002.
[RFC3525] Groves, C., Pantaleo, M., Anderson, T., and T. Taylor,
"Gateway Control Protocol Version 1", RFC 3525, June 2003.
[RFC4301] Kent, S. and K. Seo, "Security Architecture for the
Internet Protocol", RFC 4301, December 2005.
[RFC4860] Le Faucheur, F., Davie, B., Bose, P., Christou, C., and M.
Davenport, "Generic Aggregate Resource ReSerVation
Protocol (RSVP) Reservations", RFC 4860, May 2007.
Appendix A. Use Cases for RSVP Proxies
A.1. RSVP-based VoD CAC in Broadband Aggregation Networks
As broadband services for residential are becoming more and more
prevalent, next generation aggregation networks are being deployed in
order to aggregate traffic from broadband users (whether attached via
Digital Subscriber Line technology aka DSL, Fiber To The Home/Curb
aka FTTx, Cable or other broadband access technology). Video on
Demand (VoD) services which may be offered to broadband users present
significant capacity planning challenges for the aggregation network
for a number of reasons. First each VoD stream requires significant
dedicated sustained bandwidth (typically 2-4 Mb/s in Standard
Definition TV and 6-12 Mb/s in High Definition TV). Secondly, the
VoD codec algorithms are very sensitive to packet loss. Finally, the
load resulting from such services is very hard to predict (e.g. it
can vary very suddenly with block-buster titles made available as
well as with promotional offerings). As a result, transport of VoD
Le Faucheur, et al. Expires March 15, 2008 [Page 30]
Internet-Draft RSVP Proxy Approaches September 2007
streams on the aggregation network usually translate into a strong
requirement for admission control. The admission control solution
protects the quality of established VoD sessions by rejecting the
additional excessive session attempts during unpredictable peaks,
during link or node failures, or combination of those factors.
RSVP can be used in the aggregation network for admission control of
the VoD sessions. However, since Customer Premises equipment such as
Set Top Boxes (which behave as the receiver for VoD streams) often do
not support RSVP, the last IP hop in the aggregation network can
behave as an RSVP Receiver Proxy. This way, RSVP can be used between
VoD Pumps and the last IP hop in the Aggregation network to perform
accurate admission control of VoD streams over the resources set
aside for VoD in the aggregation network (typically a certain
percentage of the bandwidth of any link). As VoD streams are
unidirectional, a simple "Path-Triggered" RSVP Receiver Proxy (as
described in Section 4.1) is all that is required in this use case.
The Figure below illustrates operation of RSVP-based admission
control of VoD sessions in an Aggregation network involving RSVP
support on the VoD Pump (the senders) and RSVP Receiver Proxy on the
last IP hop of the aggregation network. All the customer premises
equipment remain RSVP unaware.
Le Faucheur, et al. Expires March 15, 2008 [Page 31]
Internet-Draft RSVP Proxy Approaches September 2007
|-------------|
| VoD SRM |
| |
////////| |\\\\\\\\\\\\\\\
/ |-------------| \
/ \
/ \
/ \
/ \
/ \
|----| |------| *** *** |--------| |-----| |---|
| VoD|--|RSVP |----*r*--*r*--|RSVP |--|DSLAM|~~~~|STB|--TV
|Pump| |Router| *** *** |Receiver| |-----| |---|
|----| |------| |Proxy |
|--------|
<---Aggregation Net------------->
******************************************************>
============RSVP====================>
SRM Session Resource Manager
*** |---|
*r* regular RSVP |STB| Set Top Box
*** router |---|
***> VoD media flow
==> segment of flow path protected by RSVP reservation
/\ VoD Application level signaling (e.g. RTSP)
Figure 13: VoD Use Case with Receiver Proxy
In the case where the VoD Pumps are not RSVP-capable, an
Application_Entity-Controlled Sender Proxy via "RSVP over GRE"
approach (as described in Section 4.5.1) can also be implemented on
the VoD Controller or Session Resource Manager (SRM) devices
typically involved in VoD deployments. Figure 14 illustrates
operation of RSVP-based admission control of VoD sessions in an
Aggregation network involving such Application_Entity-Controlled
Source Proxy combined with an RSVP Receiver Proxy on the last IP hop
of the aggregation network. All the customer premises equipment, as
well as the VoD pumps, remain RSVP unaware.
Le Faucheur, et al. Expires March 15, 2008 [Page 32]
Internet-Draft RSVP Proxy Approaches September 2007
|-------------|
////| VoD SRM |\\\\\\\\\\\
/ | | \
/ | + | \
/ | RSVP Sender | \
/ |Proxy Control| \
/ |-------------| \
/ /=/ \
/ /=/ \
/ /=/ \
/ /=/ \
/ /=/ \
|----| |------| *** *** |--------| |-----| |---|
| VoD|--|RSVP |----*r*--*r*--|RSVP |--|DSLAM|~~~~|STB|--TV
|Pump| |Sender| *** *** |Receiver| |-----| |---|
|----| |Proxy | |Proxy |
|------| |--------|
<---Aggregation Net------------->
******************************************************>
=========RSVP==============>
SRM Systems Resource Manager
*** |---|
*r* regular RSVP |STB| Set Top Box
*** router |---|
***> VoD media flow
==> segment of flow path protected by RSVP reservation
/ VoD Application level signaling (e.g. RTSP)
/=/ GRE-tunnelled RSVP (Path messages)
Figure 14: VoD Use Case with Receiver Proxy and SRM-based Sender
Proxy
The RSVP Proxy entities specified in this document play a significant
role here since they allow immediate deployment of an RSVP-based
admission control solution for VoD without requiring any upgrade to
the huge installed base of non-RSVP-capable customer premises
equipment. In one mode described above, they also avoid upgrade of
non-RSVP-capable VoD pumps. In turn, this means that the benefits of
Le Faucheur, et al. Expires March 15, 2008 [Page 33]
Internet-Draft RSVP Proxy Approaches September 2007
on-path admission control can be offered to VoD services over
broadband aggregation networks without network or VoD Pump upgrade.
Those include accurate bandwidth accounting regardless of topology
(hub-and-spoke, ring, mesh, star, arbitrary combinations) and dynamic
adjustment to any change in topology (such as failure, routing
change, additional links...).
A.2. RSVP-based Voice/Video CAC in Enterprise WAN
More and more enterprises are migrating their telephony and
videoconferencing applications onto IP. When doing so, there is a
need for retaining admission control capabilities of existing TDM-
based systems to ensure the QoS of these applications is maintained
even when transiting through the enterprise's Wide Area Network
(WAN). Since many of the endpoints already deployed (such as IP
Phones or Videoconferencing terminals) are not RSVP capable, RSVP
Proxy approaches are very useful: they allow deployment of an RSVP-
based admission control solution over the WAN without requiring
upgrade of the existing terminals.
A common deployment architecture for such environments relies on the
Application_Entity-Controlled Proxy approach as defined in
Section 4.5. Routers sitting at the edges of the WAN network and
naturally "on-path" for all inter-campus calls (or sessions) and
behave as RSVP Proxies. The RSVP Proxies establish, maintain and
tear-down RSVP reservations over the WAN segment for the calls (or
sessions) under the control of the SIP Server/Proxy. The SIP Server/
Proxy synchronizes the RSVP reservation status with the status of
end-to-end calls. For example, the called IP phone will only be
instructed to play a ring tone if the RSVP reservations over the
corresponding WAN segment has been successfully established.
This architecture allowing RSVP-based admission control of voice and
video on the Enterprise WAN is illustrated in Figure 15.
Le Faucheur, et al. Expires March 15, 2008 [Page 34]
Internet-Draft RSVP Proxy Approaches September 2007
|---------|
//////////////| SIP |\\\\\\\\\\\\
/ | Server/ | \
/ | Proxy | \
/ |---------| \
/ // \\ \
/ // \\ \
/ // \\ \
/ // \\ \
/ // \\ \
|-----| |--------| *** *** |--------| |-----|
| IP |------| Media |---*r*---*r*---| Media |-------|IP |
|Phone| | Relay | *** *** | Relay | |Phone|
|-----| | + | | + | |-----|
| RSVP | | RSVP |
| Proxy | | Proxy |
|--------| |--------|
<--campus--> <--campus-->
network network
<---------WAN----------->
<*************> <***********************> <**************>
<=========RSVP===========>
***
*r* Regular RSVP router
***
<***> media flow
<==> segment of flow path protected by RSVP reservation
/\ SIP signaling
// control interface between the SIP Server/Proxy and
RSVP Proxy
Figure 15: CAC on Enterprise WAN Use Case
A.3. RSVP-based Voice CAC in Telephony Service Provider Core
Let us consider an environment involving a Telephony Service Provider
(TSP). Let us further assume that end-users are attached to the TSP
via Session Border Controllers (SBCs). The SBCs may be remotely
controlled by a SIP Server. The SIP Server may control establishment
Le Faucheur, et al. Expires March 15, 2008 [Page 35]
Internet-Draft RSVP Proxy Approaches September 2007
of RSVP reservations between the SBCs for admission control of
sessions over the core. This relies on the Application_Entity-
Controlled RSVP Proxy approach presented in Section 4.5. This is
illustrated in the Figure below.
Le Faucheur, et al. Expires March 15, 2008 [Page 36]
Internet-Draft RSVP Proxy Approaches September 2007
|---------|
//////////////| SIP |\\\\\\\\\\\\
/ | Server/ | \
/ | Proxy | \
/ |---------| \
/ // \\ \
/ // \\ \
/ // \\ \
/ // \\ \
/ // \\ \
|-----| |--------| *** *** |--------| |-----|
| IP |------| |---*r*---*r*---| |-------|IP |
|Phone| | SBC | *** *** | SBC | |Phone|
|-----| | + | | + | |-----|
| RSVP | | RSVP |
| Proxy | | Proxy |
|--------| |--------|
<---Access----> <---Access----->
<---------Core---------->
<*************> <***********************> <**************>
<=========RSVP==========>
***
*r* Regular RSVP router
***
<***> media flow
<==> segment of flow path protected by RSVP reservation
/\ SIP signaling
// control interface between the SIP Server/Proxy and
SBC/RSVP Proxy
Figure 16: Voice CAC in TSP Domain
A.4. RSVP Proxies for Mobile Access Networks
Mobile access networks are increasingly based on IP technology. This
implies that, on the network layer, all traffic, both traditional
data and streamed data like audio or video, is transmitted as
packets. Increasingly popular multimedia applications would benefit
Le Faucheur, et al. Expires March 15, 2008 [Page 37]
Internet-Draft RSVP Proxy Approaches September 2007
from better than best-effort service from the network, a forwarding
service with strict Quality of Service (QoS) with guaranteed minimum
bandwidth and bounded delay. Other applications, such as electronic
commerce, network control and management, and remote login
applications, would also benefit from a differentiated treatment.
The IETF has two main models for providing differentiated treatment
of packets in routers. The Integrated Services (IntServ) model
[RFC1633] together with the Resource Reservation Protocol (RSVP)
[RFC2205] [RFC2210] [RFC2961] provides per-flow guaranteed end-to-end
transmission service. The Differentiated Services (DiffServ)
framework [RFC2475] provides non- signaled flow differentiation that
usually provides, but does not guarantee, proper transmission
service.
However, these architectures have potential weaknesses for deployment
in Mobile Access Networks. For example, RSVP requires support from
both communication end points, and the protocol may have potential
performance issues in mobile environments. DiffServ can only provide
statistical guarantees and is not well suited for dynamic
environments.
Let us consider a scenario, where a fixed network correspondent node
(CN) would be sending a multimedia stream to an end host behind a
wireless link. If the correspondent node does not support RSVP it
cannot signal its traffic characteristics to the network and request
specific forwarding services. Likewise, if the correspondent node is
not able to mark its traffic with a proper DiffServ Code Point (DSCP)
to trigger service differentiation, the multimedia stream will get
only best-effort service which may result in poor visual and audio
quality in the receiving application. Even if the connecting wired
network is over-provisioned, an end host would still benefit from
local resource reservations, especially in wireless access networks,
where the bottleneck resource is most probably the wireless link.
RSVP proxies would be a very beneficial solution to this problem. It
would allow distinguishing local network reservations from the end-
to-end reservations. The end host does not need to know the access
network topology or the nodes that will reserve the local resources.
The access network would do resource reservations for both incoming
and outgoing flows based on certain criterion, e.g., filters based on
application protocols. Another option is that the mobile end host
makes an explicit reservation that identifies the intention and the
access network will find the correct local access network node(s) to
respond to the reservation. RSVP proxies would, thus, allow resource
reservation over the segment which is the most likely bottleneck, the
wireless connectivity. If the wireless access network uses a local
mobility management mechanism, where the IP address of the mobile
Le Faucheur, et al. Expires March 15, 2008 [Page 38]
Internet-Draft RSVP Proxy Approaches September 2007
node does not change during handover, RSVP reservations would follow
the mobile node movement.
A.5. RSVP Proxies for Reservations in the presence of IPsec Gateways
[I-D.ietf-tsvwg-vpn-signaled-preemption] discusses how resource
reservation can be supported end-to-end in a nested VPN environment.
At each VPN level, VPN Routers behave as [RFC4301] security gateways
between a plaintext domain and a cyphertext domain. To achieve end-
to-end resource reservation, the VPN Routers process RSVP signaling
on the plaintext side, perform aggregation of plaintext reservations,
and maintain the corresponding aggregate RSVP reservations on the
cyphertext side. Each aggregate reservation is established on behalf
of multiple encrypted end-to-end sessions sharing the same ingress
and egress VPN Routers. These aggregate reservations can be as
specified in [RFC3175] or [RFC4860].
Section 3 of [I-D.ietf-tsvwg-vpn-signaled-preemption] discusses the
necessary data flows within a VPN Router to achieve the behavior
described in the previous paragraph. Two mechanisms are described to
achieve such data flows. Section 3.1 presents the case where the VPN
Router carries data across the cryptographic boundary. Section 3.2
discusses the case where the VPN router uses a Network-Guard.
Where such mechanisms are not supported by the VPN Routers, the
approach for end-to-end reservation presented in
[I-D.ietf-tsvwg-vpn-signaled-preemption] cannot be deployed. An
alternative approach to support resource reservations within the
cyphertext core is to use the "Application_Entity-Controlled Proxy"
approach (as defined in Section 4.5) in the following way:
o the RSVP Proxies are located inside the cyphertext domain and use
aggregate RSVP reservations,
o the Application Entity exchange application level signaling with
the end systems in the plaintext domain,
o the Application Entity controls the RSVP Proxies in the cyphertext
domain via an RSVP Proxy control interface
This is illustrated in Figure 17 in the case where the application is
SIP-based multimedia communications.
Le Faucheur, et al. Expires March 15, 2008 [Page 39]
Internet-Draft RSVP Proxy Approaches September 2007
|-------| |-------|
|SIP |///////////////////\\\\\\\\\\\\\\\\\|SIP |
/|Server/| |Server/|\
/ |Proxy | |Proxy | \
/ |-------| |-------| \
/ ^ \\ // ^ \
/ ^ \\ // ^ \
/ ^ \\ // ^ \
|---| |------| |--------| *** *** |--------| |------| |---|
| S |---|IPsec |--| ARSVP |---*r*---*r*---| ARSVP |--|IPsec |---| R |
|---| | GW | | Sender | *** *** |Receiver| | GW | |---|
|------| | Proxy | | Proxy | |------|
|--------| |--------|
***PT*****> **********************CT****************> ****PT***>
=====> =====>
=====ARSVP======>
|----| RSVP-capable |----| RSVP-capable ***
| S | Sender | R | Receiver *r* regular RSVP
|----| |----| *** router
|------|
|IPsec | IPsec security gateway
| GW |
|------|
ARSVP Aggregate RSVP
***> media flow
==> segment of flow path protected by RSVP reservation
/ \ SIP signaling
^ Network management interface between SIP Server/Proxy
and IPsec security gateway
// control interface between SIP Server/Proxy and ARSVP Proxy
PT Plaintext network
CT Cyphertext network
Figure 17: RSVP Proxies for Reservations in the Presence of IPsec
Le Faucheur, et al. Expires March 15, 2008 [Page 40]
Internet-Draft RSVP Proxy Approaches September 2007
Gateways
Where the sender and receiver are RSVP capable, they may also use
RSVP signaling. This achieves resource reservation on the plaintext
segments of the end-to-end i.e. :
o from the sender to the ingress IPsec gateway and
o from the egress IPsec gateway to the receiver.
In this use case, because the VPN Routers do not support any RSVP
specific mechanism, the end-to-end RSVP signaling is effectively
hidden by the IPsec gateways on the cyphertext segment of the end-to-
end path.
As with the "Application_Entity-Controlled Proxy" approach (defined
in Section 4.5), the solution here for synchronizing RSVP signaling
with application-level signaling is to rely on an application-level
signaling device that controls an on-path RSVP Proxy function.
However, in the present use case, the RSVP Proxies are a component of
a cyphertext network where all user (bearer) traffic is IPsec
encrypted. This has a number of implications including the
following:
1. encrypted flows can not be identified in the cyphertext domain so
that network nodes can only classify traffic based on IP address
and DiffServ Code Points (DSCPs). As a result, only aggregate
RSVP reservations (such as those specified in [RFC3175] or
[RFC4860] ) can be used. This is similar to
[I-D.ietf-tsvwg-vpn-signaled-preemption].
2. Determining the RSVP Sender proxy and RSVP receiver Proxy to be
used for aggregation of a given flow from sender to receiver
creates a number of challenges. Details on how this may be
achieved are beyond the scope of this document. We observe that,
as illustrated in Figure 17, this may be facilitated by a network
management interface between the application entity and the IPsec
gateways. For example, this interface may be used by the
application entity to obtain information about which IPsec
gateway is on the path of a given end-to-end flow. Then, the
application entity may maintain awareness of which RSVP Proxy is
on the cyphertext path between a given pair of IPsec gateways.
How such awareness is achieved is beyond the scope of this
document. We simply observe that such awareness can be easily
achieved through simple configuration in the particular case
where a single (physical or logical) RSVP Proxy is fronting a
given IPsec gateway. We also observe that when awareness of the
RSVP Receiver Proxy for a particular egress IPsec gateway (or
Le Faucheur, et al. Expires March 15, 2008 [Page 41]
Internet-Draft RSVP Proxy Approaches September 2007
end-to-end flow) is not available, the aggregate reservation may
be signaled by the RSVP Sender Proxy to the destination address
of the egress IPsec gateway and then proxied by the RSVP Receiver
Proxy.
Different flavors of operations are possible in terms of aggregate
reservation sizing. For example, the application entity can initiate
an aggregate reservation of fixed size a priori and then simply keep
count of the bandwidth used by sessions and reject sessions that
would result in excess usage of an aggregate reservation. The
application entity could also re-size the aggregate reservations on a
session by session basis. Alternatively, the application entity
could re-size the aggregate reservations in step increments typically
corresponding to the bandwidth requirement of multiple sessions.
Authors' Addresses
Francois Le Faucheur
Cisco Systems
Greenside, 400 Avenue de Roumanille
Sophia Antipolis 06410
France
Phone: +33 4 97 23 26 19
Email: flefauch@cisco.com
Jukka Manner
University of Helsinki
P.O. Box 68
University of Helsinki FIN-00014 University of Helsinki
Finland
Phone: +358 9 191 51298
Email: jmanner@cs.helsinki.fi
URI: http://www.cs.helsinki.fi/u/jmanner/
Dan Wing
Cisco Systems
170 West Tasman Drive
San Jose, CA 95134
United States
Email: dwing@cisco.com
Le Faucheur, et al. Expires March 15, 2008 [Page 42]
Internet-Draft RSVP Proxy Approaches September 2007
Allan Guillou
Neuf Cegetel
40-42 Quai du Point du Jour
Boulogne-Billancourt, 92659
France
Email: allan.guillou@neufcegetel.fr
Le Faucheur, et al. Expires March 15, 2008 [Page 43]
Internet-Draft RSVP Proxy Approaches September 2007
Full Copyright Statement
Copyright (C) The IETF Trust (2007).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgment
Funding for the RFC Editor function is provided by the IETF
Administrative Support Activity (IASA).
Le Faucheur, et al. Expires March 15, 2008 [Page 44]
| PAFTECH AB 2003-2026 | 2026-04-22 05:59:32 |