One document matched: draft-ietf-tcpm-tcp-lcd-02.xml
<?xml version="1.0" encoding="US-ASCII"?>
<!-- This template is for creating an Internet Draft using xml2rfc,
which is available here: http://xml.resource.org. -->
<!DOCTYPE rfc SYSTEM "rfc2629.dtd" [
<!-- One method to get references from the online citation libraries.
There has to be one entity for each item to be referenced.
An alternate method (rfc include) is described in the references. -->
<!ENTITY rfc0791 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.0791.xml">
<!ENTITY rfc0792 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.0792.xml">
<!ENTITY rfc0793 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.0793.xml">
<!ENTITY rfc0826 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.0826.xml">
<!ENTITY rfc1122 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.1122.xml">
<!ENTITY rfc1323 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.1323.xml">
<!ENTITY rfc1812 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.1812.xml">
<!ENTITY rfc2003 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.2003.xml">
<!ENTITY rfc2119 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.2119.xml">
<!ENTITY rfc2460 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.2460.xml">
<!ENTITY rfc2629 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.2629.xml">
<!ENTITY rfc2784 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.2784.xml">
<!ENTITY rfc2988 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.2988.xml">
<!ENTITY rfc3522 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.3522.xml">
<!ENTITY rfc3168 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.3168.xml">
<!ENTITY rfc3782 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.3782.xml">
<!ENTITY rfc3819 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.3819.xml">
<!ENTITY rfc4015 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.4015.xml">
<!ENTITY rfc4301 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.4301.xml">
<!ENTITY rfc4443 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.4443.xml">
<!ENTITY rfc5461 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.5461.xml">
<!ENTITY rfc5681 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.5681.xml">
<!ENTITY rfc5682 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.5682.xml">
<!ENTITY rfc5927 SYSTEM "http://xml.resource.org/public/rfc/bibxml/reference.RFC.5927.xml">
<!ENTITY retransmit-now SYSTEM "http://xml.resource.org/public/rfc/bibxml3/reference.I-D.eggert-tcpm-tcp-retransmit-now.xml">
<!ENTITY tcp-rlci SYSTEM "http://xml.resource.org/public/rfc/bibxml3/reference.I-D.schuetz-tcpm-tcp-rlci.xml">
<!ENTITY linkup SYSTEM "http://xml.resource.org/public/rfc/bibxml3/reference.I-D.dawkins-trigtran-linkup.xml">
]>
<?xml-stylesheet type='text/xsl' href='rfc2629.xslt' ?>
<!-- used by XSLT processors -->
<!-- For a complete list and description of processing instructions (PIs),
please see http://xml.resource.org/authoring/README.html. -->
<!-- Below are generally applicable Processing Instructions (PIs) that most I-Ds
might want to use. (Here they are set differently than their defaults in
xml2rfc v1.32) -->
<?rfc strict="yes" ?>
<!-- give errors regarding ID-nits and DTD validation -->
<!-- control the table of contents (ToC) -->
<?rfc toc="yes"?>
<!-- generate a ToC -->
<?rfc tocdepth="3"?>
<!-- the number of levels of subsections in ToC. default: 3 -->
<!-- control references -->
<?rfc symrefs="yes"?>
<!-- use symbolic references tags, i.e, [RFC2119] instead of [1] -->
<?rfc sortrefs="yes" ?>
<!-- sort the reference entries alphabetically -->
<!-- control vertical white space
(using these PIs as follows is recommended by the RFC Editor) -->
<?rfc compact="yes" ?>
<!-- do not start each main section on a new page -->
<?rfc subcompact="no" ?>
<!-- keep one blank line between list items -->
<!-- end of list of popular I-D processing instructions -->
<rfc category="exp" docName="draft-ietf-tcpm-tcp-lcd-02" ipr="trust200902">
<!-- category values: std, bcp, info, exp, and historic
ipr values: full3667, noModification3667, noDerivatives3667
you can add the attributes updates="NNNN" and obsoletes="NNNN"
they will automatically be output with "(if approved)" -->
<!-- ***** FRONT MATTER ***** -->
<front>
<!-- The abbreviated title is used in the page header - it is only
necessary if the full title is longer than 39 characters -->
<title abbrev="Making TCP more Robust to LCDs">
Making TCP more Robust to Long Connectivity Disruptions (TCP-LCD)</title>
<!-- add 'role="editor"' below for the editors if appropriate -->
<author initials="A.Z."
surname="Zimmermann"
fullname="Alexander Zimmermann">
<organization>RWTH Aachen University</organization>
<address>
<postal>
<street>Ahornstrasse 55</street>
<city>Aachen</city>
<region></region>
<code>52074</code>
<country>Germany</country>
</postal>
<phone>+49 241 80 21422</phone>
<email>zimmermann@cs.rwth-aachen.de</email>
<!-- uri and facsimile elements may also be added -->
</address>
</author>
<author initials="A.H."
surname="Hannemann"
fullname="Arnd Hannemann">
<organization>RWTH Aachen University</organization>
<address>
<postal>
<street>Ahornstrasse 55</street>
<city>Aachen</city>
<region></region>
<code>52074</code>
<country>Germany</country>
</postal>
<phone>+49 241 80 21423</phone>
<email>hannemann@nets.rwth-aachen.de</email>
<!-- uri and facsimile elements may also be added -->
</address>
</author>
<date year="2010" />
<!-- If the month and year are both specified and are the current ones,
xml2rfc will fill in the current day for you. If only the current
year is specified, xml2rfc will fill in the current day and month
for you. If the year is not the current one, it is necessary to
specify at least a month (xml2rfc assumes day="1" if not specified
for the purpose of calculating the expiry date). With drafts it is
normally sufficient to specify just the year. -->
<!-- Meta-data Declarations -->
<area>General</area>
<workgroup>TCP Maintenance and Minor Extensions (TCPM) WG</workgroup>
<!-- WG name at the upperleft corner of the doc, IETF is fine for
individual submissions. If this element is not present, the default
is "Network Working Group", which is used by the RFC Editor as a
nod to the history of the IETF. -->
<keyword>Transmission Control Protocol (TCP),
Internet Control Message Protocol (ICMP), Long Connectivity
Disruption (LCD)</keyword>
<!-- Keywords will be incorporated into HTML output
files in a meta tag but they have no effect on text or nroff
output. If you submit your draft to the RFC Editor, the
keywords will be used for the search engine. -->
<abstract>
<t>Disruptions in end-to-end path connectivity, which last longer
than one retransmission timeout, cause suboptimal TCP performance.
The reason for this performance degradation is that TCP interprets
segment loss induced by long connectivity disruptions as a sign of
congestion, resulting in repeated retransmission timer backoffs.
This, in turn, leads to a delayed detection of the re-establishment
of the connection since TCP waits for the next retransmission
timeout before it attempts a retransmission.</t>
<t>This document proposes an algorithm to make TCP more
robust to long connectivity disruptions (TCP-LCD). It describes how
standard ICMP messages can be exploited during timeout-based loss
recovery to disambiguate true congestion loss from non-congestion
loss caused by connectivity disruptions. Moreover, a reversion
strategy of the retransmission timer is specified that enables a
more prompt detection of whether or not the connectivity to a
previously disconnected peer node has been restored. TCP-LCD is a
TCP sender-only modification that effectively improves TCP
performance in case of connectivity disruptions.</t>
</abstract>
</front>
<!-- ***** MAIN MATTER ***** -->
<middle>
<!-- ***** Section: Terminology ***** -->
<section anchor="terminology" title="Terminology">
<t>The key words "MUST", "MUST NOT", "REQUIRED", "SHALL",
"SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
<xref target="RFC2119" />.</t>
<t>The reader should be familiar with the algorithm and terminology
from <xref target='RFC2988' />, which defines the standard
algorithm Transmission Control Protocol (TCP) senders are required
to use to compute and manage their retransmission timer. In this
document, the terms "retransmission timer" and "retransmission
timeout" are used as defined in <xref target='RFC2988' />. The
retransmission timer ensures data delivery in the absence of any
feedback from the receiver. The duration of this timer is referred
to as retransmission timeout (RTO).</t>
<t>As defined in <xref target='RFC0793' />, the term "acceptable
acknowledgment (ACK)" refers to a TCP segment that acknowledges
previously unacknowledged data. The TCP sender state variable
"SND.UNA" and the current segment variable "SEG.SEQ" are used as
defined in <xref target='RFC0793' />. SND.UNA holds the segment
sequence number of earliest segment that has not been acknowledged
by the TCP receiver (the oldest outstanding segment). SEG.SEQ is
the segment sequence number of a given segment.</t>
<t>For the purposes of this specification, we define the term
"timeout-based loss recovery" that refers to the state that a TCP
sender enters upon the first timeout of the oldest outstanding
segment (SND.UNA) and leaves upon the arrival of the *first*
acceptable ACK. It is important to note that other documents use a
different interpretation of the term "timeout-based loss recovery".
For example, the NewReno modification to TCP's Fast Recovery
algorithm <xref target='RFC3782' /> extents the period a TCP sender
remains in timeout-based loss recovery compared to the one defined
in this document. This is because <xref target='RFC3782' />
attempts to avoid unnecessary multiple Fast Retransmits that can
occur after an RTO.</t>
</section>
<!-- ***** Section: Introduction ***** -->
<section anchor="intro" title="Introduction">
<t>Connectivity disruptions can occur in many different situations.
The frequency of connectivity disruptions depends on the properties
of the end-to-end path between the communicating hosts. While
connectivity disruptions can occur in traditional wired networks,
e.g., caused by an unplugged network cable, the likelihood of
their occurrence is significantly higher in wireless (multi-hop)
networks. Especially, end-host mobility, network topology changes,
and wireless interferences are crucial factors. In the case of the
Transmission Control Protocol (TCP) <xref target='RFC0793' />, the
performance of the connection can experience a significant
reduction compared to a permanently connected path
<xref target='SESB05' />. This is because TCP, which was originally
designed to operate in fixed and wired networks, generally assumes
that the end-to-end path connectivity is relatively stable over the
connection's lifetime.</t>
<t>Depending on their duration, connectivity disruptions can be
classified into two groups
<xref target='I-D.schuetz-tcpm-tcp-rlci' />: "short" and "long". A
connectivity disruption is "short" if connectivity returns before
the retransmission timer fires for the first time. In this case,
TCP recovers lost data segments through Fast Retransmit and lost
acknowledgments (ACK) through successfully delivered later ACKs.
Connectivity disruptions are declared as "long" for a given TCP
connection if the retransmission timer fires at least once before
connectivity is resumed. Whether or not path characteristics, like
the round trip time (RTT) or the available bandwidth, have changed
when connectivity resumes after a disruption is another important
aspect for TCP's retransmission scheme
<xref target='I-D.schuetz-tcpm-tcp-rlci'/>.</t>
<t>This document improves TCP's behavior in case of "long
connectivity disruptions". In particular, it focuses on the period
prior to the re-establishment of the connectivity to a previously
disconnected peer node. The document does not describe any
modifications to TCP's behavior and its congestion control
mechanisms <xref target='RFC5681' /> after connectivity has been
restored.</t>
<t>When a long connectivity disruption occurs on a TCP connection,
the TCP sender eventually does not receive any more
acknowledgments. After the retransmission timer expires, the TCP
sender enters the timeout-based loss recovery and declares the
oldest outstanding segment (SND.UNA) as lost. Since TCP tightly
couples reliability and congestion control, the retransmission of
SND.UNA is triggered together with the reduction of the
transmission rate. This is based on the assumption that segment
loss is an indication of congestion <xref target='RFC5681' />. As
long as the connectivity disruption persists, TCP will repeat this
procedure until the oldest outstanding segment has successfully
been acknowledged, or until the connection has timed out. TCP
implementations that follow the recommended retransmission timeout
(RTO) management of <xref target='RFC2988'> RFC 2988</xref>
double the RTO after each retransmission attempt. However, the
RTO growth may be bounded by an upper limit, the maximum RTO,
which is at least 60s, but may be longer: Linux, for example, uses
120s. If connectivity is restored between two retransmission
attempts, TCP still has to wait until the retransmission timer
expires before resuming transmission, since it simply does not have
any means to know if the connectivity has been re-established.
Therefore, depending on when connectivity becomes available again,
this can waste up to a maximum RTO of possible transmission
time.</t>
<t>This retransmission behavior is not efficient, especially in
scenarios with long connectivity disruptions. In the ideal case,
TCP would attempt a retransmission as soon as connectivity to its
peer has been re-established. In this document, we specify a TCP
sender-only modification to provide robustness to long connectivity
disruptions (TCP-LCD). The memo describes how the standard Internet
Control Message Protocol (ICMP) can be exploited during
timeout-based loss recovery to identify non-congestion loss caused
by long connectivity disruptions. TCP-LCD's reversion strategy of
the retransmission timer enables higher-frequency retransmissions
and thereby a prompt detection when connectivity to a previously
disconnected peer node has been restored. If no congestion is
present, TCP-LCD approaches the ideal behavior.</t>
</section>
<!-- ***** Section: Connectivity Disruption Indication ***** -->
<section anchor="cdi" title="Connectivity Disruption Indication">
<t>If the queue of an intermediate router that is experiencing a link
outage can buffer all incoming packets, a connectivity disruption
will only cause a variation in delay, which is handled well by TCP
implementations using either Eifel <xref target='RFC3522' />,
<xref target='RFC4015' /> or Forward RTO-Recovery (F-RTO)
<xref target='RFC5682' />. However, if the link outage lasts for
too long, the router experiencing the link outage is forced to drop
packets, and finally to discard the according route. Means to
detect such link outages include reacting on failed address
resolution protocol (ARP) <xref target='RFC0826' /> queries,
unsuccessful link sensing, and the like. However, this is solely in
the responsibility of the respective router.
<list style="empty">
<t>Note: The focus of this memo is on introducing a method
how ICMP messages may be exploited to improve TCP's
performance; how different physical and link layer
mechanisms below the network layer may trigger ICMP
destination unreachable messages are out of scope of this
memo.</t>
</list>
</t>
<t>Provided that no other route to the specific destination exists,
the router will notify the corresponding sending host about the
dropped packets via ICMP destination unreachable messages of code 0
(net unreachable) or code 1 (host unreachable)
<xref target='RFC1812' />. Therefore, the sending host can use the
ICMP destination unreachable messages of these codes as an
indication for a connectivity disruption, since the reception of
these messages provide evidence that packets were dropped due to a
link outage.</t>
<t>Note that there are also other ICMP destination unreachable
messages with different codes. Some of them are candidates for
connectivity disruption indications, too, but need further
investigation. For example, ICMP destination unreachable messages
with code 5 (source route failed), code 11 (net unreachable for
TOS), or code 12 (host unreachable for TOS)
<xref target='RFC1812' />. On the other hand, codes that flag hard
errors are of no use for this scheme, since TCP should
abort the connection when those are received
<xref target='RFC1122' />. In the following, the term "ICMP
unreachable message" is used as synonym for ICMP destination
unreachable messages of code 0 or code 1.</t>
<t>The accurate interpretation of ICMP unreachable messages as a
connectivity disruption indication is complicated by the following
two peculiarities of ICMP messages. First, they do not
necessarily operate on the same timescale as the packets, i.e., TCP
segments that elicited them. When a router drops a packet due to a
missing route, it will not necessarily send an ICMP unreachable
message immediately, but will rather queue it for later delivery.
Second, ICMP messages are subject to rate limiting, e.g., when a
router drops a whole window of data due to a link outage, it is
unlikely to send as many ICMP unreachable messages as dropped TCP
segments. Depending on the load of the router, it may not even send
any ICMP unreachable messages at all. Both peculiarities originate
from <xref target='RFC1812' />.</t>
<t>Fortunately, according to <xref target='RFC0792' />, ICMP
unreachable messages have to contain in their body the entire
Internet Protocol (IP) header <xref target='RFC0791' /> of the
datagram eliciting the ICMP unreachable message, plus the first 64
bits of the payload of that datagram. This allows the sending host
to match the ICMP error message to the transport connection that
elicited it. <xref target='RFC1812'>RFC 1812</xref> augments these
requirements and states that ICMP messages should contain as much
of the original datagram as possible without the length of the ICMP
datagram exceeding 576 bytes. Therefore, in case of TCP, at least
the source port number, the destination port number, and the 32-bit
TCP sequence number are included. This allows the originating TCP
to demultiplex the received ICMP message and to identify the affected
connection. Moreover, it can identify which segment of the
respective connection triggered the ICMP unreachable message,
unless there are several segments in-flight with the same sequence
number (see <xref target='discuss_retrans_ambiguity' />).</t>
<t>A connectivity disruption indication in form of an ICMP
unreachable message associated with a presumably lost TCP segment
provides strong evidence that the segment was not dropped due to
congestion, but was successfully delivered as far as the reporting
router. It therefore did not witness any congestion at least on
that part of the path that was traversed by both the TCP segment
eliciting the ICMP unreachable message as well as the ICMP
unreachable message itself.</t>
</section>
<!-- ***** Section: Connectivity Disruption Reaction ***** -->
<section anchor="cdr" title="Connectivity Disruption Reaction">
<t><xref target='alg_idea' /> introduces the basic idea of TCP-LCD. The
complete algorithm is specified in <xref target='alg' />.</t>
<!-- ***** Subsection: Basic Idea ***** -->
<section anchor="alg_idea" title="Basic Idea">
<t>The goal of the algorithm is to promptly detect when
connectivity to a previously disconnected peer node has been
restored after a long connectivity disruption, while retaining
appropriate behavior in case of congestion. TCP-LCD exploits
standard ICMP unreachable messages during timeout-based loss
recovery. This increases TCP's retransmission frequency by
undoing one retransmission timer backoff whenever an ICMP
unreachable message is received that contains a segment with
a sequence number of a presumably lost retransmission.</t>
<t>This approach has the advantage of appropriately reducing the
probing rate in case of congestion. If either the
retransmission itself or the corresponding ICMP message is
dropped the previously performed retransmission timer backoff
is not undone, which effectively halves the probing rate.</t>
</section>
<!-- ***** Subsection: Algorithm Details ***** -->
<section anchor="alg" title="Algorithm Details">
<t>A TCP sender that uses <xref target='RFC2988'>
RFC 2988</xref> to compute TCP's retransmission timer MAY
employ the following scheme to avoid over-conservative
retransmission timer backoffs in case of long connectivity
disruptions. If a TCP sender does implement the following
steps, the algorithm MUST be initiated upon the first timeout
of the oldest outstanding segment (SND.UNA) and MUST be stopped
upon the arrival of the first acceptable ACK. The algorithm
MUST NOT be re-initiated upon subsequent timeouts for the same
segment. The scheme SHOULD NOT be used in SYN-SENT or
SYN-RECEIVED states <xref target='RFC0793' /> (see
<xref target="discuss_syn" />).</t>
<t>A TCP sender that does not employ
<xref target='RFC2988'>RFC 2988</xref> to compute TCP's
retransmission timer MUST NOT use TCP-LCD. We envision that
the scheme could be easily adapted to algorithms others than
RFC 2988. However, we leave this as future work.</t>
<t>In rule (2.5), <xref target='RFC2988'>RFC 2988</xref>
provides the option to place a maximum value on the RTO. When a
TCP implements this rule to provide an upper bound for the RTO,
it MUST also be used in the following algorithm. In
particular, if the RTO is bounded by an upper limit (maximum
RTO), the "MAX_RTO" variable used in this scheme MUST be
initialized with this upper limit. Otherwise, if the RTO is
unbounded, the "MAX_RTO" variable MUST be set to
infinity.</t>
<t>The scheme specified in this document uses the "BACKOFF_CNT"
variable, whose initial value is zero. The variable is used to
count the number of performed retransmission timer backoffs
during one timeout-based loss recovery. Moreover, the
"RTO_BASE" variable is used to recover the previous RTO if the
retransmission timer backoff was unnecessary. The variable is
initialized with the RTO upon initiation of timeout-based loss
recovery.</t>
<t>
<list style='format (%d)' counter="cnt">
<t>Before TCP updates the variable "RTO" when it
initiates timeout-based loss recovery, set the variables
"BACKOFF_CNT" and "RTO_BASE" as follows:
<list style='empty'>
<t>BACKOFF_CNT := 0;</t>
<?rfc subcompact='yes' ?>
<t>RTO_BASE := RTO.</t>
<?rfc subcompact='no' ?>
</list>
Proceed to step (R).</t>
</list>
<list style='hanging' hangIndent='5'>
<t hangText="(R)">This is a placeholder for standard TCP's
behavior in case the retransmission timer has expired.
In particular, if
<xref target='RFC2988'>RFC 2988</xref> is used,
steps (5.4) - (5.6) of that algorithm go here. Proceed
to step (2).</t>
</list>
<list style='format (%d)' counter="cnt">
<t>To account for the expiration of the retransmission
timer in the previous step (R), increment the
"BACKOFF_CNT" variable by one:
<list style='empty'>
<t>BACKOFF_CNT := BACKOFF_CNT + 1.</t>
</list>
</t>
<t>Wait either
<list style='empty'>
<t>for the expiration of the retransmission
timer. When the retransmission timer expires,
proceed to step (R);</t>
<t>or for the arrival of an acceptable ACK. When
an acceptable ACK arrives, proceed to step (A);
</t>
<t>or for the arrival of an ICMP unreachable
message. When the ICMP unreachable message
"ICMP_DU" arrives, proceed to step (4).</t>
</list>
</t>
</list>
<list style='format (%d)' counter="cnt">
<t>If "BACKOFF_CNT > 0", i.e., if at least one
retransmission timer backoff can be undone, then
<list style='empty'>
<t>proceed to step (5);</t>
</list>
else
<list style='empty'>
<t>proceed to step (3).</t>
</list>
</t>
<t>Extract the TCP segment header included in the ICMP
unreachable message "ICMP_DU":
<list style='empty'>
<t>SEG := Extract(ICMP_DU).</t>
</list>
</t>
<t>If "SEG.SEQ == SND.UNA", i.e., if the TCP segment
"SEG" eliciting the ICMP unreachable message "ICMP_DU"
contains the sequence number of a retransmission, then
<list style='empty'>
<t>proceed to step (7);</t>
</list>
else
<list style='empty'>
<t>proceed to step (3).</t>
</list>
</t>
<t>Undo the last retransmission timer backoff:
<list style='empty'>
<t>BACKOFF_CNT := BACKOFF_CNT - 1;</t>
<?rfc subcompact='yes' ?>
<t>RTO := min(RTO_BASE * 2^(BACKOFF_CNT), MAX_RTO).</t>
<?rfc subcompact='no' ?>
</list>
</t>
<t>If the retransmission timer expires due to the undoing
in the previous step (7), then
<list style='empty'>
<t>proceed to step (R);</t>
</list>
else
<list style='empty'>
<t>proceed to step (3).</t>
</list>
</t>
</list>
<list style='hanging' hangIndent='5'>
<t hangText="(A)">This is a placeholder for standard
TCP's behavior in case an acceptable ACK has arrived.
No further processing.</t>
</list>
</t>
<t>When a TCP in steady-state detects a segment loss using the
retransmission timer, it enters the timeout-based loss recovery
and initiates the algorithm (step 1). It adjusts the slow start
threshold (ssthresh), sets the congestion window (CWND) to one
segment, backs off the retransmission timer, and retransmits
the first unacknowledged segment (step R)
<xref target='RFC5681' />, <xref target='RFC2988' />. To account
for the expiration of the retransmission timer, the TCP sender
increments the "BACKOFF_CNT" variable by one (step 2).</t>
<t>In case the retransmission timer expires again (step 3a), a
TCP will repeat the retransmission of the first unacknowledged
segment and back off the retransmission timer once more (step
R) <xref target='RFC2988' />, as well as increment the
"BACKOFF_CNT" variable by one (step 2). Note that a TCP may
implement <xref target='RFC2988'>RFC 2988's</xref> option
to place a maximum value on the RTO that may result in not
performing the retransmission timer backoff. However, step (2)
MUST always and unconditionally be applied, no matter whether
or not the retransmission timer is actually backed off. In
other words, each time the retransmission timer expires, the
"BACKOFF_CNT" variable MUST be incremented by one.</t>
<t>If the first received packet after the retransmission(s) is
an acceptable ACK (step 3b), a TCP will proceed as normal,
i.e., slow start the connection and terminate the algorithm
(step A). Later ICMP unreachable messages from the just
terminated timeout-based loss recovery are ignored, since the
ACK clock is already restarting due to the successful
retransmission.</t>
<t>On the other hand, if the first received packet after the
retransmission(s) is an ICMP unreachable message (step 3c), and
if step (4) permits it, TCP SHOULD undo one backoff for each
ICMP unreachable message reporting an error on a
retransmission. To decide if an ICMP unreachable message was
elicited by a retransmission, the sequence number it contains
is inspected (step 5, step 6). The undo is performed by
re-calculating the RTO with the decremented "BACKOFF_CNT"
variable (step 7). This calculation explicitly matches the
(bounded) exponential backoff specified in rule (5.5) of
<xref target='RFC2988' />.</t>
<t>Upon receipt of an ICMP unreachable message that legitimately
undoes one backoff, there is the possibility that the shortened
retransmission timer has already expired (step 8). Then, TCP
SHOULD retransmit immediately. In case the shortened
retransmission timer has not yet expired, TCP MUST wait
accordingly.</t>
</section>
</section>
<!-- ***** Section: Discussion of TCP-LCD ***** -->
<section anchor="discussion" title="Discussion of TCP-LCD">
<t>TCP-LCD takes caution to only react to connectivity disruption
indications in the form of ICMP unreachable messages during
timeout-based loss recovery. Therefore, TCP's behavior is not
altered when either no ICMP unreachable messages are received, or
the retransmission timer of the TCP sender did not expire since the
last received acceptable ACK. Thus, by defintion, the algorithm
triggers only in the case of long connectivity disruptions.</t>
<t>Only such ICMP unreachable messages that contain a TCP segment
with a the sequence number of a retransmission, i.e., contain
SND.UNA, are evaluated by TCP-LCD. All other ICMP unreachable
messages are ignored. The arrival of those ICMP unreachable
messages provides strong evidence that the retransmissions were not
dropped due to congestion, but were successfully delivered to the
reporting router. In other words, there is no evidence for any
congestion at least on that very part of the path that was
traversed by both the TCP segment eliciting the ICMP unreachable
message as well as the ICMP unreachable message itself.</t>
<t>However, there are some situations where TCP-LCD makes a false
decision and incorrectly undoes a retransmission timer backoff. This
can happen, even when the received ICMP unreachable message contains
the segment number of a retransmission (SND.UNA), because the TCP
segment that elicited the ICMP unreachable message may either not
be a retransmission (<xref target='discuss_retrans_ambiguity' />),
or does not belong to the current timeout-based loss recovery
(<xref target='discuss_wrap_sequence_numbers' />). Finally, packet
duplication (<xref target='discuss_packet_dup' />) can also
spuriously trigger the algorithm.</t>
<t><xref target='discuss_probing_frequency' /> discusses possible
probing frequencies, while <xref target='discuss_steady-state' />
describes the motivation for not reacting to ICMP unreachable
messages while TCP is in steady-state.</t>
<!-- ***** Subsection: Retransmission Ambiguity ***** -->
<section anchor="discuss_retrans_ambiguity" title="Retransmission Ambiguity">
<t>Historically, the retransmission ambiguity problem
<xref target='Zh86' />, <xref target='KP87' /> is the TCP sender's
inability to distinguish whether the first acceptable ACK after
a retransmission refers to the original transmission or to the
retransmission. This problem occurs after both a Fast
Retransmit and a timeout-based retransmit. However, modern TCP
implementations can eliminate the retransmission ambiguity with
either the help of Eifel <xref target='RFC3522' />,
<xref target='RFC4015' /> or Forward RTO-Recovery (F-RTO)
<xref target='RFC5682' />.</t>
<t>The reversion strategy of the given algorithm suffers from a
form of retransmission ambiguity, too. In contrast to the above
case, TCP suffers from ambiguity regarding ICMP unreachable
messages received during timeout-based loss recovery. With the
TCP segment number included in the ICMP unreachable message, a
TCP sender is not able to determine if the ICMP unreachable
message refers to the original transmission or to any of the
timeout-based retransmissions. That is, there is an ambiguity
with regards to which TCP segment an ICMP unreachable message
reports on.</t>
<t>However, this ambiguity is not considered to be a problem
for the algorithm. The assumption that a received ICMP message
provides evidence that a non-congestion loss caused by the
connectivity disruption was wrongly considered a congestion
loss still holds, regardless to which TCP segment, transmission
or retransmission, the message refers.</t>
</section>
<!-- ***** Subsection: Wrapped Sequence Numbers ***** -->
<section anchor="discuss_wrap_sequence_numbers" title="Wrapped Sequence Numbers">
<t>Besides the ambiguity whether a received ICMP unreachable
message refers to the original transmission or to any of the
retransmissions, there is another source of ambiguity related
to the TCP sequence numbers contained in ICMP unreachable
messages. For high bandwidth paths, the sequence space may wrap
quickly. This migth cause that delayed ICMP unreachable
messages may coincidentally fit as valid input in the proposed
scheme. As a result, the scheme may incorrectly undo
retransmission timer backoffs. Chances for this to happen are
minuscule, since a particular ICMP message would need to
contain the exact sequence number of the current
oldest outstanding segment (SND.UNA), while at the same time
TCP is in timeout-based loss recovery. However, two "worst
case" scenarios for the algorithm are possible:</t>
<t>For instance, consider a steady state TCP connection, which
will be disrupted at an intermediate router R due to a link
outage. Upon the expiration of the RTO, the TCP sender enters
the timeout-based loss recovery and starts to retransmit the
earliest segment that has not been acknowledged (SND.UNA). For
some reason, router R delays all corresponding ICMP unreachable
messages so that the TCP sender backs the retransmission timer
off normally without any undoing. At the end of the
connectivity disruption, the TCP sender eventually detects the
re-establishment, leaves the scheme and finally the
timeout-based loss recovery, too. A sequence number wrap-around
later, the connectivity between the two peers is disrupted
again, but this time due to congestion and exactly at the time
at which the current SND.UNA matches the SND.UNA from the
previous cycle. If router R emits the delayed ICMP unreachable
messages now, the TCP sender would incorrectly undo
retransmission timer backoffs. As the TCP sequence number
contains 32 bits, the probability of this scenario is at most
1/2^32. Given sufficiently many retransmissions in the first
timeout-based loss recovery, the corresponding ICMP unreachable
messages could reduce the RTO in the second recovery at most to
"RTO_BASE". However, once the ICMP unreachable messages are
depleted, the standard exponential backoff will be performed.
Thus, the congestion response will only be delayed by some
false retransmissions.</t>
<t>Similar to the above, consider the case where a steady state
TCP connection with n segments in flight will be disrupted at
some point due to a link outage at an intermediate router R.
For each segment in flight, router R may generate an ICMP
unreachable message. However, due to some reason it delays
them. Once the link outage is over and the connection has been
re-established, the TCP sender leaves the scheme and
slow-starts the connection. Following a sequence number
wrap-around, a retransmission timeout occurs, just at the
moment the TCP sender's current window of data reaches the
previous range of the sequence number space again. In case
router R emits the delayed ICMP unreachable messages now,
spurious undoing of the retransmission timer backoff is
possible once, if the TCP segment number contained in ICMP
unreachable messages matches the current SND.UNA, and the
timeout was a result of congestion. In the case of another
connectivity disruption, the additional undoing of the
retransmission timer backoff has no impact. The probability of
this scenario is at most n/2^32.</t>
</section>
<!-- ***** Subsection: Packet Duplication ***** -->
<section anchor="discuss_packet_dup" title="Packet Duplication">
<t>In case an intermediate router duplicates packets, a TCP
sender may receive more ICMP unreachable messages during
timeout-based loss recovery than sent timeout-based
retransmissions. However, since TCP-LCD keeps track of the
number of performed retransmission timer backoffs in the
"BACKOFF_CNT" variable, it will not undo more retransmission
timer backoffs than were actually performed. Nevertheless, if
packet duplication and congestion coincide on the path between
the two communicating hosts, duplicated ICMP messages could
hide the congestion loss of some retransmissions or ICMP
messages, and the algorithm may incorrectly undo retransmission
timer backoffs. Considering the overall impact of a router that
duplicates packets, the additional load induced by some
spurious timeout-based retransmits can probably be
neglected.</t>
</section>
<!-- ***** Subsection: Probing frequency ***** -->
<section anchor="discuss_probing_frequency" title="Probing Frequency">
<t>One could argue that if an ICMP unreachable message arrives
for a timeout-based retransmission, the RTO shall be reset or
recalculated, similar to what is done when an ACK arrives
during timeout-based loss recovery (see Karn's algorithm
<xref target='KP87' />, <xref target="RFC2988" />), and a new
retransmission should be sent immediately. Generally, this
would allow for a much higher probing frequency based on the
round trip time up to the router where connectivity has been
disrupted. However, we believe the current scheme provides a
good trade-off between conservative behavior and fast detection
of connectivity re-establishment.</t>
</section>
<!-- ***** Subsection: Reaction during Connection Establishment -->
<section anchor="discuss_syn" title="Reaction during Connection Establishment">
<t>It is possible that a TCP sender enters timeout-based loss
recovery while the connection is in SYN-SENT or SYN-RECEIVED
states <xref target='RFC0793' />. The algorithm described in
this document could also be used for faster connection
establishment in networks with connectivity disruptions.
However, because existing TCP implementations
<xref target='RFC5461' /> already interpret ICMP unreachable
messages during connection establishment and abort the
corresponding connection, we refrain from suggesting this.</t>
</section>
<!-- ***** Subsection: Reaction in Steady-State ***** -->
<section anchor="discuss_steady-state" title="Reaction in Steady-State">
<t>Another exploitation of ICMP unreachable messages in the
context of TCP congestion control might seem appropriate in
case the ICMP unreachable message is received while TCP is in
steady-state, and the message refers to a segment from within
the current window of data. As the RTT up to the router that
generated the ICMP unreachable message is likely to be
substantially shorter than the overall RTT to the destination,
the ICMP unreachable message may very well reach the
originating TCP while it is transmitting the current window of
data. In case the remaining window is large, it might seem
appropriate to refrain from transmitting the remaining window
as there is timely evidence that it will only trigger further
ICMP unreachable messages at the very router. Although this
promises improvement from a wastage perspective, it may be
counterproductive from a security perspective. An attacker
could forge such ICMP messages, thereby forcing the originating
TCP to stop sending data, very similar to the blind
throughput-reduction attack mentioned in
<xref target="RFC5927" />.</t>
<t>An additional consideration is the following: in the presence
of multi-path routing, even the receipt of a legitimate ICMP
unreachable message cannot be exploited accurately, because
there is the possibility that only one of the multiple paths to the
destination is suffering from a connectivity disruption, which
causes ICMP unreachable messages to be sent. Then, however,
there is the possibility that the path along which the
connectivity disruption occurred contributed considerably to
the overall bandwidth, such that a congestion response is very
well reasonable. However, this is not necessarily the case.
Therefore, a TCP has no means except for its inherent
congestion control to decide on this matter. All in all, it
seems that for a connection in steady-state, i.e., not in
timeout-based loss recovery, reacting on ICMP unreachable
messages in regard to congestion control is not appropriate.
For the case of timeout-based retransmissions, however, there
is a reasonable congestion response, which is skipping further
retransmission timer backoffs because there is no congestion
indication - as described above.</t>
</section>
</section>
<!-- ***** Section: Dissolving Ambiguity Issues using the TCP Timestamps Option ***** -->
<section anchor="algo_save" title="Dissolving Ambiguity Issues using the TCP Timestamps Option">
<t>If the TCP Timestamps option <xref target='RFC1323' />
is enabled for a connection, a TCP sender SHOULD use the following
algorithm to dissolve the ambiguity issues mentioned in Sections
<xref target='discuss_retrans_ambiguity' format='counter' />,
<xref target='discuss_wrap_sequence_numbers' format='counter' />,
and <xref target='discuss_packet_dup' format='counter' />. In
particular, both the retransmission ambiguity and the packet
duplication problems are prevented by the following TCP-LCD
variant. On the other hand, the false positives caused by wrapped
sequence numbers cannot be completely avoided, but the likelihood
is further reduced by a factor of 1/2^32 since the Timestamp Value
field (TSval) of the TCP Timestamps Option contains 32 bits.</t>
<t>Hence, implementers may choose to implement the TCP-LCD with the
following modifications.</t>
<t>Step (1) is replaced by step (1'):
<list style="format (%d')" counter="cnt2">
<t>Before TCP updates the variable "RTO" when it initiates
timeout-based loss recovery, set the variables "BACKOFF_CNT"
and "RTO_BASE" and the data structure "RETRANS_TS" as follows:
<list style='empty'>
<t>BACKOFF_CNT := 0;</t>
<?rfc subcompact='yes' ?>
<t>RTO_BASE := RTO;</t>
<t>RETRANS_TS := [].</t>
<?rfc subcompact='no' ?>
</list>
Proceed to step (R).</t>
</list>
</t>
<t>Step (2) is extended by step (2b):
<list style="format (%db)" counter="cnt2">
<t>Store the value of the Timestamp Value field (TSval) of
the TCP Timestamps option included in the retransmission
"RET" sent in step (R) into the "RETRANS_TS" data structure:
<list style='empty'>
<t>RETRANS_TS.add(RET.TSval)</t>
</list>
</t>
</list>
</t>
<t>Step (6) is replaced by step (6'):
<list style='hanging' hangIndent='6'>
<t hangText="(6')"> If "SEG.SEQ == SND.UNA &&
RETRANS_TS.exists(SEQ.TSval)", i.e., if the TCP segment
"SEG" eliciting the ICMP unreachable message "ICMP_DU"
contains the sequence number of a retransmission, and the
value in its Timestamp Value field (TSval) is valid, then
<list style='empty'>
<t>proceed to step (7');</t>
</list>
else
<list style='empty'>
<t>proceed to step (3).</t>
</list>
</t>
</list>
</t>
<t>Step (7) is replaced by step (7'):
<list style='hanging' hangIndent='6'>
<t hangText="(7')">Undo the last retransmission timer backoff:
<list style='empty'>
<t>RETRANS_TS.remove(SEQ.TSval);</t>
<?rfc subcompact='yes' ?>
<t>BACKOFF_CNT := BACKOFF_CNT - 1;</t>
<t>RTO := min(RTO_BASE * 2^(BACKOFF_CNT), MAX_RTO).</t>
<?rfc subcompact='no' ?>
</list>
</t>
</list>
</t>
<t>The downside of the this variant is twofold. First, the
modifications come at a cost: the TCP sender is required to store
the timestamps of all retransmissions sent during one timeout-based
loss recovery. Second, this variant can only undo a retransmission
timer backoff if the intermediate router experiencing the link
outage implements <xref target='RFC1812' /> and chooses to include
as many more than the first 64 bits of the payload of the
triggering datagram, as are needed to include the TCP Timestamps
option in the ICMP unreachable message.</t>
</section>
<!-- ***** Section: Interoperability Issues ***** -->
<section anchor="interoperability" title="Interoperability Issues">
<t>This section discusses interoperability issues related to
introducing TCP-LCD.</t>
<!-- ***** Subsection: TCP Connection Failures ***** -->
<section anchor="interaction_rfc1122" title="Detection of TCP Connection Failures">
<t>TCP-LCD may have side-effects on TCP implementations that
attempt to detect TCP connection failures by counting
timeout-based retransmissions. <xref target='RFC1122' />
states in Section 4.2.3.5 that a TCP host must handle excessive
retransmissions of data segments with two thresholds R1 and R2
that measure the number of retransmissions that have occurred for
the same segment. Both thresholds might either be measured in
time units or as a count of retransmissions.</t>
<t>Due to TCP-LCD's reversion strategy of the retransmission
timer, the assumption that a certain number of retransmissions
corresponds to a specific time interval no longer holds, as
additional retransmissions may be performed during
timeout-based-loss recovery to detect the end of the
connectivity disruption. Therefore, a TCP employing TCP-LCD
either MUST measure the thresholds R1 and R2 in time units
or, in case R1 and R2 are counters of retransmissions, MUST
convert them into time intervals, which correspond to the time
an unmodified TCP would need to reach the specified number of
retransmissions.</t>
</section>
<!-- ***** Subsection: Explicit Congestion Notification ***** -->
<section anchor="interaction_ecn" title="Explicit Congestion Notification">
<t>With Explicit Congestion Notification (ECN)
<xref target='RFC3168' />, ECN-capable routers are no longer
limited to dropping packets to indicate congestion. Instead,
they can set the Congestion Experienced (CE) codepoint in the
IP header to indicate congestion. With TCP-LCD, it may happen
that during a connectivity disruption, a received ICMP
unreachable message has been elicited by a timeout-based
retransmission that was marked with the CE codepoint before
reaching the router experiencing the link outage. In such a
case, a TCP sender MUST, corresponding to
<xref target='RFC3168' /> (Section 6.1.2), additionally reset
the retransmission timer in case the algorithm undoes a
retransmission timer backoff.</t>
</section>
<!-- ***** Subsection: ICMP for IP version 6 ***** -->
<section anchor="interaction_icmpv6" title="ICMP for IP version 6">
<t><xref target='RFC4443'>RFC 4443</xref> specifies the
Internet Control Message Protocol (ICMPv6) to be used with the
Internet Protocol version 6 (IPv6) <xref target='RFC2460' />.
From TCP-LCD's point of view, it is important to notice that
for IPv6, the payload of an ICMPv6 error messages has to
include as many bytes as possible from the IPv6 datagram that
elicited the ICMPv6 error message, without making the error
message exceed the minimum IPv6 MTU (1280 bytes)
<xref target='RFC4443' />. Thus, more information is available
for TCP-LCD than in the case of IPv4.</t>
<t>The counterpart of the ICMPv4 destination unreachable
message of code 0 (net unreachable) and of code 1 (host
unreachable) is the ICMPv6 destination unreachable message of
code 0 (no route to destination) <xref target='RFC4443' />. As
with IPv4, a router should generate an ICMPv6 destination
unreachable message of code 0 in response to a packet that
cannot be delivered to its destination address because it lacks
a matching entry in its routing table. As a result, TCP-LCD can
employ this ICMPv6 error messages as connectivity disruption
indication, too.</t>
</section>
<!-- ***** Subsection: TCP-LCD and IP Tunnels ***** -->
<section anchor="interaction_tunnels" title="TCP-LCD and IP Tunnels">
<t>It is worth noting that IP tunnels, including IPsec
<xref target='RFC4301' />, IP in IP <xref target='RFC2003' />,
Generic Routing Encapsulation (GRE) <xref target='RFC2784' />,
and others are compatible with TCP-LCD, as long as the received
ICMP unreachable messages can be demultiplexed and extracted
appropriately by the TCP sender during timeout-based loss
recovery.</t>
<t>If, for example, end-to-end tunnels like IPsec in transport
mode <xref target='RFC4301' /> are employed, a TCP sender may
receive ICMP unreachable messages where additional steps, e.g.,
decrypting in step (5) of the algorithm, are needed to extract
the TCP header from these ICMP messages. Provided that the
received ICMP unreachable message contains enough information,
i.e., SEQ.SEG is extractable, this information can still be
used as a valid input for the proposed algorithm.</t>
<t>Likewise, if IP encapsulation like <xref target='RFC2003' />
is used in some part of the path between the communicating
hosts, the tunnel ingress node may receive the ICMP unreachable
messages from an intermediate router experiencing the link
outage. Nevertheless, the tunnel ingress node may replay the
ICMP unreachable messages in order to inform the TCP sender. If
enough information is preserved to extract SEQ.SEG, the
replayed ICMP unreachable messages can still be used in
TCP-LCD.</t>
</section>
</section>
<!-- ***** Section: Experimental Results ***** -->
<!--
<section anchor="evaluation" title="Experimental Results">
</section>
-->
<!-- ***** Section: Related Work ***** -->
<section anchor="related_work" title="Related Work">
<t>Several methods that address TCP's problems in the presence of
connectivity disruptions have been proposed in literature. Some of
them try to improve TCP's performance by modifying lower layers.
For example, <xref target='SM03'/> introduces a "smart link layer",
which buffers one segment for each active connection and replays
these segments upon connectivity re-establishment. This approach
has a serious drawback: previously stateless intermediate routers
have to be modified in order to inspect TCP headers, to track the
end-to-end connection, and to provide additional buffer space. This
leads to an additional need of memory and processing power.</t>
<t>On the other hand, stateless link layer schemes, as proposed in
<xref target='RFC3819'/>, which unconditionally buffer some small
number of packets may have another problem: if a packet is buffered
longer than the maximum segment lifetime (MSL) of 2 min
<xref target='RFC0793' />, i.e., the disconnection lasts longer than
MSL, TCP's assumption that such segments will never be received
will no longer be true, violating TCP's semantics
<xref target='I-D.eggert-tcpm-tcp-retransmit-now' />.</t>
<t>Other approaches, like TCP-F <xref target='CRVP01' /> or the
Explicit Link Failure Notification (ELFN) <xref target='HV02' />
inform a TCP sender about a disrupted path by special messages
generated and sent from intermediate routers. In the case of a link
failure, the TCP sender stops sending segments and freezes its
retransmission timers. TCP-F stays in this state and remains silent
until either a "route establishment notification" is received or an
internal timer expires. In contrast, ELFN periodically probes the
network to detect connectivity re-establishment. Both proposals
rely on changes to intermediate routers, whereas the scheme
proposed in this document is a sender-only modification. Moreover,
ELFN does not consider congestion and may impose serious additional
load on the network, depending on the probe interval.</t>
<t>The authors of ATCP <xref target='LS01' /> propose enhancements
to identify different types of packet loss by introducing a layer
between TCP and IP. They utilize ICMP destination unreachable
messages to set TCP's receiver advertised window to zero, thus
forcing the TCP sender to perform zero window probing with an
exponential backoff. ICMP destination unreachable messages that
arrive during this probing period are ignored. This approach is
nearly orthogonal to this document, which exploits ICMP messages to
undo a retransmission timer backoff when TCP is already probing. In
principle, both mechanisms could be combined. However, due to
security considerations, it does not seem appropriate to adopt
ATCP's reaction, as discussed in
<xref target='discuss_steady-state' />.</t>
<t>Schuetz et al. <xref target='I-D.schuetz-tcpm-tcp-rlci' />
describe a set of TCP extensions that improve TCP's behavior when
transmitting over paths whose characteristics can change rapidly.
Their proposed extensions modify the local behavior of TCP and
introduce a new TCP option to signal locally received
connectivity-change indications (CCIs) to remote peers. Upon
receipt of a CCI, they re-probe the path characteristics either by
performing a speculative retransmission or by sending a single
segment of new data, depending on whether the connection is
currently stalled in exponential backoff or transmitting in
steady-state, respectively. The authors focus on specifying TCP
response mechanisms, nevertheless underlying layers would have to
be modified to explicitly send CCIs to make these immediate
responses possible.</t>
</section>
<!-- ***** Section: IANA Considerations ***** -->
<section anchor="iana" title="IANA Considerations">
<t>This memo includes no request to IANA.</t>
</section>
<!-- ***** Section: Security Considerations ***** -->
<section anchor="security" title="Security Considerations">
<t>The algorithm proposed in this document is considered to be
secure. For example, an attacker who already guessed the correct
four-tuple (i.e., Source IP Address, Source TCP port, Destination
IP Address, and Destination TCP port), can still not make a TCP
modified with TCP-LCD flood the network just by sending forged
ICMP unreachable messages in an attempt to maliciously shorten the
retransmission timer. The attacker additionally would need to guess
the correct segment sequence number of the current timeout-based
retransmission, with a probability of at most 1/2^32. Even in the
case of man-in-the-middle attacks, i.e., attacks performed in
scenarios in which the attacker can sniff the retransmissions, the
impact on network load is considered to be low, since the
retransmission frequency is limited by the RTO that was computed
before TCP had entered the timeout-based loss recovery. Hence, the
highest probing frequency is expected to be even lower than once
per minimum RTO, i.e. 1s as specified by
<xref target='RFC2988'/>.</t>
</section>
<!-- ***** Section: Acknowledgments ***** -->
<section anchor="acks" title="Acknowledgments">
<t>We would like to thank Lars Eggert, Mark Handley, Kai Jakobs,
Ilpo Jarvinen, Pasi Sarolahti, Tim Shepard, Joe Touch and Carsten
Wolff for feedback on earlier versions of this document. We also
thank Michael Faber, Daniel Schaffrath, and Damian Lukowski for
implementing and testing the algorithm in Linux. Special thanks go
to Ilpo Jarvinen for giving valuable feedback regarding the Linux
implementation.</t>
<t>This work has been supported by the German National Science Foundation
(DFG) within the research excellence cluster Ultra High-Speed Mobile
Information and Communication (UMIC), RWTH Aachen University.</t>
</section>
</middle>
<!-- ***** BACK MATTER ***** -->
<back>
<!-- There are 2 ways to insert reference entries from the citation
libraries:
1. define an ENTITY at the top, and use "ampersand character"RFC2629; here (as shown)
2. simply use a PI "less than character"?rfc include="reference.RFC.2119.xml"?> here
(for I-Ds: include="reference.I-D.narten-iana-considerations-rfc2434bis.xml")
Both are cited textually in the same manner: by using xref elements.
If you use the PI option, xml2rfc will, by default, try to find
included files in the same directory as the including file. You can
also define the XML_LIBRARY environment variable with a value
containing a set of directories to search. These can be either in
the local filing system or remote ones accessed by
http (http://domain/dir/... ).-->
<!-- References split into informative and normative -->
<references title="Normative References">
&rfc0792;
&rfc0793;
&rfc1812;
&rfc1323;
&rfc2988;
&rfc5681;
</references>
<references title="Informative References">
&rfc0791;
&rfc0826;
&rfc1122;
&rfc2003;
&rfc2119;
&rfc2460;
&rfc2784;
&rfc3522;
&rfc3168;
&rfc3782;
&rfc3819;
&rfc4015;
&rfc4301;
&rfc4443;
&rfc5461;
&rfc5682;
&rfc5927;
&retransmit-now;
&tcp-rlci;
<reference anchor="SESB05" target="">
<front>
<title>Protocol enhancements for intermittently connected
hosts
</title>
<author surname="Schuetz" initials="S."
fullname="Simon Schuetz"> <organization />
</author>
<author surname="Eggert" initials="L."
fullname="Lars Eggert"> <organization />
</author>
<author surname="Schmid" initials="S."
fullname="Stefan Schmid"> <organization />
</author>
<author surname="Brunner" initials="M."
fullname="Marcus Brunner"> <organization />
</author>
<date year="2005" month="December" />
</front>
<seriesInfo name="SIGCOMM Computer Communication Review"
value="vol. 35, no. 3, pp. 5-18" />
</reference>
<reference anchor="SM03" target="">
<front>
<title>Link layer-based TCP optimisation for disconnecting
networks
</title>
<author surname="Scott" initials="J."
fullname="James Scott"> <organization />
</author>
<author surname="Mapp" initials="G."
fullname="Glenford Mapp"> <organization />
</author>
<date year="2003" month="October" />
</front>
<seriesInfo name="SIGCOMM Computer Communication Review"
value="vol. 33, no. 5, pp. 31-42" />
</reference>
<reference anchor="CRVP01" target="">
<front>
<title>A feedback-based scheme for improving TCP performance
in ad hoc wireless networks
</title>
<author surname="Chandran" initials="K."
fullname="Kartik Chandran"> <organization />
</author>
<author surname="Raghunathan" initials="S."
fullname="Sudarshan Raghunathan"> <organization />
</author>
<author surname="Venkatesan" initials="S."
fullname="Subbarayan Venkatesan"> <organization />
</author>
<author surname="Prakash" initials="R."
fullname="Ravi Prakash"> <organization />
</author>
<date year="2001" month="February"/>
</front>
<seriesInfo name="IEEE Personal Communications"
value="vol. 8, no. 1, pp. 34-39" />
</reference>
<reference anchor="HV02" target="">
<front>
<title>Analysis of TCP performance over mobile ad hoc
networks
</title>
<author surname="Holland" initials="G."
fullname="Gavin Holland"> <organization />
</author>
<author surname="Vaidya" initials="N."
fullname="Nitin Vaidya"> <organization />
</author>
<date year="2002" month="March" />
</front>
<seriesInfo name="Wireless Networks"
value="vol. 8, no. 2-3, pp. 275-288" />
</reference>
<reference anchor="LS01" target="">
<front>
<title>ATCP: TCP for mobile ad hoc networks</title>
<author surname="Liu" initials="J."
fullname="Jian Liu"> <organization />
</author>
<author surname="Singh" initials="S."
fullname="Suresh Singh"> <organization />
</author>
<date year="July" month="2001"/>
</front>
<seriesInfo name="IEEE Journal on Selected Areas in
Communications" value="vol. 19, no. 7, pp. 1300-1315" />
</reference>
<reference anchor="Zh86" target="">
<front>
<title>Why TCP Timers Don't Work Well</title>
<author surname="Zhang" initials="L."
fullname="Lixia Zhang"> <organization />
</author>
<date year="1986" month="August"/>
</front>
<seriesInfo name="Proceedings of the Conference on Applications,
Technologies, Architectures, and Protocols for Computer
Communication (SIGCOMM'86)" value="pp. 397-405" />
</reference>
<reference anchor="KP87" target="">
<front>
<title>Improving Round-Trip Time Estimates in Reliable
Transport Protocols
</title>
<author surname="Karn" initials="P."
fullname="Phil Karn"> <organization />
</author>
<author surname="Partridge" initials="C."
fullname="Craig Partridge"> <organization />
</author>
<date year="1987" month="August"/>
</front>
<seriesInfo name="Proceedings of the Conference on Applications,
Technologies, Architectures, and Protocols for Computer
Communication (SIGCOMM'87)" value="pp. 2-7" />
</reference>
<!--
<reference anchor="ZSH08" target="">
<front>
<title>Improving TCP's Robustness to Long Connectivity
Disruptions</title>
<author surname="Zimmermann" initials="A."
fullname="Alexander Zimmermann"> <organization />
</author>
<author surname="Schaffrath" initials="D."
fullname="Daniel Schaffrath"> <organization />
</author>
<author surname="Hannemann" initials="A."
fullname="Arnd Hannemann"> <organization />
</author>
<date year="2008" month="November"/>
</front>
<seriesInfo name="Proceedings of the 20th IEEE Global
Communications Conference (GLOBECOM'08)"
value="pp. 5064-5069" />
</reference>
-->
</references>
<!-- ***** Section: Changes from previous versions of the draft ***** -->
<section anchor="changes" title="Changes from previous versions of the draft">
<t>This appendix should be removed by the RFC Editor before
publishing this document as an RFC.</t>
<section
anchor="changes_05" title="Changes from
draft-ietf-tcpm-tcp-lcd-01">
<t>
<list style="symbols">
<t>Incorporated feedback submitted by Lars Eggert</t>
</list>
</t>
</section>
<section anchor="changes_04" title="Changes from draft-ietf-tcpm-tcp-lcd-00">
<t>
<list style="symbols">
<t>Editorial changes.</t>
<t>Clarified TCP-LCD's behaviour during connection
establishment (Thanks to Mark Handley).</t>
</list>
</t>
</section>
<section anchor="changes_03" title="Changes from draft-zimmermann-tcp-lcd-02">
<t>
<list style="symbols">
<t>Incorporated feedback submitted by Ilpo Jarvinen.
<eref target="http://www.ietf.org/mail-archive/web/tcpm/current/msg04841.html" />
</t>
<t>Incorporated feedback submitted by Pasi Sarolahti.
<eref target="http://www.ietf.org/mail-archive/web/tcpm/current/msg04870.html" />
</t>
<t>Incorporated feedback submitted by Joe Touch.
<eref target="http://www.ietf.org/mail-archive/web/tcpm/current/msg04895.html" />
<eref target="http://www.ietf.org/mail-archive/web/tcpm/current/msg04900.html" />
</t>
<t>Extended and reorganized the discussion
(<xref target='discussion' />):
<list style="symbols">
<t>Every discussion item got its own title, so
that we have a better overview.</t>
<t>Extended Retransmission Ambiguity section. Added
also some references to the historical
retransmission ambiguity problem.</t>
<t>Heavily extended discussion about wrapped
sequence numbers (see Joe's comments).</t>
<t>Described the influence of packet duplication
on the algorithm (Thanks to Ilpo).</t>
<t>The section "Protecting Against Misbehaving
Routers" is not a subsection anymore. Moreover,
the section was renamed to "Dissolving Ambiguity
Issues" and has now real content.</t>
</list>
</t>
<t>An interoperability issues section
(<xref target='interoperability' />) was added. In
particular comments to ECN, ICMPv6, and to the two
thresholds R1 and R2 of <xref target="RFC1122" />
(Section 4.2.3.5) were added.</t>
<t>Miscellaneous editorial changes. In particular, the
algorithm has a name now: TCP-LCD.</t>
</list>
</t>
</section>
<section anchor="changes_02" title="Changes from draft-zimmermann-tcp-lcd-01">
<t>
<list style="symbols">
<t>The algorithm in <xref target='alg' /> was
slightly changed. Instead of reverting the last
retransmission timer backoff by halving the RTO, the
RTO is recalculated with help of the "BACKOFF_CNT"
variable. This fixes an issue that occurred when the
retransmission timer was backed off but bounded by a
maximum value. The algorithm in the previous version of
the draft, would have "reverted" to half of that
maximum value, instead of using the value, before the
RTO was doubled (and then bounded).</t>
<t>Miscellaneous editorial changes.</t>
</list>
</t>
</section>
<section anchor="changes_01" title="Changes from draft-zimmermann-tcp-lcd-00">
<t>
<list style="symbols">
<t>Miscellaneous editorial changes in Section
<xref target='terminology' format="counter" />,
<xref target='intro' format="counter" /> and
<xref target='cdi' format="counter" />.</t>
<t>The document was restructured in Section
<xref target='terminology' format="counter" />,
<xref target='intro' format="counter" /> and
<xref target='cdi' format="counter" /> for easier
reading. The motivation for the algorithm is changed
according TCP's problem to disambiguate congestion from
non-congestion loss.</t>
<t>Added <xref target='alg_idea' />.</t>
<t>The algorithm in <xref target='alg' /> was
restructured and simplified:
<list style="symbols">
<t>The special case of the first received ICMP
destination unreachable message after an RTO was
removed.</t>
<t>The "BACKOFF_CNT" variable was introduced so
it is no longer possible to perform more reverts
than backoffs.</t>
</list>
</t>
<t>The discussion in <xref target='discussion' /> was
improved and expanded according to the algorithm
changes.</t>
</list>
</t>
</section>
</section>
</back>
</rfc>
| PAFTECH AB 2003-2026 | 2026-04-21 10:25:16 |