One document matched: draft-ietf-sipping-sbc-funcs-03.txt
Differences from draft-ietf-sipping-sbc-funcs-02.txt
SIPPING Working Group J. Hautakorpi, Ed.
Internet-Draft G. Camarillo
Intended status: Informational Ericsson
Expires: October 19, 2007 R. Penfield
Acme Packet
A. Hawrylyshen
Ditech Networks Inc.
M. Bhatia
3CLogic
April 17, 2007
Requirements from SIP (Session Initiation Protocol) Session Border
Control Deployments
draft-ietf-sipping-sbc-funcs-03.txt
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on October 19, 2007.
Copyright Notice
Copyright (C) The IETF Trust (2007).
Abstract
This document describes functions implemented in Session Initiation
Hautakorpi, et al. Expires October 19, 2007 [Page 1]
Internet-Draft Requirements from SBC Deployments April 2007
Protocol (SIP) intermediaries known as Session Border Controllers
(SBCs). The goal of this document is to describe the commonly
provided functions of SBCs. A special focus is given to those
practices that are viewed to be in conflict with SIP architectural
principles. This document also explores the underlying requirements
of network operators that have led to the use of these functions and
practices in order to identify protocol requirements and determine
whether those requirements are satisfied by existing specifications
or additional standards work is required.
Hautakorpi, et al. Expires October 19, 2007 [Page 2]
Internet-Draft Requirements from SBC Deployments April 2007
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Background on SBCs . . . . . . . . . . . . . . . . . . . . . . 4
2.1. Peering Scenario . . . . . . . . . . . . . . . . . . . . . 5
2.2. Access Scenario . . . . . . . . . . . . . . . . . . . . . 6
3. Functions of SBCs . . . . . . . . . . . . . . . . . . . . . . 7
3.1. Topology Hiding . . . . . . . . . . . . . . . . . . . . . 8
3.1.1. General Information and Requirements . . . . . . . . . 8
3.1.2. Architectural Issues . . . . . . . . . . . . . . . . . 8
3.1.3. Example . . . . . . . . . . . . . . . . . . . . . . . 9
3.2. Media Traffic Shaping . . . . . . . . . . . . . . . . . . 10
3.2.1. General Information and Requirements . . . . . . . . . 10
3.2.2. Architectural Issues . . . . . . . . . . . . . . . . . 10
3.2.3. Example . . . . . . . . . . . . . . . . . . . . . . . 11
3.3. Fixing Capability Mismatches . . . . . . . . . . . . . . . 12
3.3.1. General Information and Requirements . . . . . . . . . 12
3.3.2. Architectural Issues . . . . . . . . . . . . . . . . . 12
3.3.3. Example . . . . . . . . . . . . . . . . . . . . . . . 13
3.4. Maintaining SIP-related NAT Bindings . . . . . . . . . . . 14
3.4.1. General Information and Requirements . . . . . . . . . 14
3.4.2. Architectural Issues . . . . . . . . . . . . . . . . . 15
3.4.3. Example . . . . . . . . . . . . . . . . . . . . . . . 15
3.5. Access Control . . . . . . . . . . . . . . . . . . . . . . 16
3.5.1. General Information and Requirements . . . . . . . . . 16
3.5.2. Architectural Issues . . . . . . . . . . . . . . . . . 16
3.5.3. Example . . . . . . . . . . . . . . . . . . . . . . . 17
3.6. Protocol Repair . . . . . . . . . . . . . . . . . . . . . 17
3.6.1. General Information and Requirements . . . . . . . . . 17
3.6.2. Architectural Issues . . . . . . . . . . . . . . . . . 18
3.6.3. Examples . . . . . . . . . . . . . . . . . . . . . . . 18
3.7. Media Encryption . . . . . . . . . . . . . . . . . . . . . 18
3.7.1. General Information and Requirements . . . . . . . . . 18
3.7.2. Architectural Issues . . . . . . . . . . . . . . . . . 19
3.7.3. Example . . . . . . . . . . . . . . . . . . . . . . . 19
4. Derived Requirements for Future SIP Standardization Work . . . 20
5. Security Considerations . . . . . . . . . . . . . . . . . . . 20
6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 21
7. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 21
8. References . . . . . . . . . . . . . . . . . . . . . . . . . . 21
8.1. Normative References . . . . . . . . . . . . . . . . . . . 21
8.2. Informational References . . . . . . . . . . . . . . . . . 21
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 22
Intellectual Property and Copyright Statements . . . . . . . . . . 23
Hautakorpi, et al. Expires October 19, 2007 [Page 3]
Internet-Draft Requirements from SBC Deployments April 2007
1. Introduction
In the past few years there has been a rapid adoption of the Session
Initiation Protocol (SIP) [1] and deployment of SIP-based
communications networks. This has often outpaced the development and
implementation of protocol specifications to meet network operator
requirements. This has led to the development of proprietary
solutions. Often, these proprietary solutions are implemented in
network intermediaries known in the marketplace as Session Border
Controllers (SBCs) because they typically are deployed at the border
between two networks. The reason for this is that network policies
are typically enforced at the edge of the network.
Even though many SBCs currently behave badly in a sense that they
break end-to-end security and impact feature negotiations, there is
clearly a market for them. Network operators need many of the
features current SBCs provide and often there are no standard
mechanisms available to provide them.
The purpose of this document is to describe functions implemented in
SBCs. A special focus is given to those practices that are
conflicting with SIP architectural principles in some way. The
document also explores the underlying requirements of network
operators that have led to the use of these functions and practices
in order to identify protocol requirements and determine whether
those requirements are satisfied by existing specifications or
additional standards work is required.
2. Background on SBCs
The term SBC is relatively non-specific, since it is not standardized
or defined anywhere. Nodes that may be referred to as SBCs but do
not implement SIP are outside the scope of this document.
SBCs usually sit between two service provider networks in a peering
environment, or between an access network and a backbone network to
provide service to residential and/or enterprise customers. They
provide a variety of functions to enable or enhance session-based
multi-media services (e.g., Voice over IP). These functions include:
a) perimeter defense (access control, topology hiding, and DoS
prevention and detection); b) functionality not available in the
endpoints (NAT traversal, protocol interworking or repair); and c)
network management (traffic monitoring, shaping, and QoS). Some of
these functions may also get integrated into other SIP elements (like
pre-paid platforms, 3GPP P-CSCF [5], 3GPP I-CSCF, etc).
SIP-based SBCs typically handle both signaling and media and can
Hautakorpi, et al. Expires October 19, 2007 [Page 4]
Internet-Draft Requirements from SBC Deployments April 2007
implement behavior which is equivalent to a "privacy service" (as
described in[2]) performing both Header Privacy and Session Privacy).
SBCs often modify certain SIP headers and message bodies that proxies
are not allowed to modify. Consequently, they are, by definition,
B2BUAs (Back-to-Back User Agents). The transparency of these B2BUAs
varies depending on the functions they perform. For example, some
SBCs modify the session description carried in the message and insert
a Record-Route entry. Other SBCs replace the value of the Contact
header field with the SBCs address, and generate a new Call-ID and
new To and From tags.
+-----------------+
| SBC |
[signaling] | +-----------+ |
<------------|->| signaling |<-|---------->
outer | +-----------+ | inner
network | | | network
| +-----------+ |
<------------|->| media |<-|---------->
[media] | +-----------+ |
+-----------------+
Figure 1: SBC architecture
Figure 1 shows the logical architecture of an SBC, which includes a
signaling and a media component. In this document, the terms outer
and inner network are used for describing these two networks.
2.1. Peering Scenario
A typical peering scenario involves two network operators who
exchange traffic with each other. For example, in a toll bypass
application, a gateway in operator A's network sends an INVITE that
is routed to the softswitch (proxy) in operator B's network. The
proxy responds with a redirect (3xx) message back to the originating
gateway that points to the appropriate terminating gateway in
operator B's network. The originating gateway then sends the INVITE
to the terminating gateway.
Hautakorpi, et al. Expires October 19, 2007 [Page 5]
Internet-Draft Requirements from SBC Deployments April 2007
Operator A . Operator B
.
. 2) INVITE
+-----+ . /--------------->+-----+
| SSA | . / 3) 3xx (redir.) | SSB |
+-----+ . / /---------------+-----+
. / /
+-----+ 1) INVITE +-----+--/ / +-----+
|GW-A1|---------------->| SBC |<---/ 4) INVITE |GW-B1|
+-----+ +-----+---------------------->+-----+
.
+-----+ . +-----+
|GW-A2| . |GW-B2|
+-----+ . +-----+
Figure 2: Peering with SBC
Figure 2 illustrates the peering arrangement with a SBC where
Operator A is the outer network, and Operator B is the inner network.
Operator B can use the SBC, for example, to control access to its
network, protect its gateways and softswitches from unauthorized use
and DoS attacks, and monitor the signaling and media traffic. It
also simplifies network management by minimizing the number ACL
(Access Control List) entries in the gateways. The gateways do not
need to be exposed to the peer network, and they can restrict access
(both media and signaling) to the SBCs. The SBC helps ensure that
only media from sessions the SBC authorizes will reach the gateway.
2.2. Access Scenario
In an access scenario, presented in Figure 3, the SBC is placed at
the border between the access network (outer network) and the
operator's network (inner network) to control access to the
operator's network, protect its components (media servers,
application servers, gateways, etc.) from unauthorized use and DoS
attacks, and monitor the signaling and media traffic. Also, since
the SBC is call stateful, it may provide access control functions to
prevent over subscription of the access links. Endpoints are
configured with the SBC as their outbound proxy address. The SBC
routes requests to one or more proxies in the operator network.
Hautakorpi, et al. Expires October 19, 2007 [Page 6]
Internet-Draft Requirements from SBC Deployments April 2007
Access Network Operator Network
+-----+
| UA1 |<---------\
+-----+ \
\
+-----+ \------->+-----+ +-------+
| UA2 |<-------------------->| SBC |<----->| proxy |<-- -
+-----+ /--->+-----+ +-------+
/
+-----+ +-----+ /
| UA3 +---+ NAT |<---/
+-----+ +-----+
Figure 3: Access scenario with SBC
The SBC may be hosted in the access network (e.g,. this is common
when the access network is an enterprise network), or in the operator
network (e.g., this is common when the access network is a
residential or small business network).
Some endpoints may be behind enterprise or residential NATs. In
cases where the access network is a private network, the SBC is the
NAT for all traffic. The proxy usually does authentication and/or
authorization for registrations and outbound calls. The SBC modifies
the REGISTER request so that subsequent requests to the registered
address-of-record are routed to the SBC. This is done either with a
Path header, or by modifying the Contact to point at the SBC.
The scenario presented in this section is a general one, and it
applies also to other similar settings. One example from a similar
setting is the one where an access network is the open internet, and
the operator network is the network of a SIP service provider.
3. Functions of SBCs
This section lists those functions that are used in SBC deployments
in current communication networks. Each subsection describes a
particular function or feature, the operators' requirements for
having it, explanation of any impact to the end-to-end SIP
architecture, and a concrete implementation example. Each section
also discusses potential concerns specific to that particular
implementation technique. Suggestions for alternative implementation
techniques that may be more architecturally compatible with SIP are
outside the scope of this document.
Hautakorpi, et al. Expires October 19, 2007 [Page 7]
Internet-Draft Requirements from SBC Deployments April 2007
All the examples given in this section are simplified; only the
relevant header lines from SIP and SDP [6] messages are displayed.
3.1. Topology Hiding
3.1.1. General Information and Requirements
Topology hiding consists of limiting the amount of topology
information given to external parties. Operators have a requirement
for this functionality because they do not want the IP addresses of
their equipment (proxies, gateways, application servers, etc) to be
exposed to outside parties. This may be because they do not want to
expose their equipment to DoS (Denial of Service) attacks, they may
use other carriers for certain traffic and do not want their
customers to be aware of it or they may want to hide their internal
network architecture from competitors or partners. In some
environments, the operator's customers may wish to hide the addresses
of their equipment or the SIP messages may contain private, non-
routable addresses.
The most common form of topology hiding is the application of header
privacy (see Section 5.1 of [2]), which involves stripping Via and
Record-Route headers, replacing the Contact header, and even changing
Call-IDs. However, in deployments which use IP addresses instead of
domain names in headers that cannot be removed (e.g. From and To
headers), the SBC may replace these IP addresses with its own IP
address or domain name.
3.1.2. Architectural Issues
This functionality is based on a hop-by-hop trust model as opposed to
an end-to-end trust model. The messages are modified without
subscriber consent and could potentially modify or remove information
about the user's privacy, security requirements and higher layer
applications which are communicating end-to-end using SIP. Neither
user agent in an end-to-end call has any way to distinguish the SBC
actions from a Man-In-The-Middle (MitM) attack.
Topology hiding function does not work well with Authenticated
Identity Management [3]. The Authenticated Identity Management
mechanism is based on a hash value that is calculated from parts of
From, To, Call-Id, CSeq, Date, and Contact header fields plus from
the whole message body. If the authentication service is not
provided by the SBC itself, the modification of the forementioned
header fields and the message body is in violation with [3]. Some
forms of topology hiding are in violation, because they are e.g.,
replacing the Contact header of a SIP message.
Hautakorpi, et al. Expires October 19, 2007 [Page 8]
Internet-Draft Requirements from SBC Deployments April 2007
3.1.3. Example
The current way of implementing topology hiding consists of having an
SBC act as a B2BUA (Back-to-Back User Agents) and remove all traces
of topology information (e.g., Via and Record-Route entries) from
outgoing messages.
Imagine the following example scenario: The SBC
(p4.domain.example.com) receives an INVITE request from the inner
network, which in this case is an operator network. The received SIP
message is shown in Figure 4.
INVITE sip:callee@u2.domain.example.com SIP/2.0
Via: SIP/2.0/UDP p3.middle.example.com;branch=z9hG4bK48jq9w9174131.1
Via: SIP/2.0/UDP p2.example.com;branch=z9hG4bK18an6i9234172.1
Via: SIP/2.0/UDP p1.example.com;branch=z9hG4bK39bn2e5239289.1
Via: SIP/2.0/UDP u1.example.com;branch=z9hG4bK92fj4u7283927.1
Contact: sip:caller@u1.example.com
Record-Route: <sip:p3.middle.example.com>
Record-Route: <sip:p2.example.com;lr>
Record-Route: <sip:p1.example.com;lr>
Figure 4: INVITE Request Prior to Topology Hiding
Then the SBC performs a topology hiding function. In this scenario,
the SBC removes and stores all existing Via and Record-Route headers,
and then inserts a Via and Record-Route header fields with its own
SIP URI. After the topology hiding function, the message could
appear as shown in Figure 5.
INVITE sip:callee@u2.domain.example.com SIP/2.0
Via: SIP/2.0/UDP p4.domain.example.com;branch=z9hG4bK92es3w1230129.1
Contact: sip:caller@u1.example.com
Record-Route: <sip:p4.domain.example.com;lr>
Figure 5: INVITE Request After Topology Hiding
Like a regular proxy server that inserts a Record-Route entry, the
SBC handles every single message of a given SIP dialog. If the SBC
loses state (e.g., the SBC restarts for some reason), it may not be
able to route messages properly. For example, if the SBC removes
"Via" entries from a request and then restarts, thus losing state,
the SBC may not be able to route responses to that request; depending
on the information that was lost when the SBC restarted.
This is only one example of topology hiding. In some cases, SBCs may
modify other headers, including the Contact header field values. The
header fields containing identity information is listed in Section
Hautakorpi, et al. Expires October 19, 2007 [Page 9]
Internet-Draft Requirements from SBC Deployments April 2007
4.1 of [2].
3.2. Media Traffic Shaping
3.2.1. General Information and Requirements
Media traffic shaping is the function of controlling media traffic.
Network operators may require this functionality in order to control
the traffic being carried on their network on behalf of their
subscribers. Traffic shaping helps the creation of different kinds
of billing models (e.g., video telephony can be priced differently to
voice-only calls) and it also makes it possible for operators to
enforce the usage of selected codecs. Additionally, traffic shaping
can be used to implement intercept capabilities where required to
support audit or legal obligations.
Since the media path is independent of the signaling path, the media
may not traverse through the operator's network unless the SBC
modifies the session description. By modifying the session
description the SBC can force the media to be sent through a media
relay which may be co-located with the SBC. This kind of traffic
shaping can be done, for example, to ensure a certain QoS (Quality of
Service) level.
Some operators do not want to reshape the traffic (e.g., allowing
only certain codecs), but only to monitor it for collecting
statistics and making sure that they are able to meet any business
service level agreements with their subscribers and/or partners. The
protocol techniques needed for monitoring media traffic are the same
as for reshaping media traffic.
SBCs on the media path are also capable of dealing with the "lost
BYE" issue if either endpoint dies in the middle of the session. The
SBC can detect that the media has stopped flowing and issue a BYE to
both sides to cleanup any state in other intermediate elements and
the endpoints.
One possible form of media traffic shaping is that SBCs terminate
media streams and SIP dialogs by generating BYE requests. This kind
of procedure can take place, for example, in a situation where
subscriber runs out of credits.
3.2.2. Architectural Issues
Implementing traffic shaping in this manner requires the SBC to
access and modify the session descriptions (i.e., offers and answers)
exchanged between the user-agents. Consequently, this approach does
not work if user-agents encrypt or integrity-protect their message
Hautakorpi, et al. Expires October 19, 2007 [Page 10]
Internet-Draft Requirements from SBC Deployments April 2007
bodies end-to-end. Again, messages are modified without subscriber
consent, and user-agents do not have any way to distinguish the SBC
actions from an attack by a MitM. Furthermore, this is in violation
with [3], see Section 3.1.2.
In this application, the SBC may originate messages that the user may
not be able to authenticate as coming from the dialog peer or the SIP
Registrar/Proxy.
3.2.3. Example
Traffic shaping may be performed in the following way: The SBC
behaves as a B2BUA and inserts itself, or some other entity under the
operator's control, in the media path. In practice, the SBC modifies
the session descriptions carried in the SIP messages. As a result,
the SBC receives media from one user-agent and relays it to the other
user-agent and performs the identical operation with media traveling
in the reverse direction.
As mentioned in Section 3.2.1, codec restriction is a form of traffic
shaping. The SBC restricts the codec set negotiated in the offer/
answer exchange [4] between the user-agents. After modifying the
session descriptions, the SBC can check whether or not the media
stream corresponds to what was negotiated in the offer/answer
exchange. If it differs, the SBC has the ability to terminate the
media stream or take other appropriate (configured) actions (e.g.
raise an alarm).
Consider the following example scenario: The SBC receives an INVITE
request from the outer network, which in this case is an access
network. The received SIP message contains the SDP session
descriptor shown in Figure 6.
v=0
o=mhandley 2890844526 2890842807 IN IP4 192.0.2.4
c=IN IP4 192.0.2.4
m=audio 49230 RTP/AVP 96 98
a=rtpmap:96 L8/8000
a=rtpmap:98 L16/16000/2
Figure 6: Request Prior to Media Shaping
In this example, the SBC performs the media traffic shaping function
by rewriting the 'm' line, and removing one 'a' line according to
some (external) policy. Figure 7 shows the session description after
the traffic shaping function.
Hautakorpi, et al. Expires October 19, 2007 [Page 11]
Internet-Draft Requirements from SBC Deployments April 2007
v=0
o=mhandley 2890844526 2890842807 IN IP4 192.0.2.4
c=IN IP4 192.0.2.4
m=audio 49230 RTP/AVP 96
a=rtpmap:96 L8/8000
Figure 7: Request Body After Media Shaping
Media traffic shaping has a problem where the SBC needs to understand
the session description protocol and all extensions used by the user-
agents. This means that in order to use a new extension (e.g., an
extension to implement a new service) or a new session description
protocol, SBCs in the network may need to be upgraded in conjunction
with the endpoints. It is noteworthy that similar problem, but with
header fields, applies to, for example, topology hiding function, see
Section 3.1. Certain extensions that do not require active
manipulation of the session descriptors to facilitate traffic shaping
will be able to be deployed without upgrading existing SBCs,
depending on the degree of transparency the SBC implementation
affords. In cases requiring an SBC modification to support the new
protocol features, the rate of service deployment may be affected.
3.3. Fixing Capability Mismatches
3.3.1. General Information and Requirements
SBCs fixing capability mismatches enable communications between user-
agents with different capabilities or extensions. For example, user-
agents on networks which implement SIP differently (for example 3GPP
or Packet Cable etc) or those that support different IP versions,
different codecs, or that are in different address realms. Operators
have a requirement and a strong motivation for performing capability
mismatch fixing, so that they can provide transparent communication
across different domains. In some cases different SIP extensions or
methods to implement the same SIP application (like monitoring
session liveness, call history/diversion etc) may also be interworked
through the SBC.
3.3.2. Architectural Issues
SBCs fixing capability mismatches insert a media element in the media
path using the procedures described in Section 3.2. Therefore, these
SBCs have the same concerns as SBCs performing traffic shaping: the
SBC modifies SIP messages without explicit consent from any of the
user-agents. This may break end-to-end security and application
extensions negotiation.
The capability mismatch fixing is a fragile function in the long
Hautakorpi, et al. Expires October 19, 2007 [Page 12]
Internet-Draft Requirements from SBC Deployments April 2007
term. The number of incompatibilities built into various network
elements is increasing the fragility and complexity over time. This
might lead to a situation where SBCs need to be able to handle a
large number of capability mismatches in parallel.
3.3.3. Example
Consider the following example scenario where the inner network is an
access network using IPv4 and the outer network is using IPv6. The
SBC receives an INVITE request with a session description from the
access network:
INVITE sip:callee@ipv6.domain.example.com SIP/2.0
Via: SIP/2.0/UDP 192.0.2.4
Contact: sip:caller@u1.example.com
v=0
o=mhandley 2890844526 2890842807 IN IP4 192.0.2.4
c=IN IP4 192.0.2.4
m=audio 49230 RTP/AVP 96
a=rtpmap:96 L8/8000
Figure 8: Request Prior to Capabilities Match
Then the SBC performs a capability mismatch fixing function. In this
scenario the SBC inserts Record-Route and Via headers, and rewrites
the 'c' line from the sessions descriptor. Figure 9 shows the
request after the capability mismatch adjustment.
INVITE sip:callee@ipv6.domain.com SIP/2.0
Record-Route: <sip:[2001:DB8::801:201:2ff:fe94:8e10];lr>
Via: SIP/2.0/UDP sip:[2001:DB8::801:201:2ff:fe94:8e10]
Via: SIP/2.0/UDP 192.0.2.4
Contact: sip:caller@u1.example.com
v=0
o=mhandley 2890844526 2890842807 IN IP4 192.0.2.4
c=IN IP6 2001:DB8::801:201:2ff:fe94:8e10
m=audio 49230 RTP/AVP 96
a=rtpmap:96 L8/8000
Figure 9: Request After Capability Match
This message is then sent by the SBC to the onward IPv6 network.
Hautakorpi, et al. Expires October 19, 2007 [Page 13]
Internet-Draft Requirements from SBC Deployments April 2007
3.4. Maintaining SIP-related NAT Bindings
3.4.1. General Information and Requirements
NAT traversal in this instance refers to the specific message
modifications required to assist a user-agent in maintaining SIP and
media connectivity when there is a NAT device located between a user-
agent and a proxy/registrar and, possibly, any other user-agent.
An SBC performing a NAT (Network Address Translator) traversal
function for a user agent behind a NAT sits between the user-agent
and the registrar of the domain. NATs are widely deployed in various
access networks today, so operators have a requirement to support it.
When the registrar receives a REGISTER request from the user-agent
and responds with a 200 (OK) response, the SBC modifies such a
response decreasing the validity of the registration (i.e., the
registration expires sooner). This forces the user-agent to send a
new REGISTER to refresh the registration sooner that it would have
done on receiving the original response from the registrar. The
REGISTER requests sent by the user-agent refresh the binding of the
NAT before the binding expires.
Note that the SBC does not need to relay all the REGISTER requests
received from the user-agent to the registrar. The SBC can generate
responses to REGISTER requests received before the registration is
about to expire at the registrar. Moreover, the SBC needs to
deregister the user-agent if this fails to refresh its registration
in time, even if the registration at the registrar would still be
valid.
Operators implement this functionality in an SBC instead of in the
registrar for several reasons: (i) preventing packets from
unregistered users to prevent chances of DoS attack, (ii)
prioritization and/or re-routing of traffic (based on user or
service, like E911) as it enters the network, and (iii) performing a
load balancing function or reducing the load on other network
equipment.
SBCs can also force traffic to go through a media relay for NAT
traversal purposes (more about media traffic shaping in Section 3.2).
A typical call has media streams to two directions. Even though SBCs
can force media streams from both directions to go through a media
relay, it is usually enough to relay only the media from one
direction.
Hautakorpi, et al. Expires October 19, 2007 [Page 14]
Internet-Draft Requirements from SBC Deployments April 2007
3.4.2. Architectural Issues
This approach to NAT traversal does not work when end-to-end
confidentiality or integrity-protection is used. The SBC would be
seen as a MitM modifying the messages between the user-agent and the
registrar.
There is also a problem related to the method how SBCs choose the
value for the validity of a registration period. This value should
be as high as possible, but it still needs to be low enough to
maintain the NAT binding. Typically SBCs do not have any
deterministic method for choosing a suitable value.
3.4.3. Example
Consider the following example scenario: The SBC resides between the
UA and Registrar. Previously the UA has sent a REGISTER request to
Registrar, and the SBC receives the registration response shown in
Figure 10.
SIP/2.0 200 OK
From: Bob <sip:bob@biloxi.example.com>;tag=a73kszlfl
To: Bob <sip:bob@biloxi.example.com>;tag=34095828jh
CSeq: 1 REGISTER
Contact: <sips:bob@client.biloxi.example.com>;expires=3600
Figure 10: Response Prior to NAT Maintenance Function
When performing the NAT traversal function, the SBC may re-write the
expiry time to coax the UA to re-register prior to the intermediating
NAT deciding to close the pinhole. Figure 11 shows a possible
modification of the response from Figure 10.
SIP/2.0 200 OK
From: Bob <sip:bob@biloxi.example.com>;tag=a73kszlfl
To: Bob <sip:bob@biloxi.example.com>;tag=34095828jh
CSeq: 1 REGISTER
Contact: <sips:bob@client.biloxi.example.com>;expires=60
Figure 11: Manipulated Response for NAT Traversal
Naturally also other measures need to be taken in order to enable the
NAT traversal, but this example illustrates only one mechanism for
preserving the SIP related NAT bindings.
Hautakorpi, et al. Expires October 19, 2007 [Page 15]
Internet-Draft Requirements from SBC Deployments April 2007
3.5. Access Control
3.5.1. General Information and Requirements
Network operators may wish to control what kind of signaling and
media traffic their network carries. There is strong motivation and
a requirement to do access control on the edge of an operator's
network. Access control can be based on, for example, link-layer
identifiers, IP addresses or SIP identities.
This function can be implemented by protecting the inner network with
firewalls and configuring them so that they only accept SIP traffic
from the SBC. This way, all the SIP traffic entering the inner
network needs to be routed though the SBC, which only routes messages
from authorized parties or traffic that meets a specific policy that
is expressed in the SBC administratively.
Access control can be applied either only to the signaling, or to
both the signaling and media. If it is applied only to the
signaling, then the SBC might behave as a proxy server. If access
control is applied to both the signaling and media, then the SBC
behaves in a similar manner as explained in Section 3.2. A key part
of media-layer access control is that only media for authorized
sessions is allowed to pass through the SBC and/or associated media
relay devices.
In environments where there is limited bandwidth on the access links,
the SBC can compute the potential bandwidth usage by examining the
codecs present in SDP offers and answers. With this information, the
SBC can reject sessions before the available bandwidth is exhausted
to allow existing sessions to maintain acceptable quality of service.
Otherwise, the link could become over subscribed and all sessions
would experience a deterioration in quality of service. SBCs may
contact a policy server to determine whether sufficient bandwidth is
available on a per-session basis.
3.5.2. Architectural Issues
Since the SBC needs to handle all SIP messages, this function has
scalability implications. In addition, the SBC is a single point of
failure from an architectural point of view. Although, in practice,
many current SBCs have the capability to support redundant
configuration, which prevents the loss of calls and/or sessions in
the event of a failure on a single node.
If access control is performed only on behalf of signaling, then the
SBC is compatible with general SIP architectural principles, but if
it is performed for signaling and for media, then there are similar
Hautakorpi, et al. Expires October 19, 2007 [Page 16]
Internet-Draft Requirements from SBC Deployments April 2007
problems as described in Section 3.2.2.
3.5.3. Example
Figure 12 shows a callflow where the SBC is providing both signaling
and media access control (ACKs omitted for brevity).
caller SBC callee
| | |
| Identify the caller | |
|<- - - - - - - - - - - >| |
| | |
| INVITE + SDP | |
|----------------------->| |
| [Modify the SDP] |
| | INVITE + modified SDP |
| |----------------------->|
| | |
| | 200 OK + SDP |
| |<-----------------------|
| [Modify the SDP] |
| | |
| 200 OK + modified SDP | |
|<-----------------------| |
| | |
| Media [Media inspection] Media |
|<======================>|<======================>|
| | |
Figure 12: Example Access Callflow
In this scenario, the SBC first identifies the caller, so it can
determine whether or not to give signaling access for the caller.
This might be achieved using information gathered during
registration, or by other means. Some SBCs may rely on the proxy to
authenticate the user-agent placing the call. After identification,
the SBC modifies the session descriptors in INVITE and 200 OK
messages in a way that the media is going to flow through SBC itself.
When the media starts flowing, the SBC can inspect whether the callee
and caller use the codec(s) that they had previously agreed on.
3.6. Protocol Repair
3.6.1. General Information and Requirements
SBC are also used to repair protocol messages generated by not-fully-
standard clients. Operators may wish to support protocol repair, if
they want to support as many clients as possible. It is noteworthy,
Hautakorpi, et al. Expires October 19, 2007 [Page 17]
Internet-Draft Requirements from SBC Deployments April 2007
that this function affects only the signaling component of SBC, and
that protocol repair function is not the same as protocol conversion.
3.6.2. Architectural Issues
In most cases, this function can be seen as being compatible with SIP
architectural principles, and it does not violate the end-to-end
model of SIP. The SBC repairing protocol messages behaves as a proxy
server that is liberal in what it accepts and strict in what it
sends.
A similar problem related to increasing complexity, as explained in
Section 3.3.2, also affects protocol repair function.
3.6.3. Examples
The SBC can, for example, receive an INVITE message from a relatively
new SIP UA as illustrated in Figure 13.
INVITE sip:callee@sbchost.example.com
Via: SIP/2.0/UDP u1.example.com:5060;lr
From: Caller <sip:caller@one.example.com>
To: Callee <sip:callee@two.example.com>
Call-ID: 18293281@u1.example.com
CSeq: 1 INVITE
Contact: sip:caller@u1.example.com
Figure 13: Request from a relatively new client
If the SBC does protocol repair, it can re-write the 'lr' parameter
on the Via header field into the form 'lr=true', in order to support
some older, non-standard SIP stacks. It could also remove excess
white spaces to make the SIP message more human readable.
3.7. Media Encryption
3.7.1. General Information and Requirements
SBCs are used to perform media encryption / decryption at the edge of
the network. This is the case when media encryption is used only on
the access network (outer network) side and the media is carried
unencrypted in the inner network. Operators may have an obligation
to provide the ability to do legal interception, while they still
want to give their customers the ability to encrypt media in the
access network. This leads to a situation where operators have a
requirement to perform media encryption function.
Hautakorpi, et al. Expires October 19, 2007 [Page 18]
Internet-Draft Requirements from SBC Deployments April 2007
3.7.2. Architectural Issues
While performing a media encryption function, SBCs need to be able to
inject either themselves, or some other entity to the media path.
Due to this, the SBCs have the same architectural issues as explained
in Section 3.2.
3.7.3. Example
Figure 14 shows an example where the SBC is performing media
encryption related functions (ACKs omitted for brevity).
caller SBC#1 SBC#2 callee
| | | |
| INVITE + SDP | | |
|------------------->| | |
| [Modify the SDP] | |
| | | |
| | INVITE + mod. SDP | |
| |------------------->| |
| | [Modify the SDP] |
| | | |
| | | INVITE + mod. SDP |
| | |------------------->|
| | | |
| | | 200 OK + SDP |
| | |<-------------------|
| | [Modify the SDP] |
| | | |
| | 200 OK + mod. SDP | |
| |<-------------------| |
| [Modify the SDP] | |
| | | |
| 200 OK + mod. SDP | | |
|<-------------------| | |
| | | |
| Encrypted | Plain | Encrypted |
| media [enc./dec.] media [enc./dec.] media |
|<==================>|<- - - - - - - - ->|<==================>|
| | | |
Figure 14: Media Encryption Example
First the UAC sends an INVITE request , and the first SBC modifies
the session descriptor in a way that it injects itself to the media
path. The same happens in the second SBC. Then the UAS replies with
a 200 OK response, the SBCs inject themselves in the returning media
path. After signaling the media start flowing, and both SBCs are
Hautakorpi, et al. Expires October 19, 2007 [Page 19]
Internet-Draft Requirements from SBC Deployments April 2007
performing media encryption and decryption.
4. Derived Requirements for Future SIP Standardization Work
Some of the functions listed in this document are more SIP-unfriendly
than others. This list requirements that are derived from the
functions that break the principles of SIP in one way or another.
The derived requirements are:
Req-1: There should be a SIP-friendly way to hide network topology
information. Currently this is done by stripping and
replacing header fields, which is against the principles of
SIP.
Req-2: There should be a SIP-friendly way to direct media traffic
through intermediaries. Currently this is done without user
consent by modifying session descriptors, which is against
the principles of SIP.
Req-3: There should be a SIP-friendly way to fix capability
mismatches in SIP messages. This requirement is harder to
fulfill on complex mismatch cases, like the 3GPP/Packet Cable
mismatch. Currently this is done by modifying SIP messages,
which violates end-to-end security.
All the above-mentioned requirements are such that they do not have
an existing solution today. Thus, future work is needed in order to
develop solutions to these requirements.
5. Security Considerations
Many of the functions this document describes have important security
and privacy implications. One major security problem is that many
functions implemented by SBCs (e.g., topology hiding and media
traffic shaping) modify SIP messages and their bodies without the
user agents' consent. The result is that the user agents may
interpreted the actions taken by SBC as a MitM attack.
SBCs that place themselves (or another entity) on the media path can
be used to eavesdrop conversations. Since, often, user agents cannot
distinguish between the actions of an attacker and those of a SBC,
users cannot know whether they are being eavesdropped or a SBC on the
path is performing some other function.
A SBC is a single point of failure form the architectural point of
view. This makes it an attractive target for DoS attacks. The fact
that some functions of SBCs require those SBCs to maintain session
specific information makes the situation even worse. If the SBC
Hautakorpi, et al. Expires October 19, 2007 [Page 20]
Internet-Draft Requirements from SBC Deployments April 2007
crashes (or is brought down by an attacker), ongoing sessions
experience undetermined behavior.
If the IETF decides to develop standard mechanisms to address the
requirements presented in Section 4, the security and privacy-related
aspects of those mechanisms will, of course, need to be taken into
consideration.
6. IANA Considerations
This document has no IANA considerations.
7. Acknowledgements
The ad-hoc meeting about SBCs, held on Nov 9th 2004 at Washington DC
during the 61st IETF meeting, provided valuable input to this
document. Authors would also like to thank Sridhar Ramachandran,
Gaurav Kulshreshtha, and Rakendu Devdhar. Reviewers Spencer Dawkins
and Francois Audet also deserve special thanks.
8. References
8.1. Normative References
[1] Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A.,
Peterson, J., Sparks, R., Handley, M., and E. Schooler, "SIP:
Session Initiation Protocol", RFC 3261, June 2002.
[2] Peterson, J., "A Privacy Mechanism for the Session Initiation
Protocol (SIP)", RFC 3323, November 2002.
[3] Peterson, J. and C. Jennings, "Enhancements for Authenticated
Identity Management in the Session Initiation Protocol (SIP)",
RFC 4474, August 2006.
[4] Rosenberg, J. and H. Schulzrinne, "An Offer/Answer Model with
Session Description Protocol (SDP)", RFC 3264, June 2002.
8.2. Informational References
[5] 3GPP, "IP Multimedia Subsystem (IMS); Stage 2", 3GPP TS 23.228
5.15.0, June 2006.
[6] Handley, M. and V. Jacobson, "SDP: Session Description
Protocol", RFC 2327, April 1998.
Hautakorpi, et al. Expires October 19, 2007 [Page 21]
Internet-Draft Requirements from SBC Deployments April 2007
Authors' Addresses
Jani Hautakorpi (editor)
Ericsson
Hirsalantie 11
Jorvas 02420
Finland
Email: Jani.Hautakorpi@ericsson.com
Gonzalo Camarillo
Ericsson
Hirsalantie 11
Jorvas 02420
Finland
Email: Gonzalo.Camarillo@ericsson.com
Robert F. Penfield
Acme Packet
71 Third Avenue
Burlington, MA 01803
US
Email: bpenfield@acmepacket.com
Alan Hawrylyshen
Ditech Networks Inc.
Suite 200, 1167 Kensington Cres NW
Calgary, Alberta T2N 1X7
Canada
Email: ahawrylyshen@ditechnetworks.com
Medhavi Bhatia
3CLogic
9700 Great Seneca Hwy.
Rockville, MD 20850
US
Email: mbhatia@3clogic.com
Hautakorpi, et al. Expires October 19, 2007 [Page 22]
Internet-Draft Requirements from SBC Deployments April 2007
Full Copyright Statement
Copyright (C) The IETF Trust (2007).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgment
Funding for the RFC Editor function is provided by the IETF
Administrative Support Activity (IASA).
Hautakorpi, et al. Expires October 19, 2007 [Page 23]
| PAFTECH AB 2003-2026 | 2026-04-24 05:46:18 |