One document matched: draft-ietf-psamp-framework-10.txt
Differences from draft-ietf-psamp-framework-09.txt
Internet Draft Nick Duffield (Editor)
Category: Informational AT&T Labs - Research
Document: <draft-ietf-psamp-framework-10.txt> January 2005
Expires: July 2005
A Framework for Packet Selection and Reporting
Status of this Memo
This document is an Internet-Draft and is subject to all
provisions of section 3 of RFC 3667. By submitting this
Internet-Draft, each author represents that any applicable patent
or other IPR claims of which he or she is aware have been or will
be disclosed, and any of which he or she become aware will be
disclosed, in accordance with RFC 3668.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as
Internet-Drafts. Internet-Drafts are draft documents valid for a
maximum of six months and may be updated, replaced, or obsoleted
by other documents at any time. It is inappropriate to use
Internet-Drafts as reference material or to cite them other than
as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Abstract
This document specifies a framework for the PSAMP (Packet
SAMPling) protocol. The functions of this protocol are to select
packets from a stream according to a set of standardized
selectors, to form a stream of reports on the selected packets,
and to export the reports to a collector. This framework details
the components of this architecture, then describes some generic
requirements, motivated by the dual aims of ubiquitous deployment
and utility of the reports for applications. Detailed
requirements for selection, reporting and exporting are
described, along with configuration requirements of the PSAMP
functions.
Comments on this document should be addressed to the PSAMP
Working Group mailing list: psamp@ops.ietf.org
Duffield (Ed.) Expires July 2005 [Page 1]
Internet Draft Packet Selection and Reporting January 2005
To subscribe: psamp-request@ops.ietf.org, in body: subscribe
Archive: https://ops.ietf.org/lists/psamp/
Table of Contents
1. Introduction................................................3
2. PSAMP Documents Overview....................................4
3. Elements, Terminology and High-level Architecture...........4
3.1 High-level description of the PSAMP Architecture............4
3.2 Observation Points, Packet Streams and Packet Content.......5
3.3 Selection Process...........................................6
3.4 Reporting Process...........................................7
3.5 Measurement Process.........................................8
3.6 Exporting Process...........................................8
3.7 PSAMP Device................................................8
3.8 Collector...................................................8
3.9 Possible Configurations.....................................9
3.10 PSAMP and IPFIX Interaction................................10
4. Generic Requirements for PSAMP.............................11
4.1 Generic Selection Process Requirements.....................11
4.2 Generic Reporting Process Requirements.....................11
4.3 Generic Exporting Process Requirements.....................12
4.4 Generic Configuration Requirements.........................12
5. Packet Selection...........................................13
5.1 Two Types of Selector......................................13
5.2 PSAMP Packet Selectors.....................................14
5.3 Selection Fraction Terminology.............................16
5.4 Input Sequence Numbers for Primitive Selectors.............17
5.5 Composite Selectors........................................18
5.6 Constraints on the Selection Fraction......................18
6. Reporting Process..........................................18
6.1 Mandatory Contents of Packet Reports: Basic Reports........19
6.2 Extended Packet Reports....................................19
6.3 Extended Packet Reports in the Presence of IPFIX...........20
6.4 Report Interpretation......................................20
7. Parallel Measurement Processes.............................21
8. Exporting Process..........................................21
8.1 Use of IPFIX...............................................21
8.2 Congestion-aware Unreliable Transport......................22
8.3 Configurable Export Rate Limit.............................22
8.4 Limiting Delay for Export Packets..........................23
8.5 Export Packet Compression..................................24
8.6 Collector Destination......................................24
8.7 Local Export...............................................24
9. Configuration and Management...............................24
10. Feasibility and Complexity.................................25
10.1 Feasibility................................................25
10.1.1 Filtering................................................25
10.1.2 Sampling.................................................25
10.1.3 Hashing..................................................26
10.1.4 Reporting................................................26
Duffield (Ed.) Expires July 2005 [Page 2]
Internet Draft Packet Selection and Reporting January 2005
10.1.5 Exporting................................................26
10.2 Potential Hardware Complexity..............................26
11. Applications...............................................27
11.1 Baseline Measurement and Drill Down........................28
11.2 Trajectory Sampling........................................28
11.3 Passive Performance Measurement............................29
11.4 Troubleshooting............................................29
12. Security Considerations....................................30
13. IANA Considerations........................................30
14. Normative References.......................................30
15. Informative References.....................................31
16. Authors' Addresses.........................................33
17. Intellectual Property Statements...........................34
18. Full Copyright Statement...................................34
19. Disclaimers................................................35
Copyright (C) The Internet Society (2004). All Rights Reserved.
This document is an Internet-Draft and is in full conformance
with all provisions of Section 10 of RFC 2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as
Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other
documents at any time. It is inappropriate to use
Internet-Drafts as reference material or to cite them other than
as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL
NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
RFC 2119.
1. Introduction
This document describes the PSAMP framework for network elements
to select subsets of packets by statistical and other methods,
and to export a stream of reports on the selected packets to a
collector.
The motivation for the PSAMP standard comes from the need for
measurement-based support for network management and control
Duffield (Ed.) Expires July 2005 [Page 3]
Internet Draft Packet Selection and Reporting January 2005
across multivendor domains. This requires domain-wide consistency
in the types of selection schemes available, and the manner in
which the resulting measurements are presented and interpreted.
The motivation for specific packet selection operations comes
from the applications that they enable. Development of the PSAMP
standard is open to influence by the requirements of standards in
related IETF Working Groups, for example, IP Performance Metrics
(IPPM) [RFC-2330] and Internet Traffic Engineering (TEWG).
The name PSAMP is a contraction of the phrase Packet Sampling.
The word "sampling" captures the idea that only a subset of all
packets passing a network element will be selected for reporting.
But PSAMP selection operations include random selection,
deterministic selection (filtering), and deterministic
approximations to random selection (hash-based selection).
2. PSAMP Documents Overview
PSAMP-FW: "A Framework for Packet Selection and Reporting" (this
document). This document describes the PSAMP framework for
network elements to select subsets of packets by statistical and
other methods, and to export a stream of reports on the selected
packets to a collector. Definitions of terminology and the use of
the terms "must", "should" and "may" in this document are
informational only.
[PSAMP-TECH]: "Sampling and Filtering Techniques for IP Packet
Selection", describes the set of packet selection techniques
supported by PSAMP.
[PSAMP-MIB]: "Definitions of Managed Objects for Packet Sampling"
describes the PSAMP Management Information Base
[PSAMP-PROTO]: "Packet Sampling (PSAMP) Protocol Specifications"
specifies the export of packet information from a PSAMP Exporting
Process to a PSAMP Colleting Process
[PSAMP-INFO]: "Information Model for Packet Sampling Exports"
defines an information and data model for PSAMP.
3. Elements, Terminology and High-level Architecture
3.1 High-level description of the PSAMP Architecture
Here is an informal high level description of the PSAMP protocol
operating in a PSAMP device (all terms will be defined
presently). A stream of packets is observed at an observation
point. A selection process inspects each packet to determine
whether it should be selected. A reporting process constructs a
report on each selected packet, using the packet content, and
Duffield (Ed.) Expires July 2005 [Page 4]
Internet Draft Packet Selection and Reporting January 2005
possibly other information such as the packet treatment or the
arrival timestamp. An exporting process sends the reports to a
collector, together with any subsidiary information needed for
their interpretation.
The following figure indicates the sequence of the three
processes (selection, reporting, and exporting) within the PSAMP
device. The composition of the selection process followed by the
reporting process is known as the measurement process.
+---------+ +---------+ +---------+
Observed |Selection| |Reporting| |Exporting|
Packet--->|Process |--->|Process |--->|Process |--->Collector
Stream +---------+ +---------+ +---------+
\----Measurement Process-----/
The following sections give the detailed definitions of each of
all the objects just named.
3.2 Observation Points, Packet Streams and Packet Content
This section contains the definition of terms relevant to
obtaining the packet input to the selection process.
* Observation Point
An observation point is a location in the network where packets
can be observed. Examples include:
(i) a line to which a probe is attached;
(ii) a shared medium, such as an Ethernet-based LAN;
(iii) a single port of a router, or set of interfaces
(physical or logical) of a router;
(iv) an embedded measurement subsystem within an
interface.
Note that one Observation Point may be a superset of several
other Observation Points. For example one Observation Point
can be an entire line card. This would be the superset of the
individual Observation Points at the line card's interfaces.
* Observed Packet Stream
The observed packet stream is the set of all packets observed
at the Observation Point.
* Packet Stream
A packet stream denotes a subset of the Observed Packet Stream
that flows past some specified point within the measurement
process. An example of a Packet Stream is the output of the
selection process.
Duffield (Ed.) Expires July 2005 [Page 5]
Internet Draft Packet Selection and Reporting January 2005
* Packet Content
The packet content denotes the union of its associated headers
(including data link layer, network layer and other
encapsulation headers) and the packet payload.
Note that packets selected from a Packet Stream, e.g. by
sampling, do not necessarily possess a property by which they can
be distinguished from packets that have not been selected. For
this reason the term "stream" is favored over "flow", which is
defined as set of packets with common properties [RFC-3917].
3.3 Selection Process
This section defines the selection process and related objects.
* Selection Process
A selection process takes the Observed Packet Stream as its
input and selects a subset of that stream as its output.
* Selection State:
A Selection Process may maintain state information for use
by the Selection Process and/or the Reporting Process. The
selection state may depend on the current packet, packets
observed earlier, and other variables, for example:
(i) sequence numbers of packets at the input of
selectors;
(ii) a timestamp of observation of the packet at the
Observation Point;
(iii) iterators for pseudorandom number generators;
(iv) hash values calculated during selection;
(v) indicators of whether the packet was selected by
a given selector;
Selection Processes may change the Selection State as a
result of processing a packet. Selection State for a packet
is to reflect the state after processing the packet.
* Selector:
A selector defines the action of a Selection Process on a
single packet of its input. If selected, the packet becomes
an element of the output Packet Stream from the selector.
Duffield (Ed.) Expires July 2005 [Page 6]
Internet Draft Packet Selection and Reporting January 2005
The Selector can make use of the following information in
determining whether a packet is selected:
(i) the packet's content;
(ii) information derived from the packet's treatment at the
Observation Point;
(iii) any Selection State that may be maintained by the
Selection Process.
* Composite Selector:
A composite selector is an ordered composition of Selectors,
in which the output Packet Stream issuing from one Selector
forms the input Packet Stream to the succeeding Selector.
* Primitive Selector:
A Selector is primitive if it is not a Composite Selector.
3.4 Reporting Process
* Reporting Process:
A reporting process creates a report stream from the packets
selected by a Selection Process, in preparation for export.
The input to the Reporting Process comprises that
information available to the Selection Process per selected
packet, specifically:
(i) the selected packet's content;
(ii) information derived from the selected packet's
treatment at the Observation Point;
(iii) any Selection State maintained by the inputting
Selection Process, reflecting any modifications to the
Selection State made during selection of the packet.
* Report Stream:
The report stream is the output of a reporting process,
comprising two distinguished types of information: packet
reports, and report interpretation.
* Packet Reports:
Duffield (Ed.) Expires July 2005 [Page 7]
Internet Draft Packet Selection and Reporting January 2005
Packet Reports comprise a configurable subset of a packet's
input to the Reporting Process, including the packet's
content, information relating to its treatment
(for example, the output interface), and its associated
Selection State (for example, a hash of the packet's
content)
* Report Interpretation:
Report interpretation comprises subsidiary information,
relating to one or more packets, that is used for
interpretation of their Packet Reports. Examples include
configuration parameters of the Selection Process and of the
Reporting Process.
3.5 Measurement Process
* A Measurement Process is the composition of a Selection Process
followed by a Reporting Process.
3.6 Exporting Process
* Exporting Process:
An exporting process sends, in the form of export packet, the
output of one or more Measurement Processes to one or more
collectors.
A Measurement Process may feed more that one Exporting Process.
For example, the output of a Measurement Process may be
exported locally to a measurement application execution at the
observation point, with a copy also being exported to a remote
Collector.
* Export Packets:
a combination of Report Interpretation and/or one or more
Packet Reports are bundled by the Exporting Process into a
export packet for exporting to a collector.
3.7 PSAMP Device
A PSAMP Device is a device hosting at least an Observation Point,
a Measurement Process and an Exporting Process. Typically,
corresponding Observation Point(s), Measurement Process(es) and
Exporting Process(es) are co-located at this device, for example
at a router.
3.8 Collector
Duffield (Ed.) Expires July 2005 [Page 8]
Internet Draft Packet Selection and Reporting January 2005
A collector receives a report stream exported by one or more
Exporting Processes. In some cases, the host of the Measurement
and/or Exporting Processes may also serve as the collector.
3.9 Possible Configurations
Various possibilities for the high level architecture of these
elements are as follows.
MP = Measurement Process, EP = Exporting process
PSAMP Device
+---------------------+ +------------------+
|Observation Point(s) | | Collector(1) |
|MP(s)--->EP----------+---------------->| |
|MP(s)--->EP----------+-------+-------->| |
+---------------------+ | +------------------+
|
PSAMP Device |
+---------------------+ | +------------------+
|Observation Point(s) | +-------->| Collector(2) |
|MP(s)--->EP----------+---------------->| |
+---------------------+ +------------------+
PSAMP Device
+---------------------+
|Observation Point(s) |
|MP(s)--->EP---+ |
| | |
|Collector(3)<-+ |
+---------------------+
The most generic Measurement Process configuration is composed
of:
+------------------------------------+
| +----------+ +---------+ |
| |Selection | | | |
Observed | |Process | Packet |Reporting| |
Packet-->| |(primitive|- Stream ->|Process |--> Report Stream
Stream | | selector)| | | |
| +----------+ +---------+ |
| Measurement Process |
+------------------------------------+
Duffield (Ed.) Expires July 2005 [Page 9]
Internet Draft Packet Selection and Reporting January 2005
A Measurement Process with a composite selector is composed of:
+--------------------------------------------------...
| +-----------------------------------+
| | +----------+ +----------+ |
| | |Selection | |Selection | |
Observed | | |Process | |Process | |
Packet-->| | |(primitive|-Packet->|(primitive|---> Packet ...
Stream | | |selector1)| Stream |selector2)| | Stream
| | +----------+ +----------+ |
| | Composite Selector |
| +-----------------------------------+
| Measurement Process
+--------------------------------------------------...
...-------------+
|
+---------+ |
| | |
|Reporting| |
... | Process |---> Report Stream
| | |
+---------+ |
|
|
|
...-------------+
3.10 PSAMP and IPFIX Interaction
The PSAMP Measurement Process can be viewed as analogous to the
IPFIX metering process. The PSAMP Measurement Process takes an
Observed Packet Stream as its input, and produces Packet Reports
as its output. The IPFIX metering process produces flow records
as its output. The distinct name "Measurement Process" has been
retained in order to avoid potential confusion in settings where
IPFIX and PSAMP coexist, and in order to avoid the implicit
requirement that the PSAMP version satisfy the requirements of an
IPFIX metering process (at least while these are under
development). The relationship between PSAMP and IPFIX is
described more in [PSAMP-INFO].
Duffield (Ed.) Expires July 2005 [Page 10]
Internet Draft Packet Selection and Reporting January 2005
4. Generic Requirements for PSAMP
This section describes the generic requirements for the PSAMP
protocol. A number of these are realized as specific requirements
in later sections.
4.1 Generic Selection Process Requirements.
* Ubiquity: The Selectors must be simple enough to be implemented
ubiquitously at maximal line rate.
* Applicability: the set of Selectors must be rich enough to
support a range of existing and emerging measurement based
applications and protocols. This requires a workable trade-off
between the range of traffic engineering applications and
operational tasks it enables, and the complexity of the set of
capabilities.
* Extensibility: the protocol must be able to accommodate
additional packet selectors not currently defined.
* Flexibility: the protocol must support selection of packets
using various network protocols or encapsulation layers,
including Internet Protocol Version 4 (IPv4) [IPv4], Internet
Protocol Version 6 (IPv6) [RFC-2460], and Multiprotocol Label
Switching (MPLS) [RFC-3031].
* Robust Selection: packet selection must be robust against
attempts to craft an observed packet stream from which packets
are selected disproportionately (e.g. to evade selection, or
overload measurement systems).
* Parallel Measurement Processes: the protocol must support
simultaneous operation of multiple independent Measurement
Processes at the same host.
* Causality: the selection decision for each packet should depend
only weakly, if at all, upon future packets arrivals. This
promotes ubiquity by limiting the complexity of the selection
logic.
* Encrypted Packets: Selectors that interpret packet fields must
be configurable to ignore (i.e. not select) encrypted packets,
when they are detected.
Specific Selectors are outlined in Section 5, and described in
more detail in the companion document [PSAMP-TECH].
4.2 Generic Reporting Process Requirements
* Self-defining: the Report Stream must be complete in the sense
that no additional information need be retrieved from the
Duffield (Ed.) Expires July 2005 [Page 11]
Internet Draft Packet Selection and Reporting January 2005
Observation Point in order to interpret and analyze the
reports.
* Indication of Information Loss: the Report Stream must include
sufficient information to indicate or allow the detection of
loss occurring within the Selection, Reporting or Exporting
Processes, or in transport. This may be achieved by the use of
sequence numbers.
* Accuracy: the Report Stream must include information that
enables the accuracy of measurements to be determined.
* Faithfulness: all reported quantities that relate to the packet
treatment must reflect the router state and configuration
encountered by the packet at the time it is received by the
Measurement Process.
* Privacy: selection of the content of Packet Reports will be
cognizant of privacy and anonymity issues while being
responsive to the needs of measurement applications, and in
accordance with [RFC-2804]. Full packet capture of arbitrary
packet streams is explicitly out of scope.
A specific Reporting Process meeting these requirements, and the
requirement for ubiquity, is described in Section 6.
4.3 Generic Exporting Process Requirements
* Timeliness: configuration must allow for limiting of buffering
delays for the formation and transmission for Export Packets.
See Section 8.4 for further details.
* Congestion Avoidance: export of a Report Stream across a
network must be congestion avoiding in compliance with [RFC-
2914]. This is discussed further in Section 8.2.
* Secure Export:
(i) confidentiality: the option to encrypt exported data must
be provided.
(ii) integrity: alterations in transit to exported data must be
detectable at the Collector
(iii) authenticity: authenticity of exported data must be
verifiable by the Collector in order to detect forged data.
The motivation here is the same as for security in IPFIX export;
see Sections 6.3 and 10 of [RFC-3917].
4.4 Generic Configuration Requirements
Duffield (Ed.) Expires July 2005 [Page 12]
Internet Draft Packet Selection and Reporting January 2005
* Ease of Configuration: of sampling and export parameters, e.g.
for automated remote reconfiguration in response to collected
reports.
* Secure Configuration: the option to configure via protocols
that prevent unauthorized reconfiguration or eavesdropping on
configuration communications must be available. Eavesdropping
on configuration might allow an attacker to gain knowledge that
would be helpful in crafting a packet stream to evade
subversion, or overload the measurement infrastructure.
Configuration is discussed in Section 9. Feasibility and
complexity of PSAMP operations is discussed in Section 10.
5. Packet Selection
This section details specific requirements for the Selection
Process, motivated by the generic requirements of Section 3.3.
5.1 Two Types of Selector
PSAMP categorizes selectors into two types:
* Filtering: a filter is a selector that selects a packet
deterministically based on the Packet Content, the packet's
treatment, and functions of these occurring in the Selection
State. Two examples are:
(i) Field-match filtering.
(ii) Hash-based selection: a hash function is applied to the
packet content, and the packet is selected if the result
falls in a specified range.
* Sampling: a selector that is not a filter is called a sampling
operation. This reflects the intuitive notion that if the
selection of a packet cannot be determined from its content
alone, there must be some type of sampling taking place.
Sampling operations can be divided into two subtypes:
(i) Content-independent Sampling, which does not use Packet
Content in reaching sampling decisions. Examples include
periodic sampling, and uniform pseudorandom sampling driven
by a pseudorandom number whose generation is independent of
packet content. Note that in content-independent sampling it
is not necessary to access the Packet Content in order to
make the selection decision.
(ii) Content-dependent Sampling, in which the Packet Content
is used in reaching selection decisions. An application is
Duffield (Ed.) Expires July 2005 [Page 13]
Internet Draft Packet Selection and Reporting January 2005
pseudorandom selection according to a probability that
depends on the contents of a packet field, e.g., sampling
packets with a probability dependent on their TCP/UDP port
numbers. Note that this is not a Filter.
5.2 PSAMP Packet Selectors
A spectrum of packet selectors is described in detail in [PSAMP-
TECH]. Here we only briefly summarize the meanings for
completeness.
A PSAMP Selection Process must support at least one of the
following Selectors.
* Systematic Time Based Sampling: packet selection is triggered
at periodic instants separated by a time called the spacing.
All packets that arrive within a certain time of the trigger
(called the interval length) are selected.
* Systematic Count Based Sampling: similar to systematic time
based expect that selection is reckoned with respect to packet
count rather than time. Packet selection is triggered
periodically by packet count, a number of successive packets
being selected subsequent to each trigger.
* Uniform Probabilistic Sampling: packets are selected
independently with fixed sampling probability p.
* Non-uniform Probabilistic Sampling: packets are selected
independently with probability p that depends on packet
content.
* Probabilistic n-out-of-N Sampling: from each count-based
successive block of N packets, n are selected at random.
* Field Match Filtering
Filtering schemes are based on the IPFIX flow definition. With
this method a packet is selected if a specific field in the
packet equals a predefined value. Possible filter fields are
all IPFIX flow attributes specified in [IPFIX-INFO]. Further
fields can be defined by vendor specific extensions.
A packet is selected if Field=Value. Masks and ranges are only
supported to the extent to which [IPFIX-INFO] allows them e.g.
by providing explicit fields like the netmasks for source and
destination addresses.
AND operations are possible by concatenating filters, thus
producing a composite selection operation. In this case, the
ordering in which the filtering happens is implicitly defined
(outer filters come after inner filters). However, as long as
Duffield (Ed.) Expires July 2005 [Page 14]
Internet Draft Packet Selection and Reporting January 2005
the concatenation is on filters only, the result of the
cascaded filter is independent from the order, but the order
may be important for implementation purposes, as the first
filter will have to work at a higher rate. In any case, an
implementation is not constrained to respect the filter
ordering, as long as the result is the same, and it may even
implement the composite filtering in filtering in one single
step.
OR operations are not supported with this basic model. More
sophisticated filters (e.g. supporting bitmasks, ranges or OR
operations etc.) can be realized as vendor specific schemes.
Field match operations should be available for different
protocol portions of the packet header:
(i) the IP header (excluding options in IPv4, stacked
headers in IPv6)
(ii) transport header
(iii) encapsulation headers (e.g. the MPLS label stack, if
present)
When the PSAMP device offers field match filtering, and, in its
usual capacity other than in performing PSAMP functions,
identifies or processes information from IP, transport or
encapsulation protocols, then the information should be made
available for filtering. For example, when a PSAMP device
routes based on destination IP address, that field should be
made available for filtering. Conversely, a PSAMP device that
does not route is not expected to be able to locate an IP
address within a packet, or make it available for filtering,
although it may do so.
Since packet encryption alters the meaning of encrypted fields,
field match filtering must be configurable to ignore encrypted
packets, when detected.
* Hash-based Selection: Hash-based selection will employ one or
more hash functions to be standardized. A hash function is
applied to a subset of packet content, and the packet is
selected of the resulting hash falls in a specified range. The
stronger the hash function, the more closely hash-based
selection approximates uniform random sampling. Privacy of hash
selection range and hash function parameters obstructs
subversion of the selector by packets that are crafted either
to avoid selection or to be selected. Privacy of the hash
function is not required. Robustness and security
considerations of hash-based selection are further discussed in
further in [PSAMP-TECH]. Applications of hash-based sampling
are described in Section 11.
Duffield (Ed.) Expires July 2005 [Page 15]
Internet Draft Packet Selection and Reporting January 2005
* Router State Filtering: the Selection Process may support
Filtering based on the following conditions, which may be
combined with the logical AND operator"and", "or" or "not"
operators:
(i) Ingress interface at which packet arrives equals a
specified value
(ii) Egress interface to which packet is routed to equals a
specified value
(iii) Packet violated Access Control List (ACL) on the
router
(iv) Failed Reverse Path Forwarding (RPF)
(v) Failed Resource Reservation (RSVP)
(vi) No route found for the packet
(vii) Origin Border Gateway Protocol (BGP) Autonomous System
(AS) equals a specified value or lies within a given range
(viii) Destination BGP AS equals a specified value or lies
within a given range
Router architectural considerations may preclude some
information concerning the packet treatment being available at
line rate for selection of packets. For example, the Selection
Process may not be implemented in the fast path that is able to
access routing state at line rate. However, when filtering
follows sampling (or some other selection operation) in a
Composite Selector, the rate of the Packet Stream output from
the sampler and input to the filter may be sufficiently slow
that the filter could select based on routing state.
5.3 Selection Fraction Terminology
* Population:
A population is a Packet Stream, or a subset of a Packet
Stream. A Population can be considered as a base set from which
packets are selected. An example is all packets in the Observed
Packet Stream that are observed within some specified time
interval.
* Population Size:
The Population Size is the number of all packets in a
Population.
* Configured Selection Fraction
The Configured Selection Fraction is the ratio of the number of
packets selected by a Selector from an input Population, to the
Duffield (Ed.) Expires July 2005 [Page 16]
Internet Draft Packet Selection and Reporting January 2005
Population Size, as based on the configured selection
parameters.
* Attained Selection Fraction
The Attained Selection Fraction is the actual ratio of the
number of packets selected by a Selector from an input
Population, to the Population Size.
For some sampling methods the Attained Selection Fraction can
differ from the Configured Selection Fraction due to, for
example, the inherent statistical variability in sampling
decisions of probabilistic Sampling and Hash-based Selection.
Nevertheless, for large Population Sizes and properly configured
Selectors, the Attained Selection Fraction usually approaches the
Configured Selection Fraction. In Hash-based Selection, the
Expected Selection Fraction is the quotient of size of the Hash
Selection Range by the size of the Hash Range.
The notions of Configured/Attained Selection Fraction extend
beyond Selectors. An illustrative example is the Configured
Selection Fraction of the composition of the Measurement Process
with the Exporting Process. Here the Population is the Observed
Packet Stream or a subset thereof. The Configured Selection
Fraction is the fraction of the Population for which Packet
Reports which are expected to reach the Collector. This quantity
may reflect additional parameters, not necessarily described in
the PSAMP protocol, that determine the degree of loss suffered by
packet reports en route to the collector, e.g., the transmission
bandwidth available to the Exporting Process. In this example,
the Attained Selection Fraction is the fraction of Population
packets for which reports did actually reach the collector, and
thus incorporates the effect of any loss of Packet Reports due,
e.g, to resource contention at the Observation Point, or during
transmission.
5.4 Input Sequence Numbers for Primitive Selectors
Each instance of a Primitive Selector must maintain a count of
packets presented at its input. The counter value is to be
included as a sequence number for selected packets. The sequence
numbers are considered as part of the packet's Selection State.
Use of input sequence numbers enables applications to determine
the Attained Selection Fraction, and hence correctly normalize
network usage estimates regardless of loss of information,
regardless of whether this loss occurs because of discard of
packet reports in the measurement or reporting process (e.g. due
to resource contention in the host of these processes), or loss
Duffield (Ed.) Expires July 2005 [Page 17]
Internet Draft Packet Selection and Reporting January 2005
of export packets in transmission or collection. See [RFC-3176]
for further details.
As an example, consider a set of n consecutive packet reports r1,
r2,... , rn, selected by a sampling operation and received at a
collector. Let s1, s2,..., sn be the input sequence numbers
reported by the packets. The Attained Selection Fraction for the
composite of the measurement and exporting processes, taking into
account both packet sampling at the observation point and loss in
transmission, is computed as R = (n-1)/(sn-s1). (Note R would be
1 if all packets were selected and there were no transmission
loss).
The Attained Selection Fraction can be used to estimate the
number bytes present in a portion of the Observed Packet Stream.
Let b1, b2,..., bn be the bytes reported in each of the packets
that reached the Collector, and set B = b1+b2+...+bn. Then the
total bytes present in packets in the Observed Packet Stream
whose input sequence numbers lie between s1 and sn is estimated
by B/R, i.e, scaling up the measured bytes through division by
the Attained Selection Fraction
With Composite Selectors, an input sequence number must be
reported for each Selector in the composition.
5.5 Composite Selectors
The ability to compose Selectors in a Selection Process should be
provided. The following combinations appear to be most useful for
applications:
* concatentation of Field Match filters. This is useful for
constructing the AND of the component filters.
* filtering followed by sampling.
* sampling followed by filtering.
Composite Selectors are useful for drill down applications. The
first component of a composite selector can be used to reduce the
load on the second component. In this setting, the advantage to
be gained from a given ordering can depends on the composition of
the packet stream.
5.6 Constraints on the Selection Fraction
Sampling at full line rate, i.e. with probability 1, is not
excluded in principle, although resource constraints may not
permit it in practice.
6. Reporting Process
Duffield (Ed.) Expires July 2005 [Page 18]
Internet Draft Packet Selection and Reporting January 2005
This section details specific requirements for the Reporting
Process, motivated by the generic requirements of Section 3.4
6.1 Mandatory Contents of Packet Reports: Basic Reports
The Reporting Process must include the following in each Packet
Report:
(i) the input sequence number(s) of any Selectors that acted
on the packet in the instance of a Measurement Process of
which the Reporting Process is a component.
(ii) the identifier of the measurement process that produced
the selected packet
The Reporting Process must support inclusion of the following in
each Packet Report, as a configurable option:
(iii) a basic report on the packet, i.e., some number of
contiguous bytes from the start of the packet, including the
packet header (which includes link layer, network layer and
other encapsulation headers) and some subsequent bytes of
the packet payload.
Some devices hosting Reporting Processes may not have the
resource capacity or functionality to provide more detailed
packet reports that those in (i), (ii) and (iii) above. Using
this minimum required reporting functionality, the reporting
process places the burden of interpretation on the Collector, or
on applications that it supplies. Some devices may have the
capability to provide extended packet reports, described in the
next section.
6.2 Extended Packet Reports
The reporting process may support inclusion in Packet Reports of
the following information, inclusion any or all being
configurable as an option.
(iv) fields relating to the following protocols used in the
packet: IPv4, IPV6, transport protocols, MPLS.
(v) packet treatment, including:
- identifiers for any input and output interfaces of the
Observation Point that were traversed by the packet
- source and destination BGP AS
(vi) Selection State associated with the packet, including:
Duffield (Ed.) Expires July 2005 [Page 19]
Internet Draft Packet Selection and Reporting January 2005
- the timestamp of observation of the packet at the
Observation Point. The timestamp should be reported to
microsecond resolution.
- hashes, where calculated.
It is envisaged that selection of fields for Extended Packet
Reporting may be used to reduce reporting bandwidth, in which
case the option to report information in (iii) may not be
exercised.
6.3 Extended Packet Reports in the Presence of IPFIX
If an IPFIX metering process is supported at the Observation
Point, then in order to be PSAMP compliant, Extended Packet
Reports must be able to include all fields required in the IPFIX
information model [IPFIX-INFO], with modifications appropriate to
reporting on single packets rather than flows.
6.4 Report Interpretation
The Report Interpretation must include:
(i) configuration parameters of the Selectors of the packets
reported on.
(ii) format of the Packet Report;
(iii) indication of the inherent accuracy of the reported
quantities, e.g., of the packet timestamp.
The accuracy measure in (iii) is of fundamental importance for
estimating the likely error attached to estimates formed from the
Packet Reports by applications.
Identifiers in (iv) are necessary, e.g., in order to match Packet
Reports to the selection process that selected them. For example,
when Packet Reports produced by a sampling operation suffer loss
(either during export, or in transit) it may be desirable to
reconfigure downwards the Configured Selection Fraction on the
Selection Process that selected them.
The requirements for robustness and transparency are motivations
for including Report Interpretation in the Report Stream: it
makes the Report Stream self-defining. The PSAMP framework
excludes reliance on an alternative model in which interpretation
is recovered out of band. This latter approach is not robust with
respect to undocumented changes in Selector configuration, and
may give rise to future architectural problems for network
Duffield (Ed.) Expires July 2005 [Page 20]
Internet Draft Packet Selection and Reporting January 2005
management systems to coherently manage both configuration and
data collection.
It is not envisaged that all Report Interpretation be included in
every packet report. Many of the quantities listed above are
expected to be relatively static; they could be communicated
periodically, and upon change.
7. Parallel Measurement Processes
Because of the increasing number of distinct measurement
applications, with varying requirements, it is desirable to set
up parallel Measurement Processes on a given Observed Packet
Stream. A device capable of hosting a Measurement Process should
be able to support more than one independently configurable
Measurement Process simultaneously. Each such Measurement Process
should have the option of being equipped with its own Exporting
Process; otherwise the parallel Measurement Processes may share
the same Exporting Process.
Each of the parallel Measurement Processes should be independent.
However, resource constraints may prevent complete reporting on a
packet selected by multiple Selection Processes. In this case,
reporting for the packet must be complete for at least one
Measurement Process; other measurement processes need only record
that they selected the packet, e.g., by incrementing a counter.
The priority amongst Measurement Processes under resource
contention should be configurable.
It is not proposed to standardize the number of parallel
Measurement Processes.
8. Exporting Process
This section detailes specific requirements for the Exporting
Process, motivated by the generic requirements of Section 3.6
8.1 Use of IPFIX
PSAMP will use the IP Flow Information eXport (IPFIX) protocol
for export of the Report Stream. The IPFIX protocol is well
suited for this purpose, because the IPFIX architecture matches
the PSAMP architecture very well and the means provided by the
IPFIX protocol are sufficient for PSAMP purposes. On the other
hand, not all features of the IPFIX protocol will need to be
implemented by some PSAMP devices. For example, a device that
offers only content-independent sampling and basic PSAMP
reporting has no need to support IPFIX capabilities based on
packet fields.
8.1 Export Packets
Duffield (Ed.) Expires July 2005 [Page 21]
Internet Draft Packet Selection and Reporting January 2005
Export packets may contain one or more packet reports, and/or
report interpretation. Export packets must also contain:
(i) An identifier for the Exporting Process
(ii) An export packet sequence number.
An export packet sequence number enables the collector to
identify loss of export packets in transit. Note that some
transport protocols, e.g. UDP, do not provide sequence
numbers. Moreover, having sequence numbers available at the
application level enables the collector to calculate packet
loss rate for use, e.g., in estimating original traffic
volumes from export packet that reach the collector.
8.2 Congestion-aware Unreliable Transport
The export of the report stream does not require reliable export.
Section 5.4 shows that the use of input sequence numbers in
packet Selectors means that the ability to estimate traffic rates
is not impaired by export loss. Export packet loss becomes
another form of sampling, albeit a less desirable, and less
controlled, form of sampling.
In distinction, retransmission of lost Export Packets consumes
additional network resources. The requirement to store
unacknowledged data is an impediment to having ubiquitous support
for PSAMP.
In order to jointly satisfy the timeliness and congestion
avoidance requirements of Section 4.3, a congestion-aware
unreliable transport protocol may be used. IPFIX is compatible
with this requirement, since it mandates support of the Stream
Control Transmission Protocol (SCTP) [SCTP] and the SCTP Partial
Reliability Extension [RFC-3758].
IPFIX also allows the use of User Datagram Protocol (UDP) [RFC-
768] although it is not a congestion-aware protocol. However, in
this case, the Export Packets must remain wholly within the
administrative domains of the operators [IPFIX-PROTO]. The PSAMP
exporting process is equipped with a configurable export rate
limit (see Section 8.3 following) that can be used to limit the
export rate when a congestion aware transport protocol is not
used. The collector, upon detection of export packet loss through
missing export sequence numbers, may reconfigure the export rate
limit downwards in order to avoid congestion.
8.3 Configurable Export Rate Limit
The exporting process must have an export rate limit,
configurable per Exporting Process. This is useful for two
reasons:
Duffield (Ed.) Expires July 2005 [Page 22]
Internet Draft Packet Selection and Reporting January 2005
(i) Even without network congestion, the rate of packet
selection may exceed the capacity of the Collector to
process reports, particularly when many Exporting Processes
feed a common Collector. Use of an Export Rate Limit allows
control of the global input rate to the Collector.
(ii) IPFIX provides export using UDP as the transport
protocol in some circumstances. An Export Rate Limit allows
the capping of the export rate to match both path link
speeds and the capacity of the Collector.
8.4 Limiting Delay for Export Packets
Low measurement latency allows the traffic monitoring system to
be more responsive to real-time network events, for example, in
quickly identifying sources of congestion. Timeliness is
generally a good thing for devices performing the sampling since
it minimizes the amount of memory needed to buffer samples.
Keeping the packet dispatching delay small has other benefits
besides limiting buffer requirements. For many applications a
resolution of 1 second is sufficient. Applications in this
category would include: identifying sources associated with
congestion, tracing denial of service attacks through the
network, and constructing traffic matrices. Furthermore, keeping
dispatch delay within the resolution required by applications
eliminates the need for timestamping by synchronized clocks at
observation points, or for the Observation Points and Collector
to maintain bi-directional communication in order to track clock
offsets. The collector can simply process Packet Reports in the
order that they are received, using its own clock as a "global"
time base. This avoids the complexity of buffering and reordering
samples. See [DuGeGr02] for an example.
The delay between observation of a packet and transmission of a
Export Packet containing a report on that packet has several
components. It is difficult to standardize a given numerical
delay requirement, since in practice the delay may be sensitive
to processor load at the Observation Point. Therefore, PSAMP aims
to control that portion of the delay within the Observation Point
that is due to buffering in the formation and transmission of
Export Packets.
In order to limit delay in the formation of Export Packets, the
Exporting Process must provide the ability to close out and
enqueue for transmission any Export Packet during formation as
soon as it includes one Packet Report.
In order to limit the delay in the transmission of Export
Packets, a configurable upper bound to the delay of an Export
Packet prior to transmission must be provided. If the bound is
Duffield (Ed.) Expires July 2005 [Page 23]
Internet Draft Packet Selection and Reporting January 2005
exceeded the Export Packet is dropped. This functionality can be
provided by the timed reliability service of the SCTP Partial
Reliability Extension [RFC-3758].
The Exporting Process may enqueue the Report Stream in order to
export multiple Packet Reports in a single export packet. Any
consequent delay must still allow for timely availability of
Packet Reports as just described. The timed reliability service
of the SCTP Partial Reliability Extension [RFC-3758] allows the
dropping of packets from the export buffer once their age in the
buffer exceeds a configurable bound. A suitable default value for
the bound should be used in order to avoid a low transmission
rate due to misconfiguration.
8.5 Export Packet Compression
To conserve network bandwidth and resources at the Collector, the
Export Packets may be compressed before export. Compression is
expected to be quite effective since the sampled packets may
share many fields in common, e.g. if a filter focuses on packets
with certain values in particular header fields. Using
compression, however, could impact the timeliness of Packet
Reports. Any consequent delay must not violate the timeliness
requirement for availability of Packet Reports at the collector.
8.6 Collector Destination
When exporting to a remote Collector, the Collector is identified
by IP address, transport protocol, and transport port number.
8.7 Local Export
The Report Stream may be directly exported to on-board
measurement based applications, for example those that form
composite statistics from more than one packet. Local export may
be presented through an interface direct to the higher level
applications, i.e., through an API, rather than employing the
transport used for off-board export. Specification of such an API
is outside the scope of the PSAMP framework.
A possible example of Local Export could be that packets selected
by the PSAMP measurement process serve as the input for the IPFIX
protocol, which then forms flow records out of the stream of
selected packets.
9. Configuration and Management
A key requirement for PSAMP is the easy reconfiguration of the
parameters of the Measurement Process: those for selection,
packet reports and export. An important example is to support
measurement-based applications that want to adaptively drill-down
Duffield (Ed.) Expires July 2005 [Page 24]
Internet Draft Packet Selection and Reporting January 2005
on traffic detail in real-time;
To facilitate reconfiguration and retrieval of parameters, they
are to reside in a Management Information Base (MIB). Mandatory
configuration, capabilities and monitoring objects will cover all
mandatory PSAMP functionality.
Secondary objects will cover the recommended and optional PSAMP
functionality, and must be provided when such functionality is
offered by a PSAMP device. Such PSAMP functionality includes
configuration of offered Selectors, multiple Measurement
Processes, and report format including the choice of fields to be
reported. For further details concerning the PSAMP MIB, see
[PSAMP-MIB].
PSAMP requires a uniform mechanism with which to access and
configure the MIB. SNMP access must be provided by the host of
the MIB.
10. Feasibility and Complexity
In order for PSAMP to be supported across the entire spectrum of
networking equipment, it must be simple and inexpensive to
implement. One can envision easy-to-implement instances of the
mechanisms described within this draft. Thus, for that subset of
instances, it should be straightforward for virtually all system
vendors to include them within their products. Indeed, sampling
and filtering operations are already realized in available
equipment.
Here we give some specific arguments to demonstrate feasibility
and comment on the complexity of hardware implementations. We
stress here that the point of these arguments is not to favor or
recommend any particular implementation, or to suggest a path for
standardization, but rather to demonstrate that the set of
possible implementations is not empty.
10.1 Feasibility
10.1.1 Filtering
Filtering consists of a small number of mask (bit-wise logical),
comparison and range (greater than) operations. Implementation
of at least a small number of such operations is straightforward.
For example, filters for security access control lists (ACLs) are
widely implemented. This could be as simple as an exact match on
certain fields, or involve more complex comparisons and ranges.
10.1.2 Sampling
Sampling based on either counters (counter set, decrement, test
for equal to zero) or range matching on the hash of a packet
Duffield (Ed.) Expires July 2005 [Page 25]
Internet Draft Packet Selection and Reporting January 2005
(greater than) is possible given a small number of selectors,
although there may be some differences in ease of implementation
for hardware vs. software platforms.
10.1.3 Hashing
Hashing functions vary greatly in complexity. Execution of a
small number of sufficient simple hash functions is implementable
at line rate. Concerning the input to the hash function,
hop-invariant IP header fields (IP address, IP identification)
and TCP/UDP header fields (port numbers, TCP sequence number)
drawn from the first 40 bytes of the packet have been found to
possess a considerable variability; see [DuGr01].
10.1.4 Reporting
The simplest packet report would duplicate the first n bytes of
the packet. However, such an uncompressed format may tax the
bandwidth available to the reporting process for high sampling
rates; reporting selected fields would save on this bandwidth.
Thus there is a trade-off between simplicity and bandwidth
limitations.
10.1.5 Exporting
Ease of exporting export packets depends on the system
architecture. Most systems should be able to support export by
insertion of export packets, even through the software path.
10.2 Potential Hardware Complexity
We now comment on the complexity of possible hardware
implementations. Achieving low constants for performance while
minimizing hardware resources is, of course, a challenge,
especially at very high clock frequencies. Most of the selectors,
however, are very basic and their implementations very well
understood; in fact, the average ASIC designer simply uses canned
library instances of these operations rather than design them
from scratch. In addition, networking equipment generally does
not need to run at the fastest clock rates, further reducing the
effort required to get reasonably efficient implementations.
Simple bit-wise logical operations are easy to implement in
hardware. Such operations (NAND/NOR/XNOR/NOT) directly translate
to four-transistor gates. Each bit of a multiple-bit logical
operation is completely independent and thus can be performed in
parallel incurring no additional performance cost above a single
bit operation.
Comparisons (EQ/NEQ) take O(log(M)) stages of logic, where M is
the number of bits involved in the comparison. The log(M) is
required to accumulate the result into a single bit.
Duffield (Ed.) Expires July 2005 [Page 26]
Internet Draft Packet Selection and Reporting January 2005
Greater than operations, as used to determine whether a hash
falls in a selection range, are a determination of the most
significant not-equivalent bit in the two operands. The operand
with that most-significant-not-equal bit set to be one is greater
than the other. Thus, a greater than operation is also an
O(log(M)) stages of logic operation. Optimized implementations of
arithmetic operations are also O(log(M)) due to propagation of
the carry bit.
Setting a counter is simply loading a register with a state. Such
an operation is simple and fast O(1). Incrementing or
decrementing a counter is a read, followed by an arithmetic
operation followed by a store. Making the register dual-ported
does take additional space, but it is a well-understood
technique. Thus, the increment/decrement is also an O(log(M))
operation.
Hashing functions come in a variety of forms. The computation
involved in a standard Cyclic Redundancy Code (CRC) for example
are essentially a set of XOR operations, where the intermediate
result is stored and XORed with the next chunk of data. There
are only O(1) operations and no log complexity operations. Thus,
a simple hash function, such as CRC or generalizations thereof,
can be implemented in hardware very efficiently.
At the other end of the range of complexity, the MD5 function
uses a large number of bit-wise conditional operations and
arithmetic operations. The former are O(1) operations and the
latter are O(log(M)). MD5 specifies 256 32b ADD operations per
16B of input processed. Consider processing 10Gb/sec at 100MHz
(this processing rate appears to be currently available). This
requires processing 12.5B/cycle, and hence at least 200 adders, a
sizeable number. Because of data dependencies within the MD5
algorithm, the adders cannot be simply run in parallel, thus
requiring either faster clock rates and/or more advanced
architectures. Thus, selection hashing functions as complex as
MD5 may be precluded for ubiquitous use at full line rate. This
motivates exploring the use of selection hash functions with
complexity somewhere between that of MD5 and CRC. In some
applications (see Section below) a second hash may be calculated
on only selected packets; MD5 is feasible for this purpose if the
rate of production of selected packets is sufficiently low.
11. Applications
We first describe several representative operational applications
that require traffic measurements at various levels of temporal
and spatial granularity. Some of the goals here appear similar to
those of IPFIX, at least in the broad classes of applications
supported. The major benefit of PSAMP is the support of new
Duffield (Ed.) Expires July 2005 [Page 27]
Internet Draft Packet Selection and Reporting January 2005
network management applications, specifically, those enabled by
the packet selectors that it supports.
11.1 Baseline Measurement and Drill Down
Packet sampling is ideally suited to determine the composition of
the traffic across a network. The approach is to enable
measurement on a cut-set of the network links such that each
packet entering the network is seen at least once, for example,
on all ingress links. Unfiltered sampling with a relatively low
selection fraction establishes baseline measurements of the
network traffic. Packet reports include packet attributes of
common interest: source and destination address and port numbers,
prefix, protocol number, type of service, etc. Traffic matrices
are indicated by reporting source and destination AS matrices.
Absolute traffic volumes are estimated by renormalizing the
sampled traffic volumes through division by either the Configured
Selection Fraction, or by the Attained Selection Fraction (as
derived from input packet counters included in the report stream)
Suppose an operator or a measurement-based application detects an
interesting subset of a packet stream, as identified by a
particular packet attribute. Real-time drill-down to that subset
is achieved by instantiating a new Measurement Process on the
same Observed Packet Stream from which the subset was reported.
The Selection Process of the new Measurement Process filters
according to the attribute of interest, and composes with
sampling if necessary to manage the attained fraction of packets
selected.
11.2 Trajectory Sampling
The goal of trajectory sampling is the selection of a subset of
packets at all enabled Observation Points at which they are
observed in a network domain. Thus the selection decisions are
consistent in the sense that each packet is selected either at
all enabled Observation Points, or at none of them. Trajectory
sampling is realized by hash-based selection if all enabled
Observation Points apply a common hash function to a portion of
the packet content that is invariant along the packet path.
(Thus, fields such at TTL and CRC are excluded).
The trajectory followed by a packet is reconstructed from packet
reports on it that reach the collector. Reports on a given packet
are associated either by matching a label comprising the
invariant reported packet content, or possibly some digest of it.
The reconstruction of trajectories, and methods for dealing with
possible ambiguities due to label collisions (identical labels
reported by different packets) and potential loss of reports in
transmission are dealt with in [DuGr01], [DuGeGr02] and [DuGr04].
Duffield (Ed.) Expires July 2005 [Page 28]
Internet Draft Packet Selection and Reporting January 2005
11.3 Passive Performance Measurement
Trajectory sampling enables the tracking of the performance
experience by customer traffic, customers identified by a list of
source or destination prefixes, or by ingress or egress
interfaces. Operational uses include the verification of Service
Level Agreements (SLAs), and troubleshooting following a customer
complaint.
In this application, trajectory sampling is enabled at all
network ingress and egress interfaces. Rates of loss in transit
between ingress and egress are estimated from the proportion of
trajectories for which no egress report is received. Note that
loss of customer packets is distinguishable from loss of packet
reports through use of report sequence numbers. Assuming
synchronization of clocks between different entities, delay of
customer traffic across the network may also be measured; see
[Zs02].
Extending hash-selection to all interfaces in the network would
enable attribution of poor performance to individual network
links.
11.4 Troubleshooting
PSAMP Packet Reports can also be used to diagnose problems whose
occurrence is evident from aggregate statistics, per interface
utilization and packet loss statistics. These statistics are
typically moving averages over relatively long time windows,
e.g., 5 minutes, and serve as a coarse-grain indication of
operational health of the network. The most common method of
obtaining such measurements are through the appropriate SNMP MIBs
(MIB-II [RFC-1213] and vendor-specific MIBs.)
Suppose an operator detects a link that is persistently
overloaded and experiences significant packet drop rates. There
is a wide range of potential causes: routing parameters (e.g.,
OSPF link weights) that are poorly adapted to the traffic matrix,
e.g., because of a shift in that matrix; a denial of service
attack or a flash crowd; a routing problem (link flapping). In
most cases, aggregate link statistics are not sufficient to
distinguish between such causes, and to decide on an appropriate
corrective action. For example, if routing over two links is
unstable, and the links flap between being overloaded and
inactive, this might be averaged out in a 5 minute window,
indicating moderate loads on both links.
Baseline PSAMP measurement of the congested link, as described in
Section 11.1, enables measurements that are fine grained in both
space and time. The operator has to be able to determine how many
bytes/packets are generated for each source/destination address,
Duffield (Ed.) Expires July 2005 [Page 29]
Internet Draft Packet Selection and Reporting January 2005
port number, and prefix, or other attributes, such as protocol
number, MPLS forwarding equivalence class (FEC), type of service,
etc. This allows the precise determination of the nature of the
offending traffic. For example, in the case of a Distributed
Denial of Service(DDoS) attack, the operator would see a
significant fraction of traffic with an identical destination
address.
In certain circumstances, precise information about the spatial
flow of traffic through the network domain is required to detect
and diagnose problems and verify correct network behavior. In the
case of the overloaded link, it would be very helpful to know the
precise set of paths that packets traversing this link follow.
This would readily reveal a routing problem such as a loop, or a
link with a misconfigured weight. More generally, complex
diagnosis scenarios can benefit from measurement of traffic
intensities (and other attributes) over a set of paths that is
constrained in some way. For example, if a multihomed customer
complains about performance problems on one of the access links
from a particular source address prefix, the operator should be
able to examine in detail the traffic from that source prefix
which also traverses the specified access link towards the
customer.
While it is in principle possible to obtain the spatial flow of
traffic through auxiliary network state information, e.g., by
downloading routing and forwarding tables from routers, this
information is often unreliable, outdated, voluminous, and
contingent on a network model. For operational purposes, a direct
observation of traffic flow provided by trajectory sampling is
more reliable, as it does not depend on any such auxiliary
information. For example, if there was a bug in a router's
software, direct observation would allow the diagnosis the effect
of this bug, while an indirect method would not.
12. Security Considerations
Security considerations are addressed in:
- Section 4.1: item Robust Selection
- Section 4.3: item Secure Export
- Section 4.4: item Secure Configuration
13. IANA Considerations
This document has no actions for IANA
14. Normative References
[PSAMP-TECH] T. Zseby, M. Molina, F. Raspall, N. G. Duffield,
S. Niccolini, Sampling and Filtering Techniques for IP
Packet Selection, RFC XXXX. [Currently Internet Draft,
Duffield (Ed.) Expires July 2005 [Page 30]
Internet Draft Packet Selection and Reporting January 2005
draft-ietf-psamp-sample-tech-05.txt, work in progress,
October 2004.
[PSAMP-MIB] T. Dietz, B. Claise, Definitions of Managed
Objects for Packet Sampling, RFC XXXX. [Currently
Internet Draft, draft-ietf-psamp-mib-03.txt, work in
progress, July 2004.]
[PSAMP-PROTO] B. Claise (Ed.) Packet Sampling (PSAMP)
Protocol Specifications, RFC XXXX. [Currently Internet
Draft draft-ietf-psamp-protocol-01.txt, work in progress,
February 2004.]
[PSAMP-INFO] T. Dietz, F. Dressler, G. Carle, B. Claise,
Information Model for Packet Sampling Exports, RFC XXXX.
[Currently Internet Draft, draft-ietf-psamp-info-02, July
2004
[IPFIX-PROTO] B. Claise (Ed.) IPFIX Protocol
Specifications , Internet Draft,
draft-ietf-ipfix-protocol-06.txt, October 2004.
[IPFIX-INFO] J. Meyer, J. Quittek, S. Bryant, "Information
Model for IP Flow Information Export"
draft-ietf-ipfix-info-06, October 2004
[RFC-2960] R. Stewart, (ed.) "Stream Control Transmission
Protocol", RFC 2960, October 2000.
[RFC-3758] R. Stewart, M. Ramalho, Q. Xie, M. Tuexen, P.
Conrad, "SCTP Partial Reliability Extension", RFC 3758,
May 2004.
15. Informative References
[B88] R.T. Braden, A pseudo-machine for packet monitoring
and statistics, in Proc ACM SIGCOMM 1988
[ClPB93] K.C. Claffy, G.C. Polyzos, H.-W. Braun, Application
of Sampling Methodologies to Network Traffic
Characterization, Proceedings of ACM SIGCOMM'93, San
Francisco, CA, USA, September 13-17, 1993
[RFC-2460] S. Deering, R. Hinden, Internet Protocol, Version
6 (IPv6) Specification, RFC 2460, December 1998.
[DuGr01] N. G. Duffield and M. Grossglauser, Trajectory
Sampling for Direct Traffic Observation, IEEE/ACM Trans.
on Networking, 9(3), 280-292, June 2001.
Duffield (Ed.) Expires July 2005 [Page 31]
Internet Draft Packet Selection and Reporting January 2005
[DuGeGr02] N.G. Duffield, A. Gerber, M. Grossglauser,
Trajectory Engine: A Backend for Trajectory Sampling,
IEEE Network Operations and Management Symposium 2002,
Florence, Italy, April 15-19, 2002.
[DuGr04] N. G. Duffield and M. Grossglauser, Trajectory
Sampling with Unreliable Reporting, Proc IEEE Infocom
2004, Hong Kong, March 2004,
[RFC-2914] S. Floyd, Congestion Control Principles, RFC
2914, September 2000.
[RFC-2804] IAB and IESG, Network Working Group, IETF Policy
on Wiretapping, RFC 2804, May 2000
[RFC-1213] K. McCloghrie, M. Rose, Management Information
Base for Network Management of TCP/IP-based
internets:MIB-II, RFC 1213, March 1991.
[RFC-3176] P. Phaal, S. Panchen, N. McKee, InMon
Corporation's sFlow: A Method for Monitoring Traffic in
Switched and Routed Networks, RFC 3176, September 2001
[RFC-2330] V. Paxson, G. Almes, J. Mahdavi, M. Mathis,
Framework for IP Performance Metrics, RFC 2330, May 1998
[RFC-791] J. Postel, "Internet Protocol", STD 5, RFC 791,
September 1981.
[RFC-768] Postel, J., "User Datagram Protocol" RFC 768,
August 1980
[RFC-3917] J. Quittek, T. Zseby, B. Claise, S. Zander,
Requirements for IP Flow Information Export, RFC 3917,
October 2004.
[RFC-1771] Rekhter, Y. and T. Li, "A Border Gateway
Protocol 4 (BGP-4)", RFC 1771, March 1995.
[RFC-3031] Rosen, E., Viswanathan, A. and R. Callon,
"Multiprotocol Label Switching Architecture", RFC 3031,
January 2001.
[SPSJTKS01] A. C. Snoeren, C. Partridge, L. A. Sanchez, C.
E. Jones, F. Tchakountio, S. T. Kent, W. T. Strayer,
Hash-Based IP Traceback, Proc. ACM SIGCOMM 2001, San
Diego, CA, September 2001.
[Zs02] T. Zseby, ``Deployment of Sampling Methods for SLA
Validation with Non-Intrusive Measurements'', Proceedings
Duffield (Ed.) Expires July 2005 [Page 32]
Internet Draft Packet Selection and Reporting January 2005
of Passive and Active Measurement Workshop (PAM 2002),
Fort Collins, CO, USA, March 25-26, 2002
16. Authors' Addresses
Derek Chiou
Avici Systems
101 Billerica Ave
North Billerica, MA 01862
Phone: +1 978-964-2017
Email: dchiou@avici.com
Benoit Claise
Cisco Systems
De Kleetlaan 6a b1
1831 Diegem
Belgium
Phone: +32 2 704 5622
Email: bclaise@cisco.com
Nick Duffield
AT&T Labs - Research
Room B139
180 Park Ave
Florham Park NJ 07932, USA
Phone: +1 973-360-8726
Email: duffield@research.att.com
Albert Greenberg
AT&T Labs - Research
Room A161
180 Park Ave
Florham Park NJ 07932, USA
Phone: +1 973-360-8730
Email: albert@research.att.com
Matthias Grossglauser
School of Computer and Communication Sciences
EPFL
1015 Lausanne
Switzerland
Email: matthias.grossglauser@epfl.ch
Peram Marimuthu
Cisco Systems
170, W. Tasman Drive
San Jose, CA 95134
Phone: (408) 527-6314
Email: peram@cisco.com
Jennifer Rexford
AT&T Labs - Research
Duffield (Ed.) Expires July 2005 [Page 33]
Internet Draft Packet Selection and Reporting January 2005
Room A139
180 Park Ave
Florham Park NJ 07932, USA
Phone: +1 973-360-8728
Email: jrex@research.att.com
Ganesh Sadasivan
Cisco Systems
170 W. Tasman Drive
San Jose, CA 95134
Phone: (408) 527-0251
Email: gsadasiv@cisco.com
17. Intellectual Property Statements
By submitting this Internet-Draft, each author represents that
any applicable patent or other IPR claims of which he or she is
aware have been or will be disclosed, and any of which he or she
becomes aware will be disclosed, in accordance with Section 6 of
RFC 3668.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the
use of such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR
repository at http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention
any copyrights, patents or patent applications, or other
proprietary rights that may cover technology that may be required
to implement this standard. Please address the information to
the IETF at ietf-ipr@ietf.org.
The IETF has been notified by AT&T Corp. of intellectual property
rights claimed in regard to some or all of the specification
contained in this document. For more information, see
http://www.ietf.org/ietf/IPR/att-ipr-draft-ietf-psamp-
framework.txt
The IETF has been notified by Cisco Corp. of intellectual
property rights claimed in regard to some or all of the
specification contained in this document. For more information,
see
http://www.ietf.org/ietf/IPR/cisco-ipr-draft-ietf-psamp-
framework-06.txt
18. Full Copyright Statement
Copyright (C) The Internet Society (2004). This document is
subject to the rights, licenses and restrictions contained in BCP
Duffield (Ed.) Expires July 2005 [Page 34]
Internet Draft Packet Selection and Reporting January 2005
78 and except as set forth therein, the authors retain all their
rights.
This document and translations of it may be copied and furnished
to others, and derivative works that comment on or otherwise
explain it or assist in its implementation may be prepared,
copied, published and distributed, in whole or in part, without
restriction of any kind, provided that the above copyright notice
and this paragraph are included on all such copies and derivative
works. However, this document itself may not be modified in any
way, such as by removing the copyright notice or references to
the Internet Society or other Internet organizations, except as
needed for the purpose of developing Internet standards in which
case the procedures for copyrights defined in the Internet
Standards process must be followed, or as required to translate
it into languages other than English.
The limited permissions granted above are perpetual and will not
be revoked by the Internet Society or its successors or assigns.
19. Disclaimers
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be
claimed to pertain to the implementation or use of the technology
described in this document or the extent to which any license
under such rights might or might not be available; nor does it
represent that it has made any independent effort to identify any
such rights. Information on the procedures with respect to
rights in RFC documents can be found in BCP 78 and BCP 79.
This document and the information contained herein are provided
on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE
REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY
THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY
RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE.
Duffield (Ed.) Expires July 2005 [Page 35]
| PAFTECH AB 2003-2026 | 2026-04-22 23:48:52 |