One document matched: draft-ietf-pcn-signaling-requirements-00.txt
Internet Engineering Task Force G. Karagiannis
Internet-Draft University of Twente
Intended status: Informational T. Taylor
Expires: January 5, 2011 K. Chan
Huawei Technologies
M. Menth
University of Wurzburg
July 5, 2010
Requirements for Signaling of (Pre-) Congestion Information in a
DiffServ Domain
draft-ietf-pcn-signaling-requirements-00
Abstract
Precongestion notification (PCN) is a means for protecting quality of
service for inelastic traffic admitted to a Diffserv domain. The
overall PCN architecture is described in RFC 5559. This memo
describes the requirements for the signaling applied within the PCN
domain: PCN feedback is carried from the PCN-egress-node to the
decision point and the decision point may demand for the measurement
and delivery of the PCN rate sent at the PCN-ingress-node. The
decision point may be either collocated with the PCN-ingress-node or
a centralized node.
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on January 5, 2011.
Karagiannis, et al. Expires January 5, 2011 [Page 1]
Internet-Draft PCN Signaling requirements July 2010
Copyright Notice
Copyright (c) 2010 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the BSD License.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 3
2. Signaling requirements between PCN-egress-nodes and
Decision Point . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 PCN Reporting Frequency . . . . . . . . .. . . . . . . . . . . 4
2.2 Signaled PCN egress Feedback . . . . . . .. . . . . . . . . . .5
2.3 Signaling requirements . . . . . . . . . .. . . . . . . . . . .5
2.3.1 Priority of signaling messages . . . . . . . . . . . . . . 5
2.3.2 Local information exchange. . . . . . . . . . . . . . . . .5
2.3.3 Carry identification of PCN edge nodes . . . . . . . . . .5
2.3.4 Carry identification of ingress-egress-aggregates . . . . 6
2.3.5 Signaling load. . . . . . .. . . . . . . . . . . . . . . . 6
2.3.6 Reliability. . . . . . .. . . . . . . . . . . . . . . . . 6
2.3.7 Security. . . . . . .. . . . . . . . . . . . . . . . . . 6
2.4. Filter specifications . . . . . . . . . . . . . . . . . . . . 6
3. Signaling Requirements between Decision Point and
PCN-ingress-nodes . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1 Signaled PCN ingress Feedback. . . . . . . . . . . . . . . . . 7
3.2 Signaled decision point trigger. . . . . . . . . . . . . . . . 7
3.3 Signaling requirements . . . . . . . . . .. . . . . . . . . . .7
4. Security Considerations . . . . . . . . . . . . . . . . . . . . . 8
5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . . . 8
6. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . . 8
7. References . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
7.1. Normative References . . . . . . . . . . . . . . . . . . . . 8
7.2. Informative References . . . . . . . . . . . . . . . . . . . 8
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 9
Karagiannis, et al. Expires January 5, 2011 [Page 2]
Internet-Draft PCN Signaling requirements July 2010
1. Introduction
The main objective of Pre-Congestion Notification (PCN) is to support
the quality of service (QoS) of inelastic flows within a Diffserv
domain in a simple, scalable, and robust fashion. Two mechanisms
are used: admission control and flow termination. Admission control
is used to decide whether to admit or block a new flow request while
flow termination is used in abnormal circumstances to decide
whether to terminate some of the existing flows. To support these
two features, the overall rate of PCN-traffic is metered on every
link in the domain, and PCN-packets are appropriately marked when
certain configured rates are exceeded. These configured rates are
below the rate of the link thus providing notification to boundary
nodes about overloads before any congestion occurs (hence "pre-
congestion" notification). The PCN-egress-nodes measure the rates of
differently marked PCN traffic in periodic intervals and report these
rates as so-called PCN feedback to the decision points for admission
control and flow termination based on which they take their
decisions.The decision points may be collocated with the PCN-ingress-
nodes or their function may be implemented in a centralized node.
For more details see[RFC5559, [draft-ietf-pcn-cl-edge-behaviour-06],
[draft-ietf-pcn-sm-edge-behaviour-03].
Thus, signaling is needed to transport PCN feedback from PCN-egress-
nodes towards the decision point. Moreover, signaling is needed that
the decision point can trigger the PCN-ingress-node to measure the
PCN traffic rate and send these measurement results to the decision
point.
This memo briefly describes the signaled content and specifies the
requirements that have to be satisfied by the signaling protocols.
1.1. Terminology
In addition to the terms defined in [RFC5559], this document uses the
following terms:
Decision Point:
The node that makes the decision about which flows to admit and to
terminate. In a given network deployment, this may be the ingress
node or a centralized control node. Of course, regardless of the
location of the decision point, the ingress node is the point
where the decisions are enforced.
Karagiannis, et al. Expires January 5, 2011 [Page 3]
Internet-Draft PCN Signaling requirements July 2010
PCN egress feedback:
Content used by the PCN-egress-node to report and inform the
decision point about measurements required during flow
admission and flow termination decisions.
PCN ingress feedback:
Content used by the PCN-ingress-node to report and inform the
decision point about measurements required during flow termination
decisions.
ingress rate request:
A message sent by the decision point towards the PCN-ingress-node
to request the PCN-ingress-node to measure and report the value of
the rate of admitted PCN traffic for a given
ingress-egress-aggregate.
Congestion level estimate (CLE)
A value derived from the measurement of PCN packets calculated at a
PCN-egress-node for a given ingress-egress-aggregate, representing
the ratio of marked to total PCN traffic (measured in octets) over
a short period. For further details see
[draft-ietf-pcn-cl-edge-behaviour-06] and [draft-ietf-pcn-sm-edge-
behaviour-03].
2. Signaling requirements between PCN-egress-nodes and
Decision Point
The PCN-egress-node measures the rates of differently marked PCN
traffic in regular intervals and signals them as PCN egress feedback
to the decision point.
This section describes the PCN egress feedback and the requirements
that apply to signaling protocols used for the transport of PCN
feedback from PCN-egress-nodes to decision points.
Note that if the decision point and the PCN-ingress-node are
collocated, then the signaling requirements described in this section
apply to the signaling between PCN-egress-nodes and PCN-ingress-
nodes.
2.1 PCN Reporting Frequency
The specification of PCN-based admission control and flow termination
in [draft-ietf-pcn-cl-edge-behaviour-06], [draft-ietf-pcn-sm-edge-
behaviour-03] suggest measurement and reporting intervals at the PCN-
egress-nodes of 100 to 500 ms. The PCN reporting frequency can provide
some level of reliability. Therefore, it is considered that for regularly
reported information, additional reliability mechanisms are not needed,
see Section 2.3.6. The following PCN contents are sent regularly: rate of
not-marked PCN traffic, rate of threshold-marked PCN
traffic, rate of excess-traffic-marked PCN traffic, CLE.
Karagiannis, et al. Expires January 5, 2011 [Page 4]
Internet-Draft PCN Signaling requirements July 2010
2.2 Signaled PCN egress Feedback
The PCN-egress-node measures per ingress-egress-aggregate the
following rates
o rate of not-marked PCN traffic;
o rate of threshold-marked PCN traffic, which applies to CL edge
behaviour only;
o rate of excess-traffic-marked PCN traffic.
o Congestion level estimate (CLE)
The rate values are reported in octets/second to the decision point each
time that the PCN-egress-node calculates them and when this is supported
via configuration. CLE is only reported to the decision point when this
is supported via configuration.
For more details see [draft-ietf-pcn-cl-edge-behaviour-06], [draft-ietf-
pcn-sm-edge-behaviour-03].
If multipath routing is enabled, the PCN-egress-node tracks a list of
flows for which it has recently received excess-traffic-marked
packets. The list of these flow IDs is included in the PCN feedback
because these flows are candidates for termination.
The representation of a flow ID depends on the surrounding
environment, e.g., "pure IP", MPLS, GMPLS, etc. Examples of such flow ID
representations can be found in [RFC2205], [RFC3175] [RFC3209],
[RFC3473]. The list SHOULD be a concatenation of flow IDs associated with
the flows that are candidates for termination. The format of a list
containing flow ID_1 to flow ID_n SHOULD be:
list flow IDs = <flow ID_1> <flow ID_2> ... <flow_ID_n>.
2.3 Signaling requirements
This section describes the requirements for signaling protocols that
are used to carry the PCN egress feedback from PCN-egress-nodes to
the decision point.
2.3.1 Priority of signaling messages
Signaling messages SHOULD have a higher priority than data packets.
This is needed to avoid as much as possible the situations that
during severe overload cases the signaling messages are dropped
within the PCN domain.
2.3.2 Local information exchange
Signaling messages MUST be able to carry the PCN egress feedback from
the PCN-egress-node to the decision point.
2.3.3 Carry identification of PCN edge nodes
The signaling protocol MUST be able to carry identification
(address information) of the PCN edge nodes. This is required due to the
fact that the decision point needs to be able to associate the received
signaling message with the PCN edge node that sent this message.
Karagiannis, et al. Expires January 5, 2011 [Page 5]
Internet-Draft PCN Signaling requirements July 2010
However, the identification of the PCN edge nodes
MUST NOT be visible to non-PCN nodes outside the PCN domain.
2.3.4 Carry identification of ingress-egress-aggregates
The signaling protocol MUST be able to carry identification
(address information) of the ingress-egress-aggregates. It is
proposed to identify them using the addresses of the PCN-ingress-node
and PCN-egress-node between which they pass. If each of the edge
nodes do not have unique addresses, then other identifiers could be
used.
2.3.5 Signaling load
The load generated by the signaling protocol to carry the PCN egress
Feedback from the PCN-egress-nodes to the decision point SHOULD be
minimized as much as possible.
2.3.6 Reliability
There are situations that messages need to be received in a
reliable way. There are different ways of achieving reliability. The
solution of achieving this reliability is out of the scope of this
document. However, it is considered that when information is received on
a regular fashion, additional reliability measures are not
required. The list with flow IDs associated with the excess-traffic-
marked flows is not sent regularly, hence SHOULD be sent reliably.
2.3.7 Security
The signaling support may need security protection against replay
attacks. The security services to be supported are:
o) Message authentication and integrity: an attacker could cause denial
of service using impersonation. Moreover, an attacker could cause a
denial of service by modifying message contents. Therefore, message
authentication and integrity SHOULD be supported.
o) Message confidentiality: There could be situations where the PCN
signaling messages should not be visible to non authorised nodes. In
such cases, PCN message confidentiality MAY be supported.
2.4. Filter specifications
In PCN the ingress and egress nodes should be able to identify the
ingress-egress-aggregate to which each flow belongs. Moreover, the
egress node also needs to associate an aggregate with the address of
the ingress node for receiving reports, if the ingress node is the
decision point. The filter specification at the PCN-egress-nodes
depends on the surrounding environment, e.g., pure IP, MPLS, GMPLS.
Karagiannis, et al. Expires January 5, 2011 [Page 6]
Internet-Draft PCN Signaling requirements July 2010
In this document, a possible IP filter spec for pure IP is given as an
example. In this case the filter spec should be able to identify a
flow using (all or a subset of the) following information:
o source IP address;
o destination IP address;
o protocol identifier and higher layer (port) addressing;
o flow label (typical for IPv6);
o SPI field for IPsec encapsulated data;
o DSCP/TOS field.
o IP address of PCN-ingress-node
o IP address of PCN-egress-node
3. Signaling Requirements between Decision Point and PCN-ingress-nodes
The decision point monitors and uses the PCN egress feedback sent by
the PCN-egress-node. There are situations that the decision point
must obtain an estimate of the rate at which PCN-traffic is being
admitted to the aggregate from the PCN-ingress-node.
In order to receive this information the decision point has to
request from the PCN-ingress-node to send the value of the PCN
traffic admitted to a certain aggregate.
Note that if the decision point and the PCN-ingress-node are
collocated, then the information exchanges between the decision point
and PCN-ingress-node are internal operations.
3.1 Signaled PCN ingress Feedback
The PCN-ingress-node measures per ingress-egress-aggregate the
following rate
o rate of admitted PCN traffic
This value is reported in octets/second to the decision point as
soon as possible after receiving the request from the decision
point. .
3.2 Signaled decision point trigger
The decision point uses the "ingress rate request" to request from
the PCN-ingress-node to send for a certain ingress-egress-aggregate,
the value of the admitted PCN traffic rate. The "ingress rate
request" message identifies the ingress-egress-aggregate for which
the admitted PCN traffic rate is required.
3.3 Signaling requirements
The same signaling requirements described in Section 2.3 apply for
this situation.
Karagiannis, et al. Expires January 5, 2011 [Page 7]
Internet-Draft PCN Signaling requirements July 2010
The only difference is the fact that these signaling
requirements apply for the signaling messages that have to be sent
between the decision point and PCN-ingress-nodes. Moreover, since the
"ingress rate request" message sent by the decision point towards
the PCN-ingress-node and the admitted PCN traffic rate sent by the
PCN-ingress-node towards the decision point are not sent regularly,
they SHOULD be delivered reliably.
4. Security Considerations
[RFC5559] provides a general description of the security
considerations for PCN. This memo introduces the additional security
considerations described in Section 2.3.7.
5. IANA Considerations
This memo includes no request to IANA.
6. Acknowledgements
We would like to acknowledge the members of the PCN working group for
the discussions that generated the contents of this memo.
7. References
7.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC5559] Eardley, P., "Pre-Congestion Notification (PCN)
Architecture", RFC 5559, June 2009.
[draft-ietf-pcn-cl-edge-behaviour-06] T. Taylor, A, Charny,
F. Huang, G. Karagiannis, M. Menth, "PCN Boundary Node
Behaviour for the Controlled Load (CL) Mode of Operation
(Work in progress)", June 2010.
[draft-ietf-pcn-sm-edge-behaviour-03] A. Charny, J. Zhang,
G. Karagiannis, M. Menth, T. Taylor, "PCN Boundary Node
Behaviour for the Single Marking (SM) Mode of Operation
(Work in progress)", June 2010.
7.2. Informative References
[RFC2205] Braden, B., Zhang, L., Berson, S., Herzog, S., and S.
Jamin, "Resource ReSerVation Protocol (RSVP) -- Version 1
Functional Specification", RFC 2205, September 1997.
Karagiannis, et al. Expires January 5, 2011 [Page 8]
Internet-Draft PCN Signaling requirements March 2010
[RFC3175] Baker, F., Iturralde, C. Le Faucher, F., Davie, B.,
"Aggregation of RSVP for IPv4 and IPv6 Reservations",
RFC 3175, 2001.
[RFC3209] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V.,
and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP
Tunnels", RFC 3209, December 2001.
[RFC3473] Berger, L., "Generalized Multi-Protocol Label Switching
(GMPLS) Signaling Resource ReserVation Protocol-Traffic
Engineering (RSVP-TE) Extensions", RFC 3473,
January 2003.
Authors' Addresses
Georgios Karagiannis
University of Twente
P.O. Box 217
7500 AE Enschede,
The Netherlands
EMail: g.karagiannis@ewi.utwente.nl
Tom Taylor
Huawei Technologies
1852 Lorraine Ave.
Ottawa, Ontario K1H 6Z8
Canada
Phone: +1 613 680 2675
Email: tom111.taylor@bell.net
Kwok Ho Chan
Huawei Technologies
125 Nagog Park
Acton, MA 01720
USA
Email: khchan@huawei.com
Michael Menth
University of Wurzburg
Institute of Computer Science
Room B206
Am Hubland, Wuerzburg D-97074
Germany
Email: menth@informatik.uni-wuerzburg.de
Karagiannis, et al. Expires January 5, 2011 [Page 9]
| PAFTECH AB 2003-2026 | 2026-04-23 06:11:11 |