One document matched: draft-ietf-pcn-marking-behaviour-03.txt
Differences from draft-ietf-pcn-marking-behaviour-02.txt
PCN Working Group Philip. Eardley (Editor)
Internet-Draft BT
Intended status: Standards Track May 8, 2009
Expires: November 9, 2009
Metering and marking behaviour of PCN-nodes
draft-ietf-pcn-marking-behaviour-03
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79. This document may contain material
from IETF Documents or IETF Contributions published or made publicly
available before November 10, 2008. The person(s) controlling the
copyright in some of this material may not have granted the IETF
Trust the right to allow modifications of such material outside the
IETF Standards Process. Without obtaining an adequate license from
the person(s) controlling the copyright in such materials, this
document may not be modified outside the IETF Standards Process, and
derivative works of it may not be created outside the IETF Standards
Process, except to format it for publication as an RFC or to
translate it into languages other than English.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on November 9, 2009.
Copyright Notice
Copyright (c) 2009 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Eardley (Editor) Expires November 9, 2009 [Page 1]
Internet-Draft PCN metering and marking May 2009
Provisions Relating to IETF Documents in effect on the date of
publication of this document (http://trustee.ietf.org/license-info).
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document.
Abstract
The objective of Pre-Congestion Notification (PCN) is to protect the
quality of service (QoS) of inelastic flows within a Diffserv domain,
in a simple, scalable and robust fashion. This document specifies
the two metering and marking behaviours of PCN-nodes. Threshold-
metering and -marking marks all PCN-packets if the PCN traffic rate
is greater than a configured rate ("PCN-threshold-rate"). Excess-
traffic-metering and -marking marks a proportion of PCN-packets, such
that the amount marked equals the traffic rate in excess of a
configured rate ("PCN-excess-rate"). The level of marking allows
PCN-boundary-nodes to make decisions about whether to admit or
terminate PCN-flows.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
Eardley (Editor) Expires November 9, 2009 [Page 2]
Internet-Draft PCN metering and marking May 2009
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 5
2. Specified PCN-metering and -marking behaviours . . . . . . . . 6
2.1. Behaviour aggregate classification function . . . . . . . 6
2.2. Dropping function . . . . . . . . . . . . . . . . . . . . 6
2.3. Threshold-meter function . . . . . . . . . . . . . . . . . 6
2.4. Excess-traffic-meter function . . . . . . . . . . . . . . 7
2.5. Marking function . . . . . . . . . . . . . . . . . . . . . 7
3. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 8
4. Security Considerations . . . . . . . . . . . . . . . . . . . 8
5. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 8
6. Changes (to be removed by RFC Editor) . . . . . . . . . . . . 9
6.1. Changes to -03 from -02 . . . . . . . . . . . . . . . . . 9
6.2. Changes to -02 from -01 . . . . . . . . . . . . . . . . . 9
6.3. Changes to -01 from -00 . . . . . . . . . . . . . . . . . 10
6.4. Changes to -00 . . . . . . . . . . . . . . . . . . . . . . 10
7. Informative References . . . . . . . . . . . . . . . . . . . . 11
Appendix A. Example algorithms . . . . . . . . . . . . . . . . . 12
A.1. Threshold-metering and -marking . . . . . . . . . . . . . 13
A.2. Excess-traffic-metering and -marking . . . . . . . . . . . 13
Appendix B. Implementation notes . . . . . . . . . . . . . . . . 14
B.1. Competing-non-PCN-traffic . . . . . . . . . . . . . . . . 14
B.2. Scope . . . . . . . . . . . . . . . . . . . . . . . . . . 16
B.3. Behaviour aggregate classification . . . . . . . . . . . . 16
B.4. Dropping . . . . . . . . . . . . . . . . . . . . . . . . . 17
B.5. Threshold-metering . . . . . . . . . . . . . . . . . . . . 18
B.6. Excess-traffic-metering . . . . . . . . . . . . . . . . . 19
B.7. Marking . . . . . . . . . . . . . . . . . . . . . . . . . 20
Author's Address . . . . . . . . . . . . . . . . . . . . . . . . . 21
Eardley (Editor) Expires November 9, 2009 [Page 3]
Internet-Draft PCN metering and marking May 2009
1. Introduction
The objective of Pre-Congestion Notification (PCN) is to protect the
quality of service (QoS) of inelastic flows within a Diffserv domain,
in a simple, scalable and robust fashion. Two mechanisms are used:
admission control, to decide whether to admit or block a new flow
request, and (in abnormal circumstances) flow termination to decide
whether to terminate some of the existing flows. To achieve this,
the overall rate of PCN traffic is metered on every link in the
domain, and PCN packets are appropriately marked when certain
configured rates are exceeded. These configured rates are below the
rate of the link thus providing notification to boundary nodes about
overloads before any congestion occurs (hence "pre-congestion
notification"). The level of marking allows boundary nodes to make
decisions about whether to admit or terminate.
This document standardises the two metering and marking behaviours of
PCN-nodes. Their aim is to enable PCN-nodes to give an "early
warning" of potential congestion before there is any significant
build-up of PCN-packets in their queues. In summary, their
objectives are:
o threshold-metering and -marking: its objective is to mark all PCN-
packets (with a "threshold-mark") whenever the rate of PCN-packets
is greater than its configured rate ("PCN-threshold-rate");
o excess traffic marking: whenever the rate of PCN-packets is
greater than its configured rate ("PCN-excess-rate"), its
objective is to mark PCN-packets (with an "excess-traffic-mark")
at a rate equal to the difference between the bit rate of PCN-
packets and the PCN-excess-rate.
[RFC3168] defines a broadly RED-like default congestion marking
behaviour, but allows alternatives to be defined; this document
defines such an alternative.
Section 2 below specifies the functions involved, which in outline
(see Figure 1) are:
o Behaviour aggregate (BA) classification: decide whether an
incoming packet is a PCN-packet or not.
o Dropping (optional): drop packets if the link is overloaded.
o Threshold-meter: determine whether the rate of PCN-packets is
greater than its configured PCN-threshold-rate. The meter
operates on all PCN-packets on the link, and not on individual
flows.
Eardley (Editor) Expires November 9, 2009 [Page 4]
Internet-Draft PCN metering and marking May 2009
o Excess-traffic-meter: measure by how much the rate of PCN-packets
is greater than its configured PCN-excess-rate. The meter
operates on all PCN-packets on the link, and not on individual
flows.
o PCN-mark: actually mark the PCN-packets, if the meter functions
indicate to do so.
+---------+ Result
+->|Threshold|-------+
| | Meter | |
| +---------+ V
+----------+ +- - - - -+ | +------+
| BA | | | | | | Marked
Packet =>|Classifier|==>| Dropper |==?===============>|Marker|==> Packet
Stream | | | | | | | Stream
+----------+ +- - - - -+ | +------+
| +---------+ ^
| | Excess | |
+->| Traffic |-------+
| Meter | Result
+---------+
Figure 1: Schematic of functions for PCN-metering and -marking
Appendix A gives an example of algorithms that fulfil the
specification of Section 2, and Appendix B provides some explanations
of and comments on Section 2. Both the Appendices are informative.
1.1. Terminology
In addition to the terminology defined in [I-D.ietf-pcn-architecture]
and [RFC2474], the following terms are defined:
o Competing-non-PCN-packet: a non PCN-packet that shares a link with
PCN-packets and competes with them for its forwarding bandwidth.
Competing-non-PCN-packets MUST NOT be PCN-marked (ie only PCN-
packets can be PCN-marked). Note: In general it is not advised to
have any competing-non-PCN-traffic.
o Metered-packet: a packet that is metered by the metering functions
specified in Sections 2.3 and 2.4. A PCN-packet MUST be treated
as a metered-packet (with the minor exception noted below in
Section 2.4). A competing-non-PCN-packet MAY be treated as a
metered-packet.
Eardley (Editor) Expires November 9, 2009 [Page 5]
Internet-Draft PCN metering and marking May 2009
2. Specified PCN-metering and -marking behaviours
This section specifies the two PCN-metering and -marking behaviours.
The descriptions are functional and are not intended to restrict the
implementation. The informative Appendices supplement this section.
2.1. Behaviour aggregate classification function
A PCN-node MUST classify a packet as a PCN-packet if the value of its
DSCP and ECN fields correspond to a PCN-enabled codepoint, as defined
in the encoding scheme applicable to the PCN-domain. Otherwise the
packet MUST NOT be classified as a PCN-packet.
A PCN-node MUST classify a packet as a competing-non-PCN-packet if it
is not a PCN-packet and it competes with PCN-packets for its
forwarding bandwidth on a link.
2.2. Dropping function
Note: if the PCN-node's queue overflows then naturally packets are
dropped. This section describes additional action.
On all links in the PCN-domain, dropping MAY be done by:
o metering all metered-packets to determine if the rate of metered-
traffic is greater than its scheduling rate (ie determine if any
packets are out-of-profile).
o if the rate of metered-traffic is too high, then drop metered-
packets.
If the PCN-node drops PCN-packets then:
o PCN-packets that arrive at the PCN-node already excess-traffic-
marked SHOULD be preferentially dropped;
o the PCN-node's excess-traffic-meter SHOULD NOT meter the PCN-
packets that it drops.
2.3. Threshold-meter function
A PCN-node MUST implement a threshold-meter that has behaviour
functionally equivalent to the following.
The meter acts like a token bucket, which is sized in bits and has a
configured bit rate, termed PCN-threshold-rate. The amount of tokens
in the token bucket is termed Ttm. Tokens are added at the PCN-
threshold-rate, to a maximum value BStm. Tokens are removed equal to
Eardley (Editor) Expires November 9, 2009 [Page 6]
Internet-Draft PCN metering and marking May 2009
the size in bits of the metered-packet, to a minimum Ttm=0.
(Explanation of abbreviations: T is short for Tokens, BS for bucket
size, and tm for threshold-meter.)
The token bucket has a configured intermediate depth, termed
threshold. If Ttm < threshold, then the meter indicates to the
marking function that the packet is to be threshold-marked; otherwise
it does not.
2.4. Excess-traffic-meter function
A PCN-packet SHOULD NOT be metered (by this excess-traffic-meter
function) in the following two cases:
o If the packet is already excess-traffic-marked on arrival at the
PCN-node;
o If this PCN-node drops the packet.
Otherwise the PCN-packet MUST be treated as a metered-packet, that is
it is metered by the excess-traffic-meter.
A PCN-node MUST implement an excess-traffic-meter that has behaviour
functionally equivalent to the following.
The meter acts like a token bucket, which is sized in bits and has a
configured bit rate, termed PCN-excess-rate. The amount of tokens in
the token bucket is termed Tetm. Tokens are added at the PCN-excess-
rate, to a maximum value BSetm. Tokens are removed equal to the size
in bits of the metered-packet, to a minimum Tetm=0. If the token
bucket is empty (Tetm = 0), then the meter indicates to the marking
function that the packet is to be excess-traffic-marked.
(Explanation of abbreviations: T is short for Tokens, BS for bucket
size, and etm for excess-traffic-meter.)
In addition to the above, if the token bucket is within an MTU of
being empty, then the meter SHOULD indicate to the marking function
that the packet is to be excess-traffic-marked; MTU means the maximum
size of PCN-packets on the link ("packet size independent marking").
Otherwise the meter MUST NOT indicate marking.
2.5. Marking function
A PCN-packet MUST be marked to reflect the metering results by
setting its encoding state appropriately, as specified by the
specific encoding scheme that applies in the PCN-domain. A
consistent choice of encoding scheme MUST be made throughout a PCN-
Eardley (Editor) Expires November 9, 2009 [Page 7]
Internet-Draft PCN metering and marking May 2009
domain.
A PCN-node MUST NOT:
o PCN-mark a packet that is not a PCN-packet;
o change a non PCN-packet into a PCN-packet;
o change a PCN-packet into a non PCN-packet.
3. IANA Considerations
This document makes no request of IANA.
Note to RFC Editor: this section may be removed on publication as an
RFC.
4. Security Considerations
Security considerations are discussed in detail in
[I-D.ietf-pcn-architecture].
5. Acknowledgements
This document is the result of extensive collaboration within the PCN
WG. Amongst the most active contributors to the development of the
ideas specified in this document have been Jozef Babiarz, Bob
Briscoe, Kwok-Ho Chan, Anna Charny, Philip Eardley, Georgios
Karagannis, Michael Menth, Toby Moncaster, Daisuke Satoh, and Joy
Zhang. Appendix A is based on text from Michael Menth.
This document is a development of [I-D.briscoe-tsvwg-cl-phb]. Its
authors are therefore contributors to this document: Bob Briscoe,
Philip Eardley, Dave Songhurst, Francois Le Faucheur, Anna Charny,
Vassilis Liatsos, Jozef Babiarz, Kwok-Ho Chan, Stephen Dudley,
Georgios Karagiannis, Attila Bader, Lars Westberg.
Thanks to those who've made comments on this draft: Michael Menth,
Joe Babiarz, Fred Baker, Bob Briscoe, Ken Carlberg, Anna Charny,
Ruediger Geib, Wei Gengyu, Fortune Huang, Christian Hublet, Ingemar
Johansson, Georgios Karagiannis, Toby Moncaster, Dimitri
Papadimitriou, Daisuke Satoh. Michael Menth, Joe Babiarz, Anna
Charny reviewed a preliminary version of the prior individual
internet draft.
Eardley (Editor) Expires November 9, 2009 [Page 8]
Internet-Draft PCN metering and marking May 2009
6. Changes (to be removed by RFC Editor)
6.1. Changes to -03 from -02
Updates to take account of last call comments as follows:
o renamed from "marking" to "metering and marking" (throughout) -
the former was intended as shorthand for the latter, but this was
found confusing
o added 'common capsule' summary of PCN to Introduction and removed
extraneous material
o replaced the term 'traffic conditioning' by 'dropping'
(throughout) - since the former has a wider meaning than just
dropping.
o discussion of the case with baseline encoding where there are two
PCN states - this is now done just once - in Section B.2.
o added in Section B.5 "The PCN-threshold-rate is configured at less
than the rate allocated to the PCN-traffic class" and in B.6 "The
PCN-excess-rate is configured at less than (or possibly equal to)
the rate allocated to the PCN-traffic class".
o configuring the PCN-excess-rate at greater than (or possibly equal
to) the PCN-threshold-rate - this is now in one place, as advice
is B5 & B6.
o SB.1: "voice-admit" corrected with references to I-D ietf-tsvwg-
admitted-realtime-dscp and RFC5127.
o "CL/SM edge behaviour" altered to the less obscure "controlled
load edge behaviour" and a reference added.
o S2.3, 2.4 & Appendix A: altered some of the abbreviations, for
better consistency with approach of RFC2698. eg TBthreshold.fill
=> Ttm.
o the ACKs section improved
o other minor corrections and clarifications
6.2. Changes to -02 from -01
Updates as follows:
Eardley (Editor) Expires November 9, 2009 [Page 9]
Internet-Draft PCN metering and marking May 2009
o added notes (end of S1.1 & 2.5) to clarify what "excess-traffic-
marked" means when there is only one encoding for PCN-marking
o added explanations for in Section B.4 and B.6 about why various
things are SHOULD or SHOULD NOT rather than MUST or MUST NOT.
o Deleted a couple of paragraphs about encoding states, as they are
relevant to encoding documents rather than this document.
6.3. Changes to -01 from -00
Updates as follows:
o corrected the term 'not PCN-marked' to 'not-marked' (throughout)
o re-phrased the definition of competing-non-PCN-packets
o corrected the definition of metered-packet
o delete most of Section 2.5 (marking function). The material
deleted belongs as part of [I-D.ietf-pcn-baseline-encoding]; other
encoding schemes would need to include similar material.
o deleted Appendix C (it was only a temporary archive of material
concerning per domain behaviour and PCN-boundary-node operation)
o clarifications throughout
o made all references Informative
6.4. Changes to -00
First version of WG draft, derived from
draft-eardley-pcn-marking-behaviour-01, with the following changes:
o Removed material concerning per domain behaviour and PCN-boundary-
node operation (temporarily archived to Appendix C)
o Removed mention of downgrading as an option for per-hop traffic
conditioning. In fact, downgrading is no longer allowed because S
2.6 now says "A PCN-node MUST NOT ...change a PCN-packet into a
non PCN-packet".
o Traffic conditioning is now a MAY. Since in general flow
termination (not traffic conditioning) is PCN's method for
handling problems of too much traffic.
Eardley (Editor) Expires November 9, 2009 [Page 10]
Internet-Draft PCN metering and marking May 2009
o Metered-packets: competing-non-PCN-packets now MAY be metered.
Since it is recommended that the operator doesn't allow any
competing-non-PCN-traffic, and (if there is) there are potentially
other ways of coping.
o No changes (outside traffic conditioning & metering of competing-
non-PCN-traffic) to the Normative sections of the draft.
o Appendix B.1 added about competing-non-PCN-traffic. Recommended
that there is no such traffic, but guidance given if there is.
7. Informative References
[I-D.briscoe-tsvwg-byte-pkt-mark]
Briscoe, B., "Byte and Packet Congestion Notification",
draft-briscoe-tsvwg-byte-pkt-mark-02 (work in progress),
February 2008.
[I-D.briscoe-tsvwg-cl-architecture]
Briscoe, B., "An edge-to-edge Deployment Model for Pre-
Congestion Notification: Admission Control over a
DiffServ Region", draft-briscoe-tsvwg-cl-architecture-04
(work in progress), October 2006.
[I-D.briscoe-tsvwg-cl-phb]
Briscoe, B., "Pre-Congestion Notification marking",
draft-briscoe-tsvwg-cl-phb-03 (work in progress),
October 2006.
[I-D.charny-pcn-comparison]
Charny, A., "Comparison of Proposed PCN Approaches",
draft-charny-pcn-comparison-00 (work in progress),
November 2007.
[I-D.ietf-pcn-architecture]
Eardley, P., "Pre-Congestion Notification (PCN)
Architecture", draft-ietf-pcn-architecture-11 (work in
progress), April 2009.
[I-D.ietf-pcn-baseline-encoding]
Moncaster, T., Briscoe, B., and M. Menth, "Baseline
Encoding and Transport of Pre-Congestion Information",
draft-ietf-pcn-baseline-encoding-03 (work in progress),
April 2009.
[I-D.ietf-tsvwg-admitted-realtime-dscp]
Baker, F., Polk, J., and M. Dolly, "DSCP for Capacity-
Eardley (Editor) Expires November 9, 2009 [Page 11]
Internet-Draft PCN metering and marking May 2009
Admitted Traffic",
draft-ietf-tsvwg-admitted-realtime-dscp-05 (work in
progress), November 2008.
[I-D.taylor-pcn-cl-edge-behaviour]
Charny, A., Huang, F., Menth, M., and T. Taylor, "PCN
Boundary Node Behaviour for the Controlled Load (CL) Mode
of Operation", draft-taylor-pcn-cl-edge-behaviour-00 (work
in progress), March 2009.
[Menth] "Menth", 2008, <http://www3.informatik.uni-wuerzburg.de/
staff/menth/Publications/Menth08-PCN-Overview.pdf>.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2474] Nichols, K., Blake, S., Baker, F., and D. Black,
"Definition of the Differentiated Services Field (DS
Field) in the IPv4 and IPv6 Headers", RFC 2474,
December 1998.
[RFC2475] Blake, S., Black, D., Carlson, M., Davies, E., Wang, Z.,
and W. Weiss, "An Architecture for Differentiated
Services", RFC 2475, December 1998.
[RFC3168] Ramakrishnan, K., Floyd, S., and D. Black, "The Addition
of Explicit Congestion Notification (ECN) to IP",
RFC 3168, September 2001.
[RFC5127] Chan, K., Babiarz, J., and F. Baker, "Aggregation of
DiffServ Service Classes", RFC 5127, February 2008.
Appendix A. Example algorithms
Note: This Appendix is informative, not normative. It is an example
of algorithms that implement Section 2 and is based on
[I-D.charny-pcn-comparison] and [Menth].
There is no attempt to optimise the algorithms. It implements the
metering and marking functions together. It is assumed that three
encoding states are available (one for threshold-marked, one for
excess-traffic-marked and one for not PCN-marked). It is assumed
that all metered-packets are PCN-packets and that the link is never
overloaded.
Eardley (Editor) Expires November 9, 2009 [Page 12]
Internet-Draft PCN metering and marking May 2009
A.1. Threshold-metering and -marking
A token bucket with the following parameters:
o PCN-threshold-rate: token rate of token bucket (bits/second)
o BStm: depth of token bucket (bits)
o threshold: marking threshold of token bucket (bits)
o lastUpdate: time the token bucket was last updated (seconds)
o Ttm: amount of tokens in token bucket (bits)
A PCN-packet has the following parameters:
o packet_size: the size of the PCN-packet (bits)
o packet_mark: the PCN encoding state of the packet
In addition there are the parameters:
o now: the current time (seconds)
The following steps are performed when a PCN-packet arrives on a
link:
o Ttm = min(BStm, Ttm + (now - lastUpdate) * PCN-threshold-rate); //
add tokens to token bucket
o Ttm = max(0, Ttm - packet_size); // remove tokens from token
bucket
o if ((Ttm < threshold) AND (packet_mark != excess-traffic-marked))
then packet_mark = threshold-marked; // do threshold marking, but
don't re-mark packets that are already excess-traffic-marked
o lastUpdate = now
A.2. Excess-traffic-metering and -marking
A token bucket with the following parameters:
o TBexcess.PCN-excess-rate: token rate of token bucket (bits/second)
o BSetm: depth of TB in token bucket (bits)
Eardley (Editor) Expires November 9, 2009 [Page 13]
Internet-Draft PCN metering and marking May 2009
o TBexcess.lastUpdate: time the token bucket was last updated
(seconds)
o Tetm: amount of tokens in token bucket (bits)
A PCN-packet has the following parameters:
o packet_size: the size of the PCN-packet (bits)
o packet_mark: the PCN encoding state of the packet
In addition there are the parameters:
o now: the current time (seconds)
o MTU: the maximum transfer unit of the link (or the known maximum
size of PCN-packets on the link) (bits)
The following steps are performed when a PCN-packet arrives on a
link:
o Tetm = min(BSetm, Tetm + (now - TBexcess.lastUpdate) *
TBexcess.PCN-excess-rate); // add tokens to token bucket
o if (packet_mark != excess-traffic-marked) then Tetm = max(0, Tetm
- packet_size); // remove tokens from token bucket, but do not
meter packets that are already excess-traffic-marked
o if (Tetm < MTU) then packet_mark = excess-traffic-marked; // do
(packet size independent) excess traffic marking
o lastUpdate = now
Appendix B. Implementation notes
Note: This Appendix is informative, not normative. It comments on
Section 2.
B.1. Competing-non-PCN-traffic
In general it is not advised to have any competing-non-PCN-traffic,
essentially because the unpredictable amount of competing-non-PCN-
traffic makes the PCN mechanisms less accurate and so reduces PCN's
ability to protect the QoS of admitted PCN-flows
[I-D.ietf-pcn-architecture]. But if there is competing-non-PCN-
traffic, then there needs to be:
Eardley (Editor) Expires November 9, 2009 [Page 14]
Internet-Draft PCN metering and marking May 2009
1. a mechanism to limit it, for example:
* limit the rate at which competing-non-PCN-traffic can be
forwarded on each link in the PCN-domain. One method for
achieving this is to queue competing-non-PCN-packets
separately from PCN-packets, and to limit the scheduling rate
of the former. Another method is to drop competing-non-PCN-
packets in excess of some rate.
* police competing-non-PCN-traffic at the PCN-ingress-nodes.
For example, as in the Diffserv architecture - although its
static traffic conditioning agreements risk a focused overload
of traffic from several PCN-ingress-nodes on one link.
* it is known by design that the level of competing-non-PCN-
traffic is always very small - perhaps it consists of operator
control messages only.
2. In general PCN's mechanisms should take account of competing-non-
PCN-traffic, in order to improve the accuracy of the decision
about whether to admit (or terminate) a PCN-flow. For example:
* competing-non-PCN-traffic contributes to the PCN meters (ie
competing-non-PCN-packets are treated as metered-packets).
* each PCN-node reduces, on its links, the PCN-threshold-rate
and PCN-excess-rate, in order to allow 'headroom' for the
competing-non-PCN-traffic; also limit the maximum forwarding
rate of competing-non-PCN-traffic to be less than the
'headroom'. In this case competing-non-PCN-packets are not
treated as metered-packets.
It is left up to the operator to decide on appropriate action.
Dropping is discussed further in Section B.4.
One specific example of competing-non-PCN-traffic occurs if the PCN-
compatible Diffserv codepoint is one of those that
[I-D.ietf-tsvwg-admitted-realtime-dscp]) defines as suitable for use
with admission control, and there is such non PCN-traffic in the PCN-
domain. A similar example could occur for Diffserv codepoints of the
Real-Time Treatment Aggregate [RFC5127]). In such cases PCN-traffic
and competing-non-PCN-traffic are distinguished by different values
of the ECN field [I-D.ietf-pcn-baseline-encoding].
Another example would occur if there is more than one PCN-compatible
Diffserv codepoint in a PCN-domain. For instance, suppose there are
two PCN-BAs treated at different priorities. Then as far as the
lower priority PCN-BA is concerned, the higher priority PCN-traffic
Eardley (Editor) Expires November 9, 2009 [Page 15]
Internet-Draft PCN metering and marking May 2009
needs to be treated as competing-non-PCN-traffic.
B.2. Scope
It may be known, eg by the design of the network topology, that some
links can never be pre-congested (even in unusual circumstances, eg
after the failure of some links). There is then no need to deploy
PCN behaviour on those links.
The meters can be implemented on the ingoing or outgoing interface of
a PCN-node. It may be that existing hardware can support only one
meter per ingoing interface and one per outgoing interface. Then for
instance threshold-metering could be run on all the ingoing
interfaces and excess-traffic-metering on all the outgoing
interfaces; note that the same choice must be made for all the links
in a PCN-domain to ensure that the two metering behaviours are
applied exactly once for all the links.
The baseline encoding [I-D.ietf-pcn-baseline-encoding] specifies only
two encoding states (PCN-marked and not-marked). In this case,
"excess-traffic-marked" means a packet that is PCN-marked as a result
of the excess-traffic-meter function, and "threshold-marked" means a
packet that is PCN-marked as a result of the threshold-meter
function. As far as terminology is concerned, this interpretation is
consistent with that defined in [I-D.ietf-pcn-architecture]. Note
that a deployment needs to make a consistent choice throughout the
PCN-domain whether PCN-marked is interpreted as excess-traffic-marked
or threshold-marked.
Note that even if there are only two encoding states, it is still
required that both the meters are implemented, in order to ease
compatibility between equipment, and to remove a configuration option
and associated complexity. Hardware with limited availability of
token buckets could be configured to run only one of the meters, but
it must be possible to enable either meter. Although in the scenario
with two encoding states indications from one of the meters are
ignored by the marking function, they may be logged or acted upon in
some other way, for example by the management system or an explicit
signalling protocol; such considerations are out of scope of this
document.
B.3. Behaviour aggregate classification
Configuration of PCN-nodes will define what values of the DSCP and
ECN fields indicate a PCN-packet in a particular PCN-domain.
Configuration will also define what values of the DSCP and ECN fields
indicate a competing-non-PCN-packet in a particular PCN-domain.
Eardley (Editor) Expires November 9, 2009 [Page 16]
Internet-Draft PCN metering and marking May 2009
B.4. Dropping
The objective of the dropping function is to minimise the queueing
delay suffered by metered-traffic at a PCN-node, since PCN-traffic
(and perhaps competing-non-PCN-traffic) is expected to be inelastic
traffic generated by real time applications. In practice it would be
defined as exceeding a specific traffic profile, typically based on a
token bucket.
If there is no competing-non-PCN-traffic, then it is not expected
that the dropping function is needed, since PCN's flow admission and
termination mechanisms limit the amount of PCN-traffic. Even so, it
still might be implemented as a back stop against misconfiguration of
the PCN-domain, for instance.
If there is competing-non-PCN-traffic, then the details of the
dropping function will depend on how the router's implementation
handles the two sorts of traffic (the discussion here is based on
that in [I-D.ietf-tsvwg-admitted-realtime-dscp]):
o a common queue for PCN-traffic and competing-non-PCN-traffic, and
a traffic conditioner for the competing-non-PCN-traffic; or
o separate queues. In this case the amount of competing-non-PCN-
traffic can be limited by limiting the rate at which the scheduler
(for the competing-non-PCN-traffic) forwards packets.
Note that only dropping of packets is allowed. Downgrading of
packets to a lower priority BA is not allowed (see B.7), since it
would lead to packet mis-ordering. Shaping ("the process of delaying
packets" [RFC2475]) is not suitable if the traffic comes from real
time applications.
In general it is reasonable for competing-non-PCN-traffic to get
harsher treatment than PCN-traffic (ie competing-non-PCN-packets are
preferentially dropped), because PCN's flow admission and termination
mechanisms are stronger than the mechanisms that are likely to be
applied to the competing-non-PCN-traffic. The PCN mechanisms also
mean that a dropper should not be needed for the PCN-traffic.
Preferential dropping of excess-traffic-marked packets: Section 2.3
specifies: "If the PCN-node drops PCN-packets then ... PCN-packets
that arrive at the PCN-node already excess-traffic-marked SHOULD be
preferentially dropped". In brief, the reason is that, with the
"controlled load" edge behaviour [I-D.taylor-pcn-cl-edge-behaviour]
this avoids over-termination in the event of multiple bottlenecks in
the PCN-domain [I-D.charny-pcn-comparison]. A fuller explanation is
as follows. The optimal dropping behaviour depends on the particular
Eardley (Editor) Expires November 9, 2009 [Page 17]
Internet-Draft PCN metering and marking May 2009
edge behaviour [Menth]. A single dropping behaviour is defined, as
it is simpler to standardise, implement and operate. The
standardised dropping behaviour is at least adequate for all edge
behaviours (and good for some), whereas others are not (for example
with tail dropping far too much traffic may be terminated with the
"controlled load" edge behaviour, in the event of multiple
bottlenecks in the PCN-domain [I-D.charny-pcn-comparison]). The
dropping behaviour is defined as a 'SHOULD', rather than a 'MUST', in
recognition that other dropping behaviour may be preferred in
particular circumstances, for example: (1) with the "marked flow"
termination edge behaviour, preferential dropping of unmarked packets
may be better [Menth]; (2) tail dropping may make PCN marking
behaviour easier to implement on current routers.
Exactly what "preferentially dropped" means is left to the
implementation. It is also left to the implementation what to do if
there are no excess-traffic-marked PCN-packets available at a
particular instant.
Section 2.2 also specifies: "the PCN-node's excess-traffic-meter
SHOULD NOT meter the PCN-packets that it drops." This avoids over-
termination [Menth]. Effectively it means that the dropping function
(if present) should be done before the meter functions - which is
natural.
B.5. Threshold-metering
The description is in terms of a 'token bucket with threshold' (which
[I-D.briscoe-tsvwg-cl-architecture] views as a virtual queue).
However the description is not intended to standardise
implementation.
The PCN-threshold-rate is configured at less than the rate allocated
to the PCN-traffic class. Also, the PCN-threshold-rate is less than,
or possibly equal to, the PCN-excess-rate.
Section 2.3 defines: "If Ttm < threshold, then the meter indicates to
the marking function that the packet is to be threshold-marked;
otherwise it does not." Note that a PCN-packet is marked without
explicit additional bias for the packet's size.
The behaviour must be functionally equivalent to the description in
Section 2.3. "Functionally equivalent" means the observable 'black
box' behaviour is the same or very similar, for example if either
precisely the same set of packets is marked, or if the set is shifted
by one packet. It is intended to allow implementation freedom over
matters such as:
Eardley (Editor) Expires November 9, 2009 [Page 18]
Internet-Draft PCN metering and marking May 2009
o whether tokens are added to the token bucket at regular time
intervals or only when a packet is processed.
o whether the new token bucket depth is calculated before or after
it is decided whether to mark the packet. The effect of this is
simply to shift the sequence of marks by one packet.
o when the token bucket is very nearly empty and a packet arrives
larger than Ttm, then the precise change in Ttm is up to the
implementation. For instance:
* set Ttm = 0 and indicate threshold-mark to the Marking
function.
* check whether Ttm < threshold and if it is then indicate
threshold-mark to the Marking function; then set Ttm = 0.
* leave Ttm unaltered and indicate threshold-mark to the Marking
function.
o similarly, when the token bucket is very nearly full and a packet
arrives larger than (BStm - Ttm), then the precise change in Ttm
is up to the implementation.
o Note that all packets, even if already marked, are metered by the
threshold-meter function (unlike the excess-traffic-meter
function), because all packets should contribute to the decision
whether there is room for a new flow.
B.6. Excess-traffic-metering
The description is in terms of a token bucket, however the
implementation is not standardised.
The PCN-excess-rate is configured at less than (or possibly equal to)
the rate allocated to the PCN-traffic class. Also, the PCN-excess-
rate is greater than, or possibly equal to, the PCN-threshold-rate.
As in Section B.3, "functionally equivalent" allows some
implementation flexibility when the token bucket is very nearly empty
or very nearly full.
Section 2.4 specifies: "A packet SHOULD NOT be metered (by this
excess traffic meter function) ... If the packet is already excess-
traffic-marked on arrival at the PCN-node". This avoids over-
termination (with some edge behaviours) in the event that the PCN-
traffic passes through multiple bottlenecks in the PCN-domain
[I-D.charny-pcn-comparison]. Note that an implementation could
Eardley (Editor) Expires November 9, 2009 [Page 19]
Internet-Draft PCN metering and marking May 2009
determine whether the packet is already excess-traffic-marked as an
integral part of its BA classification function. The behaviour is
defined as a 'SHOULD NOT', rather than a 'MUST NOT', because it may
be slightly harder to implement than a metering function that is
blind to previous packet markings.
Section 2.4 specifies: "A packet SHOULD NOT be metered (by this
excess traffic meter function) ... If this PCN-node drops the
packet." This avoids over-termination [Menth]. (A similar statement
could also be made for the threshold meter function, but is
irrelevant, as a link that is overloaded will already be
substantially pre-congested and hence threshold-marking all packets.)
It seems natural to perform the dropping function before the metering
functions, although for some equipment it may be harder to implement;
hence the behaviour is defined as a 'SHOULD NOT', rather than a 'MUST
NOT'.
Packet size independent marking is specified as a SHOULD in Section
2.4 ( "if the token bucket is within an MTU of being empty, then the
meter SHOULD indicate to the Marking function that the packet is to
be excess-traffic-marked; MTU means the maximum size of PCN-packets
on the link".) Without it, large packets are more likely to be
excess-traffic-marked than small packets and this means that, with
some edge behaviours, flows with large packets are more likely to be
terminated than flows with small packets
[I-D.briscoe-tsvwg-byte-pkt-mark] [Menth]. The behaviour is a
'SHOULD', rather than a 'MUST', because packet size independent
marking may be slightly harder for some equipment to implement, and
the impact of not doing it is undesirable but moderate (sufficient
traffic is terminated, but flows with large packets are more likely
to be terminated).
Note that BSetm is independent of BStm; Tetm is independent of Ttm
(except in that a packet changes both); and the two configured rates
(PCN-excess-rate and PCN-threshold-rate) are independent (except that
PCN-excess-rate >= PCN-threshold-rate).
B.7. Marking
Section 2.5 defines: "A PCN-node MUST NOT ...change a PCN-packet into
a non PCN-packet". This means that a PCN-node is not allowed to
downgrade a PCN-packet into a lower priority Diffserv BA (eg it is
not allowed as an alternative to dropping, Section 2.2).
Section 2.5 defines: "A PCN-node MUST NOT ...PCN-mark a packet that
is not a PCN-packet". This means that in the scenario where
competing-non-PCN-packets are treated as metered-packets, a meter may
indicate a packet is to be PCN-marked, but the marking function knows
Eardley (Editor) Expires November 9, 2009 [Page 20]
Internet-Draft PCN metering and marking May 2009
it cannot be marked. It is left open to the implementation exactly
what to do in this case; one simple possibility is to mark the next
PCN-packet. Note that unless the PCN-packets are a large fraction of
all the metered-packets then the PCN mechanisms may not work well.
Although the metering functions are described separately from the
marking function, they can be implemented in an integrated fashion.
Author's Address
Philip Eardley
BT
Adastral Park, Martlesham Heath
Ipswich IP5 3RE
UK
Email: philip.eardley@bt.com
Eardley (Editor) Expires November 9, 2009 [Page 21]
| PAFTECH AB 2003-2026 | 2026-04-23 03:59:12 |