One document matched: draft-ietf-p2psip-sip-00.txt
P2PSIP C. Jennings
Internet-Draft Cisco
Intended status: Standards Track B. Lowekamp, Ed.
Expires: April 30, 2009 SIPeerior Technologies
E. Rescorla
Network Resonance
S. Baset
H. Schulzrinne
Columbia University
October 27, 2008
A SIP Usage for RELOAD
draft-ietf-p2psip-sip-00
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on April 30, 2009.
Abstract
This document defines a SIP Usage for REsource LOcation And Discovery
(RELOAD), The SIP Usage provides the functionality of a SIP proxy or
registrar in a fully-distributed system. The SIP Usage provides
lookup service for AoRs stored in the overlay. The SIP Usage also
defines GRUUs that allow the registrations to map an AoR to a
specific node reachable through the overlay. The Attach method is
Jennings, et al. Expires April 30, 2009 [Page 1]
Internet-Draft RELOAD SIP Usage October 2008
used to establish a direct connection between nodes through which SIP
messages are exchanged.
Table of Contents
1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Registering AORs . . . . . . . . . . . . . . . . . . . . . . . 5
4. Looking up an AOR . . . . . . . . . . . . . . . . . . . . . . 7
5. Forming a Direct Connection . . . . . . . . . . . . . . . . . 8
6. GRUUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
7. SIP-REGISTRATION Kind Definition . . . . . . . . . . . . . . . 8
8. Security Considerations . . . . . . . . . . . . . . . . . . . 9
8.1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . 9
8.2. SIP-Specific Issues . . . . . . . . . . . . . . . . . . . 10
8.2.1. Fork Explosion . . . . . . . . . . . . . . . . . . . . 10
8.2.2. Malicious Retargeting . . . . . . . . . . . . . . . . 10
8.2.3. Privacy Issues . . . . . . . . . . . . . . . . . . . . 10
9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 10
10. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 10
11. References . . . . . . . . . . . . . . . . . . . . . . . . . . 11
11.1. Normative References . . . . . . . . . . . . . . . . . . . 11
11.2. Informative References . . . . . . . . . . . . . . . . . . 11
Appendix A. Change Log . . . . . . . . . . . . . . . . . . . . . 11
A.1. Changes since draft-ietf-p2psip-reload-00 . . . . . . . . 11
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 11
Intellectual Property and Copyright Statements . . . . . . . . . . 14
Jennings, et al. Expires April 30, 2009 [Page 2]
Internet-Draft RELOAD SIP Usage October 2008
1. Overview
The SIP Usage of RELOAD allows SIP user agents to provide a peer-to-
peer telephony service without the requirement for permanent proxy or
registration servers. In such a network, the RELOAD overlay itself
performs the registration and rendezvous functions ordinarily
associated with such servers.
The SIP Usage involves two basic functions:
Registration: SIP UAs can use the RELOAD data storage
functionality to store a mapping from their AOR to their Node-ID
in the overlay, and to retrieve the Node-ID of other UAs.
Rendezvous: Once a SIP UA has identified the Node-ID for an AOR it
wishes to call, it can use the RELOAD message routing system to
set up a direct connection which can be used to exchange SIP
messages.
For instance, Bob could register his Node-ID, "1234", under his AOR,
"sip:bob@dht.example.com". When Alice wants to call Bob, she queries
the overlay for "sip:bob@dht.example.com" and gets back Node-ID 1234.
She then uses the overlay to establish a direct connection with Bob
and can use that direct connection to perform a standard SIP INVITE.
The way this works is as follows:
1. Bob, operating Node-ID 1234, stores a mapping from his URI to his
Node-ID in the overlay. I.e., "sip:bob@dht.example.com -> 1234".
2. Alice, operating Node-ID 5678, decides to call Bob. She looks up
"sip:bob@dht.example.com" in the overlay and retrieves "1234".
3. Alice uses the overlay to route an Attach message to Bob's peer.
Bob responds with his own Attach and they set up a direct
connection, as shown below.
Jennings, et al. Expires April 30, 2009 [Page 3]
Internet-Draft RELOAD SIP Usage October 2008
Alice Peer1 Overlay PeerN Bob
(5678) (1234)
-------------------------------------------------
Attach ->
Attach ->
Attach ->
Attach ->
<- Attach
<- Attach
<- Attach
<- Attach
<------------------ ICE Checks ----------------->
INVITE ----------------------------------------->
<--------------------------------------------- OK
ACK -------------------------------------------->
<------------ ICE Checks for media ------------->
<-------------------- RTP ---------------------->
It is important to note that RELOAD's only role here is to set up the
direct connection between Alice and Bob. As soon as the ICE checks
complete and the connection is established, then ordinary SIP is
used. In particular, the establishment of the media channel for the
phone call happens via the usual SIP mechanisms, and RELOAD is not
involved. Media never goes over the overlay. After the successful
exchange of SIP messages, call peers run ICE connectivity checks for
media.
As well as allowing mappings from AORs to Node-IDs, the SIP Usage
also allows mappings from AORs to other AORs. For instance, if Bob
wanted his phone calls temporarily forwarded to Charlie, he could
store the mapping "sip:bob@dht.example.com ->
sip:charlie@dht.example.com". When Alice wants to call Bob, she
retrieves this mapping and can then fetch Charlie's AOR to retrieve
his Node-ID.
The SIP usage allows a RELOAD overlay to be used as a distributed SIP
registrar/proxy network augmenting the functionality of [RFC3263].
This entails three primary operations:
o Registering one's own AOR with the overlay.
o Looking up a given AOR in the overlay.
o Forming a direct connection to a given peer.
Jennings, et al. Expires April 30, 2009 [Page 4]
Internet-Draft RELOAD SIP Usage October 2008
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
We use the terminology and definitions from Concepts and Terminology
for Peer to Peer SIP [I-D.ietf-p2psip-concepts] and the RELOAD Base
Protocol [I-D.ietf-p2psip-base] extensively in this document.
3. Registering AORs
In ordinary SIP, a UA registers its AOR and location with a
registrar. In RELOAD, this registrar function is provided by the
overlay as a whole. To register its location, a RELOAD peer stores a
SipRegistration structure under its own AOR. This uses the SIP-
REGISTRATION Kind-ID, which is formally defined in Section 7.
Note: GRUUs are handled via a separate mechanism, as described in
Section 6.
As a simple example, if Alice's AOR were "sip:alice@dht.example.com"
and her Node-ID were "1234", she might store the mapping
"sip:alice@example.org -> 1234". This would tell anyone who wanted
to call Alice to contact node "1234".
RELOAD peers MAY store two kinds of SIP mappings:
o From AORs to destination lists (a single Node-ID is just a trivial
destination list.)
o From AORs to other AORs.
The meaning of the first kind of mapping is "in order to contact me,
form a connection with this peer." The meaning of the second kind of
mapping is "in order to contact me, dereference this AOR". This
allows for forwarding. For instance, if Alice wants calls to her to
be forwarded to her secretary, Sam, she might insert the following
mapping "sip:alice@dht.example.org -> sip:sam@dht.example.org".
The contents of a SipRegistration structure are as follows:
Jennings, et al. Expires April 30, 2009 [Page 5]
Internet-Draft RELOAD SIP Usage October 2008
enum {sip_registration_uri (1), sip_registration_route (2),
(255)} SipRegistrationType;
select (SipRegistration.type) {
case sip_registration_uri:
opaque uri<0..2^16-1>;
case sip_registration_route:
opaque contact_prefs<0..2^16-1>;
Destination destination_list<0..2^16-1>;
/* This type can be extended */
} SipRegistrationData;
struct {
SipRegistrationType type;
uint16 length;
SipRegistrationData data;
} SipRegistration;
The contents of the SipRegistration PDU are:
type
the type of the registration
length
the length of the rest of the PDU
data
the registration data
o If the registration is of type "sip_registration_uri", then the
contents are an opaque string containing the URI.
o If the registration is of type "sip_registration_route", then the
contents are an opaque string containing the callee's contact
preferences and a destination list for the peer.
RELOAD explicitly supports multiple registrations for a single AOR.
The registrations are stored in a Dictionary with the dictionary keys
being Node-IDs. Consider, for instance, the case where Alice has two
peers:
Jennings, et al. Expires April 30, 2009 [Page 6]
Internet-Draft RELOAD SIP Usage October 2008
o her desk phone (1234)
o her cell phone (5678)
Alice might store the following in the overlay at resource
"sip:alice@dht.example.com".
o A SipRegistration of type "sip_registration_route" with dictionary
key "1234" and value "1234".
o A SipRegistration of type "sip_registration_route" with dictionary
key "5678" and value "5678".
Note that this structure explicitly allows one Node-ID to forward to
another Node-ID. For instance, Alice could set calls to her desk
phone to ring at her cell phone. It's not clear that this is useful
in this case, but may be useful if Alice has two AORs.
In order to prevent hijacking, registrations are subject to access
control rules. Before a Store is permitted, the storing peer MUST
check that:
o The certificate contains a username that is a SIP AOR that hashes
to the Resource-ID being stored at.
o The certificate contains a Node-ID that is the same as the
dictionary key being stored at.
Note that these rules permit Alice to forward calls to Bob without
his permission. However, they do not permit Alice to forward Bob's
calls to her. See Section 8.2.2 for more on this point.
4. Looking up an AOR
When a RELOAD user wishes to call another user, starting with a non-
GRUU AOR, he follows the following procedure. (GRUUs are discussed
in Section 6).
1. Check to see if the domain part of the AOR matches the domain
name of an overlay of which he is a member. If not, then this is
an external AOR, and he MUST do one of the following:
* Fail the call.
* Use ordinary SIP procedures.
* Attempt to become a member of the overlay indicated by the
domain part, if that overlay is a RELOAD overlay.)
2. Perform a Fetch for kind SIP-REGISTRATION at the Resource-ID
corresponding to the AOR. This Fetch SHOULD NOT indicate any
dictionary keys, which will result in fetching all the stored
values.
Jennings, et al. Expires April 30, 2009 [Page 7]
Internet-Draft RELOAD SIP Usage October 2008
3. If any of the results of the Fetch are non-GRUU AORs, then repeat
step 1 for that AOR.
4. Once only GRUUs and destination lists remain, the peer removes
duplicate destination lists and GRUUs from the list and forms a
SIP connection to the appropriate peers as described in the
following sections. If there are also external AORs, the peer
follows the appropriate procedure for contacting them as well.
5. Forming a Direct Connection
Once the peer has translated the AOR into a set of destination lists,
it then uses the overlay to route Attach messages to each of those
peers. The "application" field MUST be 5060 to indicate SIP. If
certificate-based authentication is in use, the responding peer MUST
present a certificate with a Node-ID matching the terminal entry in
the route list. Note that it is possible that the peers already have
a RELOAD connection between them. This MUST NOT be used for SIP
messages. However, if a SIP connection already exists, that MAY be
used. Once the Attach succeeds, the peer sends SIP messages over the
connection as in normal SIP.
6. GRUUs
GRUUs do not require storing data in the Overlay Instance. Rather,
they are constructed by embedding a base64-encoded destination list
in the gr URI parameter of the GRUU. The base64 encoding is done
with the alphabet specified in table 1 of RFC 4648 with the exception
that ~ is used in place of =. An example GRUU is
"sip:alice@example.com;gr=MDEyMzQ1Njc4OTAxMjM0NTY3ODk~". When a peer
needs to route a message to a GRUU in the same P2P network, it simply
uses the destination list and connects to that peer.
Because a GRUU contains a destination list, it MAY have the same
contents as a destination list stored elsewhere in the resource
dictionary.
Anonymous GRUUs are done in roughly the same way but require either
that the enrollment server issue a different Node-ID for each
anonymous GRUU required or that a destination list be used that
includes a peer that compresses the destination list to stop the
Node-ID from being revealed.
7. SIP-REGISTRATION Kind Definition
The first mapping is provided using the SIP-REGISTRATION Kind-ID:
Jennings, et al. Expires April 30, 2009 [Page 8]
Internet-Draft RELOAD SIP Usage October 2008
Kind IDs The Resource Name for the SIP-REGISTRATION Kind-ID is the
AOR of the user. The data stored is a SipRegistrationData, which
can contain either another URI or a destination list to the peer
which is acting for the user.
Data Model The data model for the SIP-REGISTRATION Kind-ID is
dictionary. The dictionary key is the Node-ID of the storing
peer. This allows each peer (presumably corresponding to a single
device) to store a single route mapping.
Access Control If certificate-based access control is being used,
stored data of Kind-ID SIP-REGISTRATION must be signed by a
certificate which (1) contains user name matching the storing URI
used as the Resource Name for the Resource-ID and (2) contains a
Node-ID matching the storing dictionary key.
Data stored under the SIP-REGISTRATION kind is of type
SipRegistration. This comes in two varieties:
sip_registration_uri
a URI which the user can be reached at.
sip_registration_route
a destination list which can be used to reach the user's peer.
8. Security Considerations
8.1. Overview
RELOAD provides a generic storage service, albeit one designed to be
useful for P2PSIP. In this section we discuss security issues that
are likely to be relevant to any usage of RELOAD. In Section 8.2 we
describe issues that are specific to SIP.
In any Overlay Instance, any given user depends on a number of peers
with which they have no well-defined relationship except that they
are fellow members of the Overlay Instance. In practice, these other
nodes may be friendly, lazy, curious, or outright malicious. No
security system can provide complete protection in an environment
where most nodes are malicious. The goal of security in RELOAD is to
provide strong security guarantees of some properties even in the
face of a large number of malicious nodes and to allow the overlay to
function correctly in the face of a modest number of malicious nodes.
P2PSIP deployments require the ability to authenticate both peers and
resources (users) without the active presence of a trusted entity in
Jennings, et al. Expires April 30, 2009 [Page 9]
Internet-Draft RELOAD SIP Usage October 2008
the system. We describe two mechanisms. The first mechanism is
based on public key certificates and is suitable for general
deployments. The second is an admission control mechanism based on
an overlay-wide shared symmetric key.
8.2. SIP-Specific Issues
8.2.1. Fork Explosion
Because SIP includes a forking capability (the ability to retarget to
multiple recipients), fork bombs are a potential DoS concern.
However, in the SIP usage of RELOAD, fork bombs are a much lower
concern because the calling party is involved in each retargeting
event and can therefore directly measure the number of forks and
throttle at some reasonable number.
8.2.2. Malicious Retargeting
Another potential DoS attack is for the owner of an attractive number
to retarget all calls to some victim. This attack is difficult to
ameliorate without requiring the target of a SIP registration to
authorize all stores. The overhead of that requirement would be
excessive and in addition there are good use cases for retargeting to
a peer without there explicit cooperation.
8.2.3. Privacy Issues
All RELOAD SIP registration data is public. Methods of providing
location and identity privacy are still being studied.
9. IANA Considerations
This section contains the new code points registered by this
document.
TODO define SIP usage specific kinds, etc here.
10. Acknowledgments
This draft is a merge of the "REsource LOcation And Discovery
(RELOAD)" draft by David A. Bryan, Marcia Zangrilli and Bruce B.
Lowekamp, the "Address Settlement by Peer to Peer" draft by Cullen
Jennings, Jonathan Rosenberg, and Eric Rescorla, the "Security
Extensions for RELOAD" draft by Bruce B. Lowekamp and James Deverick,
the "A Chord-based DHT for Resource Lookup in P2PSIP" by Marcia
Zangrilli and David A. Bryan, and the Peer-to-Peer Protocol (P2PP)
Jennings, et al. Expires April 30, 2009 [Page 10]
Internet-Draft RELOAD SIP Usage October 2008
draft by Salman A. Baset, Henning Schulzrinne, and Marcin
Matuszewski.
Thanks to the many people who contributed including: Michael Chen,
TODO - fill in.
11. References
11.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3263] Rosenberg, J. and H. Schulzrinne, "Session Initiation
Protocol (SIP): Locating SIP Servers", RFC 3263,
June 2002.
[I-D.ietf-p2psip-base]
Jennings, C., Lowekamp, B., Rescorla, E., Baset, S., and
H. Schulzrinne, "REsource LOcation And Discovery (RELOAD)
Base Protocol", draft-ietf-p2psip-base-00 (work in
progress), October 2008.
11.2. Informative References
[I-D.ietf-p2psip-concepts]
Bryan, D., Matthews, P., Shim, E., Willis, D., and S.
Dawkins, "Concepts and Terminology for Peer to Peer SIP",
draft-ietf-p2psip-concepts-02 (work in progress),
July 2008.
Appendix A. Change Log
A.1. Changes since draft-ietf-p2psip-reload-00
o Split SIP Usage from combined draft into new draft.
Jennings, et al. Expires April 30, 2009 [Page 11]
Internet-Draft RELOAD SIP Usage October 2008
Authors' Addresses
Cullen Jennings
Cisco
170 West Tasman Drive
MS: SJC-21/2
San Jose, CA 95134
USA
Phone: +1 408 421-9990
Email: fluffy@cisco.com
Bruce B. Lowekamp (editor)
SIPeerior Technologies
5251-18 John Tyler Highway #330
Williamsburg, VA 23185
USA
Email: bbl@lowekamp.net
Eric Rescorla
Network Resonance
2064 Edgewood Drive
Palo Alto, CA 94303
USA
Phone: +1 650 320-8549
Email: ekr@networkresonance.com
Salman A. Baset
Columbia University
1214 Amsterdam Avenue
New York, NY
USA
Email: salman@cs.columbia.edu
Jennings, et al. Expires April 30, 2009 [Page 12]
Internet-Draft RELOAD SIP Usage October 2008
Henning Schulzrinne
Columbia University
1214 Amsterdam Avenue
New York, NY
USA
Email: hgs@cs.columbia.edu
Jennings, et al. Expires April 30, 2009 [Page 13]
Internet-Draft RELOAD SIP Usage October 2008
Full Copyright Statement
Copyright (C) The IETF Trust (2008).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Jennings, et al. Expires April 30, 2009 [Page 14]
| PAFTECH AB 2003-2026 | 2026-04-23 22:39:01 |