One document matched: draft-ietf-mmusic-sctp-sdp-12.xml
<?xml version="1.0"?>
<?rfc symrefs="yes"?>
<!DOCTYPE rfc SYSTEM "rfc2629.dtd">
<?rfc toc="yes" ?>
<?rfc compact="yes" ?>
<?rfc subcompact="no" ?>
<?rfc sortrefs="no" ?>
<rfc category="std" docName="draft-ietf-mmusic-sctp-sdp-12" ipr="trust200902">
<?xml-stylesheet type="text/xsl" href="rfc2629.xslt" ?>
<front>
<title abbrev="The SCTP protocol identifier for SDP">
Stream Control Transmission Protocol (SCTP)-Based Media
Transport in the Session Description Protocol (SDP)
</title>
<author initials="C." surname="Holmberg" fullname="Christer Holmberg">
<organization>Ericsson</organization>
<address>
<postal>
<street>Hirsalantie 11</street>
<code>02420</code>
<city>Jorvas</city>
<country>Finland</country>
</postal>
<email>christer.holmberg@ericsson.com</email>
</address>
</author>
<author initials="S." surname="Loreto" fullname="Salvatore Loreto">
<organization>Ericsson</organization>
<address>
<postal>
<street>Hirsalantie 11</street>
<code>02420</code>
<city>Jorvas</city>
<country>Finland</country>
</postal>
<email>Salvatore.Loreto@ericsson.com</email>
</address>
</author>
<author initials="G." surname="Camarillo" fullname="Gonzalo Camarillo">
<organization>Ericsson</organization>
<address>
<postal>
<street>Hirsalantie 11</street>
<code>02420</code>
<city>Jorvas</city>
<country>Finland</country>
</postal>
<email>Gonzalo.Camarillo@ericsson.com</email>
</address>
</author>
<date year="2015"/>
<area>RAI</area>
<workgroup>MMUSIC</workgroup>
<keyword>SCTP, SDP, DTLS</keyword>
<abstract>
<t>
SCTP (Stream Control Transmission Protocol) is a transport protocol used to
establish associations between two endpoints.
</t>
<t>
This specification describes how
to describe SCTP associations using the Session Description Protocol (SDP),
and defines the following new SDP Media Description protocol identifiers
(proto values):'SCTP', 'SCTP/DTLS', 'UDP/DTLS/SCTP' and 'TCP/DTLS/SCTP'.
</t>
<t>
The specification also describes how to use the new proto values together
with the SDP Offer/Answer mechanism in order to negotiate and establish
SCTP associations, and how to indicate the SCTP application usage.
</t>
</abstract>
</front>
<middle>
<section title="Introduction">
<t>
SDP (Session Description Protocol) <xref target="RFC4566"/> provides a
general-purpose format for describing multimedia sessions in announcements
or invitations. TCP-Based Media Transport in the Session Description Protocol
(SDP) <xref target="RFC4145"/> specifies a general mechanism for describing and
establishing TCP (Transmission Control Protocol) <xref target="RFC5246"/> streams.
Connection-Oriented Media Transport over the Transport Layer Security (TLS)
Protocol in the Session Description Protocol (SDP) <xref target="RFC4572"/>
extends RFC4145 <xref target="RFC4145"/> for describing TCP-based media
streams that are protected using TLS.
</t>
<t>
SCTP (Stream Control Transmission Protocol) is a transport protocol used to
establish associations between two endpoints.
</t>
<t>
This specification describes how
to describe SCTP associations using the Session Description Protocol (SDP)
<xref target="RFC4566"/>, and defines the following new SDP Media Description
<xref target="RFC4566"/> protocol identifiers (proto values):'SCTP', 'SCTP/DTLS',
'UDP/DTLS/SCTP' and 'TCP/DTLS/SCTP'.
</t>
<t>
The specification also describes how to use the new proto values together
with the SDP Offer/Answer mechanism <xref target="RFC3264"/> in order to
negotiate and establish SCTP associations, and how to indicate the SCTP
application usage.
</t>
<t>
NOTE: TLS is designed to run on top of a byte-stream oriented transport
protocol providing a reliable, in-sequence delivery like TCP.
<xref target="RFC6083"/> presents serious limitations with
transporting SCTP on top of TLS. Therefore, defining a mechanism
to negotiate media streams transported using SCTP on top of TLS
is outside the scope of this specification.
</t>
</section>
<section title="Terminology">
<t>
In this document, the key words "MUST", "MUST NOT", "REQUIRED",
"SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT
RECOMMENDED", "MAY", and "OPTIONAL" are to be interpreted as described
in BCP 14, <xref target="RFC2119">RFC 2119</xref> and indicate
requirement levels for compliant implementations.
</t>
</section>
<section title="SCTP Terminology">
<t>
SCTP Association: A protocol relationship between SCTP endpoints,
composed of the two SCTP endpoints and protocol state information
including Verification Tags and the currently active set of
Transmission Sequence Numbers (TSNs), etc. An association can be
uniquely identified by the transport addresses used by the
endpoints in the association. Two SCTP endpoints MUST NOT have
more than one SCTP association between them at any given time.
</t>
<t>
SCTP Stream: A unidirectional logical channel established from one to
another associated SCTP endpoint, within which all user messages
are delivered in sequence except for those submitted to the
unordered delivery service.
</t>
<t>
SCTP Transport address: A transport address is traditionally defined by
a network-layer address, a transport-layer protocol, and a
transport-layer port number. In the case of SCTP running over IP,
a transport address is defined by the combination of an IP address
and an SCTP port number (where SCTP is the transport protocol).
</t>
</section>
<section title="SDP Media Descriptions" anchor="m-line">
<section title="General" anchor="m-line-gen">
<t>
This section defines the following new SDP Media Description (m- line)
protocol identifiers (proto values) for describing an SCTP association:
'SCTP', 'SCTP/DTLS', 'UDP/DTLS/SCTP' and 'TCP/DTLS/SCTP'. The section
also describes how an m- line, associated with the proto values, is created.
</t>
<t>
The following is the format for an 'm' line, as specified in RFC4566
<xref target="RFC4566"/>:
</t>
<figure>
<artwork><![CDATA[
m=<media> <port> <proto> <fmt> ...
]]></artwork>
</figure>
<t>
The 'SCTP', 'SCTP/DTLS', 'UDP/DTLS/SCTP' and 'TCP/DTLS/SCTP' proto
values are similar to both the 'UDP' and 'TCP' proto values in that they
only describe the transport-layer protocol and not the upper-layer
protocol.
</t>
<t>
NOTE: When the 'UDP/DTLS/SCTP' and 'TCP/DTLS/SCTP' proto values are used,
the underlying transport protocol is either UDP or TCP, SCTP is carried
on top of either of those transport-layer protocols.
</t>
<t>
The m- line fmt value, identifying the application-layer protocol,
MUST be registered by IANA.
</t>
</section>
<section title="Protocol Identifiers" anchor="proto">
<t>
The new proto values are defined as below:
</t>
<t>
<list style="symbols">
<t>
The 'SCTP' proto value describes an SCTP association, as
defined in <xref target="RFC4960"/>.
</t>
<t>
The 'SCTP/DTLS' proto value describes a Datagram Transport Layer
Security (DTLS) <xref target="RFC6347"/>
connection on top of an SCTP association, as defined in <xref target="RFC6083"/>.
</t>
<t>
The 'UDP/DTLS/SCTP' proto value describes an SCTP association on top of
a DTLS connection on top of UDP, as defined in
<xref target="sec-udp-dtls-sctp"/>.
</t>
<t>
The 'TCP/DTLS/SCTP' proto value describes an SCTP association on top of
a DTLS connection on top of TCP, as defined in
<xref target="sec-tcp-dtls-sctp"/>.
</t>
</list>
</t>
</section>
<section title="Media Format Management" anchor="media">
<t>
<xref target="RFC4566"/> defines that specifications defining new proto values must
define the rules by which their media format (fmt) namespace is managed.
Use of an existing MIME subtype for the format is encouraged. If no MIME subtype
exists, it is recommended that a suitable one is registered through the
IETF process <xref target="RFC6838"/> <xref target="RFC4289"/> by production of, or
reference to, a standards-track RFC that defines the transport protocol for the format.
</t>
<t>
An m- line with a proto value of 'SCTP', 'SCTP/DTLS', 'UDP/DTLS/SCTP' or 'TCP/DTLS/SCTP'
always describe a single SCTP association.
</t>
<t>
In addition, such m- line MUST further indicate the application-layer protocol
using an 'fmt' identifier. There MUST be exactly one 'fmt' value per m- line associated
with the proto values defined in this specification. The "fmt" namespace associated
with those proto values describes the generic application usage of the entire SCTP
association, including the associated SCTP streams.
</t>
<t>
NOTE: A mechanism on how to describe, and manage, individual SCTP streams within an
SCTP association, is outside the scope of this specification.
</t>
</section>
<section title="Syntax" anchor="m-line-syn">
<figure>
<artwork><![CDATA[
sctp-m-line = %x6d "="
("application" SP sctp-port SP "SCTP" SP fmt CRLF) /
("application" SP sctp-port SP "SCTP/DTLS" SP fmt CRLF) /
("application" SP udp-port SP "UDP/DTLS/SCTP" SP fmt CRLF) /
("application" SP tcp-port SP "TCP/DTLS/SCTP" SP fmt CRLF)
sctp-port = port
udp-port = port
tcp-port = port
fmt = association-usage
association-usage = token
]]></artwork>
</figure>
</section>
<section title="Example">
<figure>
<artwork><![CDATA[
m=application 12345 UDP/DTLS/SCTP webrtc-datachannel
a=max-message-size: 100000
]]></artwork>
</figure>
</section>
</section>
<section title="SDP 'sctp-port' Attribute" anchor="attr-sctp-port">
<section title="General" anchor="attr-sctp-port-gen">
<t>
This section defines a new SDP media-level attribute, 'sctp-port'.
The attribute can be associated with an SDP media descriptor (m- line)
with a 'UDP/DTLS/SCTP' or a 'TCP/DTLS/SCTP' proto value, in which case
the m- line port value indicates the port of the transport-layer
protocol (UDP or TCP), on which SCTP is carried.
</t>
<t>
If the SDP sctp-port attribute is not present, the m- line MUST
be discarded.
</t>
<t>
Usage of the SDP sctp-port attribute with other proto values
is not specified, and MUST be discarded if received.
</t>
</section>
<section title="Syntax" anchor="attr-sctp-port-syn">
<figure>
<artwork><![CDATA[
sctp-port-attr = "a=sctp-port:" port
port = 1*DIGIT
]]></artwork>
</figure>
</section>
</section>
<section title="SDP 'max-message-size' Attribute" anchor="attr-max-message-size">
<section title="General" anchor="attr-max-message-size-gen">
<t>
The SDP 'max-message-size' attribute can be associated with an m- line to
indicate the maximum message size that an SCTP endpoint is willing to receive
on the SCTP association associated with the m- line.
</t>
<t>
The remote peer MUST assume that larger messages will be rejected by the
SCTP endpoint. SCTP endpoints need to decide on appropriate behavior in
case a message that exceeds the maximum size needs to be sent.
</t>
<t>
If the SDP 'max-message-size' attribute contains a maximum message size
value of zero, it indicates the SCTP endpoint will handle messages of any size,
subject to memory capacity etc.
</t>
<t>
If the SDP 'max-message-size' attribute is not present, the default value is
64K.
</t>
<t>
NOTE: This specification only defines the usage of the SDP 'max-message-size'
attribute when associated with an m- line containing one of the following proto
values: 'SCTP', 'SCTP/DTLS', 'UDP/DTLS/SCTP' or 'TCP/DTLS/SCTP'.
Usage of the attribute with other proto values needs to be defined
in a separate specification.
</t>
</section>
<section title="Syntax" anchor="attr-max-message-size-syn">
<figure>
<artwork><![CDATA[
max-message-size-attr = "a=max-message-size:" max-message-size
max-message-size = 1*DIGIT
]]></artwork>
</figure>
</section>
</section>
<section title="SDP 'fmtp' Attribute" anchor="attr-fmtp">
<t>
The SDP 'fmtp' attribute <xref target="RFC4566"/> can be used
to carry association-usage specific parameters. If the
attribute is used with a specific association-usage, the
usage and detailed syntax MUST be defined in that
association-usage specification.
</t>
</section>
<section title="UDP/DTLS/SCTP Transport Realization" anchor="sec-udp-dtls-sctp">
<t>
The UDP/DTLS/SCTP transport is realized as described below:
</t>
<t>
<list style="symbols">
<t>
SCTP on top of DTLS is realized according to the procedures
defined in <xref target="I-D.ietf-tsvwg-sctp-dtls-encaps"/>; and
</t>
<t>
DTLS on top of UDP is realized according to the procedures in
defined in <xref target="RFC6347"/>.
</t>
</list>
</t>
</section>
<section title="TCP/DTLS/SCTP Transport Realization" anchor="sec-tcp-dtls-sctp">
<t>
The TCP/DTLS/SCTP transport is realized as described below:
</t>
<t>
<list style="symbols">
<t>
SCTP on top of DTLS is realized according to the procedures
defined in <xref target="I-D.ietf-tsvwg-sctp-dtls-encaps"/>; and
</t>
<t>
DTLS on top of TCP is realized using the framing method defined in
<xref target="RFC4571"/>.
</t>
</list>
</t>
<t>
NOTE: DTLS on top of TCP, without using the framing method defined in
<xref target="RFC4571"/> is outside the scope of this specification.
A separate proto value would need to be registered for such
transport realization.
</t>
</section>
<section title="SCTP Association Management" anchor="sec-attributes-mgmt">
<section title="General" anchor="sec-attributes-mgmt-gen">
<t>
The management of an SCTP association is identical to the management
of a TCP connection. An SCTP endpoints MUST follow the rules in
Section 6 of <xref target="RFC4145"/> to manage SCTP associations.
Whether to use the SCTP ordered or unordered delivery service is up
to the applications using the SCTP association, and this specification
does not define a mechanism to indicate the type of delivery service
using SDP.
</t>
</section>
<section title="SDP sendrecv/sendonly/sendrecv/inactive Attribute" anchor="sec-attributes-direction">
<t>
This specification does not define semantics for the SDP direction
attributes <xref target="RFC4566"/>. Specifications for an individual
SCTP association usage MAY define how the attributes can be used with
that usage. Unless semantics of these attributes for an SCTP association
usage have been defined, SDP direction attributes MUST be discarded if present.
</t>
</section>
<section title="SDP setup Attribute" anchor="sec-attributes-setup">
<section title="General" anchor="sec-attributes-setup-gen">
<t>
The SDP setup attribute is used to determine the 'active/passive'
status of the endpoints, following the procedures for TCP in
<xref target="RFC4145"/>.
</t>
</section>
<section title="SCTP Association Initiation" anchor="sec-attributes-setup-init">
<t>
Both the 'active' and 'passive' endpoint MUST initiate the SCTP association,
and MUST use the same SCTP port as client port and server port
(in order to prevent two separate SCTP associations from being established).
</t>
<t>
NOTE: The procedure above is different from TCP, where only the 'active'
endpoint initiates the TCP connection <xref target="RFC4145"/>.
</t>
<t>
If the m- line proto value is 'TCP/DTLS/SCTP', only the 'active' endpoint
will initiate the TCP connection, following the procedures in
<xref target="RFC4145"/>. Both endpoints will still initiate the SCTP association
on top of the TCP connection.
</t>
</section>
<section title="TLS Role Determination" anchor="sec-attributes-setup-tls">
<t>
If the m- line proto value is 'SCTP/DTLS', 'UDP/DTLS/SCTP'
or 'TCP/DTLS/SCTP', the 'active/passive' status is used to determine
the TLS roles of the endpoints. Following the procedures in
<xref target="RFC4572"/>, the 'active' endpoint will take
the TLS client role.
</t>
<t>
Once a DTLS connection has been established, if the 'active/passive' status of the
endpoints change (as result of an offer/answer transaction) during a session, a
new DTLS connection MUST be established. Therefore, endpoints SHOULD NOT change
the 'active/passive' status during a session, unless they want to establish a
new DTLS connection.
</t>
<t>
If the transport parameters or the key fingerprints change, the endpoints
MUST establish a new DTLS connection. In such case the 'active/passive'
status of the endpoints will again be determined following the procedures
in <xref target="RFC4145"/>, and the new status will be used to determine the
TLS roles of the endpoints associated with the new DTLS connection.
</t>
<t>
NOTE: The procedure above is identical to the one defined for SRTP-DTLS in
<xref target="RFC5763"/>.
</t>
</section>
</section>
<section title="SDP connection Attribute" anchor="sec-attributes-connection">
<t>
The SDP connection attribute is used following the procedures in
<xref target="RFC4145"/>, with the additional SCTP specific
considerations described in this section.
</t>
<t>
If the m- line proto value is 'TCP/DTLS/SCTP', an SDP connection
attribute associated with that m- line applies to both the
SCTP association and the TCP connection. Therefore, an
attribute 'new' value indicates that both a new SCTP association,
and a new TCP connection, have to be established,
following the procedures in <xref target="RFC4145"/>.
</t>
<t>
NOTE: This specification does not define a mechanism which allows
re-establishing of a new SCTP association, while maintaining the
TCP connection.
</t>
<t>
The SDP connection attribute value does not automatically impact
an existing DTLS connection. <xref target="sec-attributes-setup-tls"/>
describes in which cases a new DTLS connections will be established.
</t>
<t>
NOTE: If the m- line proto value is 'SCTP/DTLS', and if the
SCTP association is re-established, the DTLS connection also needs
to be re-established.
</t>
</section>
</section>
<section title="SDP Offer/Answer Procedures">
<section title="General">
<t>
This section defines the SDP Offer/Answer <xref target="RFC3264"/>
procedures for negotiating and establishing an SCTP association. Unless
explicitly stated, the procedures apply to all m- line proto values
('SCTP', 'SCTP/DTLS', 'UDP/DTLS/SCTP' and 'TCP/DTLS/SCTP') defined
in this specification.
</t>
<t>
If the m- line proto value is 'SCTP/DTLS', 'UDP/DTLS/SCTP' or 'TCP/DTLS/SCTP',
each endpoint MUST provide a certificate fingerprint, using the SDP 'fingerprint'
attribute <xref target="RFC4572"/>, if the endpoint supports, and is willing to use,
a cipher suite with an associated certificate.
</t>
<t>
The authentication certificates are interpreted and validated as
defined in <xref target="RFC4572"/>. Self-signed certificates can
be used securely, provided that the integrity of the SDP description
is assured as defined in <xref target="RFC4572"/>.
</t>
<t>
NOTE: The procedures apply to a specific m- line describing an SCTP association.
If an offer or answer contains multiple m- lines describing SCTP associations,
the procedures are applied separately to each m- line.
</t>
</section>
<section title="Generating the Initial SDP Offer" anchor="sec-oa-initial-offer">
<t>
When the offerer creates an initial offer, the offerer:
</t>
<t>
<list style="symbols">
<t>
MUST, if the m- line proto value is 'SCTP/DTLS', 'UDP/DTLS/SCTP' or 'TCP/DTLS/SCTP',
associate an SDP setup attribute [<xref target="sec-attributes-setup" />],
with an 'actpass' value, with the m- line;
</t>
<t>
MUST, if the m- line proto is 'UDP/DTLS/SCTP' or 'TCP/DTLS/SCTP', associate an
SDP 'sctp-port' attribute [<xref target="attr-sctp-port" />] with the m- line;
</t>
<t>
MUST associate an SDP 'connection' attribute [<xref target="sec-attributes-connection" />],
with a 'new' value, with the m- line; and
</t>
<t>
MAY associate an SDP 'max-message-size' attribute [<xref target="attr-max-message-size" />]
with the m- line.
</t>
</list>
</t>
</section>
<section title="Generating the SDP Answer">
<t>
When the answerer receives an offer, which contains an m- line describing
an SCTP association, if the answerer accepts the m- line it:
</t>
<t>
<list style="symbols">
<t>
MUST insert a corresponding m- line in the answer, with an identical
m- line proto value <xref target="RFC3264"/>;
</t>
<t>
MUST, if the m- line proto value is 'SCTP/DTLS', 'UDP/DTLS/SCTP' or 'TCP/DTLS/SCTP',
associate an SDP 'setup' attribute [<xref target="sec-attributes-setup" />],
with an 'active' or 'passive' value, with the m- line;
</t>
<t>
MUST, if the m- line proto is 'UDP/DTLS/SCTP' or 'TCP/DTLS/SCTP', associate an
SDP 'sctp-port' attribute[<xref target="attr-sctp-port" />] with the m- line; and
</t>
<t>
MAY associate an SDP 'max-message-size' attribute [<xref target="attr-max-message-size" />]
with the m- line.
</t>
</list>
</t>
<t>
Once the answerer has sent the answer, the answerer:
</t>
<t>
<list style="symbols">
<t>
MUST, if an SCTP association associated with the m- line has yet not
been established, or if an existing SCTP association is to be re-established,
initiate the establishing of the SCTP association; and
</t>
<t>
MUST, if the answerer is the 'active' endpoint, and if an DTLS connection associated
with the m- line is to be established (or re-established), initiate the establishing
of the DTLS connection (by sending a ClientHello message).
</t>
</list>
</t>
<t>
If the answerer does not accept the m- line in the offer, it MUST assign a zero port value
to the corresponding m- line in the answer. In addition, the answerer MUST NOT establish an
SCTP association, or a DTLS connection, associated with the m- line.
</t>
</section>
<section title="Offerer Processing of the SDP Answer">
<t>
When the offerer receives an answer, which contains an m- line with a non-zero
port value, describing an SCTP association, the offerer:
</t>
<t>
<list style="symbols">
<t>
MUST, if the offerer is the 'active' endpoint, if the m- line proto
is 'TCP/DTLS/SCTP', and if a TCP connection used to carry the SCTP association
has yet not been established (or if an existing TCP connection is to be re-established),
initiate the establishing of the TCP connection;
</t>
<t>
MUST, if an SCTP association associated with the m- line has yet not
been established (or if an existing SCTP association is to be re-established),
initiate the establishing of the SCTP association; and
</t>
<t>
MUST, if the offerer is the 'active' endpoint, and if an DTLS connection associated
with the m- line is to be established (or if an existing DTLS connection is to be
re-established), initiate the establishing of the DTLS connection (by sending a
ClientHello message).
</t>
</list>
</t>
<t>
If the m- line in the answer contains a zero port value, the offerer MUST NOT
establish a TCP connection, an SCTP association, or a DTLS connection, associated with
the m- line.
</t>
</section>
<section title="Modifying the Session">
<t>
When an offerer sends an updated offer, in order to modify a previously established
SCTP association, it follows the procedures in <xref target="sec-oa-initial-offer" />, with
the following exceptions:
</t>
<t>
<list style="symbols">
<t>
Unless the offerer wants to re-establish an existing SCTP association, the offerer
MUST associate an SDP connection attribute, with an 'existing' value, with the
m- line; and
</t>
<t>
If the offerer wants to disable a previously established SCTP association, it MUST
assign a zero port value to the m- line associated with the SCTP association, following
the procedures in <xref target="RFC3264"/>.
</t>
</list>
</t>
<t>
NOTE: Different SCTP association usages might define protocol procedures etc that
need to be performed before an SCTP association is terminated. Such procedures are
outside the scope of this specification.
</t>
</section>
</section>
<section title="Multihoming Considerations">
<t>
SCTP supports multihoming. An SCTP endpoint is considered
multihomed if it has more than one IP address on which SCTP
can be used. An SCTP endpoint inform the remote peer about
its IP addresses using the address parameters in the INIT/INIT-ACK
chunk. Therefore, when SDP is used to describe an SCTP association,
while the "c=" line contains the address which was used to negotiate
the SCTP association, multihomed SCTP endpoints might end up using
other IP addresses.
</t>
<t>
If an endpoint removes the IP address <xref target="RFC5061"/> that
it offered in the SDP "c=" line associated with the SCTP association,
it MUST send a new Offer, in which the "c=" line contains an IP address
with is valid within the SCTP association.
</t>
<t>
NOTE: In some network environments, intermediaries performing gate-
and firewall control use the address information in the SDP "c=" and
"m=" lines to authorize media, and will not pass media sent using
other addresses. In such network environment, if an SCTP endpoints
wants to change the address information on which media is sent and
received, it needs to send an updated Offer, in which the SDP "c="
and "m=" lines contain the new address information.
</t>
<t>
Multihoming is not supported when sending SCTP on top of DTLS,
as DTLS does not expose address management to its upper layer.
</t>
</section>
<section title="NAT Considerations">
<section title="General">
<t>
SCTP features not present in UDP or TCP, including the checksum
(CRC32c) value calculated on the whole packet (rather than
just the header), and multihoming, introduce new challenges
for NAT traversal. <xref target="I-D.ietf-behave-sctpnat"/>
defines an SCTP specific variant of NAT, which provides similar
features of Network Address and Port Translation (NAPT).
</t>
<t>
Current NATs typically do not support SCTP. <xref target="RFC6951"/>
defines a mechanism for sending SCTP on top of UDP, which makes it
possible to use SCTP with NATs and firewalls that do not support SCTP.
</t>
</section>
<section title="ICE Considerations">
<t>
At the time of writing this specification, no procedures have been
defined for using ICE (Interactive Connectivity Establishment)
<xref target="RFC5768"/> together with SCTP. Such procedures, including
the associated SDP Offer/Answer procedures, are outside the scope of
this specification, and might be defined in a future specification.
</t>
</section>
</section>
<section title="Examples">
<section title="Establishment of UDP/DTLS/SCTP association">
<figure>
<artwork><![CDATA[
SDP Offer:
m=application 54111 UDP/DTLS/SCTP webrtc-datachannel
c=IN IP4 192.0.2.1
a=setup:actpass
a=connection:new
a=sctp-port:5000
a=max-message-size: 100000
- The offerer indicates that the usage of the
UDP/DTLS/SCTP association will be as defined
for the 'webrtc-datachannel' format value.
- The offerer UDP port value is 54111.
- The offerer SCTP port value is 5000.
- The offerer indicates that it can take either the
active or the passive role.
SDP Answer:
m=application 64300 UDP/DTLS/SCTP webrtc-datachannel
c=IN IP4 192.0.2.2
a=setup:passive
a=sctp-port:6000
a=max-message-size: 100000
- The answerer UDP port value is 64300.
- The answerer SCTP port value is 6000.
- The answerer takes the passive role.
]]></artwork>
</figure>
</section>
</section>
<section title="Security Considerations">
<t>
<xref target="RFC4566"/> defines general SDP security considerations, while
<xref target="RFC3264"/>, <xref target="RFC4145"/> and <xref target="RFC4572"/>
define security considerations when using the SDP offer/answer mechanism
to negotiate media streams.
</t>
<t>
<xref target="RFC4960"/> defines general SCTP security considerations.
security considerations on SCTP in general, while <xref target="RFC6083"/>
defines security considerations when using DTLS on top of
SCTP.
</t>
<t>
This specification does not introduce new security considerations in addition
to those defined in the specifications listed above.
</t>
</section>
<section title="IANA Considerations">
<section title="New SDP proto values" anchor="iana-sdp-proto" toc="default">
<t>
[RFC EDITOR NOTE: Please replace RFCXXXX with the RFC number
of this document.]
</t>
<t>
This document updates the "Session Description Protocol (SDP) Parameters" registry,
following the procedures in <xref target="RFC4566" pageno="false" format="default"/>,
by adding the following values to the table in the SDP "proto" field registry:
</t>
<texttable anchor="table_SDP_proto_values" title='SDP "proto" field values'>
<ttcol align='center'>Type</ttcol>
<ttcol align='center'>SDP Name</ttcol>
<ttcol align='center'>Reference</ttcol>
<c>proto</c>
<c>SCTP</c>
<c>[RFCXXXX]</c>
<c>proto</c>
<c>SCTP/DTLS</c>
<c>[RFCXXXX]</c>
<c>proto</c>
<c>UDP/DTLS/SCTP</c>
<c>[RFCXXXX]</c>
<c>proto</c>
<c>TCP/DTLS/SCTP</c>
<c>[RFCXXXX]</c>
</texttable>
</section>
<section title="New SDP Attributes" anchor="iana-sdp-attr" toc="default">
<section title="sctp-port" anchor="iana-sdp-attr-sctp-port" toc="default">
<t>
[RFC EDITOR NOTE: Please replace RFCXXXX with the RFC number
of this document.]
</t>
<t>
This document defines a new SDP media-level attribute,'sctp-port', as follows:
</t>
<figure>
<artwork align="left"><![CDATA[
Attribute name: sctp-port
Type of attribute: media
Subject to charset: No
Purpose: Indicate the SCTP port value associated
with the SDP Media Description.
Appropriate values: Integer
Contact name: Christer Holmberg
Contact e-mail: christer.holmberg@ericsson.com
Reference: RFCXXXX
]]></artwork>
</figure>
</section>
<section title="max-message-size" anchor="iana-sdp-attr-max-msg-size" toc="default">
<t>
[RFC EDITOR NOTE: Please replace RFCXXXX with the RFC number
of this document.]
</t>
<t>
This document defines a new SDP media-level attribute,'max-message-size', as follows:
</t>
<figure>
<artwork align="left"><![CDATA[
Attribute name: max-message-size
Type of attribute: media
Subject to charset: No
Purpose: Indicate the maximum message size that
an SCTP endpoint is willing to receive
on the SCTP association associated
with the SDP Media Description.
Appropriate values: Integer
Contact name: Christer Holmberg
Contact e-mail: christer.holmberg@ericsson.com
Reference: RFCXXXX
]]></artwork>
</figure>
</section>
</section>
<section title="association-usage Name Registry" anchor="iana-assusage-registry" toc="default">
<t>
[RFC EDITOR NOTE: Please replace RFCXXXX with the RFC number
of this document.]
</t>
<t>
This specification creates a new IANA registry, following the procedures in
<xref target="RFC5226"/>, for the "fmt" namespace associated with the
'SCTP', 'SCTP/DTLS', 'UDP/DTLS/SCTP' and 'TCP/DTLS/SCTP' protocol identifiers.
Each "fmt" value describes the usage of an entire SCTP association, including
all SCTP streams associated with the SCTP association.
</t>
<t>
NOTE: Usage indication of individual SCTP streams is outside the scope of this
specification.
</t>
<t>
The "fmt" value, "association-usage", used with these "proto" is required.
It is defined in [<xref target="m-line"/>].
</t>
<t>
As part of this registry, IANA maintains the following information:
</t>
<t>
<list style='hanging'>
<t hangText="association-usage name:">.The identifier of the
subprotocol, as will be used as the "fmt" value.</t>
<t hangText="association-usage reference:">A reference to the
document in which the association-usage is defined.</t>
</list>
</t>
<t>
association-usage names are to be subject to the "First Come First Served"
IANA registration policy [RFC5226].
</t>
<t>
IANA is asked to add initial values to the registry.
</t>
<figure anchor="exempleIANA" title="">
<artwork><![CDATA[
| name | Reference |
-+--------------------+-------------------------------------+
| webrtc-datachannel | draft-ietf-rtcweb-data-protocol-xx |
-+----------------------------------------------------------|
]]></artwork>
</figure>
</section>
</section>
<section title="Acknowledgments">
<t>
The authors wish to thank Harald Alvestrand, Randell Jesup, Paul Kyzivat,
Michael Tuexen for their comments and useful feedback.
</t>
</section>
<section title="Change Log">
<t>[RFC EDITOR NOTE: Please remove this section when publishing]</t>
<t>Changes from draft-ietf-mmusic-sctp-sdp-11
<list style="symbols">
<t>Example added.</t>
</list>
</t>
<t>Changes from draft-ietf-mmusic-sctp-sdp-10
<list style="symbols">
<t>SDP max-message-size attribute added to IANA considerations.</t>
<t>Changes based on comments from Paul Kyzivat:</t>
<t>- Text about max message size removed from fmtp attribute section.</t>
</list>
</t>
<t>Changes from draft-ietf-mmusic-sctp-sdp-09
<list style="symbols">
<t>'DTLS/SCTP' split into 'UDP/DTLS/SCTP' and 'TCP/DTLS/SCTP'</t>
<t>Procedures for realizing UDP/DTLS/SCTP- and TCP/DTLS/SCTP transports added.</t>
</list>
</t>
<t>Changes from draft-ietf-mmusic-sctp-sdp-08
<list style="symbols">
<t>Default SCTP port removed:</t>
<t>- Usage of SDP sctp-port attribute mandatory.</t>
<t>SDP max-message-size attribute defined:</t>
<t>- Attribute definition.</t>
<t>- SDP Offer/Answer procedures.</t>
<t>Text about SDP direction attributes added.</t>
<t>Text about TLS role determination added.</t>
</list>
</t>
</section>
</middle>
<back>
<references title="Normative References">
<?rfc include="reference.RFC.2119"?>
<?rfc include="reference.RFC.3264"?>
<?rfc include="reference.RFC.4145"?>
<?rfc include="reference.RFC.4289"?>
<?rfc include="reference.RFC.4566"?>
<?rfc include="reference.RFC.4571"?>
<?rfc include="reference.RFC.4572"?>
<?rfc include="reference.RFC.4960"?>
<?rfc include="reference.RFC.5061"?>
<?rfc include="reference.RFC.5226"?>
<?rfc include="reference.RFC.5246"?>
<?rfc include="reference.RFC.6347"?>
<?rfc include="reference.RFC.6838"?>
<?rfc include="reference.I-D.draft-ietf-tsvwg-sctp-dtls-encaps-06"?>
</references>
<references title="Informative References">
<?rfc include="reference.RFC.5763"?>
<?rfc include="reference.RFC.5768"?>
<?rfc include="reference.RFC.6083"?>
<?rfc include="reference.RFC.6951"?>
<?rfc include="reference.I-D.draft-ietf-behave-sctpnat-09"?>
</references>
</back>
</rfc>
| PAFTECH AB 2003-2026 | 2026-04-23 20:44:19 |