One document matched: draft-ietf-ipfc-fcmgmt-int-mib-03.txt
Differences from draft-ietf-ipfc-fcmgmt-int-mib-02.txt
Blumenau [Page 01]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
o Emulex Corporation
o Exabyte Corporation
o G2 Networks
o Gadzoox Networks, Inc.
o Hewlett Packard Co.
o Interphase Corporation
o Jaycor Networks Inc.
o Legato Systems, Inc.
o McDATA Corporation
o Pathlight Technology, In.c
o Prisa Networks, Inc.
o QLogic Corporation
o Sequent Computer Systems, Inc.
o Siemens AG
o Softwaorks, Inc.
o Sterling Software, Inc.
o StorageNetworks, Inc.
o Transoft Networks, Inc.
o VERITAS Software Corporation
o Vixel Corporation
The MIB:
FCMGMT-MIB
-- Last edit date: Nov 10th, 1999
DEFINITIONS ::= BEGIN
IMPORTS
IpAddress, TimeTicks, experimental
FROM RFC1155-SMI
OBJECT-TYPE
FROM RFC-1212
DisplayString
FROM RFC1213-MIB
TRAP-TYPE
FROM RFC-1215;
---------------------------------------------------------------------
-- Textual conventions for this MIB
FcNameId ::= OCTET STRING (SIZE(8))
FcGlobalId ::= OCTET STRING (SIZE(16))
Blumenau [Page 02]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
FcEventSeverity ::= INTEGER {
unknown (1),
emergency (2),
alert (3),
critical (4),
error (5),
warning (6),
notify (7),
info (8),
debug (9),
mark (10) -- All messages logged
}
FcUnitType ::= INTEGER {
unknown(1),
other(2), -- none of the following
hub(3), -- passive connectivity unit
-- supporting loop protocol.
switch(4), -- active connectivity unit
-- supporting multiple protocols.
gateway(5), -- unit that converts not only
-- the interface but also encapsulates
-- the frame into another protocol. The
-- assumption is that there is always
-- two gateways connected together. For
-- example, FC <-> ATM.
converter(6), -- unit that converts from one
-- interface to another. For
-- example, FC <-> SCSI.
hba(7), -- host bus adapter
proxy-agent(8), -- software proxy-agent
storage-device(9), -- disk,cd,tape,etc
host(10), -- host computer
storage-subsystem(11), -- raid, library, etc
module(12), -- subcomponent of a system
swdriver(13), -- software driver
storage-access-device(14) -- Provides storage management
-- and access for hetergeneous
-- hosts and heterogeneous devices.
}
----------------------------------------------------------------------
fcmgmt OBJECT IDENTIFIER ::= { experimental 94 }
-- groups in fcmgmt
connSet OBJECT IDENTIFIER ::= { fcmgmt 1 }
trapReg OBJECT IDENTIFIER ::= { fcmgmt 2 }
statSet OBJECT IDENTIFIER ::= { fcmgmt 4 }
revisionNumber OBJECT-TYPE
SYNTAX DisplayString (SIZE (4))
ACCESS read-only
STATUS mandatory
Blumenau [Page 03]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
DESCRIPTION
"This is the revision number for this MIB. The
format of the revision value is as follows
(0) = high order major revision number
(1) = low order major revision number
(2) = high order minor revision number
(3) = low order minor revision number
The value will be stored as an ASCII value. The
following is the current value of this object.
(0) = '0'
(1) = '2'
(2) = '2'
(3) = '0'
This defines a revision of 02.20
"
::= { fcmgmt 3 }
-- the connectivity unit group
-- Implementation of the group is mandatory for all systems.
uNumber OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of connectivity units present on this
system (represented by this agent). May be a count
of the boards in a chassis or the number of full boxes
in a rack."
DEFVAL { 1 }
::= { connSet 1 }
systemURL OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The top-level URL of the system. If it does not exist
the value is empty string. The URL format is
implementation dependant and can have keywords embedded
that are preceeded by a percent sign (eg, %USER).
The following are the defined keywords that will
be recognized and replaced with data during a launch.
USER - replace with username
PASSWORD - replace with password
GLOBALID - replace with globalid
SERIALNO - replace with serial number
"
DEFVAL { "" }
::= { connSet 2 }
Blumenau [Page 04]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
statusChangeTime OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS deprecated
DESCRIPTION
"The sysuptime timestamp in centiseconds at which
the last status change occurred for any members of
the set."
::= { connSet 3 }
configurationChangeTime OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS deprecated
DESCRIPTION
"The sysuptime timestamp in centiseconds at which
the last configuration change occurred for any
members of the set. This represents a union of change
information for connUnitConfigurationChangeTime."
::= { connSet 4 }
connUnitTableChangeTime OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS deprecated
DESCRIPTION
"The sysuptime timestamp in centiseconds at which
the connUnitTable was updated (an entry was either
added or deleted."
::= { connSet 5 }
-- The Connectivity table contains general information on the
-- system's units.
connUnitTable OBJECT-TYPE
SYNTAX SEQUENCE OF ConnUnitEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of units under a single SNMP agent. The number
of entries is given by the value of uNumber. It is 1
for stand-alone system."
::= { connSet 6 }
connUnitEntry OBJECT-TYPE
SYNTAX ConnUnitEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A connectivity unit entry containing objects for a
particular unit."
INDEX { connUnitId }
::= { connUnitTable 1 }
Blumenau [Page 05]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
ConnUnitEntry ::=
SEQUENCE {
connUnitId
OCTET STRING,
connUnitGlobalId
FcGlobalId,
connUnitType
FcUnitType,
connUnitNumports
INTEGER,
connUnitState
INTEGER,
connUnitStatus
INTEGER,
connUnitProduct
DisplayString,
connUnitSn
DisplayString,
connUnitUpTime
TimeTicks,
connUnitUrl
DisplayString,
connUnitDomainId
OCTET STRING,
connUnitProxyMaster
INTEGER,
connUnitPrincipal
INTEGER,
connUnitNumSensors
INTEGER,
connUnitStatusChangeTime
TimeTicks,
connUnitConfigurationChangeTime
TimeTicks,
connUnitNumRevs
INTEGER,
connUnitNumZones
INTEGER,
connUnitModuleId
OCTET STRING,
connUnitName
DisplayString,
connUnitInfo
DisplayString,
connUnitControl
INTEGER,
connUnitContact
DisplayString,
connUnitLocation
DisplayString,
connUnitEventFilter
FcEventSeverity,
connUnitNumEvents
INTEGER,
Blumenau [Page 06]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
connUnitMaxEvents
INTEGER,
connUnitEventCurrID
INTEGER
}
connUnitId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (16))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The unique identification for this connectivity
unit among those within this proxy domain.
The value MUST be unique within the proxy domain
because it is the index variable for connUnitTable.
The value assigned to a given conectivity unit
SHOULD be persistent across agent and unit resets.
It SHOULD be the same as connUnitGlobalId
if connUnitGlobalId is known and stable."
::= { connUnitEntry 1 }
connUnitGlobalId OBJECT-TYPE
SYNTAX FcGlobalId
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An optional global-scope identifier for this
connectivity unit.
It MUST be a WWN for this connectivity unit
or 16 octets of value zero.
WWN formats requiring fewer than 16 octets
MUST be extended to 16 octets with trailing zero
octets. If a WWN is used for connUnitId,
the same WWN MUST be used for connUnitGlobalId.
When a non-zero value is provided,
it SHOULD be persistent across agent and unit resets.
It SHOULD be globally unique.
It SHOULD be one of these FC-PH/PH3 formats:
IEEE (NAA=1)
IEEE Extended (NAA=2)
IEEE Registered (NAA=5).
IEEE Registered extended (NAA=6).
Use of the IEEE formats allows any IEEE-registered
vendor to assure global uniqueness independently.
The following are some references on IEEE WWN formats:
http://standards.ieee.org/regauth/oui/tutorials/fibreformat.html
http://standards.ieee.org/regauth/oui/tutorials/fibrecomp_id.html
If one or more WWNs are associated with the connUnit
via other management methods,
one of them SHOULD be used for connUnitGlobalId.
If there is not a WWN assigned specifically to the
connUnit,there is some merit, though not a requirement,
Blumenau [Page 07]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
to using a WWN assigned to (one of)
its permanently attached FC/LAN interface(s).
This can not risk uniqueness, though.
As a counterexample, if your
agent runs in a host and the host has an HBA,
it is quite possible that agent, host, and HBA
will all be distinct connUnits, so the host
and agent can not use the WWN of the HBA.
Another example:
If your hub has a built-in Ethernet port, it
might be reasonable for the hub to use its LAN
address (prefixed with the appropriate
NAA) as its connUnitId. But if the
Ethernet were a replaceable PCCard, the hub
should have an independent ID."
::= { connUnitEntry 2 }
connUnitType OBJECT-TYPE
SYNTAX FcUnitType
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The type of this connectivity unit."
::= { connUnitEntry 3 }
connUnitNumports OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of physical ports in the connectivity unit
(internal/embedded, external)."
::= { connUnitEntry 4 }
connUnitState OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
online(2),
offline(3)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Overall state of the connectivity unit."
::= { connUnitEntry 5 }
connUnitStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
unused(2),
ok(3),
warning(4), -- needs attention
Blumenau [Page 08]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
failed(5)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Overall status of the connectivity unit."
::= { connUnitEntry 6 }
connUnitProduct OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..79))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The connectivity unit vendor's product
model name."
::= { connUnitEntry 7 }
connUnitSn OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..79))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The serial number for this connectivity unit."
::= { connUnitEntry 8 }
connUnitUpTime OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of centiseconds since the
last unit initialization."
::= { connUnitEntry 9 }
connUnitUrl OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"URL to launch a management application,
if applicable. Otherwise empty string.
In a standalone unit, this would be the
same as the top-level URL. This has the same
definition as systemURL for keywords."
::= { connUnitEntry 10 }
connUnitDomainId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(3))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"24 bit Fibre Channel address ID of this
connectivity unit, right justified with leading
Blumenau [Page 09]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
zero's if required. If this value is not applicable,
return all bits set to one."
::= { connUnitEntry 11 }
connUnitProxyMaster OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
no(2),
yes(3)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A value of 'yes' means this is the proxy master
unit for a set of managed units. For example,
this could be the only unit with a management
card in it for a set of units. A standalone unit
should return 'yes' for this object."
::= { connUnitEntry 12 }
connUnitPrincipal OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
no(2),
yes(3)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Whether this connectivity unit is the principal unit
within the group of fabric elements. If this value
is not applicable, return unknown."
::= { connUnitEntry 13 }
connUnitNumSensors OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of sensors in the connUnitSensorTable."
::= { connUnitEntry 14 }
connUnitStatusChangeTime OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS deprecated
DESCRIPTION
"The sysuptime timestamp in centiseconds
at which the last status change occurred."
::= { connUnitEntry 15 }
connUnitConfigurationChangeTime OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
Blumenau [Page 10]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
STATUS deprecated
DESCRIPTION
"The sysuptime timestamp in centiseconds
at which the last configuration change
occurred."
::= { connUnitEntry 16 }
connUnitNumRevs OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of revisions in the connUnitRevsTable."
DEFVAL { 1 }
::= { connUnitEntry 17 }
connUnitNumZones OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS deprecated
DESCRIPTION
"Number of zones defined in connUnitZoneTable."
::= { connUnitEntry 18 }
connUnitModuleId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(16))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This is a unique id, persistent between boots,
that can be used to group a set of connUnits
together into a module. The intended use would
be to create a connUnit with a connUnitType of
'module' to represent a physical or logical
group of connectivity units. Then the value
of the group would be set to the value of
connUnitId for this 'container' connUnit.
connUnitModuleId should be zeros if this
connUnit is not part of a module."
::= { connUnitEntry 19 }
connUnitName OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..79))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"A display string containing a name for this
connectivity unit. This object value should be
persistent between boots."
::= { connUnitEntry 20 }
connUnitInfo OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
Blumenau [Page 11]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
STATUS mandatory
DESCRIPTION
"A display string containing information
about this connectivity unit. This object value
should be persistent between boots."
::= { connUnitEntry 21 }
connUnitControl OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
invalid(2),
resetConnUnitColdStart(3),
resetConnUnitWarmStart(4),
offlineConnUnit(5),
onlineConnUnit(6)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object is used to control the addressed
connUnit.
NOTE: 'Cold Start' and 'Warm Start'
are as defined in MIB II and are not meant
to be a factory reset.
resetConnUnitColdStart:
the addressed unit performs
a 'Cold Start' reset.
resetConnUnitWarmStart:
the addressed unit performs
a 'Warm Start' reset.
offlineConnUnit:
the addressed unit puts itself into
an implementation dependant 'offline' state.
In general,if a unit is in an offline state,
it cannot be used to perform meaningful
Fibre Channel work.
onlineConnUnit:
the addressed unit puts itself into an
implementation dependant 'online' state.
In general, if a unit is in an online state,
it is capable of performing meaningful
Fibre Channel work.
NOTE: Each implementation may chose not to allow
any or all of these values on a SET. "
::= { connUnitEntry 22 }
Blumenau [Page 12]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
connUnitContact OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..79))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Contact information for this connectivity
unit."
::= { connUnitEntry 23 }
connUnitLocation OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..79))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Location information for this connectivity
unit."
::= { connUnitEntry 24 }
connUnitEventFilter OBJECT-TYPE
SYNTAX FcEventSeverity
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This value defines the event severity
that will be logged by this connectivity unit.
All events of severity less than or equal to
connUnitEventFilter are logged in connUnitEventTable."
::= { connUnitEntry 25 }
connUnitNumEvents OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of events currently in the
connUnitEventTable."
::= { connUnitEntry 26 }
connUnitMaxEvents OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Max number of events that can be defined
in connUnitEventTable."
::= { connUnitEntry 27 }
connUnitEventCurrID OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The last used event id (connUnitEventId)."
::= { connUnitEntry 28 }
Blumenau [Page 13]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
------------------------------------------------------------------
-- The Table of revisions for hardware and software elements.
connUnitRevsTable OBJECT-TYPE
SYNTAX SEQUENCE OF ConnUnitRevsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Table of the revisions supported by
connectivity units managed by this agent."
::= { connSet 7 }
connUnitRevsEntry OBJECT-TYPE
SYNTAX ConnUnitRevsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { connUnitRevsUnitId,
connUnitRevsIndex }
::= { connUnitRevsTable 1 }
ConnUnitRevsEntry ::=
SEQUENCE {
connUnitRevsUnitId
OCTET STRING,
connUnitRevsIndex
INTEGER,
connUnitRevsRevId
DisplayString,
connUnitRevsDescription
DisplayString }
connUnitRevsUnitId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (16))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The connUnitId of the connectivity unit
that contains this revision table."
::= { connUnitRevsEntry 1 }
connUnitRevsIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value among all connUnitRevsEntrys
with the same value of connUnitRevsUnitId,
in the range between 1 and
connUnitNumRevs[connUnitRevsUnitId]."
::= { connUnitRevsEntry 2 }
Blumenau [Page 14]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
connUnitRevsRevId OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A vendor-specific string identifying a
revision of a component of the connUnit
indexed by connUnitRevsUnitId."
::= { connUnitRevsEntry 3 }
connUnitRevsDescription OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Description of a component to which the revision
corresponds."
::= { connUnitRevsEntry 4 }
-----------------------------------------------------------------------
-- The Sensor table
connUnitSensorTable OBJECT-TYPE
SYNTAX SEQUENCE OF ConnUnitSensorEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Table of the sensors supported by each
connectivity unit managed by this agent."
::= { connSet 8 }
connUnitSensorEntry OBJECT-TYPE
SYNTAX ConnUnitSensorEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Each entry contains the information for a
specific sensor."
INDEX { connUnitSensorUnitId,
connUnitSensorIndex }
::= { connUnitSensorTable 1 }
ConnUnitSensorEntry ::=
SEQUENCE {
connUnitSensorUnitId
OCTET STRING,
connUnitSensorIndex
INTEGER (1..2147483647),
connUnitSensorName
DisplayString,
connUnitSensorStatus
INTEGER,
connUnitSensorInfo
DisplayString,
Blumenau [Page 15]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
connUnitSensorMessage
DisplayString,
connUnitSensorType
INTEGER,
connUnitSensorCharacteristic
INTEGER
}
connUnitSensorUnitId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (16))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The connUnitId of the connectivity unit
that contains this sensor table."
::= { connUnitSensorEntry 1 }
connUnitSensorIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value among all connUnitSensorEntrys
with the same value of connUnitSensorUnitId,
in the range between 1 and
connUnitNumSensor[connUnitSensorUnitId]."
::= { connUnitSensorEntry 2}
connUnitSensorName OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A textual identification of the sensor
intended primarily for operator use."
::= { connUnitSensorEntry 3 }
connUnitSensorStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
other(2),
ok(3), -- the sensor indicates ok
warning(4), -- the sensor indicates a warning
failed(5) -- the sensor indicates failure
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The status indicated by the sensor."
::= { connUnitSensorEntry 4 }
connUnitSensorInfo OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
Blumenau [Page 16]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
STATUS mandatory
DESCRIPTION
"Miscellaneous static info about the sensor
such as its serial number."
::= { connUnitSensorEntry 5 }
connUnitSensorMessage OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This describes the status of the sensor
as a message. It may also provide more
resolution on the sensor indication, for
example 'Cover temperature 1503K, above
nominal operating range'"
::= { connUnitSensorEntry 6 }
connUnitSensorType OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
other(2),
battery(3),
fan(4),
power-supply(5),
transmitter(6),
enclosure(7),
board(8),
receiver(9)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The type of component being monitored by this
sensor."
::= { connUnitSensorEntry 7 }
connUnitSensorCharacteristic OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
other(2),
temperature(3),
pressure(4),
emf(5),
currentValue(6), -- current is a keyword
airflow(7),
frequency(8),
power(9)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The characteristics being monitored by this
sensor."
::= { connUnitSensorEntry 8 }
Blumenau [Page 17]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
-----------------------------------------------------------------------
-- The port table
connUnitPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF ConnUnitPortEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Generic information on ports for a specific
connUnit."
::= { connSet 10 }
connUnitPortEntry OBJECT-TYPE
SYNTAX ConnUnitPortEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Each entry contains the information for
a specific port."
INDEX { connUnitPortUnitId,
connUnitPortIndex }
::= { connUnitPortTable 1 }
ConnUnitPortEntry ::=
SEQUENCE {
connUnitPortUnitId
OCTET STRING,
connUnitPortIndex
INTEGER,
connUnitPortType
INTEGER,
connUnitPortFCClassCap
OCTET STRING,
connUnitPortFCClassOp
OCTET STRING,
connUnitPortState
INTEGER,
connUnitPortStatus
INTEGER,
connUnitPortTransmitterType
INTEGER,
connUnitPortModuleType
INTEGER,
connUnitPortWwn
FcNameId,
connUnitPortFCId
OCTET STRING,
connUnitPortSn
DisplayString,
connUnitPortRevision
DisplayString,
connUnitPortVendor
DisplayString,
Blumenau [Page 18]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
connUnitPortSpeed
INTEGER,
connUnitPortControl
INTEGER,
connUnitPortName
DisplayString,
connUnitPortPhysicalNumber
INTEGER,
connUnitPortStatObject
OBJECT IDENTIFIER
}
connUnitPortUnitId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (16))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The connUnitId of the connectivity unit
that contains this port."
::= { connUnitPortEntry 1 }
connUnitPortIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value among all connUnitPortEntrys
on this connectivity unit, between 0 and
connUnitNumPort[connUnitPortUnitId]."
::= { connUnitPortEntry 2 }
connUnitPortType OBJECT-TYPE
SYNTAX INTEGER {
unknown (1),
other (2),
not-present (3),
hub-port (4),
n-port (5), -- end port for fabric
l-port (6), -- end port for loop
fl-port (7), -- public loop
f-port (8), -- fabric port
e-port (9), -- fabric expansion port
g-port (10), -- generic fabric port
domain-ctl (11), -- domain controller
hub-controller(12),
scsi (13), -- parallel SCSI port
escon (14),
lan (15),
wan (16)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The port type."
::= { connUnitPortEntry 3 }
Blumenau [Page 19]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
connUnitPortFCClassCap OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (2))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Bit mask that specifies the classes
of service capability of this port. If this is not
applicable, return all bits set to zero.
The bits have
the following definition:
unknown - 0
class-f - 1
class-one - 2
class-two - 4
class-three - 8
class-four - 16
class-five - 32
class-six - 64"
::= { connUnitPortEntry 4 }
connUnitPortFCClassOp OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (2))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Bit mask that specifies the classes
of service that are currently operational.
If this is not applicable, return all bits
set to zero. This object has the same
definition as connUnitPortFCClassCap"
::= { connUnitPortEntry 5 }
connUnitPortState OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
online(2),
offline(3),
bypassed(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The state of the port hardware."
::= { connUnitPortEntry 6 }
connUnitPortStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown (1),
unused (2),
ok (3),
warning (4), -- needs attention
failure (5),
notparticipating (6),
Blumenau [Page 20]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
initializing (7),
bypass (8) -- manually or automatically
-- isolated from loop or fabric
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An overall protocol status for the
port."
::= { connUnitPortEntry 7 }
connUnitPortTransmitterType OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
other(2),
unused(3),
shortwave(4),
longwave(5),
copper(6),
scsi(7),
longwaveNoOFC(8),
shortwaveNoOFC(9),
longwaveLED(10)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The technology of the port transceiver."
::= { connUnitPortEntry 8 }
connUnitPortModuleType OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
other(2),
gbic(3),
embedded(4), -- fixed, ie, oneXnine
glm(5),
gbicSerialId(6),
gbicNoSerialId(7),
gbicNotInstalled(8),
smallFormFactor(9)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The module type of the port connector."
::= { connUnitPortEntry 9 }
connUnitPortWwn OBJECT-TYPE
SYNTAX FcNameId
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The World Wide Name of the port
Blumenau [Page 21]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
if applicable, otherwise empty string."
::= { connUnitPortEntry 10 }
connUnitPortFCId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(3))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This is the assigned Fibre Channel ID of
this port. This value is expected to be
a Big Endian value of 24 bits. If this is
loop, then it is the ALPA that is connected.
If this is an eport, then it will only
contain the domain ID left justified, zero
filled. If this port does not have a Fibre
Channel address, return all bits set to 1."
::= { connUnitPortEntry 11 }
connUnitPortSn OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..79))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The serial number of the unit (e.g., for
a GBIC). If this is not applicable, return
empty string."
::= { connUnitPortEntry 12 }
connUnitPortRevision OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..79))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The port revision (e.g., for a GBIC)."
::= { connUnitPortEntry 13 }
connUnitPortVendor OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..79))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The port vendor (e.g., for a GBIC)."
::= { connUnitPortEntry 14 }
connUnitPortSpeed OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The speed of the port in kilobytes per
second."
::= { connUnitPortEntry 15 }
Blumenau [Page 22]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
connUnitPortControl OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
invalid(2),
resetConnUnitPort(3),
bypassConnUnitPort(4),
unbypassConnUnitPort(5),
offlineConnUnitPort(6),
onlineConnUnitPort(7),
resetConnUnitPortCounters(8)
}
ACCESS read-write -- (or maybe write-only)
STATUS mandatory
DESCRIPTION
"This object is used to control the addressed
connUnit's port. Valid commands are:
resetConnUnitPort: If the addressed connUnit
allows this operation to be performed to this
port, the addressed port performs a
vendor-specific 'reset' operation. Examples of
these operations are: the Link Reset protocol,
the Loop Initialization protocol, or a
resynchronization occurring between the
transceiver in the addressed port to the
transceiver that the port is connected to.
bypassConnUnitPort: If the addressed connUnit
allows this operation to be performed to this
port, the addressed port performs a
vendor-specific 'bypass' operation. Examples of
these operations are:
transitioning from online to offline, a
request(NON-PARTICIPATING) command to the
Loop Port state machine, or removal of the
port from an arbitrated loop by a hub.
unbypassConnUnitPort: If the addressed connUnit
allows this operation to be performed to this
port, the addressed port performs a
vendor-specific 'unbypass' operation. Examples
of these operations are:
the Link Failure protocol, a
request(PARTICIPATING) command to the
Loop Port state machine, or addition of the
port to an arbitrated loop by a hub.
offlineConnUnitPort: If the addressed connUnit
allows this operation to be performed to this
port, the addressed port performs a
vendor-specific 'offline' operation. Examples
of these operations are:
disabling a port's transceiver, the Link
Failure protocol, request(NON-PARTICIPATING)
Blumenau [Page 23]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
command to the Loop Port state machine, or
removal of the port from an arbitrated loop
by a hub.
onlineConnUnitPort: If the addressed connUnit
allows this operation to be performed to this
port, the addressed port performs a
vendor-specific 'online' operation. Examples
of these operations are:
enabling a port's transceiver, the Link
Failure protocol, request(PARTICIPATING)
command to the Loop Port state machine, or
addition of the port from an arbitrated loop
by a hub.
NOTE: Each implementation may chose not to allow
any or all of these values on a SET. "
::= { connUnitPortEntry 16 }
connUnitPortName OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"A string describing the addressed port."
::= { connUnitPortEntry 17 }
connUnitPortPhysicalNumber OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This is the internal port number this
port is known by. In many implementations,
this should be the same as connUnitPortIndex.
Some implementations may have an internal port
representation not compatible with the rules
for table indeces. In that case, provide the
internal representation of this port in this
object. This value may also be used in the
connUnitLinkPortNumberX or connUnitLinkPortNumberY
objects of the connUnitLinkTable."
::= { connUnitPortEntry 18 }
connUnitPortStatObject OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This contains the OID of the first object of the
table that contains the statistics for this particular
port. If this has a value of zero, then there are no
statistics available for this port. The port type
Blumenau [Page 24]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
information will help identify the statistics objects
that will be found in the table. From this point, one
would do a getnext to get the next statistics object.
When the first part of the OID changes, the end of
table is reached."
::= { connUnitPortEntry 19 }
-----------------------------------------------------------------------
-- event group
connUnitEventTable OBJECT-TYPE
SYNTAX SEQUENCE OF ConnUnitEventEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The table of connectivity unit events. Errors,
warnings, and information should be reported
in this table."
::= { connSet 11 }
connUnitEventEntry OBJECT-TYPE
SYNTAX ConnUnitEventEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Each entry contains information on
a specific event for the given
connectivity unit."
INDEX { connUnitEventUnitId, connUnitEventIndex }
::= { connUnitEventTable 1 }
ConnUnitEventEntry ::=
SEQUENCE {
connUnitEventUnitId
OCTET STRING,
connUnitEventIndex
INTEGER (1..2147483647),
connUnitEventId
INTEGER,
connUnitREventTime
DisplayString,
connUnitSEventTime
TimeTicks,
connUnitEventSeverity
FcEventSeverity,
connUnitEventType
INTEGER,
connUnitEventObject
OBJECT IDENTIFIER,
connUnitEventDescr
DisplayString
}
Blumenau [Page 25]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
connUnitEventUnitId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (16))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The connUnitId of the connectivity unit
that contains this event table."
::= { connUnitEventEntry 1 }
connUnitEventIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Each connectivity unit has its own event buffer.
As it wraps, it may write over previous events.
This object is an index into the buffer.
It is recommended that this table be read using
'getNext's to retrieve the initial table.
The management application should read the
event table at periodic intervals and then
determine if any new entries were added by
comparing the last known index value with the
current highest index value. The management
application should then update its copy of
the event table. If the read interval
is too long, it is possible that there may
be events that may not be contained in the
agent's internal event buffer.
For example, an agent may read events 50-75.
At the next read interval, connUnitEventCurrID
is 189. If the management app tries to read
event index 76, and the agent's internal buffer
is 100 entries max, event index 76 will no longer
be available.
The index value is an incrementing integer starting
from one every time there is a table reset.
On table reset, all contents are emptied and
all indeces are set to zero. When an
event is added to the table, the event is
assigned the next higher integer value than
the last item entered into the table. If the
index value reaches its maximum value, the next
item entered will cause the index value to
roll over and start at one again."
::= { connUnitEventEntry 2 }
connUnitEventId OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS deprecated
DESCRIPTION
"The internal event Id. Incremented for each
event, ranging between 0 and connUnitMaxEvents.
Blumenau [Page 26]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
Not used as table index to simplify
the agent implementation. When this
reaches the end of the range specified by
connUnitMaxEvents, the Id will roll over to start
at zero. This value will be set back to zero at
reset. The relationship of this value to the index
is that internal event id may represent a smaller
number than a 32 bit integer (eg max 100 entries)
and would only have a value range up to
connUnitMaxEvents."
::= { connUnitEventEntry 3 }
connUnitREventTime OBJECT-TYPE
SYNTAX DisplayString (SIZE (15))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This is the real time when the event occurred.
It has the following format.
DDMMYYYY HHMMSS
DD=day number
MM=month number
YYYY=year number
HH=hour number
MM=minute number
SS=seconds number
If not applicable, return a NULL string."
::= { connUnitEventEntry 4 }
connUnitSEventTime OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This is the sysuptime timestamp when the
event occurred."
::= { connUnitEventEntry 5 }
connUnitEventSeverity OBJECT-TYPE
SYNTAX FcEventSeverity
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The event severity level."
::= { connUnitEventEntry 6 }
connUnitEventType OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
other(2),
status(3),
configuration(4),
topology(5)
}
Blumenau [Page 27]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The type of this event."
::= { connUnitEventEntry 7 }
connUnitEventObject OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This is used with the connUnitEventType
to identify which object the event refers to.
It can be the OID of a connectivity unit or of
another object like connUnitPortStatus[...]"
::= { connUnitEventEntry 8 }
connUnitEventDescr OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The description of the event."
::= { connUnitEventEntry 9 }
-- The link table
-- is intended to organize and communicate
-- any information the agent possesses
-- which would assist a management application
-- to discover the CONNECTIVITY UNITS in the
-- framework and the TOPOLOGY of their interconnect.
-- That is, the goal is to assist the management
-- application not only to LIST the elements of the framework,
-- but to MAP them.
-- With this goal, the agent SHOULD include
-- as much as it possesses about any links
-- from its own connectivity units to others,
-- including links among its own units.
-- An agent SHOULD include partial information
-- about links if it is not able to fully
-- define them in accord with the following structure;
-- however, the information MUST include either
-- a nonzero connUnitNodeId- or a nonzero connUnitPortWwn-
-- for each end of the link.
-- If the agent is able to discover links
-- which do not directly attach to members of its agency
-- and its discovery algorithm gives some assurance
-- the links are recently valid, it MAY include these links.
-- Link information entered by administrative action
-- MAY be included even if not validated directly
Blumenau [Page 28]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
-- if the link has at least one endpoint in this agency,
-- but SHOULD NOT be included otherwise.
-- A connectivity unit should fill the table in as best it can.
-- One of the methods to fill this in would be to use the RNID
-- ELS (ANSI document 99-422v0). This allows one to query a
-- port for the information needed for the link table.
-- This table is accessed either directly if the management
-- software has an index value or via GetNexts. The value of
-- the indexes are not required to be contiguous. Each entry
-- created in this table will be assigned an index. This
-- relationship is kept persistent until the entry is removed
-- from the table or the system is reset. The total number of
-- entries are defined by the size of the table
-- For an entry to be considered to be valid, both the X (local)
-- and the Y (remote) need to have one valid value.
connUnitLinkTable OBJECT-TYPE
SYNTAX SEQUENCE OF ConnUnitLinkEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of links know to this agent from this
connectivity unit to other connectivity units."
::= { connSet 12 }
connUnitLinkEntry OBJECT-TYPE
SYNTAX ConnUnitLinkEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry describing a particular link to another."
INDEX { connUnitLinkUnitId,
connUnitLinkIndex }
::= { connUnitLinkTable 1 }
ConnUnitLinkEntry ::=
SEQUENCE {
connUnitLinkUnitId
OCTET STRING,
connUnitLinkIndex
INTEGER,
connUnitLinkNodeIdX
OCTET STRING,
connUnitLinkPortNumberX
INTEGER,
connUnitLinkPortWwnX
OCTET STRING,
connUnitLinkNodeIdY
OCTET STRING,
connUnitLinkPortNumberY
INTEGER,
Blumenau [Page 29]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
connUnitLinkPortWwnY
OCTET STRING,
connUnitLinkAgentAddressY
OCTET STRING,
connUnitLinkAgentAddressTypeY
INTEGER,
connUnitLinkAgentPortY
INTEGER,
connUnitLinkUnitTypeY
FcUnitType,
connUnitLinkConnIdY
OCTET STRING
}
connUnitLinkUnitId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (16))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The connUnitId of the connectivity unit
that contains this link table."
::= { connUnitLinkEntry 1 }
connUnitLinkIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This value is used to create a unique value
for each entry in the link table with the same
connUnitLinkUnitId. The value
can only be reused if it is not currently in
in use and the value is the next candidate to
be used. This value is allowed to wrap at the
highest value represented by the number of bits.
This value is reset to zero when the system is
Reset and the first value to be used is one."
::= { connUnitLinkEntry 2 }
connUnitLinkNodeIdX OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(64))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The node WWN of the unit at one end
of the link. If the node WWN is unknown
and the node is a connUnit in the responding
agent then the value of this object MUST BE
equal to its connUnitID."
::= { connUnitLinkEntry 3 }
connUnitLinkPortNumberX OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
Blumenau [Page 30]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
STATUS mandatory
DESCRIPTION
"The port number on the unit specified by
connUnitLinkNodeIdX if known, otherwise -1.
If the value is nonnegative then it will be
equal to connUnitPortPhysicalNumber."
::= { connUnitLinkEntry 4 }
connUnitLinkPortWwnX OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(16))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The port WWN of the unit specified by
connUnitLinkNodeIdX if known,
otherwise 16 octets of binary 0"
::= { connUnitLinkEntry 5 }
connUnitLinkNodeIdY OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(64))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The node WWN of the unit at the other end
of the link. If the node WWN is unknown
and the node is a connUnit in the responding
SNMP agency then the value of this object
MUST BE equal to its connUnitID."
::= { connUnitLinkEntry 6 }
connUnitLinkPortNumberY OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The port number on the unit specified by
connUnitLinkNodeIdY if known, otherwise -1.
If the value is nonnegative then it will be
equal to connUnitPortPhysicalNumber."
::= { connUnitLinkEntry 7 }
connUnitLinkPortWwnY OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(16))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The port WWN on the unit specified by
connUnitLinkNodeIdY if known,
otherwise 16 octets of binary 0"
::= { connUnitLinkEntry 8 }
connUnitLinkAgentAddressY OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(16))
ACCESS read-only
Blumenau [Page 31]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
STATUS mandatory
DESCRIPTION
"The address of an FCMGMT MIB agent for the
node identified by connUnitLinkNodeIdY,
if known; otherwise 16 octets of binary 0"
::= { connUnitLinkEntry 9 }
connUnitLinkAgentAddressTypeY OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"If connUnitLinkAgentAddressY is nonzero,
it is a protocol address.
ConnUnitLinkAgentAddressTypeY is the
the 'address family number' assigned by IANA
to identify the address format.
(eg, 1 is Ipv4, 2 is Ipv6)."
::= { connUnitLinkEntry 10 }
connUnitLinkAgentPortY OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The IP port number for the agent. This is
provided in case the agent is at a non-standard
SNMP port."
::= { connUnitLinkEntry 11 }
connUnitLinkUnitTypeY OBJECT-TYPE
SYNTAX FcUnitType
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Type of the FC connectivity unit as defined in
connUnitType."
::= { connUnitLinkEntry 12 }
connUnitLinkConnIdY OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(3))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This is the Fibre Channel ID of this port.
If the connectivity unit is a switch, this
is expected to be a Big Endian value of 24
bits. If this is loop, then it is the ALPA
that is connected. If this is an eport, then
it will only contain the domain ID. If not
any of those, unknown or cascaded loop,
return all bits set to 1."
::= { connUnitLinkEntry 13 }
Blumenau [Page 32]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
------------------------------------------------------------------------------
-- The following is a set of statistics tables. There is one for each port
-- type class. Port types are aggregated into a port type class, such as all
-- the fabric port types. There is one and only one statistics table for each
-- individual port. For all objects in statistics tables, if the object is not
-- supported by the conn unit then the high order bit is set to 1 with all
-- other bits set to zero. The high order bit is reserved to indicate is the
-- object if supported or not. All objects start at a value of zero at hardware
-- initialization and continue incrementing till end of 63 bits and then wrap
-- to zero.
-- Hub Port Statistics
connUnitPortStatHubTable OBJECT-TYPE
SYNTAX SEQUENCE OF ConnUnitPortStatHubEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of statistics for the hub port type."
::= { statSet 1 }
connUnitPortStatHubEntry OBJECT-TYPE
SYNTAX ConnUnitPortStatHubEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry describing port statistics."
INDEX { connUnitPortStatHubUnitId,
connUnitPortStatHubIndex }
::= { connUnitPortStatHubTable 1 }
ConnUnitPortStatHubEntry ::=
SEQUENCE {
connUnitPortStatHubUnitId
OCTET STRING,
connUnitPortStatHubIndex
INTEGER,
connUnitPortStatHubCountError
OCTET STRING,
connUnitPortStatHubCountTxFrame
OCTET STRING,
connUnitPortStatHubCountRxFrame
OCTET STRING,
connUnitPortStatHubCountTxOctets
OCTET STRING,
connUnitPortStatHubCountRxOctets
OCTET STRING
}
connUnitPortStatHubUnitId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (16))
ACCESS read-only
STATUS mandatory
Blumenau [Page 33]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
DESCRIPTION
"The connUnitId of the connectivity unit
that contains this port stat table."
::= { connUnitPortStatHubEntry 1 }
connUnitPortStatHubIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value among all entrys
in this table, between 0 and
connUnitNumPort[connUnitPortUnitId]."
::= { connUnitPortStatHubEntry 2 }
connUnitPortStatHubCountError OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the errors that have occured
on this port."
::= { connUnitPortStatHubEntry 3 }
connUnitPortStatHubCountTxFrame OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of frames that have been transmitted
by this port."
::= { connUnitPortStatHubEntry 4 }
connUnitPortStatHubCountRxFrame OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of frames that have been received
by this port."
::= { connUnitPortStatHubEntry 5 }
connUnitPortStatHubCountTxOctets OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of octets that have been transmitted
by this port."
::= { connUnitPortStatHubEntry 6 }
connUnitPortStatHubCountRxOctets OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
ACCESS read-only
Blumenau [Page 34]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
STATUS mandatory
DESCRIPTION
"The number of octets that have been received.
by this port."
::= { connUnitPortStatHubEntry 7 }
-- Fabric Port Statistics
connUnitPortStatFabricTable OBJECT-TYPE
SYNTAX SEQUENCE OF ConnUnitPortStatFabricEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of statistics for the fabric port types."
::= { statSet 2 }
connUnitPortStatFabricEntry OBJECT-TYPE
SYNTAX ConnUnitPortStatFabricEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry describing port statistics."
INDEX { connUnitPortStatFabricUnitId,
connUnitPortStatFabricIndex }
::= { connUnitPortStatFabricTable 1 }
ConnUnitPortStatFabricEntry ::=
SEQUENCE {
connUnitPortStatFabricUnitId
OCTET STRING,
connUnitPortStatFabricIndex
INTEGER,
connUnitPortStatFabricCountError
OCTET STRING,
connUnitPortStatFabricCountTxFrame
OCTET STRING,
connUnitPortStatFabricCountRxFrame
OCTET STRING,
connUnitPortStatFabricCountTxOctets
OCTET STRING,
connUnitPortStatFabricCountRxOctets
OCTET STRING
}
connUnitPortStatFabricUnitId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (16))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The connUnitId of the connectivity unit
that contains this port stat table."
::= { connUnitPortStatFabricEntry 1 }
Blumenau [Page 35]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
connUnitPortStatFabricIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value among all entrys
in this table, between 0 and
connUnitNumPort[connUnitPortUnitId]."
::= { connUnitPortStatFabricEntry 2 }
connUnitPortStatFabricCountError OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the errors that have occured
on this port."
::= { connUnitPortStatFabricEntry 3 }
connUnitPortStatFabricCountTxFrame OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of frames that have been transmitted
by this port."
::= { connUnitPortStatFabricEntry 4 }
connUnitPortStatFabricCountRxFrame OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of frames that have been received
by this port."
::= { connUnitPortStatFabricEntry 5 }
connUnitPortStatFabricCountTxOctets OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of octets that have been transmitted
by this port."
::= { connUnitPortStatFabricEntry 6 }
connUnitPortStatFabricCountRxOctets OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of octets that have been received.
by this port."
::= { connUnitPortStatFabricEntry 7 }
Blumenau [Page 36]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
-- SCSI Port Statistics
connUnitPortStatSCSITable OBJECT-TYPE
SYNTAX SEQUENCE OF ConnUnitPortStatSCSIEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of statistics for the SCSI port type."
::= { statSet 3 }
connUnitPortStatSCSIEntry OBJECT-TYPE
SYNTAX ConnUnitPortStatSCSIEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry describing port statistics."
INDEX { connUnitPortStatSCSIUnitId,
connUnitPortStatSCSIIndex }
::= { connUnitPortStatSCSITable 1 }
ConnUnitPortStatSCSIEntry ::=
SEQUENCE {
connUnitPortStatSCSIUnitId
OCTET STRING,
connUnitPortStatSCSIIndex
INTEGER,
connUnitPortStatSCSICountError
OCTET STRING,
connUnitPortStatSCSICountTxIO
OCTET STRING,
connUnitPortStatSCSICountRxIO
OCTET STRING,
connUnitPortStatSCSICountTxBytes
OCTET STRING,
connUnitPortStatSCSICountRxBytes
OCTET STRING
}
connUnitPortStatSCSIUnitId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (16))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The connUnitId of the connectivity unit
that contains this port stat table."
::= { connUnitPortStatSCSIEntry 1 }
connUnitPortStatSCSIIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value among all entrys
in this table, between 0 and
Blumenau [Page 37]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
connUnitNumPort[connUnitPortUnitId]."
::= { connUnitPortStatSCSIEntry 2 }
connUnitPortStatSCSICountError OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A count of the errors that have occured
on this port."
::= { connUnitPortStatSCSIEntry 3 }
connUnitPortStatSCSICountTxIO OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of I/Os that have been transmitted
by this port."
::= { connUnitPortStatSCSIEntry 4 }
connUnitPortStatSCSICountRxIO OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of I/Os that have been received
by this port."
::= { connUnitPortStatSCSIEntry 5 }
connUnitPortStatSCSICountTxBytes OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of bytes that have been transmitted
by this port."
::= { connUnitPortStatSCSIEntry 6 }
connUnitPortStatSCSICountRxBytes OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of bytes that have been received.
by this port."
::= { connUnitPortStatSCSIEntry 7 }
-- LAN/WAN Port Statistics
connUnitPortStatLANTable OBJECT-TYPE
SYNTAX SEQUENCE OF ConnUnitPortStatLANEntry
ACCESS not-accessible
STATUS mandatory
Blumenau [Page 38]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
DESCRIPTION
"A list of statistics for the LAN/WAN port type."
::= { statSet 4 }
connUnitPortStatLANEntry OBJECT-TYPE
SYNTAX ConnUnitPortStatLANEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry describing port statistics."
INDEX { connUnitPortStatLANUnitId,
connUnitPortStatLANIndex }
::= { connUnitPortStatLANTable 1 }
ConnUnitPortStatLANEntry ::=
SEQUENCE {
connUnitPortStatLANUnitId
OCTET STRING,
connUnitPortStatLANIndex
INTEGER,
connUnitPortStatLANCountError
OCTET STRING,
connUnitPortStatLANCountTxPacket
OCTET STRING,
connUnitPortStatLANCountRxPacket
OCTET STRING,
connUnitPortStatLANCountTxBytes
OCTET STRING,
connUnitPortStatLANCountRxBytes
OCTET STRING
}
connUnitPortStatLANUnitId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (16))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The connUnitId of the connectivity unit
that contains this port stat table."
::= { connUnitPortStatLANEntry 1 }
connUnitPortStatLANIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A unique value among all entrys
in this table, between 0 and
connUnitNumPort[connUnitPortUnitId]."
::= { connUnitPortStatLANEntry 2 }
connUnitPortStatLANCountError OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
ACCESS read-only
Blumenau [Page 39]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
STATUS mandatory
DESCRIPTION
"A count of the errors that have occured
on this port."
::= { connUnitPortStatLANEntry 3 }
connUnitPortStatLANCountTxPacket OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of packets that have been transmitted
by this port."
::= { connUnitPortStatLANEntry 4 }
connUnitPortStatLANCountRxPacket OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of packets that have been received
by this port."
::= { connUnitPortStatLANEntry 5 }
connUnitPortStatLANCountTxBytes OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of bytes that have been transmitted
by this port."
::= { connUnitPortStatLANEntry 6 }
connUnitPortStatLANCountRxBytes OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of bytes that have been received.
by this port."
::= { connUnitPortStatLANEntry 7 }
-----------------------------------------------------------------------
-- SNMP trap registration group
trapMaxClients OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The maximum number of SNMP trap recipients
supported by the connectivity unit."
::= { trapReg 1 }
Blumenau [Page 40]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
trapClientCount OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The current number of rows in the trap table."
::= { trapReg 2 }
trapRegTable OBJECT-TYPE
SYNTAX SEQUENCE OF TrapRegEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A table containing a row for each IP address/port
number that traps will be sent to."
::= { trapReg 3 }
trapRegEntry OBJECT-TYPE
SYNTAX TrapRegEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Ip/Port pair for a specific client."
INDEX { trapRegIpAddress,
trapRegPort }
::= { trapRegTable 1 }
TrapRegEntry ::=
SEQUENCE {
trapRegIpAddress
IpAddress,
trapRegPort
INTEGER (1..2147483647),
trapRegFilter
FcEventSeverity,
trapRegRowState
INTEGER
}
trapRegIpAddress OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The Ip address of a client registered for
traps."
::= { trapRegEntry 1 }
trapRegPort OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The UDP port to send traps to for this host.
Blumenau [Page 41]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
Normally this would be the standard trap port
(162). This object is an index and must be
specified to create a row in this table."
::= { trapRegEntry 2 }
trapRegFilter OBJECT-TYPE
SYNTAX FcEventSeverity
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value defines the trap severity
filter for this trap host. The connUnit will send
traps to this host that have a severity level
less than or equal to this value.
The default value of this object is 'warning'."
::= { trapRegEntry 3}
trapRegRowState OBJECT-TYPE
SYNTAX INTEGER {
rowDestroy(1), -- Remove row from table.
rowInactive(2), -- Row exists, but TRAPs disabled
rowActive(3) -- Row exists and is enabled for
-- sending traps
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Specifies the state of the row.
rowDestroy
READ: Can never happen.
WRITE: Remove this row from the table.
rowInactive
READ: Indicates that this row does exist, but
that traps are not enabled to be sent to the
target.
WRITE: If the row does not exist, and the agent
allows writes to the trap table, then a new
row is created. The values of the optional
columns will be set to default values. Traps are
not enabled to be sent to the target. If the row
already existed, then traps are disabled from being
sent to the target.
rowActive
READ: Indicates that this row exists, and that traps
are enabled to be sent to the target.
WRITE: If the row does not exist, and the agent
allows writes to the trap table, then a new row is
created. The values of the optional columns will be
set to default values. Traps are enabled to be sent
to the target. If the row already exists, then traps
are enabled to be sent to the target.
A value of rowActive or rowInactive must be specified to
create a row in the table."
::= { trapRegEntry 4}
Blumenau [Page 42]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
-- Related traps
connUnitStatusChange TRAP-TYPE
ENTERPRISE fcmgmt
VARIABLES { connUnitStatus, connUnitState }
DESCRIPTION
"The overall status of the connectivity unit has
changed.
Recommended severity level (for filtering): alert"
::= 1
-- connUnitAddedTrap , 2, no longer used
connUnitDeletedTrap TRAP-TYPE
ENTERPRISE fcmgmt
VARIABLES { connUnitId }
DESCRIPTION
"A connUnit has been deleted from this agent.
Recommended severity level (for filtering): warning"
::= 3
connUnitEventTrap TRAP-TYPE
ENTERPRISE fcmgmt
VARIABLES { connUnitEventId,
connUnitEventType,
connUnitEventObject,
connUnitEventDescr }
DESCRIPTION
"An event has been generated by the
connectivity unit.
Recommended severity level (for filtering): info"
::= 4
connUnitSensorStatusChange TRAP-TYPE
ENTERPRISE fcmgmt
VARIABLES { connUnitSensorStatus }
DESCRIPTION
"The overall status of the connectivity unit has
changed.
Recommended severity level (for filtering): alert"
::= 5
connUnitPortStatusChange TRAP-TYPE
ENTERPRISE fcmgmt
VARIABLES { connUnitPortStatus, connUnitPortState }
DESCRIPTION
"The overall status of the connectivity unit has
changed.
Recommended severity level (for filtering): alert"
::= 6
END
Blumenau [Page 43]
INTERNET-DRAFT FC Mgmt Integration MIB Dec 28, 1999
Author Contact Information:
Steven Blumenau
EMC Corporation
171 South Street
Hopkinton, MA 01748-9103
USA
Phone: 1-508-435-1000 x4657
E-mail: blumenau_steven@isus.emc.com
(This draft expires June 28, 2000.)
Blumenau [Page 44]
| PAFTECH AB 2003-2026 | 2026-04-21 03:47:11 |