One document matched: draft-ietf-avt-topologies-04.txt
Differences from draft-ietf-avt-topologies-03.txt
Network Working Group Magnus Westerlund
INTERNET-DRAFT Ericsson
Expires: Aug 2007 Stephan Wenger
Intended Status: Informational Nokia
February 22, 2007
RTP Topologies
<draft-ietf-avt-topologies-04.txt>
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other
documents at any time. It is inappropriate to use Internet-Drafts
as reference material or to cite them other than as "work in
progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Copyright Notice
Copyright (C) The IETF Trust (2007).
Abstract
This document discucsses multi-endpoint topologies used in RTP
based environments. In particular, centralized topologies commonly
employed in the video conferencing industry are mapped to the RTP
terminology.
Wenger, et al. [Page 1]
INTERNET-DRAFT RTP Topologies February 22, 2007
TABLE OF CONTENTS
Status of this Memo................................................1
Copyright Notice...................................................1
Abstract...........................................................1
TABLE OF CONTENTS..................................................2
1. Introduction....................................................3
2. Definitions.....................................................3
2.1. Glossary....................................................3
2.2. Indicating Requirement leves................................3
3. Topologies......................................................4
3.1. Point to Point..............................................4
3.2. Point to Multi-point using Multicast........................5
3.3. Point to Multipoint using the RFC 3550 translator...........6
3.4. Point to Multipoint using the RFC 3550 mixer model..........9
3.5. Point to Multipoint using video switching MCU..............11
3.6. Point to Multipoint using RTCP-terminating MCU.............12
3.7. Combining Topologies.......................................13
4. Comparing Topologies...........................................14
4.1. Topology Proporties........................................14
4.1.1. All to All media transmission.........................14
4.1.2. Transport or Media Interoperability...................14
4.1.3. Per Domain Bit-rate Adaptation........................15
4.1.4. Aggregation of Media..................................15
4.1.5. View of all session participants......................15
4.1.6. Loop Detection........................................16
4.2. Comparision of topologies..................................16
5. Security Considerations........................................16
6. Acknowledgements...............................................18
7. IANA Considerations............................................18
8. References.....................................................19
8.1. Normative References.......................................19
8.2. Informative References.....................................19
9. Authors' Addresses.............................................19
RFC Editor Considerations.........................................20
Wenger, et al. Informational [Page 2]
INTERNET-DRAFT RTP Topologies February 22, 2007
1. Introduction
When working on the Codec Control Messages [CCM], a considerable
confusion was noticed in the community, with respect to terms such
as MCU, mixer, and translator, and their usage in various
topologies. This document tries to address this confusion by
providing a common information basis for future discussion and
specification work. It attempts to clarify and explain sections of
the RTP spec [RFC3550] in an informal way. It is not intended to
update or change what is normatively specified within RFC 3550.
When the Audio-Visual Profile with Feedback (AVPF) [RFC4585] was
developed, the main emphasis lay in the efficient support of point-
to-point and small multipoint scenarios without centralized
multipoint control. However, in practice, many small multipoint
conferences operate utilizing devices known as Multipoint Control
Units (MCUs). MCUs may implement mixers and translators (in RTP
[RFC3550] terminology), but also signalling support. They may also
contain additional application functionality. This document
focuses on the media transport aspects of the MCU that can be
realized using RTP, as discussed below. Further considered are the
properties of mixers and translators, and how some types of
deployed MCUs deviate from these properties.
2. Definitions
2.1. Glossary
ASM - Asynchronous Multicast
AVPF - The Extended RTP Profile for RTCP-based Feedback
CSRC - Contributing Source
Link - The data transport to the next IP hop
MCU - Multipoint Control Unit
Path - The concatenation of multiple links, resulting in a end-
to-end data transfer.
PtM - Point to Multipoint
PtP - Point to Point
SSRC - Synchronization Source
2.2. Indicating Requirement leves
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL
NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
Wenger, et al. Informational [Page 3]
INTERNET-DRAFT RTP Topologies February 22, 2007
RFC 2119 [RFC2119].
The RFC 2119 language is used in this document to highlight those
important requirements and/or resulting solutions that are
necessary to address the issues raised in this document.
3. Topologies
This subsection defines several basic topologies that are relevant
for codec control. The first four relate to the RTP system model
utilizing multicast and/or unicast, as envisioned in RFC 3550. The
last two topologies, in contrast, describe the deployed system
models as used in many H.323 [H323] video conferences, where both
the media streams and the RTCP control traffic terminate at the
MCU. More topologies can be constructed by combining any of the
models; see Section 3.7.
The topologies may be referenced in other documents by a shortcut
name, indicated by the prefix "Topo-".
For each of the RTP defined topologies, we discuss how RTP, RTCP,
and the carried media are handled. With respect to RTCP, we also
introduce the handling of RTCP feedback message as defined in
[RFC4585] and [CCM]. Any important differences between the two will
be illuminated in the discussion.
3.1. Point to Point
Shortcut name: Topo-Point-to-Point
The Point to Point (PtP) topology (Figure 1) consists of two end-
points, communicating using unicast. Both RTP and RTCP traffic are
conveyed endpoint-to-endpoint, using unicast traffic only (even if-
--in exotic cases---this unicast traffic happens to be conveyed
over an IP-multicast address).
+---+ +---+
| A |<------->| B |
+---+ +---+
Figure 1 - Point to Point
The main property of this topology is that A sends to B and only B,
while B sends to A and only A. This avoids all complexities of
handling multiple endpoints and combining the requirements from
them. Do note that an endpoint can still use multiple RTP
Synchronization Sources (SSRCs) in an RTP session.
Wenger, et al. Informational [Page 4]
INTERNET-DRAFT RTP Topologies February 22, 2007
RTCP feedback messages for the indicated SSRCs are communicated
directly between the endpoints. Therefore, this topology poses
minimal (if any) issues for any feedback messages.
3.2. Point to Multi-point using Multicast
Shortcut name: Topo-Multicast
+-----+
+---+ / \ +---+
| A |----/ \---| B |
+---+ / Multi- \ +---+
+ Cast +
+---+ \ Network / +---+
| C |----\ /---| D |
+---+ \ / +---+
+-----+
Figure 2 - Point to Multipoint using Multicast
Point to Multipoint (PtM) is defined here as using a multicast
topology as a transmission model, in which traffic from any
participant reaches all the other participants, except for cases
such as
o packet loss, or
o a participant does not wish to receive the traffic for a
specific multicast group, and therefore has not subscribed to
the IP multicast group in question. This is for the cases
where a multi-media session is distributed using two or more
multicast groups.
In the above context, "traffic" encompasses both RTP and RTCP
traffic. The number of participants can vary between one and many-
--as RTP and RTCP scales to very large multicast groups (the
theoretical limit of the number of participants in a single RTP
session is approximately two billion).
This draft is primarily interested in that subset of multicast
sessions wherein the number of participants in the multicast group
is so low that it allows the participants to use early or immediate
feedback, as defined in AVPF [RFC4585]. This document refers to
those groups as "small multicast groups".
RTCP feedback messages in multicast will, like media, reach
everyone (subject to packet losses and multicast group
subscription). Therefore, the feedback suppression mechanism
discussed in [RFC4585] is required. Each individual node needs to
Wenger, et al. Informational [Page 5]
INTERNET-DRAFT RTP Topologies February 22, 2007
process every feedback message it receives, to determine if it is
affected, or if the feedback message applies only to some other
participant.
3.3. Point to Multipoint using the RFC 3550 translator
Shortcut name: Topo-Translator
Two main categories of Translators can be distinguished.
Transport Translators do not modify the media stream itself, but
are concerned with transport parameters. Transport parameters, in
the sense of this section, comprise the transport addresses (to
bridge different domains), and the media packetization to allow
other transport protocols to be interconnected to a session (in
gateways). Of the transport translators, this memo is primarily
interested in those which use RTP on both sides, and this is
assumed henceforth. Translators that bridge between different
protocol worlds need to be concerned about the mapping of the
SSRC/CSRC concept to the non-RTP protocol. When designing a
translator to a non-RTP based media transport, one crucial factor
consists in how to handle different sources and their identity.
This problem space is not discussed henceforth.
Media Translators, in contrast, modify the media stream itself.
This process is commonly known as transcoding. The modification of
the media stream can be as small as removing parts of the stream,
and can go all the way to a full transcoding (down to the sample
level or equivalent) utilizing a different media codec. Media
translators are commonly used to connect entities without a common
interoperability point.
Stand-alone Media Translators are rare. Most commonly, a
combination of Transport and Media Translators are used to
translate both the media stream and the transport aspects of a
stream between two transport domains (or clouds).
Both Translator types share common attributes that separate them
from mixers. For each media stream that the translator receives,
it generates an individual stream in the other domain. In
addition, a translator maintains a complete view of all existing
participants between both domains. Therefore, the SSRC space is
shared across the two domains.
The RTCP translation process can be trivial---for example when
Transport translators just need to adjust IP addresses---and can be
quite complex in the case of media translators. See section 7.2 of
[RFC3550].
Wenger, et al. Informational [Page 6]
INTERNET-DRAFT RTP Topologies February 22, 2007
+-----+
+---+ / \ +------------+ +---+
| A |<---/ \ | |<---->| B |
+---+ / Multi- \ | | +---+
+ Cast +->| Translator |
+---+ \ Network / | | +---+
| C |<---\ / | |<---->| D |
+---+ \ / +------------+ +---+
+-----+
Figure 3 - Point to Multipoint using a Translator
Figure 3 depicts an example of a Transport Translator performing at
least IP address translation. It allows the (non multicast-
capable) participants B and D to take part in a multicast session
by having the translator forward their unicast traffic to the
multicast addresses in use, and vice versa. It must also forward
B's traffic to D and vice versa, to provide each of B and D with a
complete view of the session.
If B were behind a limited network path, the translator may perform
media transcoding to allow the traffic received from the other
participants to reach B without overloading the path.
When, in the example depicted in Figure 3, the translator acts only
as a Transport Translator, then the RTCP traffic can simply be
forwarded, similar to the media traffic. However, when media
translation occurs, the translator's task becomes substantially
more complex, even with respect to the RTCP traffic. In this case,
the translator needs to rewrite B's RTCP receiver report, before
forwarding them to D and the multicast network. The rewriting is
needed as the stream received by B is not the same stream as the
other participants receive. For example, the number of packets
transmitted to B may be lower than what D receives, due to the
different media format. Therefore, if the receiver reports were
forwarded without changes, the extended highest sequence number
would indicate that B were substantially behind in reception---
while it most likely it would not be. Therefore, the translator
must translate that number to a corresponding sequence number for
the stream the translator received. Similar arguments can be made
for most other fields in the RTCP receiver reports.
As specified in Section 7.1 of [RFC3550], the SSRC space is common
for all participants in the session, independent of which side they
are of the translator. Therefore, it is the responsibility of the
participants to run SSRC collision detection, and the SSRC is a
field the translator should not change.
Wenger, et al. Informational [Page 7]
INTERNET-DRAFT RTP Topologies February 22, 2007
+---+ +------------+ +---+
| A |<---->| |<---->| B |
+---+ | | +---+
| Translator |
+---+ | | +---+
| C |<---->| |<---->| D |
+---+ +------------+ +---+
Figure 4 - RTP Translator (relay) with only unicast paths
Another translator scenario is depicted in Figure 4. Herein, the
translator connects multiple users of a conference through unicast.
This can be implemented using a very simple transport translator,
which in this document is called a relay. The relay forwards all
traffic it receives, both RTP and RTCP, to all other participants.
In doing so, a multicast network is emulated without relying on a
multicast capable network infrastructure.
A translator normally does not use an SSRC of its own, and is not
visible as an active participant in the session. One exception can
be conceived when it acts as a quality monitor that sends RTCP
reports, and therefore is required to have an SSRC. Another
example is the case when a translator is prepared to use RTCP
feedback messages. This may, for example, occur when it suffers
packet loss of important video packets and wants to trigger repair
by the media sender, by sending feedback messages. To be able to
do this it needs to have a unique SSRC.
A media translator may in some cases act on behalf of the ``real''
source and respond to RTCP feedback messages. This may occur, for
example, when a receiver requests a bandwidth reduction, and the
media translator has not detected any congestion or other reasons
for bandwidth reduction between the media source and itself. In
that case, it is sensible that the media translator reacts to the
codec control messages itself, for example by transrating through a
transcoding step. If it were not reacting, the media quality in
the media sender's domain may suffer, as a result of the media
sender adjusting its media rate (and quality) according to the
needs of the slow past-translator endpoint, at the expense of the
rate and quality of all other session participants.
In general, a translator implementation should consider which RTCP
feedback messages or codec control messages it needs to understand
in relation to the functionality of the translator itself. This is
completely in line with the requirement to translate also RTCP
messages between the domains.
Wenger, et al. Informational [Page 8]
INTERNET-DRAFT RTP Topologies February 22, 2007
3.4. Point to Multipoint using the RFC 3550 mixer model
Shortcut name: Topo-Mixer
A mixer is a middlebox that aggregates multiple RTP streams that
are part of a session, by mixing the media data and generating a
new RTP stream. One common application for a mixer is to allow a
participant to receive a session with a reduced amount of
resources.
+-----+
+---+ / \ +-----------+ +---+
| A |<---/ \ | |<---->| B |
+---+ / Multi- \ | | +---+
+ Cast +->| Mixer |
+---+ \ Network / | | +---+
| C |<---\ / | |<---->| D |
+---+ \ / +-----------+ +---+
+-----+
Figure 5 - Point to Multipoint using RFC 3550 mixer model
A mixer can be viewed as a device terminating the media streams
received from other session participants. Using the media data
from the received media streams, a mixer generates a media stream
that is sent to the session participant.
The content that the mixer provides is the mixed aggregate of what
the mixer receives over the PtP or PtM paths, which are part of the
same conference session.
The mixer is the content source, as it mixes the content (often in
the uncompressed domain) and then encodes it for transmission to a
participant. The CC and CSRC fields in the RTP header are used to
indicate the contributors of to the newly generated stream. The
SSRCs of the to-be-mixed streams on the mixer input appear as the
CSRCs at the mixer output. That output stream uses a unique SSRC
that identifies the Mixer's stream. The CSRC are forwarded between
the two domains to allow for loop detection and identification of
sources that are part of the global session. Note that Section 7.1
of RFC 3550 requires the SSRC space to be shared between domains
for these reasons.
The mixer is responsible for generating RTCP packets in accordance
with its role. It is a receiver and should therefore send reception
reports for the media streams it receives. In its role as a media
sender, it should also generate sender report for those media
streams sent. The content of the SRs created by the mixer may or
may not take into account the situation on its receiving side.
Wenger, et al. Informational [Page 9]
INTERNET-DRAFT RTP Topologies February 22, 2007
Similarly, the content of RRs created by the mixer may or may not
be based on the situation on the mixer's sending side. This is
left open to the implementation. As specified in Section 7.3 of
RFC 3550, a mixer must not forward RTCP unaltered between the two
domains.
The mixer depicted in Figure 5 is involved in three domains that
need to be separated; the multicast network, participant B and
participant D. The Mixer produces different mixed streams to B and
D, as the one to B may contain content received from D and vice
versa. However, the mixer does only need one SSRC in each domain
that is the receiving entity and transmitter of mixed content.
In the multicast domain, the mixer does not need to provide a mixed
view of the other domains and will commonly only forward the media
from B and D into the multicast network using B's and D's SSRC.
A mixer is responsible for receiving RTCP feedback messages and
handling them appropriately. The definition of "appropriate"
depends on the message itself and the context. In some cases, the
reception of a codec control message may result in the generation
and transmission of RTCP feedback messages by the mixer to the
participants in the other domain. In other cases, a message is
handled by the mixer itself and therefore not forwarded to any
other domain.
When replacing the multicast network in Figure 5 (to the left of
the mixer) with individual unicast paths as depicted in Figure 6,
the mixer model is very similar to the one discussed in section 3.6
below. Please see the discussion in 3.6 about the differences
between these two models.
+---+ +------------+ +---+
| A |<---->| |<---->| B |
+---+ | | +---+
| Mixer |
+---+ | | +---+
| C |<---->| |<---->| D |
+---+ +------------+ +---+
Figure 6 - RTP Mixer with only unicast paths
Wenger, et al. Informational [Page 10]
INTERNET-DRAFT RTP Topologies February 22, 2007
3.5. Point to Multipoint using video switching MCU
Shortcut name: Topo-Video-switch-MCU
+---+ +------------+ +---+
| A |------| Multipoint |------| B |
+---+ | Control | +---+
| Unit |
+---+ | (MCU) | +---+
| C |------| |------| D |
+---+ +------------+ +---+
Figure 7 - Point to Multipoint using relaying MCU
This PtM topology is still deployed today, although the RTCP-
terminating MCUs, as discussed in the next section, are perhaps
more common. This topology, as well as the following one, reflect
today's lack of wide availability of IP multicast technologies, as
well as the simplicity of content switching when compared to
content mixing. The technology is commonly implemented in what is
known as "Video Switching MCUs".
A video switching MCU forwards to a participant a single media
stream, selected from the available streams. The criteria for
selection are often based on voice activity in the audio-visual
conference, but other conference management mechanisms (like
presentation mode or explicit floor control) are known to exist as
well.
The video switching MCU may also perform media translation, to
modify the content in bit-rate, encoding, or resolution; however it
still may indicate the original sender of the content through the
SSRC. In this case the values of the CC and CSRC fields are
retained.
If not terminating RTP, the RTCP Sender Reports are forwarded for
the currently selected sender. All RTCP receiver reports are freely
forwarded between the participants. In addition, the MCU may also
originate RTCP control traffic in order to control the session
and/or report on status from its viewpoint.
The video switching MCU has mostly the attributes of a translator.
However, its stream selection is a mixing behavior. This behavior
has some RTP and RTCP issues associated with it. The suppression
of all but one media stream results in most participants seeing
only a subset of the sent media streams at any given time; often a
single stream per conference. Therefore, RTCP receiver reports
only report on these streams. Consequently, the media senders that
are not currently forwarded receive a view of the session that
Wenger, et al. Informational [Page 11]
INTERNET-DRAFT RTP Topologies February 22, 2007
indicates their media streams disappear somewhere en route. This
makes the use of RTCP for congestion control or any type of quality
reporting very problematic.
To avoid the aforementioned issues, the MCU needs to implement two
aspects. First it needs to act as a mixer (see section 3.4) and
forward the selected media stream under its own SSRC and with the
appropriate CSRC values. The second is to modify the RTCP RRs it
forwards between the domains. As a result, it is RECOMMENDED that
one implements a centralized video switching conference using a
Mixer according to RFC 3550, instead of the shortcut implementation
described here.
3.6. Point to Multipoint using RTCP-terminating MCU
Shortcut name: Topo-RTCP-terminating-MCU
+---+ +------------+ +---+
| A |<---->| Multipoint |<---->| B |
+---+ | Control | +---+
| Unit |
+---+ | (MCU) | +---+
| C |<---->| |<---->| D |
+---+ +------------+ +---+
Figure 8 - Point to Multipoint using content modifying MCU
In this PtM scenario, each participant runs an RTP point-to-point
session between itself and the MCU. This is a very commonly
deployed topology in multipoint video conferencing. The content
that the MCU provides to each participant is either:
a) A selection of the content received from the other
participants, or
b) The mixed aggregate of what the MCU receives from the other
PtP paths, which are part of the same conference session.
In case a) the MCU may modify the content in bit-rate, encoding, or
resolution. No explicit RTP mechanism is used to establish the
relationship between the original media sender and the version the
MCU sends. In other words, the outgoing sessions typically uses a
different SSRC, and may well use a different payload type (PT),
even if this different PT happens to be mapped to the same media
type. This is a result of the session to each participant is
negotiated individually.
Wenger, et al. Informational [Page 12]
INTERNET-DRAFT RTP Topologies February 22, 2007
In case b) the MCU is the content source as it mixes the content
and then encodes it for transmission to a participant. According to
RTP [RFC3550], the SSRC of the contributors are to be signalled
using the CSRC/CC mechanism. In practice, today, most deployed
MCUs do not implement this feature. Instead, the identification of
the participants whose content is included in the mixer's output is
not indicated through any explicit RTP mechanism. That is, most
deployed MCUs set the CSRC Count (CC) field in the RTP header to
zero, thereby indicating no available CSRC information, even if
they could identify the content sources as suggested in RTP.
The main feature that sets this topology apart from what RFC 3550
describes is the breaking of the common RTP session across the
centralized device, such as the MCU. This results in the loss of
explicit RTP level indication of all participants. If one were
using the mechanisms available in RTP and RTCP to signal this
explicitly, the topology would follow the approach of an RTP mixer.
The lack of explicit indication has at least the following
potential problems:
1) Loop detection cannot be performed on the RTP level. When
carelessly connecting two misconfigured MCUs, a loop could be
generated.
2) There is no information about active media senders available
in the RTP packet. As this information is missing, receivers
cannot use it. It also deprives the client of information
related to currently active senders in a machine-usable way,
thus preventing clients from indicating currently active
speakers in user interfaces, etc.
Note, that deployed MCUs (and endpoints) rely on signalling layer
mechanisms for the identification of the contributing sources; for
example a SIP conferencing package [RFC4575]. This alleviates to
some extent the aforementioned issues resulting from ignoring RTP's
CSRC mechanism.
As a result of the shortcomings of this topology it is RECOMMENDED
to instead implement the Mixer concept as specified by RFC 3550.
3.7. Combining Topologies
Topologies can be combined and linked to each other using mixers or
translators. However, care must be taken in handling the SSRC
space. Mixers separate the SSRC space into two parts, while
translators maintain the space across themselves. The combined SSRC
and CSRC space still needs to be be common over any translator or
mixer. Any hybrid, like the Topo-Video-switch-MCU, requires
considerable thought on how RTCP is dealt with. Do note that the
Wenger, et al. Informational [Page 13]
INTERNET-DRAFT RTP Topologies February 22, 2007
SSRC uniqueness always needs to be global across the different
domains.
4. Comparing Topologies
The topologies discussed in section 3 have different properties.
This section first lists these properties and then maps the
different topologies to them. Please note that even if a certain
property is supported within a particular topology concept, the
necessary functionality may in many cases be optional to implement.
4.1. Topology Proporties
4.1.1. All to All media transmission
Multicast, at least Any Source Multicast (ASM), provides the
functionality that everyone may send to, or receive from, everyone
else within the session. MCUs, Mixers and Translators may all
provide that functionality at least on some basic level. However
there are some differences in what type of reachability they
provide.
The transport translator function called "relay" in Section 3.3 is
the one that provides the emulation of ASM that is closest to true
IP-multicast-based all-to-all transmission. Media Translators,
Mixers and the MCU variants do not provide a fully meshed
forwarding on the transport level, instead they only allow limited
forwarding of content from the other session participants.
The "all to all media transmission" requires that any media
transmitting entity considers the path to the least capable
receiver. Otherwise the media transmissions may overload that path.
Therefore, a media sender needs to monitor the path from itself to
any of the participants, to detect the least capable receiver at
this time instance, and adapt its sending rate accordingly. As
multiple participants may send simultaneously, the available
resources may vary. RTCP's Receiver Report help performing this
monitoring, at least on a medium time scale.
The transmission of RTCP automatically adapts to any changes in the
number of participants due to the transmission algorithm defined in
the RTP specification [RFC3550], and the extensions in AVPF
[RFC4585] (when applicable). That way, the resources utilized for
RTCP stay within the bounds configured for the session.
4.1.2. Transport or Media Interoperability
Wenger, et al. Informational [Page 14]
INTERNET-DRAFT RTP Topologies February 22, 2007
Translators, Mixers and RTCP terminating MCU all allow changing the
media encoding or the transport to other properties of the other
domain, thereby providing extended interoperability in cases where
the participants lack a common set of media codecs and/or transport
protocols.
4.1.3. Per Domain Bit-rate Adaptation
Participants are most likely to be connected to each other with a
heterogenous set of paths. This makes congestion control in a point
to multi-point set problematic. For the ASM and "relay" scenario,
each individual sender has to adapt to the receiver with the least
capable path. This is no longer necessary when Media Translators,
Mixers or MCUs are involved, as each participant only needs to
adapt to the slowest path within its own domain. The Translator,
Mixer or MCU topologies all require their respective outgoing
streams to adjust the bit-rate, packet rate, etc, to adapt to the
least capable path in each of the other domains. That way one can
avoid lowering the quality to least capable participant in all the
domains, at the cost (complexity, delay, equipment) of the Mixer or
Translator.
4.1.4. Aggregation of Media
In the all-to-all-media property mentioned above and provided by
ASM, all simultaneous media transmissions share the available bit-
rate. For participants with limited reception capabilities this may
result in that not even a minimal acceptable media quality is
accomplished. This is the result of multiple media streams need to
share the available resources. The solution to this problem is to
provide for a mixer or MCU to aggregate the multiple streams into a
single one. This aggregation can be performed according to
different methods. Mixing or selection are two common methods.
4.1.5. View of all session participants
The RTP protocol includes functionality to identify the session
participants through the use of the SSRC and CSRC fields. In
addition, it is capable of carrying some further identity
information about these participants using the RTCP Session
Descriptors (SDES). To maintain this functionality, it is necessary
that RTCP is handled correctly in domain bridging function. This is
specified for translators and mixers. The MCUs described in Section
3.5 does not fully fulfill this. The one described in Section 3.6
does not support this at all.
Wenger, et al. Informational [Page 15]
INTERNET-DRAFT RTP Topologies February 22, 2007
4.1.6. Loop Detection
In complex topologies with multiple domains interconnected, it is
possible to form media loops. RTP and RTCP support detecting such
loops, as long as the SSRC and CSRS identities are correctly set in
forwarded packets. It is likely that loop detection works for the
MCU described in Section 3.5, at least as long as it forwards the
RTCP between the participants. However, the MCU in section 3.6 will
definitely break the loop detection mechanism.
4.2. Comparision of topologies
The below table attempts to summarize the properties the different
topologies have. The legend to the topology abbrevations are:
Unicast (Unic), Multicast (Multic), Transport Translator (TTrn),
Media Translator (MTrn), Mixer (Mixer), Video switching MCU (MCUs),
and RTCP terminating MCU (MCUt).
Property Unic Multic TTrn MTrn Mixer MCUs MCUt
------------------------------------------------------------------
All to All media N Y Y Y (Y) (Y) (Y)
Interoperability N/A N Y Y Y N Y
Per Domain Adaptation N/A N N Y Y N Y
Aggregation of media N N N N Y Y Y
Full Session View Y Y Y Y Y (Y) N
Loop Detection Y Y Y Y Y (Y) N
Please note that the Media Translator also includes the transport
translator functionality.
5. Security Considerations
The use of mixers and translators has impact on security and the
security functions used. The primary issue is that both mixers and
translators modify packets, thus preventing the use of integrity
and source authentication, unless they are trusted devices that
take part in the security context, e.g. the device can send SRTP
and SRTCP [RFC3711] packets to session endpoints. If encryption is
employed, the media translator and mixer needs to be able to
decrypt the media to perform its function. A transport translator
may be used without access to the encrypted payload in cases where
it translates parts that are not included in the encryption and
integrity protection, for example, IP address and UDP port numbers
in a media stream using SRTP [RFC3711]. However, in general the
translator or mixer needs to be part of the signalling context and
get the necessary security associations (e.g. SRTP crypto contexts)
established with its RTP session participants.
Wenger, et al. Informational [Page 16]
INTERNET-DRAFT RTP Topologies February 22, 2007
Including the mixer and translator in the security context allows
the entity, if subverted or misbehaving, to perform a number of
very serious attacks as it has full access. It can perform all the
attacks possible---see RFC 3550 and any applicable profiles---as if
the media session were not protected at all, while giving the
impression to the session participants that they are protected.
Transport translators have no interactions with cryptography that
works above the transport layer, such as SRTP, since that sort of
translator leaves the RTP header and payload unaltered. Media
translators, on the other hand, have strong interactions with
cryptography, since they alter the RTP payload. A media translator
in a session that uses cryptographic protection needs to perform
cryptographic processing to both inbound and outbound packets.
A media translator may need to use different cryptographic keys for
the inbound and outbound processing. For SRTP, different keys are
required, because an RFC 3550 media translator leaves the SSRC
unchanged during its packet processing, and SRTP key sharing is
only allowed when distinct SSRCs can be used to protect distinct
packet streams.
When the media translator uses different keys to process inbound
and outbound packets, each session participant needs to be provided
with the appropriate key, depending on whether they are listening
to the translator or the original source. (Note that there is an
architectural difference between RTP media translation, in which
participants can rely on the RTP Payload Type field of a packet to
determine appropriate processing, and cryptographically protected
media translation, in which participants must use information that
is not carried in the packet.)
When using security mechanisms with translators and mixers, it is
possible that the translator or mixer creates different security
associations for the different domains they are working in. Doing
so has some implications.
First, it might weaken security if the mixer/translator accepts in
one domain a weaker algorithm or key than in another. Therefore,
care should be taken that appropriatly strong security parameters
are negotiated in all domains. In many cases, "appropriate"
translates to "similar" strength. If a key management system does
allow the negotiation of security parameters resulting in a
different strength of the security, then this system SHOULD notify
the participants in the other domains about this.
Second, the number of crypto contexts (keys, security related
state) needed (for example in SRTP [RFC3711]) may vary between
mixers and translators. A mixer normally needs to represent only a
Wenger, et al. Informational [Page 17]
INTERNET-DRAFT RTP Topologies February 22, 2007
single SSRC per domain, and therefore needs to create only one
security association (SRTP crypto context) per domain. In
contrast, a translator needs one security association per
participant it translates towards, in the opposite domain.
Considering Figure 3, the translator needs two security
associations towards the multicast domain, one for B and one for D.
It may be forced to maintain a set of totally independent security
associations between itself and B and D respectively, so to avoid
two-time pad. These contexts must also be capable of handling all
the sources present in the other domains. Hence, using completely
independent security associations (for certain keying mechanisms)
may force a translator to handle N*D keys and related state;
wherein N is the total of number of SSRCs part of the joint SSRC
space over all domains, and D is the total number of domains.
There exist a number of different mechanisms to provide keys to the
different participants. One example is the choice between group
keys and unique keys per SSRC. The appropriate keying model is
impacted by the topologies one intends to use. The final security
properties are dependent on both the topologies in use and the
keying mechanisms' properties, and need to be considered by the
application. Exactly what mechanisms are used is outside of the
scope of this document.
6. Acknowledgements
The authors would like to thank Bo Burman, Umesh Chandra, Roni
Even, Keith Lantz, Ladan Gharai and Mark Baugher for their help in
reviewing this document.
7. IANA Considerations
This document specifies no actions for IANA.
Wenger, et al. Informational [Page 18]
INTERNET-DRAFT RTP Topologies February 22, 2007
8. References
8.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3550] Schulzrinne, H., Casner, S., Frederick, R., and V.
Jacobson, "RTP: A Transport Protocol for Real-Time
Applications", STD 64, RFC 3550, July 2003.
[RFC3711] Baugher, M., McGrew, D., Naslund, M., Carrara, E., and K.
Norrman, "The Secure Real-time Transport Protocol (SRTP)",
RFC 3711, March 2004.
[RFC4575] J. Rosenberg, H. Schulzrinne, O. Levin, "A Session
Initiation Protocol (SIP) Event Package for Conference
State", RFC 4575, August 2006
[RFC4585] Ott, J., Wenger, S., Sato, N., Burmeister, C., and J. Rey,
"Extended RTP Profile for Real-time Transport Control
Protocol (RTCP)-Based Feedback (RTP/AVPF)", RFC 4585, July
2006.
8.2. Informative References
[CCM] Wenger, S., Chandra, U., Westerlund, M., Burman, B.,
"Codec Control Messages in the Audio-Visual Profile with
Feedback (AVPF)", Internet Draft, Work in Progress,
draft-ietf-avt-avpf-ccm-04.txt>, February 2007
[H323] ITU-T Recommendation H.323, "Packet-based multimedia
communications systems", June 2006.
9. Authors' Addresses
Magnus Westerlund
Ericsson Research
Ericsson AB
SE-164 80 Stockholm, SWEDEN
Phone: +46 8 7190000
EMail: magnus.westerlund@ericsson.com
Stephan Wenger
Nokia Corporation
P.O. Box 100
FIN-33721 Tampere
FINLAND
Phone: +358-50-486-0637
EMail: stewe@stewe.org
Wenger, et al. Informational [Page 19]
INTERNET-DRAFT RTP Topologies February 22, 2007
Full Copyright Statement
Copyright (C) The IETF Trust (2007).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST
AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT
THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgement
Funding for the RFC Editor function is provided by the IETF
Administrative Support Activity (IASA).
RFC Editor Considerations
None
Wenger, et al. Informational [Page 20]
| PAFTECH AB 2003-2026 | 2026-04-23 11:05:23 |