One document matched: draft-ietf-16ng-ipv6-over-ipv6cs-10.txt
Differences from draft-ietf-16ng-ipv6-over-ipv6cs-09.txt
Network Working Group Basavaraj Patil
Internet-Draft Nokia Siemens Networks
Intended status: Standards Track Frank Xia
Expires: May 15, 2008 Behcet Sarikaya
Huawei USA
JH. Choi
Samsung AIT
Syam Madanapalli
Ordyn Technologies
November 12, 2007
Transmission of IPv6 via the IPv6 CS over IEEE 802.16 Networks
draft-ietf-16ng-ipv6-over-ipv6cs-10
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on May 15, 2008.
Copyright Notice
Copyright (C) The IETF Trust (2007).
Abstract
IEEE Std 802.16 is an air interface specification for fxed and mobile
Broadband Wireless Access Systems. Service specific convergence
Patil, et al. Expires May 15, 2008 [Page 1]
Internet-Draft IPv6 via IPv6 CS over IEEE 802.16 November 2007
sublayers to which upper layer protocols interface are a part of the
IEEE 802.16 MAC (Medium Access Control). The Packet convergence
sublayer is used for the transport of all packet-based protocols such
as Internet Protocol (IP) and, IEEE 802.3 LAN/MAN CSMA/CD Access
Method (Ethernet). IPv6 packets can be sent and received via the IP
specific part of the packet convergence sublayer. This document
specifies the addressing and operation of IPv6 over the IP specific
part of the packet CS for hosts served by a network that utilizes the
IEEE Std 802.16 air interface. It recommends the assignment of a
unique prefix (or prefixes) to each host and allows the host to use
multiple identifiers within that prefix, including support for
randomly generated interface identifiers.
Table of Contents
1. Conventions used in this document . . . . . . . . . . . . . . 4
2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. IEEE 802.16 convergence sublayer support for IPv6 . . . . . . 5
4.1. IPv6 encapsulation over the IP CS of the MAC . . . . . . . 8
5. Generic network architecture using the 802.16 air interface . 9
6. IPv6 link . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6.1. IPv6 link in 802.16 . . . . . . . . . . . . . . . . . . . 10
6.2. IPv6 link establishment in 802.16 . . . . . . . . . . . . 11
6.3. Maximum transmission unit in 802.16 . . . . . . . . . . . 12
7. IPv6 prefix assignment . . . . . . . . . . . . . . . . . . . . 12
8. Router Discovery . . . . . . . . . . . . . . . . . . . . . . . 13
8.1. Router Solicitation . . . . . . . . . . . . . . . . . . . 13
8.2. Router Advertisement . . . . . . . . . . . . . . . . . . . 13
8.3. Router lifetime and periodic router advertisements . . . . 13
9. IPv6 addressing for hosts . . . . . . . . . . . . . . . . . . 14
9.1. Interface Identifier . . . . . . . . . . . . . . . . . . . 14
9.2. Duplicate address detection . . . . . . . . . . . . . . . 14
9.3. Stateless address autoconfiguration . . . . . . . . . . . 14
9.4. Stateful address autoconfiguration . . . . . . . . . . . . 15
10. Multicast Listener Discovery . . . . . . . . . . . . . . . . . 15
11. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 15
12. Security Considerations . . . . . . . . . . . . . . . . . . . 15
13. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 15
14. References . . . . . . . . . . . . . . . . . . . . . . . . . . 16
14.1. Normative References . . . . . . . . . . . . . . . . . . . 16
14.2. Informative References . . . . . . . . . . . . . . . . . . 16
Appendix A. WiMAX network architecture and IPv6 support . . . . . 17
Appendix B. IPv6 link in WiMAX . . . . . . . . . . . . . . . . . 19
Appendix C. IPv6 link establishment in WiMAX . . . . . . . . . . 20
Appendix D. Maximum transmission unit in WiMAX . . . . . . . . . 20
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 20
Patil, et al. Expires May 15, 2008 [Page 2]
Internet-Draft IPv6 via IPv6 CS over IEEE 802.16 November 2007
Intellectual Property and Copyright Statements . . . . . . . . . . 22
Patil, et al. Expires May 15, 2008 [Page 3]
Internet-Draft IPv6 via IPv6 CS over IEEE 802.16 November 2007
1. Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
2. Introduction
IEEE 802.16e is an air interface for fixed and mobile broadband
wireless access systems. The IEEE 802.16 standard specifies the air
interface, including the medium access control (MAC) layer and
multiple physical layer (PHY) specifications. It can be deployed in
licensed as well as unlicensed spectrum. While the PHY and MAC are
specified in IEEE 802.16, the details of IPv4 and IPv6 operation over
the air interface are not included. This document specifies the
operation of IPv6 over the IEEE 802.16 air interface.
IPv6 packets can be carried over the IEEE Std 802.16 specified air
interface via :
1. the IP specific part of the Packet CS or,
2. the 802.3 [802.3] specific part of the Packet CS
The scope of this specification is limited to the operation of IPv6
over IP CS only.
The IEEE 802.16 [802.16] specification includes the Phy and MAC
details. The convergence sublayers are a part of the MAC. The
packet convergence sublayer includes the IP specific part which is
used by the IPv6 layer.
The mobile station(MS)/host is attached to an access router via a
base station (BS). The host and the BS are connected via the IEEE
Std 802.16 air interface at the link and physical layers. The IPv6
link from the MS terminates at an access router which may be a part
of the BS or an entity beyond the BS. The base station is a layer 2
entity (from the perspective of the IPv6 link between the MS and AR)
and relays the IPv6 packets between the AR and the host via a point-
to-point connection over the air interface.
3. Terminology
The terminology in this document is based on the definitions in IP
over 802.16 Problem Statement and Goals [I-D.ietf-16ng-ps-goals].
Patil, et al. Expires May 15, 2008 [Page 4]
Internet-Draft IPv6 via IPv6 CS over IEEE 802.16 November 2007
o IP CS - The IP specific part of the packet convergence sublayer is
refered to as IP CS.
o Subscriber station (SS), Mobile Station (MS), Mobile Node (MN) -
The term subscriber station, mobile station and mobile node are
used interchangeably in this document and mean the same, i.e an IP
host.
4. IEEE 802.16 convergence sublayer support for IPv6
The IEEE 802.16 MAC specifies two main service specific convergence
sublayers:
1. ATM Convergence sublayer
2. Packet Convergence sublayer
The Packet CS is used for the transport of packet based protocols
which include:
1. IEEE Std 802.3(Ethernet)
2. Internet Protocol (IPv4 and IPv6)
The service specific CS resides on top of the MAC Common Part
Sublayer (CPS) as shown in figure 1. The service specific CS is
responsible for:
o accepting packets (PDUs) from the upper layer,
o performing classification of the packet/PDU based on a set of
classifiers that are defined which are service specific,
o delivering the CS PDU to the appropriate service flow and
transport connection and,
o receiving PDUs from the peer entity.
Payload header suppression (PHS) is also a function of the CS but is
optional.
The figure below shows the concept of the service specific CS in
relation to the MAC:
Patil, et al. Expires May 15, 2008 [Page 5]
Internet-Draft IPv6 via IPv6 CS over IEEE 802.16 November 2007
-----------------------------\
| ATM CS | Packet CS | \
----------------------------- \
| MAC Common Part Sublayer | \
| (Ranging, scheduling, etc)| 802.16 MAC
----------------------------- /
| Security | /
|(Auth, encryption,key mgmt)| /
-----------------------------/
| PHY |
-----------------------------
Figure 1: The IEEE 802.16 MAC
Classifiers for each of the specific upper-layer protocols, i.e
Ethernet and IP, are defined in the IEEE 802.16 specification, which
enable the packets from the upper layer to be processed by the
appropriate service specific part of the packet CS. IPv6 can be
transported directly over the IP specific part of the packet CS (IP
CS). IPv4 packets also are transported over the IP specific part of
the packet CS. The classifiers used by IP CS enable the
differentiation of IPv4 and IPv6 packets and their mapping to
specific transport connections over the air-interface.
The figure below shows the options for IPv6 transport over the packet
CS of IEEE 802.16:
-----------------
| IPv6 |
---------------- |---------------|
| IPv6 | | Ethernet |
|--------------| |---------------|
| IP Specific | | 802.3 specific|
|part of Pkt CS| |part of Pkt CS |
|..............| |...............|
| MAC | | MAC |
|--------------| |---------------|
| PHY | | PHY |
---------------- -----------------
(1) IPv6 over (2) IPv6 over
IP Specific part 802.3/Ethernet
of Packet CS
Patil, et al. Expires May 15, 2008 [Page 6]
Internet-Draft IPv6 via IPv6 CS over IEEE 802.16 November 2007
Figure 2: IPv6 over IP and 802.3 specific parts of the Packet CS
The figure above shows that while there are multiple methods by which
IPv6 can be transmitted over an 802.16 air interface, the scope of
this document is limited to IPv6 operation over IP CS only.
Transmission of IP over Ethernet is specified in
[I-D.ietf-16ng-ip-over-ethernet-over-802.16]. Transmission of IPv4
over IP CS is specified by the 16ng WG in
[I-D.ietf-16ng-ipv4-over-802-dot-16-ipcs].
It should be noted that immediately after ranging (802.16 air
interface procedure) and exchange of SBC-REQ/RSP messages (802.16
specific), the MS and BS exchange their capabilities via REG-REQ
(Registration Request) and REG-RSP (Registration Response) 802.16 MAC
messages. These management frames negotiate parameters such as the
Convergence Sublayer supported by the MS and BS. By default, Packet,
IPv4 and 802.3/Ethernet are supported. IPv6 via the IP CS is
supported by the MS and the BS only when the IPv6 support bit in the
capability negotiation messages (REG-REQ and REG-RSP) implying such
support is indicated in the parameter "Classification/PHS options and
SDU (Service Data Unit) encapsulation support" (Refer to [802.16]).
Additionally during the establishment of the transport connection for
transporting IPv6 packets, the DSA-REQ (Dynamic Service Addition) and
DSA-RSP messages between the BS and MS indicate via the CS-
Specification TLV the CS that the connection being setup shall use.
When the IPv6 packet is preceded by the IEEE 802.16 six byte MAC
header there is no specific indication in the MAC header itself about
the payload type. The processing of the packet is based entirely on
the classifiers. Based on the classification rules, the MAC layer
selects an appropriate transport connection for the transmission of
the packet. An IPv6 packet is transported over a transport
connection that is specifically established for carrying such
packets.
Transmission of IPv6 as explained above is possible via multiple
methods, i.e, via IP CS or via Ethernet interfaces. Every Internet
host connected via an 802.16 link :
1. MUST be able to send and receive IPv6 packets via IP CS when the
MS and BS indicate IPv6 protocol support over IP CS
2. SHOULD be able to send and receive IPv6 packets over the Ethernet
(802.3) specific part of the packet CS when the MS and BS
indicate IPv6 protocol support over Ethernet CS
When the MS and BS support IPv6 over IP CS, it MUST be used as the
default mode for transporting IPv6 packets over IEEE 802.16 and the
recommendations in this document followed. Inability to negotiate a
common convergence sublayer for IPv6 transport between the MS and BS
Patil, et al. Expires May 15, 2008 [Page 7]
Internet-Draft IPv6 via IPv6 CS over IEEE 802.16 November 2007
will result in failure to setup the transport connection and thereby
render the host unable to send and receive IPv6 packets. In the case
of a host which implements more than one method of transporting IPv6
packets, the default choice of which method to use (i.e IPv6 over the
IP CS or IPv6 over 802.3) is IPv6 over IP CS when the BS also
supports such capability.
4.1. IPv6 encapsulation over the IP CS of the MAC
The IPv6 payload when carried over the IP specific part of the Packet
CS is encapsulated by the 6 byte IEEE 802.16 generic MAC header. The
format of the IPv6 packet encapsulated by the generic MAC header is
shown in the figure below. The format of the 6 byte MAC header is
described in the [802.16] specification. The CRC (cyclic redundancy
check) is optional. It should be noted that the actual MAC address
is not included in the MAC header.
---------/ /-----------
| MAC SDU |
--------/ /------------
||
||
MSB \/ LSB
---------------------------------------------------------
| Generic MAC header| IPv6 Payload | CRC |
---------------------------------------------------------
Figure 3: IPv6 encapsulation
For transmission of IPv6 packets via the IP CS over IEEE 802.16, the
IPv6 layer interfaces with the 802.16 MAC directly. The IPv6 layer
delivers the IPv6 packet to the Packet CS of the IEEE 802.16 MAC.
The packet CS defines a set of classifiers that are used to determine
how to handle the packet. The IP classifiers that are used at the
MAC operate on the fields of the IP header and the transport protocol
and these include the IP Traffic class, Next header field, Masked IP
source and destination addresses and, Protocol source and destination
port ranges. Next header in this case refers to the last header of
the IP header chain. Parsing these classifiers, the MAC maps an
upper layer packet to a specific service flow and transport
connection to be used. The MAC encapsulates the IPv6 packet in the 6
byte MAC header (MAC SDU) and transmits it. The figure below shows
the operation on the downlink, i.e the transmission from the BS to
the host. The reverse is applicable for the uplink transmission.
Patil, et al. Expires May 15, 2008 [Page 8]
Internet-Draft IPv6 via IPv6 CS over IEEE 802.16 November 2007
----------- ----------
| IPv6 Pkt| |IPv6 Pkt|
----------- ----------
| | /|\
| | |
--[SAP]--------------------- ---------[SAP]--------
||-| |----------| | | /|\ |
|| \ / 0---->[CID1] | | --- |-------- |
|| Downlink 0\/-->[CID2] | | |Reconstruct| |
|| classifiers0/\-->[....] | | | (undo PHS)| |
|| 0---->[CIDn] | | --- ------- |
||--------------| | | /|\ |
| | | | |
| {SDU, CID,..} | | {SDU, CID,..} |
| | | | /|\ |
| v | | | |
------[SAP]----------------- |-------[SAP]---------
| 802.16 MAC CPS |------>| 802.16 MAC CPS |
---------------------------- ----------------------
BS MS
Figure 4: IPv6 packet transmission: Downlink
5. Generic network architecture using the 802.16 air interface
In a network that utilizes the 802.16 air interface the host/MS is
attached to an IPv6 access router (AR) in the network. The BS is a
layer 2 entity only. The AR can be an integral part of the BS or the
AR could be an entity beyond the BS within the access network. An AR
nay be attached to multiple BS' in a network. IPv6 packets between
the MS and BS are carried over a point-to-point transport connection
which is identified by a unique connection identifier (CID). The
transport connection is a MAC layer link between the MS and the BS.
The figures below describe the possible network architectures and are
generic in nature. More esoteric architectures are possible but not
considered in the scope of this document. Option A:
+-----+ CID1 +--------------+
| MS1 |------------/| BS/AR |-----[Internet]
+-----+ / +--------------+
. /---/
. CIDn
+-----+ /
| MSn |---/
Patil, et al. Expires May 15, 2008 [Page 9]
Internet-Draft IPv6 via IPv6 CS over IEEE 802.16 November 2007
+-----+
Figure 5: The IPv6 AR as an integral part of the BS
Option B:
+-----+ CID1 +-----+ +-----------+
| MS1 |----------/| BS1 |----------| AR |-----[Internet]
+-----+ / +-----+ +-----------+
. / ____________
. CIDn / ()__________()
+-----+ / L2 Tunnel
| MSn |-----/
+-----+
Figure 6: The IPv6 AR is separate from the BS
The above network models serve as examples and are shown to
illustrate the point to point link between the MS and the AR.
6. IPv6 link
Neighbor Discovery for IP Version 6 [RFC4861] defines link as a
communication facility or medium over which nodes can communicate at
the link layer, i.e., the layer immediately below IP . A link is
bounded by routers that decrement the Hop limit field in the IPv6
header. When an MS moves within a link, it can keep using its IP
addresses. This is a layer 3 definition and note that the definition
is not identical with the definition of the term '(L2) link' in IEEE
802 standards.
6.1. IPv6 link in 802.16
In 802.16, the Transport Connection between an MS and a BS is used to
transport user data, i.e. IPv6 packets in this case. A Transport
Connection is represented by a CID (Connection Identifier) and
multiple Transport Connections can exist between an MS and BS.
When an AR and a BS are colocated, the collection of Transport
Connections to an MS is defined as a single link. When an AR and a
BS are separated, it is recommended that a tunnel is established
between the AR and a BS whose granularity is no greater than 'per MS'
Patil, et al. Expires May 15, 2008 [Page 10]
Internet-Draft IPv6 via IPv6 CS over IEEE 802.16 November 2007
or 'per service flow' ( An MS can have multiple service flows which
are identified by a service flow ID). Then the tunnel(s) for an MS,
in combination with the MS's Transport connections, forms a single
point-to-point link.
The collection of service flows (tunnels) to an MS is defined as a
single link. Each link that use the same higher layer protocol has
only an MS and an AR. Each MS belongs to a different link. A
different prefix should be assigned to each unique link. This link
is fully consistent with a standard IP link, without exception and
conforms with the definition of a point-to-point link in Neighbor
discovery for IPv6 [RFC4861]. Hence the point-to-point link model
for IPv6 operation over the IP specific part of the Packet CS in
802.16 SHOULD be used. A unique IPv6 prefix(es) per link (MS/host)
MUST be assigned.
6.2. IPv6 link establishment in 802.16
In order to enable the sending and receiving of IPv6 packets between
the MS and the AR, the link between the MS and the AR via the BS
needs to be established. This section illustrates the link
establishment procedure.
The MS goes through the network entry procedure as specified by
802.16. A high level description of the network entry procedure is
as follows:
1. MS performs initial ranging with the BS. Ranging is a process by
which an MS becomes time aligned with the BS. The MS is
synchronized with the BS at the successful completion of ranging
and is ready to setup a connection.
2. The MS and BS exchange basic capabilities that are necessary for
effective communication during the initialization using SBC-REQ/
RSP (802.16 specific) messages.
3. The MS progresses to an authentication phase. Authentication is
based on PKMv2 as defined in the IEEE Std 802.16 specification.
4. On successful completion of authentication, the MS performs
802.16 registration with the network.
5. MS and BS perform capability exchange as per 802.16 procedures.
Protocol support is indicated in this exchange. The CS
capability parameter indicates which classification/PHS options
and SDU encapsulation the MS supports. By default, Packet, IPv4
and 802.3/Ethernet shall be supported, thus absence of this
parameter in REG-REQ (802.16 message) means that named options
are supported by the MS/SS. Support for IPv6 over the IP
specific part of the packet CS is indicated by Bit#2 of the CS
capability parameter (Refer to [802.16]).
Patil, et al. Expires May 15, 2008 [Page 11]
Internet-Draft IPv6 via IPv6 CS over IEEE 802.16 November 2007
6. The MS MUST request the establishment of a service flow for IPv6
packets over IP CS if the MS and BS have confirmed capability for
supporting IPv6 over IP CS. The service flow MAY also be
triggered by the network as a result of pre-provisioning. The
service flow establishes a link between the MS and the AR over
which IPv6 packets can be sent and received.
7. The AR and MS SHOULD send router advertisements and solicitations
as specified in Neighbor discovery,[RFC4861].
The above flow does not show the actual 802.16 messages that are used
for ranging, capability exchange or service flow establishment.
Details of these are in [802.16].
6.3. Maximum transmission unit in 802.16
The MTU value for IPv6 packets on an 802.16 link is configurable.
The default MTU for IPv6 packets over an 802.16 link MUST be 1500
octets.
The 802.16 MAC PDU (Protocol Data Unit) is composed of a 6 byte
header followed by an optional payload and an optional CRC covering
the header and the payload. The length of the PDU is indicated by
the Len parameter in the Generic MAC Header. The Len parameter has a
size of 11 bits. Hence the total MAC PDU size is 2048 bytes. The
IPv6 payload size can vary. In certain deployment scenarios the MTU
value can be greater than the default. Neighbor Discovery for IPv6
[RFC4861] defines an MTU option that an AR can advertise, via router
advertisement (RA), to a Mobile Node (MN). If an AR advertises an
MTU via the RA MTU option, the MN SHOULD use the MTU from the RA.
Nodes that implement Path MTU discovery [RFC1981] MAY use the
mechanism to determine the MTU for the IPv6 packets.
7. IPv6 prefix assignment
The MS and the AR are connected via a point-to-point connection at
the IPv6 layer. Hence each MS can be considered to be on a separate
subnet. A CPE (Customer Premise Equipment) type of device which
serves multiple IPv6 hosts, may be the end point of the connection.
Hence one or more /64 prefixes SHOULD be assigned to a link. The
prefixes are advertised with the on-link (L-bit) flag set as
specified in [RFC4861]. The size and number of the prefixes is a
configuration issue. Also, DHCP or AAA-based prefix delegation MAY
be used to provide one or more prefixes to MS for an AR connected
over 802.16. The other properties of the prefixes are also dealt
with via configuration.
Patil, et al. Expires May 15, 2008 [Page 12]
Internet-Draft IPv6 via IPv6 CS over IEEE 802.16 November 2007
8. Router Discovery
8.1. Router Solicitation
On completion of the establishment of the IPv6 link, the MS may send
a router solicitation message to solicit a Router Advertisement
message from the AR to acquire necessary information as per the
neighbor discovery for IPv6 specification [RFC4861]. An MS that is
network attached may also send router solicitations at any time.
Movement detection at the IP layer of an MS in many cases is based on
receiving periodic router advertisements. An MS may also detect
changes in its attachment via link triggers or other means. The MS
can act on such triggers by sending router solicitations. The router
solicitation is sent over the IPv6 link that has been previously
established. The MS sends router solicitations to the all-routers
multicast address. It is carried over the point-to-point link to the
AR via the BS. The MS does not need to be aware of the link-local
address of the AR in order to send a router solicitation at any time.
The use of router advertisements as a means for movement detection is
not recommended for MNs connected via 802.16 links as the frequency
of periodic router advertisements can be high.
8.2. Router Advertisement
The AR SHOULD send a number (configurable value) of router
advertisements as soon as the IPv6 link is established, to the MS.
The AR sends unsolicited router advertisements periodically as per
[RFC4861]. The interval between periodic router advertisements is
however greater than the specification in Neighbor discovery for
IPv6, and is discussed in the following section.
8.3. Router lifetime and periodic router advertisements
The router lifetime SHOULD be set to a large value, preferably in
hours. This document over-rides the specification for the value of
the router lifetime in Neighbor Discovery for IP Version 6 (IPv6)
[RFC4861]. The AdvDefaultLifetime in the router advertisement MUST
be either zero or between MaxRtrAdvInterval and 43200 seconds. The
default value is 2 * MaxRtrAdvInterval.
802.16 hosts have the capability to transition to an idle mode in
which case the radio link between the BS and MS is torn down. Paging
is required in case the network needs to deliver packets to the MS.
In order to avoid waking a mobile which is in idle mode and consuming
resources on the air interface, the interval between periodic router
advertisements SHOULD be set quite high. The MaxRtrAdvInterval value
specified in this document over-rides the recommendation in Neighbor
Discovery for IP Version 6 (IPv6) [RFC4861]. The MaxRtrAdvInterval
Patil, et al. Expires May 15, 2008 [Page 13]
Internet-Draft IPv6 via IPv6 CS over IEEE 802.16 November 2007
MUST be no less than 4 seconds and no greater than 21600 seconds.
The default value for MaxRtrAdvInterval is 10800 seconds.
9. IPv6 addressing for hosts
The addressing scheme for IPv6 hosts in 802.16 networks follows the
IETFs recommendation for hosts specified in IPv6 Node Requirement,
RFC 4294. The IPv6 node requirements RFC4294 [RFC4294] specifies a
set of RFCs that are applicable for addressing and the same is
applicable for hosts that use 802.16 as the link layer for
transporting IPv6 packets.
9.1. Interface Identifier
The MS has a 48-bit globally unique MAC address as specified in
802.16 [802.16]. This MAC address MUST be used to generate the
modified EUI-64 format-based interface identifier as specified in the
IP Version 6 Addressing Architecture [RFC4291]. The modified EUI-64
interface identifier is used in stateless address autoconfiguration.
As in other links that support IPv6, EUI-64 based interface
identifiers are not mandatory and other mechanisms, such as random
interface identifiers, Privacy Extensions for Stateless Address
Autoconfiguration in IPv6 [RFC3041] MAY also be used.
9.2. Duplicate address detection
DAD SHOULD be performed as per Neighbor Discovery for IP Version 6,
[RFC4861] and, IPv6 Stateless Address Autoconfiguration, [RFC4862].
The IPv6 link over 802.16 is specified in this document as a point-
to-point link. Based on this criteria, it may be redundant to
perform DAD on a global unicast address that is configured using the
EUI-64 or generated as per RFC3041 [RFC3041] for the interface as
part of the IPv6 stateless address autoconfiguration protocol
[RFC4862] as long as the following two conditions are met:
1. The prefixes advertised through the router advertisement messages
by the access router terminating the 802.16 IPv6 link are unique
to that link.
2. The access router terminating the 802.16 IPv6 link does not
autoconfigure any IPv6 global unicast addresses from the prefix
that it advertises.
9.3. Stateless address autoconfiguration
When stateless address autoconfiguration is performed, it MUST be
performed as specified in [RFC4861] and, [RFC4862].
Patil, et al. Expires May 15, 2008 [Page 14]
Internet-Draft IPv6 via IPv6 CS over IEEE 802.16 November 2007
9.4. Stateful address autoconfiguration
When stateful address autoconfiguration is performed, it MUST be
performed as specified in [RFC4861] and, [RFC3315].
10. Multicast Listener Discovery
Multicast Listener Discovery Version 2 (MLDv2) for IPv6 [RFC4861]
SHOULD be supported as specified by the hosts and routers attached to
each other via an 802.16 link. The access router which has hosts
attached to it via a Point-to-point link over an 802.16 SHOULD NOT
send periodic queries if the host is in idle/dormant mode. The AR
can obtain information about the state of a host from the paging
controller in the network.
11. IANA Considerations
This draft does not require any actions from IANA.
12. Security Considerations
This document does not introduce any new vulnerabilities to IPv6
specifications or operation. The security of the 802.16 air
interface is the subject of [802.16]. It should be noted that 802.16
provides capability to cipher the traffic carried over the transport
connections. A traffic encryption key (TEK) is generated by the MS
and BS on completion of successful authentication and is used to
secure the traffic over the air interface. An MS may still use IPv6
security mechanisms even in the presence of security over the 802.16
link. In addition, the security issues of the network architecture
spanning beyond the 802.16 base stations is the subject of the
documents defining such architectures, such as WiMAX Network
Architecture [WiMAXArch] in Sections 7.2 and 7.3 of Stage 2 Part 2.
13. Acknowledgments
The authors would like to acknowledge the contributions of the 16NG
working group chairs Soohong Daniel Park and Gabriel Montenegro as
well as Jari Arkko, Jonne Soininen, Max Riegel, Prakash Iyer, DJ
Johnston, Dave Thaler, Bruno Sousa, Alexandru Petrescu, Margaret
Wasserman and Pekka Savola for their review and comments. Review and
comments by Phil Barber have also helped in improving the document
quality.
Patil, et al. Expires May 15, 2008 [Page 15]
Internet-Draft IPv6 via IPv6 CS over IEEE 802.16 November 2007
14. References
14.1. Normative References
[802.16] "IEEE Std 802.16e: IEEE Standard for Local and
metropolitan area networks, Amendment for Physical and
Medium Access Control Layers for Combined Fixed and Mobile
Operation in Licensed Bands", October 2005, <http://
standards.ieee.org/getieee802/download/802.16e-2005.pdf>.
[RFC1981] McCann, J., Deering, S., and J. Mogul, "Path MTU Discovery
for IP version 6", RFC 1981, August 1996.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", RFC 2119, March 1997,
<ftp://ftp.isi.edu/in-notes/rfc2119>.
[RFC3810] Vida, R. and L. Costa, "Multicast Listener Discovery
Version 2 (MLDv2) for IPv6", RFC 3810, June 2004.
[RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing
Architecture", RFC 4291, February 2006.
[RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
"Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
September 2007.
[RFC4862] Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless
Address Autoconfiguration", RFC 4862, September 2007.
14.2. Informative References
[802.3] "IEEE Std 802.3-2005: IEEE Standard for Information
technology-Telecommunications and information exchange
between systems-Local and metropolitan area networks--
Specific requirements Part 3: Carrier Sense Multiple
Access with Collision Detection (CSMA/CD) Access Method
and Physical Layer Specifications", December 2005,
<http://standards.ieee.org/getieee802/802.3.html>.
[I-D.ietf-16ng-ip-over-ethernet-over-802.16]
Jeon, H., "Transmission of IP over Ethernet over IEEE
802.16 Networks",
draft-ietf-16ng-ip-over-ethernet-over-802.16-02 (work in
progress), July 2007.
[I-D.ietf-16ng-ipv4-over-802-dot-16-ipcs]
Madanapalli, S., "Transmission of IPv4 packets over IEEE
Patil, et al. Expires May 15, 2008 [Page 16]
Internet-Draft IPv6 via IPv6 CS over IEEE 802.16 November 2007
802.16's IP Convergence Sublayer",
draft-ietf-16ng-ipv4-over-802-dot-16-ipcs-00 (work in
progress), May 2007.
[I-D.ietf-16ng-ps-goals]
Jee, J., "IP over 802.16 Problem Statement and Goals",
draft-ietf-16ng-ps-goals-02 (work in progress),
August 2007.
[RFC3041] Narten, T. and R. Draves, "Privacy Extensions for
Stateless Address Autoconfiguration in IPv6", RFC 3041,
January 2001.
[RFC3315] Droms, R., Bound, J., Volz, B., Lemon, T., Perkins, C.,
and M. Carney, "Dynamic Host Configuration Protocol for
IPv6 (DHCPv6)", RFC 3315, July 2003.
[RFC4294] Loughney, J., "IPv6 Node Requirements", RFC 4294,
April 2006.
[WMF] "http://www.wimaxforum.org".
[WiMAXArch]
"WiMAX End-to-End Network Systems Architecture
http://www.wimaxforum.org/technology/documents",
August 2006.
Appendix A. WiMAX network architecture and IPv6 support
The WiMAX (Worldwide Interoperability for Microwave Access) forum
[WMF] has defined a network architecture in which the air interface
is based on the IEEE 802.16 standard. The addressing and operation
of IPv6 described in this document is applicable to the WiMAX network
as well.
WiMAX is an example architecture of a network that uses the 802.16
specification for the air interface. WiMAX networks are also in the
process of being deployed in various parts of the world and the
operation of IPv6 within a WiMAX network is explained in this
appendix.
The WiMAX network architecture consists of the Access Service Network
(ASN) and the Connectivity Service Network (CSN). The ASN is the
access network which includes the BS and the AR in addition to other
functions such as AAA, Mobile IP Foreign agent, Paging controller,
Location Register etc. The ASN is defined as a complete set of
network functions needed to provide radio access to a WiMAX
Patil, et al. Expires May 15, 2008 [Page 17]
Internet-Draft IPv6 via IPv6 CS over IEEE 802.16 November 2007
subscriber. The ASN is the access network to which the MS attaches.
The IPv6 access router is an entity within the ASN. The term ASN is
specific to the WiMAX network architecture. The CSN is the entity
that provides connectivity to the Internet and includes functions
such as Mobile IP Home agent and AAA. The figure below shows the
WiMAX reference model:
-------------------
| ---- ASN | |----|
---- | |BS|\ R6 -------| |---------| | CSN|
|MS|-----R1----| ---- \---|ASN-GW| R3 | CSN | R5 | |
---- | |R8 /--|------|----| |-----|Home|
| ---- / | | visited| | NSP|
| |BS|/ | | NSP | | |
| ---- | |---------| | |
| NAP | \ |----|
------------------- \---| /
| | /
| (--|------/----)
|R4 ( )
| ( ASP network )
--------- ( or Internet )
| ASN | ( )
--------- (----------)
Figure 7: WiMAX Network reference model
Three different types of ASN realizations called profiles are defined
by the architecture. ASNs of profile types A and C include BS' and
ASN-gateway(s) (ASN-GW) which are connected to each other via an R6
interface. An ASN of profile type B is one in which the
functionality of the BS and other ASN functions are merged together.
No ASN-GW is specifically defined in a profile B ASN. The absence of
the R6 interface is also a profile B specific characteristic. The MS
at the IPv6 layer is associated with the AR in the ASN. The AR may
be a function of the ASN-GW in the case of profiles A and C and is a
function in the ASN in the case of profile B. When the BS and the AR
are separate entities and linked via the R6 interface, IPv6 packets
between the BS and the AR are carried over a GRE tunnel. The
granularity of the GRE tunnel should be on a per MS basis or on a per
service flow basis (an MS can have multiple service flows, each of
which are identified uniquely by a service flow ID). The protocol
stack in WiMAX for IPv6 is shown below:
Patil, et al. Expires May 15, 2008 [Page 18]
Internet-Draft IPv6 via IPv6 CS over IEEE 802.16 November 2007
|-------|
| App |- - - - - - - - - - - - - - - - - - - - - - - -(to app peer)
| |
|-------| /------ -------
| | / IPv6 | | |
| IPv6 |- - - - - - - - - - - - - - - - / | | |-->
| | --------------- -------/ | | IPv6|
|-------| | \Relay/ | | | |- - - | |
| | | \ / | | GRE | | | |
| | | \ /GRE | - | | | | |
| |- - - | |-----| |------| | | |
| IPv6CS| |IPv6CS | IP | - | IP | | | |
| ..... | |...... |-----| |------|--------| |-----|
| MAC | | MAC | L2 | - | L2 | L2 |- - - | L2 |
|-------| |------ |-----| |----- |--------| |-----|
| PHY |- - - | PHY | L1 | - | L1 | L1 |- - - | L1 |
-------- --------------- ----------------- -------
MS BS AR/ASN-GW CSN Rtr
Figure 8: WiMAX protocol stack
As can be seen from the protocol stack description, the IPv6 end-
points are constituted in the MS and the AR. The BS provides lower
layer connectivity for the IPv6 link.
Appendix B. IPv6 link in WiMAX
WiMAX is an example of a network based on the IEEE Std 802.16 air
interface. This section describes the IPv6 link in the context of a
WiMAX network. The MS and the AR are connected via a combination of
:
1. The transport connection which is identified by a Connection
Identifier (CID) over the air interface, i.e the MS and BS and,
2. A GRE tunnel between the BS and AR which transports the IPv6
packets
From an IPv6 perspective the MS and the AR are connected by a point-
to-point link. The combination of transport connection over the air
interface and the GRE tunnel between the BS and AR creates a (point-
to-point) tunnel at the layer below IPv6.
The collection of service flows (tunnels) to an MS is defined as a
single link. Each link has only an MS and an AR. Each MS belongs to
Patil, et al. Expires May 15, 2008 [Page 19]
Internet-Draft IPv6 via IPv6 CS over IEEE 802.16 November 2007
a different link. No two MSs belong to the same link. A different
prefix should be assigned to each unique link. This link is fully
consistent with a standard IP link, without exception and conforms
with the definition of a point-to-point link in [RFC4861].
Appendix C. IPv6 link establishment in WiMAX
The mobile station performs initial network entry as specified in
802.16. On successful completion of the network entry procedure the
ASN gateway/AR triggers the establishment of the initial service flow
(ISF) for IPv6 towards the MS. The ISF is a GRE tunnel between the
ASN-GW/AR and the BS. The BS in turn requests the MS to establish a
transport connection over the air interface. The end result is a
transport connection over the air interface for carrying IPv6 packets
and a GRE tunnel between the BS and AR for relaying the IPv6 packets.
On successful completion of the establishment of the ISF, IPv6
packets can be sent and received between the MS and AR. The ISF
enables the MS to communicate with the AR for host configuration
procedures. After the establishment of the ISF, the AR can send a
router advertisement to the MS. An MS can establish multiple service
flows with different QoS characteristics. The ISF can be considered
as the primary service flow. The ASN-GW/ AR treats each ISF, along
with the other service flows to the same MS, as a unique link which
is managed as a (virtual) interface.
Appendix D. Maximum transmission unit in WiMAX
The WiMAX forum [WMF] has specified the Max SDU size as 1522 octets.
Hence the IPv6 path MTU can be 1500 octets. However because of the
overhead of the GRE tunnel used to transport IPv6 packets between the
BS and AR and the 6 byte MAC header over the air interface, using a
value of 1500 would result in fragmentation of packets. It is
recommended that the default MTU for IPv6 be set to 1400 octets for
the MS in WiMAX networks. Note that the 1522 octet specification is
a WiMAX forum specification and not the size of the SDU that can be
transmitted over 802.16, which has a higher limit.
Patil, et al. Expires May 15, 2008 [Page 20]
Internet-Draft IPv6 via IPv6 CS over IEEE 802.16 November 2007
Authors' Addresses
Basavaraj Patil
Nokia Siemens Networks
6000 Connection Drive
Irving, TX 75039
USA
Email: basavaraj.patil@nsn.com
Frank Xia
Huawei USA
1700 Alma Dr. Suite 100
Plano, TX 75075
Email: xiayangsong@huawei.com
Behcet Sarikaya
Huawei USA
1700 Alma Dr. Suite 100
Plano, TX 75075
Email: sarikaya@ieee.org
JinHyeock Choi
Samsung AIT
Networking Technology Lab
P.O.Box 111
Suwon, Korea 440-600
Email: jinchoe@samsung.com
Syam Madanapalli
Ordyn Technologies
1st Floor, Creator Building, ITPL.
Off Airport Road
Bangalore, India 560066
Email: smadanapalli@gmail.com
Patil, et al. Expires May 15, 2008 [Page 21]
Internet-Draft IPv6 via IPv6 CS over IEEE 802.16 November 2007
Full Copyright Statement
Copyright (C) The IETF Trust (2007).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgment
Funding for the RFC Editor function is provided by the IETF
Administrative Support Activity (IASA).
Patil, et al. Expires May 15, 2008 [Page 22]
| PAFTECH AB 2003-2026 | 2026-04-24 10:53:37 |