One document matched: draft-briscoe-tsvwg-cl-architecture-02.txt
Differences from draft-briscoe-tsvwg-cl-architecture-01.txt
TSVWG B. Briscoe
Internet Draft P. Eardley
draft-briscoe-tsvwg-cl-architecture-02.txt D. Songhurst
Expires: September 2006 BT
F. Le Faucheur
A. Charny
Cisco Systems, Inc
J. Babiarz
K. Chan
S. Dudley
Nortel
March 6, 2006
A Framework for Admission Control over DiffServ using Pre-Congestion
Notification
draft-briscoe-tsvwg-cl-architecture-02.txt
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress".
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
This Internet-Draft will expire on September 6, 2006.
Briscoe Expires September 6, 2006 [Page 1]
Internet-Draft Framework using Pre-Congestion Notification March 2006
Copyright Notice
Copyright (C) The Internet Society (2006). All Rights Reserved.
Abstract
This document describes a framework to achieve an end-to-end
Controlled Load (CL) service without the scalability problems of
previous approaches. Flow admission control and if necessary flow
pre-emption preserve the CL service to admitted flows. But interior
routers within a large DiffServ-based region of the Internet do not
require flow state or signalling. They only have to give early
warning of their own congestion by bulk packet marking using new pre-
congestion notification marking. Gateways around the edges of the
region convert measurements of this packet granularity marking into
admission control and pre-emption functions at flow granularity.
Authors' Note (TO BE DELETED BY THE RFC EDITOR UPON PUBLICATION)
This document is posted as an Internet-Draft with the intention of
eventually becoming an INFORMATIONAL RFC, rather than a standards
track document.
Table of Contents
1. Introduction................................................4
1.1. Summary................................................4
1.1.1. Flow admission control.............................5
1.1.2. Flow pre-emption...................................7
1.1.3. Both admission control and pre-emption.............8
1.2. Terminology............................................9
1.3. Existing terminology...................................10
1.4. Standardisation requirements...........................10
1.5. Structure of rest of the document......................11
2. Key aspects of the framework................................12
2.1. Key goals.............................................12
2.2. Key assumptions........................................13
2.3. Key benefits..........................................15
3. Architecture...............................................18
3.1. Admission control......................................18
3.1.1. Pre-Congestion Notification for Admission Marking..18
3.1.2. Measurements to support admission control..........18
Briscoe Expires September 6, 2006 [Page 2]
Internet-Draft Framework using Pre-Congestion Notification March 2006
3.1.3. How edge-to-edge admission control supports end-to-end
QoS signalling..........................................19
3.1.4. Use case.........................................19
3.2. Flow pre-emption.......................................20
3.2.1. Alerting an ingress gateway that flow pre-emption may be
needed..................................................20
3.2.2. Determining the right amount of CL traffic to drop.23
3.2.3. Use case for flow pre-emption.....................24
4. Details....................................................26
4.1. Ingress gateways.......................................26
4.2. Interior nodes........................................27
4.3. Egress gateways........................................27
4.4. Failures..............................................28
4.5. Admission of 'emergency / higher precedence' session....29
4.6. Tunnelling............................................30
5. Potential future extensions.................................32
5.1. Mechanisms to deal with 'Flash crowds'.................32
5.2. Multi-domain and multi-operator usage..................33
5.3. Adaptive bandwidth for the Controlled Load service......33
5.4. Controlled Load service with end-to-end Pre-Congestion
Notification...............................................34
5.5. MPLS-TE...............................................34
6. Relationship to other QoS mechanisms........................35
6.1. IntServ Controlled Load................................35
6.2. Integrated services operation over DiffServ............35
6.3. Differentiated Services................................35
6.4. ECN...................................................36
6.5. RTECN.................................................36
6.6. RMD...................................................36
6.7. RSVP Aggregation over MPLS-TE..........................37
7. Security Considerations.....................................37
8. Acknowledgements...........................................38
9. Comments solicited.........................................38
10. Changes from earlier versions of the draft.................38
11. Appendices................................................39
11.1. Appendix A: Explicit Congestion Notification..........39
11.2. Appendix B: What is distributed measurement-based admission
control?...................................................40
11.3. Appendix C: Calculating the Exponentially weighted moving
average (EWMA).............................................41
12. References................................................43
Authors' Addresses............................................46
Intellectual Property Statement................................48
Disclaimer of Validity........................................48
Copyright Statement...........................................49
Briscoe Expires September 6, 2006 [Page 3]
Internet-Draft Framework using Pre-Congestion Notification March 2006
1. Introduction
1.1. Summary
This document describes a framework to achieve an end-to-end
controlled load service by using - within a large region of the
Internet - DiffServ and edge-to-edge distributed measurement-based
admission control and flow pre-emption. Controlled load service is a
quality of service (QoS) closely approximating the QoS that the same
flow would receive from a lightly loaded network element [RFC2211].
Controlled Load (CL) is useful for inelastic flows such as those for
real-time media.
In line with the "IntServ over DiffServ" framework defined in
[RFC2998], the CL service is supported end-to-end and RSVP signalling
[RFC2205] is used end-to-end, over an edge-to-edge DiffServ region.
___ ___ _______________________________________ ____ ___
| | | | | | | | | |
| | | | |Ingress Interior Egress| | | | |
| | | | |gateway nodes gateway| | | | |
| | | | |-------+ +-------+ +-------+ +------| | | | |
| | | | | PCN- | | PCN- | | PCN- | | | | | | |
| |..| |..|marking|..|marking|..|marking|..| Meter|..| |..| |
| | | | |-------+ +-------+ +-------+ +------| | | | |
| | | | | \ / | | | | |
| | | | | \ / | | | | |
| | | | | \ Congestion-Level-Estimate / | | | | |
| | | | | \ (for admission control) / | | | | |
| | | | | --<-----<----<----<-----<-- | | | | |
| | | | | Sustainable-Aggregate-Rate | | | | |
| | | | | (for flow pre-emption) | | | | |
|___| |___| |_______________________________________| |____| |___|
Sx Access CL-region Access Rx
End Network Network End
Host Host
<------ edge-to-edge signalling ----->
(for admission control & flow pre-emption)
<-------------------end-to-end QoS signalling protocol--------------->
Figure 1: Overall QoS architecture (NB terminology explained later)
Briscoe Expires September 6, 2006 [Page 4]
Internet-Draft Framework using Pre-Congestion Notification March 2006
In Section 1.1.1 we summarise how admission of new CL microflows is
controlled so as to deliver the required QoS. In abnormal
circumstances for instance a disaster affecting multiple interior
nodes, then the QoS on existing CL microflows may degrade even if
care was exercised when admitting those microflows before those
circumstances. Therefore we also propose a mechanism (summarised in
Section 1.1.2) to pre-empt some of the existing microflows. Then
remaining microflows retain their expected QoS, while improved QoS is
quickly restored to lower priority traffic.
As a fundamental building block to support these two mechanisms, we
introduce "Pre-Congestion Notification". Pre-Congestion Notification
(PCN) builds on the concepts of RFC 3168, "The addition of Explicit
Congestion Notification to IP". The draft [PCN] proposes the
respective algorithms that determine when a PCN-enabled router marks
a packet with Admission Marking or Pre-emption Marking, depending on
the traffic level.
Pre-Congestion Notification can supplement any Per Hop Behaviour. In
order to support CL traffic we would expect it to supplement the
existing Expedited Forwarding (EF). Within the controlled edge-to-
edge region, a particular packet receives the Pre-Congestion
Notification behaviour if the packet's DSCP (differentiated services
codepoint) is set to EF (or whatever is configured for CL traffic)
and also the ECN field indicates ECN Capable Transport.
There are various possible ways to encode the markings into a packet,
using the ECN field and perhaps other DSCPs, which are discussed in
[PCN]. In this draft we use the abstract names Admission Marking and
Pre-emption Marking.
This framework assumes that the Pre-Congestion Notification behaviour
is used in a controlled environment, i.e. within the controlled edge-
to-edge region.
1.1.1. Flow admission control
This document describes a new admission control procedure for an
edge-to-edge region, which uses new per-hop Pre-Congestion
Notification 'admission marking' as a fundamental building block. In
turn, an end-to-end CL service would use this as a building block
within a broader QoS architecture.
Briscoe Expires September 6, 2006 [Page 5]
Internet-Draft Framework using Pre-Congestion Notification March 2006
The per-hop, edge-to-edge and end-to-end aspects are now briefly
introduced in turn.
Appendix A provides a brief summary of Explicit Congestion
Notification (ECN) [RFC3168]. It specifies that a router sets the ECN
field to the Congestion Experienced (CE) value as a warning of
incipient congestion. RFC3168 doesn't specify a particular algorithm
for setting the CE codepoint, although RED (Random Early Detection)
is expected to be used.
Pre-Congestion Notification (PCN) builds on the concepts of ECN. PCN
introduces a new algorithm that Admission Marks packets before there
is any significant build-up of CL packets in the queue. Admission
marked packets therefore act as an "early warning" when the amount of
packets flowing is getting close to the engineered capacity. Hence it
can be used with per-hop behaviours (PHBs) designed to operate with
very low queue occupancy, such as Expedited Forwarding (EF). Note
that our use of the ECN field operates across the CL-region, i.e.
edge-to-edge, and not host-to-host as in [RFC3168].
Turning next to the edge-to-edge aspect. All nodes within a region of
the Internet, which we call the CL-region, apply the PHB used for CL
traffic and the Pre-Congestion Notification behaviour. Traffic must
enter/leave the CL-region through ingress/egress gateways, which have
special functionality. Typically the CL-region is the core or
backbone of an operator. The CL service is achieved "edge-to-edge"
across the CL-region, by using distributed measurement-based
admission control: the decision whether to admit a new microflow
depends on a measurement of the existing traffic between the same
pair of ingress and egress gateways (i.e. the same pair as the
prospective new microflow). (See Appendix B for further discussion on
"What is distributed measurement-based admission control?")
As CL packets travel across the CL-region, nodes will admission mark
packets (according to the Pre-Congestion Notification algorithm) as
an "early warning" of potential congestion, i.e. before there is any
significant build-up of CL packets in the queue. For traffic from
each remote ingress gateway, the CL-region's egress gateway measures
the fraction of CL traffic that is admission marked. The egress
gateway calculates the value on a per bit basis as an exponentially
weighted moving average (which we term Congestion-Level-Estimate).
Then it reports it to the CL-region's ingress gateway piggy-backed on
the signalling for a new flow. The ingress gateway only admits the
new CL microflow if the Congestion-Level-Estimate is less than the
value of the CLE-threshold. Hence previously accepted CL microflows
will suffer minimal queuing delay, jitter and loss.
Briscoe Expires September 6, 2006 [Page 6]
Internet-Draft Framework using Pre-Congestion Notification March 2006
In turn, the edge-to-edge architecture is a building block in
delivering an end-to-end CL service. The approach is similar to that
described in [RFC2998] for Integrated services operation over
DiffServ networks. Like [RFC2998], an IntServ class (CL in our case)
is achieved end-to-end, with a CL-region viewed as a single
reservation hop in the total end-to-end path. Interior nodes of the
CL-region do not process flow signalling nor do they hold state. We
assume that the end-to-end signalling mechanism is RSVP (Section
2.2). However, the RSVP signalling may itself be originated or
terminated by proxies still closer to the edge of the network, such
as home hubs or the like, triggered in turn by application layer
signalling. [RFC2998] and our approach are compared further in
Section 6.2.
An important benefit compared with the IntServ over DiffServ model
[RFC2998] arises from the fact that the load is controlled
dynamically rather than with the traffic conditioning agreements
(TCAs). TCAs were originally introduced in the (informational)
DiffServ architecture [RFC2475] as an alternative to reservation
processing in the interior region in order to reduce the burden on
interior nodes. With TCAs, in practice service providers rely on
subscription-time Service Level Agreements that statically define the
parameters of the traffic that will be accepted from a customer. The
problem arises because the TCA at the ingress must allow any
destination address, if it is to remain scalable. But for longer
topologies, the chances increase that traffic will focus on an
interior resource, even though it is within contract at the ingress
[Reid], e.g. all flows converge on the same egress gateway. Even
though networks can be engineered to make such failures rare, when
they occur all inelastic flows through the congested resource fail
catastrophically.
Distributed measurement-based admission control avoids reservation
processing (whether per flow or aggregated) on interior nodes but
flows are still blocked dynamically in response to actual congestion
on any interior node. Hence there is no need for accurate or
conservative prediction of the traffic matrix.
1.1.2. Flow pre-emption
An essential QoS issue in core and backbone networks is being able to
cope with failures of nodes and links. The consequent re-routing can
cause severe congestion on some links and hence degrade the QoS
experienced by on-going microflows and other, lower priority traffic.
Even when the network is engineered to sustain a single link failure,
multiple link failures (e.g. due to a fibre cut or a node failure, or
a natural disaster) can cause violation of capacity constraints and
Briscoe Expires September 6, 2006 [Page 7]
Internet-Draft Framework using Pre-Congestion Notification March 2006
resulting QoS failures. Our solution uses rate-based flow pre-
emption, so that sufficient of the previously admitted CL microflows
are dropped to ensure that the remaining ones again receive QoS
commensurate with the CL service and at least some QoS is quickly
restored to other traffic classes.
The solution has two aspects. First, triggering the ingress gateway
to test whether pre-emption may be needed. A router enhanced with
Pre-Congestion Notification may optionally include an algorithm that
sets packets into the Pre-emption Marked state. Such a packet alerts
the egress that pre-emption may be needed, which in turn sends a Pre-
emption Alert message to the ingress. Secondly, calculating the right
amount of traffic to drop. This involves the egress gateway
measuring, and reporting to the ingress gateway, the current amount
of CL traffic received from that particular ingress gateway. The
ingress gateway compares this measurement (which is the amount that
the network can actually support, and which we thus call the
Sustainable-Aggregate-Rate) with the rate that it is sending and
hence determines how much traffic needs to be pre-empted.
The solution operates within a little over one round trip time - the
time required for microflow packets that have experienced Pre-emption
Marking to travel downstream through the CL-region and arrive at the
egress gateway, plus some additional time for the egress gateway to
measure the rate seen after it has been alerted that pre-emption may
be needed, and the time for the egress gateway to report this
information to the ingress gateway.
1.1.3. Both admission control and pre-emption
This document describes both the admission control and pre-emption
mechanisms, and we suggest that an operator uses both. However, we do
not require this and some operators may want to implement only one.
For example, an operator could use just admission control, solving
heavy congestion (caused by re-routing) by 'just waiting' - as
sessions end, existing microflows naturally depart from the system
over time, and the admission control mechanism will prevent admission
of new microflows that use the affected links. So the CL-region will
naturally return to normal controlled load service, but with reduced
capacity. The drawback of this approach would be that until flows
naturally depart to relieve the congestion, all flows and lower
priority services will be adversely affected. As another example, an
operator could use just admission control, avoiding heavy congestion
(caused by re-routing) by 'capacity planning' - by configuring
admission control thresholds to lower levels than the network could
accept in normal situations such that the load after failure is
Briscoe Expires September 6, 2006 [Page 8]
Internet-Draft Framework using Pre-Congestion Notification March 2006
expected to stay below acceptable levels even with reduced network
resources.
On the other hand, an operator could just rely for admission control
on the traffic conditioning agreements of the DiffServ architecture
[RFC2475]. The pre-emption mechanism described in this document would
be used to counteract the problem described at the end of Section
1.1.1.
1.2. Terminology
This terminology is copied from the pre-congestion notification
marking draft [PCN]:
o Pre-Congestion Notification (PCN): two new algorithms that
determine when a PCN-enabled router Admission Marks and Pre-
emption Marks a packet, depending on the traffic level.
o Admission Marking condition: the traffic level is such that the
router Admission Marks packets. The router provides an "early
warning" that the load is nearing the engineered admission control
capacity, before there is any significant build-up of CL packets
in the queue.
o Pre-emption Marking condition: the traffic level is such that the
router Pre-emption Marks packets. The router warns explicitly that
pre-emption may be needed.
o Configured-admission-rate: the reference rate used by the
admission marking algorithm in a PCN-enabled router.
o Configured-pre-emption-rate - the reference rate used by the pre-
emption marking algorithm in a PCN-enabled router.
The following terms are defined here:
o Ingress gateway: node at an ingress to the CL-region. A CL-region
may have several ingress gateways.
o Egress gateway: node at an egress from the CL-region. A CL-region
may have several egress gateways.
Briscoe Expires September 6, 2006 [Page 9]
Internet-Draft Framework using Pre-Congestion Notification March 2006
o Interior node: a node which is part of the CL-region, but isn't an
ingress or egress node.
o CL-region: A region of the Internet in which all traffic
enters/leaves through an ingress/egress gateway and all nodes run
Pre-Congestion Notification marking. A CL-region is a DiffServ
region (a DiffServ region is either a single DiffServ domain or
set of contiguous DiffServ domains), but note that the CL-region
does not use the traffic conditioning agreements (TCAs) of the
(informational) DiffServ architecture.
o CL-region-aggregate: all the microflows between a specific pair of
ingress and egress gateways. Note there is no identifier unique to
the aggregate.
o Congestion-Level-Estimate: the number of bits in CL packets that
are admission marked, divided by the number of bits in all CL
packets. It is calculated as an exponentially weighted moving
average. It is calculated by an egress gateway for the CL packets
from a particular ingress gateway, i.e. there is a Congestion-
Level-Estimate for each CL-region-aggregate.
o Sustainable-Aggregate-Rate: the rate of traffic that the network
can actually support for a specific CL-region-aggregate. So it is
measured by an egress gateway for the CL packets from a particular
ingress gateway.
1.3. Existing terminology
This is a placeholder for useful terminology that is defined
elsewhere.
1.4. Standardisation requirements
The framework described in this document has two new standardisation
requirements:
o new Pre-Congestion Notification for Admission Marking and Pre-
emption Marking are required, as detailed in [PCN].
Briscoe Expires September 6, 2006 [Page 10]
Internet-Draft Framework using Pre-Congestion Notification March 2006
o the end-to-end signalling protocol needs to be modified to carry
the Congestion-Level-Estimate report (for admission control) and
the Sustainable-Aggregate-Rate (for flow pre-emption). With our
assumption of RSVP (Section 2.2) as the end-to-end signalling
protocol, it means that extensions to RSVP are required, as
detailed in [RSVP-ECN], for example to carry the Congestion-Level-
Estimate and Sustainable-Aggregate-Rate information from egress
gateway to ingress gateway.
Other than these things, the arrangement uses existing IETF protocols
throughout, although not in their usual architecture.
1.5. Structure of rest of the document
Section 2 describes some key aspects of the framework: our goals,
assumptions and the benefits we believe it has. Section 3 describes
the architecture (including a use case), whilst Section 4 summarises
the required changes to the various nodes in the CL-region. Section 5
outlines some possible extensions. Section 6 provides some comparison
with existing QoS mechanisms.
Briscoe Expires September 6, 2006 [Page 11]
Internet-Draft Framework using Pre-Congestion Notification March 2006
2. Key aspects of the framework
In this section we discuss the key aspects of the framework:
o At a high level, our key goals, i.e. the functionality that we
want to achieve
o The assumptions that we're prepared to make
o The consequent benefits they bring
2.1. Key goals
The framework achieves an end-to-end controlled load (CL) service
where a segment of the end-to-end path is an edge-to-edge Pre-
Congestion Notification region. CL is a quality of service (QoS)
closely approximating the QoS that the same flow would receive from a
lightly loaded network element [RFC2211]. It is useful for inelastic
flows such as those for real-time media.
o The CL service should be achieved despite varying load levels of
other sorts of traffic, which may or may not be rate adaptive
(i.e. responsive to packet drops or ECN marks).
o The CL service should be supported for a variety of possible CL
sources: Constant Bit Rate (CBR), Variable Bit Rate (VBR) and
voice with silence suppression. VBR is the most challenging to
support.
o After a localised failure in the interior of the CL-region causing
heavy congestion, the CL service should recover gracefully by pre-
empting (dropping) some of the admitted CL microflows, whilst
preserving as many of them as possible with their full CL QoS.
o It is suggested that flow pre-emption needs to be completed within
1-2 seconds, because it is estimated that after a few seconds then
many affected users will start to hang up (and then not only is a
flow pre-emption mechanism redundant and possibly even counter-
productive, but also many more flows than necessary to reduce
congestion may hang up). Also, other, lower priority traffic
classes will not be restored to partial service until the higher
priority CL service reduces its load on shared links.
Briscoe Expires September 6, 2006 [Page 12]
Internet-Draft Framework using Pre-Congestion Notification March 2006
o The CL service should support emergency services ([EMERG-RQTS],
[EMERG-TEL]) as well as the Assured Service which is the IP
implementation of the existing ITU-T/NATO/DoD telephone system
architecture known as Multi-Level Pre-emption and Precedence
[ITU.MLPP.1990] [ANSI.MLPP.Spec][ANSI.MLPP.Supplement], or MLPP.
In particular, this involves admitting new high priority sessions
even when admission control thresholds are reached and new routine
sessions are rejected. Similarly, this involves taking into
account session priorities and properties at the time of pre-
empting flows.
2.2. Key assumptions
The framework does not try to deliver the above functionality in all
scenarios. We make the following assumptions about the type of
scenario to be solved.
o Edge-to-edge: all the nodes in the CL-region are upgraded with
Pre-Congestion Notification, and all the ingress and egress
gateways are upgraded to perform the measurement-based admission
control and flow pre-emption. Note that although the upgrades
required are edge-to-edge, the CL service is provided end-to-end.
o Additional load: we assume that any additional load offered within
the reaction time of the admission control mechanism doesn't move
the CL-region directly from no congestion to overload. So it
assumes there will always be an intermediate stage where some CL
packets are Admission Marked, but they are still delivered without
significant QoS degradation. We believe this is valid for core and
backbone networks with typical call arrival patterns (given the
reaction time is little more than one round trip time across the
CL-region), but is unlikely to be valid in access networks where
the granularity of an individual call becomes significant.
o Aggregation: we assume that in normal operations, there are many
CL microflows within the CL-region, typically at least hundreds
between any pair of ingress and egress gateways. The implication
is that the solution is targeted at core and backbone networks and
possibly parts of large access networks.
o Trust: we assume that there is trust between all the nodes in the
CL-region. For example, this trust model is satisfied if one
operator runs the whole of the CL-region. But we make no such
assumptions about the end nodes, i.e. depending on the scenario
they may be trusted or untrusted by the CL-region.
Briscoe Expires September 6, 2006 [Page 13]
Internet-Draft Framework using Pre-Congestion Notification March 2006
o Signalling: we assume that the end-to-end signalling protocol is
RSVP. Section 3 describes how the CL-region fits into such an end-
to-end QoS scenario, whilst [RSVP-ECN] describes the extensions to
RSVP that are required.
o Separation: we assume that all nodes within the CL-region are
upgraded with the CL mechanism, so the requirements of [Floyd] are
met because the CL-region is an enclosed environment. Also, an
operator separates CL-traffic in the CL-region from outside
traffic by administrative configuration of the ring of gateways
around the region. Within the CL-region we assume that the CL-
traffic is separated from non-CL traffic.
o Routing: we assume that one of the following applies:
(same path) all packets between a pair of ingress and egress
gateways follow the same path. This ensures that the Congestion-
Level-Estimate used in the admission control procedure reflects
the status of the path followed by the new flow's packets
(load balanced) packets between a pair of ingress and egress
gateways follow different paths but that the load balancing
scheme is tuned in the CL-region to distribute load such that
the different paths always receive comparable relative load.
This ensures that the Congestion-Level-Estimate used in the
admission control procedure (and which is computed taking into
account packets travelling on all the paths) also approximately
reflects the status of the actual path followed by the new
microflow's packets
(worst case assumed) packets between a pair of ingress and
egress gateways follow different paths but that (i) it is
acceptable for the operator to keep the CL traffic between this
pair of gateways to a level dictated by the most loaded of all
paths between this pair of gateways (so that CL flows may be
rejected - or even pre-empted in some situations - even if one
or more of the paths between the pair of gateways is operating
below its engineered levels) and that (ii) it is acceptable for
that operator to configure engineered levels below optimum
levels to compensate for the fact that the effect on the
Congestion-Level-Estimate of the congestion experienced over one
of the paths may be diluted by traffic received over non-
congested paths so that lower thresholds need to be used in
these cases to ensure early admission control rejection and pre-
emption over the congested paths.
Briscoe Expires September 6, 2006 [Page 14]
Internet-Draft Framework using Pre-Congestion Notification March 2006
We are investigating ways of loosening the restrictions set by some
of these assumptions, for instance:
o Trust: to allow the CL-region to span multiple, non-trusting
operators, using the technique of [Re-PCN] and mentioned in
Section 5.1.
o Signalling: we believe that the solution could operate with
another signalling protocol such as NSIS. It could also work with
application level signalling as suggested in [RT-ECN].
o Additional load: we believe that the assumption is valid for core
and backbone networks, with an appropriate margin between the
configured-admission-rate and the capacity for CL traffic.
However, in principle a burst of admission requests can occur in a
short time. We expect this to be a rare event under normal
conditions, but it could happen e.g. due to a 'flash crowd'. If it
does, then more flows may be admitted than should be, triggering
the pre-emption mechanisms. There are various approaches to how an
operator might try to alleviate this issue, which are discussed in
the 'Flash crowds' section 5.1 later.
o Separation: the assumption that CL traffic is separated from non-
CL traffic implies that the CL traffic has its own PHB, not shared
with other traffic. We are looking at whether it could share
Expedited Forwarding's PHB, but supplemented with Pre-Congestion
Notification. If this is possible, other PHBs (like Assured
Forwarding) could be supplemented with the same new behaviours.
This is similar to how RFC3168 ECN was defined to supplement any
PHB.
o Routing: we are looking in greater detail at the solution in the
presence of Equal Cost Multi-Path routing and at suitable
enhancements. See also the "Tunnelling" section later.
2.3. Key benefits
We believe that the mechanism described in this document has several
advantages:
Briscoe Expires September 6, 2006 [Page 15]
Internet-Draft Framework using Pre-Congestion Notification March 2006
o It achieves statistical guarantees of quality of service for
microflows, delivering a very low delay, jitter and packet loss
service suitable for applications like voice and video calls that
generate real time inelastic traffic. This is because of its per
microflow admission control scheme, combined with its dynamic on-
path "early warning" of potential congestion. The guarantee is at
least as strong as with IntServ Controlled Load (Section 6.1
mentions why the guarantee may be somewhat better), but without
the scalability problems of per-microflow IntServ.
o It can support "Emergency" and military Multi-Level Pre-emption
and Priority services, even in times of heavy congestion (perhaps
caused by failure of a node within the CL-region), by pre-empting
on-going "ordinary CL microflows". See also Section 4.5.
o It scales well, because there is no signal processing or path
state held by the interior nodes of the CL-region.
o It is resilient, again because no state is held by the interior
nodes of the CL-region. Hence during an interior routing change
caused by a node failure no microflow state has to be relocated.
The flow pre-emption mechanism further helps resilience because it
rapidly reduces the load to one that the CL-region can support.
o It helps preserve, through the flow pre-emption mechanism, QoS to
as many microflows as possible and to lower priority traffic in
times of heavy congestion (e.g. caused by failure of an interior
node). Otherwise long-lived microflows could cause loss on all CL
microflows for a long time.
o It avoids the potential catastrophic failure problem when the
DiffServ architecture is used in large networks using statically
provisioned capacity. This is achieved by controlling the load
dynamically, based on edge-to-edge-path real-time measurement of
Pre-Congestion Notification, as discussed in Section 1.1.1.
o It requires minimal new standardisation, because it reuses
existing QoS protocols and algorithms.
o It can be deployed incrementally, region by region or network by
network. Not all the regions or networks on the end-to-end path
need to have it deployed. Two CL-regions can even be separated by
a network that uses another QoS mechanism (e.g. MPLS-TE).
Briscoe Expires September 6, 2006 [Page 16]
Internet-Draft Framework using Pre-Congestion Notification March 2006
o It provides a deployment path for use of ECN for real-time
applications. Operators can gain experience of ECN before its
applicability to end-systems is understood and end terminals are
ECN capable.
Briscoe Expires September 6, 2006 [Page 17]
Internet-Draft Framework using Pre-Congestion Notification March 2006
3. Architecture
3.1. Admission control
In this section we describe the admission control mechanism. We
discuss the three pieces of the solution and then give an example of
how they fit together in a use case:
o the new Pre-Congestion Notification for Admission Marking used by
all nodes in the CL-region
o how the measurements made support our admission control mechanism
o how the edge to edge mechanism fits into the end to end RSVP
signalling
3.1.1. Pre-Congestion Notification for Admission Marking
This is discussed in [PCN]. Here we only give a brief outline.
To support our admission control mechanism, each node in the CL-
region runs an algorithm to determine whether to set the packet into
the Admission Marked state. The algorithm measures the aggregate CL
traffic on the link and ensures that packets are admission marked
before the actual queue builds up, but when it is in danger of doing
so soon; the probability of admission marking increases with the
danger. The algorithm's main parameter is the configured-admission-
rate, which is set lower than the link speed, perhaps considerably
so. Admission marked packets indicate that the CL traffic rate is
reaching the configured-admission-rate and so act as an "early
warning" that the engineered capacity is nearly reached. Therefore
they indicate that requests to admit prospective new CL flows may
need to be refused.
3.1.2. Measurements to support admission control
To support our admission control mechanism the egress measures the
Congestion-Level-Estimate for traffic from each remote ingress
gateway, i.e. per CL-region-aggregate. The Congestion-Level-Estimate
is the number of bits in CL packets that are admission marked,
divided by the number of bits in all CL packets. It is calculated as
an exponentially weighted moving average. It is calculated by an
egress node separately for the CL packets from each particular
Briscoe Expires September 6, 2006 [Page 18]
Internet-Draft Framework using Pre-Congestion Notification March 2006
ingress node. This Congestion-Level-Estimate provides an estimate of
how near the links on the path inside the CL-region are getting to
the configured-admission-rate. Note that the metering is done
separately per ingress node, because there may be sufficient capacity
on all the nodes on the path between one ingress gateway and a
particular egress, but not from a second ingress to that same egress
gateway.
3.1.3. How edge-to-edge admission control supports end-to-end QoS
signalling
Consider a scenario that consists of two end hosts, each connected to
their own access networks, which are linked by the CL-region. A
source tries to set up a new CL microflow by sending an RSVP PATH
message, and the receiving end host replies with an RSVP RESV
message. Outside the CL-region some other method, for instance
IntServ, is used to provide QoS. From the perspective of RSVP the CL-
region is a single hop, so the RSVP PATH and RESV messages are
processed by the ingress and egress gateways but are carried
transparently across all the interior nodes; hence, the ingress and
egress gateways hold per microflow state, whilst no state is kept by
the interior nodes. So far this is as in IntServ over DiffServ
[RFC2998]. However, in order to support our admission control
mechanism, the egress gateway adds to the RESV message an opaque
object which states the current Congestion-Level-Estimate for the
relevant CL-region-aggregate. Details of the corresponding RSVP
extensions are described in [RSVP-ECN].
3.1.4. Use case
To see how the three pieces of the solution fit together, we imagine
a scenario where some microflows are already in place between a given
pair of ingress and egress gateways, but the traffic load is such
that no packets from these flows are admission marked as they travel
across the CL-region. A source wanting to start a new CL microflow
sends an RSVP PATH message. The egress gateway adds an object to the
RESV message with the Congestion-Level-Estimate, which is zero. The
ingress gateway sees this and consequently admits the new flow. It
then forwards the RSVP RESV message upstream towards the source end
host. Hence, assuming there's sufficient capacity in the access
networks, the new microflow is admitted end-to-end.
The source now sends CL packets, which arrive at the ingress gateway.
The ingress uses a five-tuple filter to identify that the packets are
part of a previously admitted CL microflow, and it also polices the
microflow to ensure it remains within its traffic profile. (The
ingress has learnt the required information from the RSVP messages.)
Briscoe Expires September 6, 2006 [Page 19]
Internet-Draft Framework using Pre-Congestion Notification March 2006
When forwarding a packet belonging to an admitted microflow, the
ingress sets the packet's DSCP and ECN fields to the appropriate
values configured for the CL region. The CL packet now travels across
the CL-region, getting admission marked if necessary.
Next, we imagine the same scenario but at a later time when load is
higher at one (or more) of the interior nodes, which start to set CL
packets into the Admission Marked state, because their load on the
outgoing link is nearing the configured-admission-rate. The next time
a source tries to set up a CL microflow, the ingress gateway learns
(from the egress) the relevant Congestion-Level-Estimate. If it is
greater than some CLE-threshold value then the ingress refuses the
request, otherwise it is accepted.
It is also possible for an egress gateway to get a RSVP RESV message
and not know what the Congestion-Level-Estimate is. For example, if
there are no CL microflows at present between the relevant ingress
and egress gateways. In this case the egress requests the ingress to
send probe packets, from which it can initialise its meter. RSVP
Extensions for such a request to send probe data can be found in
[RSVP-ECN].
3.2. Flow pre-emption
In this section we describe the flow pre-emption mechanism. We
discuss the two parts of the solution and then give an example of how
they fit together in a use case:
o How an ingress gateway is triggered to test whether flow pre-
emption may be needed
o How an ingress gateway determines the right amount of CL traffic
to drop
The mechanism is defined in [PCN] and [RSVP-ECN].
3.2.1. Alerting an ingress gateway that flow pre-emption may be needed
Alerting an ingress gateway that flow pre-emption may be needed is a
two stage process: a router in the CL-region alerts an egress gateway
that flow pre-emption may be needed; in turn the egress gateway
alerts the relevant ingress gateway. Every router in the CL-region
Briscoe Expires September 6, 2006 [Page 20]
Internet-Draft Framework using Pre-Congestion Notification March 2006
has the ability to alert egress gateways, which may be done either
explicitly or implicitly:
o Explicit - the router per-hop behaviour is supplemented with a new
Pre-emption Marking behaviour, which is outlined below. Reception
of such a packet by the egress gateway alerts it that pre-emption
may be needed.
o Implicit - the router behaviour is unchanged from the Admission
Marking behaviour described earlier. The egress gateway treats a
Congestion-Level-Estimate of (almost) 100% as an implicit alert
that pre-emption may be required. ('Almost' because the
Congestion-Level-Estimate is a moving average, so can never reach
exactly 100%.)
To support explicit pre-emption alerting, each node in the CL-region
runs an algorithm to determine whether to set the packet into the
Pre-emption Marked state. The algorithm measures the aggregate CL
traffic and ensures that packets are pre-emption marked before the
actual queue builds up. The algorithm's main parameter is the
configured-pre-emption-rate, which is set lower than the link speed
(but higher than the configured-admission-rate). Thus pre-emption
marked packets indicate that the CL traffic rate is reaching the
configured-pre-emption-rate and so act as an "early warning" that the
engineered capacity is nearly reached. Therefore they indicate that
it may be advisable to pre-empt some of the existing CL flows in
order to preserve the QoS of the others.
Note that the explicit mechanism only makes sense if all the routers
in the CL-region have the functionality so that the egress gateways
can rely on the explicit mechanism. Otherwise there is the danger
that the traffic happens to focus on a router without it, and egress
gateways then have also to watch for implicit pre-emption alerts.
When one or more packets in a CL-region-aggregate alert the egress
gateway of the need for flow pre-emption, whether explicitly or
implicitly, the egress puts that CL-region-aggregate into the Pre-
emption Alert state. For each CL-region-aggregate in alert state it
measures the rate of traffic at the egress gateway (i.e. the traffic
rate of the appropriate CL-region-aggregate) and reports this to the
relevant ingress gateway. The steps are:
Briscoe Expires September 6, 2006 [Page 21]
Internet-Draft Framework using Pre-Congestion Notification March 2006
o Determine the relevant ingress gateway - for the explicit case the
egress gateway examines the pre-emption marked packet and uses the
state installed at the time of admission to determine which
ingress gateway the packet came from. For the implicit case the
egress gateway has already determined this information, because
the Congestion-Level-Estimate is calculated per ingress gateway.
o Measure the traffic rate of CL packets - as soon as the egress
gateway is alerted (whether explicitly or implicitly) it measures
the rate of CL traffic from this ingress gateway (i.e. for this
CL-region-aggregate). Note that pre-emption marked packets are
excluded from that measurement. It should make its measurement
quickly and accurately, but exactly how is up to the
implementation.
o Alert the ingress gateway - the egress gateway then immediately
alerts the relevant ingress gateway about the fact that flow pre-
emption may be required. This Alert message also includes the
measured Sustainable-Aggregate-Rate, i.e. the egress rate of CL-
traffic for this ingress gateway. The Alert message is sent using
reliable delivery. Procedures for support of such an Alert using
RSVP are defined in [RSVP-ECN].
_ _
-------------- / \ -----------------
CL packet |Update | / Is it a \ Y | Measure CL rate |
arrives --->|Congestion- |--->/pre-emption\-----> | from ingress and|
|Level-Estimate| \ marked / | alert ingress |
-------------- \ packet? / -----------------
\_ _/
Figure 2: Egress gateway action for explicit Pre-emption Alert
_ _
-------------- / \ -----------------
CL packet |Update | / Is \ Y | Measure CL rate |
arrives --->|Congestion- |--->/ C.L.E. \-----> | from ingress and|
|Level-Estimate| \ (nearly) / | alert ingress |
-------------- \ 100%? / -----------------
\_ _/
Figure 3: Egress gateway action for implicit Pre-emption Alert
Briscoe Expires September 6, 2006 [Page 22]
Internet-Draft Framework using Pre-Congestion Notification March 2006
3.2.2. Determining the right amount of CL traffic to drop
The method relies on the insight that the amount of CL traffic that
can be supported between a particular pair of ingress and egress
gateways, is the amount of CL traffic that is actually getting across
the CL-region to the egress gateway without being re-marked to the
Pre-emption Marked state. Hence we term it the Sustainable-Aggregate-
Rate.
So when the ingress gateway gets the Alert message from an egress
gateway, it compares:
o The traffic rate that it is sending to this particular egress
gateway (which we term ingress-aggregate-rate)
o The traffic rate that the egress gateway reports (in the Alert
message) that it is receiving from this ingress gateway (which is
the Sustainable-Aggregate-Rate)
If the difference is significant, then the ingress gateway pre-empts
some microflows. It only pre-empts if:
Ingress-aggregate-rate > Sustainable-Aggregate-Rate + error
The "error" term is partly to allow for inaccuracies in the
measurements of the rates. It is also needed because the ingress-
aggregate-rate is measured at a slightly later moment than the
Sustainable-Aggregate-Rate, and it is quite possible that the
ingress-aggregate-rate has increased in the interim due to natural
variation of the bit rate of the CL sources. So the "error" term
allows for some variation in the ingress rate without triggering pre-
emption.
The ingress gateway should pre-empt enough microflows to ensure that:
New ingress-aggregate-rate < Sustainable-Aggregate-Rate - error
The "error" term here is used for similar reasons but in the other
direction, to ensure slightly more load is shed than seems necessary,
in case the two measurements were taken during a short-term fall in
load.
When the routers in the CL-region are using explicit pre-emption
alerting, the ingress gateway would normally pre-empt microflows
whenever it gets an alert (it always would if it were possible to set
Briscoe Expires September 6, 2006 [Page 23]
Internet-Draft Framework using Pre-Congestion Notification March 2006
"error" equal to zero). For the implicit case however this is not so.
It receives an Alert message when the Congestion-Level-Estimate
reaches (almost) 100%, which is roughly when traffic exceeds the
configured-admission-rate. However, it is only when packets are
indeed dropped en route that the Sustainable-Aggregate-Rate becomes
less than the ingress-aggregate-rate so only then will pre-emption
will actually occur on the ingress router.
Hence with the implicit scheme, pre-emption can only be triggered
once the system starts dropping packets and thus the QoS of flows
starts being significantly degraded. This is in contrast with the
explicit scheme which allows flow pre-emption to be triggered before
any packet drop, simply when the traffic reaches the configured-pre-
emption-rate. Therefore we believe that the explicit mechanism is
superior. However it does require new functionality on all the
routers (although this is little more than a bulk token bucket - see
[PCN] for details).
3.2.3. Use case for flow pre-emption
To see how the pieces of the solution fit together in a use case, we
imagine a scenario where many microflows have already been admitted.
We confine our description to the explicit pre-emption mechanism. Now
an interior router in the CL-region fails. The network layer routing
protocol re-routes round the problem, but as a consequence traffic on
other links increases. In fact let's assume the traffic on one link
now exceeds its configured-pre-emption-rate and so the router pre-
emption marks CL packets. When the egress sees the first one of the
pre-emption marked packets it immediately determines which microflow
this packet is part of (by using a five-tuple filter and comparing it
with state installed at admission) and hence which ingress gateway
the packet came from. It sets up a meter to measure the traffic rate
from this ingress gateway, and as soon as possible sends a message to
the ingress gateway. This message alerts the ingress gateway that
pre-emption may be needed and contains the traffic rate measured by
the egress gateway. Then the ingress gateway determines the traffic
rate that it is sending towards this egress gateway and hence it can
calculate the amount of traffic that needs to be pre-empted.
The ingress gateway could now just shed random microflows, but it is
better if the least important ones are dropped. The ingress gateway
could use information stored locally in each reservation's state
(such as for example the RSVP pre-emption priority) as well as
information provided by a policy decision point in order to decide
which of the flows to shed (or perhaps which ones not to shed). The
Briscoe Expires September 6, 2006 [Page 24]
Internet-Draft Framework using Pre-Congestion Notification March 2006
ingress gateway then initiates RSVP signalling to instruct the
relevant destinations that their session has been terminated, and to
tell (RSVP) nodes along the path to tear down associated RSVP state.
To guard against recalcitrant sources, normal IntServ policing will
block any future traffic from the dropped flows from entering the CL-
region. Note that - with the explicit Pre-emption Alert mechanism -
since the configured-pre-emption-rate may be significantly less than
the physical line capacity, flow pre-emption may be triggered before
any congestion has actually occurred and before any packet is
dropped.
We extend the scenario further by imagining that (due to a disaster
of some kind) further routers in the CL-region fail during the time
taken by the pre-emption process described above. This is handled
naturally, as packets will continue to be pre-emption marked and so
the pre-emption process will happen for a second time.
Flow pre-emption also helps emergency/military calls by taking into
account the corresponding call priorities when selecting calls to be
pre-empted, which is likely to be particularly important in a
disaster scenario.
Briscoe Expires September 6, 2006 [Page 25]
Internet-Draft Framework using Pre-Congestion Notification March 2006
4. Details
This section is intended to provide a systematic summary of the new
functionality required by the routers in the CL-region.
A network operator upgrades normal IP routers by:
o Adding functionality related to admission control and flow pre-
emption to all its ingress and egress gateways
o Adding Pre-Congestion Notification for Admission and Pre-emption
Marking to all the nodes in the CL-region.
We consider the detailed actions required for each of the types of
node in turn.
4.1. Ingress gateways
Ingress gateways perform the following tasks:
o Classify incoming packets - decide whether they are CL or non-CL
packets. This is done using an IntServ filter spec (source and
destination addresses and port numbers), whose details have been
gathered from the RSVP messaging.
o Police - check that the microflow conforms with what has been
agreed (i.e. it keeps to its agreed data rate). If necessary,
packets which do not correspond to any reservations, packets which
are in excess of the rate agreed for their reservation, and
packets for a reservation that has earlier been pre-empted may be
policed. Policing may be achieved via dropping or via re-marking
of the packet's DSCP to a value different from the CL behaviour
aggregate.
o Packet ECN colouring - for CL microflows, set the ECN field
appropriately (see [PCN] for some discussion of encoding)
o Perform 'interior node' functions (see next sub-section)
o Admission Control - on new session establishment, consider the
Congestion-Level-Estimate received from the corresponding egress
gateway and most likely based on a simple configured CLE-threshold
decide if a new call is to be admitted or rejected (taking into
account local policy information as well as optionally information
provided by a policy decision point).
Briscoe Expires September 6, 2006 [Page 26]
Internet-Draft Framework using Pre-Congestion Notification March 2006
o Probe - if requested by the egress gateway to do so, the ingress
gateway generates probe traffic so that the egress gateway can
compute the Congestion-Level-Estimate from this ingress gateway.
Probe packets may be simple data addressed to the egress gateway
and require no protocol standardisation, although there will be
best practice for their number, size and rate.
o Measure - when it receives an Alert message from an egress
gateway, it determines the rate at which it is sending packets to
that egress gateway
o Pre-empt - calculate how much CL traffic needs to be pre-empted;
decide which microflows should be dropped, perhaps in consultation
with a Policy Decision Point; and do the necessary signalling to
drop them.
4.2. Interior nodes
Interior nodes do the following tasks:
o Classify packets - examine the DSCP and ECN field to see if it's a
CL packet
o Non-CL packets are handled as usual, with respect to dropping them
or setting their CE codepoint.
o Pre-Congestion Notification - CL packets are Admission Marked and
Pre-emption Marked according to the algorithm detailed in [PCN]
and outlined in Section 3.
4.3. Egress gateways
Egress gateways do the following tasks:
o Classify packets - determine which ingress gateway a CL packet has
come from. This is the previous RSVP hop, hence the necessary
details are obtained just as with IntServ from the state
associated with the packet five-tuple, which has been built using
information from the RSVP messages.
Briscoe Expires September 6, 2006 [Page 27]
Internet-Draft Framework using Pre-Congestion Notification March 2006
o Meter - for CL packets, calculate the fraction of the total number
of bits which are in Admission marked packets. The calculation is
done as an exponentially weighted moving average (see Appendix). A
separate calculation is made for CL packets from each ingress
gateway. The meter works on an aggregate basis and not per
microflow.
o Signal the Congestion-Level-Estimate - this is piggy-backed on the
reservation reply. An egress gateway's interface is configured to
know it is an egress gateway, so it always appends this to the
RESV message. If the Congestion-Level-Estimate is unknown or is
too stale, then the egress gateway can request the ingress gateway
to send probes.
o Packet colouring - for CL packets, set the DSCP and the ECN field
to whatever has been agreed as appropriate for the next domain. By
default the ECN field is set to the Not-ECT codepoint. See also
the discussion in the Tunnelling section later.
o Measure the rate - measure the rate of CL traffic from a
particular ingress gateway (i.e. the rate for the CL-region-
aggregate), when alerted (either explicitly or implicitly) that
pre-emption may be required. The measured rate is reported back to
the appropriate ingress gateway [RSVP-ECN].
4.4. Failures
If an interior node fails, then the regular IP routing protocol will
re-route round it. If the new route can carry all the admitted
traffic, flows will gracefully continue. If instead this causes early
warning of congestion from the new route, then admission control
based on pre-congestion notification will ensure new flows will not
be admitted until enough existing flows have departed. Finally re-
routing may result in heavy congestion, when the pre-emption
mechanism will kick in.
If a gateway fails then we would like regular RSVP procedures
[RFC2205] to take care of things. With the local repair mechanism of
[RFC2205], when a route changes the next RSVP PATH refresh message
will establish path state along the new route, and thus attempt to
re-establish reservations through the new ingress gateway.
Essentially the same procedure is used as described earlier in this
document, with the re-routed session treated as a new session
request.
In more detail, consider what happens if an ingress gateway of the
CL-region fails. Then RSVP routers upstream of it do IP re-routing to
Briscoe Expires September 6, 2006 [Page 28]
Internet-Draft Framework using Pre-Congestion Notification March 2006
a new ingress gateway. The next time the upstream RSVP router sends a
PATH refresh message it reaches the new ingress gateway which
therefore installs the associated RSVP state. The next RSVP RESV
refresh will pick up the congestion-level-estimate from the egress
gateway, and the ingress compares this with its threshold to decide
whether to admit the new session. This could result in some of the
flows being rejected, but those accepted will receive the full QoS.
An issue with this is that we have to wait until a PATH and RESV
refresh messages are sent - which may not be very often - the default
value is 30 seconds. [RFC2205] discusses how to speed up the local
repair mechanism. First, the RSVP module is notified by the local
routing protocol module of a route change to particular destinations,
which triggers it to rapidly send out PATH refresh messages. Further,
when a PATH refresh arrives with a previous hop address different
from the one stored, then RESV refreshes are immediately sent to that
previous hop. Where RSVP is operating hop-by-hop, ie on every router,
then triggering the PATH refresh is easy as the node can simply
monitor its local link. Thus, this fast local repair mechanism can be
used to deal with failures upstream of the ingress gateway, with
failures of the ingress gateway and with failures downstream of the
egress gateway.
But where RSVP is not operating hop-by-hop (as is the case within the
CL-region), it is not so easy to trigger the PATH refresh.
Unfortunately, this problem applies if an egress gateway fails, since
it's very likely that an egress gateway is several IP hops from the
ingress gateway. (If the ingress is several IP hops from its previous
RSVP node, then there is the same issue.) The options appear to be:
o the ingress gateway has a link state database for the CL-region,
so it can detect that an egress gateway has failed or became
unreachable
o there is an inter-gateway protocol, so the ingress can
continuously check that the egress gateways are still alive
o (default) do nothing and wait for the regular PATH/RESV refreshes
(and, if needed, the pre-emption mechanism) to sort things out.
4.5. Admission of 'emergency / higher precedence' session
Section 4.1 describes how if the Congestion-Level-Estimate is greater
than the CLE-threshold all new sessions are refused. But it is
Briscoe Expires September 6, 2006 [Page 29]
Internet-Draft Framework using Pre-Congestion Notification March 2006
unsatisfactory to block emergency calls, for instance. Therefore it
is recommended that an 'emergency / higher precedence' call is
admitted immediately even if the CLE-threshold is exceeded. Usually
the network can actually handle the additional microflow, because
there is a safety margin between the configured-admission-rate and
the configured-pre-emption-rate. Normal call termination behaviour
will soon bring the traffic level down below the configured-
admission-rate. However, in exceptional circumstances the 'emergency
/ higher precedence' call may cause the traffic level to exceed the
configured-pre-emption-rate; then the usual pre-emption mechanism
will pre-empt enough (non 'emergency / higher precedence' )
microflows to bring the total traffic back under the configured-pre-
emption-rate.
4.6. Tunnelling
It is possible to tunnel all CL packets across the CL-region.
Although there is a cost of tunnelling (additional header on each
packet, additional processing at tunnel ingress and egress), there
are three reasons it may be interesting.
ECMP:
If the CL-region uses Equal Cost Multipath Routing (ECMP), then
traffic between a particular pair of ingress and egress gateways may
follow several different paths.
Why? An ECMP-enabled router runs an algorithm to choose between
potential outgoing links, based on a hash of fields such as the
packet's source and destination addresses - exactly what depends on
the proprietary algorithm. Packets are addressed to the CL flow's
end-point, and therefore different flows may follow different paths
through the CL-region.
The problem is that if one of the paths is congested such that
packets are being admission marked, then the Congestion-Level-
Estimate measured by the egress gateway will be diluted by unmarked
packets from other non-congested paths. Similarly, the measurement of
the Sustainable-Aggregate-Rate will also be diluted.
One solution is to tunnel across the CL-region. Then the destination
address (and so on) seen by the ECMP algorithm is that of the egress
gateway, so all flows follow the same path.
Ingress gateway determination:
Briscoe Expires September 6, 2006 [Page 30]
Internet-Draft Framework using Pre-Congestion Notification March 2006
If packets are tunnelled from ingress gateway to egress gateway, the
egress gateway can very easily determine in the datapath which
ingress gateway a packet comes from (by simply looking at the source
address of the tunnel header). This can facilitate operations such as
computing the Congestion-Level-Estimate on a per ingress gateway
basis.
End-to-end ECN:
The ECN field is used for PCN marking (see [PCN] for details), and so
it needs to be re-set by the egress gateway to whatever has been
agreed as appropriate for the next domain. Therefore if a packet
arrives at the ingress gateway with its ECN field already set (ie not
'00'), it may leave the egress gateway with a different value. Hence
the end-to-end meaning of the ECN field is lost.
It is open to debate whether end-to-end congestion control is ever
necessary within an end-to-end reservation. But if a genuine need is
identified for end-to-end ECN semantics within a reservation, then
one solution is to tunnel CL packets across the CL-region. When the
egress gateway decapsulates them the original ECN field is recovered.
Briscoe Expires September 6, 2006 [Page 31]
Internet-Draft Framework using Pre-Congestion Notification March 2006
5. Potential future extensions
5.1. Mechanisms to deal with 'Flash crowds'
There is a time lag between the admission control decision (which
depends on the Congestion-Level-Estimate during RSVP signalling
during call set-up) and when the data is actually sent (after the
called party has answered). In PSTN terms this is the time the phone
rings. Normally the time lag doesn't matter much because (1) in the
CL-region there are many flows and they terminate and are answered at
roughly the same rate, and (2) the network can still operate safely
when the traffic level is some margin above the configured-admission-
rate.
A 'flash crowd' occurs when something causes many calls to be
initiated in a short period of time - for instance a 'televote'. So
there is a danger that a 'flash' of calls is accepted, but when the
calls are answered and data flows the traffic overloads the network.
There are various possible ways an operator could try to address the
problem.
The simplest option is to do nothing; an operator relies on the pre-
emption mechanism if there is a problem. This doesn't seem a good
choice, as 'flash crowds' are reasonably common on the PSTN, unless
the operator can ensure that nearly all "flash crowd" events are
blocked in the access network and so do not impact on the CL-region.
A second option is to send 'dummy data' as soon as the call is
admitted, thus effectively reserving the bandwidth whilst waiting for
the called party to answer. Reserving bandwidth in advance means that
the network cannot admit as many calls. For example, suppose sessions
last 100 seconds and ringing for 10 seconds, the cost is a 10% loss
of capacity. It may be possible to offset this somewhat by increasing
the configured-admission-rate in the routers, but it would need
further investigation.
A concern with this 'dummy data' option is that it may allow an
attacker to initiate many calls that are never answered (by a
cooperating attacker), so eventually the network would only be
carrying 'dummy data'. The attack exploits that charging only starts
when the call is answered and not when it is dialled. It may be
possible to alleviate the attack at the session layer - for example,
when the ingress gateway gets an RSVP PATH message it checks that the
source has been well-behaved recently.
A third option is that the egress gateway limits the rate at which it
sends out the Congestion-Level-Estimate, or limits the rate at which
Briscoe Expires September 6, 2006 [Page 32]
Internet-Draft Framework using Pre-Congestion Notification March 2006
calls are accepted by replying with a Congestion-Level-Estimate of
100% (this is the equivalent of 'call gapping' in the PSTN). There is
a trade-off, which would need to be investigated further, between the
degree of protection and possible adverse side-effects like slowing
down call set-up.
A final option is to re-perform admission control before the call is
answered. The ingress gateway monitors Congestion-Level-Estimate
updates received from each egress. If it notices that a Congestion-
Level-Estimate has risen above the CLE-threshold, then it terminates
all unanswered calls through that egress (eg by instructing the
session protocol to stop the 'ringing tone'). For extra safety the
Congestion-Level-Estimate could be re-checked when the call is
answered. A potential drawback for an operator that wants to emulate
the PSTN is that the PSTN network never drops a 'ringing' PSTN call.
5.2. Multi-domain and multi-operator usage
This potential extension would eliminate the trust assumption
(Section 2.2), so that the CL-region could consist of multiple
domains run by different operators that did not trust each other.
Then only the ingress and egress gateways of the CL-region would take
part in the admission control procedure, i.e. at the ingress to the
first domain and the egress from the final domain. The border routers
between operators within the CL-region would only have to do bulk
accounting - they wouldn't do per microflow metering and policing,
and they wouldn't take part in signal processing or hold path state
[Briscoe]. [Re-feedback] explains how a downstream domain can police
that its upstream domain does not 'cheat' by admitting traffic when
the downstream path is over-congested. [Re-PCN] proposes how to
achieve this with the help of another recently proposed extension to
ECN, involving re-echoing ECN feedback [Re-ECN].
5.3. Adaptive bandwidth for the Controlled Load service
The admission control mechanism described in this document assumes
that each router has a fixed bandwidth allocated to CL flows. A
possible extension is that the bandwidth is flexible, depending on
the level of non-CL traffic. If a large share of the current load on
a path is CL, then more CL traffic can be admitted. And if the
greater share of the load is non-CL, then the admission threshold can
be proportionately lower. The approach re-arranges sharing between
classes to aim for economic efficiency, whatever the traffic load
Briscoe Expires September 6, 2006 [Page 33]
Internet-Draft Framework using Pre-Congestion Notification March 2006
matrix. It also deals with unforeseen changes to capacity during
failures better than configuring fixed engineered rates. Adaptive
bandwidth allocation can be achieved by changing the admission
marking behaviour, so that the probability of admission marking a
packet would now depend on the number of queued non-CL packets as
well as the size of the virtual queue. The adaptive bandwidth
approach would be supplemented by placing limits on the adaptation to
prevent starvation of the CL by other traffic classes and of other
classes by CL traffic.
5.4. Controlled Load service with end-to-end Pre-Congestion Notification
It may be possible to extend the framework to parts of the network
where there are only a low number of CL microflows, i.e. the
aggregation assumption (Section 2.2) doesn't hold. In the extreme it
may be possible to operate the framework end-to-end, i.e. between end
hosts. One potential method is to send probe packets to test whether
the network can support a prospective new CL microflow. The probe
packets would be sent at the same traffic rate as expected for the
actual microflow, but in order not to disturb existing CL traffic a
router would always schedule probe packets behind CL ones (compare
[Breslau00]); this implies they have a new DSCP. Otherwise the
routers would treat probe packets identically to CL packets. In order
to perform admission control quickly, in parts of the network where
there are only a few CL microflows, the Pre-Congestion marking
behaviour for probe packets would switch from admission marking no
packets to admission marking them all for only a minimal increase in
load.
5.5. MPLS-TE
It may be possible to extend the framework for admission control of
microflows into a set of MPLS-TE aggregates (Multi-protocol label
switching traffic engineering). However it would require that the
MPLS header could include the ECN field, which is not precluded by
RFC3270.
Briscoe Expires September 6, 2006 [Page 34]
Internet-Draft Framework using Pre-Congestion Notification March 2006
6. Relationship to other QoS mechanisms
6.1. IntServ Controlled Load
The CL mechanism delivers QoS similar to Integrated Services
controlled load, but rather better as queues are kept empty by
driving admission control from a bulk virtual queue on each interface
that can detect a rise in load before queues build, sometimes termed
a virtual queue [AVQ, vq]. It is also more robust to route changes.
6.2. Integrated services operation over DiffServ
Our approach to end-to-end QoS is similar to that described in
[RFC2998] for Integrated services operation over DiffServ networks.
Like [RFC2998], an IntServ class (CL in our case) is achieved end-to-
end, with a CL-region viewed as a single reservation hop in the total
end-to-end path. Interior routers of the CL-region do not process
flow signalling nor do they hold state. Unlike [RFC2998] we do not
require the end-to-end signalling mechanism to be RSVP, although it
can be.
Bearing in mind these differences, we can describe our architecture
in the terms of the options in [RFC2998]. The DiffServ network region
is RSVP-aware, but awareness is confined to (what [RFC2998] calls)
the "border routers" of the DiffServ region. We use explicit
admission control into this region, with static provisioning within
it. The ingress "border router" does per microflow policing and sets
the DSCP and ECN fields to indicate the packets are CL ones (i.e. we
use router marking rather than host marking).
6.3. Differentiated Services
The DiffServ architecture does not specify any way for devices
outside the domain to dynamically reserve resources or receive
indications of network resource availability. In practice, service
providers rely on subscription-time Service Level Agreements (SLAs)
that statically define the parameters of the traffic that will be
accepted from a customer. The CL mechanism allows dynamic reservation
of resources through the DiffServ domain and, with the potential
extension mentioned in Section 5.1, it can span multiple domains
without active policing mechanisms at the borders (unlike DiffServ).
Therefore we do not use the traffic conditioning agreements (TCAs) of
the (informational) DiffServ architecture [RFC2475].
[Johnson] compares admission control with a 'generously dimensioned'
DiffServ network as ways to achieve QoS. The former is recommended.
Briscoe Expires September 6, 2006 [Page 35]
Internet-Draft Framework using Pre-Congestion Notification March 2006
6.4. ECN
The marking behaviour described in this document complies with the
ECN aspects of the IP wire protocol RFC3168, but provides its own
edge-to-edge feedback instead of the TCP aspects of RFC3168. All
nodes within the CL-region are upgraded with the admission marking
and pre-emption marking of Pre-Congestion Notification, so the
requirements of [Floyd] are met because the CL-region is an enclosed
environment. The operator prevents traffic arriving at a node that
doesn't understand CL by administrative configuration of the ring of
gateways around the CL-region.
6.5. RTECN
Real-time ECN (RTECN) [RTECN, RTECN-usage] has a similar aim to this
document (to achieve a low delay, jitter and loss service suitable
for RT traffic) and a similar approach (per microflow admission
control combined with an "early warning" of potential congestion
through setting the CE codepoint). But it explores a different
architecture without the aggregation assumption: host-to-host rather
than edge-to-edge. We plan to document such a host-to-host framework
in a parallel draft to this one, and to describe if and how [PCN] can
work in this framework.
6.6. RMD
Resource Management in DiffServ (RMD) [RMD] is similar to this work,
in that it pushes complex classification, traffic conditioning and
admission control functions to the edge of a DiffServ domain and
simplifies the operation of the interior nodes. One of the RMD modes
uses measurement-based admission control, however it works
differently: each interior node measures the user traffic load in the
PHB traffic aggregate, and each interior node processes a local
RESERVE message and compares the requested resources with the
available resources (maximum allowed load minus current load).
Hence a difference is that the CL architecture described in this
document has been designed not to require interaction between
interior nodes and signalling, whereas in RMD all interior nodes are
QoS-NSLP aware. So our architecture involves less processing in
interior nodes, is more agnostic to signalling, requires fewer
changes to existing standards and therefore works with existing RSVP
as well as having the potential to work with future signalling
protocols like NSIS.
Briscoe Expires September 6, 2006 [Page 36]
Internet-Draft Framework using Pre-Congestion Notification March 2006
RMD introduced the concept of Severe Congestion handling. The pre-
emption mechanism described in the CL architecture has similar
objectives but relies on different mechanisms.
It is planned to work together with the authors of [RMD] and that the
next version of this draft and [PCN] will be co-authored with them.
6.7. RSVP Aggregation over MPLS-TE
Multi-protocol label switching traffic engineering (MPLS-TE) allows
scalable reservation of resources in the core for an aggregate of
many microflows. To achieve end-to-end reservations, admission
control and policing of microflows into the aggregate can be achieved
using techniques such as RSVP Aggregation over MPLS TE Tunnels as per
[AGGRE-TE]. However, in the case of inter-provider environments,
these techniques require that admission control and policing be
repeated at each trust boundary or that MPLS TE tunnels span multiple
domains.
7. Security Considerations
To protect against denial of service attacks, the ingress gateway of
the CL-region needs to police all CL packets and drop packets in
excess of the reservation. This is similar to operations with
existing IntServ behaviour.
For pre-emption, it is considered acceptable from a security
perspective that the ingress gateway can treat "emergency/military"
CL flows preferentially compared with "ordinary" CL flows. However,
in the rest of the CL-region they are not distinguished (nonetheless,
our proposed technique does not preclude the use of different DSCPs
at the packet level as well as different priorities at the flow
level.). Keeping emergency traffic indistinguishable at the packet
level minimises the opportunity for new security attacks. For
example, if instead a mechanism used different DSCPs for
"emergency/military" and "ordinary" packets, then an attacker could
specifically target the former in the data plane (perhaps for DoS or
for eavesdropping).
Further security aspects to be considered later.
Briscoe Expires September 6, 2006 [Page 37]
Internet-Draft Framework using Pre-Congestion Notification March 2006
8. Acknowledgements
The admission control mechanism evolved from the work led by Martin
Karsten on the Guaranteed Stream Provider developed in the M3I
project [GSPa, GSP-TR], which in turn was based on the theoretical
work of Gibbens and Kelly [DCAC]. Kennedy Cheng, Gabriele Corliano,
Carla Di Cairano-Gilfedder, Kashaf Khan, Peter Hovell, Arnaud Jacquet
and June Tay (BT) helped develop and evaluate this approach.
9. Comments solicited
Comments and questions are encouraged and very welcome. They can be
sent to the Transport Area Working Group's mailing list,
tsvwg@ietf.org, and/or to the authors.
10. Changes from earlier versions of the draft
The main changes are:
From -00 to -01
The whole of the Pre-emption mechanism is added.
There are several modifications to the admission control mechanism.
From -01 to -02
The pre-congestion notification algorithms for admission marking and
pre-emption marking are now described in [PCN].
There are new sub-sections in Section 4 on Failures, Admission of
'emergency / higher precedence' session, and Tunnelling; and a new
sub-section in Section 5 on Mechanisms to deal with 'Flash crowds'.
Briscoe Expires September 6, 2006 [Page 38]
Internet-Draft Framework using Pre-Congestion Notification March 2006
11. Appendices
11.1. Appendix A: Explicit Congestion Notification
This Appendix provides a brief summary of Explicit Congestion
Notification (ECN).
[RFC3168] specifies the incorporation of ECN to TCP and IP, including
ECN's use of two bits in the IP header. It specifies a method for
indicating incipient congestion to end-nodes (eg as in RED, Random
Early Detection), where the notification is through ECN marking
packets rather than dropping them.
ECN uses two bits in the IP header of both IPv4 and IPv6 packets:
0 1 2 3 4 5 6 7
+-----+-----+-----+-----+-----+-----+-----+-----+
| DS FIELD, DSCP | ECN FIELD |
+-----+-----+-----+-----+-----+-----+-----+-----+
DSCP: differentiated services codepoint
ECN: Explicit Congestion Notification
Figure A.1: The Differentiated Services and ECN Fields in IP.
The two bits of the ECN field have four ECN codepoints, '00' to '11':
+-----+-----+
| ECN FIELD |
+-----+-----+
ECT CE
0 0 Not-ECT
0 1 ECT(1)
1 0 ECT(0)
1 1 CE
Figure A.2: The ECN Field in IP.
The not-ECT codepoint '00' indicates a packet that is not using ECN.
The CE codepoint '11' is set by a router to indicate congestion to
the end nodes. The term 'CE packet' denotes a packet that has the CE
codepoint set.
The ECN-Capable Transport (ECT) codepoints '10' and '01' (ECT(0) and
ECT(1) respectively) are set by the data sender to indicate that the
end-points of the transport protocol are ECN-capable. Routers treat
the ECT(0) and ECT(1) codepoints as equivalent. Senders are free to
Briscoe Expires September 6, 2006 [Page 39]
Internet-Draft Framework using Pre-Congestion Notification March 2006
use either the ECT(0) or the ECT(1) codepoint to indicate ECT, on a
packet-by-packet basis. The use of both the two codepoints for ECT is
motivated primarily by the desire to allow mechanisms for the data
sender to verify that network elements are not erasing the CE
codepoint, and that data receivers are properly reporting to the
sender the receipt of packets with the CE codepoint set.
ECN requires support from the transport protocol, in addition to the
functionality given by the ECN field in the IP packet header.
[RFC3168] addresses the addition of ECN Capability to TCP, specifying
three new pieces of functionality: negotiation between the endpoints
during connection setup to determine if they are both ECN-capable; an
ECN-Echo (ECE) flag in the TCP header so that the data receiver can
inform the data sender when a CE packet has been received; and a
Congestion Window Reduced (CWR) flag in the TCP header so that the
data sender can inform the data receiver that the congestion window
has been reduced.
The transport layer (e.g.. TCP) must respond, in terms of congestion
control, to a *single* CE packet as it would to a packet drop.
The advantage of setting the CE codepoint as an indication of
congestion, instead of relying on packet drops, is that it allows the
receiver(s) to receive the packet, thus avoiding the potential for
excessive delays due to retransmissions after packet losses.
11.2. Appendix B: What is distributed measurement-based admission
control?
This Appendix briefly explains what distributed measurement-based
admission control is [Breslau99].
Traditional admission control algorithms for 'hard' real-time
services (those providing a firm delay bound for example) guarantee
QoS by using 'worst case analysis'. Each time a flow is admitted its
traffic parameters are examined and the network re-calculates the
remaining resources. When the network gets a new request it therefore
knows for certain whether the prospective flow, with its particular
parameters, should be admitted. However, parameter-based admission
control algorithms result in under-utilisation when the traffic is
bursty. Therefore 'soft' real time services - like Controlled Load -
can use a more relaxed admission control algorithm.
This insight suggests measurement-based admission control (MBAC). The
aim of MBAC is to provide a statistical service guarantee. The
Briscoe Expires September 6, 2006 [Page 40]
Internet-Draft Framework using Pre-Congestion Notification March 2006
classic scenario for MBAC is where each node participates in hop-by-
hop admission control, characterising existing traffic locally
through measurements (instead of keeping an accurate track of traffic
as it is admitted), in order to determine the current value of some
parameter e.g. load. Note that for scalability the measurement is of
the aggregate of the flows in the local system. The measured
parameter(s) is then compared to the requirements of the prospective
flow to see whether it should be admitted.
MBAC may also be performed centrally for a network, it which case it
uses centralised measurements by a bandwidth broker.
We use distributed MBAC. "Distributed" means that the measurement is
accumulated for the 'whole-path' using in-band signalling. In our
case, this means that the measurement of existing traffic is for the
same pair of ingress and egress gateways as the prospective
microflow.
In fact our mechanism can be said to be distributed in three ways:
all nodes on the ingress-egress path affect the Congestion-Level-
Estimate; the admission control decision is made just once on behalf
of all the nodes on the path across the CL-region; and the ingress
and egress gateways cooperate to perform MBAC.
11.3. Appendix C: Calculating the Exponentially weighted moving average
(EWMA)
At the egress gateway, for every CL packet arrival:
[EWMA-total-bits]n+1 = (w * bits-in-packet) + ((1-w) * [EWMA-
total-bits]n )
[EWMA-AM-bits]n+1 = (B * w * bits-in-packet) + ((1-w) * [EWMA-AM-
bits]n )
Then, per new flow arrival:
[Congestion-Level-Estimate]n+1 = [EWMA-AM-bits]n+1 / [EWMA-total-
bits]n+1
where
Briscoe Expires September 6, 2006 [Page 41]
Internet-Draft Framework using Pre-Congestion Notification March 2006
EWMA-total-bits is the total number of bits in CL packets, calculated
as an exponentially weighted moving average (EWMA)
EWMA-AM-bits is the total number of bits in CL packets that are
Admission Marked, again calculated as an EWMA.
B is either 0 or 1:
B = 0 if the CL packet is not admission marked
B = 1 if the CL packet is admission marked
w is the exponential weighting factor.
Varying the value of the weight trades off between the smoothness and
responsiveness of the Congestion-Level-Estimate. However, in general
both can be achieved, given our original assumption of many CL
microflows and remembering that the EWMA is calculated on the basis
of aggregate traffic between the ingress and egress gateways.
There will be a threshold inter-arrival time between packets of the
same aggregate below which the egress will consider the estimate of
the Congestion-Level-Estimate as too stale, and it will then trigger
generation of probes by the ingress.
The first two per-packet algorithms can be simplified, if their only
use will be where the result of one is divided by the result of the
other in the third, per-flow algorithm.
[EWMA-total-bits]'n+1 = bits-in-packet + (w' * [EWMA- total-
bits]n )
[EWMA-AM-bits]'n+1 = (B * bits-in-packet) + (w' * [EWMA-AM-bits]n
)
where w' = (1-w)/w.
If w' is arranged to be a power of 2, these per packet algorithms can
be implemented solely with a shift and an add.
Briscoe Expires September 6, 2006 [Page 42]
Internet-Draft Framework using Pre-Congestion Notification March 2006
12. References
A later version will distinguish normative and informative
references.
[AGGRE-TE] Francois Le Faucheur, Michael Dibiasio, Bruce Davie,
Michael Davenport, Chris Christou, Jerry Ash, Bur
Goode, 'Aggregation of RSVP Reservations over MPLS
TE/DS-TE Tunnels', draft-ietf-tsvwg-rsvp-dste-00 (work
in progress), July 2005
[ANSI.MLPP.Spec] American National Standards Institute,
"Telecommunications- Integrated Services Digital
Network (ISDN) - Multi-Level Precedence and Pre-
emption (MLPP) Service Capability", ANSI T1.619-1992
(R1999), 1992.
[ANSI.MLPP.Supplement] American National Standards Institute, "MLPP
Service Domain Cause Value Changes", ANSI ANSI
T1.619a-1994 (R1999), 1990.
[AVQ] S. Kunniyur and R. Srikant "Analysis and Design of an
Adaptive Virtual Queue (AVQ) Algorithm for Active
Queue Management", In: Proc. ACM SIGCOMM'01, Computer
Communication Review 31 (4) (October, 2001).
[Breslau99] L. Breslau, S. Jamin, S. Shenker "Measurement-based
admission control: what is the research agenda?", In:
Proc. Int'l Workshop on Quality of Service 1999.
[Breslau00] L. Breslau, E. Knightly, S. Shenker, I. Stoica, H.
Zhang "Endpoint Admission Control: Architectural
Issues and Performance", In: ACM SIGCOMM 2000
[Briscoe] Bob Briscoe and Steve Rudkin, "Commercial Models for
IP Quality of Service Interconnect", BT Technology
Journal, Vol 23 No 2, April 2005.
[DCAC] Richard J. Gibbens and Frank P. Kelly "Distributed
connection acceptance control for a connectionless
network", In: Proc. International Teletraffic Congress
(ITC16), Edinburgh, pp. 941—952 (1999).
[EMERG-RQTS] Carlberg, K. and R. Atkinson, "General Requirements
for Emergency Telecommunication Service (ETS)", RFC
3689, February 2004.
Briscoe Expires September 6, 2006 [Page 43]
Internet-Draft Framework using Pre-Congestion Notification March 2006
[EMERG-TEL] Carlberg, K. and R. Atkinson, "IP Telephony
Requirements for Emergency Telecommunication Service
(ETS)", RFC 3690, February 2004.
[Floyd] S. Floyd, 'Specifying Alternate Semantics for the
Explicit Congestion Notification (ECN) Field', draft-
floyd-ecn-alternates-02.txt (work in progress), August
2005
[GSPa] Karsten (Ed.), Martin "GSP/ECN Technology &
Experiments", Deliverable: 15.3 PtIII, M3I Eu Vth
Framework Project IST-1999-11429, URL:
http://www.m3i.org/ (February, 2002) (superseded by
[GSP-TR])
[GSP-TR] Martin Karsten and Jens Schmitt, "Admission Control
Based on Packet Marking and Feedback Signalling --
Mechanisms, Implementation and Experiments", TU-
Darmstadt Technical Report TR-KOM-2002-03, URL:
http://www.kom.e-technik.tu-
darmstadt.de/publications/abstracts/KS02-5.html (May,
2002)
[ITU.MLPP.1990] International Telecommunications Union, "Multilevel
Precedence and Pre-emption Service (MLPP)", ITU-T
Recommendation I.255.3, 1990.
[Johnson] DM Johnson, 'QoS control versus generous
dimensioning', BT Technology Journal, Vol 23 No 2,
April 2005
[PCN] B. Briscoe, P. Eardley, D. Songhurst, F. Le Faucheur,
A. Charny, V. Liatsos, S. Dudley, J. Babiarz, K.
Chan. 'Pre-Congestion Notification marking', draft-
briscoe-tsvwg-cl-phb-01 (work in progress), March
2006.
[Re-ECN] Bob Briscoe, Arnaud Jacquet, Alessandro Salvatori,
'Re-ECN: Adding Accountability for Causing Congestion
to TCP/IP', draft-briscoe-tsvwg-re-ecn-tcp-01 (work in
progress), March 2006.
[Re-feedback] Bob Briscoe, Arnaud Jacquet, Carla Di Cairano-
Gilfedder, Andrea Soppera, 'Re-feedback for Policing
Congestion Response in an Inter-network', ACM SIGCOMM
2005, August 2005.
Briscoe Expires September 6, 2006 [Page 44]
Internet-Draft Framework using Pre-Congestion Notification March 2006
[Re-PCN] B. Briscoe, 'Emulating Border Flow Policing using Re-
ECN on Bulk Data', draft-briscoe-tsvwg-re-ecn-border-
cheat-00 (work in progress), February 2006.
[Reid] ABD Reid, 'Economics and scalability of QoS
solutions', BT Technology Journal, Vol 23 No 2, April
2005
[RFC2211] J. Wroclawski, Specification of the Controlled-Load
Network Element Service, September 1997
[RFC2309] Braden, B., et al., "Recommendations on Queue
Management and Congestion Avoidance in the Internet",
RFC 2309, April 1998.
[RFC2474] Nichols, K., Blake, S., Baker, F. and D. Black,
"Definition of the Differentiated Services Field (DS
Field) in the IPv4 and IPv6 Headers", RFC 2474,
December 1998
[RFC2475] Blake, S., Black, D., Carlson, M., Davies, E., Wang,
Z. and W. Weiss, 'A framework for Differentiated
Services', RFC 2475, December 1998.
[RFC2597] Heinanen, J., Baker, F., Weiss, W. and J. Wrocklawski,
"Assured Forwarding PHB Group", RFC 2597, June 1999.
[RFC2998] Bernet, Y., Yavatkar, R., Ford, P., Baker, F., Zhang,
L., Speer, M., Braden, R., Davie, B., Wroclawski, J.
and E. Felstaine, "A Framework for Integrated Services
Operation Over DiffServ Networks", RFC 2998, November
2000.
[RFC3168] Ramakrishnan, K., Floyd, S. and D. Black "The Addition
of Explicit Congestion Notification (ECN) to IP", RFC
3168, September 2001.
[RFC3246] B. Davie, A. Charny, J.C.R. Bennet, K. Benson, J.Y. Le
Boudec, W. Courtney, S. Davari, V. Firoiu, D.
Stiliadis, 'An Expedited Forwarding PHB (Per-Hop
Behavior)', RFC 3246, March 2002.
[RFC3270] Le Faucheur, F., Wu, L., Davie, B., Davari, S.,
Vaananen, P., Krishnan, R., Cheval, P., and J.
Heinanen, "Multi- Protocol Label Switching (MPLS)
Support of Differentiated Services", RFC 3270, May
2002.
Briscoe Expires September 6, 2006 [Page 45]
Internet-Draft Framework using Pre-Congestion Notification March 2006
[RMD] Attila Bader, Lars Westberg, Georgios Karagiannis,
Cornelia Kappler, Tom Phelan, 'RMD-QOSM - The Resource
Management in DiffServ QoS model', draft-ietf-nsis-
rmd-03 Work in Progress, June 2005.
[RSVP-ECN] Francois Le Faucheur, Anna Charny, Bob Briscoe, Philip
Eardley, Joe Barbiaz, Kwok-Ho Chan, 'RSVP Extensions
for Admission Control over DiffServ using Pre-
congestion Notification', draft-lefaucheur-rsvp-ecn-00
(work in progress), October 2005.
[RTECN] Babiarz, J., Chan, K. and V. Firoiu, 'Congestion
Notification Process for Real-Time Traffic', draft-
babiarz-tsvwg-rtecn-04 Work in Progress, July 2005.
[RTECN-usage] Alexander, C., Ed., Babiarz, J. and J. Matthews,
'Admission Control Use Case for Real-time ECN', draft-
alexander-rtecn-admission-control-use-case-00, Work in
Progress, February 2005.
[vq] Costas Courcoubetis and Richard Weber "Buffer Overflow
Asymptotics for a Switch Handling Many Traffic
Sources" In: Journal Applied Probability 33 pp. 886--
903 (1996).
Authors' Addresses
Bob Briscoe
BT Research
B54/77, Sirius House
Adastral Park
Martlesham Heath
Ipswich, Suffolk
IP5 3RE
United Kingdom
Email: bob.briscoe@bt.com
Briscoe Expires September 6, 2006 [Page 46]
Internet-Draft Framework using Pre-Congestion Notification March 2006
Dave Songhurst
BT Research
B54/69, Sirius House
Adastral Park
Martlesham Heath
Ipswich, Suffolk
IP5 3RE
United Kingdom
Email: dsonghurst@jungle.bt.co.uk
Philip Eardley
BT Research
B54/77, Sirius House
Adastral Park
Martlesham Heath
Ipswich, Suffolk
IP5 3RE
United Kingdom
Email: philip.eardley@bt.com
Francois Le Faucheur
Cisco Systems, Inc.
Village d'Entreprise Green Side - Batiment T3
400, Avenue de Roumanille
06410 Biot Sophia-Antipolis
France
Email: flefauch@cisco.com
Anna Charny
Cisco Systems
300 Apollo Drive
Chelmsford, MA 01824
USA
Email: acharny@cisco.com
Kwok Ho Chan
Nortel Networks
600 Technology Park Drive
Billerica, MA 01821
USA
Email: khchan@nortel.com
Briscoe Expires September 6, 2006 [Page 47]
Internet-Draft Framework using Pre-Congestion Notification March 2006
Jozef Z. Babiarz
Nortel Networks
3500 Carling Avenue
Ottawa, Ont K2H 8E9
Canada
Email: babiarz@nortel.com
Stephen Dudley
Nortel Networks
4001 E. Chapel Hill Nelson Highway
P.O. Box 13010, ms 570-01-0V8
Research Triangle Park, NC 27709
USA
Email: smdudley@nortel.com
Intellectual Property Statement
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org
Disclaimer of Validity
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
Briscoe Expires September 6, 2006 [Page 48]
Internet-Draft Framework using Pre-Congestion Notification March 2006
INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Copyright Statement
Copyright (C) The Internet Society (2006).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
Briscoe Expires September 6, 2006 [Page 49]
| PAFTECH AB 2003-2026 | 2026-04-21 22:24:40 |